Indesit SDLE 129 (EU) Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire

Ce manuel convient également à

GB
1
English,1
Contents
Installation, 2-3-4-5
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Instructions for the fitter
Description of the washer dryer, 6-7
Control panel
Display
How to run a wash cycle or a drying cycle, 8
Wash cycles and functions, 9
Table of wash cycles
Wash functions
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Special wash cycles
Load balancing system
Precautions and tips, 11
General safety
Disposal
Opening the porthole door manually
Care and maintenance, 12
Cutting off the water or electricity supply
Cleaning the washer dryer
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 13
Service, 14
GB
SDLE 129
Instructions for use
WASHER DRYER
ES
Español,29Français,15
F
2
GB
A
Installation
This instruction manual should be kept in a safe
place for future reference. If the washer dryer is sold,
transferred or moved, make sure that the instruction
manual remains with the machine so that the new
owner is able to familiarise himself/herself with its
operation and features.
Read these instructions carefully: they contain vital
information relating to the safe installation and
operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washer dryer from its packaging.
2. Make sure that the washer dryer has not been
damaged during the transportation process. If it has
been damaged, contact the retailer and do not
proceed any further with the installation process.
3. Remove the 4
protective screws (used
during transportation) and
the rubber washer with
the corresponding
spacer, located on the
rear part of the appliance
(see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need
them again if the washer dryer needs to be moved to
another location.
Packaging materials should not be used as toys for
children.
Levelling
1. Install the washer dryer on a flat sturdy floor,
without resting it up against walls, furniture cabinets
or anything else.
2. If the floor is not
perfectly level, compen-
sate for any unevenness
by tightening or loosening
the adjustable front feet
(see figure); the angle of
inclination, measured in
relation to the worktop,
must not exceed 2°.
Levelling the machine correctly will provide it with
stability, help to avoid vibrations and excessive noise
and prevent it from shifting while it is operating. If it is
placed on carpet or a rug, adjust the feet in such a
way as to allow a sufficient ventilation space
underneath the washer dryer.
Connecting the electricity and water
supplies
Connecting the water inlet hose
1. Insert seal A into the
end of the inlet hose and
screw the latter onto a
cold water tap with a 3/4
gas threaded opening
(see figure).
Before performing the
connection, allow the
water to run freely until it
is perfectly clear.
2. Connect the inlet hose
to the washer dryer by
screwing it onto the
corresponding water inlet
of the appliance, which is
situated on the top right-
hand side of the rear part
of the appliance (see
figure).
3. Make sure that the hose is not folded over or bent.
The water pressure at the tap must fall within the
values indicated in the Technical details table (see
next page).
If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
Never use second-hand hoses.
Use the ones supplied with the machine.
GB
3
Te ch n i c a l d a t a
Model
SDLE 129
Dimensions
width 59.5 cm
height 81,5 cm
depth 54,5 cm
Capacity
from 1 to 7 kg for the wash programme;
from 1 to 5 kg for the drying programme
Electrical
connections
please refer to the technical data plate
fixed to the machine
Water
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed
up to 1200 rotations per minute
Energy rated
programmes
according to
regulation
EN 50229
Wash:
programme
(1
st
press of the
button); temperature 60°C;
using a load of 7 kg.
Drying: first drying cycle performed with a
2 kg load, by selecting the "IRON DRY"
dryness level;
The second drying cycle is performed
with a 5 kg load, by selecting the
"CUPBORD DRY" dryness level.
This appliance conforms to the following
EC Directives:
- 89/336/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent modifications
- 2002/96/EC
- 2006/95/EC (Low Voltage)
65 - 100 cm
Connecting the drain hose
Connect the drain hose,
without bending it, to a
drainage duct or a wall
drain located at a height
between 65 and 100 cm
from the floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening the
duct supplied to the tap
(see figure). The free end
of the hose should not
be underwater.
We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity
socket, make sure that:
the socket is earthed and complies with all
applicable laws;
the socket is able to withstand the maximum power
load of the appliance as indicated in the Technical
data table (see opposite);
the power supply voltage falls within the values
indicated in the Technical data table (see opposite);
the socket is compatible with the plug of the
washer dryer. If this is not the case, replace the
socket or the plug.
The washer dryer must not be installed outdoors,
even in covered areas. It is extremely dangerous to
leave the appliance exposed to rain, storms and other
weather conditions.
When the washer dryer has been installed, the
electricity socket must be within easy reach.
Do not use extension cords or multiple sockets.
The cable should not be bent or compressed.
The power supply cable must only be replaced by
authorised technicians.
Warning! The company shall not be held responsible
in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, using the wash cycle
.
4
GB
Instructions for the fitter
Mounting the wooden panel onto the door and
inserting the machine into cabinets:
In the case where the machine must be shipped for final
installation after the wooden panel has been mounted, we
suggest leaving it in its original packaging. The packaging
was designed to make it possible to mount the wooden
panel onto the machine without removing it completely
(see figures below).
The wooden panel that covers the face of the machine
must not be less than 18 mm in thickness and can be
hinged on either the right or left. For the sake of
practicality when using the machine, we recommend that
the panel be hinged on the same side as the door for the
machine itself - the left.
A
B
C
D
E
Tur seite
Door Mounting Accessories (Fig. 1-2-3-4-5).
Fig. 1
N° 2 Hinges
N° 1 Magnet N° 1 Magnet plate
N° 1 Rubber plug
N° 2 Hinge Supports
N° 4 Spacers
Fig. 2
Fig. 3 Fig. 4
Fig. 5
Fig. 4/B
- No. 6 type A self-threading screws, l =13 mm.
- No. 2 type B metric, countersunk screws, l =25; for
fastening the magnet plate to the cabinet.
- No. 4 type C metric screws, l =15 mm; for mounting the
hinge supports to the cabinet.
- No. 4 type D metric screws, l =7 mm; for mounting the
hinges on the supports.
Mounting the Parts onto the Face of the Machine.
- Fit the hinge supports to the appliance front panel,
positioning the hole marked with an arrow in fig. 1 so that it
is on the inner side of the front panel. Fit a spacer (fig. 4/B)
between the surfaces using type C screws.
- Fit the magnet plate at the top of the opposite side,
using type B screws to fix two spacers (fig. 4/B) between
the plate and the surface.
GB
5
Using the Drilling Template.
- To trace the positions of the holes on the left-hand side
of the panel, align the drilling template to the top left side
of the panel using the lines traced on the extremities as a
reference.
- To trace the positions of the holes on the right-hand
side of the panel, align the drilling template to the top
right side of the panel.
- Use an appropriately sized router to mill the holes for
the two hinges, the rubber plug and the magnet.
Mounding the Parts onto the Wooden Panel (Door).
- Insert the hinges into the holes (the movable part of the
hinge must be positioned facing away from the panel) and
fasten them with the 4 type A screws.
- Insert the magnet into the top hole on the opposite side
of the hinges and fasten it with the two type B screws.
- Insert the rubber plug into the bottom hole.
The panel is now ready to be mounted onto the machine.
Mounting the Panel into the machine.
Insert the nib of the hinge (indicated by the arrow in fig. 2)
into the hole for the hinge and push the panel towards the
front of the machine. Fasten the two hinges with the type
D screws.
Fastening the plinth guide.
If the machine is installed at the end of a set of modular
cabinets, mount either one or both of the guides for the
base molding (as shown in fig. 8). Adjust them for depth
based on the position of the base molding, and, if
necessary, fasten the base to the guides (fig. 9).
This is how to assemble the plinth guide (fig. 8):
Fasten angle P using screw R, insert plinth guide Q into
the special slot and once it is in the desired position, lock
it in place using angle P and screw R.
Inserting the machine into the Cabinet.
- Push the machine into the opening, aligning it with the
cabinets (fig. 6).
- Regulate the adjustable feet to raise the machine to the
appropriate height.
- To adjust the position of the wooden panel in both the
vertical and horizontal directions, use the C and D
screws, as shown in fig. 7.
Important: close the lower part of the appliance front by
ensuring that the plinth rests against the floor.
Fig. 8 Fig. 9
Accessories provided for the height adjustment.
The following can be found inside the polystyrene lid (fig. 10):
2 crossbars (G), 1 strip (M)
the following can be found inside
the appliance drum:
4 additional feet (H),
4 screws (I),
4 screws (R),
4 nuts (L),
2 plinth guides (Q)
Adjusting the appliance height.
The height of the appliance can be adjusted (from 815 mm
to 835 mm), by turning the 4 feet.
Should you require the appliance to be placed higher than
the above height, you need to use the following accessories
to raise it to up to 870 mm:
the two crossbars (G); the 4 feet (H); the 4 screws (I); the 4
nuts (L) then perform the following operations (fig. 11):
remove the 4 original feet, place a crossbar G at the front of
the appliance, fastening it in place using screws I (screwing
them in where the original feet were) then insert the new feet H.
Repeat the same operation at the back of the appliance.
Now adjust feet H to raise or lower the appliance from 835
mm to 870 mm.
Once you have reached the desired height, lock nuts L onto
crossbar G.
To adjust the appliance to a height between 870 mm and
900 mm, you need to mount strip M, adjusting feet H to the
required height.
Insert the strip as follows:
loosen the three screws N situated at the front of the Top
cover of the appliance, insert strip M as shown in fig. 12,
then fasten screws N.
D
C
C
570
min
815
540
595
820 ÷ 900
600 min
Fig. 6 Fig. 7
L
I
H
G
M
Fig. 11 Fig. 12
Fig. 10
6
GB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see Detergents
and laundry).
ON/OFF button
: press this briefly to switch the
machine on or off. The START/PAUSE indicator light,
which flashes slowly in a green colour shows that the
machine is switched on. To switch off the washer
dryer during the wash cycle, press and hold the
button for approximately 2 seconds; if the button is
pressed briefly or accidentally the machine will not
switch off. If the machine is switched off during a
wash cycle, this wash cycle will be cancelled.
WASH CYCLE SELECTOR buttons: used to set the
desired wash cycle (see "Table of wash cycles").
MEMORY button: press and hold the button to store
a cycle with your own set of preferences in the
memory of the machine. To recall a previously stored
cycle, press the MEMO button.
FUNCTION buttons: press the button to select the
desired function. The corresponding indicator light on
the display will switch on.
SPIN button
: press to reduce or completely
exclude the spin cycle - the value is indicated on the
display.
TEMPERATURE button
: press to decrease the
temperature: the value will be shown on the display.
CONTROL PANEL LOCK button
: to activate the
control panel lock, press and hold the button for
approximately 2 seconds. When the symbol
is
illuminated, the control panel is locked. This means it
is possible to prevent wash cycles from being modified
accidentally, especially where there are children in the
home. To deactivate the control panel lock, press
and hold the button for approximately 2 seconds.
DELAYED START button
: press to set a delayed
start time for the selected wash cycle. The delay time
will be shown on the display.
DRYING button
: press to set a drying cycle.
START/PAUSE button with indicator light: when the
green indicator light flashes slowly, press the button to
start a wash cycle. Once the cycle has begun the
indicator light will remain lit in a fixed manner. To
pause the wash cycle, press the button again; the
indicator light will flash in an orange colour. If the
symbol
is not illuminated, the door may be
opened. To start the wash cycle from the point at
which it was interrupted, press the button again.
Description of the washer dryer
Control panel
TEMPERATURE
Button
WASH
CYCLE
SELECTOR
Buttons
Detergent dispenser drawer
FUNCTION
buttons
ON/OFF
button
SPIN SPEED
Button
START/PAUSE
button with
indicator light
DRYING
Button
DISPLAY
DELAYED
START
Button
MEMORY
Button
CONTROL PANEL
LOCK
button
GB
7
Display
The display is useful when programming the machine and provides a great deal of information.
The upper two strings A and B are used to display the selected wash cycle or the type of drying selected, the
current wash cycle phase (the selected dryness level or drying time) and all the indications relating to the progress
status of the cycle.
String C shows the time remaining until the end of the wash cycle in progress and, if a DELAYED START has been
set, the time remaining until the start of the selected wash cycle.
String D shows the maximum spin speed value (this depends on the selected wash cycle); if the wash cycle does
not include a spin cycle, the string remains unused.
String E shows the maximum temperature value which may be selected (this depends on the wash cycle used); if
the temperature of the wash cycle cannot be modified, the string remains unused.
Indicator lights F correspond to the functions and light up when the selected function is compatible with the set
wash cycle.
Door locked symbol
If the symbol is lit, this indicates that the washer dryer door is blocked to prevent it from being opened
accidentally. To prevent any damage from occurring, wait for the symbol to switch itself off before opening the
appliance door.
N.B.: if the DELAYED START function has been activated, the door cannot be opened; pauses the machine by
pressing the START/PAUSE button if you wish to open it.
The first time the machine is switched on, you will be asked to select the language and the display will
automatically show the language selection menu.
To select the desired language press the TEMPERATURE and SPIN buttons; to confirm the selection press the
DRYING button.
If you wish to select another language, press and hold the DRYING + TEMPERATURE + SPIN buttons
simultaneously for 5 seconds, then repeat the steps listed above.
A
B
C
D
E
F
8
GB
How to run a wash cycle or a
drying cycle
1. SWITCH THE MACHINE ON.Press the button; the
text WELCOME will appear on the display and the START/
PAUSE indicator light will flash slowly in a green colour.
2. LOAD THE LAUNDRY. Open the porthole door. Load
the laundry, making sure you do not exceed the
maximum load value indicated in the table of
programmes on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent into
the relevant compartments as described in "Detergents
and laundry".
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Press one of the WASH
CYCLE SELECTOR buttons to select the required wash
cycle; the name of the wash cycle will appear on the
display. A temperature and spin speed is set for each
wash cycle; these may be adjusted. The duration of the
cycle will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modifying the temperature and/or spin
speed.The machine automatically selects the maximum
temperature and spin speed set for the selected wash
cycle; these values cannot therefore be increased. The
temperature can be decreased by pressing the
button, until the cold wash "OFF" setting is reached. The
spin speed may be progressively reduced by pressing
the
button, until it is completely excluded (the "OFF"
setting). If these buttons are pressed again, the
maximum values are restored.
Setting a delayed start.
To set a delayed start for the selected programme,
press the corresponding button repeatedly until the
required delay period has been reached. When this
option is enabled, the
symbol lights up on the
display. To remove the delayed start function press the
button until the text "OFF" appears on the display.
Setting the drying cycle.
The desired drying cycle type may be set by pressing
the DRYING button once or several times. Two options
are available:
A - Based on the how damp the clothes are once they
have been dried:
Iron dry: slightly damp clothes, easy to iron.
Hanger dry: dry clothes to put away.
Cupboard dry: very dry clothes, recommended for
towelling and bathrobes.
B - Based on time: from 40 minutes to 180.
To exclude the drying phase press the relevant button
until the text OFF appears on the display.
If your laundry load to be washed and dried is much
greater than the maximum stated load (see adjacent
table), perform the wash cycle, and when the cycle is
complete, divide the garments into groups and put some
of them back in the drum. At this point, follow the
instructions provided for a "Drying only" cycle. Repeat
this procedure for the remainder of the load.
N.B: a cooling-down period is always added to the end
of each drying cycle.
Drying only
Select a drying setting (
- - ) using the WASH
CYCLE selector in accordance with the type of fabric, then
select the desired drying type using the DRYING button.
Modifying the cycle settings.
Press the button to enable the function; the indicator
light corresponding to the button will switch on.
Press the button again to disable the function; the
indicator light will switch off.
If the selected function is not compatible with the
programmed wash cycle, the indicator light will flash and
the function will not be activated.
If the selected function is not compatible with another
function which has been selected previously, the indicator
light corresponding to the first function selected will flash
and only the second function will be activated; the indicator
light corresponding to the enabled function will remain lit.
The functions may affect the recommended load value
and/or the duration of the cycle.
7. START THE PROGRAMME. Press the START/
PAUSE button. The corresponding indicator light will
become green, remaining lit in a fixed manner, and the
door will be locked (the DOOR LOCKED symbol
will
be on). During the wash cycle, the name of the phase in
progress will appear on the display. To change a wash
cycle while it is in progress, pause the washer dryer
using the START/PAUSE button (the START/PAUSE
indicator light will flash slowly in an orange colour); then
select the desired cycle and press the START/PAUSE
button again.
To open the door while a cycle is in progress, press the
START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened. Press
the START/PAUSE button again to restart the wash
cycle from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE.This will be
indicated by the text "END OF CYCLE" on the display;
when the DOOR LOCKED
symbol switches off the
door may be opened. Open the door, unload the laundry
and switch off the machine.
If you wish to cancel a cycle which has already begun,
press and hold the
button. The cycle will be stopped
and the machine will switch off.
Fabric
type
Load type Max.
load
(kg)
Cupboard
dry
Henger
dry
Iron
dry
Cotton Clothing of different
sizes, Terry towels
5 180 170 160
Synthe-
tics
Sheets, Shirts, Pyjamas,
socks, etc.
3 180 170 160
Wool Knitwear, Pullovers, etc.
1,5 150 140 130
Table of Drying times (guideline values)
GB
9
Wash cycles and functions
Wash functions
Stain removal
This function is particularly useful for the removal of
stubborn stains.
Place extra compartment 4
(supplied) into
compartment 1. When
pouring in the bleach, be
careful not to exceed the
"max" level marked on the
central pivot (see figure).
To run the bleach cycle on its
own, pour the bleach into
extra compartment 4, set
the "Rinse" programme and
activate the "Stain removal" programme. To bleach during a
wash cycle, pour in the detergent and any fabric softener you
wish to use, set the desired wash cycle and enable the "Stain
removal" function.
The use of extra compartment 4 excludes the Pre-wash
function.
It cannot be used with the , , , Pump out and
Drying programmes.
Extra rinse
By selecting this option, the efficiency of the rinse is
increased and optimal detergent removal is guaranteed. It
is particularly useful for sensitive skin.
It cannot be used in conjunction with the , , Pump
out and Drying programmes.
For all Test Institutes:
* Test wash cycle in compliance with regulation EN 60456: set wash cycle with a temperature of 60°C.
Table of wash cycles
Easy iron
By selecting this function, the wash and spin cycles will be
modified in order to reduce the formation of creases. At
the end of the cycle the washer dryer will perform slow
rotations of the drum; the EASY IRON indicator light will
switch on, the START/PAUSE indicator light will flash in an
orange colour and the text "END OF CYCLE" will appear on
the display. To end the cycle, press the START/PAUSE
button or the EASY IRON button.
For the Silk/Curtains cycle, the machine will end the cycle
while the laundry is soaking; the EASY IRON indicator light
will switch on, the START/PAUSE indicator light will flash in
an orange colour and the text "STOP WITH WATER" will
appear on the display. To drain the water so that the
laundry may be removed, press the START/PAUSE button
or the EASY IRON button.
It may not be used with the , , , Pump out and
Drying programmes.
Mini load
This function is recommended for when the load of laundry
is equal to half, or less than half, of the maximum
recommended load (see Table of wash cycles).
It cannot be used with the , , Pump out and Drying
programmes.
MAX
1
2
4
3
Description of the wash cycle
Max
.
temp.
(°C)
Max.
speed
(rpm)
Dry
-
ing
Detergents Max. load (kg)
Cycle
duration
Bleach Wash
Fabric
softener
Normal
Mini
Load
Everyday wash cycles (Daily)
Cottons (*)
(1
st
press of the button)
:
extremely soiled whites.
90° 1200
lll l
73
Cottons
(2
nd
press of the button)
:
heavily soiled whites and resistant colours.
60° 1200
lll l
73
Cottons
(3
rd
press of the button)
:
heavily soiled whites and delicate colours.
40° 1200
lll l
73
Synthetics
(1
st
press of the button)
:
heavily soiled resistant colours.
60° 800
lll l
31,5
Synthetics
(2
nd
press of the button)
:
lightly soiled resistant colours.
40° 800
lll l
31,5
Mix 30'
(1
st
press of the button)
:
to refresh lightly soiled garments quickly
(not suitable for wool, silk and clothes which require washing by hand).
30° 800
l
-
ll
3 -
Mix 15'
(2
nd
press of the button)
:
to refresh lightly soiled garments quickly (not
suitable for wool, silk and clothes which require washing by hand).
30° 800
l
-
ll
1,5 -
Silk/Curtains:
for garments in silk and viscose, lingerie.
30° 0 - -
ll
11
Memory:
allows for any wash cycle to be stored.
Wool:
for wool, cashmere, etc.
40° 800
lll l
1,5 1
Drying programmes
Cotton dry
(1
st
press of the button)
- -
l
- - - 5 -
Synthetics dry
(2
st
press of the button)
- -
l
- - - 3 -
Wool dry
(3
st
press of the button)
- -
l
- - - 1,5 -
Partial wash cycles
Spin - 1200
l
- - - 7 -
Rinse
(1
st
press of the button)
- 1200
ll
-
l
73
Pump out
(2
nd
press of the button)
- 0 - - - - 7 -
The duration of the wash cycles can be checked
on the display.
Wash cycles
M
10
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance
and contribute to environmental pollution.
Do not use hand washing detergents because these
create too much foam.
Open the detergent
dispenser drawer and
pour in the detergent or
washing additive, as
follows.
compartment 1: Pre-wash detergent (powder)
Before pouring in the detergent, make sure that extra
compartment 4 has been removed.
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
extra compartment 4: Bleach
Preparing the laundry
Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from
whites
Empty all garment pockets and check the buttons.
Do not exceed the listed values, which refer to the
weight of the laundry when dry:
Durable fabrics: max. 7 kg
Synthetic fabrics: max. 3 kg
Delicate fabrics: max. 2 kg
Wool: max. 1.5 kg
Silk: max. 1 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
MAX
1
2
4
3
Special wash cycles
Mix 30: this wash cycle was designed to wash
lightly soiled garments quickly: it lasts just 30 minutes
and therefore saves both energy and time. By
selecting this wash cycle (
at 30°C), it is possible to
wash different fabrics together (except for wool and
silk items), with a maximum load of 3 kg.
Mix 15: this wash cycle was designed to wash
lightly soiled garments quickly: it lasts just 15 minutes
and therefore saves both energy and time. By
selecting this wash cycle (
at 30°C), it is possible to
wash different fabrics together (except for wool and
silk items), with a maximum load of 1.5 kg.
Silk: use special wash cycle
to wash all silk
garments. We recommend the use of special
detergent which has been designed to wash delicate
clothes.
Curtains: fold curtains and place them in a pillow
case or mesh bag. Use wash cycle
.
Wool: Scholtès is the only washer dryer
manufacturer to have been awarded the prestigious
Woolmark Platinum Care endorsement (M.0508) by
the Woolmark Company, which means that all
woollen garments may be washed in the washer
dryer, even those which state hand wash only
on the label. Wash cycle therefore offers complete
peace of mind when washing woollen garments in the
washer dryer (max. load 1.5 kg) and guarantees
optimal performance.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
and to distribute the load in a uniform manner, the
drum rotates continuously at a speed which is slightly
greater than the washing rotation speed. If, after
several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the
load is excessively unbalanced, the washer dryer
performs the distribution process instead of spinning.
To encourage improved load distribution and balance,
we recommend small and large garments are mixed
in the load.
GB
11
Precautions and tips
This washer dryer was designed and constructed in
accordance with international safety regulations. The
following information is provided for safety reasons
and must therefore be read carefully.
General safety
This appliance was designed for domestic use only.
The washer dryer must only be used by adults, in
accordance with the instructions provided in this manual.
Do not touch the machine when barefoot or with
wet or damp hands or feet.
Do not pull on the power supply cable when
unplugging the appliance from the electricity
socket. Hold the plug and pull.
Do not open the detergent dispenser drawer while
the machine is in operation.
Do not touch the drained water as it may reach
extremely high temperatures.
Never force the porthole door. This could damage
the safety lock mechanism designed to prevent
accidental opening.
If the appliance breaks down, do not under any
circumstances access the internal mechanisms in
an attempt to repair it yourself.
Always keep children well away from the appliance
while it is operating.
The door can become quite hot during the wash cycle.
If the appliance has to be moved, work in a group
of two or three people and handle it with the utmost
care. Never try to do this alone, because the
appliance is very heavy.
Before loading laundry into the washer dryer, make
sure the drum is empty.
During the drying phase, the door tends to get
quite hot.
Do not use the appliance to dry clothes that have
been washed with flammable solvents (e.g.
trichlorethylene).
Do not use the appliance to dry foam rubber or
similar elastomers.
Make sure that the water tap is turned on during
the drying cycles.
Disposal
Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
Opening the porthole door manually
In the event that it is not possible to open the
porthole door due to a powercut, and if you wish to
remove the laundry, proceed as follows:
1. remove the plug from the electrical socket.
2. make sure the water level inside the machine is
lower than the door opening; if it is not, remove
excess water using the drain hose, collecting it in a
bucket.
3. pull outwards using the tab as indicated in the
figure, until the plastic tie-rod is freed from its stop
position; pull downwards and open the door at the
same time.
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out "wheeled bin" symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
12
GB
Care and maintenance
Cutting off the water and electricity
supplies
Turn off the water tap after every wash cycle. This
will limit wear on the hydraulic system inside the
washer dryer and help to prevent leaks.
Unplug the washer dryer when cleaning it and
during all maintenance work.
Cleaning the washer dryer
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth soaked
in lukewarm soapy water. Do not use solvents or
abrasives.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and pulling it
out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of your
appliance
Always leave the porthole door ajar in order to
prevent unpleasant odours from forming.
Cleaning the pump
The washer dryer is fitted with a self-cleaning pump
which does not require any maintenance.
Sometimes, small items (such as coins or buttons)
may fall into the pre-chamber which protects the
pump, situated in its bottom part.
Make sure the wash cycle has finished and
unplug the appliance.
1
2
To access the pre-chamber:
1. unscrew the lid by
rotating it anti-clockwise
(see figure): a little water
may trickle out. This is
perfectly normal;
2. clean the inside thoroughly;
3. screw the lid back on;
Checking the water inlet hose
Check the inlet hose at least once a year. If there are
any cracks, it should be replaced immediately: during
the wash cycles, water pressure is very strong and a
cracked hose could easily split open.
Never use second-hand hoses.
GB
13
Troubleshooting
Your washer dryer could fail to work. Before contacting the Technical Assistance Centre (see Assistance), make
sure that the problem cannot be not solved easily using the following list.
Problem:
The washer dryer does not
switch on.
The wash cycle does not start.
The washer dryer does not take
in water (the text "NO WATER,
CHECK SUPPLY" appears
on the display).
The washer dryer continuously
takes in and
drains water.
The washer dryer does not drain
or spin.
The washer dryer vibrates a lot
during the spin cycle.
The washer dryer leaks.
The machine is locked and the
display flashes, indicating an
error code (e.g. F-01, F-..).
There is too much foam.
The washer-dryer does not dry.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or is not making contact.
There is no power in the house.
The washer dryer door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set (see How to run a wash cycle or a drying cycle).
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The drain hose is not fitted at a height between 65 and 100 cm from
the floor (see Installation).
The free end of the hose is under water (see Installation).
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap,
switch the appliance off and contact the Assistance Service. If the
dwelling is on one of the upper floors of a building, there may be problems
relating to water drainage, causing the washer dryer to fill with water and
drain continuously. Special anti-draining valves are available in shops and
help to avoid this inconvenience.
The wash cycle does not include draining: some wash cycles require the
drain phase to be started manually (see Wash cycles and functions).
The EASY IRON function has been activated: To complete the wash
cycle, press the START/PAUSE button (see Wash cycles and functions).
The drain hose is bent (see Installation).
The drainage duct is clogged.
The drum was not unlocked correctly during installation (see Installation).
The washer dryer is not level (see Installation).
The washer dryer is trapped between cabinets and walls (see Installation).
The water inlet hose is not screwed on properly (see Installation).
The detergent dispenser drawer is blocked (for cleaning instructions, see Care
and maintenance).
The drain hose is not fixed properly (see Installation).
Switch off the machine and unplug it, wait for approximately 1 minute
and then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
The detergent is not suitable for machine washing (it should display the
text for washer dryers or hand and machine wash, or the like).
Too much detergent was used.
The appliance is not plugged into the socket, or not enough to make contact.
There has been a power failure.
The appliance door is not shut properly.
A delayed start has been set.
DRYING is in the OFF position.
14
GB
Service
Before calling for Assistance:
Check whether you can solve the problem alone (see Troubleshooting);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Assistance Centre using the telephone number
provided on the guarantee certificate.
Always request the assistance of authorised technicians.
Have the following information to hand:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate applied to the rear of the washer dryer, and can also be
found on the front of the appliance by opening the door.
FR
15
Français
Sommaire
Installation, 16-17-18-19
Déballage et mise à niveau
Raccordements eau et électricité
Premier cycle de lavage
Caractéristiques techniques
Instructions pour l'installateur
Description du lavante-séchante, 20-21
Bandeau de commandes
Écran
Comment effectuer un cycle de lavage
ou un séchage, 22
Programmes et fonctions, 23
Tableau des programmes
Fonctions de lavage
Produits lessiviels et linge, 24
Tiroir à produits lessiviels
Triage du linge
Programmes spéciaux
Système déquilibrage de la charge
Précautions et conseils, 25
Sécurité générale
Mise au rebut
Ouverture manuelle de la porte hublot
Entretien et soin, 26
Coupure de larrivée deau et du courant
Nettoyage du lavante-séchante
Nettoyage du tiroir à produits lessiviels.
Entretien du hublot et du tambour
Nettoyage de la pompe
Contrôle du tuyau darrivée de leau
Anomalies et remèdes, 27
Assistance, 28
FR
SDLE 129
Mode demploi
LAVANTE-SÉCHANTE
16
FR
A
Installation
Conserver ce mode demploi pour pouvoir le
consulter à tout moment. En cas de vente, de
cession ou de déménagement, veiller à ce quil suive
toujours le lavante-séchante pour que son nouveau
propriétaire soit informé sur son mode de
fonctionnement et puisse profiter des conseils
correspondants.
Lire attentivement les instructions: elles fournissent
des conseils importants sur linstallation, lutilisation et
la sécurité de lappareil.
Déballage et mise à niveau
Déballage
1. Déballer le lavante-séchante.
2. Contrôler que le lavante-séchante na pas été
endommagé pendant le transport. Sil est abîmé, ne
pas le raccorder et contacter le vendeur.
3. Enlever les 4 vis de
protection servant au
transport, le caoutchouc
et la cale, placés dans la
partie arrière (voir figure).
4. Boucher les trous à laide des bouchons plastique
fournis.
5. Conserver toutes ces pièces: il faudra les remonter
en cas de transport du lavante-séchante.
Les pièces demballage ne sont pas des jouets pour
enfants.
Mise à niveau
1. Installer le lavante-séchante sur un sol plat et
rigide, sans lappuyer contre des murs, des meubles
ou autre.
2. Si le sol nest pas
parfaitement horizontal,
visser ou dévisser les
pieds de réglage avant
(voir figure) pour niveler
lappareil; son angle
dinclinaison, mesuré sur
le plan de travail, ne doit
pas dépasser 2°.
Une bonne mise à niveau garantit la stabilité de
lappareil et évite quil y ait des vibrations, du bruit et
des déplacements en cours de fonctionnement. Si la
machine est posée sur de la moquette ou un tapis,
régler les pieds de manière à ce quil y ait
suffisamment despace pour assurer une bonne
ventilation.
Raccordements eau et électricité
Raccordement du tuyau darrivée de leau
1. Monter le joint A sur
lextrémité du tuyau
dalimentation et le visser
à un robinet deau froide
à embout fileté 3/4 gaz
(voir figure).
Faire couler leau jusquà
ce quelle soit limpide et
sans impuretés avant de
raccorder.
2. Raccorder le tuyau
darrivée de leau au
lavante-séchante en le
vissant à la prise deau
prévue, dans la partie
arrière en haut à droite
(voir figure).
3. Attention à ce que le tuyau ne soit pas plié ou
écrasé.
La pression de leau doit être comprise entre les
valeurs indiquées dans le tableau des Caractéristiques
techniques (voir page ci-contre).
Si la longueur du tuyau dalimentation ne suffit pas,
sadresser à un magasin spécialisé ou à un technicien
agréé.
Nutiliser que des tuyaux neufs.
Utiliser ceux qui sont fournis avec lappareil.
FR
17
65 - 100 cm
Raccordement du tuyau de vidange
Raccorder le tuyau
dévacuation, sans le
plier, à un conduit
dévacuation ou à une
évacuation murale placés
à une distance du sol
comprise entre 65 et 100
cm;
ou bien laccrocher à un
évier ou à une baignoire,
dans ce cas, fixer le
support en plastique
fourni avec lappareil au
robinet (voir figure).
Lextrémité libre du tuyau
dévacuation ne doit pas
être plongée dans leau.
Lutilisation dun tuyau de rallonge est absolument
déconseillée mais si on ne peut faire autrement, il faut
absolument quil ait le même diamètre que le tuyau
original et sa longueur ne doit pas dépasser 150 cm.
Branchement électrique
Avant de brancher la fiche dans la prise de courant,
sassurer que:
la prise est bien reliée à la terre et est conforme aux
réglementations en vigueur;
la prise est bien apte à supporter la puissance
maximale de lappareil indiquée dans le tableau des
Caractéristiques techniques (voir ci-contre);
la tension dalimentation est bien comprise entre les
valeurs figurant dans le tableau des Caractéristiques
techniques (voir ci-contre);
la prise est bien compatible avec la fiche du lavan-
te-séchante. Autrement, remplacer la prise ou la
fiche.
Le lavante-séchante ne doit pas être installé dehors,
même à labri, car il est très dangereux de le laisser
exposé à la pluie et aux orages.
Après installation du lavante-séchante, la prise de
courant doit être facilement accessible.
Nutiliser ni rallonges ni prises multiples.
Le câble ne doit être ni plié ni trop écrasé.
Le câble dalimentation ne doit être remplacé que
par des techniciens agréés.
Attention! Nous déclinons toute responsabilité en cas
de non-respect des normes énumérées ci-dessus.
Premier cycle de lavage
Avant la première mise en service de lappareil,
effectuer un cycle de lavage avec un produit lessiviel
mais sans linge et sélectionner le programme
.
Caractéristiques techniques
Modèle
SDLE 129
Dimensions
largeur 59,5 cm
hauteur 81,5 cm
profondeur 54,5 cm
Capacité
de 1 à 7 kg pour le lavage
de 1 à 5 kg pour lechage
Raccordements
électriques
Voir la plaque signalétique appliquée
sur la machine
Raccordements
hydrauliques
pression maximale 1 MPa (10 bar)
pression minimale 0,05 MPa (0,5 bar)
capacité du tambour 52 litres
Vitesse
d'essorage
jusqu 1200 tours minute
Programmes de
contrôle selon la
norme EN 50229
lavage: programme
(1° pression de
la touche)
; température 60°C;
effectué avec une charge de 7 kg.
séchage: premierchage effectué
avec 2 kg de charge en sélectionnant
le niveau dechage "A REPASSER";
deuxième séchage effectué avec 5 kg
de charge en sélectionnant le niveau
de séchage "A RANGER".
Cet appareil est conforme aux
Directives Communautaires suivantes:
- 89/336/CEE du 03/05/89
(Compatibilité électromagnétique) et
modifications suivantes
- 2002/96/CE
- 2006/95/CE (Basse Tension)
18
FR
Instructions pour l'installateur
Application du panneau d'habillage en bois sur
la porte et montage du machine à laver à
l'intérieur des éléments:
Au cas où, après le montage du panneau en bois, il faudrait
expédier la machine pour son installation finale, nous vous
conseillons de la laisser dans son emballage d'origine.
L'emballage a été justement réalisé de manière à permettre
le montage du panneau en bois sur la machine sans
déballer complètement le produit (voir figures ci-dessous).
Le panneau en bois couvrant la façade ne doit pas avoir
plus de 18 mm d'épaisseur, il peut être articulé tant à
droite qu'à gauche. Pour plus de facilité d'emploi, nous
conseillons d'adopter le même sens d'ouverture que pour
le hublot dont les charnières sont montées sur le côté
gauche.
A
B
C
D
E
Tur seite
Accessoires montage porte (Fig.1-2-3-4-5).
Fig. 1
N°2 Charnière
N°1 Aimant N°1 Butoir aimant
N°1 Cheville en
caoutchouc
N°2 Supports charnière
N°4 Cales
Fig. 2
Fig. 3 Fig. 4
Fig. 5
Fig. 4/B
- 6 vis autotaraudeuses l = 13 mm "type A".
- 2 vis métriques à tête évasée l = 25 mm "type B"; pour
fixation du butoir aimant au meuble.
- 4 vis métriques l = 15 mm "type C"; pour montage des
supports charnière au meuble.
- 4 vis métriques l = 7 mm "type D"; pour montage des
charnières aux supports.
Montage des pièces sur la façade de la machine.
- Montez les supports de la charnière sur la façade, en
positionnant le trou indiqué par une flèche dans la fig. 1
vers lintérieur de la façade et interposez une cale (fig. 4/B).
Utilisez les vis type C.
- Montez le butoir aimant du côté opposé en haut et
interposez deux cales (fig. 4/B). Utilisez les deux vis type B.
FR
19
Utilisation du gabarit de forage.
- Pour marquer l'emplacement des trous sur le côté du
panneau, alignez le gabarit de perçage avec le côté
supérieur gauche du panneau en vous servant des lignes
tracées aux extrémités.
- Pour marquer l'emplacement des trous sur le côté droit
du panneau, alignez le gabarit de perçage avec le côté
supérieur droit du panneau.
- Réalisez à l'aide d'une fraise appropriée les quatre
emplace-ments devront trouver place les deux
charnières, la cheville en caoutchouc et l'aimant.
Montage des pièces sur le panneau en bois (Porte).
- Montez les charnières aux emplacements prévus (la
partie mobile de la charnière doit se trouver vers l'extérieur
du panneau) et fixez-les à l'aide de 4 vis type A.
- Montez l'aimant à son emplacement en haut, à l'opposé
des charnières et fixez-le au moyen de deux vis type B.
- Montez la cheville en caoutchouc à sa place en bas.
Le panneau est à présent prêt, vous pouvez le monter sur
la machine.
Montage du panneau sur la machine.
Introduisez l'ergot de la charnière indiqué par la flèche fig. 2
dans le logement du support charnière, poussez le panneau
vers la façade de la machine et fixez les deux charnières à
l'aide des deux vis type D.
Fixation du support de la base.
Si la machine est installée à une extrémité de la cuisine
intégrée, montez une ou les deux glissières du socle
comme illustré fig. 8 en réglant leur profondeur en
fonction de la position du socle et, au besoin, fixez-le à
ces dernières fig. 9. Pour monter le support de la base,
procédez comme suit (fig. 8): Fixez l'équerre P à l'aide de
la vis R, insérez le support de la base Q dans la fente
prévue et après l'avoir dûment positionné bloquez-le à
l'aide de l'équerre d'assemblage P et de la vis R.
Montage de la machine à l'intérieur des éléments.
- Poussez la machine à travers l'ouverture en l'alignant
aux autres meubles (fig. 6).
- Servez-vous des pieds de réglage pour amener la
machine à la hauteur désirée.
- Pour régler la position du panneau en bois à la verticale et à
l'horizontale, servez-vous des vis C et D comme illustré fig. 7.
Important: fermez la partie inférieure de la façade, la base
touchant au sol.
Fig. 8 Fig. 9
Accessoires fournis pour le réglage de la hauteur.
Vous trouverez à l'intérieur du couvercle en polystyrène (fig. 10):
2 traverses (G); 1 listel (M);
et à l'intérieur du tambour :
4 pieds supplémentaires (H),
4 vis (I),
4 vis (R),
4 écrous (L),
2 supports pour la base (Q)
Réglage de la machine en hauteur.
La machine peut être réglée en hauteur (de 815 mm à 835
mm) à l'aide de ses 4 pieds.
Si vous souhaitez l'amener à une hauteur supérieure à celle
qui est indiquée plus haut, c'est à dire jusqu'à 870 mm,
utilisez les accessoires suivants :
les 2 traverses (G); les 4 pieds (H); les 4 vis (I); les 4 écrous
(L) puis procédez comme suit (fig. 11):
démontez les 4 pieds originaux, positionnez une traverse G
dans la partie avant de la machine, fixez-la à l'aide des vis I
(en les vissant dans les trous étaient fixés les pieds
originaux) puis montez les nouveaux pieds H.
Procédez de même dans la partie arrière de la machine.
Vous pouvez alors régler les pieds H pour élever ou abaisser
la machine de 835 mm à 870 mm.
Après avoir atteint la hauteur désirée, bloquez les écrous L à
la traverse G.
Pour régler la machine à une hauteur comprise entre 870
mm et 900 mm, montez le listel M et réglez les pieds H
jusqu'à la hauteur souhaitée.
Pour monter le listel, procédez comme suit:
desserrez les trois vis N situées dans la partie avant du couvercle,
montez le listel M comme illustré fig. 12 et serrez les vis N.
D
C
C
570
min
815
540
595
820 ÷ 900
600 min
Fig. 6 Fig. 7
L
I
H
G
M
Fig. 11 Fig. 12
Fig. 10
20
FR
Tiroir à produits lessiviels: pour charger les
produits lessiviels et les additifs (voir Produits lessiviels
et linge).
Tasto MARCHE/ARRÊT
: appuyer brièvement sur la
touche pour allumer ou éteindre l'appareil. Le voyant
vert MISE EN MARCHE/PAUSE clignotant lentement
indique que la machine est allumée. Pour éteindre le
lavante-séchante en cours de lavage, appuyer sur la
touche pendant au moins 2 secondes de suite ; une
pression brève ou accidentelle n'entraîne pas l'arrêt de
l'appareil. L'arrêt de l'appareil pendant un lavage
annule le lavage en cours.
Touches SÉLECTEUR PROGRAMMES: pour
sélectionner le programme désiré (voir "Tableau des
programmes").
Touche MEMO: maintenir la touche enfoncée pour
mémoriser un cycle et les personnalisations préférées.
Pour retourner à un cycle précédemment mémorisé,
appuyer sur la touche MEMO.
Touches FONCTION: appuyer sur la touche pour
sélectionner la fonction désirée. Le voyant
correspondant s'affiche à l'écran.
Touche ESSORAGE
: appuyer sur cette touche
pour diminuer la vitesse de l'essorage ou pour le
supprimer complètement - la valeur correspondante
s'affiche à l'écran.
Touche TEMPERATURE
: appuyer pour diminuer
la température: la valeur correspondante est affichée
à l'écran.
Touche VERROUILLAGE TOUCHES
: pour
activer le verrouillage des commandes, garder la
touche enfoncée pendant environ 2 secondes. Le
symbole
allumé indique que le bandeau de
commandes est verrouillé. Ceci permet d'éviter toute
modification involontaire des programmes, surtout s'il
y a des enfants à la maison. Pour désactiver le
verrouillage des commandes, garder la touche
enfoncée pendant environ 2 secondes.
Touche DÉPART DIFFÉRÉ
: appuyer sur cette
touche pour sélectionner un départ différé pour le
programme choisi. Le retard est affiché à l'écran.
Touche SÉCHAGE
: appuyer pour sélectionner un
cycle de séchage.
Touche avec voyant MISE EN MARCHE/PAUSE:
quand le voyant vert clignote lentement, appuyer sur
la touche pour démarrer un lavage. Une fois le cycle
lancé, le voyant passe à l'allumage fixe. Pour activer
une pause de lavage, appuyer à nouveau sur la
touche ; le voyant passe à l'orange et se met à
clignoter. Si le symbole
n'est pas allumé, il est
possible d'ouvrir le hublot. Pour faire redémarrer le
lavage exactement à l'endroit de l'arrêt, appuyer une
nouvelle fois sur la touche.
Description du lavante-séchante
Bandeau de commandes
Touche avec
voyant
MISE
EN MARCHE/
PAUSE
Touche
TEMPÉRATURE
Touches
SÉLECTEUR
PROGRAMMES
Tiroir à produits lessiviels
Touches
FONCTION
Touche
MARCHE/ARRÊT
Touche
ESSORAGE
Touche
SÉCHAGE
Écran
Touche
DÉPART
DIFFÉRÉ
Touche
MEMO
Touche
VERROUILLAGE
TOUCHES
1 / 1

Indesit SDLE 129 (EU) Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire
Ce manuel convient également à