Modern Forms FR-W1811 Aviator Mode d'emploi

Marque: Modern Forms

Modèle: FR-W1811 Aviator

Catégorie: Ventilateurs ménagers

Taper: Mode d'emploi

Aviator

Installation Instructions

works with the

Google Assistant

FR-W1811

Aviator Instructions2

Please read and

save these instructions

before installation

DO NOT RETURN TO STORE

FR-W1811Aviator Instructions 3

For all questions about your ceiling fan please read all included

instructions, installation procedures, troubleshooting guidelines

and warranty information before starting installation.

For missing parts or general inquiries call our trained technical staﬀ at:

1-866-810-6615 option 1

MON-FRI 8AM-8PM EST

Email: customerservice@modernforms.com

Or live chat at modernforms.com

For fast service have the following information below when you call:

1. Model Name and Number

2. Part Number and Part Description

3. Date Of Purchase and Purchase Location

1-866-810-6615 option 2

MON-FRI 8AM-8PM EST

Email: fansupport@modernforms.com

General Inquiries

Fan Support

FR-W1811

Aviator Instructions4

For operation, maintenance, and troubleshooting information,

visit http://modernforms.com/fan-support/

To reduce the risk of electric shock, ensure electricity has been turned oﬀ at the circuit breaker

before beginning. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA

70” and local electrical codes. Electrical installation should be performed by a licensed electrician.

The fan must be mounted with a minimum of 7 ft. (2.1m) clearance from the trailing edge of

the fan blades to the floor and a minimum of 1.5 ft (0.5m) from the edge of the fan blades to the

surrounding walls. Never place objects in the path of the fan blades. To avoid personal injury or

damage to the fan and other items, please be cautious when working around or cleaning the fan.

To avoid electrical shock or damage to the motor or ﬁnish, do not use water or chemicals

when cleaning the fan or fan blades. A dry cloth or lightly dampened cloth will be suitable

for most cleaning.

After making electrical connections, spliced conductors should be turned upward and pushed

carefully up into the outlet box. The wires should be spread apart with the grounded conductor and

the equipment-grounding conductor on one side of the outlet box, and the ungrounded conductor

on the other side of the outlet box.

All set screws must be checked and re-tightened

where necessary before installation.

Safety Rules

FR-W1811 Aviator Instructions 5

WARNING: Do not install or use your fan if any part(s) is/are damaged or missing. This product

is designed for use only with the supplied parts and/or accessories designated for use with this

product by Modern Forms. Substitution of parts or accessories not designated for use with this

product by Modern Forms could result in personal injury or property damage and will void the

warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.

WARNING: To reduce the risk of electric shock, this fan must

be installed and operated with the supplied wall control, or controlled from the Modern Forms app.

WARNING: Do not use power tools to assemble or install your fan. Using power tools can result in

improper assembly which can lead to noise or fan damage,personal injury or property damage.

WARNING: To reduce the risk of personal injury, do not bend the blade arms when installing the

brackets, balancing the blades or cleaning the fan.

WARNING: Do not insert foreign objects between rotating fan blades.

WARNING: Do not operate fan unless fan blades are in place. Noise and fan damage can occur

WARNING: This appliance is not intended for use by young children without supervision.

WARNING: To reduce the risk of ﬁre, electric shock, personal injury or damage to the fan or other

items, the outlet box and support structure must be securely mounted and capable of reliably

supporting a minimum of 35 Ibs (15.9 kg). Use only UL/cUL listed outlet boxes marked “FOR FAN

SUPPORT.” Use only the screws and washers provided with the outlet box.

CAUTION: Before assembling your fan, refer to the “Making the Electrical Connections“

section. If you feel you do not have enough wiring knowledge or experience, have your fan

installed by a licensed electrician.

NOTE: Before servicing or cleaning the fan, switch power oﬀ at the circuit breaker.

FR-W1811

Aviator Instructions6

Integrates

seamlessly with:

devices you already own

works with the

Google Assistant

Get Smart...

Premium smart

features:

Accessories:

MOTOR

complement high quality materials

personalize your experience

Quiet, reliable, and up to 70%

PRUHHɝFLHQWWKDQ$&IDQV

:L)LDQG%OXHWRRWKHQDEOHG

IRUȵH[LEOHFRQWURO

%OXHWRRWK:DOO&RQWURO

'LPVOLJKWWR_212))

IDQVSHHGV_6ROGVHSDUDWHO\

F-WCBT-WT :KLWH

%OXHWRRWK5HPRWH&RQWURO

'LPVOLJKWWR_212))

IDQVSHHGV

F-RCBT-WT :KLWH

Wet Location-listed to the strictest

UL/cUL safety regulations. Finished

and rated for interior and exterior use

FR-W1811 Aviator Instructions 7

1. Mounting Options 10

2. Hanging the Fan 12

3. Making the Electrical Connections 14

4. Installing the Wall Control 16

5. Attaching the Fan Blades 18

6. Attaching Decorative Lower Cap 18

7. Finishing the Installation 18

8. Installing the Optional LED Luminaire Module 20

9. Controlling the Fan 22

10. Reset 24

11. Breeze Mode 24

12. Application 24

13. Accessories 26

14. Troubleshooting 28-30

Contents

Tools Required

FR-W1811

Aviator Instructions8

** denotes ﬁnish code of fan

Package Contents

5. Motor Assembly

6. Blade Collector Ring

7. Lower Cover Bottom Cap

RPL-F1811-54-CA-**

8. Control Receiver

w/ Wire Nuts/Ties

F-R3-1811-054

9. Remote Control

F-RCBT-WT

Hardware Bag

RPL-AVIATOR-PARTS

1. Blade Set of 3

RPL-F1811-54-BD-**

2. Hanger Assembly

Mounting Bracket

Downrod Assembly

RPL-HGR-ASM-**

3. Canopy w/Canopy Ring

RPL-CAN-CYL-**

4. Coupling Cover

Before discarding packaging materials be certain all parts have been removed.

Place the parts from the hardware bag into a small container to keep them from being lost.

• Part A

• Part B

• Part C

• Part D

• Part E

Hardware Bag

RPL-AVIATOR-PARTS

#10 x 38mm Pan Head Phillip Screws (2)

#10x76mm Pan Head Phillip Wood Screws (1)

1/4”x16mm Phil/Slotted Pan Head Screw (7)

3/16”( 5.2x8.4x1.0mm) Spring Washer (1)

6.5x19x2mm Flat Washer (1)

3/16” Star Washer (2)

4*9 Flat Head Customed Philips Screw (10)

5 x 14 x 1mm Flat Washer (2)

D: Blade

C: Wire Nuts

B: Safety Cable

E: Attach The Blade Collector Ring

To Blade

(Found with the receiver)

FR-W1811 Aviator Instructions 9

IMPORTANT: Please make note

of the MAC ID on the

receiver and keep it in a

safe place.

MAC ID

Hanging Weight: OEV

E: Attach The Blade Collector Ring

To Blade

FR-W1811

Aviator Instructions10

1. Mounting Options

CAUTION: To prevent electrical shock, ensure electricity has been

turned oﬀ at the circuit breaker before beginning.

If there isn’t an existing UL/cUL listed outlet box, please refer to the

following instructions. Secure the outlet box directly to the building

structure. Use appropriate fasteners and building materials. The

outlet box and support structure must be able to fully support the

moving weight of the fan (at least 35 lbs/15.9 kg). Do not use plastic

outlet boxes. Use only UL/cUL listed outlet boxes marked

“FOR FAN SUPPORT.”

Secure the outlet box directly to the building structure.

Use Part A if needed to mount your outlet box.

Figures 1-1C are examples of diﬀerent ways to mount the

outlet box.

NOTE: To hang your fan where there is an existing ﬁxture but no

ceiling joist, you may need an installation hanger bar.

NOTE: Downrod fans can be suspended up to a maximum

recommended length of 72” using additional downrods

(sold separately) and the included 80” lead wire.

NOTE: The sloped ceiling kit (sold separately) is required for sloped

ceiling applications, and will accommodate slopes up to 45° (Fig. 1B).

NOTE: You may need a longer downrod to maintain proper blade

clearance when installing on a steep, sloped ceiling (Fig. 1B).

FR-W1811 Aviator Instructions 11

1. Support Brace

2. Outlet Box

3. Joist

1. Support Brace

2. Mounting Bracket

3. Recess Outlet Box

1. Outlet Box

Support Ceiling

Max 30° Angle

FR-W1811

Aviator Instructions12

2. Hanging the Fan

1. Disconnect power at the breaker to the fan location.

A licensed electrician must install the fan.

2. Remove 1 of 2 screws from the bottom of mounting bracket and

save for use in the Finishing the Installation section. Loosen the

other screw (Fig. 2).

3. Pass the 120-volt supply wires through the center hole in the

ceiling mounting bracket as shown in (Fig. 2).

4. Secure the mounting bracket to the ceiling outlet box with the

screws and washers provided with your outlet box (Fig. 2).

5. Remove the clevis pin and cotter pin and loosen the two collar

screws from the motor collar (Fig. 2).

6. Feed motor wires through coupling cover, canopy ring, and canopy.

7. Feed motor wire through downrod assembly.

8. Thread the downrod assembly onto motor collar. Align the holes

of downrod and collar and insert the cotter pin and clevis pin.

Tighten the two collar screws (Fig. 2).

9. Carefully lift the fan motor assembly up to the mounting

bracket and seat the hanger ball in the mounting bracket

socket. Make sure the tab on the mounting bracket socket is

properly seated in the groove in the hanger ball (Fig. 2A).

Rotate the socket assembly until the ball drops and locks

into the hanger bracket screw.

10. Secure the safety cable to the building structure using spring

washer, flat washer, and wood screw provided (Fig. 2B) Use Part B.

NOTE: Safety cable is required for all installations in Canada. Safety

cable is required for ceiling fan and light combinations over 35 lbs.

in both flush and downrod models in the United States.

WARNING: Failure to properly install the cotter pin and/or

tighten the screws could result in the fan loosening and

possibly falling.

FR-W1811 Aviator Instructions 13

1. Hanger Ball/

Mounting Bracket

2. Downrod

3. Canopy

4. Canopy Ring

5. Coupling Cover

6. Collar

7. Cotter Pin

8. Clevis Pin

9. Screws

2A 2B

FR-W1811

Aviator Instructions14

3. Making the Electrical Connections

WARNING: Installation of this fan requires that a three-conductor

cable (including ground wire) which should run between ceiling and

wall outlet box.

WARNING: Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire nuts,

except for the ground wire.

Insert the receiver into the motor assembly with the flat side of the

receiver facing the ceiling (Fig. 6).

Motor to Receiver & Receiver to house supply wires (Fig. 6A).

1. Connect the motor assembly ground wire, mounting bracket

ground wire and receiver ground wire to the ground wire in

outlet box. Use Part C.

WARNING: Failure to connect ground wires could result in

poor fan control functionality. Failure to make proper color-coded

connections may result in permanent damage to the receiver

2. Connect the red wire from the fan to the red wire marked

“TO MOTOR” from the receiver.

3. Connect the grey wire from the fan to the grey wire marked

“TO MOTOR” from the receiver.

4. Connect the yellow wire from the fan to the yellow wire marked

“TO MOTOR” from the receiver.

5. Connect the white wire from the fan to the white wire marked

“FOR LIGHT” from the receiver.

6. Connect the blue wire from the fan to the blue wire marked

“FOR LIGHT” from the receiver.

7. Connect the black (hot) wire from the ceiling to the black wire

marked “AC in L” from the receiver.

8. Connect the white (neutral) wire from the ceiling to the white

wire marked “AC in N” from the receiver.

NOTE: If you are not installing the optional luminaire module - cap oﬀ

white wires marked “FOR LIGHT” and blue wires marked “FOR LIGHT”

from receiver and corresponding wires from fan with wire nuts and

electrical tape. Failure to do so may result in permanent damage to

the receiver.

FR-W1811 Aviator Instructions 15

Follow the steps below to connect the fan to your household wiring. Use the plastic wire nuts with your fan.

Secure the plastic wire nuts with electrical tape. Make sure there are no loose strands or connections.

1. Mounting Bracket

2. Receiver

Black(Hot)

can be RED from Switch leg

Black(Line in H)

RED(to Motor)

GREEN(Ground)

BLUE (to Light)

BLUE (for Light)

GREEN(GND Must Use)

GREEN(Hanger Bracket Ground)

RED(to Motor)

GREY(to Motor)

WHITE(Neutral)

WHITE(to Light)

WHITE(Neutral)

Safety Cable

GREY(to Motor)

YELLOW(to Motor)

WHITE(Line in N)

YELLOW(to Motor)

Outlet

Box

Receiver

Hanger Ball & Downrod

Hanger

Bracket

FR-W1811

Aviator Instructions16

4. Installing the Optional Wall Control

NOTE: Wall Control is not included. A bluetooth wall control

accessory can be purchased separately.

1. Connect the green wire marked “GROUND” from the wall

control to the copper wire from the wall outlet box that

feeds back to the circuit breaker – important for proper

fan function (Fig. 4).

2. Connect the black wire marked “LINE IN” from the wall control to

the black LINE VOLTAGE wire from the wall

outlet box that feeds back to the circuit breaker (Fig. 4).

3. Connect the red wire from the wall control to the black wire from

the wall outlet box that feeds up to the fan (Fig. 4).

4. Connect the white wire from the wall control to the white

(neutral) wire from the wall outlet box (Fig. 4).

5. Carefully tuck the wire connections inside the outlet box.

Secure the wall control with the two (2) wall control screws

provided (Fig. 4A).

6. Attach the wall mounting plate over the wall switch and secure

with the two (2) wall mounting plate screws provided (Fig. 4A).

7. Fasten the wall plate to the wall mounting plate (Fig. 4A).

Wall Switch WiresHouse Wires

(Hot In)

(Neutral)

(Ground)

(Hot out to Fan)

Fan Switch leg

(Copper/Ground)

(Neutral)

(Hot)

to Fan

From Breaker

* Home Wiring may vary

FR-W1811 Aviator Instructions 17

Multi-location wiring

1 2 3

1. Wall Outlet

2. Wall Control

3. Wall Mounting Plate

4. Mounting Plate Screws

5. Wallplate

Individually pair each of the wall controls with the fan

receiver using the pairing instruction. See page 22.

Line/Hot

Red

Green (Green or Bare)

Wall Control 1 Wall Control 2 Wall Control 3

If Applicable

FAN

Neutral/White

FR-W1811

Aviator Instructions18

7. Finishing the Installation

1. Secure all wire connections with supplied wire ties to assist in

canopy installation.

2. Tuck connections neatly into ceiling outlet box.

3. Slide the canopy up to hanger bracket and place the key hole on

the canopy over the screw on the hanger bracket. Turn canopy

until it locks in place at the narrow section of the key holes (Fig. 7).

4. Align the circular hole on canopy with the remaining hole on the

hanger bracket. Secure by tightening the one screw previously

loosened and the one previously removed.

5. Adjust the canopy screws as necessary until the canopy and

canopy cover are snug.

WARNING: Make sure tab at bottom of hanger bracket is properly

seated in groove of hanger ball before attaching canopy to bracket.

Failure to properly seat tab in groove could cause damage to electrical

wiring.

1. Place fan blade on motor as shown (Fig. 5) and secure with the

blade attachment screws. Use Part D.

2. Secure the bottom of the fan blades together using the provided

blade collector ring and hardware (Fig. 5A). Use Part E.

1. Tightly twist the decorative lower cap onto

the motor assembly (Fig. 6).

5. Attaching the Fan Blades

6. Attaching Decorative Lower Cap

FR-W1811 Aviator Instructions 19

5 5A

FR-W1811

Aviator Instructions20

8. Installing the Optional LED Luminaire Module

WARNING: Before starting installation, disconnect the power

by turning oﬀ the circuit breaker or removing the fuse at fuse box.

1. Unthread and remove the decorative lower cap from the motor

assembly (Fig. 8).

2. Remove the 3 screws from the wire housing lower cover and keep

them for use with the light kit adapter plate. Remove the wire housing

lower cover (Fig. 8-8A).

3. Install light kit adapter plate to the mounting ring using the 3 screws

previously removed.

4. Raise and hold the LED luminaire module close to the adapter plate

and proceed to secure the wire connections. Connect the white wire

connector from the LED luminaire module to the white wire of the

fan. Follow the same procedure with the black wire connector. Tuck

connections neatly into adapter plate. Using the 3 screws provided,

install the LED luminaire module to the adapter plate (Fig. 8B).

5. Raise glass shade up against the luminaire module, and

secure it to fan by turning acrylic shade clockwise until snug.

Do not overtighten (Fig. 8C).

LED Luminaire Installation

(F-1811-LED-**) Sold separately

La page charge ...

Modern Forms FR-W1811 Aviator Mode d'emploi

Marque: Modern Forms

Modèle: FR-W1811 Aviator

Catégorie: Ventilateurs ménagers

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Modern Forms FR-W1811 Aviator Operating instructions

Modern Forms FR-W1811 Aviator Mode d'emploi

Modern Forms FR-W1811 Aviator Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents