Chief CMA474 Le manuel du propriétaire
- Catégorie
- Mur
- Taper
- Le manuel du propriétaire
CMA474 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all mounts/accessories
are properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this accessory can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this accessory is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
accessory.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located within the CMA474 does not exceed
35 lbs (15.9 kg), less the weight of the projector attached to
the SYSAU suspended ceiling projector mount.
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: For indoor use only.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: All wiring should be performed by a licensed
electrician following all local codes and ordinances.
WARNING: For A/V or ITE components to be installed and
powered within the enclosure, it is necessary to provide and
indicate the location of a readily accessible and operable
disconnect device.
IMPORTANT ! :
The CMA474 accessory is designed to be
mounted to the Chief SYSAU suspended ceiling projector
mounting system ONLY.
IMPORTANT ! : The CMA474 has been designed to support
a single duplex electrical receptacle.
NOTE: It is the installer’s responsibility to ensure that the
enclosure is bonded to the ground in the switch box, in
accordance with the National Electric Code, ANSI/NFPA 70 or
Canadian Electrical Code, CSA C22.1. Two green grounding
screws are included for installation in the enclosure for the
purpose, if required.
NOTE: Spacings - To ensure safe operation of the equipment
installed in the enclosure, per National Electric Code, ANSI/
NFPA 70, a minimum separation between power cords and
signal or communication cables may be required.
NOTE: This Cabinet System is for use with Listed ITE or Audio/
Visual equipment only.
NOTE: Knockouts are provided for ease of installation. Any
open knockout needs to be plugged.
NOTE: When selecting a Listed 120 Vac Receptacle for use as
the main power source for the CMA474 box (to power the A/V
equipment), make sure that AC Receptacle is rated at least 15A
and it is used in the building’s AC branch circuit that is connected
to a circuit breaker rated at least 15A. Do not connect more than
12A from the 15A Receptacle, or 16A from the 20A Receptacle.
In the U.S., the equipment shall be installed per the applicable
requirements of the National Electrical Code, ANSI/NFPA 70.
In Canada, the equipment shall be installed per the applicable
requirements of the Canadian Electrical Code, CSA C22.1.
--SAVE THESE INSTRUCTIONS--
Installation Instructions CMA474
3
DIMENSIONS
0.875
CONDUIT PASS
THROUGH
6X
1.734
1 1/2" TRADE SIZE
KNOCKOUT
6X 1.375
1" TRADE SIZE
KNOCKOUT
6X 0.875
1/2" TRADE SIZE
KNOCKOUT
NOTE:
CEILING PLATE IS SHOWN FOR REFERENCE ONLY.1.
DIMENSIONS: INCHES
[MILLIMETERS]
CMA474 Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions CMA474
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
A (1)
[Cover-left]
B (1)
[Cover-right] C (2)
[Box end]
D (1)
[Box body-left] E (1)
[Box body-right]
F (14)
10-24 x 3/8"
J (6)
G (6)
10-16 x 1/2"
H (6)
#10 10-24 x 3/8"
K (2)
10-32
(grounding screw)
CMA474 Installation Instructions
6
ASSEMBLY
1. Loosely install three 10-24 x 3/8" Phillips pan head screws
with external teeth (F) into the top edge of the box body-left
(D). (See Figure 1)
2. Loosely install three 10-24 x 3/8" Phillips pan head screws
with external teeth (F) into the side edge of the box body-left
(D). (See Figure 1)
Figure 1
3. Install one grounding screw (K) into box body-right (E) and
-left (D). (See Figure 1) and (See Figure 2)
4. Loosely install two 10-24 x 3/8" Phillips pan head screws
with external teeth (F) into the top edge of the box body-right
(E). (See Figure 2)
5. Loosely install two 10-24 x 3/8" Phillips pan head screws
with external teeth (F) into the side edge of the box body-
right (E). (See Figure 2)
Figure 2
INSTALLATION
1. Lower box body-left (D) onto SYSAU ceiling projector
mount (not included). (See Figure NOTE:)
2. Attach box body to SYSAU ceiling plate using four
10-24 x 3/8" Phillips pan tapping screws (J) through four #10
lock washers (H). (See Figure NOTE:)
NOTE: Use the Phillips pan self-drilling screws (G) if not using
the pre-drilled holes when attaching the box body.
Figure 3
3. Lower box body-right (E) onto SYSAU ceiling plate (not
included). (See Figure 4)
4. Attach box body to SYSAU ceiling plate using two
10-24 x 3/8" Phillips pan tapping screws (J) through two #10
lock washers (H). (See Figure 4)
NOTE: Use the Phillips pan self-drilling screws (G) if not using
the pre-drilled holes when attaching the box body.
Figure 4
1
(F) x 3
2
(F) x 3
(D)
(K)
3
4
(F) x 2
5
(F) x 2
(E)
(K)
3
1
(J) x 4
2
(H) x 4
(D)
SYSAU
ceiling plate
(J) x 2
4
(H) x 2
(E)
3
Installation Instructions CMA474
7
5. Add components to CMA474, as necessary.
6. Fasten one box end (C) to each end of the CMA474 using
two 10-24 x 3/8" Phillips pan head with external teeth (F) on
each box end. (See Figure 5)
Figure 5
7. Lower cover-right (B) over box body-right (E) and place over
Phillips screws fastened into box body lower and upper
edges. (See Figure 6)
8. Slide cover to securely fasten over Phillips screws. (See
Figure 6)
Figure 6
9. Lower cover-left (A) over box body-left (D) and place over
Phillips screws fastened into box body lower and upper
edges. (See Figure 7)
10. Slide cover to securely fasten over Phillips screws. (See
Figure 7)
Figure 7
Adjustments
1. The CMA474 may adjust in length, as required.
(See Figure 8)
2. The CMA474 may also be located in various
locations on the SYSAU ceiling plate. (See Figure 8)
NOTE: Use the Phillips pan head self-drilling screws (G) when
attaching the box body (left or right) to the SYSAU
ceiling plate in a location other than at pre-drilled holes.
Figure 8
(C)
(C)
(F) x 2
6
Installed
box end
7
7
8
(B)
(E)
9
9
10
(A)
(D)
1
2
SYSAU ceiling plate
CMA474 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-002805 Rev01
2016 Milestone AV Technologies
www.chiefmfg.com
02/16
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief CMA474 Le manuel du propriétaire
- Catégorie
- Mur
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: Chief CMA474 Owner's manual