I
A
B
C
D
E
F
F
G
H
J
K
O
(A) TC-HE-28-601 Tank Cover
Couvercledu réservoir
Tapa del tanque
GA700590-GEG1 Lid Locker
Verrou de couvercle
Seguro de tapa
(C) 99-840-WH Tank Lever
Levier du réservoir
Palanca del tanque
*(2) Tank Bolt
Boulon de réservoír
Tornillo de tanque
*(2) Rubber Washer
Rondelle en caoutchouc
Arandela de goma
*(1) Tank to Bowl Gasket
Joint réservoir/cuvette
Junta de la cisterna y el inodoro
*(2) Channel Pads
Coussinet de canal
Tacos acanalados
P
GC55011943-GEG1 Toilet Seat
siège de toilette
Taza de inodoro
*(1) B/C Coupling Nut
Écrou de raccordement
B/C Tuerca de unión
(2) 99-287 Plastic Bolt Caps & Washer
Rondelle et chapeau de boulon en plastique
Casquete plástico para tornillo y arandela
NOTE: Parts with * are included in unit bag, 99-828
REMAQUE: Les piéces portant un * sont incluses dans ie sac.
AVISO: Las partes con * están incluidas en la bolsa de la unidad.
(k) Bowl
Cuvette
Taza
*(4) Plastic Wing Nut
Écrou papillon en plastique
Tuercas de orejas plásticas
(B) Tank
Réservoir
Tanque
METAL/COPPER
TUBING
GALVANIZED
PIPE (SEE NO TE)
METAL FLANGED
TUBING
METAL SPIRAL
TUBING
LOCK NUT
CONE
WASHER
COUPLING
NUT
WATER
SHUT-OFF
WATER
SHUT-OFF
LOCK NUT
LOCK NUT
LOCK NUT
O-RNG
COUPLING
NUT
WATER
SHUT-OFF
WATER
SHUT-OFF
EXISTING
WASHER
EXISTING
CONE
WASHER
EXISTING
COUPLING
NUT
COUPLING
NUT
These parts must be used as illustrated to insure
water-tight connection. Use of existing a coupling
nut may result in water leakage. Water supply tube
or pipe must extend at least 1/2'' inside threaded
shank of valve(does not apply to flanged tubing).
Use existing
coupling nut
and washer.
Use existing spiral cone
washer. Fluidmaster cone
washer may not seal
completely on spiral type
supply line.
FOR GALVANIZED
PIPE ONLY. you
must break out
the center of
COUPLING NUT
by striking it lightly with ahammer
or blunt end of screw driver handle.
Discard center portion. Also,use
O-RING instead of cone washer.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potentiial flooding.
CAUTION:
DO NOT
USE
CONE
WASHER
OR
O-RING
WITH
PLASTIC
SUPPLY
LINE.
Float Cup
Coupelle flottante
Flotador
M
Flapper Assembly Replaced by 99-788
L’etancheite Du Clapet
Asamblea De Flotador
PEEWEE™ is a trademark of GERBER PLUMBING FIXTURES LLC.
FLUIDMASTER is the registered trademark of Fluidmaster lnc.
8CGE0091 , rev. 07-15
L
Water Level
Adjusting Screw
La vis de réglage de
niveau d’eau
El tornillo de reglaje del
nivel de agua
Replaced by GA700132-GEG1
PEEWEE™ TOILET
DIRECTIONS FOR TANK TO BOWL ASSEMBLY
This water closet has been designed for easy installation. Conventional
fittings have been used throughout so that the working parts and operation
of this assembly may be easily understood.
1. Before assembling tank (B) to bowl (K) check tightness of lock nuts on both flush valve
and fill valve.
2. Assemble tank bolts (D) in tank with rubber washers (E) and plastic wing nuts (F). Wing
nuts should be tightened by hand sufficiently to compress rubber washers and insure
water seal.
3. Assemble tank to bowl gasket (G) to flush valve shank so that lock nut is enclosed in recess,
making sure that the entire surface of the washer is in contact with the tank bottom.
4. Place two channel pads (H) in recesses on back of bowl ledge to prevent china-to-china
contact.
5. Place tank assembly in position. All parts are supplied. USE NO PUTTY. Plastic wing nuts
(F) are tightened by hand sufficiently to prevent rocking; and since the tank bolts are
already sealed, the tank can be leveled by the relative amount that each wing nut is pulled
down on the three points of contact-tank to bowl gasket (G) and two channel pads (H).
6. Plastic bolt caps and washers (J) are provided to be used as indicated in the illustration.
7. The fill valve coupling nut (l) is provided to connect the water supply line to the fill valve.
USE NO PlPE DOPE! HAND TIGHTEN ONLY! OVERTIGHTENING MAY SPLIT THE FILL
VALVE AND WILL VOID THE WARRANTY!
8. Make sure refill tube adaptor is attached to the top of the flush valve overflow tube.
Note: Flow from the refill tube must be positioned directly over the overflow tube.
9. IMPORTANT: Always clear sand and rust from system.
• Remove valve top by lifting arm and rotating top 1/8 turn counterclockwise.
• While holding a container over the uncapped valve to prevent splashing, turn
water supply on and off a few times. Leave water supply off.
• Replace TOP by engaging lugs and rotating 1/8 turn clockwise. MAKE CERTAIN TOP IS
TURNED TO THE LOCKED POSITION. VALVE MAY NOT TURN ON IF TOP IS NOT FULLY
TURNED TO THE LOCKED POSITION.
10. Adjust water level in tank to marked water line. Turn the water level adjustment screw (L)
to move the float cup (M) up or down.
1 1. Check action and nut tightness (left hand thread) of tank lever (C). Also, check looseness of
flapper chain (there should be slight slack in chain when at rest) and seal of flush valve flapper.
1 2. Install the tank cover into the tank with lid locker (O).
1 3. Install toilet seat (P) per manufacturer’s instruction.
DO NOT EXPOSE PLASTIC TRIM PARTS TO STRONG OXIDIZING AGENTS, CHLORINE,
OR ACID LEVELS OF LOWER THAN 5.0 pH. SOME BOWL/TILE CLEANERS CONTAIN
SUCH AGENTS.
TANK TYPE BOWL CLEANERS CAN CAUSE TANK COMPONENT FAILURE AND
DAMAGE. OUR WARRANTY EXCLUDES SUCH FAILURES.
DO NOT USE IN-TANK DROP-IN TOILET BOWL CLEANERS CONTAINING
CHLORINE OR BLEACH. Use of in-tank drop-in cleaners containing chlorine or
bleach VOIDS FLUIDMASTER™ WARRANTY and WILL RESULT IN DAMAGE to tank
components and may cause flooding and property damage.
www.gerberonline.com
I
A
B
C
D
E
F
F
G
H
J
K
O
(A) TC-HE-28-601 Tank Cover
Couvercledu réservoir
Tapa del tanque
A700590-GEG1 Lid Locker
Verrou de couvercle
Seguro de tapa
(C) A700343-GEG1 Tank Lever
Levier du réservoir
Palanca del tanque
*(2) Tank Bolt
Boulon de réservoír
Tornillo de tanque
*(2) Rubber Washer
Rondelle en caoutchouc
Arandela de goma
*(1) Tank to Bowl Gasket
Joint réservoir/cuvette
Junta de la cisterna y el inodoro
*(2) Channel Pads
Coussinet de canal
Tacos acanalados
P
C55011943-GEG1 Toilet Seat
siège de toilette
Taza de inodoro
*(1) B/C Coupling Nut
Écrou de raccordement
B/C Tuerca de unión
(2) A700548-GEG1 Plastic Bolt Caps & Washer
Rondelle et chapeau de boulon en plastique
Casquete plástico para tornillo y arandela
NOTE: Parts with * are included in unit bag, A700549-GEG1
REMAQUE: Les piéces portant un * sont incluses dans ie sac.
AVISO: Las partes con * están incluidas en la bolsa de la unidad.
(k) Bowl
Cuvette
Taza
*(4) Plastic Wing Nut
Écrou papillon en plastique
Tuercas de orejas plásticas
(B) Tank
Réservoir
Tanque
METAL/COPPER
TUBING
GALVANIZED
PIPE (SEE NO TE)
METAL FLANGED
TUBING
METAL SPIRAL
TUBING
LOCK NUT
CONE
WASHER
COUPLING
NUT
WATER
SHUT-OFF
WATER
SHUT-OFF
LOCK NUT
LOCK NUT
LOCK NUT
O-RNG
COUPLING
NUT
WATER
SHUT-OFF
WATER
SHUT-OFF
EXISTING
WASHER
EXISTING
CONE
WASHER
EXISTING
COUPLING
NUT
COUPLING
NUT
These parts must be used as illustrated to insure
water-tight connection. Use of existing a coupling
nut may result in water leakage. Water supply tube
or pipe must extend at least 1/2'' inside threaded
shank of valve(does not apply to flanged tubing).
Use existing
coupling nut
and washer.
Use existing spiral cone
washer. Fluidmaster cone
washer may not seal
completely on spiral type
supply line.
FOR GALVANIZED
PIPE ONLY. you
must break out
the center of
COUPLING NUT
by striking it lightly with ahammer
or blunt end of screw driver handle.
Discard center portion. Also,use
O-RING instead of cone washer.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potentiial flooding.
CAUTION:
DO NOT
USE
CONE
WASHER
OR
O-RING
WITH
PLASTIC
SUPPLY
LINE.
Float Cup
Coupelle flottante
Flotador
M
Flapper Assembly Replaced by A700651-GEG1
L’etancheite Du Clapet
Asamblea De Flotador
PEEWEE™ is a trademark of GERBER PLUMBING FIXTURES LLC.
FLUIDMASTER is the registered trademark of Fluidmaster lnc.
8CGE0091 , rev. 07-15
L
Water Level
Adjusting Screw
La vis de réglage de
niveau d’eau
El tornillo de reglaje del
nivel de agua
Replaced by A700132-GEG1
PEEWEE™ TOILET
DIRECTIONS FOR TANK TO BOWL ASSEMBLY
This water closet has been designed for easy installation. Conventional
fittings have been used throughout so that the working parts and operation
of this assembly may be easily understood.
TOILETTE PEEWEE™ INODORO PEEWEE™
1. Before assembling tank (B) to bowl (K) check tightness of lock nuts on both flush valve
and fill valve.
2. Assemble tank bolts (D) in tank with rubber washers (E) and plastic wing nuts (F). Wing
nuts should be tightened by hand sufficiently to compress rubber washers and insure
water seal.
3. Assemble tank to bowl gasket (G) to flush valve shank so that lock nut is enclosed in recess,
making sure that the entire surface of the washer is in contact with the tank bottom.
4. Place two channel pads (H) in recesses on back of bowl ledge to prevent china-to-china
contact.
5. Place tank assembly in position. All parts are supplied. USE NO PUTTY. Plastic wing nuts
(F) are tightened by hand sufficiently to prevent rocking; and since the tank bolts are
already sealed, the tank can be leveled by the relative amount that each wing nut is pulled
down on the three points of contact-tank to bowl gasket (G) and two channel pads (H).
6. Plastic bolt caps and washers (J) are provided to be used as indicated in the illustration.
7. The fill valve coupling nut (l) is provided to connect the water supply line to the fill valve.
USE NO PlPE DOPE! HAND TIGHTEN ONLY! OVERTIGHTENING MAY SPLIT THE FILL
VALVE AND WILL VOID THE WARRANTY!
8. Make sure refill tube adaptor is attached to the top of the flush valve overflow tube.
Note: Flow from the refill tube must be positioned directly over the overflow tube.
9. IMPORTANT: Always clear sand and rust from system.
• Remove valve top by lifting arm and rotating top 1/8 turn counterclockwise.
• While holding a container over the uncapped valve to prevent splashing, turn
water supply on and off a few times. Leave water supply off.
• Replace TOP by engaging lugs and rotating 1/8 turn clockwise. MAKE CERTAIN TOP IS
TURNED TO THE LOCKED POSITION. VALVE MAY NOT TURN ON IF TOP IS NOT FULLY
TURNED TO THE LOCKED POSITION.
10. Adjust water level in tank to marked water line. Turn the water level adjustment screw (L)
to move the float cup (M) up or down.
1 1. Check action and nut tightness (left hand thread) of tank lever (C). Also, check looseness of
flapper chain (there should be slight slack in chain when at rest) and seal of flush valve flapper.
1 2. Install the tank cover into the tank with lid locker (O).
1 3. Install toilet seat (P) per manufacturer’s instruction.
12. Installer le couvercle de réservoir sur le réservoir avec verrou de couvercle (O).
13. Installer le siège de toilette (P) en suivant les instructions du fabricant.
12. Coloque la cubierta del depósito con el seguro de tapa (O).
13. Coloque la taza del inodoro (P) siguiendo las instrucciones del fabricante.
DO NOT EXPOSE PLASTIC TRIM PARTS TO STRONG OXIDIZING AGENTS, CHLORINE,
OR ACID LEVELS OF LOWER THAN 5.0 pH. SOME BOWL/TILE CLEANERS CONTAIN
SUCH AGENTS.
TANK TYPE BOWL CLEANERS CAN CAUSE TANK COMPONENT FAILURE AND
DAMAGE. OUR WARRANTY EXCLUDES SUCH FAILURES.
DO NOT USE IN-TANK DROP-IN TOILET BOWL CLEANERS CONTAINING
CHLORINE OR BLEACH. Use of in-tank drop-in cleaners containing chlorine or
bleach VOIDS FLUIDMASTER™ WARRANTY and WILL RESULT IN DAMAGE to tank
components and may cause flooding and property damage.
www.gerberonline.com
-
1
-
2
dans d''autres langues
- English: Gerber PEEWEE
Documents connexes
-
Gerber Hinsdale 1.28 gpf ADA Elongated Simple CT Bowl White Manuel utilisateur
-
-
-
Gerber Plumbing GAV21814 Manuel utilisateur
-
-
Gerber Plumbing GVP2156225 Guide d'installation
-
Gerber PeeWee C55011943 Manuel utilisateur
-
-
-
