Gaggenau 400 Series Top Control Built In Dishwasher Manuel utilisateur
- Catégorie
- Lave-vaisselle
- Taper
- Manuel utilisateur
Installation Instructions
Notice d’installation
9001705947 (0306)
*9001705947*
To avoid possible injury or property damage, OB-
SERVE ALL WARNINGS AND CAUTIONS.
installers only. The dishwasher must be installed by
• In addition to these instructions, the dishwasher
shall be installed to meet all electrical and plumb-
ing codes and ordinances (both national and
local).
Read these installation instructions completely
and follow them carefully. They will save you time
dishwasher performance.
IMPORTANT
• The dishwasher drain hose must be installed with
a portion of it at least 20
properly.
• This dishwasher is intended for indoor residential
use only, and should not be used in commercial
food service establishments.
Important Safety Instructions
• NEW INSTALLATION - If the dishwasher is a new
installation, most of the work must be done before
the dishwasher is moved into place.
• REPLACEMENT - If the dishwasher is replacing
another dishwasher, check the existing dishwasher
connections for compatibility with the new
dishwasher, and replace parts as necessary.
• This appliance has been found to be in compliance
with CAN/CSA-C22.2 No. 167/UL 749. It is the
responsibility of the owner and the installer to
determine if additional requirements and standards
• Not for outdoor use.
3
4
WARNING
Avoiding General Hazards
Do not use the dishwasher until it is completely
installed. When opening the door on an uninstalled
dishwasher, carefully open the door while supporting
the rear of the unit. Failure to follow this warning can
cause the dishwasher to tip over and result in serious
injury.
Before installing the “L”-shaped supplied countertop
mounting brackets (select models), decide which
method will be used to secure the dishwasher into its
opening. Once these mounting brackets are installed
damage the mounting brackets and the dishwasher.
In some conditions, hydrogen gas can form in a hot
water system that has not been used for weeks.
Hydrogen gas is explosive.
in a well ventilated area until there is no sound or evi-
dence of gas.
Temperatures required for soldering and sweating will
damage the dishwasher’s base and water inlet valve.
If plumbing lines are to be soldered or sweated, keep
the heat source at least 6 (152.4 mm) away from the
dishwasher’s base and water inlet valve.
Removing any cover or pulling the dishwasher from the
cabinet can expose hot water connections, electrical
power and sharp edges or points. Handle with care.
Avoiding Electrical Shock/Fire Hazards
Do not allow the electrical and water supply lines to
touch. Separate channels are provided under the
dishwasher.
Do not work on an energized circuit. Doing so could
-
cians should perform electrical work. Do not attempt
any work on the dishwasher electric supply circuit
until you are certain the circuit is de-energized.
Make sure electrical work is properly installed. There
should be no loose electrical connections. Ensure all
electrical connections are properly made.
The customer has the responsibility of ensuring that
the dishwasher electrical installation is in compliance
with all national and local electrical codes and
ordinances. The dishwasher is designed for an
electrical supply of 120V, 60 Hz, AC, connected to a
dishwasher-dedicated, properly grounded electrical
circuit with a fuse or breaker rated for 15 or 20 amps.
Electrical supply conductors shall be a minimum #14
AWG copper only wire rated at 75°C (167°F) or higher.
This appliance must be connected to a grounded metal,
permanent wiring system, or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or
lead on the appliance. Do not use extension cords.
Avoiding Plumbing/Scalding Hazards
Do not perform any work on a charged hot water
plumbershould perform plumbing work. Do not attempt
any work on the dishwasher hot water supply plumbing
Do not over tighten the 90° elbow. Doing so may
damage the water inlet valve and cause a water leak.
Temperatures required for soldering and sweating
will damage the dishwasher’s water inlet valve. If
plumbing lines are to be soldered or sweated, keep
the heat source at least 6 (152.4 mm) away from the
dishwasher’s water inlet valve.
Check local plumbing codes for approved plumbing
procedures and accessories. All plumbing should be
done in accordance with national and local codes.
These instructions depict an installation method for
stainless steel braided hose or PEX hot water supply
lines. If using copper tubing or other material for
water supply, defer to a licensed plumber for proper
installation.
Proposition 65 Warning:
This product may contain a chemical known to
the State of California, which can cause cancer or
reproductive harm. Therefore, the packaging of your
product may bear the following label as required by
California:
STATE OF CALIFORNIA PROPOSITION 65 WARNING:
WARNING
Cancer and Reprodutive Harm - www.P65Warnings.ca.gov
5
Hot Water Supply Line - Minimum 3/8 O.D. copper tubing or metal
braided dishwasher supply line
Hammer Hole Saw Pipe Wrench
Tape Measure Slot Screwdriver Phillips Screwdriver Torx T-20 Screwdriver
Ø 2 mm (1/16 in) Drill Level
Adjustable Wrench
Tools and Materials Needed
Inspect the Dishwasher
After unpacking the dishwasher and prior to installation,
thoroughly inspect the dishwasher for possible freight
or cosmetic damage. Report any damage immediately.
Cosmetic defects must be reported within 30 days of
installation.
NOTE: Do not discard any bags or items that come with the
original package until after the entire installation has been
completed.
5
Torx T-15 Screwdriver Pencil Center Punch Square
6
A
B
F
G
I
H
K
L
C
E
D
AExtra Tall Item Sprinkler (See Use and Care Manual)
BToe Panel Screws
CMounting Brackets
DMounting Bracket Screws
EToe Panel (2 pieces)
FToe Panel caps and screws (select models only)
GScrew Clamp (for hose)
HWater Supply Adaptor Fitting
IFlexible Edge Protector Grommet for electrical wire
JRubber Drain Hose Adaptor
KToe Panel Mounting Brackets (select models only)
LOuter toe panel (3rd piece) (select models only)
MSide Mount Force Distributor (Alternate Side Mount only)
NMounting Bracket Screws (Alternate Side Mount only)
OMeasuring Template for Vario-Hinge Fully Integrated
Door Panel
PPower Cord
QWrench (wrench size 13)
REmergency Release
SScrews for heavy wooden front door panel
TMetal Mounting Brackets
UHook and Loop Fastener Strips
Materials Supplied
J
M
S
Ø 4x15 mm
Ø 4x13 mm
Ø 4x17 mm
Q
R
ø 4x30
T
P
Ø 4x36 mm
N
O
U
7
After locating the proper place for your new dishwasher,
you will need to create any required openings to allow for
passage of the water, drain and electrical line. In order to
avoid interference with the dishwasher when sliding it into the
cabinet, place your openings within the dimensions shown
in Figure 3 below.
Required Openings:
43/43/8(120 x 60 mm) - To pass the included electrical supply
power cord through to adjacent cabinet.
Note: If the incoming electric supply, water supply and drain
connections are all in the same cabinet, the one 43/4″ x 23/8″
(120 x 60 mm) hole will be large enough for all three to pass
through.
(100 x 50 mm) - To pass the included water supply line
toward the water supply
11/4(32 mm) diameter - To pass the dishwasher drain hose
toward the drain connection
Check clearance
between
dishwasher door
and wall
Countertop
23
- 241/
4
(600 - 616 mm)
Figure 2
Enclosure Requirements
WARNING
Avoid Scalding or Electrical Shock Hazard!
Make sure the water supply and electrical supply
are shut o before installation or service.
Avoid Electrical Shock/Fire Hazard
Do not allow the electrical and water supply lines
to touch.
WARNING
90°
22
5
/
8
(575 mm)
Figure 3
4
1
/
2
"
(114mm)
2
1
/
2
"
(64mm)
If the dishwasher is to be installed in a corner, make sure
that there is adequate clearance to open the door. See
Figure 2 below.
Note: This dishwasher is designed to be enclosed on the
top and both sides by standard residential kitchen cabinetry.
Select a location as close to the sink as possible for easy
access to water supply and drain lines.
For proper dishwasher operation and appearance, ensure
that the enclosure is square and has the dimenions shown
in Figure 1 below.
NOTE: If your dishwasher opening width measures
>23 5/8″ (600 mm), use the TOP or SIDE MOUNT mount-
ing methods.
If your dishwahser opening width measures 23 5/8″ (600
mm), use the ALTERNATIVE SIDE MOUNT mounting
method.
Figure 1
34-36¼(867-927mm)
8
Figure 5
Before sliding the dishwasher into the cabinet, remove the
hose clip at the back of the dishwasher as shown in Figure
4. The hose clip may be used later to hold the drain hose as
shown in Figure 12.
Figure 4
In select models, remove the rubber apron on top of the
dishwasher and set aside for later use. See Figure 5.
Dishwasher Preparation
Add the 9 pieces of hook and loop fasteners to the outer
door. Remove the side deco strips and reserve the strips
and the screws for later.See Figures 6 & 7.
Figure 6
Figure 7
Pinch Point Hazard!
Sliding parts. Keep ngers out of openings on
inner door!
WARNING
Sliding parts
9
Electrical Preparation
WARNING
Dishwasher Electrical Rating
Volts Hertz Amperes Watts
120 60 12 1,440
(max)
Electrical Supply
The customer has the responsibility of ensuring that the dish-
washer electrical installation is in compliance with all national
and local electrical codes and ordinances. The dishwasher is
designed for an electrical supply of 120V, 60 Hz, AC, connect-
ed to a dishwasher-dedicated, properly grounded electrical cir-
cuit with a fuse or breaker rated for 15 or 20 amps.
Grounding Instructions
This appliance must be grounded. In the event of a malfunc-
tion or breakdown, grounding will reduce the risk of electric
shock by providing a path of least resistance for electric
current. This appliance is equipped with a cord having an
equipment-grounding conductor and a grounding plug. The
plug must be plugged into an appropriate outlet that is in-
stalled and grounded in accordance with all local codes and
ordinances.
Make sure that the dishwasher is connected to a suitable
ground in compliance with all local codes or, in the absence of
a local code, with the NATIONAL ELECTRICAL CODE in the
United States or the CANADIAN ELECTRIC CODE C22.1-
latest edition in Canada as well as any provincial/state or
municipal or local codes that apply.
Note: Installations requiring hard wiring and terminal
block - The accessory terminal block/junction box model,
SMZPCJB1UC, designed for permanent wire connection, is
not included but can be ordered through Customer Service by
calling 1-800-944-2904. Follow the instructions included with
the kit.
• Plug the end of the supply cord into the back of the
dishwasher.
• The outlet for the power supply cord should be located in
a cabinet or wall adjacent to the dishwasher cabinet.
• Do not plug dishwasher in until all the steps of installation
are complete.
Note: Only use the included power cord. If cord is missing
order kit SMZPC002UC through Customer Service.
Figure 8
Avoid Electrical Shock Hazard!
Do not work on an energized circuit. Doing so could
should perform electrical work. Do not attempt any work
on the dishwasher electric supply circuit until you are
certain the circuit is de-energized.
Improper connection of the equipment-grounding conduc-
tor can result in a risk of electric shock. Check with a
whether the appliance is properly grounded.
To avoid possible injury or property damage, care should
be exercised when the dishwasher is installed or removed
to reduce the likelihood of damage to the power cord.
Avoid Fire Hazard!
Make sure electrical work is properly installed and
Make sure there are no loose electrical connections. Make
sure all electrical connections are properly made.
Loose and improperly installed electrical connections
can result in overheating!
Wall Socket Connections:
Only use the provided power cord for wall socket
connections.
DO NOT
cord or adapter with this appliance.
DO NOT cut or splice the power cord.
DO NOT alter the power cord in any way.
Permanent Wire Connections (in addition to the
warnings above):
Only use the junction box power cord, sold as Accessory
kit #SMZPCJB1UC.
Carefully review the terminal block installation instructions.
DO NOT remove, alter or bypass the terminal block.
Al
te
rn
at
e
c
a
b
l
e rout
i
ng
10
Hot Water Supply
The hot water heater should be set to deliver approximately
120° F (49° C) water to the dishwasher. Water that is too
water temperatures will increase run times. The hot water
supply pressure must be between 15 - 145 psi (1 - 10 bar).
IMPORTANT NOTES:
sure to make all solder connections before connecting the
water supply line to the dishwasher.
· Make sure there are no sharp bends or kinks in the water
· Always use the appropriate seal when making plumbing
connections.
· Before connecting the water supply line to the dishwasher,
to clear any foreign material.
· Turn on the water supply and check for leaks after
connections are made.
Water Supply Shut O Valve
the hot water supply line, as shown in Figure 9. All solder
connections must be made before the water line is connected
to the dishwasher.
Temperatures required for soldering and sweating
will damage the dishwasher. If plumbing lines
are to be soldered or sweated, keep the heat
source at least 6 inches (152.4 mm) away from
the dishwasher.
Avoid Scald Hazard!
Do not perform any work on a charged hot water
line. Serious injury could result. Only qualied
plumbers should perform plumbing work. Do not
attempt any work on the dishwasher hot water
supply plumbing until you are certain the hot water
supply is shut o.
WARNING
Inlet Water Connections Connecting the Hot Water Supply
There are two plastic corrugated hoses that exit the back of
end, is the water supply hose to the dishwasher (the other
3/4
(76 x 45 mm) opening through the cabinet to pass the dish-
To connect the hot water supply:
parts bag onto the dishwasher water supply hose. This
2. Pass the dishwasher water supply line with attached
valve. Take care not to allow the hose to kink or twist
behind the dishwasher.
3. Connect the dishwasher water supply line with adaptor to
this connection. Always use the appropriate seal when
making plumbing connections.
NOTE: The end of the dishwasher water inlet hose is
heavy and will need to be supported. It is best to lay the
end on the cabinet oor as shown in Figure 9.
4. After all connections are made, turn on the hot water and
check for leaks.
The dishwasher drain hose may be connected to the house-
a 1¼" diameter hole in order to pass the drain hose through
the cabinet.
1 Directly under the sink dishwasher drain connection, as
shown in Figure 11.
2 Directly to a disposer dishwasher drain connection, as
shown in Figure 12.
3 To the under sink dishwasher drain connection through
an air gap, as shown in Figure 13.
4 To a disposer dishwasher drain connection through an air
gap, as shown on Figure 14.
Figure 9
Drain Connections
11
IMPORTANT NOTES:
· If local ordinance require an air gap, install it according
to the manufacturer’s instructions.
· If the dishwasher drain hose is to be connected to a
disposer dishwasher drain connection, remove the plug
from the disposer’s dishwasher drain connection.
· The dishwasher drain hose must have one place along
· The drain hose length can be extended if necessary. The
maximum length of the drain hose, including the hose
Figure 13 Figure 14
Figure 11
Figure 10
Non-Metallic Tie
MIN.
20"
MIN.
20"
Non-Metallic Tie
Figure 12
Remove
plug
max 43” (1100mm)
G
G
G
G
min 20 (508mm)
max 33 (838mm)
min 20 (508mm)
max 33 (838mm)
12
For a large port, use the drain hose as it is.
1. For a small port, insert the rubber drain hose adaptor
into the drain hose end.
2. Obtain the Rubber Drain Hose Adaptor (J) spring clamp
from the Dishwasher Installation Kit (do not substitute).
3. Insert the dishwasher drain hose into the end of the
drain hose (see Figure 15). Be sure to fully insert the
drain hose.
4. Use the clamp provided to attach the Rubber Drain Hose
Adaptor to the house plumbing as shown in Figure 16.
The dishwasher can be secured into its enclosure in 3 ways:
NOTE: If your dishwasher opening width measures >235/8″
(600 mm) use the TOP or SIDE MOUNT mounting methods.
If your dishwasher opening width measures 235/8″ (600 mm)
use the ALTERNATE SIDE MOUNT mounting method.
Figure 16
Before installing the supplied countertop mounting
brackets, decide which method of securing the
dishwasher into its enclosure will be used. Once the
mounting brackets are installed on the dishwasher,
removing them is difficult and will damage the
mounting brackets and the dishwasher.
Installation of Mounting Brackets
Installation of Rubber Drain Hose Adaptor
Figure 17
Alternate Side Mount for opening 235/8). Insert
a side mount force distributor (M) in each side as shown in
Figure 18.
Alternate Side Mount
Figure 18
M
M
M
J
G
C
Side Mount is used for countertops made of marble,
granite, or other very hard materials that cannot be easily
drilled. Bend the mounting brackets along the small holes
and in the same direction as the two small tabs. Orient the
mounting brackets as shown in Figure 17 and position
the two small tabs on the mounting brackets over the two
slots on the dishwasher’s front corners. Push the mounting
perforated edge down as shown.
Top Mount is used for countertops made of wood or other
materials that can be easily drilled. Orient the mounting
brackets as shown in Figure 17 and position the two small
tabs on the mounting brackets over the two slots on the
dishwasher’s front corners. Push the mounting brackets
in Top Mount and Side Mount is the screw will be placed
to “Securing the Dishwasher” section on the next page).
Top and Side Mount
Figure 15
13
Levelling the Dishwasher
The unit should now be ready to slide into the cabinet
and caution when sliding the dishwasher into the cabinet.
1. Make sure that the hoses and cords do not bunch up
behind the unit or kink as you slide the unit back. Make
certain to slide the unit into place before raising the leg
levelers.
2. Level the dishwasher horizontally by turning feet
clockwise to raise or counter-clockwise to lower front
of the unit. See Figure 19.
3. Level the dishwasher vertically by turning center screw
to raise or lower the back.See Figure 19.
4. Be sure there is no space between the top of the
dishwasher and the underside of the counter. Then use a
level to check that the counter is still level. See Figure 20.
Figure 19
Q
Avoid Tip Over Hazard
Do not use the dishwasher until it is completely
installed. When opening the door on an uninstalled
dishwasher, carefully open the door while
supporting the rear of the unit. Failure to follow
this warning can result in serious injury.
WARNING
Figure 20
Pinch Point Hazard!
Sliding parts. Keep ngers out of openings on
inner door!
WARNING
Sliding parts
14
10 - 24 lbs.
Measure that same distance (A) on the door panel starting
at the top of the panel.
Use the template to mark the center of the panel and draw
a vertical line down the center of the panel.
Use the template to draw a horizontal line across at A.
Figure 23
Figure 24
Figure 25
10 - 24 lbs.
max. 31 7/ in.
Using the template, mark the dots for I. See Figure 24.
Measure from the top of the dishwasher to the base of
the bracket insertion, as shown in Figure 22. Record that
distance (A).
Preparing the Panel
Remove plastic inserts from the slots on outer door as
indicated in Figure 21.
Figure 21
O
Figure 22
Pinch Point Hazard!
Sliding parts. Keep ngers out of openings on
inner door!
WARNING
IMPORTANT NOTE:
• The door panel should weigh between 10 and 24
pounds. If it is heavier, call Customer Service.
15
⁄in
(2 mm)
⁄in
(2 mm)
Attaching the Mounting Brackets
Move the template 11.4 (290 mm) from the line A. Draw
another line and mark the dots at II.
Figure 26
Figure 27
Figure 28
Attach the mounting brackets to the panel with screws
power drill.
Make pilot holes with a hammer and a center punch. Use a
drill to drill 2/3 way through the panel.
DT
Figure 29
in
1
1
.
4
i
n
1
1
.
4
i
n
16
Attaching the Apron Attaching the Panel
Figure 30
Remove tape covering adhesive strip on the rubber apron.
Adhere the apron to the front of dishwasher.
Figure 31
Figure 32
Attach panel to dishwasher by lining up brackets on the
panel with slots and allow the panel to slide down into
place.
Pinch Point Hazard!
Sliding parts. Keep ngers out of openings on
inner door!
WARNING
Sliding parts
17
Reattach Deco Strips
Figure 33
Figure 34
Make sure dishwasher is square to the counter and then
reattach the deco strips on the sides. Use a Torx 15
screwdriver only, not a power drill.
Level the Dishwasher
Level the dishwasher again,using the same method as
described on page 13. Figure 35
18
Center the dishwasher in the opening before securing it to
your cabinet or countertop as shown in Figure 37. Use the
supplied emergency release tools (R) to open the appliance
as shown in Figure 38
For Side Mount - Stone Countertop
Figure 36
Figure 37
Figure 39
For Alternate Side Mount
Figure 40
Figure 42
1/16
D~1/2
For Top Mount - Wooden Countertop
Figure 38
Drive the mounting screws through the holes in the mounting
brackets as shown for Top Mount (Figure 40), Side Mount
(Figure 41), and Alternative Side Mount (Figure 43).
Securing the Dishwasher If using alternative side mount, remove the top cutlery rack
as shown in Figure 40.
1/16
D
~½" (13 mm)
(2 mm)
Figure 41
Replace the top cutlery rack as shown in Figure 42.
R
19
>4
¾
“/ 120mm
adjust
ajustar
régler
min. 2 ¾“/ 70 mm
max. 4 ¾“/ 120 mm
When installing a heavy wooden door panel, adjust as
shown in Figure 43.
Your dishwasher comes with either a two-piece or three-
piece toe panel (model dependent) to allow height adjust-
ment.
1. Ensure the time projector is visible (depending on the
model). Also when attaching the toe panel, ensure the
distances are in the correct ranges. See Figure 44.
2. Position the slotted rear toe panel (part of E) on the
3. Position the mating front toe panel (part of E) on top of
the rear toe panel allowing the angled edge to rest on
the mating edge of the dishwasher.
4. Drive the two black screws (B) through the holes in the
toe panel to secure. Use the supplied screws to avoid
damaging the dishwasher. See Figure 45.
5. For models with a three-piece toe panel, the rubber apron
removed earlier may now be attached and should remain
behind the outermost toe panel.
6. For models with outer toe panel (3rd piece - L) slide the
brackets (K) provided, into the slots of the toe panel you
just attached.
7. Once you determine the correct position for the brackets,
remove the bracket and bend the metal tab. See Figure
45. This ensures that the toe panel will not slide in further
than you need.
8. Re-insert the brackets.
9. Attach the outer toe panel (L) onto the brackets and drive
the screws provided (F) in place to secure the toe panel
ensuring that the rubber apron is completely hidden
behind the outer toe panel.
Figure 44
Figure 45
Attaching the Toe Panel
B
B
E
K
F
L
Figure 43
S
20
Your dishwasher requires no special care other than
that described in the Care and Maintenance section of
the Use and Care Manual. If you are having a problem
with your dishwasher, before calling for service please
refer to the Self Help section in the Use and Care
Manual. If service is necessary, contact your dealer or
installer or an authorized service center.
Do not attempt to repair the appliance yourself. Any
work performed by unauthorized personnel may void
the warranty. If you are having a problem with your
dishwasher and are not pleased with the service you
have received, please take the following steps (in the
order listed below) until the problem is corrected to
your satisfaction:
1. Contact your installer or the Authorized Service
Contractor in your area.
2. E-mail us. See your Use and Care Manual for
instructions.
3. Write us at the address below:
BSH Home Appliances, Corp.
1901 Main Street, Suite 600
Irvine, CA 92614
4. Call us at the Customer Service phone number :
1-800-944-2904
Please be sure to include (if you are writing), or have
available (if you are calling), the following information:
• Model number
• Serial number
• Date of original purchase
• Date the problem originated
• Explanation of the problem
• Daytime phone number where you can be reached.
Please make a copy of your invoice and keep it with this
manual. The customer must show proof of purchase to
obtain warranty service.
Customer Service
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
Gaggenau 400 Series Top Control Built In Dishwasher Manuel utilisateur
- Catégorie
- Lave-vaisselle
- Taper
- Manuel utilisateur