Hoover HTPS64SCTTWIFI Manuel utilisateur

Instruction Manual For Induction Hob

ENGLISH

Manuel d'instruction pour plaque à induction

FRANÇAIS

Manuale di istruzioni per il piano cottura a induzione

ITALIANO

MODEL: HTPS64SCTTWIFI

Thank you for purchasing the HOOVER induction hob. Please read this instruction

manual carefully before using the hob and keep it in a safe place for future reference.

EN-1

By placing the mark on this product, we are

confirming compliance to all relevant European

safety, health and environmental requirements

which are applicable in legislation for this

product.

Hereby, Candy Hoover Group Srl declares that

the radio equipment is in compliance with

Directive 2014/53/EU. The full text of the EU

declaration of conformity is available at the

following internet address: www.candy-

group.com

Safety Warnings

Your safety is important to us. Please read this

information before using your cooktop.

Installation

Electrical Shock Hazard

• Disconnect the appliance from the mains

electricity supply before carrying out any work

or maintenance on it.

• Connection to a good earth wiring system is

essential and mandatory.

• Alterations to the domestic wiring system must

only be made by a qualified electrician.

• Failure to follow this advice may result in

electrical shock or death.

EN-2

Cut Hazard

• Take care - panel edges are sharp.

• Failure to use caution could result in injury or

cuts.

Important safety instructions

• Read these instructions carefully before

installing or using this appliance.

• No combustible material or products should

be placed on this appliance at any time.

• Please make this information available to the

person responsible for installing the appliance

as it could reduce your installation costs.

• In order to avoid a hazard, this appliance must

be installed according to these instructions for

installation.

• This appliance is to be properly installed and

earthed only by a suitably qualified person.

• This appliance should be connected to a circuit

which incorporates an isolating switch

providing full disconnection from the power

supply.

• Failure to install the appliance correctly could

invalidate any warranty or liability claims.

Operation and maintenance

Electrical Shock Hazard

• Do not cook on a broken or cracked cooktop. If

the cooktop surface should break or crack, switch

the appliance off immediately at the mains power

EN-3

supply (wall switch) and contact a qualified

technician.

• Switch the cooktop off at the wall before

cleaning or maintenance.

• Failure to follow this advice may result in

electrical shock or death.

Health Hazard

• This appliance complies with electromagnetic

safety standards.

• However, persons with cardiac pacemakers or

other electrical implants (such as insulin

pumps) must consult with their doctor or

implant manufacturer before using this

appliance to make sure that their implants will

not be affected by the electromagnetic field.

• Failure to follow this advice may result in death.

Hot Surface Hazard

• During use, accessible parts of this appliance

will become hot enough to cause burns.

• Do not let your body, clothing or any item other

than suitable cookware contact the Induction

glass until the surface is cool.

• Metallic objects such as knives, forks, spoons

and lids should not be placed on the hob surface

since they can get hot

• Keep children away.

• Handles of saucepans may be hot to touch.

Check saucepan handles do not overhang other

cooking zones that are on. Keep handles out of

reach of children.

• Failure to follow this advice could result in

EN-4

burns and scalds.

Cut Hazard

• The razor-sharp blade of a cooktop scraper is

exposed when the safety cover is retracted. Use

with extreme care and always store safely and

out of reach of children.

• Failure to use caution could result in injury or

cuts.

Important safety instructions

• Never leave the appliance unattended when in

use. Boilover causes smoking and greasy

spillovers that may ignite.

• Never use your appliance as a work or storage

surface.

• Never leave any objects or utensils on the

appliance.

• Do not place or leave any magnetisable objects

(e.g. credit cards, memory cards)or electronic

devices (e.g. computers, MP3 players) near the

appliance, as they may be affected by its

electromagnetic field.

• Never use your appliance for warming or

heating the room.

• After use, always turn off the cooking zones

and the cooktop as described in this manual (i.e.

by using the touch controls). Do not rely on the

pan detection feature to turn off the cooking

zones when you remove the pans.

• Do not allow children to play with the appliance

EN-5

or sit, stand, or climb on it.

• Do not store items of interest to children in

cabinets above the appliance. Children climbing

on the cooktop could be seriously injured.

• Do not leave children alone or unattended in

the area where the appliance is in use.

• Children or persons with a disability which

limits their ability to use the appliance should

have a responsible and competent person to

instruct them in its use. The instructor should be

satisfied that they can use the appliance without

danger to themselves or their surroundings.

• Do not repair or replace any part of the

appliance unless specifically recommended in the

manual. All other servicing should be done by a

qualified technician.

• Do not use a steam cleaner to clean your

cooktop.

• Do not place or drop heavy objects on your

cooktop.

• Do not stand on your cooktop.

• Do not use pans with jagged edges or drag pans

across the Induction glass surface as this can

scratch the glass.

• Do not use scourers or any other harsh

abrasive cleaning agents to clean your cooktop,

as these can scratch the Induction glass.

• If the supply cord is damaged, it must be

replaced by the manufacturer, its service agent

or similarly qualified persons in order to avoid a

hazard.

EN-6

• This appliance is intended to be used in

household and similar applications such as:

-staff kitchen areas in shops, offices and other

working environments; -farm houses; -by

clients in hotels, motels and other residential

type environments; -bed and breakfast type

environments.

•WARNING: The appliance and its accessible

parts become hot during use.

Care should be taken to avoid touching heating

elements.

Children less than 8 years of age shall be kept

away unless continuously supervised.

• This appliance can be used by children aged

from 8 years and above and persons with

reduced physical, sensory or mental capabilities

or lack of experience and knowledge if they have

been given supervision or instruction concerning

use of the appliance in a safe way and

understand the hazards involved.

• Children shall not play with the appliance.

Cleaning and user maintenance shall not be

made by children without supervision.

• WARNING: Unattended cooking on a hob with

fat or oil can be dangerous and may result in fire.

NEVER try to extinguish a fire with water, but

switch off the appliance and then cover flame e.g.

with a lid or a fire blanket.

• WARNING: Danger of fire: do not store items on

the cooking surfaces.

EN-7

• Warning: If the surface is cracked, switch off

the appliance to avoid the possibility of electric

shock, for hob surfaces of glass-ceramic or

similar material which protect live parts

• A steam cleaner is not to be used.

• The appliance is not intended to be operated by

means of an external timer or separate

remote-control system.

CAUTION: The cooking process has to be

supervised. A short term cooking process has to be

supervised continuously.

WARNING: In order to prevent tipping of the

appliance, this stabilizing means must be

installed. Refer to the instructions for

installation.

WARNING: Use only hob guards designed by the

manufactuer of the cooking appliance or

indicated by the manufacture of the appliance in

the instruction for use as suitable or hob guards

incorporated in the appliance. The use of

inappropriate guards can cause accidents.

This appliance incorporates an earth connection

for functional purposes only.

Congratulations on the purchase of your new Induction Hob.

We recommend that you spend some time to read this Instruction / Installation

Manual in order to fully understand how to install correctly and operate it.

For installation, please read the installation section.

Read all the safety instructions carefully before use and keep this Instruction /

Installation Manual for future reference.

EN-8

1.2000 W zone, boost to 2600W

2.1500 W zone, boost to 2000W

3.2000 W zone, boost to 2600W

4.1500 W zone, boost to 2000W

5. Flex zone, 2800w boost to 3500w

6.Glass plate

7.Control panel

1. Heating zone selection controls

2. Timer control

3. Timer regulating key

4. keylock control

5. ON/OFF control

6. Boost function control

7. Pause function

8. Direct cook button

9. WiFi button

10. Power regulating key

11. Keep warm function control

12. Flex zone

Product Overview

Top View

Control Panel

EN-9

iron pot

magnetic circuit

ceramic glass plate

induction coil

induced currents

A Word on Induction Cooking

Induction cooking is a safe, advanced, efficient, and economical cooking

technology. It works by electromagnetic vibrations generating heat directly in the

pan, rather than indirectly through heating the glass surface. The glass becomes

hot only because the pan eventually warms it up.

Before using your New Induction Hob

• Read this guide, taking special note of the ‘Safety Warnings’ section.

• Remove any protective film that may still be on your Induction hob.

Using the Touch Controls

• The controls respond to touch, so you don’t need to apply any pressure.

• Use the ball of your finger, not its tip.

• You will hear a beep each time a touch is registered.

• Make sure the controls are always clean, dry, and that there is no object (e.g. a

utensil or a cloth) covering them. Even a thin film of water may make the

controls difficult to operate.

EN-10

Choosing the right Cookware

• Only use cookware with a base suitable for induction

cooking. Look for the induction symbol on the

packaging or on the bottom of the pan.

• You can check whether your cookware is suitable by carrying out

a magnet test. Move a magnet towards the base of the pan. If it

is attracted, the pan is suitable for induction.

• If you do not have a magnet:

1. Put some water in the pan you want to check.

2.

If does not flash in the display and the water is heating, the pan is suitable.

• Cookware made from the following materials is not suitable: pure stainless steel, aluminium or

copper without a magnetic base, glass, wood, porcelain, ceramic, and earthenware.

Do not use cookware with jagged edges or a curved base.

Make sure that the base of your pan is smooth, sits flat against the glass, and is

the same size as the cooking zone. Use pans whose diameter is as large as the

graphic of the zone selected. Using a pot a slightly wider energy will be used at its

maximum efficiency. If you use smaller pot efficiency could be less than expected.

Always centre your pan on the cooking zone.

Always lift pans off the Induction hob – do not slide, or they may scratch the glass.

EN-11

Pan dimensions

The cooking zones are up to a limit, automatically adapted to the diameter of the

pan. However the bottom of this pan must have a minimum of diameter according

to the corresponding cooking zone. To obtain the best efficiency of your hob,

please place the pan in the centre of the cooking zone.

The base diameter of induction cookware

Cooking zone

Minimum (mm)

1,2,3,4 (180mm)

120

Flex zone

240 or 160*270

The above may vary according to the quality of the pan used.

Using your Induction Hob

To start cooking

1. Touch the ON/OFF control.

After power on, the buzzer beeps once, all displays show

“ – “ or “ – – “, indicating that the induction hob has entered

the state of standby mode.

2. Place a suitable pan on the cooking zone that

you wish to use.

• Make sure the bottom of the pan and the surface

of the cooking zone are clean and dry.

3. Touching the heating zone selection control, and

a indicator next to the key will flash.

4. Select one heating zone and set a power level by touching the slider, or slide

along the “—”control, or just touch any point of the “—”.,

EN-12

Or

a. If you don’t select a heat zone within 1 minute, the ceramic hob will

automatically switch off. You will need to start again at step 1.

b. You can modify the heat setting at any time during cooking.

c. If slide along the “—”, power will vary from stage 2 to stage 8.

Press “-”, power will decrease by one stage each time till stage 0.

Press “+”, power will increase by one stage each time till stage 9.

If the display flashes alternately with the heat

setting

This means that:

• you have not placed a pan on the correct cooking zone or,

• the pan you’re using is not suitable for induction cooking or,

• the pan is too small or not properly centred on the cooking zone.

No heating takes place unless there is a suitable pan on the cooking zone.

The display will automatically turn off after 1 minutes if no suitable pan is placed

on it.

When you have finished cooking

1. Touching the heating zone selection control that you wish to

switch off.

2. Turn the cooking zone off by slide along the “—” to the left point, and then hold

for 1 second.

Make sure the power display shows “0”, then shows “H”.

and then

EN-13

3. Turn the whole cooktop off by touching the

ON/OFF control.

4. Beware of hot surfaces

‘H’ will show which cooking zone is hot to touch. It will disappear when the

surface has cooled down to a safe temperature. It can also be used as an

energy saving function if you want to heat further pans, use the hotplate

that is still hot.

Using the Power Management

Using power managerment you can set the total power to 2.5kW/ 3.0kW/ 4.5kW/

6.5kW and 7.4kW. The default total power setting is the maximum power level.

Setting the total power level to fit your requirement

1. Make sure the cooktop is turned off.

Note: you can only set power management when the cooktop is turned off.

2. Touch the button “pause function” and hold for 5 seconds. You can

hear the buzzer beeps one time.

3. After you hear the beep, touch “+” and “-” button at the same time

and hold for 3 second, the timer indicator will show flashing previous total power

level, e.g. ‘2.5’. Touch and hold ” +” and ”-” for 1 second again to switch to other

power level, for example 3.0. When the power that you want is flashing, touch the

button “pause function” and hold for 5 seconds. The buzzer will beep 10 times. It

means you have finished the

setting.

Note:

1. After step 2, you must touch the “+” and “-” within 3 seconds after you hear

the beep. Otherwise you will need to start again from step 2.

2. Once finish setting, wait till the end of 10 beeps. Do not touch any button during

this period. Otherwise the setting will be invalid.

EN-14

Power management Rules

If total power exceeds the limitation of 2.5kw, 3.0kw, 4.5kw, 6.5kw (depending

on which level you’ve set), you are not able to increase power stage of any zone.

If you increase it by touching ‘+’, the cooktop will beep 3 times and indicator will

show a flashing ‘Pn’. Thus you need to decrease power stage of other zones before

increasing the power of objective zone.

Direct Cook

First, download the hOn App and install to your portable device. Then enroll your

induction hob.

Switch on the hob, touch the WiFi button and hold for 3 seconds, the hob will

display ‘rr’, and the WiFi indicator light will flash, then you can start the enrollment.

Once the WIFI module connects the router successfully, the WiFi indicator light

will be on all the time. Otherwise the WiFi indicator light will keep flashing.

How to set

Set the direct cook procedure on hOn App, and send the command to the hob, you

will hear two beeps and the dot of the timer display will flash. Then touch the

Direct cook button, you will hear one beep and the dot of the timer display will be

fixed. The hob will work following the setting on App and the selected zones will

show “A.”. On the App you will have access to 15 assisted cooking recipes,

together with some special functions: Keep warm, Melting, Boiling, Simmering

and Frying.

Attention:

There is a special case. If all the zone indicator lights went out when you’ve set

cooking recipes on App, you’ll need to touch On/off button before touching Direct

cook button. Once all indicator lights went out, within 10 minutes you need to

finish the cooking recipe setting. Otherwise you will need to connect the router

and set the recipe again.

EN-15

a. WIRELESS PARAMETERS

Technology

Wi-Fi

BLE

Standard

802.11 b/g/n

v4.2 BR/EDR &BLE

Frequency Band(s) [MHz]

2400 ~ 2500

Maximum Power [mW]

100

8

b. PRODUCT INFORMATION FOR NETWORKED EQUIPMENT

Product information for networked equipment

power consumption of the product in networked

standby if all wired network ports are connected

and all wireless network ports are activated:

N/A

How to activate wireless network port:

For WiFi activation, press 3 seconds

the WiFi button

How to deactivate wireless network port:

For WiFi de-activation, press 3

seconds the WIFI button

EN-16

Using the Boost

Boost is the function that one zone rising to a larger power in one second and

lasting for 5 minutes. Thus you can get a more powerful and faster cooking.

Using the Boost to get larger power

1. Touch the heating zone selection button that you wish to

boost, an indicator next to the key will flash.

2. Touch the “b” button and hold 3 second, the heating zone will begin to work at

Boost mode. The power display will show “P” to indicate that the zone is

boosting.

3. The Boost power will last for 5 minutes and then the zone will go back to the

power stage 9.

4. If you want to cancel the Boost during this 5 minutes, touch the “B” button for

twice. The heating zone will go back to “9” power stage. Or slide along the “—” to

the left point, the heating zone will go back to the power stage in which you

touched.

Or

Restrictions when using

The four zones were divided into two groups. In one group, if use boost on one

zone, first make sure that the other zone is working on/below power level 5.

EN-17

Using the Keep warm

Keep warm function is suitable for keeping food warm.

Using the Keep warm to get stable temperature

1. Touch the heating zone selection button that you wish to

use keep warm, an indicator next to the key will flash.

2. Touch the button , then hold 3 second, the cooking zone indicator will

display “A”.

3. If you want to cancel the keep warm, touch the heating zone selection

button, and then touch the button for 3 second. The heating zone

will go back to “0” power stage.

Using the Pause function

Pause function can be used at any time during cooking. It allows to stop the

induction cooktop and come back to it.

1. Make sure the cook zone is working.

2. Touch the button pause function, the cooking zone indicator will show “ll”.

And then the operation of the induction cooktop will be deactivate within the scope

of all cooking zones, except the pause function, on/off and lock keys.

EN-18

3. To cancel the pause status, touch the button pause function, then the cooking

zone will go back to the power stage which you set before.

Flexible area

• This area can be used as a single zone or as two different zones, accordingly to

the cooking needs anytime.

• Flexible area is made of two independent inductors that can be controlled

separately.

• Important: Make sure to place the cookwares centered on the single cooking

zone. In case of big pot, oval, rectangular and elongated pans make sure to place

the pans centered on the cooking zone covering both cross.

Examples for good and bad pot placements:

As big zone

1. Touch the flex zone selection button to activate the flexible area as a single big

zone, the indicator will show .

EN-19

2. Touch one of the heating zone selection button, then slide along the “—”control,

or just touch any point of the “—” to adjust the power level.

As two independent zones

1. If you want to cancel the flex zone, just touch the button of the flex zone, the

indicator next to the flex zone button will disappear.

Locking the Controls

• You can lock the controls to prevent unintended use (for example children

accidentally turning the cooking zones on).

• When the controls are locked, all the controls except the ON/OFF control are

disabled.

To lock the controls

Touch the keylock control. The timer indicator will show “ Lo “

To unlock the controls

1. Make sure the Induction hob is turned on.

2. Touch and hold the keylock control for a while

3. You can now start using your Induction hob.

When the hob is in the lock mode, all the controls are disable except the ON/OFF,

you can always turn the induction hob off with the ON/OFF control in an emergency,

but you shall unlock the hob first in the next operation.

Over-Temperature Protection

A temperature sensor equipped can monitor the temperature inside the Induction

hob. When an excessive temperature is monitored, the Induction hob will stop

operation automatically.

Over-spillage Protection

Over-spillage protection is a safety protection function. It switch off the hob

automatically within 10s if the water flow to the control panel, while buzzer will

beep 1 second.

Detection of Small Articles

When an unsuitable size or non-magnetic pan (e.g. aluminium), or some other

La page charge ...

Hoover HTPS64SCTTWIFI Manuel utilisateur

Hoover HTPS64SCTTWIFI Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents