VTech VG208 Guide de démarrage rapide
- Catégorie
- Téléphones
- Taper
- Guide de démarrage rapide
What’s in the box
Specifications are subject to change without notice.
© 2021 VTech Communications, Inc.|
© 2021 VTech Technologies Canada Ltd.
All rights reserved. 11/21. VG208-X_QSG_V1.2
Technical specifications
Frequency control Crystal controlled PLL synthesizer
Transmit frequency Handset: 1921.536-1928.448 MHz
Telephone base: 1921.536-1928.448 MHz
Channels DECT channel: 5
Nominal effective range Maximum power allowed by FCC and IC.
Actual operating range may vary according to
environmental conditions at the time of use.
Power requirement
Handset: 2.4V Ni-MH battery
Telephone base: 6V DC @ 0.4A
Charger: 6V DC @ 0.4A
Memory Phonebook: 50 memory locations;
up to 30 digits and 15 characters
Caller ID log: 30 memory locations;
up to 24 digits and 15 characters
Call block: 150 entries
Connect and activate
1
Basic operation
Quick start guide
VG208
VG208-2
After you install your telephone or power returns following a power outage and battery depletion, the handset and
telephone base will prompt you to set the date and time, and to configure the answering system through voice guide.
Date and time
Follow the steps below to set the date and time. For example, if the date is 25 August 2021, and the time is 10:59 AM:
Voice guide for answering system
After setting the date and time, the handset and telephone base will display Voice guide to... and set up Ans sys?
alternatively.
This feature assists you to do the basic setup of the answering system. You can follow the voice guide to record your own
announcement, set the number of rings and the message alert tone.
Setup your answering system by inputting
the designated numbers as instructed in the
voice guide.
Date: 08/25/21
ECO
Voice guide to... “Hello! This voice guide
will assist you with the
basic setup of your
answering system“
When the handset
and telephone base
prompt you to set
the date and time
When the handset
prompts you to set up
the answering system
via voice guide
Setup
2
Caller ID
If you subscribe to caller ID service, information about
each caller appears after the first or second ring.
The caller ID log stores up to 30 entries. Each entry
has up to 24 digits for the phone number and 15
characters for the name.
Review caller ID log entries
Mike Smith
595-9511
ECO
NEW
ANS ON
09:05pm 08/25
Caller ID
Enter number
595-9511_
ECO
Enter number
800-595-9511_
ECO
To Phonebook
ECO
Mike Smiths_
ECO
Save a caller ID log entry to the phonebook
Delete a caller ID log entry
Mike Smith
595-9511
ECO
NEW
ANS ON
09:05pm 08/25
When your
desired caller ID
entry displays on
the handset or
telephone base
screen
When your desired caller ID entry displays on the handset or
telephone base screen
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT162342/BT262342 (2.4V 300mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR1939
Quick
start
guide
Make a call
Handset: Telephone base:
Volume
Answer a call
End a call
Handset:
Dial a caller ID log entry
Mike Smith
595-9511
ECO
NEW
ANS ON
09:05pm 08/25
When your desired caller ID entry displays on the handset or
telephone base screen
- OR -
Telephones identified with this logo have reduced noise and
interference when used with most T-coil equipped hearing aids and
cochlear implants. The TIA-1083 Compliant Logo is a trademark of
the Telecommunications Industry Association. Used under license.
T
Compatible with
Hearing Ai
d T-Coil
TIA-1083
The ENERGY STAR® program (www.energystar.gov) recognizes and
encourages the use of products that save energy and help protect our
environment. We are proud to mark this product with the ENERGY
STAR® label indicating it meets the latest energy efficiency guidelines.
Disclaimer and Limitation of Liability
VTech Communications, Inc. and its suppliers assume no responsibility for any damage
or loss resulting from the use of this user’s manual. VTech Communications, Inc. and its
suppliers assume no responsibility for any loss or claims by third parties that may arise
through the use of this product.
Company: VTech Communications, Inc.
Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States
Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada
Handset:
Telephone base:
- OR - Lift the corded
handset
Handset: Telephone base:
Date: MM/DD/YY
ECO
Date: 08/2?/YY
ECO
Time: 1?:MM --
ECO
Time: 10:59 AM
ECO
Telephone base:
Mike Smith
595-9511
ECO
NEW
ANS ON
09:05pm 08/25
Press
Handset:
Telephone base:
Place the handset on
the telephone base
- OR -
DECT 6.0 corded/cordless telephone
1
Enter the date.
2
Press SELECT.
3
Enter the time.
4
Press SELECT.
1
Press MENU.
2
Press SELECT
to select To
phonebook.
3
Edit the phone
number
if needed.
4
Press SELECT.
5
Edit the name
if needed, then
press SELECT.
Press SELECT.
- OR -
2
Enter the
phone number
1
Press
- OR -
- OR -
Handset:
Press any dialing
keys to answer
Press
Press Press
1
Press .
2
Press / to
browse the entries.
LCD language setting
If you accidentally set the LCD language
to Spanish or French, press MENU and
then enter 364# to change the handset
LCD language back to English while the
handset is not in use.
Press
Connect the telephone base
If you subscribe to digital subscriber line (DSL) high-
speed Internet service through your telephone line,
make sure you connect a DSL filter (not included) to
the telephone wall jack.
Install the battery
Connect the charger
Charge the battery
Display
Telephone base ringer is off.
New voicemail received
from your telephone service
provider.
NEW
New caller ID log entries.
MSG#
0Telephone base message
counter displays the total
number of messages.
The battery is low and needs
charging.
