JennAir JUIFX15HX Guide d'installation

INTRODUCTION

INTRODUCTION | 1

W11320441A



BUILT-IN UNDERCOUNTER ICE MAKER

’

MACHINE À GLAÇONS ENCASTRÉE SOUS LE COMPTOIR

INTRODUCTION

INTRODUCTION | 3

SAFETY

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

DANGER

WARNING

You can be killed or seriously injured if you don't immediately follow instructions.

You can be killed or seriously injured if you don't follow instructions.

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

To reduce the risk of re, electric shock, or injury when using your refrigerator, follow these basic precautions:

SAVE THESE INSTRUCTIONS

■

Plug into a grounded 3 prong outlet.

■ Do not remove ground prong.

■ Do not use an adapter.

■ Do not use an extension cord.

■ Do not store explosive substances such as

aerosol cans with a flammable propellant in

this appliance.

■ Disconnect power before cleaning.

■ Disconnect power before servicing.

■ Replace all parts and panels before operating.

■ Connect to potable water supply only.

■ If the supply cord is damaged, it must be replaced

by the manufacturer, its service agent, or similarly

qualified person in order to avoid a hazard.

■ This appliance is not intended for use by persons

(including children) with reduced physical, sensory,

or mental capabilities, or lack of experience and

knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

■ Use two or more people to move and install

ice maker.

■

Children should be supervised to ensure that they do

not play with the appliance.

■ This appliance is intended to be used in household

and similar applications such as:

– staff kitchen areas in shops, offices, and other

working environments;

– farmhouses and by clients in hotels, motels, and

other residential-type environments;

– bed and breakfast-type environments;

– catering and similar non-retail applications.

INTRODUCTION

4 | INTRODUCTION

REGISTERING YOUR

APPLIANCE

Gain access to our concierge-level customer

support by registering your appliance. We make

product registration simple and straightforward

so that you can start using your exclusive

JennAir beneﬁts today.

Registering your appliance allows you to:

■ Streamline your warranty service

If we have your product information, we

can help you faster.

■ Protect your purchase

In case of an insurance loss̶ such as ﬁre,

ﬂood, or theft̶ your product registration

could serve as a proof of purchase.

■ Keep your family safe

We’ll notify you in the rare case of a safety

notiﬁcation.

Start taking advantage of these beneﬁts today

by going online to register your product at

jennair.com/customer-care.

TABLE OF CONTENTS

PRODUCT IDENTIFICATION

Your product identiﬁcation, which includes

the model and serial number, is listed on the

product rating plate.

Recording this information below allows us to

more easily assist you if your product should

ever require service from one of our Whirlpool

Authorized Service Providers.

Model Number: _______________________________

Serial Number: ________________________________

Date of Installation: ___________________________

Authorized Dealer: ___________________________

Authorized Dealer Phone #: __________________

INTRODUCTION

Safety .............................................................................. 3

Registering Your Appliance ............................ 4

Product Identiﬁcation ........................................ 4

GETTING STARTED

Before installation .................................................. 5

Tools Required .......................................................... 5

Parts Provided .......................................................... 5

Vacation or Extended Time

Without Use ............................................................... 6

Unpack the Ice Maker ......................................... 6

Optional Personalizations ................................ 6

SITE PREPARATION

Product and

Opening Dimensions .......................................... 7

Location Requirements ..................................... 8

Electrical Requirements .................................... 9

Water Supply Requirements .......................... 10

Drain Supply Requirements ........................... 11

Gravity Drain System ........................................... 11

Drain Pump System ............................................. 11

DOOR REVERSAL

Removing Hinge Covers .................................... 12

Removing the Hinges ......................................... 14

Preparing the Bottom Hinges....................... 18

Reversing the Hinges .......................................... 20

INSTALLATION

Installing the Drain Pump -

Site Preparation ....................................................... 22

If Ice Maker is Currently Installed ............... 22

Installing the Drain Pump

and Drain Hose ........................................................ 24

Connecting the Water supply ....................... 28

Leveling and Securing ........................................ 30

Custom Wood Door Panel ............................... 34

Connecting the Drain ......................................... 36

Installing Auxiliary Grill ....................................... 38

APPENDIX

Accessories ................................................................. 40

TABLE DES MATIÈRES............44

GETTING STARTED | 5

GETTING STARTED

BEFORE INSTALLATION

Gather the required tools and parts before

starting installation. Read and follow the

instructions provided with any tools listed.

IMPORTANT: These instructions are intended

as a general guide only and do not supersede

any national or local codes in any way.

Compliance with all local, state, or national

codes pertaining to this type of installation

should be determined prior to installation.

Installer: Please be sure to leave Installation

Instructions with the homeowner.

Homeowner: Keep the Installation Instructions

for future reference.

TOOLS REQUIRED

Gather the required tools before starting

installation.

TOOLS REQUIRED

 Drill and drill bits

 Phillips screwdriver

 Pencil

 Masking tape

 Two adjustable wrenches

 Level

 Wood screws

 2" Hole saw or 2" Forstner bit

 3/16" hex driver

 1/4" nut driver

 Pliers

 Right angle drivers

 TORX T20, T25

†

screwdriver

 Tape measure

PARTS PROVIDED

 Cabinet brackets

 Drain hose and clamp (in hose bag) - on

some models only

 #8 x 1/2" pan head wood screws (14)

 Double sided adhesive tape

(for custom door panel)

 Auxiliary grill kit

†

Torx, T20 and T25 are trademarks of Acument Intellectual Properties, LLC.

GETTING STARTED

6 | GETTING STARTED

UNPACK THE ICE MAKER

REMOVING PACKAGING MATERIALS

Uncrate the ice maker. Remove tape and glue

from your ice maker before using.

 To remove any remaining tape or glue

from the exterior of the ice maker,

rub the area briskly with your thumb.

Tape or glue residue can also be easily

removed by rubbing a small amount of

liquid dish soap over the adhesive with

your ﬁngers. Wipe with warm water

and dry.

 Do not use sharp instruments, rubbing

alcohol, ﬂammable ﬂuids, or abrasive

cleaners to remove tape or glue. Do not

use chlorine bleach on the stainless

steel surfaces of the ice maker. These

products can damage the surface of

your ice maker.

CLEANING BEFORE USE

After you remove all of the packaging materials,

clean the inside of your ice maker before using

it. For instructions on how to clean the ice

maker, refer to the cleaning instructions in the

“Ice Maker Care” section of Use and Care Guide.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

ice maker.

Failure to do so can result in back or other

injury.

VACATION OR EXTENDED

TIME WITHOUT USE

When you will not be using the ice maker for

an extended period of time, turn off the water

and power supply to the ice maker.

Check that the water supply lines are insulated

against freezing conditions. Ice formations in

the supply lines can increase water pressure

and cause damage to your ice maker or home.

Damage from freezing is not covered by the

warranty.

OPTIONAL PERSONALIZATIONS

REVERSING THE DOOR

For instructions on how to reverse the door,

refer to the “Door Reversal” section.

CUSTOM PANEL INSTALLATION

For instructions on how to install a custom door

panel, refer to the “Custom Wood Door Panel”

section.

If you plan to install a custom overlay panel, you

will need to make the panel yourself or consult

a qualiﬁed cabinetmaker or carpenter.

IMPORTANT:

 The thickness of the overlay panel must

be 3/4" (1.91 cm).

 Overlay panel must not weigh more

than 8 lbs (3.62 kg).

 Overlay panels weighing more than

recommended may cause damage to

your ice maker.

 Countersink all the handle mounting

hardware.

 Match wood grain direction with that of

adjacent cabinets.

 Sand panel edges to provide a smooth

ﬁnish.

 Use moisture sealer on both sides and

all edges of the panel to avoid damage

from moisture.

PARTS NEEDED:

 Instructions, #8 x 1/2" pan head wood

screws (14)

 Handle Kit (optional)

STAINLESS STEEL PANEL INSTALLATION

For instructions on how to install the Stainless

Steel Panel, refer to the instructions received

with the Stainless Steel Panel kit.

SITE PREPARATION | 7

SITE PREPARATION

PRODUCT AND

OPENING DIMENSIONS

Product Dimensions

Product width A 14

7

⁄

8

" (37.8 cm)

Product height B 33

3

⁄

4

" (85.7 cm)

Product depth

(no door)

C 22

1

⁄

16

" (56.1 cm)

Opening Dimensions

Opening width D 15" (38.1 cm)

Opening height E

34" min (86.4 cm)

34

1

⁄

2

" max (87.6 cm)

Opening depth F 24" (60.96 cm)

D

E

F

A

B

C

SITE PREPARATION

7 | SITE PREPARATION

8 | SITE PREPARATION

SITE PREPARATION

C

D

A

B

SITE PREPARATION

LOCATION REQUIREMENTS

Installation must comply with all governing

codes and ordinances.

TEMPERATURE

It is recommended that you install the

ice maker in a well-ventilated area with

temperatures above 55°F (13°C) and below 110°F

(43°C). Best results are obtained between 70°F

and 90°F (21ºC and 32°C).

LOCATION

The ice maker must be installed in an area

sheltered from the elements, such as wind, rain,

or water spray.

To ensure proper ventilation for your ice

maker, the front side must be completely

unobstructed. The ice maker may be closed

in on the top and three sides, however the

installation should allow the ice maker to be

pulled forward for servicing if necessary.

The auxiliary grill kit provided can be used to

align the toe grill with the rest of the cabinets

while not obstructing ventilation of the ice

maker.

Floor must be able to support the ice maker’s

total weight, of more than 106 lbs (48.08 kg),

including door panels and contents of the

ice maker. It is important for the ice maker to

be level in order to work properly. If needed,

you can adjust the height of the ice maker by

changing the height of the leveling legs.

Check that the power supply cord, water supply

line, and drain line (on some models) are not

damaged, pinched, or kinked between the ice

maker and the cabinet.

Required zone for utility

hole/slot cutout location

7⁄" (19.05 cm) 7⁄" (19.05 cm)

SITE PREPARATION | 9

SITE PREPARATION

IMPORTANT:

■ This ice maker has been designed for ﬂush

install in instances where the power supply,

water supply, and drain are located in a

cabinetry.

■ For installation of product with utilities

behind the ice maker, ﬂush install may not

be achieved.

■ Refer “Location Requirement” illustration

and table below for utility slot/hole cutout

location.

Utility Slot/Cutout Location Zone

Dimension

A 9" (22.9 cm)

B 8" (20.3 cm)

C 7" (17.8 cm)

Diameter of the hole D 2" (5 cm)

ELECTRICAL REQUIREMENTS

Electrical Requirements

Power Supply 115 V, 60Hz, AC only

Circuit Breaker 15 to 20 A, fused

Receptacle 3 prong grounding-type

Outlet Non-GFCI

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result

in death, fire, or electrical shock.

WARNING

IMPORTANT:

■ Use an outlet that cannot be turned off by a

switch. Do not use an extension cord.

■ It is recommended that this product not be

connected to a GFCI (Ground Fault Circuit

Interrupter) protected outlet, as nuisance

tripping of the power supply may occur.

■ The ice maker must be grounded. The

ice maker is equipped with a power

supply cord having a grounded 3 prong

plug. The cord must be plugged into a

mating, grounded, 3 prong wall receptacle,

grounded in accordance with the National

Electrical Code and local codes and

ordinances. If a mating wall receptacle is

not available, it is the personal responsibility

of the customer to have a properly

grounded 3 prong wall receptacle installed

by a qualiﬁed electrician.

10 | SITE PREPARATION

SITE PREPARATION

IMPORTANT:

■ Connect to potable water supply only.

■ A reverse osmosis water ﬁltration system is

not recommended for ice makers that have

a drain pump installed. Reverse osmosis

water ﬁltration systems should be used for

gravity drain systems only.

■ Connect the ice maker drain to your drain

in accordance with the International

Plumbing Code and any local codes and

ordinance.

■ To achieve a ﬂush installation, the water

shutoff valve should not be installed in the

wall behind the refrigerator, but in another

easily accessible location.

■ The drain pump discharge line must

terminate at an open-site drain.

■ Maximum rise 10 ft (3.1 m)

■ Maximum run 100 ft (30.5 m)

NOTE: If the drain hose becomes twisted and

water cannot drain, your ice maker will not

work.

WATER SUPPLY REQUIREMENTS

Before connecting the ice maker, ensure that

the water supply lines are insulated against

freezing conditions. Ice formations in the

supply lines can increase water pressure and

damage the ice maker or home. Damage

from frozen supply lines is not covered by the

warranty.

Use new hoses supplied with the product. Do

not reuse old hoses.

Water Supply Requirements

Water Pressure 30-120 psi (207-827 kPa)

Excess Water Line

for Connection

30" (76.2 cm)

Water Inlet Supply

1/4” (6.35 mm) OD soft

copper tubing

Drain Pump With shut-off valve

REVERSE OSMOSIS WATER SUPPLY

A reverse osmosis system may be used if the

water pressure from the ﬁltration system meets

the required water pressure requirements.

If a reverse osmosis system is desired, only a

whole-house capacity reverse osmosis system,

capable of maintaining the steady water supply

required by the ice maker, is recommended.

Faucet capacity reverse osmosis systems are

not able to maintain the steady water supply

required by the ice maker.

SITE PREPARATION | 11

SITE PREPARATION

DRAIN SUPPLY REQUIREMENTS

Connect the ice maker drain to your drain in

accordance with all state and local codes and

ordinances. Follow these guidelines when

installing drain lines. This will help avoid water

from ﬂowing back into the ice maker storage

bin. Water ﬂowing back into the ice maker can

potentially ﬂow onto the ﬂoor and cause water

damage.

Drain Requirements

Inside

Diame-

ter

minimum 5/8" (15.88 mm)

Drain

Lines

Drain lines must have a

1" drop per 48" of run

(2.54 cm drop per 122 cm of run) or

1/4" drop per 12" of run

(6.35 mm drop per 30.48 cm of run)

Do not connect the outlet end of the drain tube

to a closed pipe system to avoid drain water

from backing up into the ice maker.

GRAVITY DRAIN SYSTEM

The ideal installation has a standpipe with a

1½" (3.81 cm) to 2" (5.08 cm) PVC drain reducer

installed directly below the outlet of the drain

tube as shown. You must maintain a 1" (2.54

cm) air gap between the drain hose and the

standpipe.

DRAIN PUMP SYSTEM

Drain pump maximum capability: For every

1 ft (0.31 m) of rise, subtract 10 ft (3.1 m) of

maximum allowable run.

IMPORTANT: A drain pump is necessary when

a ﬂoor drain is not available. A Drain Pump kit,

Part Number 1901A, is available for purchase at

jennair.com/accessories/details/1901A.

NOTE: It may be desirable to insulate the

drain line thoroughly up to the drain inlet. An

Insulation Sleeve kit, Part Number W10365792,

is available for purchase at

jennair.com/accessories/details/W10365792.

Drain pump modelGravity drain model

Gravity Drain System Dimensions

Drain Hose A

Air Gap B 1" (2.54 cm)

PVC Drain Reducer C

2" to 1

1

⁄

2

"

(5 cm - 3.8 cm)

Center of Drain D

23" (58.4 cm) from

front of door, with

or without 3/4"

(1.9 cm) panel on

the door, centered

left to right (7

5

⁄

16

"

[18.56 cm]) from

either side of the

ice maker.

Bottom of Ice

Maker to top of PVC

Drain Reducer

E 1

7

⁄

8

" (4.8 cm)

Depth to center of

PVC Drain Reducer

F 23" (58.4 cm)

E

A

B

C

D

F

DOOR REVERSAL

12 | DOOR REVERSAL

REMOVING HINGE COVERS

If door reversal is not needed, skip “Door Reversal” section.

!

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or

electrical shock.

1

Unplug the ice maker or disconnect

power.

DOOR REVERSAL

DOOR REVERSAL | 13

2

Remove the screws attaching top and

bottom hinge covers using an 3/16" hex

driver.

Crush Hazard

Articulated hinges are self closing and many

pinch points exist prior to cabinet

installation.

Do not remove hinge covers until product is

ready to be installed.

Failure to follow these instructions can result

in crush, cut, or pinch injuries.

WARNING

Hinge cover

3

Using pliers, remove the hinge covers

from the top and bottom hinges.

NOTE: Save the hinge covers for

future use. Reinstall the hinge covers

if product is removed from cabinet

installation.

DOOR REVERSAL

14 | DOOR REVERSAL

REMOVING THE HINGES

1

Lay down the ice maker as shown in

the illustration. Be sure to cover the

ﬂoor with cardboard or hardboard to

avoid damaging it.

WARNING

Excessive Weight Hazard

Use two or more people to move and install

ice maker.

Failure to do so can result in back or other

injury.

DOOR REVERSAL

DOOR REVERSAL | 15

2

Remove the screws and the top metal

bracket using the Phillips screwdriver.

Place them aside.

3

Remove the screw from the top and

bottom end caps using the Phillips

screwdriver. Remove and place them

aside.

4

Using Torx T25 screwdriver unscrew

the door hinge screws completely

from the top and bottom hinges and

place them aside.

DOOR REVERSAL

16 | DOOR REVERSAL

REMOVING THE HINGES CONT.

6

Remove the plastic screw cover from

the inside of the hinges and place

them aside.

5

Remove the door and place it aside.

Swap the hinge screws to the opposite

side.

DOOR REVERSAL

DOOR REVERSAL | 17

9

Swap the magnetic door catch to other

side.

8

Remove the screw cap cover and

replace on the other side.

7

Remove the screws and hinges

from the cabinet with the Torx T25

screwdriver and place them aside.

Crush Hazard

Articulated hinges are self closing and many

pinch points exist prior to cabinet

installation.

Do not operate, or close, the hinges while

they are removed from the ice maker.

Failure to follow these instructions can

result in crush, cut, or pinch injuries.

WARNING

DOOR REVERSAL

18 | DOOR REVERSAL

1

Unscrew and remove the grill cover

using a TORX T20 screwdriver. Place

them aside.

PREPARING THE BOTTOM HINGES

Grill cover screws

2

Remove the screw cover and place

it on the other side as shown in the

illustration.

DOOR REVERSAL

DOOR REVERSAL | 19

3

Reinstall the grill cover.

DOOR REVERSAL

20 | DOOR REVERSAL

REVERSING THE HINGES

3

Take the original bottom hinge, ﬂip it

and place it in the top hinge position

on the opposite side. Slide onto the

cabinet hinge screws.

2

Take the original top hinge, ﬂip it

and place it in the bottom hinge

position on the opposite side. Slide

onto the cabinet hinge screws. The

hinge tabs on the hinges should

always face towards each other.

1

Install the hinge screws (placed aside

in step 7 of “Preparing the Bottom

Hinges”) half way on the desired side of

the cabinet.

4

Fully tighten the top and bottom hinge

screws.

Hinge tab

La page charge ...

JennAir JUIFX15HX Guide d'installation

Ce manuel convient également à

JennAir JUIFX15HX Guide d'installation

dans d''autres langues

Documents connexes

Autres documents