Yamaha EMX7 spécification

Catégorie
Mélangeurs audio
Taper
spécification

Ce manuel convient également à

1
General Specifications
0 dBu = 0.775 Vrms, Output impedance of signal generator (Rs) = 150 Ω
All level controls are at their maximum position if not specified.
*1 THD+N is measured with 22 kHz LPF
*2 Noise is measured with A-weighting filter.
*3 Crosstalk is measured with 1 kHz band pass filter.
The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download
the manual file.
Output Power
1 kHz THD+N < 10%
(CEA2006)
710 W + 710 W (4 Ω)
500 W + 500 W (8 Ω)
1 kHz THD+N < 1%
(CEA2006)
600 W + 600 W (4 Ω)
400 W + 400 W (8 Ω)
Input to SPEAKERS
Input to STEREO OUT, AUX1 SEND, AUX2 SEND
Frequency Response
Refer to the nominal
output level @ 1 kHz
+1 dB/-3 dB (40 Hz to 20 kHz) +0.5 dB/-1 dB (20 Hz to 20 kHz)
Total Harmonic
Distortion
*1
(THD+N)
MIC/LINE =
LINE (CH1–4)
0.1% @ 10 W (40 Hz to 20 kHz)
0.04% @ 65 W (1 kHz)
0.02% @ +14 dBu (20 Hz to 20 kHz)
0.007% @ +20 dBu (1 kHz)
Hum & Noise
*2
(20 Hz to 20 kHz)
Equivalent Input Noise -117 dBu
Residual Output Noise
-70 dBu (40 Hz to 20 kHz, STEREO MASTER
LEVEL: min)
-82 dBu (20 Hz to 20 kHz, STEREO MASTER
LEVEL: min)
Crosstalk (1 kHz)
*3
-85 dB
Input channels TOTAL: 12 channels Mono (MIC/LINE): 8, Stereo (LINE): 4
Output channels SPEAKERS [A, B], AUX1 SEND, AUX2 SEND, STEREO OUT [L, R], REC OUT [L, R]
Bus Stereo: 1, AUX: 2 (Including FX)
Input Channel
Function
MIC/LINE (CH1–4) 30 dB PAD
Hi-Z (CH4) Supported
HPF (CH1–3) 80 Hz, -12 dB/oct.
Equalizer (EQ)
HIGH: 10 kHz +15 dB / -15 dB (Shelving)
MID: 2.5 kHz +15 dB / -15 dB (Peaking)
LOW: 100 Hz +15 dB / -15 dB (Shelving)
COMP (CH1–4) 1-knob COMP
Level Meter 2 × 12 points LED meter (-30, -25, -20, -15, -10, -6, -3, 0, +3, +6, +10, PEAK)
Built-in Effect SPX Algorithm 24 programs
Output Channel Function Feedback suppressor, Graphic equalizer, Speaker processor
Phantom Power Voltage +48 V
FOOT SW Effect mute on/off
Protection
Load Protection: DC-fault
Amplifier Protection: Over heat protection, Over current protection, Integral power protection
Power Supply Protection: Over heat protection, Over current protection
Power Requirements AC 100-240 V, 50 Hz/60 Hz
Power Consumption 45 W (Idle) / 250 W (1/8 Power)
Dimensions (W × H × D) 465 mm × 308 mm × 325 mm (18.3" × 12.1" × 12.8")
Net Weight 9.5 kg (20.9 lb)
Included Accessory AC Power Cord (2.5 m), Owners Manual, Technical Specifications
Optional Accessory Rack-mount brackets: RK-EMX7, Foot switch: FC5
Operating Temperature 0 to +40°C
Analog Input Characteristics
0 dBu = 0.775 Vrms
*1 Sensitivity is the lowest level that will produce an output of +4 dBu (1.228 V) or the nominal output level when the unit is set to maximum gain.
(All level controls are at their maximum position.)
*2 Level controls setting : Channel level controls are at their t position. Master level controls are at their maximum position.
*3 1&Sleeve = GND, 2&Tip = HOT, 3&Ring = COLD
*4 Tip = Signal, Sleeve = GND
*5 1 = GND, 2 = HOT, 3 = COLD
*6 Tip = LEFT, Ring = RIGHT, Sleeve = GND
Analog Output Characteristics
0 dBu = 0.775 Vrms
0 dBV = 1.00 Vrms
*1 Tip = HOT, Ring = COLD, Sleeve = GND
Speaker Output Characteristics
*1 1+ = Positive, 1- = Negative
*2 Tip = Positive, Sleeve = Negative
Input Jack MIC/LINE Hi-Z
Actual Load
Impedance
For Use
with
Nominal
Input Level
Connector
Sensitivity
*1
Nominal Level
(t Position)
*2
Max.
Before Clip
CH 1–4
XLR
MIC
3 kΩ
50–600 Ω
Mics
-60 dBu
(0.775 mV)
-43 dBu
(5.48 mV)
-15 dBu
(138 mV)
Combo jack
*3
(Balanced)
LINE
-30 dBu
(24.5 mV)
-13 dBu
(173 mV)
+15 dBu
(4.36 V)
Phone
MIC
8 kΩ
600 Ω
Lines
-50 dBu
(2.45 mV)
-33 dBu
(17.3 mV)
-5 dBu
(436 mV)
LINE
-20 dBu
(77.5 mV)
-3 dBu
(548 mV)
+25 dBu
(13.8 V)
CH 4 (Hi-Z) Phone
MIC
ON 1 MΩ
10 kΩ
Lines
-50 dBu
(2.45 mV)
-33 dBu
(17.3 mV)
-5 dBu
(436 mV)
Phone jack
*4
(Unbalanced)
LINE
-20 dBu
(77.5 mV)
-3 dBu
(548 mV)
+20 dBu
(7.75 V)
CH 5/6, 7/8
XLR
——
3 kΩ
50–600 Ω
Mics
-60 dBu
(0.775 mV)
-43 dBu
(5.48 mV)
-15 dBu
(138 mV)
XLR-3-31
*5
(Balanced)
Phone 10 kΩ 600 Ω Lines
-20 dBu
(77.5 mV)
-3 dBu
(548 mV)
+25 dBu
(13.8 V)
Phone jack
*4
(Unbalanced)
CH 9/10, 11/12
XLR
——
3 kΩ
50–600 Ω
Mics
-60 dBu
(0.775 mV)
-43 dBu
(5.48 mV)
-15 dBu
(138 mV)
XLR-3-31
*5
(Balanced)
Pin 10 kΩ 600 Ω Lines
-8 dBu
(316 mV)
+10 dBu
(2.45 V)
+25 dBu
(13.8 V)
RCA pin
(Unbalanced)
CH 11/12
Mini
jack
10 kΩ 600 Ω Lines
-8 dBu
(316 mV)
+10 dBu
(2.45 V)
+25 dBu
(13.8 V)
Stereo mini jack
*6
(Unbalanced)
Output Jack
Actual Source
Impedance
For Use with Nominal
Output level
Connector
Nominal Max. Before Clip
STEREO OUT L, R 600 Ω 10 kΩ Lines
+4 dBu
(1.228 V)
+20 dBu
(7.75 V)
Phone jack
*1
(Impedance balanced)
AUX SEND 1, 2 600 Ω 10 kΩ Lines
+4 dBu
(1.228 V)
+20 dBu
(7.75 V)
Phone jack
*1
(Impedance balanced)
REC OUT L, R 600 Ω 10 kΩ Lines
-10 dBV
(0.308 V)
+18 dBV
(7.75 V)
RCA pin
(Unbalanced)
Output Jack
Actual Source
Impedance
For Use with Nominal
Output level
Connector
1 kHz
THD+N < 1%
(CEA2006)
1 kHz
THD+N < 10%
(CEA2006)
SPEAKERS A, B < 0.1 Ω
4 Ω Speakers 600 W 710 W
Neutrik speakON
®
NL4
*1
Phone jack
*2
8 Ω Speakers 400 W 500 W
ZW11930
Technical Specifications
2
Block and Level Diagrams
MIC (XLR)
-60dBu (SW:MIC)–
-30dBu (SW:LINE)
LINE (PHONE)
-50dBu (SW:MIC)–
-20dBu (SW:LINE)
CH1–3
MIC (XLR)
-60dBu (SW:MIC)–
-30dBu (SW:LINE)
LINE (PHONE)
-50dBu (SW:MIC)–
-20dBu (SW:LINE)
CH4
CH INPUT
CH INPUT
CH5/6, 7/8
MIC [-60dBu]
LINE
L/MONO [-20dBu]
LINE
R [-20dBu]
ST CH INPUT
CH9/10, 11/12
MIC [-60dBu]
LINE
L [-8dBu]
LINE
R [-8dBu]
Only CH11/12
(CH9/10:bypass)
ST CH INPUT
+48V
PHANTOM +48V
FOOT SWITCH
-10dB
Hi-Z
Hi-Z
-10dB
HA
COMP
LOW
MID
HIGH
3-Stage EQ
COMP
COMP
LOW
MID
HIGH
3-Stage EQ
COMP
HPF
80Hz
MIC
LINE
HA
MIC
LINE
SUM
HA
HA
SUM
SUM
SUM
HPF
3-Stage EQ
LOW
MID
HIGH
3-Stage EQ
3-Stage EQ
LOW
MID
HIGH
3-Stage EQ
Signal
indicator
LEVEL
Signal
indicator
Signal
indicator
Signal
indicator
Signal
indicator
FX ON
LEVEL
LEVEL
LEVEL
FX RTN
LEVEL
AUX2/FX
AUX1
AUX2/FX
AUX1
AUX2/FX
AUX1
AUX2/FX
AUX1
AUX1
STEREO L
STEREO R
AUX2/FX
AUX1
STEREO L (non MUTE)
STEREO R (non MUTE)
AUX1 (non MUTE)
Digital EFFECT
PARAMETER
DA
AD
PROGRAM
DA
DSP
L
R
IN
AD
AD
STANDBY
DA
BA
L
AUX1
R
AUX2
BA
BA
BA
DA
DA
DA
DA
DA
AD
AD
Digital Audio Section
FEEDBACK
SUPPRESSOR
GRAPHIC
EQUALIZER
FEEDBACK
SUPPRESSOR
STEREO
LEVEL
AMPLIFIER
MODE
STEREO
LIMIT PROTECTION
CHA CHBCHA CHB
LIMITER
SPEAKER
PROCESSOR
L+R/AUX1
BASS
BOOST
MENU
CONTROL
GEQ ACCESS
STEREO
AUX1
AUX2
LCD Display
AUX1
LEVEL
AUX2
LEVEL
FEEDBACK
SUPPRESSOR
GRAPHIC
EQUALIZER
GRAPHIC
EQUALIZER
FEEDBACK
SUPPRESSOR
POWER
AMP
POWER
AMP
PEAK
+10
+6
+3
0
-3
-6
-10
-15
-20
-25
-30
REC OUT L
[-10dBV]
REC OUT R
[-10dBV]
SPEAKERS A
L/L+R
SPEAKERS B
R/AUX1
STEREO OUT L/MONO
[+4dBu]
STEREO OUT R
[+4dBu]
AUX1 SEND
[+4dBu]
AUX2 SEND
[+4dBu]
+30dBu
+20dBu
+10dBu
0dBu
-10dBu
-20dBu
-30dBu
-40dBu
-50dBu
-60dBu
+40dBu
CH1–4
CH INPUT
CH5/6–11/12
ST CH INPUT (MIC)
CH5/6, 7/8
ST CH INPUT (LINE)
CH9/10, 11/12
ST CH INPUT (LINE)
+30dBu
+20dBu
+10dBu
0dBu
-10dBu
-20dBu
-30dBu
-40dBu
-50dBu
-60dBu
+40dBu
Clipping Level:
[+8dBu]
Clipping Level:
[+20dBu]
SPEAKERS Maximum Level:
[400W@8Ω (+37.3dBu)]
[600W@4Ω (+36dBu)]
SPEAKERS:
[150W@4Ω (+30dBu)]
STEREO OUT: [+4dBu]
AUX1, AUX2 SEND: [+4dBu]
Maximum Input Level:
[+25dBu]
ST CH INPUT LINE:
[-20dBu]
Maximum Input Level:
[+25dBu]
ST CH INPUT LINE:
[-8dBu]
Clipping Level:
[+20dBu]
Clipping Level:
[+20dBu]
Clipping Level:
[+3dBu]
Clipping Level:
[+18dBV]
REC OUT:
[-10dBV]
STEREO L/R
AUX2/FX (CH1–4)
AUX2/FX (CH5/6–11/12)
AUX1 (CH1–4)
AUX1 (CH5/6–11/12)
Maximum Input Level (PHONE):
[+25dBu]
Maximum Input Level (XLR):
[+15dBu]
Maximum Input Level:
[+15dBu]
CH INPUT LINE (PHONE):
[-20dBu] @MIC/LINE=LINE
CH INPUT MIC (XLR)
[-30dBu] @MIC/LINE=LINE
CH INPUT LINE (PHONE):
[-50dBu] @MIC/LINE=MIC
CH INPUT MIC (XLR):
[-60dBu] @MIC/LINE=MIC
ST CH INPUT MIC:
[-60dBu]
Manual Development Group
© 2016 Yamaha Corporation
Published 05/2016 POSG-A1
Printed in Malaysia
  • Page 1 1
  • Page 2 2

Yamaha EMX7 spécification

Catégorie
Mélangeurs audio
Taper
spécification
Ce manuel convient également à