The battery is charging.
The battery is fully charged.
Handset ringer is off.
New voicemail received
from your telephone service
provider.
NEW
There are new caller ID log
entries.
ANS ON Answering system is on.
MSG#
5/10 Handset displays the current
message number being played
and the total number of new/
old messages recorded.
ECO The ECO mode activates
automatically to reduce
power consumption when the
handset is within range of the
telephone base.
See Mount the telephone base (optional) online for the
wall mounting instructions.
Tip
Important safety instructions
When using your telephone equipment, basic
safety precautions should always be followed
to reduce the risk of fire, electric shock and
injury, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions
marked on the product.
3. Unplug this product from the wall outlet
before cleaning. Do not use liquid or
aerosol cleaners. Use a damp cloth for
cleaning.
4. CAUTION: Do not install the telephone
base at a height above 2 meters.
5. Do not use this product near water such as
near a bath tub, wash bowl, kitchen sink,
laundry tub or a swimming pool, nor in a
wet basement or shower.
6. Do not place this product on an unstable
table, shelf, stand or other unstable
surfaces.
7. Avoid placing the telephone system in
places with extreme temperature, direct
sunlight, or other electrical devices. Protect
your phone from moisture, dust, corrosive
liquids and fumes.
8. Slots and openings in the back or bottom
of the telephone base and handset are
provided for ventilation. To protect them
from overheating, these openings must
not be blocked by placing the product on
a soft surface such as a bed, sofa or rug.
This product should never be placed near
or over a radiator or heat register. This
product should not be placed in any area
where proper ventilation is not provided.
9. This product should be operated only
from the type of power source indicated
on the marking label. If you are not sure of
the type of power supply in your home or
office, consult your dealer or local power
company.
10. Do not allow anything to rest on the power
cord. Do not install this product where the
cord may be walked on.
11. Never push objects of any kind into this
product through the slots in the telephone
base or handset because they may touch
dangerous voltage points or create a short
circuit. Never spill liquid of any kind on the
product.
12. To reduce the risk of electric shock, do not
disassemble this product, but take it to
an authorized service facility. Opening or
removing parts of the telephone base or
handset other than specified access doors
may expose you to dangerous voltages
or other risks. Incorrect reassembling can
cause electric shock when the product is
subsequently used.
13. Do not overload wall outlets and extension
cords.
14. Unplug this product from the wall outlet
and refer servicing to an authorized service
facility under the following conditions:
• When the power supply cord or plug is
damaged or frayed.
• If liquid has been spilled onto the
product.
• If the product has been exposed to rain
or water.
• If the product does not operate
normally by following the operating
instructions. Adjust only those controls
that are covered by the operation
instructions. Improper adjustment of
other controls may result in damage
and often requires extensive work by
an authorized technician to restore the
product to normal operation.
• If the product has been dropped and
the telephone base and/or handset has
been damaged.
• If the product exhibits a distinct change
in performance.
15. Avoid using a telephone (other than
cordless) during an electrical storm. There
is a remote risk of electric shock from
lightning.
16. Do not use the telephone to report a
gas leak in the vicinity of the leak. Under
certain circumstances, a spark may be
created when the adapter is plugged into
the power outlet, or when the handset is
replaced in its cradle. This is a common
event associated with the closing of any
electrical circuit. The user should not
plug the phone into a power outlet, and
should not put a charged handset into
the cradle, if the phone is located in an
environment containing concentrations
of flammable or flame-supporting gases,
unless there is adequate ventilation. A
spark in such an environment could create
a fire or explosion. Such environments
might include: medical use of oxygen
without adequate ventilation; industrial
gases (cleaning solvents; gasoline vapors;
etc.); a leak of natural gas; etc.
17. Only put the handset of your telephone
next to your ear when it is in normal talk
mode.
18. The power adapter is intended to be
correctly oriented in a vertical or floor
mount position. The prongs are not
designed to hold the plug in place if it is
plugged into a ceiling, under-the-table or
cabinet outlet.
19. For pluggable equipment, the socket-
outlet shall be installed near the equipment
and shall be easily accessible.
20. CAUTION: Use only the
batteries indicated in this manual. There
may be a risk of explosion if a wrong type
of battery is used for the handset. Use
only the supplied rechargeable batteries
or replacement batteries (BT162342/
BT262342) for the handset. Do not dispose
of batteries in a fire. They may explode.
• Do not use the battery in following
conditions:
» High or low extreme temperature
during use, storage or
transportation.
» Replacement of a battery with an
incorrect type that can defeat a
safeguard.
» Disposal of a battery into fire or a
hot oven, or mechanically crushing
or cutting of a battery, that can
result in an explosion.
» Leaving a batteryin an extremely
high temperature surrounding
environment that can result in
an explosion or the leakage of
flammable liquid or gas.
» A battery subjected to extremely
low air pressure that can result in
an explosion or the leakage of
flammable liquid or gas.
21. Use only the adapter included with this
product. Incorrect adapter polarity or
voltage can seriously damage the product.
SAVE THESE INSTRUCTIONS
Battery
• CAUTION: Use Only Supplied Battery.
• Do not dispose of the battery in a fire.
Check with local waste management
codes for special disposal instructions.
• Do not open or mutilate the battery.
Released electrolyte is corrosive and may
cause burns or injury to the eyes or skin.
The electrolyte may be toxic if swallowed.
• Exercise care in handling batteries in
order not to create a short circuit with
conductive materials.
• Charge the battery provided with this
product only in accordance with the
instructions and limitations specified in
this manual.
Precautions for users of implanted cardiac
pacemakers
Cardiac pacemakers (applies only to digital
cordless telephones):
Wireless Technology Research, LLC
(WTR), an independent research entity,
led a multidisciplinary evaluation of the
interference between portable wireless
telephones and implanted cardiac
pacemakers. Supported by the U.S. Food and
Drug Administration, WTR recommends to
physicians that:
Pacemaker patients
• Should keep wireless telephones at least
six inches from the pacemaker.
• Should NOT place wireless telephones
directly over the pacemaker, such as in a
breast pocket, when it is turned ON.
• Should use the wireless telephone at the
ear opposite the pacemaker.
WTR’s evaluation did not identify any risk
to bystanders with pacemakers from other
persons using wireless telephones.
About cordless telephone
• Privacy: The same features that make a
cordless telephone convenient create
some limitations. Telephone calls are
transmitted between the telephone
base and the cordless handset by radio
waves, so there is a possibility that
the cordless telephone conversations
could be intercepted by radio receiving
equipment within range of the cordless
handset. For this reason, you should not
think of cordless telephone conversations
as being as private as those on corded
telephones.
• Electrical power: The telephone base
of this cordless telephone must be
connected to a working electrical outlet.
The electrical outlet should not be
controlled by a wall switch. Calls cannot
be made from the cordless handset
if the telephone base is unplugged,
switched off or if the electrical power is
interrupted.
• Potential TV interference: Some cordless
telephones operate at frequencies that
may cause interference to televisions
and VCRs. To minimize or prevent such
interference, do not place the telephone
base of the cordless telephone near or
on top of a TV or VCR. If interference
is experienced, moving the cordless
telephone farther away from the TV or
VCR often reduces or eliminates the
interference.
• Rechargeable batteries: Exercise care in
handling batteries in order not to create
a short circuit with conducting material
such as rings, bracelets and keys. The
battery or conductor may overheat and
cause harm. Observe proper polarity
between the battery and the battery
charger.
• Nickel-metal hydride rechargeable
batteries: Dispose of these batteries in a
safe manner. Do not burn or puncture the
battery. Like other batteries of this type, if
burned or punctured, they could release
caustic material which could cause injury.
Follow the following steps to set the date
and time if you skipped the prompt.
Set date/time
ECO
Press / to
scroll to Set date/time,
then press SELECT.
2
Press MENU.
1
Date: 08/25/21
ECO
Enter the date, then
press SELECT.
3Enter the time, then
press SELECT.
4
Time: 10:59 AM
ECO
Go to www.vtechphones.com (US)
to register your product for enhanced
warranty support and latest VTech
product news.
Go to phones.vtechcanada.com (CA)
for latest VTech product news.
Scan the QR code for
support information
US CA
For operations and guides to help you using your telephone system,
and for latest information and supports, go and check the online help
topics and online FAQs.
Use your smartphone or mobile device to access our online help.
• Go to https://help.vtechphones.com/VG208; OR
• Scan the QR code on the right. Launch the camera app or QR
code scanner app on your smartphone or tablet. Hold the device’s
camera up to the QR code and frame it.
Tap the notification to trigger the redirection of the online help.
- If the QR code is not clearly displayed, adjust your camera’s
focus by moving your device closer or further away until it
is clear.
You can also call our Customer Support at
1 (800) 595-9511 [in US] or
1 (800) 267-7377 [in Canada] for help.
Need help?
S
m
US CA
RS LE HAUT
h Ni-MH)
BATTERIES.
ESPILES.
CR1535
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
Battery Pack / Bloc-piles :
BT183342/BT283342 (2.4V 400mAh Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine CR1535
THIS SIDE UP
16 hrs
Telephone base:
Lift the corded handset
- OR -
1 set for VG208
2 sets for VG208-2
2 sets for VG208-2
Lift the corded
handset
- OR -
1
Press 2
Enter the
phone number
Handset: Telephone base:
BASE
NEW
10:30
PM
AM
12/25
MSG #
0
HANDSET
ECO
10:30PM 10/16
MSG #
NEW
ANS ON
AM
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
Silkscreen Rear
Translucent
Vtech Silver 04
Silkscreen Rear
Pantone 433C
Silkscreen Rear
Vtech Silver 04
FrontCrystal KeysCrystal KeysCrystal Keys
Silkscreen Rear
Vtech Silver 04
Crystal Keys
Back
Engraved
0.3mm
Watermark
Front
Silkscreen Top
Pantone 347C
Silkscreen Top
Pantone 200C
Silkscreen Top
Vtech Silver 04
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
Silkscreen Rear
Translucent
Vtech Silver 04
Silkscreen Rear
Pantone 433C
Silkscreen Rear
Vtech Silver 04
FrontCrystal KeysCrystal KeysCrystal Keys
Silkscreen Rear
Vtech Silver 04
Crystal Keys
Back
Engraved
0.3mm
Watermark
Front
Silkscreen Top
Pantone 347C
Silkscreen Top
Pantone 200C
Silkscreen Top
Vtech Silver 04
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
Silkscreen Rear
Translucent
Vtech Silver 04
Silkscreen Rear
Pantone 433C
Silkscreen Rear
Vtech Silver 04
FrontCrystal KeysCrystal KeysCrystal Keys
Silkscreen Rear
Vtech Silver 04
Crystal Keys
Back
Engraved
0.3mm
Watermark
Front
Silkscreen Top
Pantone 347C
Silkscreen Top
Pantone 200C
Silkscreen Top
Vtech Silver 04
About the built-in answering system and voicemail service
For message recording, your telephone has a built-in answering system, and it also supports voicemail service offered by your
telephone service provider (subscription is required, and fee may apply).
Built-in answering system VS Voicemail service
Built-in answering system Voicemail service
Supported by Telephone system Telephone service provider
Subscription No Yes
Fees No May apply
Answer incoming calls
• After 3 rings by default.
• It can be changed via handset or the
telephone base menu.
• Usually after 2 rings.
• It can be changed by contacting your telephone service provider.
Storage Telephone base Server or System
Display new messages • Handset - XX new messages
• Telephone base - Message window flashes
• Handset - and New voicemail
• Telephone base -
Retrieve messages
• Press on the telephone base; OR
• Press MENU, and then select Play messages
on the handset; OR
• Access remotely with an access code.
• Press on the dialpad, and enter an access number and/or
passcode from your telephone service provider.
Answering system
Turn the built-in answering system on or off
On the telephone base
Press to turn on;
press again to turn off. For C-UL compliance only
Mesures de sécurité importantes
Afin de réduire les risques d’incendie, de
blessures corporelles ou d’électrocution, suivez
toujours ces mesures préventives de base
lorsque vous utilisez votre téléphone :
1. Lisez et comprenez bien toutes les
instructions.
2. Observez toutes les instructions et mises en
garde inscrites sur l’appareil.
3. Débranchez ce téléphone de la prise
murale avant de le nettoyer. N’utilisez pas de
nettoyeurs liquides ni en aérosol. N’utilisez
qu’un chiffon doux et légèrement humecté.
4. ATTENTION: Ne pas installer le socle
téléphonique à une hauteur supérieure à
2 mètres.
5. N’utilisez pas ce produit près de l’eau, tel
que près d’un bain, d’un lavabo, d’un évier
de cuisine, d’un bac de lavage ou d’une
piscine, ou dans un sous-sol humide ou sous
la douche.
6. Ne déposez pas ce téléphone sur un
chariot, support ou table chancelants.
L’appareil pourrait tomber et être
sérieusement endommagé.
7. Évitez d’installer le système téléphonique
dans les endroits soumis à une température
extrême, à la lumière directe du soleil ou
à proximité immédiate d’autres appareils
électriques ou électroniques. Protégez votre
téléphone contre les sources d’humidité,
la poussière, les vapeurs et les liquides
corrosifs.
8. Le boîtier de l’appareil est doté de fentes
et d’ouvertures d’aération situées à l’arrière
ou en dessous. Afin d’empêcher la
surchauffe, ces ouvertures ne doivent pas
être obstruées en plaçant l’appareil sur un
lit, divan, tapis ou autre surface similaires.
Ne placez pas cet appareil à proximité d’un
élément de chauffage ni d’une plinthe
électrique. De plus, ne l’installez pas dans
une unité murale ou un cabinet fermé qui
ne possède pas d’aération adéquate.
9. Ne faites fonctionner cet appareil qu’avec le
type d’alimentation indiqué sur les étiquettes
de l’appareil. Si vous ne connaissez pas le
voltage de votre maison, consultez votre
marchand ou votre fournisseur d’électricité.
10. Ne déposez rien sur le cordon
d’alimentation. Installez cet appareil dans un
endroit sécuritaire, là où personne ne pourra
trébucher sur la ligne d’alimentation ni le
cordon téléphonique modulaire.
11. N’insérez jamais d’objets à travers les
fentes et ouvertures de cet appareil, car ils
pourraient toucher à des points de tension
dangereux ou court-circuiter des pièces,
ce qui constituerait un risque d’incendie
ou d’électrocution. N’échappez pas de
liquides dans l’appareil.
12. Afin de réduire les risques d’électrocution,
ne démontez pas l’appareil, mais
apportez-le plutôt à un centre de service
qualifié s’il doit être réparé. En enlevant
le couvercle, vous vous exposez à des
tensions dangereuses ou autres dangers
similaires. Un remontage inadéquat peut
être à l’origine d’une électrocution lors
d’une utilisation ultérieure de l’appareil.
Débranchez l’appareil avant de procéder
au nettoyage. Utilisez un chiffon humide
et doux.
13. Ne surchargez pas les prises de courant et
les rallonges.
14. Débranchez cet appareil de la prise
de courant et communiquez avec le
département de service à la clientèle de
VTech dans les cas suivants :
• Lorsque le cordon d’alimentation est
endommagé ou écorché.
• Si du liquide a été échappé dans
l’appareil.
• Si l’appareil a été exposé à une source
d’humidité telle que la pluie ou l’eau.
• Si le produit ne fonctionne pas
normalement en respectant les
instructions de fonctionnement.
Réglez uniquement les commandes
indiquées dans le les instructions de
fonctionnement. Les réglages incorrects
des autres commandes pourraient
provoquer un dommage qui pourrait
exiger un travail exhaustif de la part d’un
technicien autorisé afin de rétablir le
fonctionnement normal de l’appareil.
• Si le produit a été échappé et que
le socle et/ou le combiné a été
endommagé.
• Si le produit affiche une nette diminution
de sa performance.
15. Évitez d’utiliser un téléphone (autre
qu’un sans fil) pendant un orage. Les
éclairs peuvent être à l’origine d’une
électrocution.
16. N’utilisez pas le téléphone pour rapporter
une fuite de gaz à proximité de la
fuite. En certaines circonstances, une
flammèche pourrait être provoquée
lorsque l’adaptateur est branché à une
prise de courant, ou lorsque le combiné
est déposé sur le socle. Ceci est un
événement commun associé à la fermeture
d’un circuit électrique. L’utilisateur ne
devrait pas brancher le téléphone à
une prise de courant, et ne devrait pas
déposer le combiné chargé sur le socle,
si le téléphone se trouve à proximité d’un
endroit comportant des concentrations
de gaz inflammables, à moins que la
ventilation soit adéquate. Une flammèche
dans un tel endroit pourrait provoquer
un incendie ou une explosion. De tels
environnements peuvent comprendre:
des endroits où l’on utilise de l’oxygène
médical sans ventilation adéquate; des gaz
industriels (dissolvants de nettoyage, des
vapeurs d’essence, etc.); une fuite de gaz
naturel, etc.
17. Ne placez que le combiné de votre
téléphone près de votre oreille lorsqu’en
mode de conversation.
18. Ces adaptateurs ont été conçus pour être
orientés en position verticale ou montés au
sol. Les broches ne sont pas conçues pour
maintenir l’adaptateur en place si celui-ci est
barnché dans une prise au plafond ou sous
une table/ armoire.
19. Pour le MATERIEL RACCORDE PAR PRISE DE
COURANT, le socle de prise de courant doit
etre installe a proximite du materiel et doit
etre aisement accessible.
20. MISE EN GARDE: Il peut y avoir
un risque d’explosion si vous utilisez le
mauvais type de piles pour le téléphone.
N’utilisez que les piles rechargeable inclus
ou les piles de rechange (BT162342/
BT262342). N’incinérez pas les piles. Celles-
ci risqueraient d’exploser.
• Évite d’utiliser la batterie dans les
conditions suivantes:
»des températures extrêmes
faibles ou élevées auxquelles
une batterie peut être soumise
pendant l’utilisation, le stockage ou
le transport;
»Remplacement d’une batterie
par un type incorrect pouvant
supprimer une protection;
»mise au rebut d’une batterie dans
un feu ou dans un four chaud, ou
écrasement mécanique ou coupure
d’une batterie, susceptible de
provoquer une explosion;
»maintien d’une batterie dans
un environnement à très haute
température pouvant provoquer
une explosion ou la fuite de liquide
ou de gaz inflammables;
»batterie soumise à une pression de
l’air extrêmement faible pouvant
provoquer une explosion ou la fuite
de liquide ou de gaz inflammables.
21. N’utilisez que les adaptateurs inclus avec ce
produit. L’utilisation d’un adaptateur dont
la polarité ou la tension serait inadéquate
risque d’endommager sérieusement le
produit et mettre votre sécurité en péril.
CONSERVEZ CES INSTRUCTIONS
Pile
• N’utilisez que la pile incluse ou l’équivalent.
• Ne jetez pas la pile au feu. Vérifiez les
instructions spécifiques de mise aux rebus
auprès des autorités locales.
• N’ouvrez pas et ne mutilez pas la pile.
L’électrolyte qui s’en échapperait est corrosif
et pourrait causer des brûlures ou des
blessures aux yeux ou à la peau. L’électrolyte
est toxique si avalé.
• Soyez prudents lorsque vous manipulez
les piles afin d’éviter les courts-circuits
provoqués par des matériaux conducteurs.
• Rechargez la pile incluse avec cet appareil,
selon les instructions et limites spécifiées
dans ce guide d’utilisation.
Stimulateurs cardiaques implantés dans
l’organisme
Les simulateurs cardiaques (s’applique
uniquement aux téléphones numériques sans
fil) :
L’organisme ‘Wireless Technology Research, LLC
(WTR)’, une firme de recherche indépendante,
a mené une évaluation pluridisciplinaire des
interférences entre les téléphones sans fil
portatifs et les stimulateurs cardiaques implantés
dans l’organisme. Appuyée par l’Administration
des aliments et drogues (FDA) des États-Unis, la
firme WTR recommande aux médecins :
Avis aux détenteurs de stimulateurs cardiaques
• Ils doivent tenir le téléphone sans fil à
une distance d’au moins six pouces du
stimulateur cardiaque.
• Ils ne doivent PAS placer le téléphone sans
fil directement sur le stimulateur cardiaque,
tel que dans une poche de chemise,
lorsque celui-ci est en marche.
• Ils doivent utiliser le téléphone sans fil en
l’appuyant sur l’oreille qui se trouve dans la
direction opposée au stimulateur cardiaque.
L’étude effectuée par l’organisme WRS n’a
pas identifié de risque pour les détenteurs de
simulateurs cardiaques causés par les gens qui
utilisent un téléphone sans fil à proximité de
ceux-ci.
À propos des téléphones sans fil
Confidentialité : Les mêmes caractéristiques qui
constituent des avantages pour les téléphones
sans fil affichent également des restrictions.
Les appels téléphoniques sont transmis entre
le combiné sans fil et le socle par le biais
d’ondes radio ; il y a donc la possibilité que
vos conversations téléphoniques sans fil soient
interceptées par des équipements de réception
radio se trouvant dans la portée du combiné
sans fil. Pour cette raison, vous ne devez pas
percevoir les communications téléphoniques
sans fil comme étant aussi confidentielles que
celles des téléphones à cordons.
Alimentation électrique : Le socle de ce
téléphone sans fil doit être branché à une prise
électrique fonctionnelle. La prise électrique
ne doit pas être contrôlée par un interrupteur
mural. Les appels ne pourront pas être effectués
du combiné sans fil si le socle est débranché ou
mis hors tension ou si le courant est coupé.
Possibilité d’interférences aux téléviseurs :
Certains téléphones sans fil fonctionnent sur des
fréquences pouvant causer des interférences
aux téléviseurs et aux magnétoscopes. Pour
réduire ou prévenir de telles interférences, ne
placez pas le socle du téléphone sans fil près
ou sur un téléviseur ou magnétoscope. S’il y a
présence de parasites, il est conseillé d’éloigner
le téléphone sans fil du téléviseur ou du
magnétoscope afin de réduire possiblement les
interférences.
Piles rechargeables : Manipulez les piles avec
soin afin de ne pas les court-circuiter avec
des bagues, bracelets ou clés. Les piles ou le
conducteur peut surchauffer et causer des
blessures. Respectez la polarité adéquate entre
la pile et le chargeur.
Les bloc-piles rechargeables à l’hydrure
métallique de nickel : Jetez ces blocs-piles
de manière écologique et sécuritaire. Ne les
incinérez pas et ne les percez pas. Tel que
les autres piles de ce type, elles pourraient
dégager une matière toxique qui peut causer
des blessures corporelles si elles sont brûlées
ou percées.
The RBRC seal
The RBRC seal on the nickel-metal hydride battery indicates that VTech
Communications, Inc. is voluntarily participating in an industry program to collect
and recycle these batteries at the end of their useful lives, when taken out of
service within the United States and Canada.
The program provides a convenient alternative to placing used nickel-metal
hydride batteries into the trash or municipal waste, which may be illegal in your
area.
VTech’s participation makes it easy for you to drop off the spent battery at local retailers
participating in the program or at authorized VTech product service centers. Please call
1 (800) 8 BATTERY® for information on Ni-MH battery recycling and disposal bans/restrictions
in your area. VTech’s involvement in this program is part of its commitment to protecting our
environment and conserving natural resources.
The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.
FCC, ACTA and IC regulations
FCC Part 15
NOTE: This equipment has been tested and found to comply with the requirements for
a Class B digital device under Part 15 of the Federal Communications Commission (FCC)
rules. These requirements are intended to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modifications to this equipment not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Privacy of communications may not be ensured when using this telephone.
To ensure safety of users, the FCC/ISEDC has established criteria for the amount of radio
frequency energy that can be safely absorbed by a user or bystander according to the
intended usage of the product. This product has been tested and found to comply with the
FCC/ISEDC criteria. The handset may be safely held against the ear of the user. The telephone
base shall be installed and used such that parts of the user’s body other than the hands are
maintained at a distance of approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B).
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements
adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the
back or bottom of this equipment contains, among other things, a product identifier in the
format US:AAAEQ##TXXXX. This identifier must be provided to your telephone service
provider upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone
network must comply with applicable Part 68 rules and technical requirements adopted
by ACTA. A compliant telephone cord and modular plug is provided with this product. It is
designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack
should normally be used for connecting to a single line and an RJ14 jack for two lines. See the
installation instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may
connect to your telephone line and still have them ring when you are called. The REN for this
product is encoded as the 6th and 7th characters following the US: in the product identifier
(e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be five
(5.0) or less. For more information, please contact your telephone service provider.
This equipment must not be used with Party Lines. If you have specially wired alarm dialing
equipment connected to your telephone line, ensure the connection of this equipment
does not disable your alarm equipment. If you have questions about what will disable alarm
equipment, consult your telephone service provider or a qualified installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack until the
problem has been corrected. Replacement to this telephone equipment can only be made
by the manufacturer or its authorized agents. For replacement procedures, follow the
instructions outlined under the Limited warranty.
If this equipment is causing harm to the telephone network, the telephone service provider
may temporarily discontinue your telephone service. The telephone service provider is
required to notify you before interrupting service. If advance notice is not practical, you will
be notified as soon as possible. You will be given the opportunity to correct the problem
and the telephone service provider is required to inform you of your right to file a complaint
with the FCC. Your telephone service provider may make changes in its facilities, equipment,
operation, or procedures that could affect the proper functioning of this product. The
telephone service provider is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone
numbers (e.g., police, fire, medical) in these locations. If you do store or test emergency
numbers, please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to
the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
Privacy of communications may not be ensured when using this telephone.
The term ‘’IC:‘’ before the certification/registration number only signifies that the Industry
Canada technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 1.0. The REN indicates
the maximum number of devices allowed to be connected to a telephone interface. The
termination of an interface may consist of any combination of devices subject only to the
requirement that the sum of the RENs of all the devices not exceed five.
This product meets the applicable Innovation, Science and Economic Development Canada
technical specifications.
California Energy Commission battery
charging testing instructions
This telephone is set up to comply with the energy-conserving standards right out of the box.
These instructions are intended for California Energy Commission (CEC) compliance testing only.
When the CEC battery charging testing mode is activated, all telephone functions, except battery
charging, will be disabled.
To activate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power outlet. Make sure all handsets
are plugged with charged batteries before proceeding.
2. While you press and hold /FIND HANDSET, plug the telephone base power adapter back
to the power outlet.
3. After about 10 seconds, when the IN USE light starts flashing and the telephone base shows
Registering... and then De-register?, release /FIND HANDSET and immediately press it
within two seconds.
When the phone successfully enters the CEC battery charging testing mode, all handsets
display To register HS... and ...see manual alternately.
When the phone fails to enter this mode, repeat steps 1 to 3 above.
To deactivate the CEC battery charging testing mode:
1. Unplug the telephone base power adapter from the power outlet, and then plug it back in.
Then the telephone base is powered up as normal.
2. Press and hold /FIND HANDSET on the telephone base for about four seconds until the
IN USE light turns on and the handset shows Registering....
3. Press QUIET# on the handset. The handset shows Registered, and you hear a beep when
the registration process completes. This process takes about 60 seconds.
Limited Warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase
(“Consumer” or “you”) that the Product and all accessories provided in the sales package
(“Product”) are free from defects in material and workmanship, pursuant to the following terms
and conditions, when installed and used normally and in accordance with the Product operating
instructions. This limited warranty extends only to the Consumer for Products purchased and
used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and workmanship
during the limited warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will replace
at VTech’s option, without charge, a Materially Defective Product. If we replace the Product,
we may use new or refurbished replacement parts. If we choose to replace the Product, we
may replace it with a new or refurbished Product of the same or similar design. We will retain
defective parts, modules, or equipment. Replacement of the Product, at VTech’s option,
is your exclusive remedy. VTech will return the replacement Products to you in working
condition. You should expect the replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of
purchase. If VTech replaces a Materially Defective Product under the terms of this limited
warranty, this limited warranty also applies to the replacement Product for a period of either (a)
90 days from the date the replacement Product is shipped to you or (b) the time remaining on
the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical damage,
improper installation, abnormal operation or handling, neglect, inundation, fire, water or
other liquid intrusion.
2. Product that has been subjected to contact with liquid, water, rain, extreme humidity
or heavy perspiration, sand, dirt or the like; but then only to the extent the damage was
not caused by incorrectly securing the waterproof handset’s protective elements, for
example, failing to properly close a seal), or such protective elements are damaged or
missing (e.g. a cracked battery door), or subjecting a Product to conditions beyond its
stated specifications or limits (e.g. 30 minutes in 1 meter of fresh water).
3. Product that has been damaged due to repair, alteration or modification by anyone
other than an authorized service representative of VTech;
4. Product to the extent that the problem experienced is caused by signal conditions,
network reliability, or cable or antenna systems;
5. Product to the extent that the problem is caused by use with non-VTech accessories;
6. Product whose warranty/quality stickers, product serial number plates or electronic serial
numbers have been removed, altered or rendered illegible;
7. Product purchased, used, serviced, or shipped for repair from outside the United States
of America or Canada, or used for commercial or institutional purposes (including but
not limited to Products used for rental purposes);
8. Product returned without a valid proof of purchase (see item 2 below); or
9. Charges for installation or set up, adjustment of customer controls, and installation or
repair of systems outside the unit.
How do you get warranty service?
To obtain warranty service in the United States of America, please visit our website at
www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to phones.vtechcanada.com or
dial 1 (800) 267-7377.
NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls
and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit
and transportation and are responsible for delivery or handling charges incurred in the
transport of the Product(s) to the service location. VTech will return replaced Product under
this limited warranty. Transportation, delivery or handling charges are prepaid.
VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not
covered by this limited warranty, or proof of purchase does not meet the terms of this limited
warranty, VTech will notify you and will request that you authorize the cost of replacement
prior to any further replacement activity. You must pay for the cost of replacement and return
shipping costs for the replacement of Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech
service location along with a description of the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt) identifying the Product purchased
(Product model) and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Other limitations
This warranty is the complete and exclusive agreement between you and VTech. It supersedes
all other written or oral communications related to this Product. VTech
provides no other warranties for this Product. The warranty exclusively describes all of VTech’s
responsibilities regarding the Product. There are no other express warranties. No one is
authorized to make modifications to this limited warranty and you should not rely on any such
modification.
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also
have other rights, which vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and
merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one
year from the date of purchase. Some states/provinces do not allow limitations on how long
an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech
be liable for any indirect, special, incidental, consequential, or similar damages (including,
but not limited to lost profits or revenue, inability to use the Product or other associated
equipment, the cost of substitute equipment, and claims by third parties) resulting from the
use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitation or exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase
Set number of rings
You can set your answering system to answer calls at least two rings
earlier than your voicemail service. For example, if your voicemail
service answers after six rings, set your answering system to answer
after four rings. Thus, if you are on a call, or if the answering system
is busy recording a message and you receive another call, the
second caller can leave a voicemail message.
Delete all messages
Using the telephone base
Play the previous message
1Press MENU. 2Press / to scroll
to Answering sys,
then press SELECT.
3
Press / to scroll
to Ans sys setup,
then press SELECT.
4Press / to scroll
to # of rings,
then press SELECT.
Press / to scroll to
the desired number of
rings, then press SELECT.
5
Answering sys
ECO
Ans sys setup
ECO
# of rings
ECO
4
ECO
Skip a message
Repeat the playing message
Press - OR -
Message playback
On the telephone base
On a handset
1
Press MENU.
2
Press SELECT
to select Play messages.
Play messages
ECO
- OR -
Press
1
2
-------------- OR --------------
1
2
Press
1
2
Press
Phonebook
The phonebook can store up to 50 entries, which are shared
by all handsets and the telephone base. Each entry may
consist of a telephone number up to 30 digits, and a name up
to 15 characters.
Add a phonebook entry
595-9511_
ECO
Enter name
_
ECO
Mike Smith
ECO
Enter number
595-9511
ECO
1
Enter the
phone
number.
2
Press MENU.
3
Press SELECT.
4
Enter the name.
5 Press SELECT.
Review phonebook entries
Delete a phonebook entry
Mike Smith
800-595-9511
ECO
Delete entry ?
ECO
Mike Smith
800-595-9511
ECO
When your desired phonebook entry displays on the
handset screen
1
Press .
2
Press / to
browse the entries.
1
Press DELETE.
2
Press SELECT.
You can set the answering system to answer an incoming call after 2, 3, 4, 5 or 6 rings; or Toll saver.
If you choose Toll saver, the answering system answers a call after two rings when you have new messages, or after four rings when you have
no new messages. This enables you to check for new messages and avoid paying unnecessary long distance charges if you are calling from
outside your local area.
NOTE
Press - OR -
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Silkscreen Rear
Translucent
Vtech Silver 04
Silkscreen Rear
Pantone 433C
Silkscreen Rear
Vtech Silver 04
Front Crystal Keys Crystal Keys Crystal Keys
Silkscreen Rear
Vtech Silver 04
Crystal Keys
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
Silkscreen Rear
Translucent
Vtech Silver 04
Silkscreen Rear
Pantone 433C
Silkscreen Rear
Vtech Silver 04
FrontCrystal KeysCrystal KeysCrystal Keys
Silkscreen Rear
Vtech Silver 04
Crystal Keys
Back
Engraved
0.3mm
Watermark
Front
Silkscreen Top
Pantone 347C
Silkscreen Top
Pantone 200C
Silkscreen Top
Vtech Silver 04
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
Silkscreen Rear
Translucent
Vtech Silver 04
Silkscreen Rear
Pantone 433C
Silkscreen Rear
Vtech Silver 04
FrontCrystal KeysCrystal KeysCrystal Keys
Silkscreen Rear
Vtech Silver 04
Crystal Keys
Back
Engraved
0.3mm
Watermark
Front
Silkscreen Top
Pantone 347C
Silkscreen Top
Pantone 200C
Silkscreen Top
Vtech Silver 04
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
Silkscreen Rear
Translucent
Vtech Silver 04
Silkscreen Rear
Pantone 433C
Silkscreen Rear
Vtech Silver 04
FrontCrystal KeysCrystal KeysCrystal Keys
Silkscreen Rear
Vtech Silver 04
Crystal Keys
Back
Engraved
0.3mm
Watermark
Front
Silkscreen Top
Pantone 347C
Silkscreen Top
Pantone 200C
Silkscreen Top
Vtech Silver 04
Phonebook Call Block
Call Block
If you subscribe to caller ID service, you can set the telephone
to block unknown calls and certain undesired calls. The call
block list can store up to 150 entries.
Add a call block entry
Call block
ECO
Block list
ECO
Add new entry
ECO
Enter number
800-595-9511_
ECO
Mike Smiths_
ECO
Delete a call block list entry
When the desired call
block list entry displays
on the handset screen
Mike Smith
595-9511
ECO
09:05pm 08/25
2
Press / to scroll
to Call block, then
press SELECT.
3
Press SELECT
to select Block list.
4
Press / to scroll
to Add new entry,
then press SELECT.
1
Press MENU.
5
Enter number
then press SELECT.
6
Enter name
then press SELECT.
Press DELETE.
Block unknown calls
Call block
ECO
Calls w/o num
ECO
Block
ECO
Review a call block list entry
Call block
ECO
Block list
ECO
Review
ECO
1Press MENU.2Press / to scroll
to Call block,
then press SELECT.
3Press / to scroll
to Call w/o num,
then press SELECT.
Press MENU.
12Press / to scroll
to Call block,
then press SELECT.
3
Press SELECT
to select Block list.
4
Press SELECT
to select Review.
4
Press / to scroll
to Block, then
press SELECT..
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
Silkscreen Rear
Translucent
Vtech Silver 04
Silkscreen Rear
Pantone 433C
Silkscreen Rear
Vtech Silver 04
FrontCrystal KeysCrystal KeysCrystal Keys
Silkscreen Rear
Vtech Silver 04
Crystal Keys
Back
Engraved
0.3mm
Watermark
Front
Silkscreen Top
Pantone 347C
Silkscreen Top
Pantone 200C
Silkscreen Top
Vtech Silver 04
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
Silkscreen Rear
Translucent
Vtech Silver 04
Silkscreen Rear
Pantone 433C
Silkscreen Rear
Vtech Silver 04
FrontCrystal KeysCrystal KeysCrystal Keys
Silkscreen Rear
Vtech Silver 04
Crystal Keys
Back
Engraved
0.3mm
Watermark
Front
Silkscreen Top
Pantone 347C
Silkscreen Top
Pantone 200C
Silkscreen Top
Vtech Silver 04
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
SILKSCREEN ARTWORK | VG208 - Handset
Ari | 21 June 2021 | Revision 1.0
Silkscreen Rear
Translucent
Vtech Silver 04
Silkscreen Rear
Pantone 433C
Silkscreen Rear
Vtech Silver 04
FrontCrystal KeysCrystal KeysCrystal Keys
Silkscreen Rear
Vtech Silver 04
Crystal Keys
Back
Engraved
0.3mm
Watermark
Front
Silkscreen Top
Pantone 347C
Silkscreen Top
Pantone 200C
Silkscreen Top
Vtech Silver 04
-
1
-
2
VTech VG208 Guide de démarrage rapide
- Catégorie
- Téléphones
- Taper
- Guide de démarrage rapide
dans d''autres langues
- English: VTech VG208 Quick start guide
Documents connexes
-
VTech CS5229-4 Mode d'emploi
-
VTech CS5329-3 Guide de démarrage rapide
-
VTech CS5249 Guide de démarrage rapide
-
-
VTech IS8121 Mode d'emploi
-
-
-
-