Lennox Hearth Products EBSTPE-2 Manuel utilisateur

Marque: Lennox Hearth Products

Modèle: EBSTPE-2

Catégorie: Cheminées

Taper: Manuel utilisateur

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

HOMEOWNER'S CARE AND

OPERATION INSTRUCTIONS

MODELS

RETAIN THESE INSTRUCTIONS

FOR FUTURE REFERENCE

FOR YOUR SAFETY: Do not store or use gasoline

or other flammable vapors or liquids in the vicin-

ity of this or any other appliance.

FOR YOUR SAFETY: What to do if you smell gas:

• DO NOT light any appliance.

• DO NOT touch any electrical switches.

• DO NOT use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone.

Follow your gas suppliers instructions.

• If your gas supplier cannot be reached, call the

fire department.

Installation and service must be performed by a

qualified installer, service agency or the gas

supplier.

WARNING: IF THE INFORMATION IN THIS MANUAL

IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLO-

SION MAY RESULT CAUSING PROPERTY DAM-

AGE, PERSONAL INJURY OR LOSS OF LIFE.

POUR VOTRE SÉCURITÉ: Ne pas entreposer ni utiliser

d'essence ni d'autre vapeurs ou liquides inflammables

dans le voisinage de cet appareil ou de tout autre

appareil.

POUR VOTRE SÉCURITÉ: Que faire si vous sentez une

odeur de gaz:

• Ne pas tenter d'allumer d'appareil.

• Ne touchez à aucun interrupteur. Ne pas vous servir

des téléphones se trouvant dans le batiment où

vous vous trouvez.

• Evacuez la piéce, le bâtiment ou la zone.

• Appelez immédiatement votre fournisseur de gaz

depuis un voisin. Suivez les instructions du

fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service dos incendies.

L'installation et service doit être exécuté par un

qualifié installeur, agence de service ou le fournisseur

de gaz.

AVERTISSEMENT: ASSUREZ-VOUS DE BIEN SUIVRE

LES INSTRUCTIONS DONNÉ DANS CETTE NOTICE POUR

RÉDUIRE AU MINIMUM LE RISQUE D'INCENDIE OU

POUR ÉVITER TOUT DOMMAGE MATÉRIEL, TOUTE

BLESSURE OU LA MORT.

B-VENT MULTI-OPEN

ELITE® SERIES

B-VENTED GAS APPLIANCES

P/N 875,012M REV. D 05/2004

EBST (See-through) EBPF (Peninsula)

EBCL (Corner-Left) EBCR (Corner-Right)

sledoMtlovilliMsledoMcinortcelE

2-MNTSBE2-MNRCBE2-ENTSBE2-ENRCBE

2-MPTSBE2-MPRCBE2-EPTSBE2-EPRCBE

2-MNFPBE2-MNLCBE2-ENFPBE2-ENLCBE

2-MPFPBE2-MPLCBE2-EPFPBE2-EPLCBE

MNYABBEPNYABBEENYABBE

OTL Report No. 116-F-07-5

2NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

These appliances are designed to operate on

natural or propane gas only.

Input of millivolt models is shown in the fol-

lowing table:

CONGRATULATIONS!

In selecting this LENNOX B-Vented Gas Appliance you have chosen the finest and

most dependable fireplace to be found anywhere. Its a beautiful, prestigious

alternative to a wood burning fireplace. Welcome to a Family of tens of thousands

of satisfied LENNOX Fireplace Owners.

Please carefully read and follow all of the instructions found in this manual. Please

pay special attention to the safety instructions provided in this manual. The

Homeowner's Care and Operation Instructions included here will assure that you

have many years of dependable and enjoyable service from your LENNOX product.

INTRODUCTION

The millivolt appliances are designed to operate

on either natural or propane gas. A millivolt gas

control valve with piezo ignition system pro-

vides safe, efficient operation. If any optional

accessories which require electrical power are

being installed, the electrical power must be

provided at the time of appliance installation.

The electronic appliances are designed to op-

erate on either natural or propane gas. An

electronic intermittent pilot system provides

safe, efficient operation. External electrical

power is required to operate these units.

These appliances comply with National Safety

Standards and are tested and listed by Omni-

Test Laboratories (Report No. 116-F-07-5) to

ANSI Z21.50 - 2000 (in Canada, CSA 2.22 -

2000), and CAN/CGA-2.17-M91 in both USA

and Canada, as vented gas fireplaces.

Installation must conform to local codes. In

the absence of local codes, installation must

comply with the current National Fuel Gas

Code, ANSI Z223.1 (NFPA 54). (In Canada, the

current CAN/CGA B149 installation code.) Elec-

trical wiring must comply with local codes. In

the absence of local codes, installation must

be in accordance with the National Electrical

Code, NFPA 70 - (latest edition). (In Canada,

the current CSA C22.1 Canadian Electric Code.)

TABLE OF CONTENTS

Introduction...................................... page 2

General Information.......................... page 2

Operation/Care of Your Appliance..... page 3

Gas Controls/Control Compartment,

Access ............................................ page 4

Variable Flame Adjustment ............... page 5

Outside Combustion Air Control ....... page 5

Venting Action and Safety Limit........ page 5

Maintenance ..................................... page 6

Front Glass Enclosure Panel,

Removal and Installation ................ page 6

Maintenance Schedule...................... page 7

Burner Adjustments.......................... page 8

Log Placement.................................. page 9

Vermiculite and Black/Gray Ceramic

Fiber Chunks Placement ................ page 9

Millivolt Appliance Checkout............. page 9

Electronic Appliance Checkout.......... page 10

Wiring Diagrams............................... page 10

Warranty........................................... page 10

Replacement Parts ............................ page 10

Product Reference Information ........ page 10

Accessory Components.................... page 11

Lighting Instructions – Millivolt........ page 14

Lighting Instructions – Electronic..... page 16

Troubleshooting Guide – Millivolt ...... page 18

Troubleshooting Guide – Electronic ... page 19

Replacement Parts List...................... page 21 WARNING: IMPROPER INSTALLATION,

ADJUSTMENT, ALTERATION, SERVICE

OR MAINTENANCE CAN CAUSE INJURY

OR PROPERTY DAMAGE. REFER TO THIS

MANUAL. FOR ASSISTANCE OR ADDI-

TIONAL INFORMATION CONSULT A

QUALIFIED INSTALLER, SERVICE

AGENCY OR THE GAS SUPPLIER.

GENERAL INFORMATION

Note: Installation and repair should be per-

formed by a qualified service person. The appli-

ance should be inspected annually by a quali-

fied professional service technician. More fre-

quent inspections and cleanings may be re-

quired due to excessive lint from carpeting,

bedding material, etc. It is imperative that the

control compartment, burners and circulating

air passage ways of the appliance be kept clean.

S'assurer que le brùleur et le compartiment des

commandes sont propres. Voir les instruc-

tions d'installation et d'utilisation qui

accompagnent l'appareil.

Provide adequate clearances around air open-

ings and adequate accessibility clearance for

service and proper operation. Never obstruct

the front openings of the appliance.

Due to high temperatures the appliance should

be located out of traffic and away from furni-

ture and draperies. Locate furniture and win-

dow coverings accordingly.

WARNING: THESE FIREPLACES ARE

VENTED DECORATIVE GAS APPLIANCES.

DO NOT BURN WOOD OR OTHER MATE-

RIAL IN THESE APPLIANCES.

Input of electronic models is shown in the

following table:

DO NOT ATTEMPT TO ALTER OR MODIFY

THE CONSTRUCTION OF THE APPLIANCE OR

ITS COMPONENTS. ANY MODIFICATION OR

ALTERATION MAY VOID THE WARRANTY,

CERTIFICATION AND LISTINGS OF THIS UNIT.

sledoMcinortcelE

enaporPdnalarutaN

sledoMsaG

)H/UTB(etartupnI

etaRdexiF

,2-ENFPBE,2-ENTSBE ,2-EPFPBE,2-EPTSBE ENYABBE 005,73

,2-ENRCBE,2-ENLCBE 2-EPRCBE,2-EPLCBE 000,43

sledoMtlovilliM

enaporPdnalarutaN

sledoMsaG

)H/UTB(etartupnI

detaludom-yllaunaM

,2-MNFPBE,2-MNTSBE ,2-MPFPBE,2-MPTSBE PNYABBE,MNYABBE 005,73OT000,03

,2-MNRCBE,2-MNLCBE 2-MPRCBE,2-MPLCBE 000,43OT000,62

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Carbon Monoxide Poisoning: Early signs of

carbon monoxide poisoning are similar to

the flu with headaches, dizziness and/or

nausea. If you have these signs, obtain

fresh air immediately. Turn off the gas

supply to the appliance and have it ser-

viced by a qualified professional, as it may

not be operating correctly.

OPERATION AND CARE OF YOUR

APPLIANCE

Appliance operation may be controlled by the

following means: the factory provided modesty

panel-mounted ON-OFF control switch, an op-

tional wall-mounted ON-OFF switch or optional

remote control.

The modesty panel mounted ON-OFF control

switch is located behind the control compart-

ment access panel, below the appliance front

glass enclosure panel. See

Figure 1.

WARNING: CHILDREN AND ADULTS

SHOULD BE ALERTED TO THE HAZARDS

OF HIGH SURFACE TEMPERATURES. USE

CAUTION AROUND THE APPLIANCE TO

AVOID BURNS OR CLOTHING IGNITION.

YOUNG CHILDREN SHOULD BE CARE-

FULLY SUPERVISED WHEN THEY ARE IN

THE SAME ROOM AS THE APPLIANCE.

WARNING: DO NOT PLACE CLOTHING

OR OTHER FLAMMABLE MATERIALS

ON OR NEAR THIS APPLIANCE.

AVERTISSEMENT: SURVEILLER LES

ENFANTS. GARDER LES VÊTEMENTS,

LES MEUBLES, L'ESSENCE OU AUTRES

LIQUIDES À VAPEUR INFLAMMABLES

LOIN DE L'APPAREIL.

WARNING: FAILURE TO COMPLY WITH

THE INSTALLATION AND OPERATING IN-

STRUCTIONS PROVIDED IN THIS DOCU-

MENT WILL RESULT IN AN IMPROP-

ERLY INSTALLED AND OPERATING AP-

PLIANCE, VOIDING ITS WARRANTY. ANY

CHANGE TO THIS APPLIANCE AND/OR

ITS OPERATING CONTROLS IS DANGER-

OUS. IMPROPER INSTALLATION OR USE

OF THIS APPLIANCE CAN CAUSE SERI-

OUS INJURY OR DEATH FROM FIRE,

BURNS, EXPLOSION OR CARBON MON-

OXIDE POISONING.

WARNING: B-VENT APPLIANCES ARE NOT

DESIGNED TO OPERATE IN NEGATIVELY

PRESSURED ENVIRONMENTS (PRESSURE

WITHIN THE HOME IS LESS THAN PRES-

SURES OUTSIDE). SIGNIFICANT NEGA-

TIVELY PRESSURED ENVIRONMENTS

CAUSED BY WEATHER, HOME DESIGN,

OR OTHER DEVICES MAY IMPACT THE

OPERATION OF THESE APPLIANCES.

NEGATIVE PRESSURES MAY RESULT IN

POOR FLAME APPEARANCE, SOOTING,

DAMAGE TO PROPERTY AND/OR SEVERE

PERSONAL INJURY. DO NOT OPERATE

THESE APPLIANCES IN NEGATIVELY PRES-

SURED ENVIRONMENTS. PROVIDING AD-

EQUATE VENTILATION TO THE APPIANCE

FOR COMBUSTION AIR WILL ELIMINATE A

NEGATIVE PRESSURE ENVIRONMENT.

* Each model has two burners. Each burner

contains one of these orifices.

The following table shows the units' gas ori-

fice size for the elevations indicated:

Figure 1

Control Compartment Access -

Millivolt Control Valve Shown

Maximum manifold pressure is 3.5 in. w.c.

(0.87 kPa) for natural gas and 10 in. w.c. (2.49

kPa) for LP/Propane gas.

Do not use these appliances if any part has

been under water. Immediately call a qualified,

professional service technician to inspect the

appliance and to replace any parts of the

control system and any gas control which

have been under water.

Ne pas se servir de cet appareil s'il a été plongé

dans l'eau, complètement ou en partie. Appeler

un technicien qualifié pour inspecter l'appareil

et remplacer toute partie du système de

contrôle et toute commande qui ont été plongés

dans l'leau.

Test gage connections are provided on the

front of the millivolt gas control valve (identi-

fied OUT for the manifold side and IN for inlet

pressure. A ¹⁄₈" NPT test gage connection is

provided on the electronic gas control valve

adjacent to the outlet to the main burner.

Minimum inlet gas pressure to these appli-

ances is 5.0 inches water column (1.24 kPa)

for natural gas and 11 inches water column

(2.74 kPa) for propane for the purpose of input

adjustment.

Maximum inlet gas supply pressure to these

appliances is 10.5 inches water column (2.61

kPa) for natural gas and 13.0 inches water

column (3.23 kPa) for propane.

The appliance must be isolated from the gas

supply piping system (by closing its individual

manual shut-off valve) during any pressure test-

ing of the gas supply piping system at test

pressures equal to or less than ¹⁄₂ psig (3.5 kPa).

Piezo Ignitor

Gas Valve

Modesty Panel

Control

Compartment

Access panel

ON/OFF

Switch

Hinge

ledoM

.oN

*ezisecifirO noitavelE

)sretem(teeF

.taN.porP

2-TSBE

2-FPBE

YABBE 44#55# 0054-0 )2731-0(

2-RCBE

2-LCBE 74#"50.0

The appliance and its individual shut-off valve must

be disconnected from the gas supply piping system

during any pressure testing of that system at pres-

sures in excess of ¹⁄₂ psig (3.5 kPa).

These appliances must not be connected to a

chimney or flue serving a separate solid fuel

burning appliance.

Any safety guard or screen removed for ser-

vicing the appliance must be replaced prior to

operating the appliance.

4NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Figure 2

Note: The piezo ignitor is located on the modesty panel - see Figure 1.

Remove the modesty panel carefully, so that

none of the wires become loose or discon-

nected. Now complete access to the gas con-

trol valve and its related controls is attainable.

To ease door closure, depress the catches to

place them in their retracted position, then

close the door.

Operation of millivolt and electronic gas con-

trol systems are different. Before lighting and

operating your appliance determine if you have

a millivolt or electronic appliance.

Refer to

Figure 1 on page 4

for access to the gas

control valve. Millivolt appliances will be fitted

with the gas control valve shown in

Figure 2

Appliances with electronic systems will be

fitted with the electronic valve shown in

Figure 3

. Familiarize yourself with the gas

control valve that your appliance uses.

Millivolt Appliances -

To light millivolt appliances refer to the de-

tailed lighting instructions found on

page 13

(English) and page 14

(French). Millivolt ap-

pliance lighting instructions may also be

found on the pull out lighting instruction

labels attached to the gas control valve.

Millivolt appliances are fitted with a burner ON/

OFF control switch (rocker switch). See

Figure

1 on page 3

for its location. Once the pilot is lit,

the ON/OFF rocker switch will control the appli-

ance ON/OFF operation. To operate: Toggle the

switch between its ON and OFF positions.

Figure 3

Honeywell Electronic

Gas Valve

ON/OFF Switch

Electronic

Gas Control

Valve

Inlet

Pressure

Port

Manifold Pressure Port

OFF

PSI

CONTROL

IGNITER

If your millivolt appliance is equipped with an

optional wall-mounted ON/OFF switch or re-

mote control kit and the pilot is lit, the appliance

main burner may be turned on and off with the

wall switch or remote control.

Electronic Appliances -

To light electronic appliances refer to the de-

tailed lighting instructions found in both En-

glish and French on

pages 15 and 16

of these

instructions respectively. Electronic appliance

lighting instructions may also be found on the

pull out lighting instruction labels attached to

the gas control valve.

Electronic appliances are fitted with a ON/OFF

burner control switch (rocker switch). See

Figure 1 on page 3

for its location. The elec-

tronic system will go through the whole light-

ing sequence automatically once the rocker

switch is toggled to the ON position.

If your electronic appliance is equipped with an

optional wall-mounted ON/OFF switch or re-

mote control kit the appliance main burner may

be turned on and off with the wall switch or

remote control.

TPTH TP TH

Variable Flame Height Adjustment

Manifold Pressure Port

Inlet Pressure Port

Main Gas

Control Knob

IN OUT

SIT Millivolt Gas Valve

Gas Controls/Control Compartment Access

The gas controls can be found behind the

control compartment access panel.

To open the control compartment access panel,

actuate the spring-loaded magnetic catches

securing the panel, by gently depressing the

outer top corners of the panel until the catches

"pop" the door free, allowing it to swing out and

down to open.

On millivolt systems, the piezo ignitor, Hi/Lo

flame adjustment knob, and pilot and main gas

ON/OFF control knob are located on the mod-

esty panel. On both millivolt and electronic

systems the gas valve is located behind the

modesty panel. Refer to

Figure 1.

Remove the bottom control compartment ac-

cess panel by compressing the spring-loaded

hinge pin on the left side until it disengages

from the left cabinet panel hole. Pull the panel

away from the fireplace.

Once the control compartment access panel

has been removed, the modesty panel can be

removed as follows: pull the bottom right

corner of the modesty panel out slightly to

disengage the snap-fit feature; lift the modesty

panel by the tab on the panel's right end, pull

the right end of the panel away from the

cabinet and then pull the panel diagonally out

of the left side cabinet panel slots. (In the

above procedure, reverse the words "left" and

"right" for EDCR-2 models).

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Outside Combustion Air Controls

Many appliances are equipped, when installed,

with an outside (make-up air) vent system

that is designed to provide the appliance with

outside make-up air for combustion when in

operation. The outside air control lever for

the outside air system is standard on all

appliances but should not be operated if the

complete system is not installed. Refer to

Figure 4

. When the complete outside air vent

system is installed, the installer will remove

the securing screw from the combustion air

control lever located on the right side (EBST-

2, EBPF-2 and EBCL-2), or left side (EBCR-2)

of the fireplace opening.

If the securing screw has not been removed and

you have reason to believe that you have a

complete outside air system, contact your dis-

tributor to have your appliance inspected for

the presence of the complete system. DO NOT

assume that you have this system in place.

WARNING: DO NOT OPERATE THE SHUTOFF

LEVER UNLESS A COMPLETE OUTSIDE

COMBUSTION AIR SYSTEM HAS BEEN IN-

STALLED WITH YOUR APPLIANCE.

Outside Air Control Lever

and Securing Screw Location

(EBST-2, EBPF-2 and EBCR-2 Units Shown)

Figure 4

To open the outside air shutter, open the

botttom control access panel, reach into the

gap between the firebox bottom and the

modesty panel, and pull the outside air con-

trol lever all the way out. The outside air

shutter should be fully open when the fire-

place is in use and completely closed when

the fireplace is not being used. Closing it

when not in use will prevent outside cold air

from entering the dwelling.

CAUTION: DO NOT TOUCH THE FRONT EN-

CLOSURE GLASS WITH YOUR HANDS WHILE

THE FIREPLACE IS IN USE.

WARNING: DO NOT USE ABRASIVE

CLEANERS. NEVER CLEAN THE GLASS

WHEN IT IS HOT.

Outside Air Control Lever with Stop Behind

Securing Screw

Outside Air Shutter in the

Closed Position

Control Compartment Access Panel

Venting Action and Safety Limit Operation

If you suspect that the appliance is not venting

properly, or you notice windows fogging or

sweating, you may want to conduct the fol-

lowing spillage test:

1 - Place unit in its normally-operated con-

dition, that is, with the glass enclosure pan-

els in place.

2 - Close all doors and windows in the

room. Turn on all exhaust fans in the house.

3 - Light the appliance.

4 - Wait 15 minutes.

5 - To check for venting action, start by

holding a smoke producing device within an

inch of one edge (side edge, not top or

bottom edge) of one glass enclosure panel.

The smoke should be drawn toward the edge

of the glass enclosure panel. Continue the

test by moving the smoke producing device

along the entire length of both side-edges of

the glass door. Repeat the test for all glass

enclosure panels.

6 - If the smoke is not drawn towards the

edges of the glass door turn off the appli-

ance and call a qualified service technican.

Variable Flame Height Adjustment

( Millivolt Appliances only)

1. All Millivolt appliances are equipped with a

variable gas control valve. Flame height for

these models may be adjusted through a range

between fixed low and high settings while the

appliance is in operation.

Adjust the flame height as desired after lighting

the appliance by rotating the variable adjust-

ment control knob located on the front of the

valve

(refer to Figure 2)

. (An extension is

provided to this knob so that the adjustment

may be made at the modesty panel.)

2. When lit for the first time, this appliance will

emit a slight odor for 14 hours. This is due to the

“burn-in” of internal paints and lubricants used

in the manufacturing process.

3. Keep lower control compartment clean by

vacuuming or brushing at least twice a year.

More frequent cleaning may be required due to

excessive lint from carpeting, bedding materi-

als, etc. It is important that control compart-

ments, burners and circulating air passage-

ways of the appliance be kept clean.

4. Always turn off gas to the pilot (millivolt

appliances) and let the unit cool down before

cleaning. Before re-lighting, refer to the light-

ing instructions in this manual. Lighting in-

structions may also be found on the pull out

lighting instruction labels attached to the

gas control valve.

5. Always keep the appliance area clear and

free from combustible materials, gasoline and

other flammable liquids.

6. Remember, Millivolt appliances have a con-

tinuous burning pilot flame. Exercise caution

when using products with combustible vapors.

7. Clean the front glass enclosure only when

necessary and when the unit is cool. Wipe

surface with clean, dampened, soft cloth. Fol-

low with dry, soft towel as desired. Take care

not to scratch the glass surface.

6NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Manual-Reset Safety Limit Switch

This appliance is equipped with a manual-

reset blocked flue safety limit switch. Refer to

Figure 5

for its location. If, during appliance

operation, the flame goes out (independently

of the burner on/off wall switch), it may be due

to the operation of this safety limit switch.

First allow the appliance to cool, then reset

the safety switch by pushing the red reset

button on it.

A - To access the blocked flue safety switch

when top radiant panel is not covered with

non-combustible material:

1 - Lift up and remove top radiant panel/

eyebrow assembly on the control side of

unit.

2 - Reach between the cabinet side and the

firebox side wall and locate the blocked flue

safety switch.

3 - Push the red reset button on the switch.

The applilance should then relight and remain

lit. If this does not occur, turn off the appli-

ance and call a qualified service technician.

Figure 5

Maintenance

The appliance and venting system should be

thoroughly inspected before initial use and at

least annually by a qualified service techni-

cian. However, more frequent periodic inspec-

tions and cleanings should be performed by

the homeowner. Homeowner must contact a

qualified service technician at once if any

abnormal condition is observed.

Refer to the maintenance schedule for mainte-

nance tasks, procedures, periodicity and by

whom they should be performed. Always

verify proper operation of the appliance after

servicing.

IMPORTANT: TURN OFF GAS AND ANY ELEC-

TRICAL POWER BEFORE SERVICING THE

APPLIANCE.

WARNING: NEVER OPERATE THE APPLI-

ANCE WITHOUT THE GLASS ENCLOSURE

PANELS IN PLACE AND SECURE. DO NOT

OPERATE APPLIANCE WITH FRONT GLASS

CRACKED, BROKEN OR MISSING. REPLACE-

MENT MUST BE DONE BY A LICENSED OR

QUALIFIED SERVICE TECHNICIAN.

Front Glass Enclosure Panel, Removal

and Installation.

These fireplaces are designed to operate only

with the glass enclosure panels properly in-

stalled. Generally the glass enclosure panels

should not be removed except to gain access

to the components within the firebox, and the

appliance may only be operated without the

front glass enclosure panel in place for very

brief periods of time during initial appliance

checkout and adjustment.

During this appliance checkout and adjustment

period, a potential safety hazard exists - EXER-

CISE EXTREME CAUTION to prevent the occur-

rence of any burn injuries from the exposed

flames or hot surfaces. Also note, that while the

front glass enclosure panel (or any of the panels)

is removed, the flame appearance will appear to

be smaller than normal.

B - To access the blocked flue safety switch

when top radiant panel is covered with non-

combustible material:

Note: This procedure should only be performed

by a qualified service technician.

1 -Lower bottom hinged panel on the con-

trol side of the fireplace. Remove the mod-

esty panel and glass enclosure panel as

described on page 8, under "Remove the

front glass enclosure panel as follows:",

Steps 2, 3, 4, 5 and 6.

2 -Remove the side baffle securing screws

(5) and then remove the baffle.

3 -Remove the safety switch bracket secur-

ing screws (2), and pull the switch/bracket

assembly through the side panel slot.

4 -Push the red reset button on the switch.

5 -Reinstall the switch/bracket assembly.

6 -Reinstall the side baffle.

7 -Reinstall front glass door.

8 -Raise the bottom hinged panel.

The appliance should then relight and remain

lit. If this does not occur, check unit for a

blocked flue condition.

SAFETY SWITCH LOCATION (EBCL-2 SHOWN)

EBST-2 and EBPF-2 Safety Switch Location Also as Shown; EBCR-2 Location

on Left End of Fireplace, EBBAY Location on The Rear of Fireplace.

MANUALLY-RESET

SAFETY LIMIT SWITCH

FIREBOX SIDE BAFFLE

FIREBOX SIDE BAFFLE SECURING SCREW

FIREBOX BOX

SIDE WALL

CABINET SIDE WALL

TOP RADIANT PANEL

AND EYEBROW

SAFETY SWITCH

BRACKET SECURING SCREW

WARNING: HANDLE THE GLASS WITH EX-

TREME CARE! TEMPERED GLASS IS SUS-

CEPTIBLE TO DAMAGE (SCRATCHES, FOR

EXAMPLE) – HANDLE GLASS DOOR

(GLASS ENCLOSURE PANEL) GENTLY

WHILE REINSTALLING IT.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Periodically (After the Burning Season)

Maintenance Task Accomplishing Person Procedure

Cleaning Firebox Interior

Check Flame Patterns and Flame Height

Checking Vent System

Cleaning Glass Enclosure Panels

Homeowner

Carefully remove logs, vermiculite and black and

gray ceramic fiber chunks. Vacuum out interior of

the firebox. Clean firebox walls and log grate.

Replace logs, vermiculite and black and gray ce-

ramic fiber chunks as detailed on

page 8

Maintenance Task Accomplishing Person Procedure

Inspecting/Cleaning Burner, Logs

and Controls

Check Flame Patterns and Flame Height

Inspecting/Cleaning Pilot Burner and the Two

Main Burners

Checking Vent System

Appliance Checkout

Qualified Service Technician

Inspect valve and ensure it is properly operat-

ing. Check piping for leaks. Vacuum the con-

trol compartment, fireplace logs and burner

area.

Refer to

Figure 8 on page 8

and verify that the

flame pattern and height displayed by the

appliance conforms to the picture. Flames

must not impinge on the log set.

Refer to

Figure 1 on page 8 (SIT) or Figure 12

on page 9 (Honeywell)

. Remove any surface

build-up on pilot and burner assembly. Clean the

pilot nozzles, ignitor/flame rod and hood with a

soft brush. Ensure the pilot flame engulfs the

flame sensor as shown.

Inspect the vent system at the top and at the

base (within the firebox) for signs of blockage

or obstruction. Look for any signs of disloca-

tion of the vent components.

Perform the appropriate appliance checkout

procedure detailed in this manual.

Maintenance Schedule

Annually (Before the onset of the Burning Season)

Clean as necessary following the directions

provided in this manual. DO NOT TOUCH OR

CLEAN GLASS WHILE IT IS HOT.

Inspect the vent system at the top and at the

base (within the firebox) for signs of block-

age or obstruction. Look for any signs of

dislocation of the vent components.

Refer to

Figure 8 on page 8

and verify that

the flame pattern and height displayed by the

appliance conforms to the picture. Flames

must not impinge on the log set.

8NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Refer to

Figure 6

and remove the front glass

enclosure panel as follows:

1. Remove the top bustle, and the top louver

assembly or radiant panel. Then remove the

bottom bustle.

2. Open the control compartment access panel.

To open the control compartment access panel,

actuate the spring-loaded magnetic catches

securing the panel, by gently depressing the

outer top corners of the panel until the catches

"pop" the door free, allowing it to swing out and

down to open.

3. Remove the bottom control compartment

access panel by compressing the spring-loaded

hinge pin on the left side until it disengages

from the left cabinet corner post hole. Pull the

panel away from the fireplace.

4. Once the control compartment access panel

has been removed, the modesty panel can be

removed as follows: pull the bottom right

corner of the modesty panel out slightly to

disengage the snap-fit feature; lift the modesty

panel by the tab on the panel's right end, pull

the right end of the panel away from the

cabinet and then pull the panel diagonally out

of the left side cabinet panel slots. (In the

above procedure, reverse the words "left" and

"right" for EBCR-2 models).

Remove the modesty panel carefully, so that

none of the wires become loose or discon-

nected. Now complete access to the gas control

valve and its related controls is attainable.

4. Reinstall the modesty panel by inserting the

tongues on the left side of it into the slots on

the left side cabinet panel. Swing the right side

of the modesty panel towards the unit. Engage

the hook on the right side of the modesty panel

with the right side cabinet panel slot. Gently

press the bottom right corner of the modesty

panel to engage the snap-fit feature.

(The left and right designations used here are

reversed in EBCR-2 applications.)

5. Reinstall the bottom control compartment

access panel by inserting the right side locat-

ing pin into the right side cabinet panel and

then the left side spring-loaded pin into the left

side cabinet panel.

6. Reinstall the top and bottom bustle, and the

top louver assembly or radiant panel.

Burner Adjustments

Note -

The air shutter for the burner primary air

opening is factory-set. Do not adjust the fac-

tory-set position. The factory-set position is

shown in Figure 7.

THE GLASS DOORS OF THIS APPLIANCE MUST

ONLY BE REPLACED AS A COMPLETE UNIT AS

PROVIDED BY THE MANUFACTURER. DO

NOT ATTEMPT TO REPLACE BROKEN,

CRACKED OR CHIPPED GLASS SEPARATELY.

5. Locate the latch at the top of the control

compartment. To disengage the latch from the

bottom vee-flange of the glass enclosure panel,

reach for the handle located towards the back

of the latch and pull the handle down towards

the front of the unit.

6. Swing the bottom of the door out and raise

it slightly to lift the top flange of the door frame

away from the appliance.

To install the front glass enclosure panel,

proceed as follows:

1. Visually inspect the gasket on the backside

of the panel. The gasket surface must be clean,

free of irregularities and seated firmly.

2. Position the glass enclosure panel in front

of the firebox opening at a 45 degree angle and

engage the top flange over the lip at the top of

the firebox opening.

3. Swing the glass enclosure panel down and

back. Ensure the gasket seats evenly as the

panel draws shut. Engage the Vee-flange at

the bottom of the panel with the latch and then

close the latch to secure the panel.

Figure 7

*Note - Do Not Adjust the Factory-Set Position.

Each of the two air shutters (one for each burner) are

open the amount shown in the table, below.

Figure 6

Glass

Enclosure

Panel

Latch

Lower Compartment Door and Hinge

Front Glass

Enclosure Panel

Firebox Floor

Bottom Vee-flange

(Glass Enclosure

Panel Frame)

Top Flange

(Glass Enclosure

Panel Frame)

Modesty Panel

EBST-2 SHOWN

Orifice

*Air Shutter

Opening Burner

Venturi

Tube

RENRUBNIAM

GNITTESRETTUHSYROTCAF

sledoM saGlarutaN sehcni )mm(

enaporP saG sehcni )mm(

2-TSBE 2-FPBE 2-RCBE 2-LCBE YABBE

61/1)5.1(61/5)8(

WARNING: DO NOT ATTEMPT TO SUBSTI-

TUTE THE MATERIALS USED ON THESE

DOORS, OR REPLACE CRACKED OR BRO-

KEN GLASS WITH ANY MATERIALS OTHER

THAN THOSE PROVIDED BY THE APPLI-

ANCE MANUFACTURER.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Log Placement

WARNING: LOG SET GETS VERY HOT

AND WILL REMAIN HOT UP TO ONE

HOUR AFTER GAS SUPPLY IS TURNED

OFF. HANDLE ONLY WHEN LOG SET IS

COOL. TURN OFF ALL GAS TO THE

APPLIANCE BEFORE INSTALLING THE

GRATE AND LOG SET.

WARNING: THIS APPLIANCE IS NOT DE-

SIGNED TO BURN WOOD. ANY ATTEMPT

TO DO SO COULD CAUSE IRREPARABLE

DAMAGE TO YOUR APPLIANCE AND

PROVE HAZARDOUS TO YOUR SAFETY.

WARNING: THE SIZE AND POSITION OF

THE LOG SET WAS ENGINEERED TO GIVE

YOUR APPLIANCE A SAFE, RELIABLE

AND ATTRACTIVE FLAME PATTERN. ANY

ATTEMPT TO USE A DIFFERENT LOG SET

IN THE FIREPLACE WILL VOID THE WAR-

RANTY AND WILL RESULT IN INCOM-

PLETE COMBUSTION, SOOTING, AND

POOR FLAME QUALITY.

Install the unitized log set:

a - The bottom of the log set is notched to

accommodate the pilot.

b - Place the log set so that the four inner

notches on the underside of the log set

fit over the four risers located on the burner

ends.

See Figure 9

. This procedure is accom-

plished primarily by feel, as the log set masks

the burner risers as it is being installed.

c - As a final check for correct log set place-

ment, check that the four outer notches on the

underside of the log set fit over the burner

tines as indicated in figure 6.

The log set, with one bag of vermiculite, is

packaged in a carton located within the firebox

area. One plastic bag of glowing embers and

one plastic bag of decorative volcanic stone is

located in the bottom compartment. Refer to

the following information and

Figures 8 and 9

for detailed placement instructions for the

logs, vermiculite, glowing embers (rockwool)

and decorative volcanic stone.

Figure 8

also

shows a typical flame pattern for this particu-

lar appliance.

Install the vermiculite, decorative volcanic

stone and glowing embers (rockwool):

Spread vermiculite on the simulated brick floor

of the firebox around the burners to simulate

ashes. Maintain a ¹⁄₂ in. gap between the bot-

tom of the horizontal grate section and the top

of the pile of vermiculite. Sprinkle the decora-

tive volcanic stone on the vermiculite as shown

Figure 8.

Place a few dime-sized pieces of rockwool on

the pan burner in front of the burned out area

on both sides of the log set. The pieces of

rookwool may touch one another, but should

not overlap each other.

Millivolt Appliance Checkout

The pilot flame should be steady, not lifting or

floating. Flame should be blue in color with

traces of orange at the outer edge.

The top ³⁄₈" (10 mm) at the pilot generator

(thermopile) and the top ¹⁄₈" min (tip) of the

quick drop out thermocouple should be en-

gulfed in the pilot flame. The flame should

project 1" (25 mm) beyond the hood at all three

ports. See

Figure 11.

To light the burner, refer to the lighting in-

structions on

pages 14 and 15.

Figure 8

Note: If the burners have been removed for any

reason, reinstall them as shown in Figure 10.

Figure 10

Figure 9

FRONT OF FIREPLACE

REAR BURNER

FRONT BURNER

Outer Log

Notch Location

FIREBOX SUBFLOOR

Outer

Log Notch

Location

Outer Log

Notch Location Outer Log

Notch Location

Riser - Inner Log

Notch Location

LOG NOTCH LOCATION RELATIVE TO BURNER

Pilot Assembly

Riser - Inner Log

Notch Location

BURNER POSITIONING

REAR BURNER

FRONT BURNER

PILOT

BURNER

Note: The burners are not identical. Position them so

that the circular burner ports run as shown. Note

especially the vertical run of ports relative to the pilot

burner. Bracket A on the rear burner will interfere

with the pilot burner if an attempt is made to install

the rear burner in the front burner’s position.

BRACKET A BURNER

PORTS

NOTE: INSTALL REAR BURNER FIRST,

THEN FRONT BURNER.

Glowing Embers (Rockwool) Decorative Volcanic StoneVermiculite

10 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Electronic Appliance Checkout

To light the burner, refer to the lighting instruc-

tions on

page 15 and 16

. Ensure the ignitor lights

the pilot. The pilot flame should engulf the flame

sensor as shown in

Figure 12

With proper care and maintenance, your appli-

ance will provide many years of enjoyment. If you

should experience any problem, first refer to the

trouble shooting guide in this manual. If problem

persists, contact your Lennox distributor.

WIRING DIAGRAMS

Wiring diagrams are provided here for refer-

ence purposes only. This information is also

provided on schematics attached directly to

the appliance on a pullout panel located within

the control compartment.

CAUTION: LABEL ALL WIRES PRIOR TO DIS-

CONNECTION WHEN SERVICING CONTROLS.

WIRING ERRORS CAN CAUSE IMPROPER AND

DANGEROUS APPLIANCE OPERATION.

WARRANTY

Your gas appliance is covered by a limited

twenty year warranty. You will find a copy of

the warranty accompanying this manual.

Please read the warranty to be familiar with its

coverage.

Retain this manual. File it with your other docu-

ments for future reference.

REPLACEMENT PARTS

A complete parts list is found at the end of this

manual. Use only parts supplied from the

manufacturer.

Normally, all parts should be ordered through

your Lennox distributor or dealer. Parts will be

shipped at prevailing prices at time of order.

When ordering repair parts, always give the

following information:

1. The model number of the appliance.

2. The serial number of the appliance.

3. The part number.

4. The description of the part.

5. The quantity required.

6. The installation date of the appliance.

If you encounter any problems or have any

questions concerning the installation or appli-

cation of this system, please contact your dis-

tributor, or Lennox directly:

LENNOX HEARTH PRODUCTS

1110 West Taft Avenue

Orange, CA 92865

PRODUCT REFERENCE INFORMATION

We recommend that you record the following important information about your fireplace. Please

contact your Lennox dealer for any questions or concerns. For the number of your nearest Lennox

dealer, please call 800-731-8101

Your Fireplace's Model Number _______________________________________

Your Fireplace's Serial Number ________________________________________

The Date On Which Your Fireplace Was Installed __________________________

The Type of Gas Your Fireplace Uses ___________________________________

Your Dealer's Name_________________________________________________

Figure 11

MILLIVOLT

Thermocouple

Hood Ignitor Rod

³⁄₈" Min

(9 mm)

Thermopile

Pilot

Nozzels

ELECTRONIC

Proper Flame

Adjustment

Pilot

Nozzle

3/8 To 1/2 Inch

(9 mm to 13 mm)

Ground

Electrode

Flame Rod

Hot Surface

Igniter

Thermopile

TP TH

White

Black

Millivolt Wiring Diagram

If any of the original wire as supplied must be replaced,

it must be replaced with Type AWM 105°C – 18 GA. wire.

*OPTIONAL WALL-MOUNTED ON/OFF

SWITCH OR OPTIONAL THERMOSTAT

OR OPTIONAL REMOTE RECEIVER

*Turn the appliance-mounted ON/OFF burner control

switch to the OFF position if an optional

control switch is installed.

Factory Wired

Field Wired

Schematic Representation Only

APPLIANCE-MOUNTED ON/OFF SWITCH

LIMIT SWITCH

1. If any of the original wire as supplied must be replaced,

1. it must be replaced with Type AWM 105°C – 18 GA.

wire.

2. 120V, 60Hz – Less than 3 amps.

Junction Box

Transf.

120 V.

24 V

Factory Wired Field Wired

Electronic Wiring Diagram (Honeywell)

120

VAC.

Gas Valve

APPLIANCE-MOUNTED ON/OFF SWITCH

IGNITER

PILOT

ASSEMBLY

Outlet Box Green

Ground Screw

Hot side of Outlet

Schematic Representation Only

*ON/OFF Switch (Integral

with Gas Valve)

White Wire

To Opposite

Side

**OPTIONAL WALL SWITCH

OR OPTIONAL THERMOSTAT

OR OPTIONAL REMOTE

RECEIVER

*Leave the ON/OFF switch, which is integral

with the gas valve, in the ON position.

**Turn the appliance-mounted ON/OFF burner control switch to

the OFF position if an optional control switch is installed.

LIMIT SWITCH

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Arch Door Kits

Two types of arch door kits are available for

the Multi-Open Series. Both types of kits are

easy to install and do not require hardware

to attach them to the standard door frame.

These kits can be retrofitted to previously

installed Multi-Open Series appliances. The

decorative arch kits can not be used in

conjunction with the screen panel kit.

ACCESSORY COMPONENTS

Door Frame Kits

A decorative door frame kit is available for

use with these appliances. The DTK is de-

signed to attach directly to the front face of

the appliance at its extreme edges. The DTK

provides a picture frame finish for the appli-

ance. The door frame kit can be retrofitted

onto previously installed appliances.

ON/OFF Wall Switch Kit 85L87 FWSK

ON/OFF Wall Switch Kit

The ON/OFF wall switch kit may be used to

control the operation of the fireplace burner as

an alternative to the modesty panel mounted

ON-OFF switch. Install the ON/OFF wall switch

in a convenient location near the fireplace.

Remote Control System (Standard) H0249 RCL

Standard Remote Control System

(Model RCL)

The Model RCL (Standard) Remote Control

System, features a simplistic on/off control

function for the fireplace. This model includes

a hand-held transmitter, a remote receiver with

wall-mount coverplate and all hardware re-

quired to install the unit. The remote receiver

can be wall or hearth mounted.

The transmitter has ON and OFF functions that

are activated by pressing either button on the

face of the transmitter. When a button on the

transmitter is pressed, a signal light illuminates

briefly to verify that a signal has been sent.

The Model RCL is designed to operate with all

millivolt ignition systems, as well as electronic

ignition systems. It may be installed with use

for either natural or propane gas appliances.

The RCL offers ease of installation and allows

you to execute on-off commands to the fire-

place effortlessly with one simple motion.

The Model RCL comes complete with detailed

operating instructions.

stiKemarFrooD STESFOREBMUNDNA.ONLEDOM/.ONGOLATAC

tinU ledoM .oN

hsiniFssarBdehsiloPhsiniFsselniatSdehsurB

ediw.ni42rof rooDssalG ediw.ni04rof rooDssalG ediw.ni42rof rooDssalG ediw.ni04rof rooDssalG

34L88 2-BP42KTD 54L88 2-BP04KTD 96L09 SB42KTD 17L09 SB04KTD

2-TSBE-2 - 2

2-FPBE12 1 2

2-RCBE 2-LCBE 11 1 1

YABBE21 2 1

-stiKrooDhcrA YTITNAUQDNA.ONLEDOM/.ONGOLATAC

tinU ledoM .oN

hsiniFssarBdehsiloPhsiniFsselniatSdehsurB

ediw.ni42rof rooDssalG ediw.ni04rof rooDssalG ediw.ni42rof rooDssalG ediw.ni04rof rooDssalG

73L18 BPC42KDA 53L18 BPC04KDA 17L89 SBC42KDA 96L89 SBC04KDA

2-TSBE-2- 2

2-FPBE12 1 2

2-RCBE 2-LCBE 11 1 1

YABBE21 2 1

12 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Polished Brass and Brushed Stainless Hood

Kits

Attractive hoods are available in two styles to be

used on the Multi-Open Series appliances. These

hoods are designed to be fitted to the glass

viewing sides of the appliance. In addition to

providing an aesthetically pleasing appearance

to your appliance installation, the hood reduces

heat effects to decorative mantles and finish

materials located above the fireplace opening.

The hood kit replaces the standard hood that

comes with these appliances and snaps into

place. These kits can be retrofitted to previously

installed appliances.

Charcoal Finish Louvers Kits

Decorative louvers are available for use with all Multi-Open Series appliances. These louvers

are designed to replace the standard radiant panels that are provided with the appliance. These

kits include a charcoal finish top 3-piece assembly and a bottom 3-piece assembly. These kits

can be retrofitted to previously installed appliances.

ACCESSORY COMPONENTS CONTINUED

Outside Air Kits Models FOAK-4 and FOAK-4LD

Outside Air kits are available with duct (FOAK-4)

and without duct (FOAK-4LD) for use if outside

combustion air is required or desired. If model

FOAK-4LD is used it must be used in conjunction

with locally purchased, non-combustible Class 1

or Class 0 flexible duct.

Outside Combustion Air Kits

(with duct) 81L87 FOAK-4

(without duct) 81L88 FOAK-4LD

Deluxe Remote Control System

(Model RCL-T)

The Model RCL-T (Deluxe) Remote Control

System has all of the features of the standard

system along with an added easy to read LCD

screen which presents access to many en-

hancements, including; battery power level in-

dicator, timer, mode of operation, thermostatic

display including room temperature in either

metric of English units, flame indicator and

clock. Fully programmable, the Model RCL-T

allows for virtual command over nearly all

operational and temperature variables, using

the hand held remote control transmitter.

The Model RCL-T (Deluxe) remote control sys-

tem is installed in the same manner as the

standard system, may be operated with elec-

tronic and millivolt systems with either natural

or propane gas. The RCL-T comes complete

with detailed operating instructions.

Remote Control System (Deluxe) H0251 RCL-T

stiKylbmessArevuoLhsiniFlaocrahC

)ylbmessAmottoBeceip-3dnapoTeceip-3( .ONLEDOM/.ONGOLATAC STESFOREBMUNDNA

tinU ledoM .oN

hsiniFlaocrahC

ediw.ni42rof rooDssalG ediw.ni04rof rooDssalG

32L88 2-C42RVL 52L88 2-C04RVL

2-TSBE-2

2-FPBE12

2-RCBE 2-LCBE 11

YABBE21

stiKdooH STESFOREBMUNDNA.ONLEDOM/.ONGOLATAC

tinU ledoM .oN

hsiniFssarBdehsiloPhsiniFsselniatSdehsurB

ediw.ni42rof rooDssalG ediw.ni04rof rooDssalG ediw.ni42rof rooDssalG ediw.ni04rof rooDssalG

82K89 BP42BE 86K69 BP04BE 74L88 SB42BE 05L88 SB04BE

2-TSBE-2 - 2

2-FPBE12 1 2

2-RCBE 2-LCBE 11 1 1

YABBE21 2 1

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

ACCESSORY COMPONENTS CONTINUED

Polished Brass and Brushed Stainless

Louvers Kits

Decorative louvers are available for use with all

Multi-Open Series appliances. These louvers

are designed to replace the standard radiant

panels that are provided with the appliance.

These kits include a top 3-piece assembly and

a bottom 3-piece assembly. They provide a

touch of elegance to any Multi-Open Series

appliance. These kits can be retrofitted to

previously installed appliances.

Touch-Up Paint (Charcoal) Kit 90L74 TPK-C

Touch-Up Paint Kit

Repair of minor scratches and discoloration of

the appliance charcoal painted cabinet sur-

faces may be accomplished with the touch-up

paint kit.

2-Piece Polished Brass and Brushed

Stainless Louvers Kits

Decorative louvers are available for use with all

Multi-Open Series appliances. These louvers

are designed to replace either the middle char-

coal louver of each set or the charcoal louver

in each set closest to the glass door. These kits

include two narrow louvers. They provide a

touch of elegance to any Multi-Open Series

appliance. These kits can be retrofitted to

previously installed appliances.

Screen Panel Kit

24 inch Wide Glass Door 98K74 HG24

40 inch Wide Glass Door 96K32 HG40

Screen Panel Kit

An optional screen panel can be installed on the

Multi-Open Series doors. These screen panels

are easy to install. These kits can be retrofitted to

previously installed appliances. The screen panel

kits can not be used in conjunction with either of

the arch door kits or door frame kits.

Twin-Pane Door Trim Kits

Polished Brass - 40 inch 20M83 TPDK-40PB

Brushed Stainless - 40 inch 20M86 TPDK-40BS

Polished Brass and Brushed Stainless

Twin-Pane Door Trim Kits

Two types of twin-pane door trim kits are

available for the Multi-Open Series (polished

brass or bruhed stainless). Both types of kits

are easy to install and do not require hardware

to attach them to the standard glass door

frame. Only the 40 inch glass door frame can

be fitted with these kits. The decorative twin-

pane door trim kits can not be used in

conjunction with the screen panel kit.

)eceip-2(stiKrevuoL STESFOREBMUNDNA.ONLEDOM/.ONGOLATAC

tinU ledoM .oN

hsiniFssarBdehsiloPhsiniFsselniatSdehsurB

ediw.ni42rof rooDssalG ediw.ni04rof rooDssalG ediw.ni42rof rooDssalG ediw.ni04rof rooDssalG

40L69 BP42RVL2 60L69 BP04RVL2 80L69 SB42RVL 01L69 SB04RVL

2-TSBE-2- 2

2-FPBE121 2

2-RCBE 2-LCBE 11 1 1

YABBE21 2 1

)ylbmessAmottoBeceip-3dnapoTeceip-3(stiKylbmessArevuoL STESFOREBMUNDNA.ONLEDOM/.ONGOLATAC

tinU ledoM .oN

hsiniFssarBdehsiloPhsiniFsselniatSdehsurB

ediw.ni42rof rooDssalG ediw.ni04rof rooDssalG ediw.ni42rof rooDssalG ediw.ni04rof rooDssalG

72L88 2-BP42RVL 92L88 2-BP04RVL 13L88 SB42RVL 33L88 SB04RVL

2-TSBE-2- 2

2-FPBE121 2

2-RCBE 2-LCBE 11 1 1

YABBE21 2 1

14 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

LIGHTING INSTRUCTIONS – MILLIVOLT GAS VALVE

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION

MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

FOR YOUR SAFETY READ BEFORE LIGHTING

A. This appliance has a pilot which must be lighted with a piezo

ignitor. When lighting the pilot, follow these instructions

exactly.

B. BEFORE OPERATING smell all around the appliance area for

gas. Be sure to smell next to the floor because some gas is

heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•Extinguish any open flame.

•Open windows.

•Do not light any appliance.

•Do not touch any electrical switches.

TO TURN OFF GAS TO APPLIANCE

1. Turn remote wall switch “OFF.” The pilot will remain lit for

normal service.

2. For complete shutdown, turn remote wall switch to “OFF.”

3. Access the lower control compartment.

4. Depress gas control knob slightly and turn clockwise

to “OFF.” Do not force.

5. Close lower control compartment.

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above on this page.

2. Access the lower control compartment.

3. Turn remote wall switch to “OFF.”

4. Verify main line shut-off valve is open.

5. Push in gas control knob slightly and turn clockwise

to “OFF.”

6. Wait five (5) minutes to clear out any gas. If you then smell gas,

STOP! Follow “B” in the safety information above on this page. If you

do not smell gas, go to the next step.

7. Push in gas control knob slightly and turn counterclockwise

to “PILOT.”

8. Push in control knob all the way and hold in. Immediately light the

pilot by triggering the spark ignitor (pushing the button) until pilot

lights. Continue to hold the control knob in for about 1 ¹⁄₂ minutes

after the pilot is lit. Release knob and it will pop back up. Pilot should

remain lit. If it goes out, repeat steps 5 through 8.

•If knob does not pop up when released, stop

and immediately call your service technician

or gas supplier.

•If pilot will not stay lit after several

tries, turn the control knob to “OFF”

and call your service technician or

gas supplier.

9. Turn gas control knob counterclockwise

to “ON.”

10. Close lower control compartment.

•Do not use any phone in your building.

•Immediately call your gas supplier from a neighbor’s phone.

•If your gas supplier cannot be reached, call the fire depart-

ment.

C. Use only your hand to push in or turn the gas control knob.

Never use tools. If the knob will not push in or turn by hand,

do not try to repair it, call a qualified service technician. Force

or attempted repair may result in a fire or an explosion.

D. Do not use this appliance if any part has been under water.

Immediately call a qualified service technician to inspect the

appliance and to replace any part of the control system and

any gas control which has been under water.

Note: Knob cannot be turned from “PILOT” to “OFF”

unless the knob is pushed in slightly. Do not force.

TPTH TP TH

OUT

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

INSTRUCTIONS D’ALLUMAGE – VANNE GAZ MILLIVOLT

INSTRUCTIONS D'ALLUMAGE

AVERTISSEMENT : SI VOUS NE SUIVEZ PAS CES INSTRUCTIONS À LA LETTRE, IL POURRAIT S’EN SUIVRE UN INCENDIE OU UNE

EXPLOSION CAUSANT DES DOMMAGES MATÉRIELS, DES BLESSURES CORPORELLES OU MÊME DES PERTES DE VIE.

POUR VOTRE SÉCURITÉ, LISEZ CES INSTRUCTIONS AVANT L’ALLUMAGE

A. Cet appareil est muni d’une veilleuse qui doit être allumée avec un

allumeur piézo-électrique. Lorsque vous allumez la veilleuse, suivre

exactement ces instructions.

B. AVANT L’ALLUMAGE: Assurez-vous que vous ne détectez aucune

odeur de gaz autour de l’apareil ainsi que près du sol; certains gaz, étant

plus lourds que l’air, descendent au niveau du sol.

VOICI CE QUE VOUS DEVEZ FAIRE SI VOUS DÉCELEZ UNE ODEUR

DE GAZ:

•Éteignez toute flamme visible.

•Ouvrez les fenêtres.

•N’allumez aucun appareil.

•Ne touchez à aucun commutateur électrique.

•Ne vous servez d’aucun téléphone dans votre édifice.

•Appelez immédiatement votre compagnie de gaz en utilisant le téléphone

du voisin.

•S’il vous est impossible de contacter votre compagnie de gaz, appelez

le service des incendies.

C. N’utilisez que votre main pour manipuler le bouton de réglage du gaz.

N’utilisez jamais d’outils. Si le bouton refuse de tourner ou de bouger,

n’essayez pas de le réparer. Communiquez immédiatement avec un

technicien de service qualifié. Toute tentative pour le forcer ou le

réparer, risquerait de provoquer un incendie ou une explosion.

D. Ne vous servez pas de cet appareil si l’un de ses éléments a été

immergé dans l’eau. Appelez immédiatement un technicien compétent

pour faire inspecter l’appareil et remplacer toute pièce du système de

réglage ou commande du gaz qui a été sous l’eau.

1. Tournez l’interrupteur mural à la position d’arrêt “OFF”. La veilleuse

restera allumée jusqu’au retour du service normal.

2. Pour une fermeture complète, tournez l’interrupteur mural à la

position d’arrêt “OFF”.

3. Ouvrez le compartiment de contrôle du bas.

POUR FERMER LE GAZ QUI ALIMENTE L’APPAREIL

4. Enfoncez légèrement le bouton de réglage du gaz et tournez-le dans

le sens des aiguilles d’une montre jusqu’à la position

d’arrêt “OFF”. Ne forcez pas le bouton.

5. Fermez le compartiment de contrôle du bas.

8. Enfoncez le bouton de réglage jusqu’au fond et gardez-le enfoncé.

Allumez immédiatement la veilleuse en déclenchant l’allume-gaz à

étincelle (en poussant le bouton) jusqu’à ce que la veilleuse

s’enflamme. Continuez de tenir le bouton de réglage enfoncé

pendant environ 90 secondes après l’allumage de la veilleuse.

Relâchez le bouton et il sortira subitement. La veilleuse devrait

rester allumée. Si elle s’éteint, répétez les étapes 5 à 8

inclusivement.

• Si le bouton ne sort pas automatiquement après avoir été relâché,

arrêtez immédiatement et téléphonez

à votre technicien de service ou à

votre fournisseur de gaz.

• Si la veilleuse refuse de rester

allumée après plusieurs tentatives,

tournez le bouton de réglage jusqu’à

sa position d’arrêt “OFF” et

téléphonez à votre technicien de

service ou à votre fournisseur de gaz.

9. Tournez le bouton de réglage du gaz en sens inverse des aiguilles

d’une montre jusqu’à sa position de marche “ON”.

10. Fermez le compartiment de contrôle du bas.

11. Au besoin, rebrancher l’appareil au courant électrique et remettre

l’interrupteur du brûleur principal à la position “ON” ou régler le

thermostat à la température désirée.

12. Si l’appareil ne fonctionne pas, suivre les instructions intitulées

“Pour fermer le gaz qui alimente l’appareil” et appeler un

technicien ou le fournisseur de gaz.

Remarque: Il est impossible de tourner le bouton de “PILOT” à “OFF” à

moins qu’il ne soit légèrement enfoncé. Ne le forcez pas.

6. Attendez cinq (5) minutes pour l’evacuation du gaz. Si vous décelez

une odeur de gaz, ARRÊTEZ ! Retournez au point “B” des consignes

de sécurité au verso de cette plaque. Si vous ne remarquez aucune

odeur de gaz, passez à l’étape suivante.

7. Enfoncez légèrement le bouton de réglage du gaz et tournez-le en

sens inverse des aiguilles d’une montre jusqu’à la position de

veilleuse “PILOT”.

1. ARRÊTEZ! Lisez les consignes de sécurité au verso de cette plaque.

2. Ouvrez le compartiment de contrôle du bas.

3. Tournez l’interrupteur mural à la position d’arrêt “OFF”.

4. Assurez-vous que la soupape d’arrêt de la canalisation principale est

ouverte.

5. Enfoncez légèrement le bouton de réglage du gaz et tournez-le dans

le sens des aiguilles d’une montre jusqu’à la position

d’arrêt “OFF”.

TPTH TP TH

OUT

16 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION

MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

A. When lighting the appliance, follow these instructions

exactly.

B. BEFORE OPERATING smell all around the appliance area

for gas. Be sure to smell next to the floor because some

gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•Extinguish any open flame.

•Open windows.

•Do not light any appliance.

•Do not touch any electrical switches.

•Do not use any phone in your building.

FOR YOUR SAFETY READ BEFORE LIGHTING

•Immediately call your gas supplier from a neighbor’s

phone.

•If your gas supplier cannot be reached, call the fire

department.

C. Use only your hand to turn the gas control lever. Never

use tools. If the lever will not turn by hand, do not try to

repair it, call a qualified service technician. Force or

attempted repair may result in a fire or an explosion.

D. Do not use this appliance if any part has been under

water. Immediately call a qualified service technician to

inspect the appliance and to replace any part of the

control system and any gas control which has been

under water.

LIGHTING INSTRUCTIONS — ELECTRONIC

1. For complete shut-down, turn remote wall switch to

“OFF.”

2. Open lower control compartment door.

3. Turn the ON/OFF switch to “OFF”. Do not force.

4. Close the main line shut-off valve.

5. Close lower control compartment door.

TO TURN OFF GAS TO APPLIANCE

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above on this page.

2. Turn remote wall switch to “OFF.”

3. Open lower control compartment door.

4. Verify main line shut-off valve is open.

5. Turn the ON/OFF switch to “OFF”. Do not force.

6. Wait five (5) minutes to clear out any gas. If you then

smell gas, STOP! Follow “B” in the safety information

above on this page. If you do not smell gas, go to the

next step.

7. Turn the ON/OFF switch to “ON”. Do not force.

8. Turn “ON” all electrical power to appliance (remote wall

or appliance switch).

9. Close lower control compartment door.

TO SHUT OFF

1. Turn off all electrical power to the appliance (remote wall

switch).

ON/OFF Switch

OFF

PSI

CONTROL

IGNITER

Front View

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

INSTRUCTIONS D’ALLUMAGE — ELECTRONIC

INSTRUCTIONS D’ALLUMAGE

POUR VOTRE SÉCURITÉ, LISEZ CES INSTRUCTIONS AVANT L’ALLUMAGE

A. Lorsque vous allumez l’appareil, suivez exactement ces instruc-

tions.

B. AVANT L’ALLUMAGE: Assurez-vous que vous ne détectez

aucune odeur de gaz autour de l’apareil ainsi que près du sol;

certains gaz, étant plus lourds que l’air, descendent au niveau

du sol.

VOICI CE QUE VOUS DEVEZ FAIRE SI VOUS DÉCELEZ UNE

ODEUR DE GAZ

•Éteignez toute flamme visible.

•Ouvrez les fenêtres.

•N’allumez aucun appareil.

•Ne touchez à aucun commutateur électrique.

•Ne vous servez d’aucun téléphone dans votre édifice.

AVERTISSEMENT: SI VOUS NE SUIVEZ PAS CES INSTRUCTIONS À LA LETTRE, IL POURRAIT S’EN SUIVRE UN INCENDIE OU

UNE EXPLOSION CAUSANT DES DOMMAGES MATÉRIELS, DES BLESSURES CORPORELLES OU MÊME DES PERTES DE VIE.

•Appelez immédiatement votre compagnie de gaz en utilisant

le téléphone du voisin.

•S’il vous est impossible de contacter votre compagnie de

gaz, appelez le service des incendies.

C. N’utilisez que votre main pour manipuler l'interrupteur “ON/

OFF” de la valve à gaz. N’utilisez jamais d’outils. Si

l’interrupteur ne bouge pas manuellement, n’essayez pas de le

réparer. Communiquez immèdiatement avec un technicien de

service qualifié. Toute tentative pour forcer l’interrupteur ou le

réparer, risquerait de provoquer un incendie ou une explosion.

D. Ne vous servez pas de cet appareil si l’un de ses éléments a été

immergé dans l’eau. Appelez immédiatement un technicien

compétent pour faire inspecter l’appareil et remplacer toute

pièce du système de réglage ou commande du gaz qui a été sous

l’eau.

1. ARRÊTEZ ! Lisez les consignes de sécurité au verso de cette

plaque.

2. Tournez l’interrupteur mural à la position d’arrêt “OFF”.

3. Ouvrez la porte du compartiment de contrôle du bas.

4. Assurez-vous que la soupape d’arrêt de la canalisation principale

est ouverte.

5. Tournez la manette de réglage du gaz à la position d’arrêt “OFF”.

6. Attendez cinq (5) minutes pour l’evacuation du gaz. Si vous

décelez une odeur de gaz ARRÊTEZ ! Retournez au point “B” des

consignes de sécurité au verso de cette plaque. Si vous ne

remarquez aucune odeur de gaz, passez à l’étape suivante.

7. Tournez la manette de réglage du gaz jusqu’à la position de marche

“ON”. Ne la forcez pas.

8. Ouvrez le courant électrique (“ON”) qui alimente l’appareil

(interrupteur mural ou l'appareil).

9. Fermez la porte du compartiment de contrôle du bas.

10. Au besoin, rebrancher l’apareil au courant électrique et

remettre l’interrupteur principal du brûleur à la position “ON”

ou régler le thermostat à la température désirée.

11. Si l’appareil ne se met pas en marche, suivre les instructions

intitulées “Pour fermer le gaz qui alimente l’appareil” et appeler

un technicien ou le fournisseur de gaz.

POUR ÉTEINDRE L’APPAREIL

1. Coupez tout le courant électrique qui alimente l’appareil (interrupteur

mural).

POUR FERMER LE GAZ QUI ALIMENTE L’APPAREIL

3. Tournez la manette de réglage du gaz à la position d’arrêt “OFF”.

Ne la forcez pas.

4. Fermez la soupape d’arrêt de la canalisation principale.

5. Fermez la porte du compartiment de contrôle du bas.

1. Pour une fermeture complète, tournez l’interrupteur mural à la

position d’arrêt “OFF”.

2. Ouvrez la porte du compartiment de contrôle du bas.

Interrupteur

ON/OFF

OFF

PSI

CONTROL

IGNITER

Vue de face

18 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

TROUBLESHOOTING THE MILLIVOLT GAS CONTROL SYSTEM

1. Spark ignitor will not light

pilot after repeated

triggering of ignitor button.

2. Pilot will not stay lit after

carefully following the

lighting instructions.

3. Pilot burning, no gas to

burner, Valve knob “ON,”

Wall Switch “ON.”

4. Frequent pilot/burner outage

problem.

CORRECTIVE ACTIONSYMPTOM

A. Defective ignitor

(no spark at electrode).

B. Defective or misaligned electrode

at pilot (spark at electrode).

C. Gas supply pressure errant.

D. Pilot orifice plugged.

A. Defective pilot generator

(thermocouple).

A. Limit Switch defective.

B. Wall switch or wires defective.

C. Thermopile may not be generating

sufficient millivoltage.

D. Plugged burner orifice.

A. Pilot flame may be too low or

blowing (high) causing the pilot/

valve safety to drop out.

Check for spark at electrode and pilot; if no spark and

electrode wire is properly connected, replace ignitor.

POSSIBLE CAUSES

ote: Before troubleshooting, make sure that the appliance main line gas shut-off valve and the gas control valve are in the "OPEN"

position and the burner ON/OFF switch is in the “ON” position.

Important: Valve system troubleshooting should only be accomplished by a qualified service technician.

Clean and/or adjust pilot flame for maximum flame impinge-

ment on thermocouple

(Figure 11 on page 8)

Check burner orifice for stoppage and remove.

Check thermopile with millivolt meter. Take reading at thermo-

pile terminals of gas valve. Should read 325 millivolts mini-

mum with optional wall switch “OFF.” Replace faulty thermo-

pile if reading is below specified minimum.

Check wall switch and wires for proper connections. Jumper

wire across terminals at wall switch, if burner comes on,

replace defective wall switch. If okay, jumper wires across wall

switch wires at valve, if burner comes on, wires are faulty or

connections are bad.

Check pilot flame, it must impinge on thermocouple

(Figure

11 on page 8)

Clean and/or adjust pilot for maximum flame

impingement on thermocouple. Ensure that the connection

between the valve and thermocouple are tight and secure.

Clean or replace pilot orifice.

Check inlet gas pressure. It should be within the limits as

marked on the rating plate.

Using a match, light pilot. If pilot lights, turn off pilot and

trigger the ignitor button again. If pilot lights, an improper gas

mixture caused the bad lighting and a longer purge period is

recommended. If pilot will not light – check gap at electrode

and pilot – should be ¹⁄₈" to have a strong spark. If gap

measures ¹⁄₈", replace pilot

(Figure 11 on page 8)

Isolate the “limit” switch. Disconnect the wires from the “ON/

OFF” switch and the valve (label wires for reattachment). Test

for continuity with a multimeter. If continuity is not indicated,

switch is defective and must be replaced.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

TROUBLESHOOTING THE ELECTRONIC IGNITION SYSTEM

SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION

See Below.

Disconnect the two black wires from the wire nuts. Test switch(s) for

continuity with a multimeter. If continuity is not indicated, switch(s) is

defective and must be replaced.

Note: Before replacing “OFF/ON” switch, be sure to check wiring for loose

connections or broken wires and repair as needed.

Check main burner orifice(s) for stoppage. Clean or replace.

Check vent system for obstructions.

A. Faulty Valve System.

B. “OFF/ON” or wall switch

defective.

A. Burner orifice plugged.

B. Obstructed vent system.

1. Burner will not light.

2. Burners come “ON” but

go “OFF.”

ote: Before troubleshooting, make sure that the appliance main line gas shut-off valve and the gas control valve are in the "OPEN"

position and the burner ON/OFF switch is in the “ON” position.

Important: Valve system troubleshooting should only be accomplished by a qualified service technician.

• Turn Off Gas Supply

• Assure Valve Switch Is In ON Position

• Disconnect Control Harness

• Set Thermostat To Call For Heat

• Check For Proper Voltage At Control Harness

(See Insert A). Voltage Should Be 24V

Between Thermostat Or Pressure Switch

And 24V Common And 24V Hot.

• Line Voltage Power

• Low Voltage Transformer

• Limit Controller

• Thermostat

• Wiring

CHECK

START

• Plug Control Harness Into Valve. Wait For

Internal Check Delay.

YES

• Igniter Warms Up And Glows Red.

• With Pilot Burner Cable Connected, Measure

Voltage At Valve HSI Element Output. 24V

Nominal. (See Insert B)

• Replace Igniter/Flame Rod Assembly.

YES

• Replace Valve.

• Turn On Gas Supply. • Pilot Burner Lights. • Check That Pilot Gas Is Flowing. Wait To

Assure Plot Gas Tubing Is Purged. Recycle

Call For Heat If Necessary.

YES

• Measure Voltage Between 24V Hot And 24V Common

Leads To Valve Control. Must Measure At Least 19.5

VAC With Igniter Powered (See Insert A). To Identify

Proper Lead, This Check Must Be Done With The

Valve Control Connected And Igniter Powered.

• Check Transformer And

Line Volt Supply.

• Replace Pilot Assembly.

YES

• Check That Pilot Flame Makes Good Contact With

Pilot Burner Flame Rod.

• Check For Good Electrical Connection Through The

Pilot Tubing.

• If Both Of The Above Are Good, Replace Igniter/Flame

Rod Assembly.

• Cycle Thermostat Off And Back On.

YES

• Main Valve Opens And Main Burner Lights. NO

YES

• System Is Okay.

YES

• Main Burner Lights. NO

Igniter Will Cycle Off And Back On Once During

The 90 Second Ignition Trial. All Voltage

Measurements Must Be Taken While The Igniter

Is Powered.

When Measured Voltage At Connections, Use

Care To Assure Terminals Are Not Damaged.

• Replace Valve.

24 Volt Hot

End View Of

Control Harness

Connector

24 Volt

Common

24 Volt

Switched

Check For Damaged Or Missing Terminals

In Connector

Insert A

Igniter Terminals

Insert B

20 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

REPLACEMENT PARTS

GAS CONTROLS — HONEYWELL ELECTRONIC

GAS CONTROLS — SIT MILLIVOLT

GAS ORIFICES — SIT AND HONEYWELL SYSTEMS

.oNNOITPIRCSED larutaNenaporP

.oNtraP.ytQ.oNtraP.ytQ

.03TIS-evlaVsaG1070K3411035J881

.13retingIozeiP1068K0111068K011

.23ylbmessAtoliP1071L9611081L961

.33rotareneGtoliP1097J0611097J061

.43elpuocomrehT1075L4711075L471

.53ebuTtoliP1065L4711065L471

.63elbaCdnAedortcelE1085L4711085L471

.73)lenaPytsedoM(rekcitS1056M4211056M421

.oNNOITPIRCSED larutaNenaporP

.oNtraP.ytQ.oNtraP.ytQ

.04llewyenoH-evlaVsaG1081L2611091L261

.14ylbmessAtoliP1041L2611051L261

.24remrofsnarT1023J2411023J241

.34)tiK(ylbmessArotingI45L78145L781

.44)lenaPytsedoM(rekcitS1005L9611005L961

.54ebuTtoliPA78479-BL1A78479-BL1

.oNNOITPIRCSED larutaNenaporP

.oNtraP.ytQ.oNtraP.ytQ

.05YABBE/2-FPBE/2-TSBEniaM-ecifirOsaG1008J0621025L912

.152-LCBE/2-RCBEniaM-ecifirOsaG1047K9921085L762

La page charge ...

Lennox Hearth Products EBSTPE-2 Manuel utilisateur

Marque: Lennox Hearth Products

Modèle: EBSTPE-2

Catégorie: Cheminées

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Lennox Hearth Products EBSTPE-2 User manual

Lennox Hearth Products EBSTPE-2 Manuel utilisateur

Lennox Hearth Products EBSTPE-2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents