Heartland HCTTDW Le manuel du propriétaire

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,

please visit our website at www.agamarvel.com for additional information. If you still need assistance, call us at 1-800-223-3900.

You will need your model and serial number, located near the door on the right or left side, inside the dishwasher.

AGA Marvel

1260 E. VanDeinse St.

Greenville MI 48838

Toll free phone: 800-223-3900

Fax: 616-754-9690

www.agamarvel.com

Classic Model HCTTDW Dishwasher Instructions

11/30/12

INSTALLATION INSTRUCTIONS

DISHWASHER SAFETY.............................................................. 2

INSTALLATION REQUIREMENTS ........................................... 3

Tools and Parts........................................................................... 3

Location Requirements........................................................... 4

Drain Requirements ................................................................ 6

Water Supply Requirements................................................. 6

Electrical Requirements ........................................................ 6

INSTALLATION INSTRUCTIONS ............................................ 7

Prepare Cabinet Opening—Existing Utilities................. 7

Prepare Cabinet Opening—New Utilities ....................... 7

Prepare and Route Water Line ............................................ 8

Install Drain Hose..................................................................... 9

Prepare Dishwasher................................................................11

USER INSTRUCTIONS

What’s new in your Dishwasher ....................................... 26

Parts and Features ................................................................ 27

Quick Steps .............................................................................. 28

Dishwasher Use ..................................................................... 29

Cycle and Option Descriptions ......................................... 31

Dishwasher Features ............................................................ 34

Filtration System .................................................................... 36

Dishwasher Care .................................................................... 37

Troubleshooting .................................................................... 38

Make Power Supply Cord Connection ........................... 13

Determine Cabinet Opening.............................................. 14

Choose Attachment Option............................................... 15

Move Dishwasher Close to Cabinet Opening.............. 16

Connect to Water Supply ................................................... 18

Connect to Drain.................................................................... 19

Make Direct Wire Electrical Connection........................ 20

Secure Dishwasher in Cabinet Opening ........................ 21

Complete Installation........................................................... 23

Check Operation.................................................................... 24

If Dishwasher Does Not Operate...................................... 24

Additional Tips ....................................................................... 24

Table of Contents

Warranty ................................................................................... 40

41012974 revA

2

You Need to:

Slowly open dishwasher door while someone grasps the rear

of the dishwasher. Remove shipping materials, drain hose and

lower rack. Close dishwasher door until latched.

Observe all governing codes and ordinances.

Install this dishwasher as sp n these instructions.

Installation should be performed by a qu service

technician. The dishwasher must be installed to meet all

electrical and plumbing national and local codes and

ordinances.

WARNING

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

Care shall be exercised, when the appliance is installed or

removed, to reduce the liklihood of damage to the

powersupply cord.

Dishwasher Safety

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

3

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the recommended tools and parts before starting

installation. Read and follow the instructions provided with any

tools listed here.

All Installations

Tools needed:

*Must be the proper size to connect your household wiring

to 16-gauge wiring in dishwasher.

Other useful items you may need:

Parts supplied:

Make sure all these parts are included in the literature package.

Parts needed:

Other parts you may also ne

ed:

NOTE: Parts available for purchase in plumbing supply stores.

Check local codes. Check existing electrical supply. See

“Electrical Requirements” section. It is recommended that

electrical connections be made by a licensed electrical installer.

In addition, for rst-time installations

Tools needed:

Parts needed:

†®TORX and T20 are registered trademarks of Saturn Fasteners, Inc.

4

Location Requirements

Grounded electrical supply required.

Do not run drain lines, water lines or electrical wiring where they

can interfere with or contact dishwasher motor or legs.

The location where the dishwasher will be installed must provide

clearance between motor and

ooring. Motor should not touch

the

oor.

Do not install dishwasher over carpeted

g.

Shelter dishwasher and water lines leading to dishwasher against

freezing. Damage from freezing is not covered by the warranty.

A side panel kit is avai

lable from your dealer for installing your

dishwasher at the end of your cabinetry.

A moisture barrier accessory is available

from

your dealer for installing underneath the countertop.

Check location where dishwasher will be installed. The location

must provide:

easy access to water, electricity and drain.

convenient access for loading and unloading dishes.

Corner locations require a 2" (5.1 cm) minimum clearance

between the side of the dishwa sher door and the wall or

cabinet.

square opening for proper operation and appearance.

cabinet front perpendicular to r.

level r. (If oor at front of opening is not level with or

at rear of opening, shims may be needed to level

dishwasher.)

Helpful Tip: Be sure to accurately measure dimensions and

ensure dishwasher is level if the

oor in the dishwasher opening is

uneven (example: Flooring extends only partway into opening).

NOTE: To avoid shifting during dishwasher operation, shims must

be securely attached to the

oor.

If dishwasher will be left unused for a period of time or in a

location where it may be subject to freezing, have it winterized by

authorized service personnel.

Make sure pipes, wires and drain hose are within the shaded area

shown in the “Product and

Cabinet Opening Dimensions” section.

5

23-7/8”

(60.7cm)

33-7/8”

(86.1cm)

24-5/8”

(62.5cm)

27-1/16”

(68.7cm)

6

Drain Requirements

A new drain hose is supplied with your dishwasher. If drain

hose is not long enough, use a new drain hose with a

maximum length of 12 ft (3.7 m) that

meets all current AHAM/IAPMO test standards, is resistant to

heat and detergent, and

the 1" (2.5 cm) drain connector of

the dishwasher.

Make sure to connect drain hose to waste tee or disposer inlet

above drain trap in house plumbing and 20" (50.8 cm)

minimum above the

or. It is recommended that the drain

hose either be looped up and securely fastened to the

underside of the counter, or be connected to an air gap.

Make sure to use an air gap if the drain hose is connected to

house plumbing lower than 20" (50.8 cm) above sub

oor or

oor.

Use " minimum I.D. drain line ttings.

If required, the air gap should be installed in accordance with

the air gap installation instruct

ions. When you are connecting

the air gap, a rubber hose (not provided) will be needed to

connect to the waste tee or disposer inlet.

Water Supply Requirements

A hot water line with 20 to 120 psi (138 to 862 kPa) water

pressure can be

d

by a licensed plumber.

120°F (49°C) water at dishwasher.

³⁄ " O.D. copper tubing with compression tting or le

braided water supply line

NOTE: ¹⁄

" minimum plastic tubing is not recommended.

A 90° elbow with ³ " hose connection with rubber washer.

Do not solder within 6" (15.2 cm) of the water inlet valve.

Electrical Requirements

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electrical Code, ANSI/NFPA

70 - latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

You must have:

120-volt, 60 Hz, AC-only, 15- or 20-amp, fused electrical

supply.

Copper wire only.

We recommend:

A time-delay fuse or circuit breaker.

A separate circuit.

If connecting dishwasher with a

power supply cord:

Use UL Listed power supply cord kit

marked for use with dishwasher.

Power supply cord must plug into a grounded

3 prong outlet, located in the cabinet next to

the dishwasher opening. Outlet must meet all

local codes and ordinances.

If connecting dishwasher with direct wiring:

Use exible, armored or nonmetallic

sheathed, copper wire with

grounding wire that meets the

wiring requirements for your home

and local codes and ordinances.

Use a UL Listed/CSA Approved strain relief.

(part number S41013050)

7

INSTALLATION INSTRUCTIONS

Prepare Cabinet Opening—Existing

Utilities

If the water line and the cable extend to the locations shown,

proceed to the “Install Drain Hose” section. If they do not reach far

enough, follow the instructions in the “Prepare Cabinet Opening—

New Utilities” section.

Prepare Cabinet Opening—New

Utilities

Prepare and route the electrical supply

Option A, Power Supply Cord:

NOTE: A grounded 3 prong outlet is required inside a cabinet next

to the dishwasher cabinet opening.

Drill a 1¹

" (3.8 cm) hole in cabinet side or rear.

See “Product and Cabinet Opening Dimensions” section.

WARNING

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

Electrical Shock Hazard

8

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover hole with grommet included with power

supply cord kit.

Option B, Direct Wire:

Helpful Tip: Wiring the dishwasher will be easier if you route the

cable into the cabinet opening from the right-hand side.

Drill a 1¹ " (3.8 cm) hole in right-hand cabinet side or rear.

See “Product and Cabinet Opening Dimensions” section.

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover hole with grommet

not provided .

Route cable from power supply through cabinet hole (cable must

extend to the right front side of cabinet opening). Tape cable to

the

in area shown. This will

prohibit cable from moving when

dishwasher is moved into cabinet opening.

Prepare and Route Water Line

Helpful Tip: Routing the water line through the left side of cabinet

opening will make water connection easier.

Drill a ¹⁄ " (1.3 cm) hole in the cabinet side or rear.

Measure overall length of copper tubing for the water supply line.

9

Attach the water supply line (copper tubing or exible braided line)

to the hot water line using a connection con

guration that is in

compliance with local codes and ordinances. The water supply to

the dishwasher should have a manual shuto valve located under

the sink.

Slowly route water supply line through hole in cabinet. (If you are

using copper tubing, it will bend and kink easily, so be gentle.) It

should be far enough into the cabinet opening to connect it to the

dishwasher inlet on the front left side of the dishwasher.

Slowly turn water shuto valve to “ON” position. Flush water into

a shallow pan until clear to get rid of particles that could clog the

inlet valve. Turn shuto valve to “OFF” position.

Route water line and tape it to the

oor in area shown. This will

keep it from moving when dishwasher is moved into cabinet

opening.

Install Drain Hose

IMPORTANT: Always use a new drain hose. Check local codes to

determine whether an air gap is required.

If needed, drill a 1¹⁄

" (3.8 cm) diameter hole in cabinet wall or side

of the opening closest to the sink.

Route drain hose as shown through hole in cabinet to the front

center of opening where drain connection will be made. Tape

drain hose to the

n area show

n. This will prohibit it from

moving when dishwasher is moved into cabinet opening.

10

IMPORTANT: The drain hose connection of the disposer or a

waste tee must be made before the drain trap and at least

20" (50.8 cm) above the

here the dishwasher will be

installed.

Helpful Tip: To reduce vibration of the hose, keep the hose away

from the

oor.

Option A, Waste disposer – no air gap

Option B, No waste disposer – no air gap

Option C, Waste disposer – with air gap

1. Using a hammer and screwdriver,

knock plug into disposer.

2. Use needle-nose pliers to remove

plug.

3. Attach drain hose to disposer inlet

with large blue drain hose clamp

(provided). Use pliers to squeeze

clamp open and move into position.

1. Fit rubber end of drain hose to waste

tee and cut if needed.

NOTE: Do not cut ribbed section.

2. Attach rubber end of drain hose to

waste tee with a large blue drain

hose clamp (provided). Use pliers to

squeeze clamp open and move into

position. If the drain hose was cut,

use a 1 ¹

" to 2" (3.8 to 5 cm) screw-

type clamp (not provided).

1. Using a hammer and screwdriver,

knock plug into disposer.

2. Use needle-nose pliers to remove

plug.

3. Connect rubber end of drain hose to

air gap and cut if needed.

NOTE: Do not cut ribbed section.

4. Attach drain hose to air gap with

large blue drain hose clamp

(provided). Use pliers to squeeze

clamp open and move into position.

If the drain hose was cut, use a 1¹⁄

"

to 2" (3.8 to 5 cm) screw-type clamp

(not provided).

5. Use a rubber hose

(not provided)

with screw-type clamps (not

provided) to connect from air gap to

disposer inlet.

11

Option D, No waste disposer – with air gap

Prepare Dishwasher

Remove and discard the foam blocks located above the front legs

on each side of the dishwasher. The blocks cover the rope/link

pulleys on the dishwasher.

Helpful Tip: Place cardboard under dishwasher until installed in

cabinet opening to avoid damaging

oor covering. Do not use

door panel as a worktable without

covering with a towel to

avoid scratching the door panel.

1. Connect rubber end of drain hose to

air gap and cut if needed.

NOTE: Do not cut ribbed section.

2. Attach drain hose to air gap with

large blue drain hose clamp

(provided). Use pliers to squeeze

clamp open and move into position.

If the drain hose was cut, use a 1-1/2”

to 2" (3.8 to 5 cm) screw-type clamp

(not provided).

3. Use a ru

bber hose (not provided)

with scr

ew-type clamps (not

provided) to connect from waste tee

to air gap.

WARNING

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

12

Using two or more people, grasp sides of dishwasher door frame

and place dishwasher on its back.

Remove and discard the plastic rail cover on each side of the

dishwasher frame. To remove the plastic rail cover, push upward

and back to unsnap it from the dishwasher frame.

Using a

screwdriver, turn the plastic fasteners ¼ turn

counterclockwise to unlock them . Remove panel. Do not remove

tech sheet from access panel.

Using a ¹

" hex head socket, nut driver or Torx

®

T20

®

screwdriver,

remove terminal box cover. Retain for later use.

Install a UL Listed/CSA Approved strain relief. Make sure screw

heads are facing to the left when tightening conduit nut. Strain

relief is provided with the power supply cord kit.

NOTE: If using Option B, proceed to “Determine Cabinet

Opening,” to continue with the installation of your dishwasher.

13

Make Power Supply Cord Connection

Option A, Power Supply Cord:

Route cord so that it does not

touch dishwasher motor to lower

part of dishwasher tub. Pull cord through strain relief in terminal

box.

Select UL Listed/CSA Approved twist-on wire connectors rated to

connect your power supply cord to 16-gauge dishwasher wiring.

Remove the green grounding screw and place through the ring

terminal of the green ground wire. Reattach and tighten the green

screw.

NOTE

: Do not pre-twist stranded wire. Twist on wire connector.

Gently tug on wires to be sure both are secured.

WARNING

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in

terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

14

Connect wires black to black and white to white, using UL

Listed/CSA Approved twist-on wire connectors.

Tighten strain relief screws to secure cord.

Place wires inside termina

l box. Insert tabs on left side of cover.

Make sure wires are tucked inside box. Close cover ensuring

wires are not pinched. Use

¹⁄

" nut driver or Torx

®

T20

®

screwdriver

and previously removed screw to secure cover.

NOTE: Do not plug into outlet until instructed to do so.

Determine Cabinet Opening

Measure height of cabinet opening from underside of countertop

to

where dishwasher will be installed (you will need to

measure the lowest point on the underside of the countertop and

the highest point on the

oor). Refer to “Dishwasher Height

Adjustment Chart” for wheel position and the number of turns

needed.

NOTE: If the minimum cabinet opening height is less than

34" (86.4 cm), the rear wheels can be removed for additional

clearance. This will allow the dishwasher to

t into a 33¹

"

(85.1 cm) high cabinet opening, but the dishwasher will be more

di

cult to move. (Measurements are approximate. Wheels and

legs are preset at the factory for 34¹⁄

" [87.6 cm].)

Turn bo

th leveler legs to the same height. Put wheels in the

required position determined from “Dishwasher Height

Adjustment Chart.”

15

Built-up oors: If the kitchen oor is higher than the cabinet

opening's

oor - for example, the kitchen oor tile does not

extend into the cabinet opening - add shims as needed in the area

shown to bring the dishwasher up to 34" (86.4 cm) below the

countertop.

NOTE: Shims must be securely attached to

oor to avoid

movement when the dishwasher is in use.

Choose Attachment Option

Using 2 or more people, stand the dishwasher up.

IMPORTANT: The dishwasher must be secured to the cabinet.

There are two brackets found in the parts bag. Attach the

brackets using Option Number 1 if the countertop is wood,

laminate or another similar surface. If your countertop is marble,

granite or another hard surface, install using Option Number 2.

Option 1, Countertop Attachment

Remove the brackets from the package and insert into the open

slots on the left and right-hand top of the dishwasher collar as

shown.

Using a pair of pliers, bend the tab down to secure the bracket in

place. Repeat this step for the other side.

NOTE: Do not attach the dishwasher. This will be done later.

Option 2, Side Attachment

For marble, granite, or other hard surface countertops

NOTE: Remove the brackets from the parts package.

Break o

the end of the bracket along the scored line.

With another person holding the rear of the dishwasher to keep it

from tipping, open dishwasher door and place towel over pump

assembly and spray arm of dishwasher. This will keep screws

from falling into pump area when you are securing dishwasher to

cabinet.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

16

Push the plastic buttons out of the side of the tub.

NOTE: Save the buttons to cover the holes after dishwasher is

installed.

Push bracket into slot on the side of dishwasher, and bend tab in

toward the side of the dishwasher so that it keeps the bracket in

place. Repeat this step for the other side of the dishwasher.

NOTE: Do not attach the dishwasher. This will be done later.

Move Dishwasher Close to Cabinet

Opening

NOTE: Do not install kick plate until instructed to do so.

IMPORTANT: Double-check correct placement of utilities. Grasp

the sides of the dishwasher at the edges of the door panel. Tilt

dishwasher backward on wheels and move dishwasher close to

cabinet opening.

NOTE: Do not push on the front of the panel or on the console.

Panel or console may dent.

Helpful Tip: Temporarily tape utilities to the oor in the locations

shown to prohibit them from moving when dishwasher is moved

into the cabinet opening.

Check that water line is on the left side of opening and drain hose

is near the center of the cabinet opening.

With another pers

on holding the dishwasher to keep it from

tipping, open and close the door a few times. If the door closes or

falls open under its own weight, the door tension will need to be

adjusted.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

17

To adjust the door spring tension, unhook the spring from the rear

leg of dishwasher.

Using a 5⁄16 " nut driver or hex socket, remove the screw from the

tensioner.

The screw can be put into one of three holes (1, 2, 3) in the front

leg of dishwasher. If the door closes by itself, move the tensioner

to a higher number hole and replace the screw. Reattach door

spring to rear leg.

NOTE: Tensioners on both sides of dishwasher should be secured

at same holes.

When door is unlatched and door opens by itself, move the

tensioner to a lower numbered hole and replace the screw.

Reattach door spring to rear leg.

NOTE: Tensioners on both sides of dishwasher should be secured

at s

ame holes.

IMPORTANT: If wheels were removed, cover the oor when

moving the dishwasher to avoid damage to the oor. Slowly move

dishwasher completely into cabinet opening. Do not kink or pinch

water line, drain hose, power supply cord or direct wire between

dishwasher and cabinet. Remove cardboard from under

dishwasher.

NOTES:

It is all right if dishwasher ts tightly into cabinet opening. Do

not remove insulation blanket – the blanket reduces the sound

level.

If using power cord, make sure to route end through hole in

cutout before sliding dishwasher into cabinet opening.

Align front of dishwasher door panel with front of cabinet doors.

You may need to adjust alignment to be even with your cabinets.

18

Check that leveling legs are rmly against the oor. Close and

latch the door, and place level against the front panel. Check that

dishwasher is centered from front to back in the opening. If

needed, adjust leveling leg until dishwasher is plumb. Repeat for

other side of dishwasher.

Helpful Tip: Push up on front of dishwasher to raise dishwasher

o the ground to adjust front legs. With some installations, it may

be easier to adjust the front leg using the ³⁄16" hex head socket or

adjustable wrench.

To raise the rear of the dishwasher, adjust the rear leveling leg

using a Phillips screwdriver. Turn clockwise until the dishwasher is

level front to r

ear.

Place level against top front opening of tub. Check that

dishwasher is level from side-to-side. If dishwasher is not level,

adjust front legs up or down until dishwasher is level. Close the

dishwasher door.

Connect to Water Supply

Copper tubing only: Slide nut, then ferrule, about 1" (2.5 cm) onto

copper tubing.

NOTE: To avoid vibration during operation, route the water supply

line so that it does not touch the dishwasher base, frame or motor.

19

Connect the ³⁄8" compression tting to the water supply line prior

to installing the unit into the cabinet opening. Attach so that the

³⁄4" connection is facing upward as shown above.

Copper tubing only: Put the tubing into the 90° elbow tting as far

as it will go (the copper tubing bends and kinks easily). Slide the

nut and ferrule forward and start the nut onto the elbow threads.

Flexible braided connection: Secure nut to elbow using 5⁄8" open

ended wrench or adjustable wrench.

NOTE : Do not use Teon

®†

tape with compression ttings.

Be sure rubber washer is properly seated in tting. Slide the

³⁄4" tting up to the valve and hand tighten to

avoid cross-

threading. Hand tighten until the coupling is tight.

Using pliers, check the tightness of the coupling. An additional

¹⁄4 to ¹⁄2 turn may be required to seal the rubber gasket.

NOTE: Do not overtighten. Damage to the coupling can result.

Place paper towel under 90° elbow tting. Turn on water supply

and check for leaks. If leak occurs, repeat previous step.

Connect to Drain

Place towel under drain hose to catch any water in drain hose.

Place the small green drain hose clamp onto the small end of the

drain hose. Push the new drain hose into the black drain hose

connector up to the drain hose stop.

Using pliers, squeeze open the small green drain hose clamp and

slide onto connector between stops.

After hose is connected, remove towel.

†®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

20

Make Direct Wire Electrical Connection

NOTE: If the power supply cord was connected earlier, proceed to

“Secure Dishwasher in Cabinet Opening” section.

Option B, Direct Wire:

Route cable so that it does not touch dishwasher motor or lower

part of dishwasher tub. Pull cable through UL Listed/CSA

Approved strain relief in terminal box. Strain relief is not supplied

with the dishwasher. Owner must purchase a

" screw-in type

strain relief.

Select UL Listed/CSA Approved twist-on wire connectors (not

included) rated to connect your household wiring to 16-gauge

dishwasher wiring.

Form bare ground wire into a U-shaped hook. Wrap ground wire

hook clockwise around ground connector screw and under the

washer. Securely tighten ground connector.

NOTE: Do not pre-twist stranded wire. Twist on UL listed/CSA

approved wire connector. Gentl

y tug on wires to be sure both are

secured.

WARNING

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in

terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

La page charge ...

Heartland HCTTDW Le manuel du propriétaire

Ce manuel convient également à

Heartland HCTTDW Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents