Indesit ARTL 82 (EX) Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi
GB
1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washing machine
and starting a wash cycle, 4-5
Control panel
Indicator lights
How to open and shut the drum
Starting a wash cycle
Wash cycles, 6
Table of wash cycles
Personalisation, 7
Setting the temperature
Functions
Detergents and laundry, 8
Detergent dispenser drawer
Bleach cycle
Preparing the laundry
Garments requiring special care
Load balancing system
Precautions and tips, 9
General safety
Disposal
Saving energy and respecting the environment
Care and maintenance, 10
Cutting off the water or electricity supply
Cleaning the washing machine
Caring for your appliance door and drum
Cleaning the pump
Checking the water inlet hose
How to clean the detergent dispenser
Troubleshooting, 11
Service, 12
ARTL 82
Instructions for use
WASHING MACHINE
English,1
GB
Français,13
FR
2
GB
Installation
Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction
manual accompanies the washing machine to inform
the new owner as to its operation and features.
Read these instructions carefully: they contain vital
information on installation, use and safety.
Unpacking and levelling
Unpacking
1. Unpack the
washing machine.
2. Check whether the
washing machine has
been damaged during
transport. If this is the
case, do not install it
and contact your
retailer.
3. Remove the four
protective screws and
the rubber washer
with the respective
spacer, situated on
the rear of the
appliance (see figure).
4. Seal the gaps using the plastic plugs provided.
5. Keep all the parts: you will need them again if
the washing machine needs to be moved to
another location.
Warning: should the screws be re-used, make sure
you fasten the shorter ones at the top.
Packaging materials are not children's toys.
Levelling
Your machine may make a considerable amount of
noise if the two front feet have not been adjusted
correctly.
1. Install the washing
machine on a flat
sturdy floor, without
resting it up against
walls, furniture cabinets
or other.
2. If the floor is not
perfectly level, com-
pensate for any
unevenness by
tightening or loosening
the adjustable front feet (see figure); the angle of
inclination, measured according to the worktop,
must not exceed 2°.
Levelling your appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting
during operation. If it is placed on a fitted or loose
carpet, adjust the feet in such a way as to allow
enough room for ventilation beneath the washing
machine.
Electric and water connections
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it to a
cold water tab using a 3/
4 gas threaded
connection (see figure).
Before performing the
connection, allow the
water to run freely until it
is perfectly clear.
2. Connect the other
end of the water inlet
hose to the washing
machine, screwing it
onto the appliance's
cold water inlet, situated
on the top right-hand
side on the rear of the
appliance (see figure).
3. Make sure there are no kinks or bends in the hose.
The water pressure at the tap must be within the
values indicated in the Technical details table
(on the next page).
If the water inlet hose is not long enough, contact
a specialist store or an authorised serviceman.
GB
3
Technical data
Model
ARTL 82
Dimensions
width 40 cm
height 85 cm
depth 60 cm
Capacity
from 1 to 5 kg
Electrical
connections
please refer to the technical data
plate fixed to the machine
Water connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 42 litres
Spin speed
up to 800 rotations per minute
Energy rated
programmes
according to
regulation
EN 60456
programme 7; temperature 60°C;
using a load of 5 kg.
This appliance conforms to the
following EC Directives:
- 89/336/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent modifications
- 2002/96/EC
- 2006/95/EC (Low Voltage)
Connecting the drain hose
Connect the drain hose,
without bending it, to a
drainage duct or a wall
drain located at a height
between 65 and 100 cm
from the floor;
alternatively, rest it on
the side of a washbasin
or bathtub, fastening the
duct supplied to the tap
(see figure). The free end
of the hose should not
be underwater.
We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity
socket, make sure that:
the socket is earthed and complies with all
applicable laws;
the socket is able to withstand the maximum power
load of the appliance as indicated in the Technical
data table (see opposite);
the power supply voltage falls within the values
indicated in the Technical data table (see opposite);
the socket is compatible with the plug of the
washing machine. If this is not the case, replace
the socket or the plug.
The washing machine must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to rain,
storms and other weather conditions.
When the washing machine has been installed, the
electricity socket must be within easy reach.
Do not use extension cords or multiple sockets.
The cable should not be bent or compressed.
The power supply cable must only be replaced by
authorised technicians.
Warning! The company shall not be held responsible
in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, using the wash cycle 2.
65 - 100 cm
4
GB
Standby mode
This washing machine, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after about 30 minutes if no
activity is detected. Press the ON-OFF button briefly
and wait for the machine to start up again.
Indicator lights
The indicator lights provide important information.
This is what they can tell you:
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has
begun, the indicator lights switch on one by one to
indicate which phase of the cycle is currently in progress.
Function buttons and corresponding indicator lights
When a function is selected, the corresponding
indicator light will illuminate.
If the selected function is not compatible with the
programmed wash cycle, the corresponding indicator
light will flash and the function will not be activated.
If a function which is incompatible with another
function selected previously, only the most recent
selection will remain active.
Wash
Rinse
Spin
Drain
End of wash cycle
ON/OFF button: switches the washing machine on
and off.
WASH CYCLE knob: programmes the wash cycles.
During the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to
select the available functions. The indicator light
corresponding to the selected function will remain lit.
TEMPERATURE knob: sets the temperature or the
cold wash cycle (see Personalisation).
WASH CYCLE PROGRESS
indicator light
s: used to monitor the progress of the
wash cycle. The illuminated indicator light shows
which phase is in progress.
LID LOCKED indicator light: indicates whether the
door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or
temporarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this
button; the corresponding indicator light will flash
orange, while the indicator light for the current wash
cycle phase will remain lit in a fixed manner. If the LID
LOCKED
indicator light is switched off, the door
may be opened.
To start the wash cycle from the point at which it was
interrupted, press this button again.
Description of the washing machine
and starting a wash cycle
TEMPERATURE
knob
WASH CYCLE PROGRESS
indicator lights
FUNCTION
buttons with
indicator lights
ON/OFF
button
LID LOCKED
indicator light
START/PAUSE
button with indicator
light
Control panel
WASH CYCLE
knob
GB
5
Lid locked indicator light
If this indicator light is on, the appliance door is locked to
prevent it from being opened accidentally; to avoid any
damage, wait for the indicator light to switch off (it will take
about three minutes) before you open the appliance door.
If the START/PAUSE indicator light (orange) flashes
rapidly at the same time as the function indicator
light, this indicates a problem has occurred (see
Troubleshooting).
How to open and to close the drum
Fig. 1
Fig. 2
Fig. 3
Fig. 4
A) Opening (Fig. 1):
Lift the external lid and open it completely.
B) Then open the drum using both hands as
shown in Fig.2:
- press the button indicated by the arrow in fig. 2
lightly downwards, with one hand firmly resting on
the doors to prevent them from suddenly opening
and hurting your fingers;
- therefore follow the appliance doors along as
these unhook and open easily.
C) Loading the washing machine (Fig. 3).
D) Shutting (Fig. 4):
- close the drum fully by first shutting the front
door followed by the rear one;
- then ensure the hooks on the front door are
perfectly housed within the seat of the rear door;
- after the hooks have clicked into position, press
both doors lightly downwards to make sure they
do not come loose;
- finally shut the external lid.
Starting a wash cycle
1. Turn the washing machine on by pressing the
ON/OFF button. All the indicator lights will turn on for
a few seconds, then only the indicator lights relative
to the selected programme settings will remain lit and
the START/PAUSE indicator light will flash.
2. Load the laundry, close the door and the lid.
3. Set the WASH CYCLE knob to the desired
programme.
4. Set the washing temperature (see
Personalisation).
5. Measure out the detergent and washing additives
(see Detergents and laundry).
6. Select the desired functions.
7. Start the wash cycle by pressing the START/
PAUSE button and the corresponding indicator light
will remain lit in a fixed manner, in green.
To cancel the set wash cycle, pause the machine by
pressing the START/PAUSE button and select a new
cycle.
8. At the end of the wash cycle the
indicator light
will switch on. The LID LOCKED indicator light will
switch off, indicating that the door may be opened.
Take out your laundry and leave the appliance door
ajar to make sure the drum dries completely.
Switch the washing machine off by pressing the ON/
OFF button.
6
GB
Wash cycles
The information contained in the table is intended as a guide only.
For all Test Institutes:
1) Test wash cycle in compliance with regulation EN 60456: set wash cycle 7 with a temperature of 60°C.
2) Long wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.
3) Short wash cycle for cottons: set wash cycle 3 with a temperature of 40°C.
Wash cycles
Table of wash cycles
Description of the wash cycle
Max
.
temp.
(°C)
Max.
speed
(rpm)
Detergents
Max.
load
(kg)
Cycle
duration
Bleach Wash
Fabric
softener
Special cycles
7
Sanitizing cycle 90°:
Extremely soiled whites.
90° 800
ll l
5165
7
Sanitizing cycle 90° (1):
Heavily soiled whites and resistant colours.
60° 800 -
ll
5 139
8
Goodnigt cycle:
Lightly soiled delicate colours.
40° 800 -
ll
3288
9
Baby cycle:
Heavily soiled delicate colours.
40° 800 -
ll
2 116
10
Shirts
40° 600 -
ll
269
11
Silk/Curtains:
For garments in silk and viscose, lingerie.
30° 0 -
ll
155
12
Wool:
For wool, cashmere, etc.
40° 600 -
ll
155
Everyday wash cycles (Daily)
1
Cotton + Prewash 90°:
Extremely soiled whites.
90° 800 -
ll
5164
2
Cotton:
Heavily soiled whites and resistant colours.
60° 800
ll l
5 138
2
Cotton (2):
Heavily soiled whites and delicate colours.
40° 800
ll l
5 123
3
Coloured Cottons (3):
Lightly soiled whites and delicate colours.
40° 800
ll l
589
4
Synthetics resistents:
Heavily soiled resistant colours.
60° 800 -
ll
2,5 85
4
Synthetics delicates:
Lightly soiled resistant colours.
40° 800 -
ll
2,5 73
5
Mix 30':
To refresh lightly soiled garments quickly (not suitable for wool,
silk and clothes which require washing by hand).
30° 800 -
ll
330
6
Mix 15':
To refresh lightly soiled garments quickly (not suitable for wool,
silk and clothes which require washing by hand).
30° 800 -
ll
1,5 15
Partials wash cycles
Rinse - 800
l
-
l
536
Spin - 800 - - - 516
Light spin - 800 - - - 2,5 12
Drain no spin - 0 - - - 52
Specials wash cycles
Sanitizing cycle (wash cycle 7). A high-temperature hygienic wash cycle (over 60°C) which requires the use of bleach.
Pour the bleach, the detergent and the additives into the relevant compartments (see paragraph entitled
Detergent dispenser drawer).
Goodnigt cycle (wash cycle 8). This is a silent cycle which can be run at night, when the electricity prices are lower. The
wash cycle is designed for cottons and synthetics. At the end of the cycle the machine stops while there is still water in
the drum; to spin and drain the laundry press the START/PAUSE button; alternatively the machine will perform the spin
cycle and drain the water automatically after 8 hours.
Baby cycle (wash cycle 9). This wash cycle can be used to remove the soiling typically caused by babies, while ensuring
that all detergent is removed from nappies in order to prevent the delicate skin of babies from suffering allergies. The
cycle has been designed to reduce the amount of bacteria by using a greater quantity of water and optimising the effect
of special disinfecting additives added to the detergent.
Mix 30 (wash cycle 5) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 30 minutes and
therefore saves both energy and time. By selecting this wash cycle (5 at 30°C), it is possible to wash different fabrics
together (except for wool and silk items), with a maximum load of 3 kg.
Mix 15(wash cycle 6) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes and
therefore saves both energy and time. By selecting this wash cycle (6 at 30°C), it is possible to wash different fabrics
together (except for wool and silk items), with a maximum load of 1.5 kg.
GB
7
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash (
).
The washing machine will automatically prevent you from selecting a temperature which is higher than the
maximum value set for each wash cycle.
Functions
The various wash functions available with this washing machine will help to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in
conjunction with the selected wash cycle.
Super Wash
Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased cycle
duration, this function offers a high-performance wash.
This function may not be used in conjunction with wash cycles 5, 6, 7, 11, 12,
, , , .
Easy iron
By selecting this function, the wash and spin cycles will be modified in order to reduce the formation of creases. At
the end of the cycle the washing machine will perform slow rotations of the drum.
For the 11 wash cycle, the machine will end the cycle while the laundry is soaking, the EASY IRON and START/
PAUSE indicator lights will flash (orange) and the RINSE phase will remain lit in a fixed manner. To drain the water
so that the laundry may be removed, press the START/PAUSE button or the EASY IRON button.
This function may not be used in conjunction with wash cycles 5, 6, 7, 8, 9, 12, , , .
Extra rinse
By selecting this function, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is
particularly useful for sensitive skin.
This function may not be used in conjunction with wash cycles 5, 6,
, , .
800-400
By selecting this function, reduces the spin speed.
! This function may not be used in conjunction with wash cycles 11,
.
Personalisation
8
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct
dose of detergent: adding too much detergent won't
necessarily make for a more efficient wash, and may
in fact cause build up on the interior of your appliance
and even pollute the environment.
Open up the detergent
dispenser and pour in
the detergent and fabric
softener, as follows.
compartment 1: Detergent for pre-wash
compartment 2: Detergent for the wash cycle
(powder or liquid)
It is recommended that you place liquid detergent
directly into the compartment using the appropriate
dosing cup.
compartment 3: Additives (softener, etc.)
When pouring the softener in compartment 3, avoid
exceeding the "max" level indicated.
The softener is added automatically into the machine
during the last wash. At the end of the wash
programme, some water will be left in compartment
3. This is used for the inlet of denser fabric softeners
into the machine, i.e. to dilute the more concentrated
softeners. Should more than a normal amount of
water remain in compartment 3, this means the
emptying device is blocked. For cleaning instructions,
see Care and maintenance.
compartment 4: Bleach
Bleach cycle
Bleaching may only be performed in conjunction with
wash cycles 2, 3, 7,
.
Pour the bleach into compartment 4; pour the
detergent and softener into the corresponding
compartments, then select one of the
abovementioned wash cycles.
This option is recommended only for very soiled
cotton garments.
Preparing the laundry
Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from
whites.
Empty all garment pockets and check the buttons.
Do not exceed the listed values, which refer to the
weight of the laundry when dry:
Durable fabrics: max. 5 kg
Synthetic fabrics: max. 2,5 kg
Delicate fabrics: max. 2 kg
Wool: max. 1 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Garments requiring special care
Shirts: use special wash cycle 10 to wash shirts in
various fabrics and colours.
It guarantees maximum care is taken of the garments
and minimises the formation of creases.
Silk: use special wash cycle 11 to wash all silk
garments. We recommend the use of special
detergent which has been designed to wash delicate
clothes.
Curtains: fold curtains and place them in a pillow
case or mesh bag. Use wash cycle 11.
Wool: Ariston is the only washing machine
manufacturer to have been awarded the prestigious
Woolmark Platinum Care endorsement (M.0508) by
the Woolmark Company, which means that all
woollen garments may be washed in the washing
machine, even those which state hand wash only
on the label. Wash cycle 12 therefore offers
complete peace of mind when washing woollen
garments in the washing machine (max. load 1 kg)
and guarantees optimal performance.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
and to distribute the load in a uniform manner, the drum
rotates continuously at a speed which is slightly greater
than the washing rotation speed. If, after several at-
tempts, the load is not balanced correctly, the machine
spins at a reduced spin speed. If the load is excessively
unbalanced, the washing machine performs the distri-
bution process instead of spinning. To encourage im-
proved load distribution and balance, we recommend
small and large garments are mixed in the load.
GB
9
Precautions and tips
This washing machine was designed and
constructed in accordance with international safety
regulations. The following information is provided for
safety reasons and must therefore be read carefully.
General safety
This appliance was designed for domestic use only.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
Do not touch the machine when barefoot or with
wet or damp hands or feet.
Do not pull on the power supply cable when
unplugging the appliance from the electricity
socket. Hold the plug and pull.
Do not touch the drained water as it may reach
extremely high temperatures.
Never force the porthole door. This could damage
the safety lock mechanism designed to prevent
accidental opening.
If the appliance breaks down, do not under any
circumstances access the internal mechanisms in
an attempt to repair it yourself.
Always keep children well away from the appliance
while it is operating.
If the appliance has to be moved, work in a group
of two or three people and handle it with the utmost
care. Never try to do this alone, because the
appliance is very heavy.
Before loading laundry into the washing machine,
make sure the drum is empty.
Disposal
Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires that
old household electrical appliances must not be
disposed of in the normal unsorted municipal waste
stream. Old appliances must be collected
separately in order to optimise the recovery and
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out "wheeled bin" symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Saving energy and respecting the
environment
Saving on detergent, water, energy and time
To avoid wasting resources, the washing machine
should be used with a full load. A full load instead
of two half loads allows you to save up to 50% on
energy.
The pre-wash cycle is only necessary on
extremely soiled garments. Avoiding it will save on
detergent, time, water and between 5 and 15%
energy.
Treating stains with a stain remover or leaving
them to soak before washing will cut down the
need to wash them at high temperatures. A
programme at 60°C instead of 90°C or one at
40°C instead of 60°C will save up to 50% on
energy.
Use the correct quantity of detergent depending
on the water hardness, how soiled the garments
are and the amount of laundry you have, to avoid
wastage and to protect the environment: despite
being biodegradable, detergents do contain
ingredients that alter the natural balance of the
environment. In addition, avoid using fabric
softener as much as possible.
If you use your washing machine from late in the
afternoon until the early hours of the morning, you
will help reduce the electricity board's peak load.
10
GB
Care and maintenance
Cutting off the water or electricity
supply
Turn off the water tap after every wash. This will
limit the wear of your appliance's water system
and also prevent leaks.
Unplug your appliance when cleaning it and during
all maintenance operations.
Cleaning your appliance
The exterior and rubber parts of your appliance can
be cleaned with a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Caring for your appliance door and
drum
Always leave the appliance door ajar to prevent
unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning
pump that does not require any maintenance.
Sometimes, small items (such as coins or buttons)
may fall into the pre-chamber that protects the
pump, situated in the lower part of the same.
Make sure the wash cycle has ended and unplug
the appliance.
How to clean the detergent dispenser
Cleaning:
Then clean the dispenser under a tap (fig. 3) using an
old toothbrush and, once the pair of siphons inserted in
the top of compartments 1 and 2 (fig. 4) have been pulled
out, check whether the same are not clogged and then
rinse them.
Reassembly:
Do not forget to reinsert the
pair of siphons into the spe-
cial housings and then to
replace the dispenser into
its seat, clicking it into place
(fig. 4, 2 and 1).
Disassembly:
Press lightly on the large
button on the front of the
detergent dispenser and
pull it upwards (fig. 1, 2).
To recover any objects that have fallen into the pre-
chamber:
1. remove the plinth at
the bottom on the front
side of the washing
machine by pulling from
the side with your
hands (see figure);
2. unscrew the lid
rotating it anticlock-
wise (see figure): a little
water may trickle out.
This is perfectly normal;
3. clean the interior
thoroughly;
4. screw the lid back on;
5. reposition the panel,
making sure the hooks
are securely in place
before you push it onto
the appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If
you see any cracks, replace it immediately: during the
wash cycles, water pressure is very strong and a
cracked hose could easily split open.
Never use hoses that have already been used.
Fig. 1 Fig. 2
Fig. 3
Fig. 4
GB
11
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see Assistance),
make sure that the problem cannot be not solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (the indicator light
for the first wash cycle stage
flashes rapidly).
The washing machine
continuously takes in and drains
water.
The washing machine does not
drain or spin.
The washing machine vibrates a
lot during the spin cycle.
The washing machine leaks.
The START/PAUSE indicator light
(orange) and the function
indicator lights flash rapidly.
There is too much foam.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or is not making contact.
There is no power in the house.
The appliance Lid is not shut properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The drain hose is not fitted at a height between 65 and 100 cm from
the floor (see Installation).
The free end of the hose is under water (see Installation).
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap,
switch the appliance off and contact the Assistance Service. If the
dwelling is on one of the upper floors of a building, there may be problems
relating to water drainage, causing the washing machine to fill with water
and drain continuously. Special anti-draining valves are available in shops
and help to avoid this inconvenience.
The wash cycle does not include draining: some wash cycles require
the drain phase to be started manually.
The EASY IRON function has been activated: To complete the wash
cycle, press the START/PAUSE button (Personalisation).
The drain hose is bent (see Installation).
The drainage duct is clogged.
The drum was not unlocked correctly during installation (see Installation).
The washing machine is not level (see Installation).
The washing machine is trapped between cabinets and walls (see Installation).
The water inlet hose is not screwed on properly (see Installation).
The detergent dispenser drawer is blocked (for cleaning instructions, see
Care and maintenance).
The drain hose is not fixed properly (see Installation).
Switch off the machine and unplug it, wait for approximately 1 minute
and then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
The detergent is not suitable for machine washing (it should display the
text for washing machines or hand and machine wash, or the like).
Too much detergent was used.
12
GB
Service
Before calling for Assistance:
Check whether you can solve the problem alone (see Troubleshooting);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Assistance Centre using the telephone number
provided on the guarantee certificate.
Always request the assistance of authorised technicians.
Have the following information to hand:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate situated on the rear of the washing machine.
FR
13
Français
Sommaire
Installation, 14-15
Déballage et mise à niveau
Raccordements eau et électricité
Premier cycle de lavage
Caractéristiques techniques
Description du lave-linge et
démarrage dun programme, 16-17
Bandeau de commandes
Voyants
Comment ouvrir et fermer le tambour
Démarrage dun programme
Programmes,18
Tableau des programmes
Personnalisations, 19
Sélection de la température
Fonctions
Produits lessiviels et linge, 20
Tiroir à produits lessiviels
Cycle blanchissage
Triage du linge
Linge ou vêtements particuliers
Système déquilibrage de la charge
Précautions et conseils, 21
Sécurité générale
Mise au rebut
Economies et respect de l'environnement
Entretien et soin, 22
Coupure de larrivée deau et du courant
Nettoyage du lave-linge
Entretien du couvercle et du tambour
Nettoyage de la pompe
Contrôle du tuyau darrivée de leau
Comment nettoyer le tiroir à produits lessiviels
Anomalies et remèdes, 23
Assistance, 24
FR
ARTL 82
Mode demploi
LAVE-LINGE
14
FR
Installation
Conservez ce mode d'emploi pour pouvoir le
consulter à tout moment. En cas de vente, de cession
ou de déménagement, veillez à ce qu'il suive toujours
le lave-linge pour que son nouveau propriétaire soit
informé sur son mode de fonctionnement et puisse
profiter des conseils correspondants.
Lisez attentivement les instructions: elles fournissent
d'importantes informations sur l'installation, l'utilisation
et la sécurité.
Déballage et mise à niveau
Déballage: enlever les 4 vis
1. Déballez le lave-linge.
2. Contrôlez que le
lave-linge n'a pas été
endommagé pendant le
transport. S'il est
abîmé, ne le raccordez
pas et contactez votre
revendeur.
3. Enlevez les quatre vis
de protection pour le
transport, le
caoutchouc et la cale,
placés dans la partie
arrière (voir figure).
4. Bouchez les trous à l'aide des bouchons plastique
fournis.
5. Conservez bien toutes ces pièces: il faudra les
remonter en cas de transport du lave-linge.
Attention: en cas de réutilisation, les vis plus
courtes doivent être montées dessus.
Les emballages ne sont pas des jouets pour enfants.
Mise à niveau
Votre appareil peut savérer bruyant si vous navez
pas bien réglé ses deux pieds avant.
1.Installez le lave-linge
sur un sol plat et rigide,
sans l'appuyer contre
des murs, des meubles
ou autre.
2. Si le sol n'est pas
parfaitement horizontal,
vissez ou dévissez les
petits pieds avant (voir
figure) pour niveler l'appareil; son angle d'inclinaison,
mesuré sur le plan de travail, ne doit pas dépasser 2°.
Une bonne mise à niveau garantit la stabilité de la
machine et évite qu'il y ait des vibrations, du bruit et
des déplacements en cours de fonctionnement. Si la
machine est posée sur de la moquette ou un tapis,
réglez les petits pieds de manière à ce qu'il y ait
suffisamment d'espace pour assurer une bonne
ventilation.
Raccordements hydrauliques et
électriques
Raccordement du tuyau d'arrivée de l'eau
1. Reliez le tuyau
d'alimentation en le
vissant à un robinet d'eau
froide à embout fileté 3/4
gaz (voir figure).
Faire couler leau jusquà
ce quelle soit limpide et
sans impuretés avant de
raccorder.
2. Raccordez le tuyau
d'alimentation au lave-
linge en le vissant à la
prise d'eau prévue, dans
la partie arrière en haut à
droite (voir figure).
3. Faites attention à ce
que le tuyau ne soit ni
plié ni écrasé.
La pression de l'eau doit être comprise entre les
valeurs indiquées dans le tableau des Caractéristiques
techniques (voir page ci-contre).
Si la longueur du tuyau d'alimentation ne suffit pas,
adressez-vous à un magasin spécialisé ou à un
technicien agréé.
FR
15
65 - 100 cm
Raccordement du tuyau de vidange
Raccorder le tuyau
dévacuation, sans le
plier, à un conduit
dévacuation ou à une
évacuation murale placés
à une distance du sol
comprise entre 65 et 100
cm;
ou bien laccrocher à un
évier ou à une baignoire,
dans ce cas, fixer le
support en plastique
fourni avec lappareil au
robinet (voir figure).
Lextrémité libre du tuyau
dévacuation ne doit pas
être plongée dans leau.
Lutilisation dun tuyau de rallonge est absolument
déconseillée mais si on ne peut faire autrement, il faut
absolument quil ait le même diamètre que le tuyau
original et sa longueur ne doit pas dépasser 150 cm.
Branchement électrique
Avant de brancher la fiche dans la prise de courant,
sassurer que:
la prise est bien reliée à la terre et est conforme aux
réglementations en vigueur;
la prise est bien apte à supporter la puissance
maximale de lappareil indiquée dans le tableau des
Caractéristiques techniques (voir ci-contre);
la tension dalimentation est bien comprise entre les
valeurs figurant dans le tableau des Caractéristiques
techniques (voir ci-contre);
la prise est bien compatible avec la fiche du lave-
linge. Autrement, remplacer la prise ou la fiche.
Le lave-linge ne doit pas être installé dehors, même
à labri, car il est très dangereux de le laisser exposé
à la pluie et aux orages.
Après installation du lave-linge, la prise de courant
doit être facilement accessible.
Nutiliser ni rallonges ni prises multiples.
Le câble ne doit être ni plié ni trop écrasé.
Le câble dalimentation ne doit être remplacé que
par des techniciens agréés.
Attention! Nous déclinons toute responsabilité en cas
de non-respect des normes énumérées ci-dessus.
Premier cycle de lavage
Avant la première mise en service de lappareil,
effectuer un cycle de lavage avec un produit lessiviel
mais sans linge et sélectionner le programme 2.
Caractéristiques techniques
Modèle
ARTL 82
Dimensions
largeur 40 cm
hauteur 85 cm
profondeur 60 cm
Capaci
de 1 à 5 kg
Raccordements
électriques
Voir la plaque signalétique appliquée
sur la machine
Raccordements
hydrauliques
pression maximale 1 MPa (10 bar)
pression minimale 0,05 MPa (0,5 bar)
capacité du tambour 42 litres
Vitesse
d'essorage
jusqu'à 800 tours minute
Programmes de
contrôle selon la
norme EN 60456
programme 7; température 60°C;
effectavec une charge de 5 kg.
Cet appareil est conforme aux
Directives Communautaires suivantes:
- 89/336/CEE du 03/05/89
(Compatibilité électromagnétique) et
modifications suivantes
- 2002/96/CE
- 2006/95/CE (Basse Tension)
16
FR
Stand-by
Ce lave-linge, conformément aux nouvelles normes
en vigueur dans le domaine de l'économie d'énergie,
est équipée d'un système d'extinction automatique
(veille) activé après environ 30 minutes d'inutilisation.
Appuyez brièvement sur la touche MARCHE/ARRÊT
et attendre que la machine soit réactivée.
Voyants
Les voyants fournissent des informations importantes.
Voilà ce quils signalent:
Voyants phase en cours
Une fois que le cycle de lavage sélectionné a
démarré, les voyants sallument progressivement pour
indiquer son stade davancement:
Touches fonction et voyants correspondants
La sélection dune fonction entraîne lallumage du
voyant correspondant.
Si la fonction sélectionnée est incompatible avec le
programme sélectionné, le voyant correspondant se
met à clignoter et la fonction nest pas activée.
En cas de sélection dune fonction incompatible avec
une autre précédemment sélectionnée, la seule à
être activée sera celle choisie en dernier.
Lavage
Rinçage
Vidange
Fin de Lavage
Touche MARCHE/ARRÊT: pour allumer ou éteindre
le lave-linge.
Bouton PROGRAMMES: pour sélectionner les
programmes. Pendant le programme, le bouton ne
tournera pas.
Touches avec voyants FONCTION: pour sélectionner
les fonctions disponibles. Le voyant correspondant à
la fonction sélectionnée restera allumé.
Bouton TEMPÉRATURE: pour sélectionner la
température ou un lavage à froid (voir
Personnalisations).
Voyants DÉROULEMENT CYCLE: pour suivre le
stade davancement du programme de lavage.
Le voyant allumé indique la phase de lavage en
cours.
Voyant COUVERCLE VERROUILLÉ: indique si la
porte est verrouillée (voir page ci-contre).
Touche avec voyant MARCHE/PAUSE: pour
démarrer les programmes ou les interrompre
momentanément.
N.B.: pour effectuer une pause du lavage en cours,
appuyer sur cette touche, le voyant correspondant se
mettra à clignoter en orange tandis que celui de la
phase en cours restera allumé fixe. Si le voyant
COUVERCLE VERROUILLÉ
est éteint, on peut
ouvrir la porte.
Pour faire redémarrer le lavage exactement de
lendroit il a été interrompu, appuyer une nouvelle
fois sur la touche.
Description du lave-linge et
démarrage dun programme
Bouton
TEMPÉRATURE
Voyants
DÉROULEMENT
CYCLE
Touches avec voyants
FONCTION
Touche
MARCHE/
ARRÊT
Voyant
COUVERCLE
VERROUILLÉ
Touche avec voyant
MARCHE/
PAUSE
Bandeau de commandes
Bouton
PROGRAMMES
Essorage
FR
17
Fig. 1
Fig. 2
Fig. 3
Fig. 4
A) Ouvrez le couvercle (Fig. 1). Soulevez le
Couvercle externe et ouvrez le complètement;
B) Ouvrez ensuite les Portes du tambour à laide
de vos deux mains comme indiqué sur la Fig. 2):
appuyez sur la touche indiquée par la flèche sur la
Fig. 2) et tout en appuyant légèrement vers le bas
posez une main pour éviter que les portes ne vous
fassent mal aux adoigts en souvrant soudainement;
accompagnez dans leur mouvements les portes qui
se décrocheront et souvriront facilement.
C) Introduisez le linge (Fig. 3).
D) Fermer (Fig. 4).
refermez bien le tambour en baissant dabord la
porte antérieure et posez ensuite la porte
postérieure;
faites attention à parfaitement positionner les
crochets de la porte antérieure dans leur siège
dans la porte postérieure;
vous entendrez un clac qui confirmera la
bonne fixation;
appuyez alors légèrement vers le bas sur les
deux portes qui ne doivent pas se décrocher;
fermez enfin le couvercle externe.
Démarrage dun programme
1. Allumer le lave-linge en appuyant sur la touche
MARCHE/ARRÊT
. Tous les voyants s'allumeront
pendant quelques secondes, ne resteront ensuite
allumés que les voyants correspondant aux sélections
du programme en cours et le voyant MARCHE/PAUSE
se mettra à clignoter.
2. Charger le linge et fermer les portes et le
couvercle.
3. Sélectionner à laide du bouton PROGRAMMES le
programme désiré.
4. Sélectionner la température de lavage (voir
Personnalisations).
5. Verser les produits lessiviels et les additifs (voir
Produits lessiviels et linge).
6. Sélectionner les fonctions désirées.
7. Appuyer sur la touche MARCHE/PAUSE pour
démarrer le programme, le voyant correspondant vert
restera allumé en fixe.
Pour annuler le cycle sélectionné, appuyer sur la
touche MARCHE/PAUSE pour placer lappareil en
pause et choisir un nouveau cycle.
8. A la fin du programme, le voyant
sallume. Le
voyant COUVERCLE VERROUILLÉ séteint pour
signaler que le couvercle peut être ouvert. Sortir le
linge et laisser le couvercle entrouvert pour faire
sécher le tambour.
Eteindre le lave-linge en appuyant sur la touche
MARCHE/ARRÊT.
Voyant couvercle verrouillé
Le voyant allumé indique que le couvercle est
verrouillé pour empêcher toute ouverture accidentelle.
Pour éviter dendommager lappareil, attendre que le
voyant cesse de clignoter avant douvrir la porte
(l'attente est denviron trois minutes).
Un clignotement rapide du voyant MARCHE/PAUSE
(orange) simultané à celui des fonctions signale une
anomalie (voir Anomalies et remèdes).
Comment ouvrir et fermer le tambour
18
FR
Programmes
Les données dans le tableau sont reprises à titre indicatif.
Pour tous les instituts qui effectuent ces tests :
1) Programme de contrôle selon la norme EN 60456: sélectionner le programme 7 et une température de 60°C.
2) Programme coton long: sélectionner le programme 2 et une température de 40°C.
3) Programme coton court: sélectionner le programme 3 et une température de 40°C.
Programmes
Tableau des programmes
Description du Programme
Te m p .
maxi.
(°C)
Vitesse
maxi
(tours
minute)
Produits lessiviels
Charge
maxi
(Kg)
Durée
cycle
Eau
de
Javel
Lavage
Adou
-
cissant
Programmes Spécial
7
Anti-bactérien 90°C:
blancs extrêmement sales.
90° 800
ll l
5 165
7
Anti-bactérien 90°C (1):
blancs et couleurs résistantes très sales.
60° 800 -
ll
5 139
8
Bonne Nuit:
couleurs délicates peu sales.
40° 800 -
ll
3288
9
Bébé:
couleurs délicates très sales.
40° 800 -
ll
2 116
10
Chemises
40° 600 -
ll
269
11
Soie/Voilages:
pour linge en soie, viscose, lingerie.
30° 0 -
ll
155
12
Laine:
pour laine, cachemire, etc.
40° 600 -
ll
155
Programmes Quotidien
1
Coton Prélavage 90°C:
blancs extrêmement sales.
90° 800 -
ll
5 164
2
Coton:
blancs et couleurs résistantes très sales.
60° 800
ll l
5 138
2
Coton (2):
blancs et couleurs délicates très sales.
40° 800
ll l
5 123
3
Coton (3):
blancs peu sales et couleurs délicates.
40° 800
ll l
589
4
Synthétique:
couleurs résistantes très sales.
60° 800 -
ll
2,5 85
4
Synthétique:
couleurs résistantes peu sales.
40° 800 -
ll
2,5 73
5
MIX 30':
pour rafrchir rapidement du linge peu sale (ne convient pas pour
la laine, la soie et le linge à laver à la main).
30° 800 -
ll
330
6
MIX 15':
pour rafrchir rapidement du linge peu sale (ne convient pas pour
la laine, la soie et le linge à laver à la main).
30° 800 -
ll
1,5 15
Cycle
Rinçage - 800
l
-
l
536
Essorage - 800 - - - 516
Essorage délicat - 800 - - - 2,5 12
Vidange - 0 - - - 52
Programmes spéciaux
Anti-bactérien (programme 7). Un programme hautes températures qui prévoit lutilisation de produits javelisés à des
températures supérieures à 60°C. Pour blanchir, verser le produit javelisé, les lessives et les additifs dans les
compartiments correspondants (voir paragraphe Tiroir à produits lessiviels).
Bonne nuit (programme 8). Cest un cycle silencieux qui permet de faire fonctionner le lave-linge la nuit quand le tarif
délectricité est plus bas. Ce programme est spécialement conçu pour les synthétiques et le coton. A la fin du cycle
lappareil sarrête, cuve pleine. Pour procéder à lessorage et à la vidange, appuyer sur la touche MARCHE/PAUSE, à
défaut, lappareil procédera automatiquement au bout de 8 heures à lessorage et à la vidange de leau.
Bébé (programme 9). Programme spécial, idéal pour le lavage des vêtements denfants souvent très sales, il élimine
toute trace de lessive du linge pour protéger leur peau délicate et éviter tout risque dallergie. Spécialement conçu pour
diminuer la charge bactérienne, ce cycle utilise une plus grande quantité deau et optimise leffet des additifs
désinfectants spécifiques ajoutés à la lessive.
Mix 30 (programme 5) spécialement conçu pour laver du linge peu sale en un rien de temps: il ne dure que 30 minutes
et permet ainsi de faire des économies dénergie et de temps. La sélection de ce programme (5 à 30°C) permet de
laver ensemble des textiles différents (sauf laine et soie) en ne dépassant pas 3 kg de charge.
Mix 15 (programme 6) spécialement conçu pour laver du linge peu sale en un rien de temps: il ne dure que 15 minutes
et permet ainsi de faire des économies dénergie et de temps. La sélection de ce programme (6 à 30°C) permet de
laver ensemble des textiles différents (sauf laine et soie) en ne dépassant pas 1,5 kg de charge.
FR
19
Sélection de la température
Tourner le bouton TEMPÉRATURE pour sélectionner la température de lavage (voir Tableau des programmes).
La température peut être abaissée jusquau lavage à froid (
).
La machine interdira automatiquement toute sélection dune température supérieure à la température maximale
prévue pour chaque programme.
Fonctions
Les différentes fonctions de lavage prévues par le lave-linge permettent dobtenir la propreté et le blanc souhaités.
Pour activer les fonctions:
1. appuyer sur la touche correspondant à la fonction désirée;
2. lallumage du voyant correspondant signale que la fonction est activée.
Remarque: Le clignotement rapide du voyant signale que la fonction correspondante nest pas disponible pour le
programme sélectionné.
Intensif
Grâce à l'utilisation d'une plus grande quantité d'eau au cours de la phase initiale du cycle et à l'emploi de
davantage de temps, cette fonction permet d'obtenir un lavage très performant.
Cette option nest pas activable avec les programmes 5, 6, 7, 11, 12, , , , .
Repassage facile
En cas de sélection de cette fonction, le lavage et lessorage seront dûment modifiés pour réduire le froissage.
Pour le programme 11 lappareil arrive au bout du cycle en laissant le linge tremper, le voyant de la fonction
REPASSAGE FACILE et celui de MARCHE/PAUSE se mettent à clignoter (orange), la phase RINCAGE reste
allumée en fixe. Pour vidanger leau et pouvoir sortir le linge, il faut appuyer sur la touche MARCHE/PAUSE ou sur
la touche REPASSAGE FACILE.
Cette option nest pas activable avec les programmes 5, 6, 7, 8, 9, 12, , , .
Rinçage plus
La sélection de cette fonction permet daugmenter lefficacité du rinçage et déliminer toute trace de lessive. Elle
est très utile en cas de peaux particulièrement sensibles.
Cette option nest pas activable avec les programmes 5, 6,
, , .
800-400
La sélection de cette fonction permet de réduire la vitesse d'essorage.
Cette option nest pas activable avec les programmes 11, .
Personnalisations
20
FR
Produits lessiviels et linge
Tiroir à produits lessiviels
Un bon résultat de lavage dépend aussi d'un bon
dosage de produit lessiviel: un excès de lessive ne
lave pas mieux, il incruste l'intérieur de votre lave-
linge et pollue l'environnement.
Sortez le tiroir à produits
lessiviels et versez la
lessive ou l'additif
comme suit.
bac 1: Lessive prélavage (en poudre)
bac 2: Lessive lavage (en poudre ou liquide)
En cas d'utilisation de lessive liquide, il est conseillé
d'introduire la boule doseuse directement dans la cuve.
bac 3: Additifs (adoucissant, etc.)
L'assouplissant ne doit pas déborder de la grille (max).
Le lave-linge prélève automatiquement lassouplissant
lors du dernier rinçage.
A la fin du programme de lavage il reste dans le bac 3
un résidu deau. Cette eau sert au prélèvement des
assouplissants très denses ou à dissoudre les
assouplissants concentrés. Si dans le bac 3 il reste un
peu plus deau que dhabitude, cela signifie que le
dispositif de vidange est bouché et empêche leffet
aspirant du dispositif.
bac 4: Eau de javel
Cycle blanchissage
Le blanchissage nest possible quavec les
programmes 2, 3, 7,
.
Verser le produit javelisé dans le bac 4, la lessive et
lassouplissant dans les bacs correspondants, puis
sélectionner un des programmes sus-indiqués.
Conseillé en cas de linge en coton très sale.
Triage du linge
Trier correctement le linge daprès:
- le type de textile / le symbole sur létiquette.
- les couleurs: séparer le linge coloré du blanc.
Vider les poches et contrôler les boutons.
Ne pas dépasser les valeurs indiquées
correspondant au poids de linge sec :
Textiles résistants: 5 kg max.
Textiles synthétiques: 2,5 kg max.
Textiles délicats: 2 kg max.
Laine: 1 kg max.
Combien pèse le linge ?
1 drap 400-500 g
1 taie doreiller 150-200 g
1 nappe 400-500 g
1 peignoir 900-1200 g
1 serviette éponge 150-250 g
Linge ou vêtements particuliers
Chemises: sélectionner le programme 10 approprié
au lavage de chemises de couleurs et textiles
différents. Il en prend le plus grand soin en réduisant
le froissage.
Soie: sélectionner le programme de lavage spécial 11
pour vêtements en soie. Il est conseillé dutiliser une
lessive spéciale pour linge délicat.
Rideaux: pliez-les bien et glissez-les dans une taie
d'oreiller ou dans un sac genre filet. Sélectionner le
programme 11.
Laine: Ariston est le seul lave-linge à avoir obtenu le
prestigieux label Woolmark Platinum Care (M.0508)
délivré par The Woolmark Company qui garantit le
lavage à la machine de tous les vêtements en laine, y
compris ceux qui portent létiquette lavage à la main
uniquement
. Grâce au programme 12 on peut
donc laver à la machine, en toute tranquillité, tous les
vêtements en laine (max. 1 kg) avec des performances
de lavage optimales.
Système déquilibrage de la charge
Avant tout essorage, pour éviter toute vibration
excessive et répartir le linge de façon uniforme, le
lave-linge fait tourner le tambour à une vitesse
légèrement supérieure à la vitesse de lavage. Si au
bout de plusieurs tentatives, la charge nest toujours
pas correctement équilibrée, lappareil procède à un
essorage à une vitesse inférieure à la vitesse
normalement prévue. En cas de déséquilibre excessif,
le lave-linge préfère procéder à la répartition du linge
plutôt quà son essorage. Pour une meilleure
répartition de la charge et un bon équilibrage, nous
conseillons de mélanger de grandes et petites pièces
de linge.
1 / 1

Indesit ARTL 82 (EX) Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi