Dometic RM10.5(S)(T), RMS10.5(X)(S)(T) Guide d'installation

RM10.5(S)(T), RMS10.5(X)(S)(T)

Absorber refrigerator

Installation Manual. . . . . . . . . . . . . . . . . . . . 15

Absorber-Kühlschrank

Montageanleitung. . . . . . . . . . . . . . . . . . . . 31

Réfrigérateur à absorption

Instructions de montage . . . . . . . . . . . . . . .48

Nevera con extractor

Instrucciones de montaje . . . . . . . . . . . . . .65

Frigorífico de absorção

Instruções de montagem . . . . . . . . . . . . . .82

Frigorifero ad assorbimento

Indicazioni di montaggio . . . . . . . . . . . . . .99

Absorptiekoelkast

Montagehandleiding . . . . . . . . . . . . . . . . 116

Absorber-køleskab

Monteringsvejledning. . . . . . . . . . . . . . . .132

Absorptionskylskåp

Monteringsanvisning. . . . . . . . . . . . . . . . .148

Absorbsjons-kjøleskap

Monteringsanvisning . . . . . . . . . . . . . . . . 163

Absorptiojääkaappi

Asennusohje . . . . . . . . . . . . . . . . . . . . . . . 179

Абсорбционный холодильник

Инструкция по монтажу. . . . . . . . . . . . . . 194

Lodówka absorpcyjna

Instrukcja montażu . . . . . . . . . . . . . . . . . . 211

Absorpčná chladnička

Návod na montáž . . . . . . . . . . . . . . . . . . . 228

Absorpční lednička

Návod k montáži . . . . . . . . . . . . . . . . . . . . 244

Abszorberes hűtőszekrény

Szerelési útmutató . . . . . . . . . . . . . . . . . .260

Absorpcijski hladilnik

Navodilo za montažo . . . . . . . . . . . . . . . . 277

Ψυγείο υγραερίου/ρεύματος

Οδηγίες τοποθέτησης. . . . . . . . . . . . . . 293

EN

DE

FRFR

ES

PT

IT

NL

DA

SV

NO

FI

RU

PL

SK

CS

HU

SL

EL

REFRIGERATION

10-SERIES

protected by copyright and design law. The underlying technical design and the

products contained herein may be protected by design, patent or be patent

pending. The trademarks mentioned in this manual belong to Dometic Sweden AB.

All rights are reserved.

RM10.5(S)(T), RMS10.5(X)(S)(T)

3

NOTICE

d 90°

548

400

216

400

118

548

523

821

523

821

523

821

RM10.5S, RM10.5T

RMS10.5S, RMS10.5T

216

455

118

603

RMS10.5XS, RMS10.5XT

5050 50

1

RM10.5(S)(T), RMS10.5(X)(S)(T)

4

D

C

H

A

W

B

2

1

2

1

3

RM10.5(S)(T), RMS10.5(X)(S)(T)

5

 750 mm

< 750 mm

 534 mm

< 534 mm

1

4

15 – 25 mm

> 25 mm

5

RM10.5(S)(T), RMS10.5(X)(S)(T)

6

 900 mm

15 – 25 mm

 684 mm

15 – 25 mm

1

6

RM10.5(S)(T), RMS10.5(X)(S)(T)

7

≥ 300 mm

1 2

7

RM10.5(S)(T), RMS10.5(X)(S)(T)

8

A

B

< 5 mm

C

5 mm – 10 mm

3

1

2

1

4

8

RM10.5(S)(T), RMS10.5(X)(S)(T)

9

t 40 mm

1

1 2

9

1

2

3 4

5

LS 200

0

a

b

RM10.5(S)(T), RMS10.5(X)(S)(T)

10

2.

1.

c

1.

2.

3.

d

1

2

e

f

RM10.5(S)(T), RMS10.5(X)(S)(T)

11

g

h

1

2

i

2

3

1

j

RM10.5(S)(T), RMS10.5(X)(S)(T)

12

bk bn bu rd pk vt wh

EN Black Brown Blue Red Pink Violet White

DE Schwarz Braun Blau Rot Pink Violett Weiß

FR Noir Marron Bleu Rouge Rosa Violeta Blanc

ES Negro Marrón Azul Rojo Rose Lila Blanco

PT Preto Castanho Azul Vermelho Cor de rosa Violeta Branco

IT Nero Marrone Blu Rosso Rosa Violetto Bianco

13

12

AC 230–240 V

E

87

85

86 30

X6

X4

2A FUSE

X07

S+ Optional

X2

20

11

15161718

765

8910

24

25

14

2122

X32

X07X07

23

19

1

2

rd (+)

L PE N

A

B

C

D

E

F

WAGO

gy (gn)

D+ (wh)

rd (+)

pk (ye) (+)

bk (bn)(–)

bn (–)

3

4

k

RM10.5(S)(T), RMS10.5(X)(S)(T)

13

NL Zwart Bruin Blauw Rood Roze Paars Wit

DA Sort Brun Blå Rød Lyserøde Violet Hvid

SV Svart Brun Blå Röd Rosa Violett Vit

NO Svart Brun Blå Rød Rosa Fiolett Hvit

FI Musta Ruskea Sininen Punainen Pinkki Violetti Valkoinen

RU Черный Коричневый Синий Красный Розовый Фиолетовый Белый

PL Czarny Brązowy Niebieski Czerwony Różowy Fioletowy Biały

SK Čierna Hnedá Modrá Červená Ružová Fialová Biela

CS Černá Hněda Modrá Červená Růžová Fialová Bílá

HU Fekete Barna Kék Piros Rózsaszín Ibolya Fehér

SL Črna Rjav Moder Rdeč Roza Vijolična Bel

EL Μαύρος Καφέ Μπλε Κόκκινος ροζ βιολέτα Άσπρος

bk bn bu rd pk vt wh

RM10.5(S)(T), RMS10.5(X)(S)(T)

14

15 A

ABC

DE F

2 A

12 Vg

CC

F

D(–)

A(+)

B

E

D+

CI-BUS

t

Ø 2,5 mm²

,

,,

,,,

t

Ø 0,75 mm²

<6 m = Ø 6 mm²

>6 m = Ø 10 mm²

S+

l

EN

RM10.5(S)(T), RMS10.5(X)(S)(T) Explanation of symbols

15

Please read these instructions carefully and follow all instructions, guidelines, and warnings included in this product manual in order to ensure

that you install, use, and maintain the product properly at all times. These instructions MUST stay with this product.

By using the product, you hereby confirm that you have read all instructions, guidelines, and warnings carefully and that you understand and

agree to abide by the terms and conditions as set forth herein. You agree to use this product only for the intended purpose and application

and in accordance with the instructions, guidelines, and warnings as set forth in this product manual as well as in accordance with all appli-

cable laws and regulations. A failure to read and follow the instructions and warnings set forth herein may result in an injury to yourself and

others, damage to your product or damage to other property in the vicinity. This product manual, including the instructions, guidelines, and

warnings, and related documentation, may be subject to changes and updates. For up-to-date product information, please visit docu-

ments.dometic.com, dometic.com.

I

Table of contents

1 Explanation of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

2 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

3 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

4 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

5 Installing the refrigerator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

6 Connecting the refrigerator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

7 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

8 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

1 Explanation of symbols

!

A

NOTE

You can find details on the operation in the operating manual.

WARNING!

Safety instruction: Indicates a hazardous situation that, if not avoided,

could result in death or serious injury.

CAUTION!

Safety instruction: Indicates a hazardous situation that, if not avoided,

could result in minor or moderate injury.

NOTICE!

Indicates a situation that, if not avoided, can result in property damage.

EN

Safety instructions RM10.5(S)(T), RMS10.5(X)(S)(T)

16

I

2 Safety instructions

!

WARNING! Failure to obey these warnings could result in death

or serious injury.

Explosion hazard

• Never open the absorber unit. It is under high pressure and can cause

injury if it is opened.

• Only operate the device at the pressure shown on the type plate.

Only use pressure controllers with a fixed setting which comply with

the national regulations (in Europe EN 12864).

Fire hazard

• Ensure clean and residue-free handling if silicon sealant or similar is

used. There is a risk of fire if silicone filaments come into contact with

hot parts or naked flames.

• Never use a naked flame to check the device for leaks.

• Only use propane or butane gas (not natural gas).

Health hazard

• Do not operate the device if it is visibly damaged.

• If the AC power cable for this device is damaged, it must be replaced

by the manufacturer, a service agent or a similarly qualified person in

order to prevent safety hazards.

• This device may only be repaired by qualified personnel. Inadequate

repairs may cause serious hazards.

Risk of asphyxiation

• Dismantle all device doors for the disposal of the old device and leave

the shelves in the device to prevent accidental enclosure and suffoca-

tion.

!

CAUTION! Failure to obey these cautions could result in minor or

moderate injury.

Electrical shock

• Before starting the device, ensure that the power supply line and the

plug are dry.

NOTE

Supplementary information for operating the product.

EN

RM10.5(S)(T), RMS10.5(X)(S)(T) Accessories

17

Risk of crushing

• Do not put your fingers into the hinge.

A

NOTICE! Damage hazard

• Only hold the device at the body of the device during transport. Never

hold the device at the absorber unit, the cooling fins, the gas pipes,

the door or the control panel.

• Make sure that the device circuit is not damaged during

transportation. The refrigerant in the device circuit is highly

flammable.

In the event of any damage to the device circuit (smell of ammonia):

– Switch off the device if applicable.

– Avoid naked flames and sparks.

– Air the room well.

• Do not install the device near naked flames or other heat sources (heat-

ers, direct sunlight, gas ovens etc.).

• Danger of overheating!

Always ensure sufficient ventilation so that the heat generated during

operation can dissipate. Make sure that the device is sufficiently far

away from walls and other objects so that the air can circulate.

• Check that the voltage specification on the type plate is the same as

that of the power supply.

• Do not open the refrigerant circuit under any circumstances.

• Only use the AC connection cable supplied to connect the device to

the AC mains.

• Only use cables with a suitable size.

• Never pull the plug out of the socket by the connection cable.

• The device may not be exposed to rain.

3Accessories

Description

Flexible gas piping

Seal for draft-proof installation for gaps of 1 – 5 mm (fig. 8 B, page 7)

Seal for draft-proof installation for gaps of 5 – 10 mm (fig. 8 C, page 7)

Winter cover WA 130 for the ventilation grill LS 200

EN

Intended use RM10.5(S)(T), RMS10.5(X)(S)(T)

18

4 Intended use

The device is suitable for:

• Installation in caravans and motor homes

• Cooling, deep-freezing and storing food

The device is not suitable for:

• Storing medications

• Storing corrosive substances or substances that contain solvents

• Quick-freezing food

This product is only suitable for the intended purpose and application in accordance

with these instructions.

This manual provides information that is necessary for proper installation and/or

operation of the product. Poor installation and/or improper operating or mainte-

nance will result in unsatisfactory performance and a possible failure.

The manufacturer accepts no liability for any injury or damage to the product

resulting from:

• Incorrect assembly or connection, including excess voltage

• Incorrect maintenance or use of spare parts other than original spare parts

provided by the manufacturer

• Alterations to the product without express permission from the manufacturer

• Use for purposes other than those described in this manual

Dometic reserves the right to change product appearance and product

specifications.

Adapter cable

• WAGO to CEE

• WAGO to UK

• WAGO to JST

• WAGO to MATE-N-LOK

Optional Fan Kit REF-FANKIT

Optional Battery pack Pack R10-BP for stand-alone gas operation

Optional storage kit

Description

EN

RM10.5(S)(T), RMS10.5(X)(S)(T) Installing the refrigerator

19

5 Installing the refrigerator

!

You find the instructions manual for changing the door stop and the decorative

plate online at: “dometic.com/manuals”.

The device is suitable for installation in:

• caravans

• motor homes

5.1 Preparing the installation

A

When installing the refrigerator, note the following:

• Ensure that the floor is solid and level.

Park the vehicle horizontally for this purpose.

• Ensure that the refrigerator is level.

• The refrigerator must be installed so that

– it is easily accessible for service work

– easy to de-install and install

– can be easily removed from the vehicle

• The refrigerator must be installed in a recess so that it stands secure when the

vehicle is in motion. Note the following dimensions (fig. 1, page 3 and fig. 2,

page 4):

CAUTION! Health hazard

To avoid a hazard due to instability of the device, it must be fixed in

accordance with the instructions.

NOTICE!

• The refrigerator may not be installed in the rear of mobile homes with

the door pointing in the direction of travel.

• Use exclusively original Dometic ventilation grills to ensure safe

operation.

RM10.5(S)(T) RMS10.5(S)(T) RMS10.5X(S)(T)

Refrigerator Overall dimension in mm

Height (A) 821 821 821

Width (B) 523 523 523

Depth (C)

(excludes control knob 5 mm)

548 548 603

EN

Installing the refrigerator RM10.5(S)(T), RMS10.5(X)(S)(T)

20

• The outer wall must be fitted with an air inlet vent (fig. 3 1, page 4) and an outlet

vent (fig. 3 2, page 4) with ventilation grills so that the heat generated can be

easily released to the outside:

– Air inlet vent: Fit ventilation grill as flush as possible with the base of the instal-

lation niche.

– Outlet vent: fit as far above the refrigerator as possible.

– The distance between the air inlet and outlet vents must be at least 750 mm

for RM10.5 and 534 mm for RMS10.5 (fig. 4, page 5).

• Fit a heat conduction plate (fig. 4 1, page 4) above the refrigerator so that the

heat does not accumulate in the vehicle.

• The distance between the refrigerator and the rear wall must be at least 15 mm

but no more than 25 mm.

• A distance of more than 25 mm between the refrigerator and rear wall leads to

poor performance and increases the power consumption of the refrigerator.

Reduce the space behind the refrigerator to create adequate air inlet and outlet

ventilation (fig. 5, page 5). Use a ventilation plate, for example, to do this.

• If the minimum distance between the air inlet and outlet vents cannot be met, a

roof vent must be installed instead of the air outlet vent.

– The roof vent should be installed directly above the back of the refrigerator as

far as this is possible. Use an air duct (fig. 6 1, page 5) if you need to install

the roof vent offset; otherwise, heat will accumulate there.

– The distance between the air inlet vent and the roof vent must be at least

900 mm for RM10.5 and 684 mm for RMS10.5 (fig. 6, page 6).

– If a roof air conditioner is provided, the distance between the roof vent

(fig. 7 1, page 7) and the air outlet of the roof air conditioner (fig. 7 2,

page 7) must be at least 300 mm.

• The refrigerator must not be installed at the side of the air inlet and outlet vents as

this leads to poor performance and increases the power consumption of the

refrigerator.

• The air inlet and outlet vents must not be covered by vehicle parts (such as an

open door or by installing accessories such as bicycle racks) while operating.

Recess Dimension in mm

Height (H) 824 824 824

Width (W) 525.5 525.5 525.5

Depth (D) 563 563 618

RM10.5(S)(T) RMS10.5(S)(T) RMS10.5X(S)(T)

Refrigerator Overall dimension in mm

La page charge ...

Dometic RM10.5(S)(T), RMS10.5(X)(S)(T) Guide d'installation

Ce manuel convient également à

Dometic RM10.5(S)(T), RMS10.5(X)(S)(T) Guide d'installation

dans d''autres langues

Documents connexes

Autres documents