Gamber-Johnson 7160-1265-10 Guide d'installation

Marque: Gamber-Johnson

Modèle: 7160-1265-10

Taper: Guide d'installation

Ce manuel convient également à

Product Mounting Disclaimer

Gamber-Johnson is not liable under any theory of contract or tort law for any loss, damage, personal injury, special, incidental or consequential damages for personal injury or other damage

of any nature arising directly or indirectly as a result of the improper installation or use of its products in vehicle or any other application. In order to safely install and use Gamber-Johnson

products full consideration of vehicle occupants, vehicle systems (i.e., the location of fuel lines, brakes lines, electrical, drive train or other systems), air-bags and other safety equipment is

required. Gamber-Johnson specifically disclaims any responsibility for the improper use or installation of its products not consistent with the original vehicle manufactures specifications

and recommendations, Gamber-Johnson product instruction sheets, or workmanship standards as endorsed through the Gamber-Johnson Certified Installer Program.

Rev I

7160-1265-xx (-P & -E)

TOUGHBOOK 20/FZ-G2 Docking Station

PS-001Printing Spec:

If you need assistance or have questions, call Gamber-Johnson at 1-800-456-6868

Form Revision

INSTALLATION INSTRUCTIONS

Product

INST-862

7170-0681-00 (Non-RF) or 7170-0681-02 (Dual-RF)

This instruction sheet is for the TOUGHBOOK 20/FZ-G2 docking station. For

instruction on features, set-up and operation of the computer, please refer to the

manual provided by Panasonic with the computer.

This docking station is designed to be used with a variety of Gamber-Johnson

mounting systems. Installation instructions for other Gamber-Johnson products are

provided with each individual product.

This instruction sheet is for the following products:

7160-1265-00, (-P) & (-E) Docking Station- No RF, Keyed Alike

7160-1265-02, (-P) & (-E) Docking Station- Dual RF, Keyed Alike

7160-1265-04, (-P) & (-E) Docking Station- No RF, Keyed Different

7160-1265-06, (-P) & (-E) Docking Station- Dual RF, Keyed Different

7160-1265-20, (-P) & (-E) Docking Station- Lite, No RF, Keyed Alike

7160-1265-22, (-P) & (-E) Docking Station- Lite, Dual RF, Keyed Alike

Panasonic recommends using the following Power Adapter to power the docking station.

It can be ordered from Gamber-Johnson seperately.

7300-0460 - Bare Wire Adapter (11-16 Vdc input) - Available with the docking station as

KIT

1 / 10

IMPORTANT SAFETY INFORMATION FOR INSTALLERS

Safety is dependent on the proper installation and servicing of this docking station. It is important to

read and follow all instructions before installing this product.

To properly install a Gamber-Johnson docking station you must have a good understanding of

automotive electrical procedures and systems, along with proficiency in the installation and service of

aftermarket vehicle equipment.

There are no adjustments required at any time of the electrical components within the docking station.

Opening the docking station will void the product warranty.

During Installation:

DO NOT connect this docking station to the vehicle battery until:

All other electrical connections are made1. Mounting of all components is complete2. Verification that no shorts exist in the entire system3.

DO NOT install equipment or route wiring or cords in the deployment path of any air bag.

When drilling into the vehicle, DO make sure that both sides of the surface are clear of anything that

could be damaged.

CAUTION: If wiring is shorted to the frame, high current conductors can cause hazardous sparks

resulting in electrical fires or flying molten metal.

After installation:

Test the docking station to ensure that it is working properly.

File these instructions in a safe place and refer to them when performing maintenance or re-

installing.

WARNING: Failure to follow all safety precautions and instructions may result in property damage,

serious injury, or death.

PRE-INSTALLATION RECOMMENDATOINS

Conduct a "Bench Test"

Gamber-Johnson strongly advises a "bench test" be conducted to verify all electronic and

software issues are resolved prior to installation:

Make sure the computer is operational by itself.1. Insert computer into the docking station and verify that the computer is 2. operating in the dock.

Interconnect entire assembly and verify start-up of all components, including 3. other equipment (printers, modems, scanners, etc.)

Gamber-Johnson recommends positioning of all mounts and equipment in the vehicle

prior to the actual install to verify that mounting locations are safe and practical.

2 / 10

If a Malfunction or Trouble Occurs, • Immediately Stop Use

If a Malfunction Occurs, Immediately

Unplug the Car Plug and Remove the

Computer from this product

• This product is damaged

• The connector pins are bent

• A foreign object is inside this product

• Smoke is emitted

• An unusual smell is emitted

• Unusually hot

Continuing to use this product while any

of the above conditions are present may

result in fire or electric shock.

• If a malfunction or trouble occurs,

immediately unplug the car plug and

remove the unit from this product. Then,

contact your technical support office for

repair.

Do Not Touch This Product or Cable • When It Starts Thundering

Electric shock may result.

Do Not Place Containers of Liquid or • Metal Objects on Top of This Product If

water or other liquid spills, or if paper

clips, coins, or foreign matter get inside

this product, fire or electric shock may

result.

• If foreign matter has found its way

inside, immediately unplug the car plug

and remove the unit from this product.

Then contact your technical support

office.

Avoid a Lot of Water, Moisture, Steam, • Dust, Oily Vapors, etc.

Otherwise, possibly resulting in fire or

electric shock.

Use Only the Specified Docking Station • with This Product

Using a Docking Station other than the

one supplied (supplied with the unit or

one sold separately as an accessory)

may result in a fire.

PRECAUTIONS FOR OPERATING THE DOCKING STATION

3 / 10

Do Not Connect a Telephone Line, or • a Network Cable Other Than the one

Specified, Into the LAN Port.

If the LAN port is connected to a

network such as the ones listed below,

a fire or electric shock may result.

• Networks other than 1000BASE-T,

100BASE-TX or 10BASE-T

• Phone lines (IP phone (Internet

Protocol Telephone), Telephone lines,

internal phone lines (on premise

switches), digital public phones, etc.)

Using this product continuously in a • hot environment will shorten the

product life. Avoid use in these types

of environments.

When using in hot or cold • environment, some peripherals may

fail to work properly. Check the

operation environment of the

peripherals.

Do Not Install This Product in • Unstable State

If balance of the unit is lost, it may fall

over or drop, resulting in an injury.

Docks used in the vertical (Tablet) • position must be installed with the lock

on TOP. Installing the dock upside

down may result in damage to the

computer.

Do Not Install This Product Where • There is a Lot of Water, Moisture,

Steam, Dust, Oily Vapors, etc.

Otherwise, a possibility of fire or

electric shock could result.

DOCKING AND UNDOCKING THE COMPUTER

DOCKING PROCEDURE

1. Ensure latch is in the "OPEN" Position

2. Extend the TOUGHBOOK 20/FZ-G2 handle to the "DEPLOYED" position then insert the

computer

3. Push the top of the TOUGHBOOK 20/FZ-G2 into the dock. The latch will move to the

"Docked" position

4. To secure the tablet ensure it is in the closed position with the display latch engaged

then move the lower latch into the locked position

*The secondary latch is specific to the Toughbook 20 computer. To lock the tablet portion of a

FZ-G2 computer, the dock must be updated by Gamber Johnson.

5. Push the TOUGHBOOK 20/FZ-G2 handle into the "STOWED" position

6. Push the lock to secure the device

NOTES:

Ensure latch is fully in the "Docked" position. It is recommended that the TOUGHBOOK

20/FZ-G2 is pushed into the dock with two hands. For TOUGHBOOK 20/FZ-G2 fitted with

Gadget option, it may be necessary to attach the main unit in the forward direction only. Refer

to device manual for further information.

NOTE:

Portions of your Docking Station may differ somewhat from the illustrations in the operating

instructions, but this should present no problems in actual use. Be sure to follow the operating

instructions when using your Docking Station.

4 / 10

TOUGHBOOK 20/FZ-G2 DOCKING STATION FEATURE

IDENTIFICATON

5 / 10

exluded on lite versions exluded on

lite versions

Serial Port

VGA Port HDMI Port

Antenna Switch

Ethernet Port

DC IN 16V, 4.06A

External Wireless

CH1: WWAM-GPS/ EX. ANT 2

External Wireless

CH1: WWAM/ EX. ANT 1

(2) USB 3.0 Ports

Lever

Lock

Secondary Latch

(compatible with TB 20 only)

CABLE MANAGMENT FEATURES AND PROPER INSTALLATION

1.) Use Zip ties (provided) to secure each port cable to the specific strain relief feature on the dock

If dock mount plate is covering ports

remove these screws

Power Ethernet USB USB

HDMI

VGA

ANT1 ANT2

Replace mount plate once wires

are connected and secured

CABLE TIE LOCATION

6 / 10

7 / 10

SPECIFICATIONS

Item Description

Power Supply Input DC 15.6V-16V Must use approved FCC/E-marked PSU

Expansion Bus Connector 24-Pin

USB Port* USB 3.0 x 2

LAN Port RJ-45 x 1

HDMI Port** HDMI x 1 For exclusive use with HDMI standard

VGA Port Mini Dsub 15-pin female (Analog interface)

Serial Port Dsub 9-pin male

Physical Dimension [WxHxD] 290x277x75mm (11.42x10.91x2.95")

Weight 2.28kg(5 lb)

* Does not guarantee operation of all USB and HDMI-compatible peripherals

** When connecting the HDMI compatible display, specifications such as maximum resolutions

available to output differ, depending on the specifications of the connected devices.

See the specifications of the connected device for details.

DIMENSIONAL DRAWING

Installation fixing 75mm VESA studs are provided in the areas indicated by

the arrows in the figure above.

8 / 10

Screen Support Mounting Locations

Use #6-32 screws from screen support hardware bag to attach screen support

to the left or right mounting location, do not over-torque screws.

Reccomended torque is 8-11 in/lbs.

Screen Support Installation

Screen supports are recommended on all laptop dock/cradles in

high-vibration environments.

Screen support can be purchased from www.GamberJohnson.com

Part Number: 7110-1275

Regulatory Model #: 7160-1265

GJ Model #'s:

7160-1265-00, 7160-1265-00-E, 7160-1265-00-P

7160-1265-02, 7160-1265-02-E, 7160-1265-02-P

7160-1265-04, 7160-1265-04-E, 7160-1265-04-P

7160-1265-06, 7160-1265-06-E, 7160-1265-06-P

7160-1265-20, 7160-1265-20-E, 7160-1265-20-P

7160-1265-22, 7160-1265-22-E, 7160-1265-22-P

Descriptions: Dock-Panasonic CF20/FZ-G2

Certifications:

EN 55032:2012 Class B• EN 50498:2010• EN 50581:2012• EN 62368-1•

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions.

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference

that may cause undesired operation.

REGULATORY CERTIFICATION INFORMATION

Gamber-Johnson LLC

3001 Borham Ave.

Stevens Point, WI, 54481

USA

715-344-3482

9 / 10

EN: Safety instructions for proper use

Precautions for Operating the Car Mounter

If a Malfunction Occurs, Immediately Unplug the Car Plug and Remove the Computer From this product•

Use Only the Specified Car Adaptor With This Product•

Avoid a Lot of Water, Moisture, Steam, Dust, Oily Vapors, etc•

Portions of your car mounter may differ somewhat from the illustrations in the operating instructions, but this should present •

no problems in actual use

For business users in the European Union. If you wish to discard electrical and electronic equipment, please contact your dealer

or supplier for further information.

Precautions for Installing the Car Mounter

Do Not Install This Product in Unstable State•

Do Not Install This Product Wherever There is a Lot of Water, Moisture, Steam, Dust, Oily Vapors, etc•

DE: Sicherheitshinweise bei einer ordnungsgemäßen Nutzung

Vorsichtsmaßnahmen beim Einsatz der Fahrzeughalterung

Entfernen Sie beim Auftreten einer Fehlfunktion unverzüglich das Fahrzeugnetzteil und trennen Sie die Verbindung zwischen •

Computer und dem Produkt

Verwenden Sie nur das angegebene Fahrzeugnetzteil für das Produkt•

Wasser, Feuchtigkeit, Dampf, Staub, ölige Dämpfe usw. vermeiden•

Einige Bereiche Ihrer Automontagevorrichtung können von den Abbildungen in der Bedienungsanleitung geringfügig •

abweichen, was für die tatsächliche Nutzung jedoch unerheblich ist.

Für Kunden in der Europäischen Union. Bitte treten Sie mit Ihrem Händler oder Lieferanten in Kontakt, wenn Sie elektrische und

elektronische Geräte entsorgen möchten. Er hält weitere Informationen für Sie bereit.

Vorsichtshinweise zum Einbau der Automontagevorrichtung

Installieren Sie das Produkt nicht in instabilem Zustand•

Installieren Sie das Produkt nicht in der Umgebung von Wasser, Feuchtigkeit, Dampf, Staub, öligen Dämpfen usw.•

FR: Consignes de sécurité pour une utilisation correcte

Précautions d’utilisation de auto monter

En cas de dysfonctionnement, débrancher immédiatement la fiche et déconnecter l’ordinateur de ce produit.•

Ne connectez pas au port pour réseau local un câble téléphonique ou un câble réseau autre que ceux spécifiés.•

Eviter le contact de l‘eau, de l’humidité, de la vapeur, de la poussière, des vapeurs graisseuses, etc.•

Certaines parties de votre auto monter peuvent différer quelque peu des illustrations imprimées dans les instructions •

d’utilisation mais cela ne doit présenter aucun problème lors de l’utilisation.

Utilisateurs professionnels de l’Union européenne. Pour en savoir plus sur l’élimination des appareils électriques et

électroniques, contactez votre revendeur ou fournisseur.

Précautions à prendre pour l’installation de l’Auto monter

Ne pas installer ce produit sur un support instable•

Ne pas installer ce produit en présence d’eau, d’humidité, de vapeur, de poussière, de vapeurs graisseuses,etc.•

10 / 10

Gamber-Johnson 7160-1265-10 Guide d'installation

Marque: Gamber-Johnson

Modèle: 7160-1265-10

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Gamber-Johnson 7160-1265-10 Installation guide

Gamber-Johnson 7160-1265-10 Guide d'installation

Ce manuel convient également à

Gamber-Johnson 7160-1265-10 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents