Indesit SDLE 129 (EU) Le manuel du propriétaire

Marque: Indesit

Modèle: SDLE 129 (EU)

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Ce manuel convient également à

sdle 129 eu full

English,1

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Instructions for the fitter

Description of the washer dryer, 6-7

Control panel

Display

How to run a wash cycle or a drying cycle, 8

Wash cycles and functions, 9

Table of wash cycles

Wash functions

Detergents and laundry, 10

Detergent dispenser drawer

Preparing the laundry

Special wash cycles

Load balancing system

Precautions and tips, 11

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 12

Cutting off the water or electricity supply

Cleaning the washer dryer

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 13

Service, 14

SDLE 129

Instructions for use

WASHER DRYER

Español,29Français,15

Installation

 This instruction manual should be kept in a safe

place for future reference. If the washer dryer is sold,

transferred or moved, make sure that the instruction

manual remains with the machine so that the new

owner is able to familiarise himself/herself with its

operation and features.

 Read these instructions carefully: they contain vital

information relating to the safe installation and

operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washer dryer from its packaging.

2. Make sure that the washer dryer has not been

damaged during the transportation process. If it has

been damaged, contact the retailer and do not

proceed any further with the installation process.

3. Remove the 4

protective screws (used

during transportation) and

the rubber washer with

the corresponding

spacer, located on the

rear part of the appliance

(see figure).

4. Close off the holes using the plastic plugs provided.

5. Keep all the parts in a safe place: you will need

them again if the washer dryer needs to be moved to

another location.

 Packaging materials should not be used as toys for

children.

Levelling

1. Install the washer dryer on a flat sturdy floor,

without resting it up against walls, furniture cabinets

or anything else.

2. If the floor is not

perfectly level, compen-

sate for any unevenness

by tightening or loosening

the adjustable front feet

(see figure); the angle of

inclination, measured in

relation to the worktop,

must not exceed 2°.

Levelling the machine correctly will provide it with

stability, help to avoid vibrations and excessive noise

and prevent it from shifting while it is operating. If it is

placed on carpet or a rug, adjust the feet in such a

way as to allow a sufficient ventilation space

underneath the washer dryer.

Connecting the electricity and water

supplies

Connecting the water inlet hose

1. Insert seal A into the

end of the inlet hose and

screw the latter onto a

cold water tap with a 3/4

gas threaded opening

(see figure).

Before performing the

connection, allow the

water to run freely until it

is perfectly clear.

2. Connect the inlet hose

to the washer dryer by

screwing it onto the

corresponding water inlet

of the appliance, which is

situated on the top right-

hand side of the rear part

of the appliance (see

figure).

3. Make sure that the hose is not folded over or bent.

 The water pressure at the tap must fall within the

values indicated in the Technical details table (see

next page).

 If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

 Never use second-hand hoses.

 Use the ones supplied with the machine.

Te ch n i c a l d a t a

Model

SDLE 129

Dimensions

width 59.5 cm

height 81,5 cm

depth 54,5 cm

Capacity

from 1 to 7 kg for the wash programme;

from 1 to 5 kg for the drying programme

Electrical

connections

please refer to the technical data plate

fixed to the machine

Water

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed

up to 1200 rotations per minute

Energy rated

programmes

according to

regulation

EN 50229

Wash:

programme

press of the

button); temperature 60°C;

using a load of 7 kg.

Drying: first drying cycle performed with a

2 kg load, by selecting the "IRON DRY"

dryness level;

The second drying cycle is performed

with a 5 kg load, by selecting the

"CUPBORD DRY" dryness level.

This appliance conforms to the following

EC Directives:

- 89/336/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent modifications

- 2002/96/EC

- 2006/95/EC (Low Voltage)

65 - 100 cm

Connecting the drain hose

Connect the drain hose,

without bending it, to a

drainage duct or a wall

drain located at a height

between 65 and 100 cm

from the floor;

alternatively, rest it on

the side of a washbasin

or bathtub, fastening the

duct supplied to the tap

(see figure). The free end

of the hose should not

be underwater.

 We advise against the use of hose extensions; if it is

absolutely necessary, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the electricity

socket, make sure that:

 the socket is earthed and complies with all

applicable laws;

 the socket is able to withstand the maximum power

load of the appliance as indicated in the Technical

data table (see opposite);

 the power supply voltage falls within the values

indicated in the Technical data table (see opposite);

 the socket is compatible with the plug of the

washer dryer. If this is not the case, replace the

socket or the plug.

 The washer dryer must not be installed outdoors,

even in covered areas. It is extremely dangerous to

leave the appliance exposed to rain, storms and other

weather conditions.

 When the washer dryer has been installed, the

electricity socket must be within easy reach.

 Do not use extension cords or multiple sockets.

 The cable should not be bent or compressed.

 The power supply cable must only be replaced by

authorised technicians.

Warning! The company shall not be held responsible

in the event that these regulations are not respected.

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, using the wash cycle

Instructions for the fitter

Mounting the wooden panel onto the door and

inserting the machine into cabinets:

In the case where the machine must be shipped for final

installation after the wooden panel has been mounted, we

suggest leaving it in its original packaging. The packaging

was designed to make it possible to mount the wooden

panel onto the machine without removing it completely

(see figures below).

The wooden panel that covers the face of the machine

must not be less than 18 mm in thickness and can be

hinged on either the right or left. For the sake of

practicality when using the machine, we recommend that

the panel be hinged on the same side as the door for the

machine itself - the left.

Tur seite

Door Mounting Accessories (Fig. 1-2-3-4-5).

Fig. 1

N° 2 Hinges

N° 1 Magnet N° 1 Magnet plate

N° 1 Rubber plug

N° 2 Hinge Supports

N° 4 Spacers

Fig. 2

Fig. 3 Fig. 4

Fig. 5

Fig. 4/B

- No. 6 type A self-threading screws, l =13 mm.

- No. 2 type B metric, countersunk screws, l =25; for

fastening the magnet plate to the cabinet.

- No. 4 type C metric screws, l =15 mm; for mounting the

hinge supports to the cabinet.

- No. 4 type D metric screws, l =7 mm; for mounting the

hinges on the supports.

Mounting the Parts onto the Face of the Machine.

- Fit the hinge supports to the appliance front panel,

positioning the hole marked with an arrow in fig. 1 so that it

is on the inner side of the front panel. Fit a spacer (fig. 4/B)

between the surfaces using type C screws.

- Fit the magnet plate at the top of the opposite side,

using type B screws to fix two spacers (fig. 4/B) between

the plate and the surface.

Using the Drilling Template.

- To trace the positions of the holes on the left-hand side

of the panel, align the drilling template to the top left side

of the panel using the lines traced on the extremities as a

reference.

- To trace the positions of the holes on the right-hand

side of the panel, align the drilling template to the top

right side of the panel.

- Use an appropriately sized router to mill the holes for

the two hinges, the rubber plug and the magnet.

Mounding the Parts onto the Wooden Panel (Door).

- Insert the hinges into the holes (the movable part of the

hinge must be positioned facing away from the panel) and

fasten them with the 4 type A screws.

- Insert the magnet into the top hole on the opposite side

of the hinges and fasten it with the two type B screws.

- Insert the rubber plug into the bottom hole.

The panel is now ready to be mounted onto the machine.

Mounting the Panel into the machine.

Insert the nib of the hinge (indicated by the arrow in fig. 2)

into the hole for the hinge and push the panel towards the

front of the machine. Fasten the two hinges with the type

D screws.

Fastening the plinth guide.

If the machine is installed at the end of a set of modular

cabinets, mount either one or both of the guides for the

base molding (as shown in fig. 8). Adjust them for depth

based on the position of the base molding, and, if

necessary, fasten the base to the guides (fig. 9).

This is how to assemble the plinth guide (fig. 8):

Fasten angle P using screw R, insert plinth guide Q into

the special slot and once it is in the desired position, lock

it in place using angle P and screw R.

Inserting the machine into the Cabinet.

- Push the machine into the opening, aligning it with the

cabinets (fig. 6).

- Regulate the adjustable feet to raise the machine to the

appropriate height.

- To adjust the position of the wooden panel in both the

vertical and horizontal directions, use the C and D

screws, as shown in fig. 7.

Important: close the lower part of the appliance front by

ensuring that the plinth rests against the floor.

Fig. 8 Fig. 9

Accessories provided for the height adjustment.

The following can be found inside the polystyrene lid (fig. 10):

2 crossbars (G), 1 strip (M)

the following can be found inside

the appliance drum:

4 additional feet (H),

4 screws (I),

4 screws (R),

4 nuts (L),

2 plinth guides (Q)

Adjusting the appliance height.

The height of the appliance can be adjusted (from 815 mm

to 835 mm), by turning the 4 feet.

Should you require the appliance to be placed higher than

the above height, you need to use the following accessories

to raise it to up to 870 mm:

the two crossbars (G); the 4 feet (H); the 4 screws (I); the 4

nuts (L) then perform the following operations (fig. 11):

remove the 4 original feet, place a crossbar G at the front of

the appliance, fastening it in place using screws I (screwing

them in where the original feet were) then insert the new feet H.

Repeat the same operation at the back of the appliance.

Now adjust feet H to raise or lower the appliance from 835

mm to 870 mm.

Once you have reached the desired height, lock nuts L onto

crossbar G.

To adjust the appliance to a height between 870 mm and

900 mm, you need to mount strip M, adjusting feet H to the

required height.

Insert the strip as follows:

loosen the three screws N situated at the front of the Top

cover of the appliance, insert strip M as shown in fig. 12,

then fasten screws N.

570

min

815

540

595

820 ÷ 900

600 min

Fig. 6 Fig. 7

Fig. 11 Fig. 12

Fig. 10

Detergent dispenser drawer: used to dispense

detergents and washing additives (see Detergents

and laundry).

ON/OFF button

: press this briefly to switch the

machine on or off. The START/PAUSE indicator light,

which flashes slowly in a green colour shows that the

machine is switched on. To switch off the washer

dryer during the wash cycle, press and hold the

button for approximately 2 seconds; if the button is

pressed briefly or accidentally the machine will not

switch off. If the machine is switched off during a

wash cycle, this wash cycle will be cancelled.

WASH CYCLE SELECTOR buttons: used to set the

desired wash cycle (see "Table of wash cycles").

MEMORY button: press and hold the button to store

a cycle with your own set of preferences in the

memory of the machine. To recall a previously stored

cycle, press the MEMO button.

FUNCTION buttons: press the button to select the

desired function. The corresponding indicator light on

the display will switch on.

SPIN button

: press to reduce or completely

exclude the spin cycle - the value is indicated on the

display.

TEMPERATURE button

: press to decrease the

temperature: the value will be shown on the display.

CONTROL PANEL LOCK button

: to activate the

control panel lock, press and hold the button for

approximately 2 seconds. When the symbol

illuminated, the control panel is locked. This means it

is possible to prevent wash cycles from being modified

accidentally, especially where there are children in the

home. To deactivate the control panel lock, press

and hold the button for approximately 2 seconds.

DELAYED START button

: press to set a delayed

start time for the selected wash cycle. The delay time

will be shown on the display.

DRYING button

: press to set a drying cycle.

START/PAUSE button with indicator light: when the

green indicator light flashes slowly, press the button to

start a wash cycle. Once the cycle has begun the

indicator light will remain lit in a fixed manner. To

pause the wash cycle, press the button again; the

indicator light will flash in an orange colour. If the

symbol

is not illuminated, the door may be

opened. To start the wash cycle from the point at

which it was interrupted, press the button again.

Description of the washer dryer

Control panel

TEMPERATURE

Button

WASH

CYCLE

SELECTOR

Buttons

Detergent dispenser drawer

FUNCTION

buttons

ON/OFF

button

SPIN SPEED

Button

START/PAUSE

button with

indicator light

DRYING

Button

DISPLAY

DELAYED

START

Button

MEMORY

Button

CONTROL PANEL

LOCK

button

Display

The display is useful when programming the machine and provides a great deal of information.

The upper two strings A and B are used to display the selected wash cycle or the type of drying selected, the

current wash cycle phase (the selected dryness level or drying time) and all the indications relating to the progress

status of the cycle.

String C shows the time remaining until the end of the wash cycle in progress and, if a DELAYED START has been

set, the time remaining until the start of the selected wash cycle.

String D shows the maximum spin speed value (this depends on the selected wash cycle); if the wash cycle does

not include a spin cycle, the string remains unused.

String E shows the maximum temperature value which may be selected (this depends on the wash cycle used); if

the temperature of the wash cycle cannot be modified, the string remains unused.

Indicator lights F correspond to the functions and light up when the selected function is compatible with the set

wash cycle.

Door locked symbol

If the symbol is lit, this indicates that the washer dryer door is blocked to prevent it from being opened

accidentally. To prevent any damage from occurring, wait for the symbol to switch itself off before opening the

appliance door.

N.B.: if the DELAYED START function has been activated, the door cannot be opened; pauses the machine by

pressing the START/PAUSE button if you wish to open it.

 The first time the machine is switched on, you will be asked to select the language and the display will

automatically show the language selection menu.

To select the desired language press the TEMPERATURE and SPIN buttons; to confirm the selection press the

DRYING button.

If you wish to select another language, press and hold the DRYING + TEMPERATURE + SPIN buttons

simultaneously for 5 seconds, then repeat the steps listed above.

How to run a wash cycle or a

drying cycle

1. SWITCH THE MACHINE ON.Press the button; the

text WELCOME will appear on the display and the START/

PAUSE indicator light will flash slowly in a green colour.

2. LOAD THE LAUNDRY. Open the porthole door. Load

the laundry, making sure you do not exceed the

maximum load value indicated in the table of

programmes on the following page.

3. MEASURE OUT THE DETERGENT. Pull out the

detergent dispenser drawer and pour the detergent into

the relevant compartments as described in "Detergents

and laundry".

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Press one of the WASH

CYCLE SELECTOR buttons to select the required wash

cycle; the name of the wash cycle will appear on the

display. A temperature and spin speed is set for each

wash cycle; these may be adjusted. The duration of the

cycle will appear on the display.

6. CUSTOMISE THE WASH CYCLE. Use the relevant

buttons:

Modifying the temperature and/or spin

speed.The machine automatically selects the maximum

temperature and spin speed set for the selected wash

cycle; these values cannot therefore be increased. The

temperature can be decreased by pressing the

button, until the cold wash "OFF" setting is reached. The

spin speed may be progressively reduced by pressing

the

button, until it is completely excluded (the "OFF"

setting). If these buttons are pressed again, the

maximum values are restored.

Setting a delayed start.

To set a delayed start for the selected programme,

press the corresponding button repeatedly until the

required delay period has been reached. When this

option is enabled, the

symbol lights up on the

display. To remove the delayed start function press the

button until the text "OFF" appears on the display.

Setting the drying cycle.

The desired drying cycle type may be set by pressing

the DRYING button once or several times. Two options

are available:

A - Based on the how damp the clothes are once they

have been dried:

Iron dry: slightly damp clothes, easy to iron.

Hanger dry: dry clothes to put away.

Cupboard dry: very dry clothes, recommended for

towelling and bathrobes.

B - Based on time: from 40 minutes to 180.

To exclude the drying phase press the relevant button

until the text OFF appears on the display.

If your laundry load to be washed and dried is much

greater than the maximum stated load (see adjacent

table), perform the wash cycle, and when the cycle is

complete, divide the garments into groups and put some

of them back in the drum. At this point, follow the

instructions provided for a "Drying only" cycle. Repeat

this procedure for the remainder of the load.

N.B: a cooling-down period is always added to the end

of each drying cycle.

Drying only

Select a drying setting (

- - ) using the WASH

CYCLE selector in accordance with the type of fabric, then

select the desired drying type using the DRYING button.

Modifying the cycle settings.

 Press the button to enable the function; the indicator

light corresponding to the button will switch on.

 Press the button again to disable the function; the

indicator light will switch off.

 If the selected function is not compatible with the

programmed wash cycle, the indicator light will flash and

the function will not be activated.

 If the selected function is not compatible with another

function which has been selected previously, the indicator

light corresponding to the first function selected will flash

and only the second function will be activated; the indicator

light corresponding to the enabled function will remain lit.

 The functions may affect the recommended load value

and/or the duration of the cycle.

7. START THE PROGRAMME. Press the START/

PAUSE button. The corresponding indicator light will

become green, remaining lit in a fixed manner, and the

door will be locked (the DOOR LOCKED symbol

will

be on). During the wash cycle, the name of the phase in

progress will appear on the display. To change a wash

cycle while it is in progress, pause the washer dryer

using the START/PAUSE button (the START/PAUSE

indicator light will flash slowly in an orange colour); then

select the desired cycle and press the START/PAUSE

button again.

To open the door while a cycle is in progress, press the

START/PAUSE button; if the DOOR LOCKED

symbol is switched off the door may be opened. Press

the START/PAUSE button again to restart the wash

cycle from the point at which it was interrupted.

8. THE END OF THE WASH CYCLE.This will be

indicated by the text "END OF CYCLE" on the display;

when the DOOR LOCKED

symbol switches off the

door may be opened. Open the door, unload the laundry

and switch off the machine.

 If you wish to cancel a cycle which has already begun,

press and hold the

button. The cycle will be stopped

and the machine will switch off.

Fabric

type

Load type Max.

load

(kg)

Cupboard

dry

Henger

dry

Iron

dry

Cotton Clothing of different

sizes, Terry towels

5 180 170 160

Synthe-

tics

Sheets, Shirts, Pyjamas,

socks, etc.

3 180 170 160

Wool Knitwear, Pullovers, etc.

1,5 150 140 130

Table of Drying times (guideline values)

Wash cycles and functions

Wash functions

Stain removal

This function is particularly useful for the removal of

stubborn stains.

Place extra compartment 4

(supplied) into

compartment 1. When

pouring in the bleach, be

careful not to exceed the

"max" level marked on the

central pivot (see figure).

To run the bleach cycle on its

own, pour the bleach into

extra compartment 4, set

the "Rinse" programme and

activate the "Stain removal" programme. To bleach during a

wash cycle, pour in the detergent and any fabric softener you

wish to use, set the desired wash cycle and enable the "Stain

removal" function.

 The use of extra compartment 4 excludes the Pre-wash

function.

 It cannot be used with the , , , Pump out and

Drying programmes.

Extra rinse

By selecting this option, the efficiency of the rinse is

increased and optimal detergent removal is guaranteed. It

is particularly useful for sensitive skin.

 It cannot be used in conjunction with the , , Pump

out and Drying programmes.

For all Test Institutes:

* Test wash cycle in compliance with regulation EN 60456: set wash cycle with a temperature of 60°C.

Table of wash cycles

Easy iron

By selecting this function, the wash and spin cycles will be

modified in order to reduce the formation of creases. At

the end of the cycle the washer dryer will perform slow

rotations of the drum; the EASY IRON indicator light will

switch on, the START/PAUSE indicator light will flash in an

orange colour and the text "END OF CYCLE" will appear on

the display. To end the cycle, press the START/PAUSE

button or the EASY IRON button.

For the Silk/Curtains cycle, the machine will end the cycle

while the laundry is soaking; the EASY IRON indicator light

will switch on, the START/PAUSE indicator light will flash in

an orange colour and the text "STOP WITH WATER" will

appear on the display. To drain the water so that the

laundry may be removed, press the START/PAUSE button

or the EASY IRON button.

 It may not be used with the , , , Pump out and

Drying programmes.

Mini load

This function is recommended for when the load of laundry

is equal to half, or less than half, of the maximum

recommended load (see Table of wash cycles).

 It cannot be used with the , , Pump out and Drying

programmes.

MAX

Description of the wash cycle

Max

temp.

(°C)

Max.

speed

(rpm)

Dry

ing

Detergents Max. load (kg)

Cycle

duration

Bleach Wash

Fabric

softener

Normal

Mini

Load

Everyday wash cycles (Daily)

Cottons (*)

press of the button)

extremely soiled whites.

90° 1200

lll l

Cottons

press of the button)

heavily soiled whites and resistant colours.

60° 1200

lll l

Cottons

press of the button)

heavily soiled whites and delicate colours.

40° 1200

lll l

Synthetics

press of the button)

heavily soiled resistant colours.

60° 800

lll l

31,5

Synthetics

press of the button)

lightly soiled resistant colours.

40° 800

lll l

31,5

Mix 30'

press of the button)

to refresh lightly soiled garments quickly

(not suitable for wool, silk and clothes which require washing by hand).

30° 800

3 -

Mix 15'

press of the button)

to refresh lightly soiled garments quickly (not

suitable for wool, silk and clothes which require washing by hand).

30° 800

1,5 -

Silk/Curtains:

for garments in silk and viscose, lingerie.

30° 0 - -

Memory:

allows for any wash cycle to be stored.

Wool:

for wool, cashmere, etc.

40° 800

lll l

1,5 1

Drying programmes

Cotton dry

press of the button)

- -

- - - 5 -

Synthetics dry

press of the button)

- -

- - - 3 -

Wool dry

press of the button)

- -

- - - 1,5 -

Partial wash cycles

Spin - 1200

- - - 7 -

Rinse

press of the button)

- 1200

Pump out

press of the button)

- 0 - - - - 7 -

The duration of the wash cycles can be checked

on the display.

Wash cycles

Detergents and laundry

Detergent dispenser drawer

Good washing results also depend on the correct

dose of detergent: adding too much detergent will not

necessarily result in a more efficient wash, and may in

fact cause build up on the inside of your appliance

and contribute to environmental pollution.

 Do not use hand washing detergents because these

create too much foam.

Open the detergent

dispenser drawer and

pour in the detergent or

washing additive, as

follows.

compartment 1: Pre-wash detergent (powder)

Before pouring in the detergent, make sure that extra

compartment 4 has been removed.

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in immediately

prior to the start of the wash cycle.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

extra compartment 4: Bleach

Preparing the laundry

 Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from

whites

 Empty all garment pockets and check the buttons.

 Do not exceed the listed values, which refer to the

weight of the laundry when dry:

Durable fabrics: max. 7 kg

Synthetic fabrics: max. 3 kg

Delicate fabrics: max. 2 kg

Wool: max. 1.5 kg

Silk: max. 1 kg

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

MAX

Special wash cycles

Mix 30: this wash cycle was designed to wash

lightly soiled garments quickly: it lasts just 30 minutes

and therefore saves both energy and time. By

selecting this wash cycle (

at 30°C), it is possible to

wash different fabrics together (except for wool and

silk items), with a maximum load of 3 kg.

Mix 15: this wash cycle was designed to wash

lightly soiled garments quickly: it lasts just 15 minutes

and therefore saves both energy and time. By

selecting this wash cycle (

at 30°C), it is possible to

wash different fabrics together (except for wool and

silk items), with a maximum load of 1.5 kg.

Silk: use special wash cycle

to wash all silk

garments. We recommend the use of special

detergent which has been designed to wash delicate

clothes.

Curtains: fold curtains and place them in a pillow

case or mesh bag. Use wash cycle

Wool: Scholtès is the only washer dryer

manufacturer to have been awarded the prestigious

Woolmark Platinum Care endorsement (M.0508) by

the Woolmark Company, which means that all

woollen garments may be washed in the washer

dryer, even those which state hand wash only

on the label. Wash cycle therefore offers complete

peace of mind when washing woollen garments in the

washer dryer (max. load 1.5 kg) and guarantees

optimal performance.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

and to distribute the load in a uniform manner, the

drum rotates continuously at a speed which is slightly

greater than the washing rotation speed. If, after

several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the

load is excessively unbalanced, the washer dryer

performs the distribution process instead of spinning.

To encourage improved load distribution and balance,

we recommend small and large garments are mixed

in the load.

Precautions and tips

 This washer dryer was designed and constructed in

accordance with international safety regulations. The

following information is provided for safety reasons

and must therefore be read carefully.

General safety

 This appliance was designed for domestic use only.

 The washer dryer must only be used by adults, in

accordance with the instructions provided in this manual.

 Do not touch the machine when barefoot or with

wet or damp hands or feet.

 Do not pull on the power supply cable when

unplugging the appliance from the electricity

socket. Hold the plug and pull.

 Do not open the detergent dispenser drawer while

the machine is in operation.

 Do not touch the drained water as it may reach

extremely high temperatures.

 Never force the porthole door. This could damage

the safety lock mechanism designed to prevent

accidental opening.

 If the appliance breaks down, do not under any

circumstances access the internal mechanisms in

an attempt to repair it yourself.

 Always keep children well away from the appliance

while it is operating.

 The door can become quite hot during the wash cycle.

 If the appliance has to be moved, work in a group

of two or three people and handle it with the utmost

care. Never try to do this alone, because the

appliance is very heavy.

 Before loading laundry into the washer dryer, make

sure the drum is empty.

 During the drying phase, the door tends to get

quite hot.

 Do not use the appliance to dry clothes that have

been washed with flammable solvents (e.g.

trichlorethylene).

 Do not use the appliance to dry foam rubber or

similar elastomers.

 Make sure that the water tap is turned on during

the drying cycles.

Disposal

 Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

 The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected

separately in order to optimise the recovery and

Opening the porthole door manually

In the event that it is not possible to open the

porthole door due to a powercut, and if you wish to

remove the laundry, proceed as follows:

1. remove the plug from the electrical socket.

2. make sure the water level inside the machine is

lower than the door opening; if it is not, remove

excess water using the drain hose, collecting it in a

bucket.

3. pull outwards using the tab as indicated in the

figure, until the plastic tie-rod is freed from its stop

position; pull downwards and open the door at the

same time.

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out "wheeled bin" symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Care and maintenance

Cutting off the water and electricity

supplies

 Turn off the water tap after every wash cycle. This

will limit wear on the hydraulic system inside the

washer dryer and help to prevent leaks.

 Unplug the washer dryer when cleaning it and

during all maintenance work.

Cleaning the washer dryer

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth soaked

in lukewarm soapy water. Do not use solvents or

abrasives.

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and pulling it

out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of your

appliance

 Always leave the porthole door ajar in order to

prevent unpleasant odours from forming.

Cleaning the pump

The washer dryer is fitted with a self-cleaning pump

which does not require any maintenance.

Sometimes, small items (such as coins or buttons)

may fall into the pre-chamber which protects the

pump, situated in its bottom part.

 Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. unscrew the lid by

rotating it anti-clockwise

(see figure): a little water

may trickle out. This is

perfectly normal;

2. clean the inside thoroughly;

3. screw the lid back on;

Checking the water inlet hose

Check the inlet hose at least once a year. If there are

any cracks, it should be replaced immediately: during

the wash cycles, water pressure is very strong and a

cracked hose could easily split open.

 Never use second-hand hoses.

Troubleshooting

Your washer dryer could fail to work. Before contacting the Technical Assistance Centre (see Assistance), make

sure that the problem cannot be not solved easily using the following list.

Problem:

The washer dryer does not

switch on.

The wash cycle does not start.

The washer dryer does not take

in water (the text "NO WATER,

CHECK SUPPLY" appears

on the display).

The washer dryer continuously

takes in and

drains water.

The washer dryer does not drain

or spin.

The washer dryer vibrates a lot

during the spin cycle.

The washer dryer leaks.

The machine is locked and the

display flashes, indicating an

error code (e.g. F-01, F-..).

There is too much foam.

The washer-dryer does not dry.

Possible causes / Solutions:

 The appliance is not plugged into the socket fully, or is not making contact.

 There is no power in the house.

 The washer dryer door is not closed properly.

 The ON/OFF button has not been pressed.

 The START/PAUSE button has not been pressed.

 The water tap has not been opened.

 A delayed start has been set (see How to run a wash cycle or a drying cycle).

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap has not been opened.

 There is no water supply in the house.

 The pressure is too low.

 The START/PAUSE button has not been pressed.

 The drain hose is not fitted at a height between 65 and 100 cm from

the floor (see Installation).

 The free end of the hose is under water (see Installation).

 The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap,

switch the appliance off and contact the Assistance Service. If the

dwelling is on one of the upper floors of a building, there may be problems

relating to water drainage, causing the washer dryer to fill with water and

drain continuously. Special anti-draining valves are available in shops and

help to avoid this inconvenience.

 The wash cycle does not include draining: some wash cycles require the

drain phase to be started manually (see Wash cycles and functions).

 The EASY IRON function has been activated: To complete the wash

cycle, press the START/PAUSE button (see Wash cycles and functions).

 The drain hose is bent (see Installation).

 The drainage duct is clogged.

 The drum was not unlocked correctly during installation (see Installation).

 The washer dryer is not level (see Installation).

 The washer dryer is trapped between cabinets and walls (see Installation).

 The water inlet hose is not screwed on properly (see Installation).

 The detergent dispenser drawer is blocked (for cleaning instructions, see Care

and maintenance).

 The drain hose is not fixed properly (see Installation).

 Switch off the machine and unplug it, wait for approximately 1 minute

and then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

 The detergent is not suitable for machine washing (it should display the

text for washer dryers or hand and machine wash, or the like).

 Too much detergent was used.

 The appliance is not plugged into the socket, or not enough to make contact.

 There has been a power failure.

 The appliance door is not shut properly.

 A delayed start has been set.

 DRYING is in the OFF position.

Service

Before calling for Assistance:

 Check whether you can solve the problem alone (see Troubleshooting);

 Restart the programme to check whether the problem has been solved;

 If this is not the case, contact an authorised Technical Assistance Centre using the telephone number

provided on the guarantee certificate.

 Always request the assistance of authorised technicians.

Have the following information to hand:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

This information can be found on the data plate applied to the rear of the washer dryer, and can also be

found on the front of the appliance by opening the door.

Français

Sommaire

Installation, 16-17-18-19

Déballage et mise à niveau

Raccordements eau et électricité

Premier cycle de lavage

Caractéristiques techniques

Instructions pour l'installateur

Description du lavante-séchante, 20-21

Bandeau de commandes

Écran

Comment effectuer un cycle de lavage

ou un séchage, 22

Programmes et fonctions, 23

Tableau des programmes

Fonctions de lavage

Produits lessiviels et linge, 24

Tiroir à produits lessiviels

Triage du linge

Programmes spéciaux

Système déquilibrage de la charge

Précautions et conseils, 25

Sécurité générale

Mise au rebut

Ouverture manuelle de la porte hublot

Entretien et soin, 26

Coupure de larrivée deau et du courant

Nettoyage du lavante-séchante

Nettoyage du tiroir à produits lessiviels.

Entretien du hublot et du tambour

Nettoyage de la pompe

Contrôle du tuyau darrivée de leau

Anomalies et remèdes, 27

Assistance, 28

SDLE 129

Mode demploi

LAVANTE-SÉCHANTE

Installation

 Conserver ce mode demploi pour pouvoir le

consulter à tout moment. En cas de vente, de

cession ou de déménagement, veiller à ce quil suive

toujours le lavante-séchante pour que son nouveau

propriétaire soit informé sur son mode de

fonctionnement et puisse profiter des conseils

correspondants.

 Lire attentivement les instructions: elles fournissent

des conseils importants sur linstallation, lutilisation et

la sécurité de lappareil.

Déballage et mise à niveau

Déballage

1. Déballer le lavante-séchante.

2. Contrôler que le lavante-séchante na pas été

endommagé pendant le transport. Sil est abîmé, ne

pas le raccorder et contacter le vendeur.

3. Enlever les 4 vis de

protection servant au

transport, le caoutchouc

et la cale, placés dans la

partie arrière (voir figure).

4. Boucher les trous à laide des bouchons plastique

fournis.

5. Conserver toutes ces pièces: il faudra les remonter

en cas de transport du lavante-séchante.

 Les pièces demballage ne sont pas des jouets pour

enfants.

Mise à niveau

1. Installer le lavante-séchante sur un sol plat et

rigide, sans lappuyer contre des murs, des meubles

ou autre.

2. Si le sol nest pas

parfaitement horizontal,

visser ou dévisser les

pieds de réglage avant

(voir figure) pour niveler

lappareil; son angle

dinclinaison, mesuré sur

le plan de travail, ne doit

pas dépasser 2°.

Une bonne mise à niveau garantit la stabilité de

lappareil et évite quil y ait des vibrations, du bruit et

des déplacements en cours de fonctionnement. Si la

machine est posée sur de la moquette ou un tapis,

régler les pieds de manière à ce quil y ait

suffisamment despace pour assurer une bonne

ventilation.

Raccordements eau et électricité

Raccordement du tuyau darrivée de leau

1. Monter le joint A sur

lextrémité du tuyau

dalimentation et le visser

à un robinet deau froide

à embout fileté 3/4 gaz

(voir figure).

Faire couler leau jusquà

ce quelle soit limpide et

sans impuretés avant de

raccorder.

2. Raccorder le tuyau

darrivée de leau au

lavante-séchante en le

vissant à la prise deau

prévue, dans la partie

arrière en haut à droite

(voir figure).

3. Attention à ce que le tuyau ne soit pas plié ou

écrasé.

 La pression de leau doit être comprise entre les

valeurs indiquées dans le tableau des Caractéristiques

techniques (voir page ci-contre).

 Si la longueur du tuyau dalimentation ne suffit pas,

sadresser à un magasin spécialisé ou à un technicien

agréé.

 Nutiliser que des tuyaux neufs.

 Utiliser ceux qui sont fournis avec lappareil.

65 - 100 cm

Raccordement du tuyau de vidange

Raccorder le tuyau

dévacuation, sans le

plier, à un conduit

dévacuation ou à une

évacuation murale placés

à une distance du sol

comprise entre 65 et 100

cm;

ou bien laccrocher à un

évier ou à une baignoire,

dans ce cas, fixer le

support en plastique

fourni avec lappareil au

robinet (voir figure).

Lextrémité libre du tuyau

dévacuation ne doit pas

être plongée dans leau.

 Lutilisation dun tuyau de rallonge est absolument

déconseillée mais si on ne peut faire autrement, il faut

absolument quil ait le même diamètre que le tuyau

original et sa longueur ne doit pas dépasser 150 cm.

Branchement électrique

Avant de brancher la fiche dans la prise de courant,

sassurer que:

 la prise est bien reliée à la terre et est conforme aux

réglementations en vigueur;

 la prise est bien apte à supporter la puissance

maximale de lappareil indiquée dans le tableau des

Caractéristiques techniques (voir ci-contre);

 la tension dalimentation est bien comprise entre les

valeurs figurant dans le tableau des Caractéristiques

techniques (voir ci-contre);

 la prise est bien compatible avec la fiche du lavan-

te-séchante. Autrement, remplacer la prise ou la

fiche.

 Le lavante-séchante ne doit pas être installé dehors,

même à labri, car il est très dangereux de le laisser

exposé à la pluie et aux orages.

 Après installation du lavante-séchante, la prise de

courant doit être facilement accessible.

 Nutiliser ni rallonges ni prises multiples.

 Le câble ne doit être ni plié ni trop écrasé.

 Le câble dalimentation ne doit être remplacé que

par des techniciens agréés.

Attention! Nous déclinons toute responsabilité en cas

de non-respect des normes énumérées ci-dessus.

Premier cycle de lavage

Avant la première mise en service de lappareil,

effectuer un cycle de lavage avec un produit lessiviel

mais sans linge et sélectionner le programme

Caractéristiques techniques

Modèle

SDLE 129

Dimensions

largeur 59,5 cm

hauteur 81,5 cm

profondeur 54,5 cm

Capacité

de 1 à 7 kg pour le lavage

de 1 à 5 kg pour le séchage

Raccordements

électriques

Voir la plaque signalétique appliquée

sur la machine

Raccordements

hydrauliques

pression maximale 1 MPa (10 bar)

pression minimale 0,05 MPa (0,5 bar)

capacité du tambour 52 litres

Vitesse

d'essorage

jusqu'à 1200 tours minute

Programmes de

contrôle selon la

norme EN 50229

lavage: programme

(1° pression de

la touche)

; température 60°C;

effectué avec une charge de 7 kg.

séchage: premier séchage effectué

avec 2 kg de charge en sélectionnant

le niveau de séchage "A REPASSER";

deuxième séchage effectué avec 5 kg

de charge en sélectionnant le niveau

de séchage "A RANGER".

Cet appareil est conforme aux

Directives Communautaires suivantes:

- 89/336/CEE du 03/05/89

(Compatibilité électromagnétique) et

modifications suivantes

- 2002/96/CE

- 2006/95/CE (Basse Tension)

Instructions pour l'installateur

Application du panneau d'habillage en bois sur

la porte et montage du machine à laver à

l'intérieur des éléments:

Au cas où, après le montage du panneau en bois, il faudrait

expédier la machine pour son installation finale, nous vous

conseillons de la laisser dans son emballage d'origine.

L'emballage a été justement réalisé de manière à permettre

le montage du panneau en bois sur la machine sans

déballer complètement le produit (voir figures ci-dessous).

Le panneau en bois couvrant la façade ne doit pas avoir

plus de 18 mm d'épaisseur, il peut être articulé tant à

droite qu'à gauche. Pour plus de facilité d'emploi, nous

conseillons d'adopter le même sens d'ouverture que pour

le hublot dont les charnières sont montées sur le côté

gauche.

Tur seite

Accessoires montage porte (Fig.1-2-3-4-5).

Fig. 1

N°2 Charnière

N°1 Aimant N°1 Butoir aimant

N°1 Cheville en

caoutchouc

N°2 Supports charnière

N°4 Cales

Fig. 2

Fig. 3 Fig. 4

Fig. 5

Fig. 4/B

- 6 vis autotaraudeuses l = 13 mm "type A".

- 2 vis métriques à tête évasée l = 25 mm "type B"; pour

fixation du butoir aimant au meuble.

- 4 vis métriques l = 15 mm "type C"; pour montage des

supports charnière au meuble.

- 4 vis métriques l = 7 mm "type D"; pour montage des

charnières aux supports.

Montage des pièces sur la façade de la machine.

- Montez les supports de la charnière sur la façade, en

positionnant le trou indiqué par une flèche dans la fig. 1

vers lintérieur de la façade et interposez une cale (fig. 4/B).

Utilisez les vis type C.

- Montez le butoir aimant du côté opposé en haut et

interposez deux cales (fig. 4/B). Utilisez les deux vis type B.

Utilisation du gabarit de forage.

- Pour marquer l'emplacement des trous sur le côté du

panneau, alignez le gabarit de perçage avec le côté

supérieur gauche du panneau en vous servant des lignes

tracées aux extrémités.

- Pour marquer l'emplacement des trous sur le côté droit

du panneau, alignez le gabarit de perçage avec le côté

supérieur droit du panneau.

- Réalisez à l'aide d'une fraise appropriée les quatre

emplace-ments où devront trouver place les deux

charnières, la cheville en caoutchouc et l'aimant.

Montage des pièces sur le panneau en bois (Porte).

- Montez les charnières aux emplacements prévus (la

partie mobile de la charnière doit se trouver vers l'extérieur

du panneau) et fixez-les à l'aide de 4 vis type A.

- Montez l'aimant à son emplacement en haut, à l'opposé

des charnières et fixez-le au moyen de deux vis type B.

- Montez la cheville en caoutchouc à sa place en bas.

Le panneau est à présent prêt, vous pouvez le monter sur

la machine.

Montage du panneau sur la machine.

Introduisez l'ergot de la charnière indiqué par la flèche fig. 2

dans le logement du support charnière, poussez le panneau

vers la façade de la machine et fixez les deux charnières à

l'aide des deux vis type D.

Fixation du support de la base.

Si la machine est installée à une extrémité de la cuisine

intégrée, montez une ou les deux glissières du socle

comme illustré fig. 8 en réglant leur profondeur en

fonction de la position du socle et, au besoin, fixez-le à

ces dernières fig. 9. Pour monter le support de la base,

procédez comme suit (fig. 8): Fixez l'équerre P à l'aide de

la vis R, insérez le support de la base Q dans la fente

prévue et après l'avoir dûment positionné bloquez-le à

l'aide de l'équerre d'assemblage P et de la vis R.

Montage de la machine à l'intérieur des éléments.

- Poussez la machine à travers l'ouverture en l'alignant

aux autres meubles (fig. 6).

- Servez-vous des pieds de réglage pour amener la

machine à la hauteur désirée.

- Pour régler la position du panneau en bois à la verticale et à

l'horizontale, servez-vous des vis C et D comme illustré fig. 7.

Important: fermez la partie inférieure de la façade, la base

touchant au sol.

Fig. 8 Fig. 9

Accessoires fournis pour le réglage de la hauteur.

Vous trouverez à l'intérieur du couvercle en polystyrène (fig. 10):

2 traverses (G); 1 listel (M);

et à l'intérieur du tambour :

4 pieds supplémentaires (H),

4 vis (I),

4 vis (R),

4 écrous (L),

2 supports pour la base (Q)

Réglage de la machine en hauteur.

La machine peut être réglée en hauteur (de 815 mm à 835

mm) à l'aide de ses 4 pieds.

Si vous souhaitez l'amener à une hauteur supérieure à celle

qui est indiquée plus haut, c'est à dire jusqu'à 870 mm,

utilisez les accessoires suivants :

les 2 traverses (G); les 4 pieds (H); les 4 vis (I); les 4 écrous

(L) puis procédez comme suit (fig. 11):

démontez les 4 pieds originaux, positionnez une traverse G

dans la partie avant de la machine, fixez-la à l'aide des vis I

(en les vissant dans les trous où étaient fixés les pieds

originaux) puis montez les nouveaux pieds H.

Procédez de même dans la partie arrière de la machine.

Vous pouvez alors régler les pieds H pour élever ou abaisser

la machine de 835 mm à 870 mm.

Après avoir atteint la hauteur désirée, bloquez les écrous L à

la traverse G.

Pour régler la machine à une hauteur comprise entre 870

mm et 900 mm, montez le listel M et réglez les pieds H

jusqu'à la hauteur souhaitée.

Pour monter le listel, procédez comme suit:

desserrez les trois vis N situées dans la partie avant du couvercle,

montez le listel M comme illustré fig. 12 et serrez les vis N.

570

min

815

540

595

820 ÷ 900

600 min

Fig. 6 Fig. 7

Fig. 11 Fig. 12

Fig. 10

Tiroir à produits lessiviels: pour charger les

produits lessiviels et les additifs (voir Produits lessiviels

et linge).

Tasto MARCHE/ARRÊT

: appuyer brièvement sur la

touche pour allumer ou éteindre l'appareil. Le voyant

vert MISE EN MARCHE/PAUSE clignotant lentement

indique que la machine est allumée. Pour éteindre le

lavante-séchante en cours de lavage, appuyer sur la

touche pendant au moins 2 secondes de suite ; une

pression brève ou accidentelle n'entraîne pas l'arrêt de

l'appareil. L'arrêt de l'appareil pendant un lavage

annule le lavage en cours.

Touches SÉLECTEUR PROGRAMMES: pour

sélectionner le programme désiré (voir "Tableau des

programmes").

Touche MEMO: maintenir la touche enfoncée pour

mémoriser un cycle et les personnalisations préférées.

Pour retourner à un cycle précédemment mémorisé,

appuyer sur la touche MEMO.

Touches FONCTION: appuyer sur la touche pour

sélectionner la fonction désirée. Le voyant

correspondant s'affiche à l'écran.

Touche ESSORAGE

: appuyer sur cette touche

pour diminuer la vitesse de l'essorage ou pour le

supprimer complètement - la valeur correspondante

s'affiche à l'écran.

Touche TEMPERATURE

: appuyer pour diminuer

la température: la valeur correspondante est affichée

à l'écran.

Touche VERROUILLAGE TOUCHES

: pour

activer le verrouillage des commandes, garder la

touche enfoncée pendant environ 2 secondes. Le

symbole

allumé indique que le bandeau de

commandes est verrouillé. Ceci permet d'éviter toute

modification involontaire des programmes, surtout s'il

y a des enfants à la maison. Pour désactiver le

verrouillage des commandes, garder la touche

enfoncée pendant environ 2 secondes.

Touche DÉPART DIFFÉRÉ

: appuyer sur cette

touche pour sélectionner un départ différé pour le

programme choisi. Le retard est affiché à l'écran.

Touche SÉCHAGE

: appuyer pour sélectionner un

cycle de séchage.

Touche avec voyant MISE EN MARCHE/PAUSE:

quand le voyant vert clignote lentement, appuyer sur

la touche pour démarrer un lavage. Une fois le cycle

lancé, le voyant passe à l'allumage fixe. Pour activer

une pause de lavage, appuyer à nouveau sur la

touche ; le voyant passe à l'orange et se met à

clignoter. Si le symbole

n'est pas allumé, il est

possible d'ouvrir le hublot. Pour faire redémarrer le

lavage exactement à l'endroit de l'arrêt, appuyer une

nouvelle fois sur la touche.

Description du lavante-séchante

Bandeau de commandes

Touche avec

voyant

MISE

EN MARCHE/

PAUSE

Touche

TEMPÉRATURE

Touches

SÉLECTEUR

PROGRAMMES

Tiroir à produits lessiviels

Touches

FONCTION

Touche

MARCHE/ARRÊT

Touche

ESSORAGE

Touche

SÉCHAGE

Écran

Touche

DÉPART

DIFFÉRÉ

Touche

MEMO

Touche

VERROUILLAGE

TOUCHES

La page charge ...

Indesit SDLE 129 (EU) Le manuel du propriétaire

Marque: Indesit

Modèle: SDLE 129 (EU)

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Ce manuel convient également à

sdle 129 eu full

Télécharger le PDF

rapport

dans d''autres langues

English: Indesit SDLE 129 (EU) Owner's manual
español: Indesit SDLE 129 (EU) El manual del propietario

Indesit SDLE 129 (EU) Le manuel du propriétaire

Ce manuel convient également à

Indesit SDLE 129 (EU) Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents