en-us
2
Table of contents
1 IMPORTANT SAFETY INSTRUCTIONS.................... 3
1.1 Safety definitions....................................................... 4
1.2 General information................................................... 4
1.3 General safety instructions........................................ 4
1.4 Appliance handling safety ......................................... 5
1.5 Installation location.................................................... 5
1.6 Safety codes and standards...................................... 5
1.7 Electrical safety......................................................... 5
1.8 Gas safety................................................................. 6
1.9 Propane gas installation............................................ 6
1.10 Conversion to Liquified Petroleum gas.................... 6
1.11 Ventilation recommendations .................................. 7
1.12 High altitude installation .......................................... 7
1.13 State of California Proposition 65 Warnings ............ 7
1.14 Transport ................................................................ 7
2 Before you begin....................................................... 9
2.1 Tools and parts needed ............................................ 9
2.2 Parts included ........................................................... 9
2.3 Removing packaging............................................... 10
2.4 General information................................................. 11
2.5 Cabinet requirements.............................................. 12
2.6 Technical data......................................................... 13
2.7 Installation checklist ................................................ 14
3 Installation procedure ............................................ 14
3.1 How to remove the oven door ................................. 14
3.2 Fitting the rear vent trim .......................................... 15
3.3 Fitting the adjustable feet ........................................ 15
3.4 Connect gas supply................................................. 16
3.5 Checking the gas line for leaks ............................... 17
3.6 Install appliance ...................................................... 17
3.7 Installing the anti-tip bracket.................................... 17
3.8 Connect electrical supply ........................................ 19
3.9 Preparation for power connection............................ 19
3.10 Four-wire range cord connection (recommended
method)................................................................. 20
3.11 Connecting the three-wire range cord (alternate
method)................................................................. 21
3.12 Connecting the four-wire flexible conduit............... 22
3.13 Connecting the three-wire flexible conduit............. 23
3.14 Burner assembly ................................................... 23
3.15 Check the installation............................................ 25
3.16 Test for gas leaks.................................................. 25
4 Conversion to Propane gas (LPG) ......................... 25
4.1 Parts included with propane gas nozzle set ............ 25
4.2 Orifices.................................................................... 28
4.3 Setting the pressure regulator for propane gas ....... 28
4.4 Replacing the main control nozzles......................... 28
4.5 Setting the minimum gas flow ................................. 29
4.6 Checking functions after the conversion.................. 29
4.7 Conversion to natural gas ....................................... 29
5 Customer Service..................................................... 30
5.1 Model number (E-Nr.) and production number
(FD).......................................................................... 30
5.2 Rating plate location................................................. 30
6 Wiring diagram for HDS8..5. .................................... 31
en-us
3
Read all instructions carefully before use. These precautions will reduce the risk of electrical shock, fire and injury to
persons. When using kitchen appliances, basic safety precautions must be followed including those in the following
pages.
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
en-us
4
1.1 Safety definitions
Here you can find explanations of the safety signal words
used in this manual.
WARNING
This indicates that death or serious injuries may occur as
a result of non-observance of this warning.
CAUTION
This indicates that minor or moderate injuries may occur
as a result of non-observance of this warning.
NOTICE:
This indicates that damage to the appliance or property
may occur as a result of non-compliance with this
advisory.
Note:This alerts you to important information and/or tips.
1.2 General information
¡Read this manual carefully.
¡Do not connect the appliance if it has been damaged in
transit.
1.3 General safety instructions
IMPORTANT: THE APPLIANCE MUST BE INSTALLED
BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE THESE INSTRUCTIONS FOR THE
LOCAL ELECTRICAL INSPECTOR’S USE.
OWNER: PLEASE RETAIN THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
INSTALLER: LEAVE THESE INSTRUCTIONS WITH
THE APPLIANCE AFTER INSTALLATION IS
COMPLETE.
Examine the appliance after unpacking it. In the event of
transport damage, do not plug it in.
This appliance is intended for use up to a maximum height
of 6,560feet (2000meters) above sea level.
WARNING
If the information in this manual is not followed exactly, fire
or shock may result causing property damage or personal
injury.
Do not repair, replace or remove any part of the appliance
unless specifically recommended in the manuals.
Improper installation, service or maintenance can cause
injury or property damage.
▶Refer to this manual for guidance.
▶All other servicing should be done by an authorized
service provider.
WARNING
TIP OVER HAZARD! A child or adult can tip the range
over and be killed.
▶Install the anti-tip device to the structure and/or the
range.
▶Verify the anti-tip device has been properly installed
and engaged.
▶Engage the range to the anti-tip device. Ensure the
anti-tip device is re-engaged when the range is moved.
▶Re-engage the anti-tip device if the range is moved. Do
not operate the range without the anti-tip device in
place and engaged.
▶See installation instructions for details.
▶Failure to follow the instructions in this manual can
result in death or serious burns to children and adults.
▶Check for proper installation and use of the anti-tip
bracket. Carefully tip the range forward pulling from the
back to ensure that the anti-tip bracket engages the
range leg and prevents tip-over. The range should not
move more than 1" (2.5cm).
WARNING
Disconnect electrical and gas supply before servicing.
Never modify or alter the construction of the appliance.
▶For example, do not remove leveling legs, panels, wire
covers or anti-tip brackets/screws.
The appliance should only be used if installed by a
qualified technician in accordance with these installation
instructions and all applicable regulations and codes. The
manufacturer is not responsible for any damage resulting
from incorrect installation.
To eliminate the risk of burns or fire by reaching over
heated surface units, cabinet storage space located above
the surface units should be avoided.
▶If cabinet storage is to be provided, the risk can be
reduced by installing a hood that projects horizontally a
minimum of 5" (127mm) beyond the bottom of the
cabinet.
▶Verify that cabinets above the cooktop are a maximum
of 13" (330mm) deep.
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
en-us
5
WARNING
Remove all tape and packaging before using the
appliance.
▶Destroy the packaging after unpacking the appliance.
▶Dispose of packaging in an environmentally responsible
manner.
▶Never allow children to play with packaging material.
▶Store small parts safely as they can be a choke hazard.
Before starting up the appliance, remove any packaging
material and adhesive film from the oven cavity and the
door.
1.4 Appliance handling safety
WARNING
Unit is heavy and requires at least two people or
proper equipment to move.
▶Do not lift appliance by door handle.
▶Remove the door for easier handling and installation.
See instructions in this manual.
WARNING
Hidden surfaces may have sharp edges.
▶Use caution when reaching behind or under appliance.
▶Wear gloves to avoid cutting fingers on sharp edges
during installation.
WARNING
Do not use the oven for storage.
1.5 Installation location
To eliminate the risk of burns or fire by reaching over
heated surface units, cabinet storage space located above
the surface units should be avoided. If cabinet storage is
to be provided, the risk can be reduced by installing a
hood that projects horizontally a minimum of 5" (12.7cm)
beyond the bottom of the cabinet.
Verify that cabinets above the range are a maximum of
13" (330 mm) deep.
1.6 Safety codes and standards
This appliance complies with the latest version of one or
more of the following standards:
¡CAN/CSA C22.2 No. 61 - Household Cooking Ranges
¡UL 858 - Household Electric Ranges
¡ANSI Z21.1b-2012 Household Cooking Gas Appliances
¡Installation must conform with local codes or, in the
absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1/NFPA 54 or, in Canada, the
Natural Gas and Propane Installation Code, CSA
B149.1.
It is the responsibility of the owner and the installer to
determine if additional requirements and/or standards
apply to specific installations.
1.7 Electrical safety
¡Installer - show the owner the location of the circuit
breaker or fuse. Mark it for easy reference.
¡If required by the National Electrical Code (or Canadian
Electrical Code), this appliance must be installed on a
separate branch circuit.
¡Local codes vary. The installer is responsible for
ensuring that the installation, connections, and
grounding comply with all applicable codes. The
manufacturer is not responsible for any issues
associated with the improper installation of this product.
¡Be sure your appliance is properly installed and
grounded by a qualified technician.
¡The circuit breaker should have a contact separation of
at least 3mm on all poles.
¡Do not use an adapter.
¡Refer to the rating plate for more information.
→
"Rating plate location", Page30
WARNING
Before installing, turn power OFF at the service panel.
▶Lock service panel to prevent power from being turned
ON accidentally.
ELECTRIC SHOCK HAZARD
▶Disconnect power before installing or servicing. Before
turning power ON, be sure that all controls are in the
OFF position.
▶DO NOT remove connections.
▶DO NOT use an extension cord.
▶Improper grounding can result in a risk of electric
shock.
▶Failure to follow these instructions can result in death,
fire, or electrical shock.
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
en-us
6
GROUNDING INSTRUCTIONS
▶This appliance must be grounded.
▶Grounding reduces the risk of electric shock by
providing a safe pathway for electric current in the
event of a short circuit.
▶Be sure your appliance is properly installed and
grounded by a qualified technician.
▶Installation, electrical connections and grounding must
comply with all applicable codes.
Do not use an extension cord. If the power supply cord is
too short, have a qualified electrician install an outlet near
the appliance.
Before you turn on power supply, make sure all controls
are in the OFF position.
1.8 Gas safety
Requirements for gas supply:
¡Install a gas shutoff valve near the appliance. It must be
easily accessible in an emergency.
¡Leak testing must be conducted by the installer
according to the instructions in this manual.
¡The appliance and its individual shutoff valve must be
disconnected from the gas supply piping system during
any pressure testing at pressures in excess of ½psi
(3.5kPa).
¡The appliance must be isolated from the gas supply
piping system by closing its individual manual shutoff
valve during any pressure testing of the gas supply
piping system at test pressures equal to or less than
½psi (3.5kPa).
¡The minimum supply pressure must be 1" water column
above the manifold pressure printed on the rating label.
The maximum supply pressure must not exceed 14.0
inches water column (34.9Millibars).
¡A metal flex line or fixed metal pipe shall be used to
connect gas to the appliance. If a metal gas line cannot
be used, consult your local certified electrician or local
electric codes for proper grounding.
IMPORTANT SAFETY NOTICE: Burning gas cooking fuel
generates some by-products which are on the list of
substances which are known by the State of California to
cause cancer or reproductive harm. To minimize exposure
to these substances, always operate this unit according to
the instructions contained in this booklet and provide good
ventilation.
1.9 Propane gas installation
¡The propane gas tank must be equipped with its own
high pressure regulator. In addition, the regulator
supplied with this unit must also be used.
¡The appliance is shipped from the factory for use with
natural gas. It must be converted for use with propane.
A qualified technician or certified installer must do the
conversion.
¡This appliance has been certified for safe operation up
to a height of 10,000 ft.
Exception: For use with propane the appliance must be
converted per the LP conversion instructions.
→
"Conversion to Propane gas (LPG)", Page25
For Massachusetts installations
¡Installation must be performed by a qualified or
licensed contractor, plumber or gas fitter qualified or
licensed by the state, province or region where this
appliance is being installed.
¡Shut-off valve must be a “T” handle gas cock.
¡Flexible gas connector must not be longer than
36inches.
Installer - show the owner where the gas shut-off valve is
located.
1.10 Conversion to Liquified Petroleum
gas
WARNING
Personal injury or death from electrical shock may occur,
if the range is not installed by a qualified installer or
electrician. Any additions, changes, or conversions
required in order for this appliance to satisfactorily meet
the application needs must be made by a qualified
technician.
Your gas range model is designed to allow for LP
conversion by a qualified service technician.
▶Before installing the kit, be sure to follow the LP
Installation Instructions carefully.
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
en-us
7
1.11 Ventilation recommendations
We strongly recommend the installation of a ventilation
hood above this appliance.
The hood must be installed according to instructions
furnished with the hood.
WARNING
The appliance should not be installed with a ventilation
system that blows air downward toward the burners. This
type of ventilation system may cause ignition and
combustion problems with the gas cooking appliance
resulting in personal injury or unintended operation.
1.12 High altitude installation
This appliance has been tested for operation up to an
altitude of 10,000ft (3,048m) elevation above sea level.
If desired, for altitudes above 2,000ft (610m) elevation
above sea level, adjustments may be made. Burners
should be checked at the lowest setting, if the flame is not
stable the simmer should be increased until the flame is
stable. This can be done by adjusting the bypass screw in
the valve. If flame performance is satisfactory, adjustment
will not be required. It is required that a Certified
Professional make the high altitude adjustments during
installation. High altitude nozzle sets for natural gas and
propane gas are available for installations at
2,000-6,500ft (610-1,981m) or 6,501-10,000ft
(1,982-3,048m) if the adjustments using the bypass
screw don’t resolve performance issues.
1.13 State of California Proposition 65
Warnings
This product may contain a chemical known to the State
of California, which can cause cancer or reproductive
harm. Therefore, the packaging of your product may bear
the following label as required by California:
1.14 Transport
Follow these precautions when transporting your
appliance.
NOTICE:
To avoid damaging the appliance, use the transport
method shown in the following picture.
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
en-us
8
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
Before you begin en-us
9
Before you begin
2 Before you begin
Before you begin
2.1 Tools and parts needed
¡Phillips head screwdriver
¡Slotted screwdriver 1/8" (3,5mm)
¡Adjustable wrench
¡Tongue and groove pliers
¡Socket or flat wrench 3/8” (10mm) or tongs
¡Socket or flat wrench 7/8” (22 mm) or tongs
¡Drill with 5/16" (8mm) bit
¡Pencil
¡Tape measure
¡Teflon tape or pipe-joint compound
Only needed for appliances without power cord:
¡Tube hexagonal wrench with nut head 3/8” (10mm)
¡Tube hexagonal wrench with nut head 5/16” (8mm)
¡Power Supply Cord (only for USA)
Note:Additional materials may be necessary for
installation in solid surface countertops. Contact the
countertop manufacturer.
2.2 Parts included
30" Range:
en-us Before you begin
10
36" Range: 2.3 Removing packaging
See the diagram on the packaging.
1. If straps are present, cut the straps.
2. Cut the plastic down the back of unit making sure not to
cut the unit.
3. Remove the plastic film.
4. Lift the cardboard carton from the top of the range and
dispose of it.
5. Remove the corner posts, making sure that any other
packaging materials running between the corner posts
are also removed.
6. Remove all internal packaging and tape.
7. The rear vent trim is nested in the styrofoam packaging
for shipping purposes. Do not throw it away.
Before you begin en-us
11
2.4 General information
30" Range:
en-us Before you begin
12
36" Range:
2.5 Cabinet requirements
X Grounded Outlet
Y Gas Supply Line
The minimum distances that must be maintained when
installing the range shall be:
B minimum 18" (457mm)
C minimum 30" (762mm) clearance between the
top of the cooking surface and the bottom of the
unprotected wood or metal cabinet
D 30": minimum 30" (762mm)
36": minimum 36" (914mm)
E minimum 25" (635mm)
F maximum 13" (330mm)
G 30": minimum 30" (762mm)
36": minimum 36" (914mm)
Zero clearance between adjacent combustible
construction below the countertop surface and
sides of the appliance.
H 30": 35"⅜-36"⅝ (898 - 930mm)
36": 35"⁹⁄₁₆-36"⅝ (903 - 930mm)
I 11" (279mm)
J 7" (178mm)
K 6" (150mm)
L 11" (279mm)
Before you begin en-us
13
Choose one of the following built-in configurations.
Installation allowed only with non combustible back wall
Option 1: A >= 12'' (305mm) and B >= 28'' (711mm)
Option 2: A >= 28'' (711mm) and B >= 12'' (305mm)
* Clearances from non-combustible materials are not part
of the ANSI Z21.1 scope and are not certified by Intertek.
Clearances of less than 3'' (76mm) should be approved
by the local codes and/or by the local authority having
jurisdiction.
Island Installation (applicable both with non combustible
back wall and combustible back wall)
Option 1: A >= 12'' (305mm) and B >= 28'' (711mm)
Option 2: A >= 28'' (711mm) and B >= 12'' (305mm)
* purchased separately
** Clearances from non-combustible materials are not part
of the ANSI Z21.1 scope and are not certified by Intertek.
Clearances of less than 3'' (76mm) should be approved
by the local codes and/or by the local authority having
jurisdiction.
Low Backguard Installation (applicable both with non
combustible back wall and combustible back wall)
Option 1: A >= 12'' (305mm) and B >= 28'' (711mm)
Option 2: A >= 28'' (711mm) and B >= 12'' (305mm)
* purchased separately
** Clearances from non-combustible materials are not part
of the ANSI Z21.1 scope and are not certified by Intertek.
Clearances of less than 3'' (76 mm) should be approved
by the local codes and/or by the local authority having
jurisdiction.
2.6 Technical data
30" (5 burners):
Total connected load electric ¡120/208V,
12A
(2500W)
¡120/240V,
14A
(3400W)
Total connected load gas (natural gas) 48,000BTU/h
(14.1kW)
Total connected load gas (propane
gas)
48,000BTU/h
(14.1kW)
36" (6 burners):
Total connected load electric ¡120/208V,
12A
(2500W)
¡120/240V,
14A
(3400W)
Total connected load gas (natural gas) 63,000BTU/h
(18.4kW)
Total connected load gas (propane
gas)
63,000BTU/h
(18.4kW)
en-us Installation procedure
14
2.7 Installation checklist
Please refer to the following pages for complete
installation instructions. Use this checklist to verify that you
have completed each step of the installation process. This
can help you avoid mistakes.
Installation step
Before installing the range, be sure to verify the
cabinet dimensions are correct for your unit and
that the required electrical and gas connections
are present.
Before installing the range, make sure that any
opening in the wall behind the appliance and in
the floor under the appliance shall be sealed.
Read this installation manual for content
regarding Safety, Cabinet Dimensions,
Removing Packaging, Electrical Installation,
Gas Connection, and Customer Service.
Removing the oven door prior to installation
reduces the unit weight and makes the range
easier to move. Additionally, the removal of the
oven door provides access to handholds for
lifting.
Install and adjust the feet.
Prepare the gas connection.
Move the range (2 people needed) into place in
front of the installation opening, leaving the
bottom packaging on the unit to avoid damaging
flooring.
Plug the range into a properly configured
receptacle.
Protect the flooring from damage, then slide the
unit all the way into place, making sure to route
the power cord correctly.
Reinstall the oven door.
Make sure the anti-tip bracket is engaged.
Installation procedure
3 Installation procedure
Installation procedure
An air curtain or other overhead range hood, which
operates by blowing a downward airflow onto a range,
shall not be used in conjunction with the gas range unless
the hood and range have been designed and tested in
accordance with ANSI Z21.1 and listed by an independent
testing laboratory for combination use.
3.1 How to remove the oven door
WARNING
Failure to follow these instructions when removing the
oven door may lead to personal injury or product damage.
▶Make sure oven is cool and power to the oven has been
turned off before removing the door. Failure to do so
could result in electrical shock or burns.
▶The oven door is heavy and parts of it are fragile. Use
both hands to remove the oven door.
▶The door front is glass. Handle it carefully to avoid
breakage.
▶Grasp only the side of the oven door. Do not grasp the
handle. It may swing in your hand and cause damage or
injury. Failure to grasp the oven door firmly and properly
could result in personal injury or product damage.
▶To avoid injury from hinge bracket snapping closed, be
sure both levers are securely in place before removing
the door.
▶Do not force the door open or closed. The hinge could
be damaged and cause damage or injury.
▶Do not lay the removed door on sharp or pointed
objects as this could break the glass. Lay it on a flat,
smooth surface, positioned so that the door cannot fall
over.
Note:To avoid injury or damage, make sure that you read
the above WARNING before attempting to remove the
oven door.
1. Open the oven door to its fully open position.
2. Lock the two hinges on the left and right using the
locking pin. The locking pins must be fully inserted into
the holes in the hinges.
Installation procedure en-us
15
3. CAUTION Closing the door by 8" (203mm) takes
the pressure off the spring. If this is not done, the door
can still be removed but the latch will now slam shut
and may pinch or cut your hand.
Close the oven door until it catches on the hinge stop
levers, locking the hinges at the correct angle for door
removal. The door can be removed when it is pulled up
from the open position by about 8 inches (203mm).
This takes the tension off the spring-loaded hinges so
that the door can be easily lifted out.
4. The door is heavy. Use both hands to firmly grip it by
the sides. Do not grip the door by the handle. Keeping
the angle of the door the same, lift the door straight up
approximately 3/4" (19mm) to unhook the hinges from
the slots. Pull the door out towards you until the hinges
are clear of the oven housing.
5. Place the door in a convenient and stable location for
cleaning.
6. Refit the door in the reverse order in which it was
removed.
Note:Do not throw away the locking pins. Keep them in a
safe place. They will be needed anytime the door is
removed from the appliance.
3.2 Fitting the rear vent trim
1. The rear vent trim is nested in the styrofoam packaging.
Remove the packaging and the protective film from the
rear vent trim.
2. Place the rear vent trim into the holes intended for this
purpose using the dowel pins.
3. Insert and tighten the enclosed screws from below.
3.3 Fitting the adjustable feet
NOTICE:
Do not use the door handle or projecting control panel for
carrying.
1.
NOTICE:
In order to prevent the risk of damaging the
feet during installation, they must be installed as close
as possible from the final appliance location.
Move the appliance as close as possible to the final
appliance location.
2.
NOTICE:
Protect the floor.
Remove all parts that are not permanently fixed,
especially the pan supports and burners.
3. Remove the accessories from the oven.
4. Tilt the appliance and put it to the floor on the backside.
5. Screw the adjustable feet into the mounting holes on
the underside of the appliance.
6. Screw the adjustable feet in fully.
7. CAUTION Feet or appliance bottom case can be
damaged while moving the appliance back onto its feet.
Carefully move the appliance back onto its feet.
en-us Installation procedure
16
8. Turn the adjustable feet to align the appliance.
Notes
¡Measure the installation height of the cabinetry and
adjust appliance height accordingly prior to placing
appliance in cabinetry.
¡Carefully move the appliance to its final position, only if
legs are well adjusted.
3.4 Connect gas supply
The appliance is shipped from the factory for use with
natural gas at a pressure of 5" water column.
¡When checking for proper operation of the regulator, the
inlet pressure must be at least 1" greater than the
operating (manifold) pressure above. When used with
natural gas, the pressure supplied to the regulator must
be between 6" and 10.5" water column.
¡To convert the appliance to propane gas see
“Conversion to propane gas (LPG)”. A qualified
technician or installer must do the conversion.
¡Use a flexible gas pipe with a length of at least 5ft (1.5
m).
¡The gas inlet to the unit is located at the right rear of the
appliance.
¡Install the pressure regulator (supplied with unit) to gas
inlet. Postion the gasket (supplied with unit) in between
the inlet and the regulator. Position the regulator to
have it cap D →
Page28
easily accessible. Turn the
nut on gas inlet to hand tighten plus 1/3 turn.
¡Install the gas pipe to the regulator using Teflon tape or
pipe-joint compound (resistant to propane gas and
natural gas). Turn to hand tighten plus 1/3 turn. Do not
exceed 1 turn for alignment, to prevent possible
damage to the gas pressure regulator.
Check inlet fittings and regulator for leaks.
* Attached to the appliance.
WARNING
Do not attempt any adjustment of the pressure regulator,
except when converting to propane. Adjustments could
lead to leaks or cause incorrect gas pressure to the
appliance.
Side and back view of gas range installation
Gas Location
A Gas connection
B Electrical connection
Connect the gas supply line to the unit pressure regulator
using a 1/2” flex gas line connector between manual shut-
off valve and pressure regulator. A metal flex line or fixed
metal pipe shall be used to connect gas to the appliance.
If a metal gas line cannot be used, consult your local
certified electrician or local electric codes for proper
grounding.
Installation procedure en-us
17
3.5 Checking the gas line for leaks
Check supply line connections for leaks using a soap
solution or non-corrosive leak detection fluid. Do not use a
flame of any sort.
WARNING
Install a gas shut off valve near the appliance. After
installation, it must be easily accessible in an emergency.
1. Turn on gas.
2. Apply a soap solution or non-corrosive leak detection
fluid to all joints and fittings in the gas connection
between the shut-off valve and the cooktop. Include gas
fittings and joints in the cooktop if connections may
have been disturbed during installation. Bubbles
appearing around fittings and connections indicate a
leak.
3. If a leak appears, turn off supply line gas shut-off valve
and tighten connections.
4. Retest for leaks by turning on the supply line gas shutoff
valve. When leak check is complete (no bubbles
appear), test is complete.
5. Wipe off all soap solution or detection fluid residue.
Important Notes for Gas Connection:
– The appliance and its individual gas shutoff valve
must be disconnected from the gas supply piping
system during any pressure testing of that system at
test pressures in excess of 1/2psi (3.5kPa).
– The appliance must be isolated from the gas supply
piping system by closing its individual manual shut-off
valve during any pressure testing of the gas supply
piping system at test pressures equal to or less than
1/2psi (3.5kPa).
3.6 Install appliance
WARNING
TIP OVER HAZARD! A child or adult can tip the range
over and be killed.
▶Install the anti-tip device to the structure and/or the
range.
▶Verify the anti-tip device has been properly installed and
engaged.
▶Engage the range to the anti-tip device. Ensure the anti-
tip device is re-engaged when the range is moved.
▶Re-engage the anti-tip device if the range is moved. Do
not operate the range without the anti-tip device in place
and engaged.
▶See installation instructions for details.
▶Failure to follow the instructions in this manual can
result in death or serious burns to children and adults.
▶Check for proper installation and use of the anti-tip
bracket. Carefully tip the range forward pulling from the
back to ensure that the anti-tip bracket engages the
range leg and prevents tip-over. The range should not
move more than 1" (2.5cm).
3.7 Installing the anti-tip bracket
1. Ensure that the electrical connection and the gas
connection are in the correct position.
2. Assemble the bracket.
3. Align the base of the hook of the bracket with the base
on the slot of the rear wall fastening bracket. Align the
base of the fastening bracket with the ground and
tighten the screws to fix the measurements.
4. For wall mounting, proceed with steps 5–7 and 10. For
floor mounting, proceed with steps 8–9 and 10.
en-us Installation procedure
18
5. Use the specified distance from the side of the
appliance to the bracket holes.
6. Move the bracket onto the wall and fix with the two
washers and screws. A qualified technician must verify
suitability of the materials in accordance with the type
and condition of the wall.
7. Use the following distances for the distance from the
side of the appliance to the bracket holes.
8. After having positioned and leveled the appliance, move
the bracket close to the rear of the appliance and
anchor it to the floor with the two washers and screws.
A qualified technician must verify suitability of the
materials in accordance with the type and condition of
the floor.
9. Push the cooker towards the wall, and at the same time,
insert the bracket in the plate fastened to the rear of the
appliance.
10. WARNING The rear vent trim has 3/16” (5mm)
standoffs to keep the appliance slightly off of the back
wall. Do not remove or tamper with standoffs due to
potential temperature issues.
Check for proper installation and use of the anti-tip
bracket. Carefully tip the range forward pulling from the
back to ensure that the anti-tip bracket engages the
range leg and prevents tip-over. The range should not
move more than 1” (2.5cm).
Installation procedure en-us
19
3.8 Connect electrical supply
This dual-fuel range may be connected using an electric
range cord or using a flexible conduit electrical connection.
The length must be at least 5ft (1.5m).
For technical specifications see the rating label on the
underside of the projecting control panel.
a
Do not use multiple outlets, extension cords or adapters.
Note
¡In Canada, the range is shipped from the factory with
the power cord already installed.
¡We recommend that only qualified persons add a power
cord or make electrical connections to this appliance.
For installations other than those in Canada, connect the
power cord at the terminal block. Access the terminal
block by removing the cover in the lower right-hand corner
of the range back panel.
WARNING
ELECTRICAL GROUNDING INSTRUCTIONS
▶This appliance (HDS8..5C) is equipped with a four-
prong grounding plug for your protection against shock
hazard and should be plugged directly into a properly
grounded receptacle. Do not cut or remove the
grounding prong from this plug.
3.9 Preparation for power connection
WARNING
Risk of Electric Shock or Fire. Grounding through the
neutral conductor is prohibited for new branch-circuit
installations (1996 NEC), mobile homes, and recreational
vehicles, or in an area where local codes prohibit
grounding through the neutral conductor.
For installations where grounding through the neutral
conductor is prohibited: (a) disconnect the link from the
neutral, (b) use grounding terminal or lead to ground unit,
(c) connect neutral terminal to lead branch circuit neutral
in the usual manner. When the appliance is to be
connected by means of a cord kit, use 4-conductor cord
for this purpose.
Use only cord kits rated 208/240volts, 50amperes, with
ring or fork type connector and labelled "For use with
ranges”. Use only flexible conduit with wires with ring or
fork type connectors. Strain relief provided with the cord
must be installed per instructions included with the cord.
The nuts for supply cable fixing come separately in an
accessory bag.
3-Wire Hookup
R Red
W White
GS Grounding Strip
B Black
4-Wire Hookup
R Red
W White
G Green
B Black
en-us Installation procedure
20
WARNING
To prevent electrical shock, the grounding prong on the
range cord should not be cut or removed under any
circumstances.
▶It must be plugged into a matching grounding type
receptacle and connected to a correctly polarized 240-
Volt circuit.
▶If there is any doubt as to whether the wall receptacle is
properly grounded, have it checked by a qualified
electrician.
3.10 Four-wire range cord connection
(recommended method)
1. Disconnect the electrical power at the breaker box.
Remove the terminal block cover to expose the terminal
block.
2. If you need a lager hole for the strain relief (not provided
with range) remove the metal plate. Rotate it 180° to
have the lager hole for the power supply cable and
mount it again.
3. Insert the power supply cable into the terminal block
through the bottom hole.
4. Mount strain relief (not provided with range) through the
hole of the metal plate in the back panel located below
the terminal block and secure tightly. Route the wires of
the power supply cable through the strain relief and
tighten clamp.
Make sure the strain relief is secured properly.
5. Remove the grounding strap from the center post on the
terminal block. Therefore remove the hexagonal nut of
the neutral pin. Remove the fork type connector of the
groundling link. Mount the hexagonal nut on the neutral
pin again. Remove the green hexagonal screw and the
ring connector from the grounding. The strap will not be
needed. Remove it from the unit.
6. Attach the insulated grounding wire to the grounding
hole with the green grounding screw. Tighten the green
hexagonal screw firmly, but do not overtighten.
7. Insert the flat washer.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
Bosch HDS8045U Guide d'installation
- Catégorie
- Cuisinières
- Taper
- Guide d'installation
dans d''autres langues
- English: Bosch HDS8045U Installation guide