Jenn-Air JDB3600AWX4 Guide d'installation

Marque: Jenn-Air

Modèle: JDB3600AWX4

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Ce manuel convient également à

JENN-AiR°

iNSTALLATiON iNSTRUCTiONS

UNDERCOUNTER DISHWASHER

iNSTRUCTiONS D'INSTALLATION

LAVE-VAISSELLESOUS PLAN DE TRAVAIL

Table of Contents ................................... 2

Table des matieres .................................. 26

W10282554A

Table of Confenfs

Dishwasher Safety ................................. 2

Installation Requirements ........................... 3

Tools and Parts ................................... 3

Location Requirements ............................ 4

Drain Requirements ............................... 6

Water Supply Requirements ........................ 6

Electrical Requirements ............................ 6

Installa6on Instructions ............................. 7

Prepare Cabinet Opening--Existing Utilities ........... 7

Prepare Cabinet Opening--New Utilities .............. 7

Prepare and Route Water Line ...................... 8

install Drain Hose ................................ 9

install Moisture Barrier (under a wood countertop) .... 11

Prepare Dishwasher ............................. 11

Make Power Supply Cord Connection ............... 12

Installation instructions (cont.)

Determine Cabinet Opening ....................... 14

install the Door Handle (on some models) ........... 14

Install Custom Panel ............................. 15

Choose Attachment Option ........................ 16

Move Dishwasher into Cabinet Opening ............. 17

Connect to Water Supply ......................... 19

Connect to Drain ................................ 20

Make Direct Wire Electrical Connection .............. 20

Secure Dishwasher in Cabinet Opening ............. 21

Bottom Sound Pad installation (on some models) ..... 23

Complete Installation ............................. 23

Check Operation ................................. 24

If Dishwasher Does Not Operate ................... 24

Additional Tips .................................. 24

DISHWASHERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

You Need to:

, Slowly open dishwasher door while someone grasps the

rear of the dishwasher. Remove shipping materials, drain

hose and lower rack. Close dishwasher door until latched.

, Observe all governing codes and ordinances.

, install this dishwasher as specified in these instructions.

, installation should be performed by a qualified service

technician. The dishwasher must be installed to meet all

electrical and plumbing national and local codes and

ordinances.

iNSTALLATiON REQUIREMENTS

Tools and Parts

Gather the recommended tools and parts before starting

installation. Read and follow the instructions provided with

any tools listed here.

All Installations

Tools needed:

P ers Flat-blade

I screwdriver _

5 iJ 1 ii

_A6 and ¼ _./_3 UL Listed or CSA

nut drivers or _y Approved twist-on 0

hex sockets _ wire connectors*

10" adjustable wrench_ %" onen-end

that opens to /_ wrench ,._J'_f

11/8"(2.9 cm) _.

If installing custom front panels,

Torx ®_T15 screwdriver

-Must be the proper size to connect vour household wiring

to 16-gauge wiring in dishwasher

Other useful items you may need:

F ash ight ,,__ i Bath towel _.._

Parts supplied:

Drain hose

clamps (2)

(1 large and

1 small)

Silver Green

Drain hose

#10 x 1/2''

sPchillips-head

rews (2)

2 - under-

counter

mounting

brackets (top)

Make sure all these parts are included in the literature package.

Parts needed:

3 3 " "

3A C0mprx ¼ Hose F_ttmg

FOrpart o[ kit, see local

retai!er or Call Whirlpoo!

Parts: t_800-442_9991. Part

4 #10 x 1/2"wood screws (if installing custom front panels)

Other parts you may also need:

11/2'!_2'' Masking or Moisture

(3,81_510 Cm) duct tape barrier tape ._

screw_type i I (Part Number_ /

damps

NOTE: Moisture barrier tape is recommended when installing a

dishwasher under a wood countertop.

NOTE: Parts available for purchase in plumbing supply stores.

Check local codes. Check existing electrical supply. See

"Electrical Requirements" section. It is recommended that

electrical connections be made by a licensed electrical installer.

In addition, for first=time installations

Tools needed:

Cordless drill

With 1/2,:3/4;

and 11/2 hole

saw bits

Parts needed:

Copper tubing (%'i See "Electrical Requirements" section

O.D. suggested) or ....

flexible braided E°rDirect Wire: For P0werSupp]y

water su_] • li_e use UL Listed/ Cord: use UL

CSA Certified listed power

_/------_-, strain relief to I supply cord kit

1 ))I fitTA (2i2 I PartNUmbe[ 4317824

hole marked for use

' With dishWaSher

Additional parts supplied with top-venting models only:

8 l 0w

Additional parts supplied with certain models only:

Bottom sound pad q

(located in lower rack) J

Make sure all these parts are included in the literature package.

If parts are not included, call 1-800-688-1100.

t® TORX is a registered trademark of Acument Intellectual Properties, LLC.

Location Requirements

Grounded electrical supply required.

Do not run drain lines, water lines or electrical wiring where

they can interfere with or contact dishwasher motor or legs.

The location where the dishwasher will be installed must

provide clearance between motor and flooring. Motor

should not touch the floor.

Do not install dishwasher over carpeted flooring.

Shelter dishwasher and water lines leading to dishwasher

against freezing. Damage from freezing is not covered by

the warranty.

A side panel kit is available from your dealer for installing

your dishwasher at the end of your cabinetry.

A moisture barrier accessory (Part Number 4396277) is

available from your dealer for installing underneath the

countertop. Call 1=800=688=1100 to order.

Check location where dishwasher will be installed. The

location must provide:

easy access to water, electricity and drain.

convenient access for loading and unloading dishes.

Corner locations require a 2" (5.1 cm) minimum

clearance between the side of the dishwasher door

and the wall or cabinet.

square opening for proper operation and appearance.

cabinet front perpendicular to floor.

level floor. (If floor at front of opening is not level with

floor at rear of opening, shims may be needed to level

dishwasher.)

Helpful Tip: Be sure to accurately measure dimensions

and ensure dishwasher is level if the floor in the

dishwasher opening is uneven (example: Flooring

extends only partway into opening).

NOTE: To avoid shifting during dishwasher operation,

shims must be securely attached to the floor.

If dishwasher will be left unused for a period of time or in a

location where it may be subject to freezing, have it

winterized by authorized service personnel.

Make sure pipes, wires and drain hose are within the

shaded area shown in the "Product and Cabinet

Opening Dimensions" section.

Product and Cabinet Opening Dimensions

*Insulation may be compressed

(not used on all models)

NOTE: Shaded areas of cabinet walls show where

utility connections may be installed.

*Measured from the lowest point on the

underside of countertop. May be reduced to

337/8" (86 cm) by removing wheels from

dishwasher.

**Minimum, measured from narrowest point of

opening.

Check that all surfaces have no protrusions

that would prohibit dishwasher installation.

Drain Requirements

. A new drain hose is supplied with your dishwasher.

If drain hose is not long enough, use a new drain hose

with a maximum length of 12' (3.7 m) (Part Number

3385556) that meets all current AHAM/IAPMO test

standards, is resistant to heat and detergent, and fits the

1" (2.5 cm) drain connector of the dishwasher.

Make sure to connect drain hose to waste tee or disposer

inlet above drain trap in house plumbing and 20"

(50.8 cm) minimum above the floor. It is recommended

that the drain hose either be looped up and securely

fastened to the underside of the counter, or be connected

to an air gap.

Make sure to use an air gap if the drain hose is connected

to house plumbing lower than 20" (50.8 cm) above

subfloor or floor.

Use 1/2"minimum I.D. drain line fittings.

If required, the air gap should be installed in accordance

with the air gap installation instructions. When you are

connecting the air gap a rubber hose (not provided) will

be needed to connect to the waste tee or disposer inlet.

Water Supply Requiremenfs

* A hot water line with 20-120 psi (138-862 kPa) water

pressure can be verified by a licensed plumber.

* 120°F (49°C) water at dishwasher.

* 3/8"O.D. copper tubing with compression fitting or

flexible braided water supply line (Part Number

4396897RP)

NOTE:1/2"minimum plastic tubing is not recommended.

* A 90° elbow with 3/4"Hose connection with rubber

washer

* Do not solder within 6" (15.2 cm) of the water inlet valve.

Eiecfrical Requiremenfs

Be sure that the electrical connection and wire size are

adequate and in conformance with the National Electrical

Code, ANSl/NFPA 70 - latest edition and all local codes and

ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

You must have:

120-volt, 60 Hz, AC-only, 15- or 20-amp, fused electrical

supply.

copper wire only.

We recommend:

a time-delay fuse or circuit breaker.

a separate circuit.

if connecting dishwasher

with a power supply cord:

Use UL listed power supply cord kit (Part Number

4317824) marked for use with dishwasher.

Power supply cord must plug into

a grounded 3 prong outlet, located in

the cabinet next to the dishwasher

opening. Outlet must meet all local

codes and ordinances.

if connecting dishwasher with direct wiring:

* Use flexible, armored

or nonmetallic

sheathed, copper wire

with grounding wire

that meets the wiring requirements for your home and

local codes and ordinances.

* Use a UL Listed!CSA Approved strain relief.

iNSTALLATiON iNSTRUCTiONS

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

I Dis_e box or circuk I

_al!ing dishwasher.

YeS'FollOw instructi0ns in the "PrePare cab!net

Opening_Existing Utilities!! section_

NO_FollowinstructionS n the-prepare Cabinet

Opening_New Uti!ities sectionl

_: E :isting hookups g t ity hookups

Water line

Prepare Cabinet OpeningmExisting

Utilities

If the water line and the cable extend to the locations

shown, proceed to the "Install Drain Hose" section. If they

do not reach far enough, follow the instructions in the

"Prepare Cabinet Opening--New Utilities" section.

Prepare Cabinet OpeningmNew

Utilities

Prepare and route the electrical supply

i i i_i

Option A, Power Supply Cord:

NOTE: A grounded 3 prong outlet is required inside a

cabinet next to the dishwasher cabinet opening.

Drill a 11/2"(3.8 cm) hole in cabinet side or rear.

See product and cabinet opening dimensions.

Woodcabinet:Sandtheholeuntilsmooth.

Metalcabinet:Coverholewithgrommetincludedwith

powersupplycordkit.

OptionB, Direct Wire:

Helpful "lip: Wiring the dishwasher will be easier if you

route the cable into the cabinet opening from the right-hand

side.

l_!JDirect Wire -- Drill hc

Optional location

Drill a %" (1.9 cm) hole in right-hand cabinet side or rear.

See product and cabinet opening dimensions.

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover hole with grommet (Part Number

302797 - not provided).

Route cable from power supply through cabinet hole (cable

must extend to the right front side of cabinet opening).

Tape cable to the floor in area shown. This will prohibit

cable from moving when dishwasher is moved into

cabinet opening.

Prepare and Route Wafer Line

Helpful Tip: Routing the water line through the left side

of cabinet opening will make water connection easier.

Drill hole

Preferred locations

Drill a V2"(1.3 cm) hole in the cabinet side or rear.

Measure overall length of copper tubing or flexible

braided water supply line. Attach to the hot water line

using a connection configuration that is in compliance

with local codes and ordinances. The water line to the

dishwasher should have a manual shutoff valve.

Slowlyroutewatersupplylinethroughholeincabinet.

(Ifusingcoppertubing,itwillbendandkinkeasily,sobe

gentle.)Itshouldbefarenoughintothecabinetopening

toconnectittothedishwasherinletonthefrontleft

sideofthedishwasher.

Slowlyturnwatershutoffvalveto "ON"position.Flush

waterintoashallowpanuntilcleartogetridofparticles

thatcouldclogtheinletvalve.Turnshutoffvalveto

"OFF"position.

Coppertubingonly:Slidenut,thenferrule,about1"

(2.5cm)ontocoppertubing.

NOTE:Toavoidvibrationduringoperation,routethe

watersupplylinesothatitdoesnottouchthe

dishwasherbase,frameormotor.

t® Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.

-:J water supply line

Connect the 3/8"compression fitting to the water supply

line prior to installing the unit into the cabinet opening.

Attach such that the 3/4"connection is facing upward.

Copper tubing only: Put the tubing into the 90 ° elbow

fitting as far as it will go (the copper tubing bends and

kinks easily). Slide the nut and ferrule forward and start

the nut onto the elbow threads.

Flexible braided connection: Secure nut to elbow using

%" open ended wrench or adjustable wrench.

NOTE: Do not use Teflon ®* tape with compression

fitti ngs.

Install Drain Hose

iMPORTANT: Always use a new drain hose. Check local

codes to determine if an air gap is required.

If needed, drill a 11/2"(3.8 cm) diameter hole in cabinet wall

or side of the opening closest to the sink.

Route drain hose as shown through hole in cabinet to the

front center of opening where drain connection will be

made. Tape drain hose to the floor in area shown. This will

prohibit it from moving when dishwasher is moved into

cabinet opening. 9

Connectdrainhosetowasteteeorwastedisposer

usingoneofthefolowingoptions:

•OptionA,Wastedisposer- noairgap

•OptionB,Nowastedisposer-noairgap

-OptionC,Wastedisposer-withairgap

-OptionD,Nowastedisposer-withairgap

IMPORTANT: The drain hose connection of the disposer or

a waste tee must be made before the drain trap and at

least 20" (50.8 cm) above the floor where the dishwasher

wil be installed.

Helpful Tip: To reduce vibration of the hose, keep the hose

away from the floor.

Option A, Waste disposer - no air gap

1. Using a hammer and screwdriver,

knock plug into disposer.

2. Use needle-nose pliers to remove

plug.

3. Attach drain hose to disposer inlet

with large silver drain hose clamp

(provided). Use pliers to squeeze

clamp open and move into position.

Option B, No waste disposer - no air gap

1. Connect black end of of drain hose to

waste tee and cut if needed.

(Do not cut ribbed section.)

2. Attach black end of drain hose to waste

tee with a large silver drain hose clamp

(provided). Use pliers to squeeze clamp

open and move into position. If the drain

hose was cut, use a 1W' to 2" (3.8 to

5 cm) screw-type clamp (not provided).

Option C, Waste disposer - with air gap

Drain trap

1. Using a hammer and screwdriver,

knock plug into disposer.

2. Use needle-nose pliers to remove

plug.

3. Connect black end of drain hose to air

gap and cut if needed. (Do not cut

ribbed section.)

Attach drain hose to air gap with large

silver drain hose clamp (provided).

Use pliers to squeeze clamp open and

move into position. If the drain hose

was cut, use a 11/2'' to 2" (3.8 to

5 cm) screw-type clamp (not

provided).

Use a rubber hose (not provided) with

screw-type clamps (not provided) to

connect from air gap to disposer inlet.

Option D, No waste disposer - with air gap

....... Drab

Connect black end of drain hose to air

gap and cut if needed. (Do not cut

ribbed section.)

Attach drain hose to air gap with large

silver drain hose clamp (provided).

Use pliers to squeeze clamp open and

move into position. If the drain hose

was cut, use a 11_"to 2"(3.8 to 5 cm)

screw-type clamp (not provided).

Use a rubber hose (not provided) with

screw-type clamps (not provided) to

connect from waste tee to air gap.

Insfall Moisfure Barrier

(undera wood counterfop)

Install moisture barrier

(under a wood countertop)

Moisture

barrier

1. Make sure the area under the cabinet is clean and dry

for installation of the moisture barrier.

2. Remove the backing of the moisture barrier and apply

to underside of the countertop along the front edge of

the counter.

7;iiii_;iiii_;iiii_i_i_i;ii_:ii_7i_:ii_7i_:ii_7i_7_i:i7_7_i_i_i_`_i_i_i_`_i_i_7ii_i_i:ii_7i_:ii_7i_:ii_i1i_i1i_7i_i1i1_i_i_¸i,,,,;'ii,i;'ii,;,;,;,il_i;_;i_;i,i;'iii_;i_;_i;'iii_;i_;_i;'iii_;i_;_i;'iii_;i_;_i;'iii_;i_;_i;'ii,;,i;'ii,;,i;'ii,;,i;'ii'iii';'ii'iii'ii,;,;,i;'iii_;i_;_i;`_;_;_;_;_;_;_;_;_:_;_;_:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;:_;_:;::_

Prepare Dishwasher

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Helpful Tip: Place cardboard under dishwasher until installed

in cabinet opening to avoid damaging floor covering. Do not

use door panel as a work table without first covering with a

towel to avoid scratching the door panel.

Using two or more people, grasp sides of dishwasher door

frame and place dishwasher on its back.

Using a V4" hex head socket, nut driver or Phillips

screwdriver, remove two screws attaching access panel

and lower panel to dishwasher. Do not remove tech

sheet from access panel.

Using a 1/4" hex head socket, nut driver or Phillips

screwdriver, remove terminal box cover. Retain for

later use.

Install a UL Listed/CSA Certified strain relief. Make sure

screwheads are facing to the left when tightening conduit

nut. Strain relief is provided with the power supply cord kit.

connection will you use? I

Make Power Supply Cord Connection

Option A, Power Supply Cord:

Route cord so that it does not touch dishwasher motor

to lower part of dishwasher tub. Pull cord through strain

relief in terminal bow. Take notice when installing or

removing the dishwasher in order to reduce the chance

of damaging the power supply cord.

Select UL Listed/CSA Certified twist-on wire connectors

(included with power supply cord kit) rated to connect

your power supply cord to 16-gauge dishwasher wiring.

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector

in terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

Power Supply Cord--

Connect ground wire

II --G

Remove the green grounding screw and place through

the ring terminal of the green ground wire. Reattach and

tighten the green screw.

NOTE: Twist on wire connector. Gently tug on wires to

be sure both are secured.

Connect wires black to black and white to white, using

UL Listed!CSA Certified twist-on wire connectors

(included with power supply cord kit).

wh te _white

ground wire_ ground connector

If needed, see website for animated representation of

this step. Visit www.jenn-air.eom under FAQ tab.

Tighten strain relief screws to secure cord.

Place wires inside terminal box. Insert tabs on left side

of cover. Make sure wires are tucked inside box. Close

cover ensuring wires are not pinched. Use 1/4"nut driver

and previously removed screw to secure cover.

NOTE: Do not plug into outlet until instructed to do so.

iiiiiiiiiiiiiii_iiiiii_iiiiiiil¸il¸i_iYii_iiii_iii_iiiiiii1itii1iiii_i_i_ii_i_ii_i_ii_i_ii_i_i_i_i_i_ii_ii_i_ii_i_i_I_ii_ii_I_i_i_}1iiiiiiii_i_ii_i_i11iii!!iiiiiiii1i11ii1i1ii1i1%i1iiii%1i11tiiiii_i1iiiiiiii_i_¸il¸ii'iii_ii_i_ii'ii_ii_}iiiiiiiiil¸il¸ii_ii_ii_i_iiiiiiiiiiiiii_iii:`i_`_ii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii1i111iiiiii11iiiii1tiii_iiiii1_i1iii_iiiiiii_,_iiiiiii_,_iiiiiii_,_iiiiiii_,_iiiiiii_,_iiiiiii_,_iiiiiiiiiiiiiiiii_i_i_iiiiiii

Determine Cabinet Opening

Measure height of cabinet opening from underside of

countertop to floor where dishwasher will be installed

(you will need to measure the lowest point on the

underside of the countertop and the highest point on the

floor). Refer to "Dishwasher Height Adjustment Chart"

for wheel position and the number of turns needed.

| I

CaM net, Whee! Numbe[ 0t:turns

opening height poSition on front leg

7 remO_e AI! the way up33% (86.0 cm)

34"/S614Cm)1 10

NOTE: If the minimum cabinet opemng height is less than

34" (86.4 cm), the rear wheels can be removed for

additional clearance. This will allow the dishwasher to fit

into a 337/8.' (86 cm) high cabinet opening, but the

dishwasher will be more difficult to move. (Measurements

are approximate. Wheels and legs are preset at the

factory for 341/2.' [87.6 cm].)

wheel

Turn both leveler legs to the same height. Put wheels in

the required position determined from "Dishwasher

Height Adjustment Chart."

)

Built-up floors (Kitchen floor height is higher than

cabinet opening.) Example: Kitchen floor tile does not

extend into cabinet opening. Add shims as needed in the

area shown to bring the dishwasher up to 34" (86.4 cm)

below the countertop.

NOTE: Shims must be securely attached to floor to avoid

movement when the dishwasher is in use.

Install the Door Handle

(on some models)

IMPORTANT:Donotscratchthefrontpanelduringthis

procedure.

Removethedoorhandleandhardwarebagcontaining

thesetscrewsandAllenwrenchfromthecardboardbox.

Setscrewsarealreadyinstalledinthehandle.Place

handleonmountingstudswiththesetscrewsfacing

down.Pushthedoorhandletightlyagainstthedoor.

InserttheshortendoftheAllenwrenchintothe

setscrews.Tightenthesetscrews1/4turnpastsnug.

RetainAllenwrenchwithInstallationInstructions.

Install Custom Panel

(Model JDB3600AWX)

NOTE: The handle for the custom panel is not included.

IMPORTANT: If the handle is attached from the back of

the custom panel, the screw holes should be countersunk

for the screws heads to be flush with the panel. If the

handle is attached to the front of the custom panel, the

screw lengths cannot exceed the panel thickness. For

more information on Jenn-Air ®custom handle selection,

refer to the Jenn-Air ®Catalog, visit www.jenn-air.com, or

call 1-800-688-1100.

NOTE: A customer-supplied full front panel must weigh

no more than 16 Ibs (7.3 kg) and must be made to

specific dimensions. It is recommended that a

cabinetmaker cut the custom panel because of the

precise dimensions needed.

NOTE: All mounting hardware supplied is for a 3/4"

(19.1 mm) thick wood panel. If a thinner wood panel, or

materials other than wood are used, it is the customer's

responsibility to obtain the proper length screws and

adjust the pilot holes accordingly.

IMPORTANT: Use a moisture-resistant sealer on both

sides and all edges of the panel to avoid damage from

humidity.

-:JDish . ash.erswith control !

panel on the top ......

231/2" __3

(59.7 cm) oaA_'' (76.7 cm)

(19.1 mm)

*This dimension is for 4" (10.2 cm) toe kick. If the

installation needs a higher toe kick, adjust the height

of the wood panel accordingly. Not recommended for

toe kicks greater than 6" (15.2 cm).

With a TORX screwdriver, remove three screws from both

sides, as shown; hold the outer panel up while removing

the screws. Save screws for reinstallation.

Custom panel dimensions--

Dishwashers with control panel

on the top

.....i

3 screws

per side

outer [

Gently set outer panel aside. Lay the customer-supplied

custom panel face down on a covered, non-scratching

surface.

929/32 H

(25.2 cm)

p edge

Measure 92%2"(25.2 cm) from top edge and mark a line on

the back of customer-supplied custom panel. Position the

outer panel on the back of the customer-supplied custom

panel as shown, so that the top holes in the outer panel are

on the line, and both panels are centered side to side.

Mark pilot

holes

Mark all four hole locations; remove outer panel. Drill %2"

pilot holes 1/2"(13 mm) deep in customer-supplied custom

panel. Place the outer panel on the back of the customer-

supplied custom panel; align holes.

_;51_ _¸¸¸ _

Attach outer panel to back of customer-supplied custom

panel with the four #10-16 x %" hex head screws supplied

in the literature package. Attach the handle. The handle

should be centered on the front of the customer-supplied

custom panel in the area shown.

iMPORTANT: Screw heads must be flush with back of

customer-supplied custom panel.

R edges

3 screws

each side Customer-supplied

panel

Attach the panel assembly to the door by reinstalling the

three screws on each side; do not tighten completely. This

reinstallation of the three screws will hold the panel

assembly in place on the door frame,

top

edges

Drill through

these holes

Customer-supplied

panel

Align the top edge of the customer-supplied custom

panel with the top of the console.

Drill two %2" pilot holes 1/2"(13 mm) deep, into the

customer-supplied custom panel, through the holes in the

top corners on the inner panel, as shown.

top

edges

)rill through

these holes

Customer-supplied

panel

Install the two #8-18 x 1%" screws from

the literature package in the top corners of the inner

panel. Tighten the six side screws reinstalled in Step 6.

Choose Affechmenf Opfion

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Using 2 or more people, stand the dishwasher up.

Option 1, Countertop attachment:

11_,Remove bracket

Tabs must point

_s I ,%_ to the right

() :

Remove the brackets from the package and place in the

open slots on the left and right-hand top of the

dishwasher collar as shown.

Insert the bracket into the slot on the collar. Using a pair

of pliers, bend the tab down to secure the bracket in

place. Repeat this step for the other side.

NOTE: Do not attach the dishwasher. This will be done

later.

Option2,Dishwasher side attachment:

NOTE: Remove the brackets from the parts package.

Break off the end of the bracket along the scored line.

With another person holding the rear of the dishwasher

to keep it from tipping, open dishwasher door and place

towel over pump assembly and spray arm of dishwasher.

This will keep screws from falling into pump area when

you are securing dishwasher to cabinet.

Push the plastic buttons out of the side of the tub.

NOTE: Save the buttons to cover the holes after

dishwasher is installed.

3_31Reinstall bracket

bend

tabs _/

Push bracket into slot on the side of dishwasher, and

bend tab in toward the side of the dishwasher so that it

keeps the bracket in place. Repeat this step for the other

side of the dishwasher.

NOTE: Do not attach the dishwasher. This will be done

later.

Move Dishwasher info Cabinet

Opening

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

1J Stand dishwasher upright

Using two or more people, stand dishwasher upright.

NOTE: Do not install kickplate until instructed to do so.

IMPORTANT: Double-check correct placement of utilities.

Grasp the sides of the dishwasher at the edges of the

door panel. Tilt dishwasher backward on wheels and

move dishwasher close to cabinet opening.

NOTE: Do not push on the front of the panel or on the

console. Panel or console may dent.

Helpful Tip: Temporarily tape utilities to the floor in the

locations shown to prohibit them from moving when

dishwasher is moved into the cabinet opening.

Checkthatwaterlineisontheleftsideofopeningand

drainhoseisnearthecenterofthecabinetopening.

Withanotherpersonholdingthedishwashertoavoidit

fromtipping,openandclosethedoorafewtimes.Ifthe

doorclosesorfallsopenunderitsownweight,thedoor

tensionwillneedtobeadjusted.

Toadjustthedoorspringtension,unhookthespring

fromtherearlegofdishwasher.

UsingasA6"nutdriverorhexsocket,removethescrew

fromthetensioner.

ThescrewcanbeputintooneofthreeholesIBiI_1,1_1

in the front leg of dishwasher. If the door closes by itself,

move the tensioner to a higher number hole and replace

screw. Reattach door spring to rear leg.

NOTE: Tensioners on both sides of dishwasher should be

secured at same holes.

When door is unlatched, and door opens by itself, move

the tensioner to a lower numbered hole and replace the

screw. Reattach door spring to rear leg.

NOTE: Tensioners on both sides of dishwasher should

be secured at same holes.

IMPORTANT: If wheels were removed, avoid damage to

the floor when moving the dishwasher. Slowly move

dishwasher completely into cabinet opening. Do not kink

or pinch water line, drain hose, power supply cord or

direct wire between dishwasher and cabinet. Remove

cardboard from under dishwasher.

NOTE: It is all right if dishwasher fits tightly into cabinet

opening. Do not remove insulation blanket-the blanket

reduces the sound level.

NOTE: If using power cord, make sure to route end

through hole in cutout before sliding dishwasher into

cabinet opening.

Align front of dishwasher door panel with front of

cabinet doors. You may need to adjust alignment to be

even with your cabinets.

Checkthatlevelinglegsarefirmlyagainstthefloor.

Closeandlatchthedoor,andplacelevelagainstthe

frontpanel.Checkthatdishwasheriscenteredfromfront

tobackintheopening.Ifneeded,adjustlevelingleguntil

dishwasherisplumb.Repeatforothersideofdishwasher.

Helpful Tip: Push up on front of dishwasher to raise

dishwasher off the ground to adjust front legs. With

some installations, it may be easier to adjust the front leg

using the 3/16"hex head socket or adjustable wrench.

Place level against top front opening of tub. Check that

dishwasher is level from side to side. If dishwasher is not

level, adjust front legs up or down until dishwasher is

level.

Be sure rubber washer is properly seated in fitting. Slide

the 3/4"fitting up to the valve and hand tighten to avoid

cross-threading. Hand tighten until the coupling is tight.

Using pliers, check the tightness of the coupling. An

additional 1/4to 1_turn may be required to seal the rubber

gasket.

NOTE: Do not overtighten. Damage to the coupling can

result.

Place paper towel under 90 ° elbow fitting. Turn on water

supply and check for leaks. If leak occurs, repeat

previous step.

If needed, see website for animated representation

of this step. Visit www.jenn-air.com/watersupply under

FAQ tab.

iiii;ii_il;ii_il;iiiiiiiiiiiiiii;i;ii_ii_ii_i_i_ii_ii_i_ii_ii_i_ii_i_ii_;iii_ii_ii_;;iii_ii_;;iii_ii_;;iii_i_ii_;iiii_,iliiiiiiiiiiiiiiii_'_i¸ii_'_i¸ii_'_'_iii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii¸i_iiii!_i;:i;:i;):0:_i;:i;):0:_i;:i;):0:_i;:i;):0_i;:ii:;:i;:ii:;:i;:i;):0:_ii_:0:_iiiiii1iiiiiiiiiiii_;iiiiiiii_iiiiiiiiiiiiIiIi_i¸i_i¸i_i¸i_ii_i¸i_i¸i_i¸i_ii_i¸i_i¸i_i¸i_ii_i¸i_i¸i_i¸i_ii_i¸i_i¸i_i¸i_ii_i¸i_i¸i_i¸i_ii_i¸i_i¸i_i¸i_ii_i¸i_i¸i_i¸i_ii_i¸i_i¸i_i¸i_ii_i¸i_i¸i_i¸i_ii_i¸i_i¸i_i¸i_ii_i¸i_i¸i_i¸i_ii_i¸i_i¸i_i¸i_ii_i¸i_i¸i_i¸i_ii_i¸i_i¸i_i¸i_iiiii'i_iiiiiiiiiiiiii

Connect to Drain

Place towel under drain hose to catch any water in drain

hose. Place the small green drain hose clamp onto the

small end of the drain hose. Push the new drain hose

into the black drain hose connector up to the drain hose

stop.

Using pliers, squeeze open the small green drain hose

clamp and slide onto connector between stops.

After hose is connected, remove towel.

If needed, see website for animated representation of

this step. Visit www.jenn-air.com/drain under FAQ tab.

Make DirectWire Electrical