Simplicity 021019-00 Manuel utilisateur
- Catégorie
- Nettoyeurs haute pression
- Taper
- Manuel utilisateur
Manual No. 80077234 Rev B
Pressure Washer
Operator’s Manual
Model Number _____________________________
Revision __________________________________
Serial Number ______________________________
Date Purchased ____________________________
Copyright © 2020. Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
Oregon® is a registered trademark of Blount, Inc. in the United States and
other countries. Used under license.
(833) 871-4330
www.oregonproducts.com
2 www.oregonproducts.com
Table of Contents
Symbols and Meanings ...........................2
Equipment Description............................3
Features and Controls ............................4
Operation.......................................6
Maintenance ...................................10
Storage .......................................11
Troubleshooting ................................12
Warranty ......................................13
Register Your Product
To ensure prompt and complete warranty coverage, register
your product online at www.onlineproductregistration.com.
Symbols and Meanings
Signal Meaning
DANGER
Indicates a hazard which, if not avoided,
will result in death or serious injury.
WARNING
Indicates a hazard which, if not avoided,
could result in death or serious injury.
CAUTION
Indicates a hazard which, if not avoided,
could result in minor or moderate injury.
NOTICE
Indicates information considered
important, but not hazard-related.
Symbol Name Explanation
Safety Alert
Symbol
Indicates a potential personal
injury hazard.
Read
Operator’s
Manual
Failure to follow warnings,
instructions and operator’s
manual could result in death or
serious injury.
Toxic
Fumes
Engine exhaust contains carbon
monoxide, a poisonous gas that
could kill you in minutes. You
cannot smell it or see it.
Fire
Fuel and its vapors are
extremely ammable which
could cause burns or re
resulting in death or serious
injury.
Engine exhaust could cause
re resulting in death or serious
injury.
Symbol Name Explanation
Fluid
Injection
High-pressure water could cut
through skin resulting in serious
injury and possible amputation.
Spray,
Flying
Objects
Risk of eye injury. Spray could
splash back or propel objects
resulting in serious injury.
Hot Surface
Contact with muer area could
cause burns resulting in serious
injury.
Electric
Shock
Contact with power source
could cause electrical shock
resulting in death or serious
injury.
Kickback
Recoil starter kickback will pull
hand and arm toward engine
faster than you can let go which
could cause broken bones,
sprains or bruises resulting in
serious injury.
Chemical
Burn
Chemicals could cause burns
resulting in death or serious
injury.
Slippery
Surface/Fall
Slippery wet surfaces could
cause you to fall resulting in
death or serious injury.
Fall
Kickback from spray gun could
cause you to fall resulting in
death or serious injury.
WARNING! This product can expose you to
chemicals including gasoline engine exhaust,
which is known to the State of California to cause
cancer, and carbon monoxide, which is known to the State of
California to cause birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov.
WARNING! This product contains lead and lead
compounds, known to the state of California to
cause birth defects or other reproductive harm.
Wash your hands after handling this product. Cancer and
Reproductive Harm - www.P65Warnings.ca.gov.
3
High Pressure Hose — Connect one end to water pump
and the other end to spray gun.
High Pressure Outlet — Connection for high pressure
hose.
Identication Label — Provides model and serial number of
pressure washer.
Pump — Stainless steel piston, axial cam pump that
develops high pressure.
Water Inlet — Connection for garden hose.
Equipment Description
Read this manual carefully and become familiar
with your product. Know its applications, its
limitations, and any hazards involved. Save these
original instructions for future reference.
To aid in outdoor cleaning projects, this engine-driven,
high-pressure cleaning machine uses a variety of spray
tips and detergent.
Know how to stop the product and reduce pressure
quickly. Keep operating area clear and do not allow
children to operate pressure washer.
Stay alert—watch what you are doing. Do not operate
pressure washer when fatigued or under the inuence of
alcohol or drugs.
Every eort has been made to ensure that information in
this manual is accurate and current. However, we reserve
the right to change, alter, or otherwise improve the product
and this document at any time without prior notice.
NOTICE If you have questions about intended use,
contact an authorized service dealer. This equipment is
designed to be used with Briggs & Stratton
®
authorized
parts only.
For engine related questions, call American Honda
Motor Company, Inc. at (800) 426-7701 or visit
www.honda-engines.com for a dealer locator.
This spark ignition system complies with the Canadian
standard ICES-002.
High Pressure Outlet
Water Inlet
High Pressure Hose
Identication Label
Pump
4 www.oregonproducts.com
Features and Controls
Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and
product warnings.
5
Automatic Cool Down System — Prevents
internal pump damage by discharging warm
water to the ground.
Detergent Siphon Tube — Use to siphon
pressure washer safe detergent into the low
pressure stream.
Spray Wand — Allows you to switch between
spray tips.
Spray Gun — Controls spray using trigger.
Includes trigger lock.
Spray Tips — Multiple patterns for various
cleaning applications.
Spray Tips
Spray Wand
Spray Gun
Automatic Cool Down
System (on pump)
Detergent Siphon Tube
6 www.oregonproducts.com
Operation
Step 1: Safe Location
Before starting the pressure washer, there are two equally
important safety concerns regarding carbon monoxide
poisoning and re that must be addressed.
Operation Location to Reduce the Risk of Carbon
Monoxide Poisoning
The engine exhaust of all fossil fuel burning equipment,
such as a pressure washer, contains carbon monoxide, a
poisonous gas that could kill you in minutes. You cannot
smell it, see it, or taste it. Even if you do not smell exhaust
fumes, you could still be exposed to carbon monoxide gas.
By law, it is required in many states to have a carbon
monoxide alarm in operating condition in your home. A
carbon monoxide alarm is an electronic device that detects
hazardous levels of carbon monoxide. When there is
a buildup of carbon monoxide, the alarm will alert the
occupants by ashing a visual indicator light and an alarm.
Smoke alarms cannot detect carbon monoxide gas.
WARNING! Engine exhaust contains carbon
monoxide, a poisonous gas that could kill you in
minutes. You cannot smell it, see it, or taste it.
Even if you do not smell exhaust fumes, you could still be
exposed to carbon monoxide gas.
• Operate this product only outdoors, far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas accumulating and the potential of being
drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
• Do not run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors and
windows for ventilation. Carbon monoxide can quickly
build up in these spaces and can linger for hours, even
after this product has shut o.
• Point exhaust away from all homes and occupied
spaces.
• If you start to feel sick, dizzy, or weak while using this
product, get to fresh air right away. See a doctor. You
may have carbon monoxide poisoning.
Carbon monoxide alarm
7
Operation Location to Reduce the Risk of Fire
WARNING! Exhaust heat/gases could ignite
combustibles, structures or damage fuel tank
causing a re, resulting in death or serious injury.
• Pressure washer must be at least 5 ft. (1.5 m) from any
structure, overhang, trees, windows, doors, and any wall
opening, shrubs, or vegetation over 12 in. (30.5 cm) in
height.
• Do not place pressure washer under a deck or other type
of structure that may conne airow. Smoke alarm(s)
must be installed and maintained indoors according to
the manufacturer’s instructions /recommendations.
• Carbon monoxide alarms cannot detect smoke.
• It is a violation of California Public Resource Code
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as
dened in Section 4442, maintained in eective working
order. Other states or federal jurisdictions may have
similar laws, reference Federal Regulation 36 CFR Part
261.52.
• Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
• Replacement parts must be the same and installed in the
same position as the original parts.
Step 2: Oil and Fuel
Check Oil Level
1. Make sure pressure washer is on a level surface.
2. Refer to engine operator’s manual and follow oil and
fuel recommendations and instructions.
Transporting
Do not tip engine or equipment at an angle which causes
fuel to spill.
Step 3: Set Up
Clean Debris
Clean any accumulated debris. Keep area around muer
free from any debris.
• Use a soft bristle brush to loosen caked on dirt or oil.
• Use a damp cloth to wipe exterior surfaces clean.
Lubricate O-rings
Lubricate all connections shown to extend the life of the
o-rings.
1. Inspect and clean connecting surfaces prior to
lubrication and assembly. Replace o-rings that are
damaged or missing. See Common Service Parts.
NOTICE Never repair leaking connections with sealant of
any kind. Replace o-ring.
2. Use a small brush or cotton swab to apply a light
coating of grease directly to o-rings.
5 ft (1.5 m)
min.
5 ft (1.5 m) min.
Spray Gun
High
Pressure
Hose
Spray Wand
8 www.oregonproducts.com
Check / Connect Gun and Hose
1. If spray gun trigger depresses without pressing
trigger lock or if spray gun remains depressed when
released, replace spray gun immediately.
2. If high pressure hose is damaged, exposing inner
mesh, replace immediately.
3. Attach high pressure hose to spray gun and high
pressure outlet on pump. Tighten by hand.
WARNING! The high pressure uid could cut
through skin and its underlying tissues, resulting
in serious injury and possible amputation. Never
attach spray wand directly to high pressure hose.
Check Water Inlet Screen / Connect Garden Hose
1. Inspect inlet screen. Remove debris or replace if
damaged.
2. Run water through garden hose (not to exceed 50 ft
(15 m) to clean out debris, then connect to water inlet.
NOTICE There must be at least 10 ft (3 m) of
unrestricted garden hose between the pressure washer
inlet and any device, such as a vacuum breaker, to
prevent pump damage.
3. Turn on water, point spray gun in safe direction, press
trigger lock and depress trigger to purge pump system
of air.
4. Attach spray wand to spray gun. Tighten by hand.
Step 4: Spray Tips
1. Select desired spray tip:
Low Pressure
Black Soap
Use to apply
detergent
Delicate Rinse
White, 40°
Green, 25°
Cars / Vans
/ Trucks /
Outdoor
Furniture
General Rinse
Yellow, 15°
Siding /
Patios Decks
Driveways /
Garage Floors
Maximum
Rinse
Red, 0°
Paint Removal
/ Oil Stains
/ Rust Removal
2. Pull spray wand quick connect collar back, insert
spray tip and release. Tug spray tip to ensure it is
secure.
Step 5: Start Up
NOTICE Do not start engine without water supply
connected and turned on.
1. Level product before starting.
WARNING! Risk of eye injury. Spray could
splash back or propel objects, resulting in
serious injury.
• Always wear indirect vented (chemical splash) safety
goggles when using or near this product. (Safety glasses
do not provide full protection).
• Always wear protective clothing such as long-sleeved
shirts, long pants and closed-toed shoes.
Inlet Screen
Trigger Lock
9
WARNING! Recoil starter kickback (rapid
retraction) will pull hand and arm toward engine
faster than you can let go, which could cause
broken bones, fractures, bruises, or sprains and result in
serious injury.
2. Position yourself as shown below, and start engine
according to instructions given in engine operator’s
manual.
WARNING! High-pressure water could cut
through skin resulting in serious injury and
possible amputation.
• Do not direct discharge at self or others.
• Call physician immediately if cut by uid. Do not treat as
a simple cut.
• Do not touch spray tips while spraying.
WARNING! Use of pressure washer
could create slippery surfaces causing
you to fall, resulting in death or serious
injury. Kickback from spray gun could cause you to fall
resulting in death or serious injury. Operate pressure
washer from a stable surface.
3. Firmly grasp spray gun with both hands, point spray
gun in safe direction, press trigger lock and depress
trigger to begin spraying.
4. Apply high pressure spray to a small area rst, then
check the surface for damage. If no damage is found,
it is okay to continue cleaning.
WARNING! Risk of electrocution. Contact with
power source could cause electric shock or burn
resulting in death or serious injury. Never spray
near power source.
Usage Tips
• For most eective cleaning, keep spray tip 8 to 24 in (20
to 61 cm) away from cleaning surface.
• Do not use high pressure spray tips closer than 6 in (15
cm) to prevent damage to the cleaning surface.
• Start at the top of the area to be rinsed, working down
with long, even, overlapping strokes.
Step 6: Applying Detergent
WARNING! Chemicals could cause burns
resulting in death or serious injury.
• Follow chemical manufacturer’s label instructions for
proper use and handling of the chemical.
• Only use products marketed for use with pressure
washers.
• Never spray acids or ammable liquids.
Check Detergent Siphoning Tube
Clean detergent tube if clogged or replace if leaking.
To apply detergent, follow these steps:
1. Attach detergent siphon tube to the barbed fitting on
the pump.
2. Prepare detergent per pressure washer detergent
manufacturer’s instructions.
3. Insert detergent siphon tube into pressure washer
detergent.
4. Install black detergent spray tip. See Spray Tips.
5. Apply per manufacturer’s instructions.
NOTICE Detergent cannot be applied with the high
pressure spray tips (White, Green, Yellow or Red).
10 www.oregonproducts.com
Step 7: Shut Down
1. Release spray gun trigger and let engine idle for one
minute.
2. Turn engine o according to instructions given in
engine operator’s manual.
WARNING! Spray gun traps high water
pressure, even after engine shut down and water
disconnection, which could result in serious
injury.
3. Point spray gun in safe direction. Press trigger lock
and depress trigger to relieve high water pressure.
Step 8: Clean Up
1. Turn o water and purge system.
2. Disconnect and drain all hoses, spray gun and spray
wand.
3. Empty pump of all liquids by pulling recoil handle
about six times.
NOTICE If storing in freezing temperatures or more than
30 days, see Storage.
Maintenance
Maintenance Schedule
Follow the hourly or calendar intervals, whichever occurs
rst. See the engine operator’s manual for instructions on
how to properly maintain the engine.
General Recommendations
Regular maintenance will improve the performance and
extend the life of the pressure washer. See any authorized
dealer for service.
Pump Oil
Do not attempt any oil maintenance on this pump. The
pump is pre-lubricated and sealed from the factory,
requiring no additional maintenance for the life of the
pump.
Detergent Siphoning Check Ball
The check ball in detergent siphoning system may become
stuck from dried soap or minerals in water. The check ball
can be freed by performing the following:
WARNING! Chemical Burn Hazard. Chemicals
could cause burns resulting in death or serious
injury. Follow chemical manufacturer’s label
instructions for proper use and handling of the chemical.
Following Shut Down, remove detergent siphoning hose
from barbed tting on pump.
1. Insert paper clip, or similar device, into barbed tting
on pump and push down until ball moves.
2. Reinstall detergent siphoning hose.
Spray Tip Maintenance
Clean an obstructed spray tip to correct a pulsing
sensation when squeezing the spray gun trigger.
1. Following Shut Down, remove spray tip from spray
wand.
2. Use a paper clip, or similar device, to free foreign
material.
Engine Maintenance
See the engine operator’s manual for instructions on how
to properly maintain the engine.
Common Service Parts
Pump Saver™ ............................6039
O-ring Maintenance Kit ...................705001
Water Inlet Screen ..................... B2384GS
Engine Oil Bottle ...............100005 or 100028
Contact an authorized service dealer or
BRIGGSandSTRATTON.COM for a full list of parts and
diagrams.
Every 8 Hours or Daily (see Operation Section)
Check engine oil level
Clean debris
Lubricate o-rings
Check spray gun
Check high pressure hose
Check / clean water inlet screen
Check detergent siphoning tube
11
Storage
WARNING! Fuel and its vapors are extremely
ammable, which could cause burns or re,
resulting in death or serious injury. Do not store
fuel near ignition source.
1. Place detergent siphon tube in water and ush
detergent from system by running pressure washer
with black spray tip.
Protecting Fuel System
2. Treat or drain fuel from pressure washer as fuel can
become stale when stored over 30 days.
Each time you ll the container with fuel, add STA-BIL
360°® PROTECTION™ to the fuel as specied by the
manufacturer’s instructions. This keeps fuel fresh and
decreases fuel-related problems or contamination in the
fuel system.
It is not necessary to drain fuel from the engine when STA-
BIL 360°® PROTECTION™ is added as instructed. Before
storage, turn the engine ON for 2 minutes to move the fuel
and stabilizer through the fuel system.
If fuel in the engine has not been treated with STA-
BIL 360°® PROTECTION™, it must be drained into an
approved container. Then run the engine until it stops from
lack of fuel.
Storing the Engine
See the engine operator’s manual for instructions on how
to properly prepare the engine for storage.
Protecting the Pressure Washer
3. Turn o water and purge system.
4. Disconnect and drain all hoses, spray gun and spray
wand.
5. Empty pump of all liquids by pulling recoil handle
about six times.
NOTICE Store spray gun indoors and keep from freezing.
Protecting the Pump
6. Treat pump with Pump Saver.
Use Pump Saver to protect pump from damage caused by
mineral deposits and freezing. It also lubricates pistons and
seals. See Common Service Parts.
Read and follow all Pump Saver warnings and instructions.
If Pump Saver is not available, connect a 3 ft. (1 m)
section of garden hose to water inlet. Pour RV-antifreeze
(antifreeze without alcohol) into hose. Pull recoil handle
twice. Disconnect hose.
NOTICE You must protect your product from freezing
temperatures. Failure to do so will permanently damage
your pump and spray gun rendering your product
inoperable.
7. Store unit in a clean and dry area.
WARNING! Storage covers could cause a re
resulting in death or serious injury. Do not place
a storage cover over a hot pressure washer. Let
product cool before installing cover.
12 www.oregonproducts.com
Troubleshooting
Problem Cause Correction
Pump has following
problems: failure to
produce pressure, loss
of pressure, low water
volume.
1. Low pressure spray tip installed.
2. Inadequate water supply.
3. Clogged inlet hose screen.
4. Spray tip is obstructed.
5. Connections leak.
6. High pressure hose or spray gun leaks.
1. Replace with high pressure spray tip.
2. Provide adequate water ow.
3. Check and clean inlet hose screen.
4. Clean spray tip. See Spray Tip
Maintenance.
5. Tighten connections or replace o-rings.
6. Replace.
Detergent fails to mix
with spray.
1. High pressure spray tip installed.
2. Check ball stuck in detergent
siphoning system.
3. Detergent siphoning tube is clogged or
cracked.
1. Replace with low pressure black spray tip.
2. Free check ball. See Detergent Siphoning
Check Ball.
3. Clean or replace detergent siphoning
tube.
Engine will not start;
starts and runs rough
or shuts down during
operation.
1. Out of fuel.
2. Dirty air lter.
3. Spark plug wire not connected to spark
plug.
1. Fill fuel tank.
2. Clean or replace air lter.
3. Connect wire to spark plug.
For all other issues, see an authorized dealer.
*This pressure washer is rated in accordance to the Pressure Washer Manufacturers’ Association (PWMA) standard PW101-2010
(Testing and Rating Performance of Pressure Washers).
Specications
White, 40
°
...................................2500 PSI (172 bar) @ 2.7 GPM (10.2 L/min)*
Green, 25°....................................2600 PSI (179 bar) @ 2.6 GPM (9.8 L/min)*
Yellow, 15
°
...................................2600 PSI (179 bar) @ 2.6 GPM (9.8 L/min)*
Red, 0
°
......................................3100 PSI (214 bar) @ 2.4 GPM (9.1 L/min)*
Water Supply Temperature .....................................41°F (5°C) - 100°F (38°C)
min Water Supply Flow Rate ........................................3.7 GPM (14 L/min)
min Water Supply Pressure ...........................................20 PSI (1.38 bar)
13
80079614_EN Rev A
OREGON WARRANTY POLICY
LIMITED WARRANTY
Oregon® is a registered trademark of Blount, Inc. in the United States and other countries and is used under license to Briggs & Stratton Corporation. Briggs
& Stratton warrants that, during the warranty period specied below, it will repair or replace, free of charge, any part that is defective in material or workmanship
or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is eective for
and is subject to the time periods and conditions stated below. For warranty service, nd the nearest Authorized Service Dealer in our dealer locator map at
BRIGGSANDSTRATTON.COM. The purchaser must contact the Authorized Service Dealer, and then make the product available to the Authorized Service Dealer
for inspection and testing.
There is no other express warranty. Implied warranties, including those of merchantability and tness for a particular purpose, are limited to
the warranty period listed below, or to the extent permitted by law. Liability for incidental or consequential damages are excluded to the extent
exclusion is permitted by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you
specic legal rights and you may also have other rights which vary from state to state or country to country.**
WARRANTY PERIOD
* Applies to Briggs & Stratton engines only. Warranty coverage of non-Briggs & Stratton engines is provided by that engine manufacturer. Emissions-related
components are covered by the Emissions Warranty Statement.
** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount to a major failure. For warranty service, nd the nearest Authorized Service Dealer in our dealer
locator map at BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton
Australia Pty Ltd, 1 Moorebank Avenue, NSW, Australia, 2170.
The warranty period begins on the date of purchase by the rst retail or commercial consumer. “Consumer use” means personal residential household use by a
retail consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced
commercial use, it shall thereafter be considered as a commercial use product for purposes of this warranty.
Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the
product will be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.
ABOUT YOUR WARRANTY
Warranty service is available only through Briggs & Stratton Authorized Service Dealers. This warranty covers only defects in materials or workmanship. It does not
cover damage caused by improper use or abuse, improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.
Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the
Operator’s Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial
number on the product has been removed or the product has been altered or modied in any way, or if the product has evidence of abuse such as impact damage
or water/chemical corrosion damage.
Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and serviced
or repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by warranty.
Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when
normal use has exhausted the life of a part or the equipment. Maintenance and wear items such as lters, belts, cutting blades, and brake pads (except engine
brake pads) are not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.
Stale or Unapproved Fuel - In order to function correctly, this product requires fresh fuel that conforms to the criteria specied in the Operator’s Manual. Engine or
equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.
Other Exclusions - This warranty excludes damage due to accident, abuse, modications, alterations, improper servicing, freezing or chemical deterioration.
Attachments or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for
primary power in place of utility power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or
demonstration equipment or engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.
Item Consumer Use Commercial Use
Equipment 24 months 3 months
Engine* 24 months 3 months
Limpiadora a presión
Manual del operador
Número de modelo __________________________
Revisión __________________________________
Número de serie ____________________________
Fecha de compra ___________________________
Copyright © 2020. Briggs & Stratton Corporation
Milwaukee, WI, USA. Reservados todos los derechos.
Oregon es una marca registrada de Blount, Inc. en los United States y otros
región. Usa abajo licencia.
(833) 871-4330
www.oregonproducts.com
2
Índice de contenidos
Símbolos y sus signicados........................2
Descripción del equipo............................3
Características y controles.........................4
Operación ......................................6
Mantenimiento .................................10
Almacenamiento................................11
Solución de problemas...........................12
Garantía.......................................13
Registrar su producto
Para asegurar pronta y completa cobertura de
la garantía, registre su producto en línea en
www.onlineproductregistration.com.
Símbolos y sus signicados
Señal Signicado
PELIGRO
Indica un riesgo que, si no se evita,
ocasionará la muerte o lesiones
graves.
ADVERTENCIA
Indica un riesgo que, si no se evita,
podría ocasionar la muerte o lesiones
graves.
ATENCIÓN
Indica un riesgo que, si no se evita,
podría ocasionar lesiones menores o
moderadas.
AVISO
Indica una información que se considera
importante pero que no está relacionada
con un peligro potencial.
Símbolo Nombre Explicación
Símbolo de
alerta de
seguridad
Indica un posible riesgo para su
integridad física.
Lea el
Manual del
operador
La omisión de las advertencias,
las instrucciones y el manual
del operador podría redundar
en lesiones graves o incluso la
muerte.
Gases
tóxicos
La descarga de escape del
motor contiene monóxido de
carbono, un gas tóxico que
puede matar en minutos. No
puede olerse ni verse.
Incendio
El combustible y sus vapores
son extremadamente
inamables, lo que podría
causar quemaduras o incendios
que resulten en lesiones graves
o la muerte.
El escape del motor puede
causar un incendio y ocasionar
lesiones graves o la muerte.
Símbolo Nombre Explicación
Inyección
de uido
La alta presión de agua puede
cortar la piel y causar heridas
graves y posible amputación.
Spray,
objetos
que salen
volando
Riesgo de lesión ocular. El
agua rociada podría salpicar o
expulsar objetos, lo que puede
provocar lesiones graves.
Supercie
caliente
El contacto con el área
del moe podría provocar
quemaduras y causar lesiones
graves.
Descarga
eléctrica
El contacto con los cables
eléctricos podría provocar
choque eléctrico y ocasionar
lesiones graves o la muerte.
Retroceso
El contragolpe del cable del
arrancador retráctil jalará la
mano y el brazo hacia el motor
más rápido de lo que usted
pueda soltarlo, lo que puede
causar huesos rotos, esguinces
o hematomas que resulten en
lesiones graves.
Quemadura
química
Los productos químicos
podrían causar quemaduras
que resulten en la muerte o en
lesiones graves.
Supercie
resbaladiza/
Caída
Supercies resbaladizas
mojadas podrían provocar
caídas que resulten en la
muerte o en lesiones graves.
Caída
El retroceso de la pistola puede
hacerle caer, lo que puede
ocasionarle la muerte o una
lesión grave.
¡ADVERTENCIA! Este producto puede
exponerlo a sustancias químicas, entre las que
se incluyen emisiones de escape de motor de
gasolina, reconocidas por el Estado de California como
causantes de cáncer, y monóxido de carbono, reconocido
por el Estado de California como causante de defectos de
nacimiento u otros problemas reproductivos. Para obtener
más información, visite www.P65Warnings.ca.gov.
¡ADVERTENCIA! Este producto contiene plomo
y compuestos de plomo que, de acuerdo al
estado de California, pueden causar defectos de
nacimiento u otros problemas reproductivos. Lávese las
manos después de manipular este producto. Cáncer y
Problemas Reproductivos – www.P65Warnings.ca.gov
3 www.oregonproducts.com
Descripción del equipo
Lea este manual cuidadosamente y familiarícese
con el producto. Conozca sus aplicaciones, sus
limitaciones y cualquier riesgo implicado. Conserve
estas instrucciones originales para futuras consultas.
Para facilitar los proyectos de limpieza para exteriores, esta
máquina limpiadora a alta presión impulsada por motor
utiliza una variedad de boquillas rociadoras y detergente.
Sepa cómo detener el producto y disminuir la presión
rápidamente. Mantenga el área de operación libre y no
permita que niños operen la lavadora a presión.
Manténgase alerta, observe lo que está haciendo. No haga
funcionar la lavadora a presión si está cansado o bajo la
inuencia de alcohol o drogas.
Se ha hecho todo lo posible para garantizar que la
información contenida en este manual sea precisa y actual.
Sin embargo, nos reservamos el derecho de realizar
cambios, alterar o mejorar el producto y este documento, en
cualquier momento sin previo aviso.
AVISO Si tiene alguna pregunta acerca del uso previsto,
póngase en contacto con el distribuidor autorizado. Este
equipo se ha diseñado para usarse con partes autorizadas
de Briggs & Stratton
®
únicamente.
Para toda pregunta relativa a la motor, llame a
American Honda Motor Company al (800) 426-7701
o visite www.honda-engines.com para localizar un
concesionario.
Este sistema de encendido por chispa cumple con la
norma canadiense CAN ICES-2/NMB-2.
Bomba — pistón de acero inoxidable, bomba de leva axial
que desarrolla la alta presión.
Entrada de agua — conexión para la manguera de jardín.
Etiqueta de identicación — proporciona el modelo y
número de serie de la lavadora a presión.
Manguera para alta presión — conecte un extremo de la
manguera a la bomba de agua y el otro a la pistola rociadora.
Toma de alta presión — conexión para la manguera de
alta presión.
Entrada de agua
Etiqueta de identicación
Manguera para alta presión
Bomba
Toma de alta presión
4
Características y controles
Compare las ilustraciones con su lavadora a presión para familiarizarse con la ubicación de los diversos controles y
advertencias del producto.
5 www.oregonproducts.com
Boquillas rociadoras — múltiples patrones para
diversas aplicaciones de limpieza.
Manguera del sifón para detergente — usado
para succionar detergente de la botella de
químicos a la corriente de agua de baja presión.
Pistola rociadora — controla el spray mediante
el gatillo. Incluye bloqueo del gatillo.
Sistema de enfriamiento automático — evita
daños a la bomba interna mediante la descarga
de agua tibia al suelo.
Vara rociadora — permite intercambiar los
boquillas rociadoras.
Boquillas rociadoras
Vara rociadora
Pistola rociadora
Sistema de enfriamiento
automático (en la bomba)
Manguera del sifón
para detergente
6
Operación
Paso 1: Ubicación segura
Antes de arrancar la lavadora a presión, hay dos
problemas de seguridad igualmente importantes con
respecto a la intoxicación por monóxido de carbono e
incendios que deben abordarse.
Ubicación durante el funcionamiento para reducir el
riesgo de intoxicación por monóxido de carbono
El escape del motor de todos los equipos que queman
combustibles fósiles, como la lavadora a presión, contiene
monóxido de carbono, un gas tóxico que puede ser mortal
en minutos. Además de que no se lo puede ver, es inodoro
e insípido. Incluso si no huele los gases del escape, puede
estar expuesto al monóxido de carbono.
En muchos estados, la ley requiere el uso de alarmas de
monóxido de carbono funcionales en los hogares. Se
trata de un dispositivo electrónico que detecta niveles
peligrosos de monóxido de carbono. Cuando se produce
una acumulación de monóxido de carbono, la alarma avisa
a los habitantes con un sonido y una luz indicadora, visible
e intermitente. Las alarmas de humo no pueden detectar el
monóxido de carbono.
¡ADVERTENCIA! La descarga de escape del
motor contiene monóxido de carbono, un gas
tóxico que puede matar en minutos. Además de
que no se lo puede ver, es inodoro e insípido. Incluso si no
huele los gases del escape, puede estar expuesto al
monóxido de carbono.
• Opere este producto solamente en exteriores, lejos de
ventanas, puertas y ventilaciones para reducir el riesgo
de que el monóxido de carbono se acumule y pueda
circular en espacios habitados.
• Instale alarmas de monóxido de carbono con baterías
o enchufe con batería de respaldo siguiendo las
instrucciones del fabricante. Las alarmas de humo no
pueden detectar el monóxido de carbono.
• No opere este producto dentro de hogares, garajes,
sótanos, espacios reducidos, cobertizos u otros
espacios parcialmente cerrados, incluso si usa
ventiladores o deja las puertas y ventanas abiertas. El
monóxido de carbono se puede acumular rápidamente
en estos espacios y puede permanecer durante horas,
incluso después de que se apaga este producto.
• Apunte el escape en la dirección opuesta de las casas y
de los espacios donde haya personas u objectos.
• Si comienza a sentirse mareado o débil cuando utiliza el
producto, tome aire fresco inmediatamente y consulte a
un médico. Puede haberse intoxicado con monóxido de
carbono.
Alarma de monóxido
de carbono
USE EN EXTERIORES - EVITE EL ENVENENAMIENTO POR
MONÓXIDO DE CARBONO
ALARMA(S) DE MONÓXIDO DE CARBONO
Instale alarmas de monóxido de carbono en el interior
de su casa. Sin alarmas de monóxido de carbono
en funcionamiento, es posible que no se dé cuenta
de que se está intoxicando y muriendo debido a una
intoxicación por monóxido de carbono.
apúntelo en dirección opuesta a la casa
MOFLE
7 www.oregonproducts.com
Ubicación durante el funcionamiento para reducir el
riesgo de incendio
¡ADVERTENCIA! Los gases y el calor del
escape pueden encender materiales
combustibles y estructuras, o dañar el tanque de
combustible y provocar un incendio, lo que podría resultar
en lesiones graves o la muerte.
• La lavadora a presión debe encontrarse al menos a
5 pies (1,5 m) de cualquier estructura, alero, árboles,
ventanas, puertas, cualquier abertura de pared, arbustos
o vegetación de más de 12 pulgadas (30,5 cm) de altura.
• No coloque la lavadora a presión debajo de una
plataforma ni de ningún otro tipo de estructura que
pueda limitar el ujo de aire. Se deben instalar y
mantener alarmas de humo en el interior de acuerdo con
las instrucciones o recomendaciones del fabricante.
• Las alarmas de monóxido de carbono no pueden
detectar el humo.
• Es una violación del Código de Recursos Públicos de
California, Sección 4442, utilizar u operar el motor en
cualquier espacio cubierto con árboles, maleza o pasto
a menos que el sistema de escape esté equipado
con un extintor de chispas, como lo dene la Sección
4442, mantenido en correcto funcionamiento. Otras
jurisdicciones federales o estatales pueden tener leyes
similares. Para obtener más información, consulte la
Parte 261.52 de la Regulación Federal 36 del CFR.
• Póngase en contacto con el vendedor, el distribuidor o el
fabricante del equipo original para obtener un extintor de
chispas diseñado para el sistema de escape instalado
en este motor.
• Las piezas de repuesto deben ser iguales y se deben
instalar en la misma posición que las piezas originales.
Paso 2: Aceite y Combustible
Comprobación del nivel de aceite
1. Asegúrese de que la lavadora a presión esté en una
supercie nivelada.
2. Consulte el manual del operario del motor para añadir
al motor el aceite y el combustible recomendado.
Transporte
No incline el motor ni el equipo en un ángulo que provoque
un derrame de combustible.
Paso 3: Conguración General
Limpie los residuos
Limpie los residuos acumulados. Mantenga el área
alrededor del moe libre de residuos.
• Use un cepillo de cerda suave para eliminar los restos
de suciedad o aceite endurecidos.
• Use un paño húmedo para limpiar las supercies exteriores.
Lubrique las juntas tóricas
Lubrique todas las conexiones que se muestran para
prolongar la vida útil de las juntas tóricas.
1. Inspeccione y limpie las supercies de conexión antes
de la lubricación y el montaje. Reemplace las juntas
tóricas dañadas o faltantes. Consulte la sección
Repuestos comunes.
AVISO Nunca repare las fugas en conexiones con
selladores de ninguna clase. Reemplace la junta tórica.
2. Utilice una brocha pequeña o un hisopo para recubrir
las juntas tóricas directamente con una pequeña
cantidad de grasa.
Vericar/Conectar la pistola y manguera
1. Si el gatillo de la pistola rociadora se presiona
sin presionar el bloqueo del gatillo, o si la pistola
rociadora permanece presionado cuando se libera,
reemplace la pistola rociadora de inmediato.
2. Si la manguera de alta presión está dañada y la malla
interior está expuesta, reemplácela de inmediato.
5 pies (1.5m) mín.
MOFLE
5 pies
(1.5m) min.
Pistola
rociadora
Manguera de
presión alta
Vara rociadora
Bloqueo de
gatillo
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
Simplicity 021019-00 Manuel utilisateur
- Catégorie
- Nettoyeurs haute pression
- Taper
- Manuel utilisateur
dans d''autres langues
Documents connexes
-
Simplicity 020821-00 Manuel utilisateur
-
-
-
-
-
-
-
-
-