Smeg S3F092P Manuel utilisateur

Catégorie
Congélateurs
Taper
Manuel utilisateur
S3F092P
User Manual
Freezer
Notice d'utili‐
sation
Congélateur
Benutzerin‐
formation
Gefriergerät
CONTENTS
Safety information 2
Safety instructions 3
Operation 5
First use 6
Daily Use 6
Hints and tips 7
Care and cleaning 7
Troubleshooting 9
Installation 11
Technical information 15
Subject to change without notice.
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read
the supplied instructions. The manufacturer is not responsible
if an incorrect installation and use causes injuries and
damages. Always keep the instructions with the appliance for
future reference.
Children and vulnerable people safety
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved.
Do not let children play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
Keep all packaging away from children.
General Safety
This appliance is intended to be used in household and
similar applications such as:
Farm houses; staff kitchen areas in shops, offices and
other working environments
By clients in hotels, motels, bed and breakfast and other
residential type environments
Keep ventilation openings, in the appliance enclosure or in
the built-in structure, clear of obstruction.
2
Do not use mechanical devices or other means to accelerate
the defrosting process, other than those recommended by
the manufacturer.
Do not damage the refrigerant circuit.
Do not use electrical appliances inside the food storage
compartments of the appliance, unless they are of the type
recommended by the manufacturer.
Do not use water spray and steam to clean the appliance.
Clean the appliance with a moist soft cloth. Only use neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
Do not store explosive substances such as aerosol cans
with a flammable propellant in this appliance.
If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
SAFETY INSTRUCTIONS
Installation
WARNING! Only a qualified
person must install this
appliance.
Remove all the packaging.
Do not install or use a damaged
appliance.
Obey the installation instruction supplied
with the appliance.
Always be careful when you move the
appliance because it is heavy. Always
wear safety gloves.
Make sure the air can circulate around
the appliance.
Wait at least 4 hours before connecting
the appliance to the power supply. This
is to allow the oil to flow back in the
compressor.
Do not install the appliance close to
radiators or cookers, oven or hobs.
The rear of the appliance must stand
against the wall.
Do not install the appliance where there
is direct sunlight.
Do not install this appliance in areas that
are too humid or too colds, such as the
construction appendices, garages or
wine cellars.
When you move the appliance, lift it by
the front edge to avoid scratching the
floor.
Electrical connection
WARNING! Risk of fire and
electrical shock.
The appliance must be earthed.
Make sure that the electrical information
on the rating plate agrees with the
power supply. If not, contact an
electrician.
Always use a correctly installed
shockproof socket.
Do not use multi-plug adapters and
extension cables.
Make sure not to cause damage to the
electrical components (e.g. mains plug,
mains cable, compressor). Contact the
Authorised Service Centre or an
3
electrician to change the electrical
components.
The mains cable must stay below the
level of the mains plug.
Connect the mains plug to the mains
socket only at the end of the installation.
Make sure that there is access to the
mains plug after the installation.
Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
Use
WARNING! Risk of injury,
burns, electrical shock or fire.
Do not change the specification of this
appliance.
Do not put electrical appliances (e.g. ice
cream makers) in the appliance unless
they are stated applicable by the
manufacturer.
Be careful not to cause damage to the
refrigerant circuit. It contains isobutane
(R600a), a natural gas with a high level of
environmental compatibility. This gas is
flammable.
If damage occurs to the refrigerant
circuit, make sure that there are no
flames and sources of ignition in the
room. Ventilate the room.
Do not let hot items to touch the plastic
parts of the appliance.
Do not put soft drinks in the freezer
compartment. This will create pressure
on the drink container.
Do not store flammable gas and liquid in
the appliance.
Do not put flammable products or items
that are wet with flammable products in,
near or on the appliance.
Do not touch the compressor or the
condenser. They are hot.
Do not remove or touch items from the
freezer compartment if your hands are
wet or damp.
Do not freeze again food that has been
thawed.
Obey the storage instructions on the
packaging of frozen food.
Care and cleaning
WARNING! Risk of injury or
damage to the appliance.
Before maintenance, deactivate the
appliance and disconnect the mains
plug from the mains socket.
This appliance contains hydrocarbons in
the cooling unit. Only a qualified person
must do the maintenance and the
recharging of the unit.
Regularly examine the drain of the
appliance and if necessary, clean it. If
the drain is blocked, defrosted water
collects in the bottom of the appliance.
Disposal
WARNING! Risk of injury or
suffocation.
Disconnect the appliance from the mains
supply.
Cut off the mains cable and discard it.
Remove the door to prevent children
and pets to be closed inside of the
appliance.
The refrigerant circuit and the insulation
materials of this appliance are ozone-
friendly.
The insulation foam contains flammable
gas. Contact your municipal authority for
information on how to discard the
appliance correctly.
Do not cause damage to the part of the
cooling unit that is near the heat
exchanger.
4
OPERATION
Control panel
1 2 3 4 5
1
Pilot light
2
Temperature regulator
3
Super light
4
Super switch and Alarm reset switch
5
Alarm light
Switching on
Insert the plug into the wall socket
Turn the Temperature regulator
clockwise to a medium setting.
The pilot light will light up
If the temperature inside the appliance is
too high the Alarm light will blink. Active the
Super function.
Switching off
To turn off the appliance, turn the
Temperature regulator to the "O" position.
The pilot light will switch off.
Temperature regulation
The temperature is automatically regulated.
To operate the appliance, proceed as
follows:
turn the temperature regulator
toward lower settings to obtain the
minimum coldness.
turn the temperature regulator
toward higher settings to obtain the
maximum coldness.
A medium setting is generally
the most suitable.
However, the exact setting
should be chosen keeping in
mind that the temperature inside
the appliance depends on:
room temperature
how often the door is
opened
the quantity of food
stored
the location of the
appliance.
Super function
You can activate the Super function by
pressing the Super switch.
TheSuper light will light up.
This function stops automatically
after 52 hours.
It is possible to deactivate the
function at any time by pressing
Super switch.
The Super light will switch off.
High temperature alarm
An increase in the temperature in a
compartment (for example due to an power
failure) is indicated by flashing of the Alarm
light.
5
When normal conditions are restored the
Alarm light will switch off automatically.
FIRST USE
Cleaning the interior
Before using the appliance for the first time,
the interior and all internal accessories
should be washed with lukewarm water
and some neutral soap to remove the
typical smell of a brand-new product, then
dried thoroughly.
CAUTION! Do not use
detergents or abrasive powders,
as these will damage the finish.
DAILY USE
Freezing fresh food
The freezer compartment is suitable for
freezing fresh food and storing frozen and
deep-frozen food for a long time.
To freeze small amount of fresh foods it is
not necessary to change the present
setting.
To freeze fresh food activate the Super
function at least 24 hours before placing the
food to be frozen in the freezer
compartment.
Place the food to be frozen in the two top
compartments.
The maximum amount of food that can be
frozen in 24 hours is specified on the rating
plate, a label located on the inside of the
appliance.
The freezing process lasts 24 hours: during
this period do not add other food to be
frozen.
When the freezing process is completed,
return to the required temperature (see
"Super Function").
Storage of frozen food
When first starting-up or after a period out
of use, before putting the products in the
compartment let the appliance run at least
2 hours on the higher settings.
In the event of accidental
defrosting, for example due to a
power failure, if the power has
been off for longer than the
value shown in the technical
characteristics chart under
"rising time", the defrosted food
must be consumed quickly or
cooked immediately and then
re-frozen (after cooling).
Ice-cube production
This appliance is equipped with one or
more trays for the production of ice-cubes.
Do not use metallic instruments
to remove the trays from the
freezer.
1.
Fill these trays with water
2.
Put the ice trays in the freezer
compartment.
Thawing
Deep-frozen or frozen food, prior to being
used, can be thawed in the refrigerator
compartment or at room temperature,
depending on the time available for this
operation.
Small pieces may even be cooked still
frozen, directly from the freezer: in this
case, cooking will take longer.
6
HINTS AND TIPS
Normal operating sounds
The following sounds are normal during
operation:
A faint gurgling and bubbling sound from
coils sound when refrigerant is pumped.
A whirring and pulsating sound from the
compressor when refrigerant is pumped.
A sudden cracking noise from inside
appliance caused by thermic dilatation (a
natural and not dangerous physical
phenomenon).
A faint click noise from the temperature
regulator when the compressor switches
on or off.
Hints for energy saving
Do not open the door frequently or leave
it open longer than absolutely necessary.
Hints for freezing
To help you make the most of the freezing
process, here are some important hints:
the maximum quantity of food which can
be frozen in 24 hours is shown on the
rating plate;
the freezing process takes 24 hours no
further food to be frozen should be
added during this period;
freeze only top quality, fresh and
thoroughly cleaned, foodstuffs;
prepare food in small portions to enable
it to be rapidly and completely frozen
and to make it possible subsequently to
thaw only the quantity required;
wrap up the food in aluminium foil or
polythene and make sure that the
packages are airtight;
do not allow fresh, unfrozen food to
touch food which is already frozen, thus
avoiding a rise in temperature of the
latter;
lean foods store better and longer than
fatty ones; salt reduces the storage life
of food;
water ices, if consumed immediately
after removal from the freezer
compartment, can possibly cause the
skin to be freeze burnt;
it is advisable to show the freezing in
date on each individual pack to enable
you to keep tab of the storage time.
Hints for storage of frozen food
To obtain the best performance from this
appliance, you should:
make sure that the commercially frozen
foodstuffs were adequately stored by the
retailer;
be sure that frozen foodstuffs are
transferred from the foodstore to the
freezer in the shortest possible time;
not open the door frequently or leave it
open longer than absolutely necessary;
once defrosted, food deteriorates rapidly
and cannot be refrozen;
do not exceed the storage period
indicated by the food manufacturer.
CARE AND CLEANING
WARNING! Refer to Safety
chapters.
General warnings
CAUTION! Unplug the
appliance before carrying out
any maintenance operation.
This appliance contains
hydrocarbons in its cooling unit;
maintenance and recharging
must therefore only be carried
out by authorized technicians.
The accessories and parts of
the appliance are not suitable for
washing in a dishwasher.
7
Periodic cleaning
CAUTION! Do not pull, move or
damage any pipes and/or
cables inside the cabinet.
CAUTION! Take care of not to
damage the cooling system.
CAUTION! When moving the
cabinet, lift it by the front edge
to avoid scratching the floor.
The equipment has to be cleaned regularly:
1.
Clean the inside and accessories with
lukewarm water and some neutral soap.
2.
Regularly check the door seals and
wipe clean to ensure they are clean and
free from debris.
3.
Rinse and dry thoroughly.
4.
If accessible, clean the condenser and
the compressor at the back of the
appliance with a brush.
This operation will improve the
performance of the appliance and save
electricity consumption.
Defrosting the freezer
CAUTION! Never use sharp
metal tools to scrape off frost
from the evaporator as you
could damage it. Do not use a
mechanical device or any
artificial means to speed up the
thawing process other than
those recommended by the
manufacturer. A temperature
rise of the frozen food packs,
during defrosting, may shorten
their safe storage life.
About 12 hours prior to
defrosting, set a lower
temperature, in order to build up
sufficient chill reserve for the
interruption in operation.
A certain amount of frost will always form
on the freezer shelves and around the top
compartment.
Defrost the freezer when the frost layer
reaches a thickness of about 3-5 mm.
1. Switch off the appliance, or pull out
electrical plug from the wall socket.
2. Remove any stored food, wrap it in
several layers of newspaper and put it in
a cool place.
WARNING! Do not touch
frozen goods with wet
hands. Hands can freeze to
the goods.
3. Leave the door open and insert the
plastic scraper in the appropriate
seating at the bottom centre, placing a
basin underneath to collect the defrost
water.
In order to speed up the defrosting
process, place a pot of warm water in
the freezer compartment. In addition,
remove pieces of ice that break away
before defrosting is complete.
4. When defrosting is completed, dry the
interior thoroughly and keep the scraper
for future use.
5. Switch on the appliance.
After three hours reload the previously
removed food into the freezer
compartment.
8
Periods of non-operation
When the appliance is not in use for long
periods, take the following precautions:
1. Disconnect the appliance from
electricity supply.
2. Remove all food.
3. Defrost (if necessary) and clean the
appliance and all accessories.
4. Leave the door/doors open to prevent
unpleasant smells.
WARNING! If the cabinet will be
kept on, ask somebody to
check it once in a while to
prevent the food inside from
spoiling in case of a power
failure.
TROUBLESHOOTING
WARNING! Refer to Safety
chapters.
What to do if...
Problem Possible cause Solution
The appliance does not oper-
ate.
The appliance is switched
off.
Switch on the appliance.
The mains plug is not con-
nected to the mains socket
correctly.
Connect the mains plug to the
mains socket correctly.
There is no voltage in the
mains socket.
Connect a different electrical
appliance to the mains socket.
Contact a qualified electrician.
The Pilot light flashes The appliance is not work-
ing properly.
Contact a qualified electrician.
The Alarm light flashes The temperature in the
freezer is too high.
Refer to 'High Temperature
Alarm.
The appliance is noisy. The appliance is not sup-
ported properly.
Check if the appliance stands
stable.
The compressor operates
continually.
Temperature is set incor-
rectly.
Refer to "Operation" chapter.
Many food products were
put in at the same time.
Wait some hours and then
check the temperature again.
The room temperature is
too high.
Refer to climate class chart on
the rating plate.
Food products placed in
the appliance were too
warm.
Allow food products to cool to
room temperature before stor-
ing.
The door is not closed cor-
rectly.
Refer to "Closing the door".
9
Problem Possible cause Solution
The Super function is
switched on.
Refer to "Super function".
There is too much frost and
ice.
The door is not closed cor-
rectly or the gasket is de-
formed/dirty.
Refer to "Closing the door".
The water drainage plug is
not correctly positioned.
Position the water drainage
plug in the correct way.
Food products are not
wrapped properly.
Wrap the food products better.
Temperature is set incor-
rectly.
Refer to "Operation" chapter.
The compressor does not
start immediately after press-
ing the Super, or after chang-
ing the temperature.
This is normal, no error has
occurred.
The compressor starts after a
period of time.
Temperature cannot be set. The Super or Intensive-
Cooling function is switch-
ed on.
Switch off Super or Intensive-
Cooling manually, or wait until
the function resets automatical-
ly to set the temperature. Refer
to "Super or IntensiveCooling
function".
The temperature in the appli-
ance is too low/too high.
The temperature regulator
is not set correctly.
Set a higher/lower temperature.
The food products' tem-
perature is too high.
Let the food products tempera-
ture decrease to room temper-
ature before storage.
The thickness of the frost is
greater than 4-5 mm.
Defrost the appliance.
The door has been opened
often.
Open the door only if necessa-
ry.
The Super function is
switched on.
Refer to "Super function".
There is no cold air circula-
tion in the appliance.
Make sure that there is cold air
circulation in the appliance.
If the advice does not lead to
the desired result, contact the
nearest Authorised Service
Centre.
Closing the door
1. Clean the door gaskets.
2. If necessary, adjust the door. Refer to
"Installation".
10
3. If necessary, replace the defective door
gaskets. Contact the Authorised
Service Centre.
INSTALLATION
Positioning
This appliance can be installed in a dry, well
ventilated indoor where the ambient
temperature corresponds to the climate
class indicated on the rating plate of the
appliance:
Cli-
mate
class
Ambient temperature
SN +10°C to + 32°C
N +16°C to + 32°C
ST +16°C to + 38°C
T +16°C to + 43°C
Some functional problems might
occur for some types of models
when operating outside of that
range. The correct operation
can only be guaranteed within
the specified temperature range.
If you have any doubts
regarding where to install the
appliance, please turn to the
vendor, to our customer service
or to the nearest Authorised
Service Centre.
Electrical connection
Before plugging in, ensure that the
voltage and frequency shown on the
rating plate correspond to your domestic
power supply.
The appliance must be earthed. The
power supply cable plug is provided with
a contact for this purpose. If the
domestic power supply socket is not
earthed, connect the appliance to a
separate earth in compliance with
current regulations, consulting a qualified
electrician.
The manufacturer declines all
responsibility if the above safety
precautions are not observed.
This appliance complies with the E.E.C.
Directives.
Ventilation requirements
The airflow behind the appliance must be
sufficient.
5 cm
min.
200 cm
2
min.
200 cm
2
CAUTION! Refer to the
assembly instructions for the
installation.
Door reversibility
The door of the appliance opens to the
right. If you want to open the door to the
left, follow these steps before you install the
appliance:
1. Loosen and remove the upper pin.
11
2. Remove the door.
3. Remove the spacer.
4. With a key, loosen the lower pin.
5.
Tighten the lower pin on the opposite
side.
6. Install the spacer.
7. Install the door.
8. Tighten the upper pin.
Installing the appliance
CAUTION! Make sure that the
mains cable can move freely.
1. If necessary cut the adhesive sealing
strip and then apply it to the appliance
as shown in figure.
x
x
2.
Install the appliance in the niche.
3.
Push the appliance in the direction of
the arrows (1) until the upper gap cover
stops against the kitchen furniture.
1
2
4. Push the appliance in the direction of
the arrows (2) against the cupboard on
the opposite side of the hinge.
5. Adjust the appliance in the niche.
Make sure that the distance between
the appliance and the cupboard front-
edge is 44 mm.
The lower hinge cover (in the
accessories bag) makes sure that the
distance between the appliance and the
kitchen furniture is correct.
Make sure that the clearance between
the appliance and the cupboard is 4
mm.
6. Open the door. Put the lower hinge
cover in position.
12
44mm
4mm
7.
Attach the appliance to the niche with 4
screws.
I
I
8. Remove the correct part from the hinge
cover (E). Make sure to remove the part
DX, in the case of right hinge, SX in
opposite case.
9. Attach the covers (C, D) to the lugs and
the hinge holes.
E
E
B
D
C
10.
Install the vent grille (B).
11.
Attach the hinge covers (E) to the hinge.
12.
Disconnect the parts (Ha), (Hb), (Hc)
and (Hd).
Hb Ha
Hc
Hd
13. Install the part (Ha) on the inner side of
the kitchen furniture.
ca. 50 mm
ca. 50 mm
21 mm
90°
90°
21 mm
14. Push the part (Hc) on the part (Ha).
13
Ha
Hc
15.
Open the appliance door and the
kitchen furniture door at an angle of
90°.
16.
Insert the small square (Hb) into guide
(Ha).
17.
Put together the appliance door and the
furniture door and mark the holes.
Ha
Hb
8 mm
18. Remove the brackets and mark a
distance of 8 mm from the outer edge
of the door where the nail must be fitted
(K).
Ha
K
8 mm
19. Place the small square on the guide
again and fix it with the screws
supplied.
20. Align the kitchen furniture door and the
appliance door by adjusting the part
(Hb).
Hb
21.
Press the part (Hd) on the part (Hb).
Hb
Hd
Do a final check to make sure that:
All screws are tightened.
The sealing strip is attached tightly to the
cabinet.
The door opens and closes correctly.
14
TECHNICAL INFORMATION
Technical data
Height mm 880
Width mm 560
Depth mm 550
Rising time Hours 20
Voltage Volts 230 - 240
Frequency Hz 50
The technical information are situated in the
rating plate, on the external or internal side
of the appliance and in the energy label.
ENVIRONMENT CONCERNS
Recycle the materials with the symbol .
Put the packaging in applicable containers
to recycle it. Help protect the environment
and human health and to recycle waste of
electrical and electronic appliances. Do not
dispose appliances marked with the symbol
with the household waste. Return the
product to your local recycling facility or
contact your municipal office.
15
TABLE DES MATIÈRES
Consignes de sécurité 16
Instructions de sécurité 17
Fonctionnement 19
Première utilisation 20
Utilisation quotidienne 20
Conseils 21
Entretien et nettoyage 22
En cas d'anomalie de fonctionnement 23
Installation 26
Caractéristiques techniques 30
Sous réserve de modifications.
CONSIGNES DE SÉCURITÉ
Avant d'installer et d'utiliser cet appareil, lisez soigneusement
les instructions fournies. Le fabricant ne peut être tenu pour
responsable des dommages et blessures liés à une mauvaise
installation ou utilisation. Conservez toujours cette notice avec
votre appareil pour vous y référer ultérieurement.
Sécurité des enfants et des personnes vulnérables
Cet appareil peut être utilisé par des enfants âgés d'au
moins 8 ans et par des personnes ayant des capacités
physiques, sensorielles ou mentales réduites ou dénuées
d’expérience ou de connaissance, s’ils (si elles) sont
correctement surveillé(e)s ou si des instructions relatives à
l’utilisation de l'appareil en toute sécurité leur ont été
données et si les risques encourus ont été appréhendées.
Les enfants ne doivent pas jouer avec l’appareil.
Le nettoyage et l’entretien par l'usager ne doivent pas être
effectués par des enfants sans surveillance.
Ne laissez pas les emballages à la portée des enfants.
Consignes générales de sécurité
Cet appareil est conçu uniquement pour un usage
domestique et des utilisations telles que :
dans les bâtiments de ferme, dans des cuisines réservées
aux employés dans des magasins, bureaux et autres lieux
de travail ;
pour une utilisation privée, par les clients, dans des hôtels
et autres lieux de séjour.
16
Veillez à ce que les orifices de ventilation, situés dans
l'enceinte de l'appareil ou dans la structure intégrée, ne
soient pas obstrués.
N'utilisez aucun dispositif mécanique ou autre appareil pour
accélérer le processus de dégivrage que ceux
recommandés par le fabricant.
N'endommagez pas le circuit frigorifique.
N'utilisez pas d'appareils électriques à l'intérieur des
compartiments de conservation des aliments de l'appareil,
sauf s'ils sont du type recommandé par le fabricant.
Ne pulvérisez pas d'eau ni de vapeur pour nettoyer
l'appareil.
Nettoyez l'appareil avec un chiffon doux humide. Utilisez
uniquement des produits de nettoyage neutres. N'utilisez
pas de produits abrasifs, de tampons à récurer, de solvants
ni d'objets métalliques.
Ne conservez aucune substance explosive dans cet
appareil, comme des aérosols contenant un produit
inflammable.
Si le câble d'alimentation est endommagé, il doit être
remplacé par le fabricant, son service après-vente ou des
personnes de qualification similaire afin d'éviter un danger.
INSTRUCTIONS DE SÉCURITÉ
Installation
AVERTISSEMENT! L'appareil
doit être installé uniquement par
un professionnel qualifié.
Retirez l'intégralité de l'emballage
N'installez pas et ne branchez pas un
appareil endommagé.
Suivez scrupuleusement les instructions
d'installation fournies avec l'appareil.
Soyez toujours vigilants lorsque vous
déplacez l'appareil car il est lourd.
Portez toujours des gants de sécurité.
Assurez-vous que l'air circule autour de
l'appareil.
Attendez au moins 4 heures avant de
brancher l'appareil sur le secteur. Cela
permet à l'huile de refouler dans le
compresseur.
N'installez pas l'appareil à proximité d'un
radiateur, d'une cuisinière, d'un four ou
d'une table de cuisson.
La surface arrière de l'appareil doit être
positionnée contre un mur.
N'installez pas l'appareil dans un endroit
exposé à la lumière directe du soleil.
N'installez pas l'appareil dans un endroit
trop humide ou trop froid, comme une
dépendance extérieure, un garage ou
une cave.
Lorsque vous déplacez l'appareil, veillez
à le soulever par l'avant pour éviter de
rayer le sol.
17
Connexion électrique
AVERTISSEMENT! Risque
d'incendie ou d'électrocution.
L'appareil doit être relié à la terre.
Vérifiez que les données électriques
figurant sur la plaque signalétique
correspondent à celles de votre réseau.
Si ce n'est pas le cas, contactez un
électricien.
Utilisez toujours une prise de courant de
sécurité correctement installée.
N'utilisez pas d'adaptateurs multiprises
ni de rallonges.
Veillez à ne pas endommager les
composants électriques tels que la fiche
secteur, le câble d'alimentation ou le
compresseur. Contactez le service
après-vente agréé ou un électricien pour
changer les composants électriques.
Le câble d'alimentation doit rester en
dessous du niveau de la fiche secteur.
Ne connectez la fiche d'alimentation
secteur à la prise de courant secteur
qu'à la fin de l'installation. Assurez-vous
que la fiche d'alimentation est accessible
une fois l'appareil installé.
Ne tirez jamais sur le câble
d'alimentation électrique pour
débrancher l'appareil. Tirez toujours sur
la fiche.
Usage
AVERTISSEMENT! Risque de
blessures, de brûlures,
d'électrocution ou d'incendie.
Ne modifiez pas les caractéristiques de
cet appareil.
Ne placez aucun appareil électrique
(sorbetière, etc.) dans l'appareil, en
l'absence d'indications du fabricant.
Veillez à ne pas endommager le circuit
frigorifique. Il contient de l'isobutane
(R600a), un gaz naturel ayant un niveau
élevé de compatibilité environnementale.
Ce gaz est inflammable.
Si le circuit frigorifique est endommagé,
assurez-vous de l'absence de flammes
et de sources d'ignition dans la pièce.
Aérez la pièce.
Évitez tout contact d'éléments chauds
avec les parties en plastique de
l'appareil.
Ne placez jamais de boissons gazeuses
dans le congélateur. Cela engendrerait
une pression sur le récipient de la
boisson.
Ne stockez jamais de gaz ou de liquide
inflammable dans l'appareil.
Ne placez pas de produits inflammables
ou d'éléments imbibés de produits
inflammables à l'intérieur ou à proximité
de l'appareil, ni sur celui-ci.
Ne touchez pas le compresseur ni le
condenseur. Ils sont chauds.
Ne retirez pas et ne touchez pas les
éléments du compartiment congélateur
avec les mains mouillées ou humides.
Ne recongelez jamais un aliment qui a
été décongelé.
Respectez les instructions de stockage
figurant sur l'emballage des aliments
surgelés.
Entretien et nettoyage
AVERTISSEMENT! Risque de
blessure corporelle ou de
dommages matériels.
Avant toute opération d'entretien,
éteignez l'appareil et débranchez la fiche
de la prise secteur.
Cet appareil contient des hydrocarbures
dans son circuit de réfrigération.
L'entretien et la recharge du circuit de
réfrigération doivent être effectués par
un professionnel qualifié.
Examinez régulièrement l'écoulement de
l'appareil et si nécessaire, nettoyez-le. Si
l'orifice est bouché, l'eau provenant du
dégivrage s'écoulera en bas de
l'appareil.
Mise au rebut
AVERTISSEMENT! Risque de
blessure ou d'asphyxie.
Débranchez l'appareil de l'alimentation
électrique.
Coupez le câble d'alimentation et
mettez-le au rebut.
18
Retirez la porte pour empêcher les
enfants et les animaux de s'enfermer
dans l'appareil.
Le circuit frigorifique et les matériaux
d'isolation de cet appareil préservent la
couche d'ozone.
La mousse isolante contient un gaz
inflammable. Contactez votre service
municipal pour obtenir des informations
sur la marche à suivre pour mettre
l'appareil au rebut.
N'endommagez pas la partie du circuit
de réfrigération située à proximité du
condenseur thermique.
FONCTIONNEMENT
Bandeau de commande
1 2 3 4 5
1
Voyant lumineux
2
Thermostat
3
Voyant Super
4
Touche Super et réinitialisation de
l'alarme
5
Voyant d'alarme
Mise en marche
Branchez l'appareil à une prise murale.
Tournez le thermostat vers la droite sur
une position médiane.
Le voyant lumineux s'allume.
Si la température à l'intérieur de l'appareil
est trop élevée, le voyant d'alarme clignote.
Activez la fonction Super.
Mise à l'arrêt
Pour éteindre l'appareil, tournez le
thermostat sur la position « O ».
Le voyant s'éteint.
Réglage de la température
La température est régulée
automatiquement.
Pour utiliser l'appareil, procédez comme
suit :
tournez le thermostat sur la position
minimale pour obtenir moins de
froid.
tournez le thermostat sur la position
maximale pour obtenir plus de froid.
Un réglage intermédiaire est
généralement le plus indiqué.
Toutefois, on obtiendra le
réglage exact en tenant compte
du fait que la température à
l'intérieur de l'appareil dépend
de plusieurs facteurs :
la température ambiante
la fréquence d'ouverture
de la porte
la quantité d'aliments
stockés
l'emplacement de
l'appareil.
19
Fonction Super
Pour activer la fonction Super, appuyez sur
la touche Super.
Le voyant Super s'allume.
Cette fonction s'arrête
automatiquement au bout de
52 heures.
Il est possible de désactiver
cette fonction à tout moment en
appuyant sur la touche Super.
Le voyant Super s'éteint.
Alarme haute température
Une augmentation de la température dans
un compartiment (par exemple à cause
d'une panne de courant) est indiquée par le
clignotement du voyant Alarme.
Une fois rétablies les conditions normales
de fonctionnement, le voyant Alarme
s'éteint automatiquement.
PREMIÈRE UTILISATION
Nettoyage de l'intérieur
Avant d'utiliser l'appareil pour la première
fois, nettoyez l'intérieur et tous les
accessoires avec de l'eau tiède savonneuse
(pour supprimer toute odeur de neuf), puis
séchez-les soigneusement.
ATTENTION! N'utilisez jamais
de produits abrasifs ou
caustiques car ils pourraient
endommager le revêtement.
UTILISATION QUOTIDIENNE
Congélation d'aliments frais
Le compartiment congélateur est idéal pour
congeler des aliments frais et conserver
longtemps des aliments congelés ou
surgelés.
Pour congeler de petites quantités
d'aliments frais, il n'est pas nécessaire de
modifier le réglage actuel.
Activez la fonction Super au moins
24 heures avant d'introduire des aliments
frais à congeler dans le compartiment
congélateur.
Placez les denrées à congeler dans les
deux compartiments supérieurs.
La quantité maximale de denrées que vous
pouvez congeler par tranche de 24 heures
figure sur la plaque signalétique, située à
l'intérieur de l'appareil.
Le processus de congélation dure
24 heures : vous ne devez ajouter aucun
autre aliment à congeler pendant cette
période.
Une fois le processus de congélation
terminé, revenez à la température souhaitée
(voir « Fonction Super »).
Conservation d'aliments
congelés et surgelés
À la mise en service ou après un arrêt
prolongé, placez le thermostat sur la
position maximale pendant 2 heures
environ avant d'introduire les produits dans
le compartiment.
En cas de décongélation
accidentelle, due par exemple à
une coupure de courant, si la
coupure a duré plus de temps
qu'indiqué au paragraphe
« Autonomie de
fonctionnement » du chapitre
Caractéristiques techniques,
consommez rapidement les
aliments décongelés ou cuisez-
les immédiatement avant de les
recongeler (une fois refroidis).
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48

Smeg S3F092P Manuel utilisateur

Catégorie
Congélateurs
Taper
Manuel utilisateur

dans d''autres langues