VTech RM7756 Guide de démarrage rapide

Marque: VTech

Modèle: RM7756

Catégorie: Moniteurs vidéo bébé

Taper: Guide de démarrage rapide

Congratulations

on purchasing your new VTech product.

Before using this baby monitor, please read the Important safety instructions.

For support, shopping, and everything new at VTech, visit our website at

www.vtechphones.com. In Canada, visit www.vtechcanada.com.

Frequency Baby unit: 2412 - 2462 MHz

Channels 11

LCD 7’’ Color LCD

(IPS 1280x800 pixels)

Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may

vary according to environmental conditions at the time of use.

Power requirement Baby unit power adapter: Output: 5V DC, 1000mA.

Parent unit power adapter: Output: 5V DC, 2A.

Parent unit battery: 3.7V 5000mAh, 18.5Wh Lithium-ion battery

Specifications are subject to change without notice.

Technical specications

RM7756HD

RM7756-2HD

7” Smart Wi-Fi 1080p

Video Monitor

What does HD Video Monitor do?

Quick start guide

VTech 7” Smart Wi-Fi 1080p Video Monitor allows you to stay close to your baby when you

are on the move or away. This monitor is Wi-Fi enabled, using your home wireless network

to stream live video and audio through the 1080p baby unit and 7-inch color screen

parent unit. It allows you to maintain a constant connection to your baby.

You can also monitor from your smartphone and mobile tablet.

VTech 7” Smart Wi-Fi 1080p Video Monitor uses MyVTech Baby Pro app to let you

instantly see and hear what’s happening with your baby from anywhere in the world. The

app can be downloaded from the App Store or the Google PlayTM Store.

Disclaimer and Limitation of Liability

VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss resulting

from the use of this user’s manual. VTech Communications, Inc. and its suppliers assume no responsibility

for any loss or claims by third parties that may arise through the use of this product.

Company: VTech Communications, Inc.

Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States

Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada

UL STD.

62368-1

CERTIFIED TO

CSA STD.

C22.2 NO.62368-1

CONFORMS TO

Android TM and Google Play TM are trademarks of Google Inc.

App Store is a trademark of Apple Inc., registered in the U.S. and other countries.

IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.

Go to www.vtechphones.com

to register your product for

enhanced warranty support and

latest VTech product news.

RM7756HD RM7756-2HD

For more support information

Direct mode

The parent unit and the baby unit of your video monitor connect to each others in Direct mode

by default, which allows you to stream live video right out of the box. Direct mode connection

lets you stream live video from parent unit only.

• You may experience reduced signal strength if your parent unit and baby unit are far apart, or there are

obstructing factors, such as internal walls, between them. Move the parent unit closer to the baby unit to

improve the signal strength.

Wi-Fi Router mode

To stream live video with better

connection, you can also set up your

monitor in Router mode connection.

Router mode uses your home Wi-Fi

network to connect the video monitor.

It supports streaming live video through

the parent unit and MyVTech Baby Pro

app.

Download and install the MyVTech Baby

Pro mobile app to stream remotely. With

the mobile app, your Wi-Fi router (not

included) serves as a communicating

channel between your baby unit and

mobile device, allowing you to monitor

and control your baby unit wherever you

are. For details, see Download app for mobile access section in this quick start guide.

• When both parent unit and app are viewing the camera simultaneously, the video quality will be

optimised to deliver the best possible viewing result.

Overview

What’s in the box

Connect, charge and power on the baby monitor

x 2 x 2

Quick start guide

Your baby monitor package contains the following items. Save your sales receipt and original

packaging in the event warranty service is necessary.

How the system works Parent unit icons

For mobile access:

MyVTech Baby Pro mobile app

Network Wi-Fi

Wi-Fi router 2.4GHz 802.11 b/g/n

Internet connection 1.5 Mbps @ 720p or 2.5 Mbps @1080p upload

bandwidth per baby unit

Requirements

Main

Menu Options

Monitoring mode (* For RM7756-2HD only)

• View baby units in Single mode.

• View baby units in Patrol mode.

• View baby units in Split screen.

Night light

• Turn on or turn off night light.

• Select a night light color.

• Adjust night light brightness.

• Set a night light timer.

Melodies and soothing sounds

• Select play all melodies, or play

one of the ﬁve melodies and ﬁve

soothing sounds.

• You can also set the timer to

stop playing after 15, 30 or 60

minutes, or playing non-stop.

Alerts - Sound, motion and temperature

• Select the sound and motion

sensitivity level.

• Turn on/off sound and motion

detection alerts.

• Select maximum and minimum

temperature for alert range.

• Turn on/off temperature alert.

• Turn on/off Auto Wake Up

function.

Parent unit settings

• Adjust parent unit screen

brightness.

• Adjust Low Battery Alert Tone.

• Adjust No Link Alert Tone.

• Turn on/off Dim mode.

Baby unit settings

• Turn on/off Night Vision.

• Turn on/off baby unit Status LED.

• Adjust baby unit speaker volume.

Main

Menu Options

General settings

• Conﬁgure Wi-Fi.

• Connect mobile phone.

• Reset Settings to factory default.

• Software Update.

Connect the baby monitor

• Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the

baby’s crib or playpen.

• The rechargeable battery in the parent unit is built-in.

• Use only the power adapters supplied with this product.

• Make sure the parent unit and the baby unit are not connected to the switch controlled electric outlets.

• Connect the power adapters in a vertical or ﬂoor mount position only. The adapters’ prongs are not

designed to hold the weight of the parent unit and the baby unit, so do not connect them to any ceiling,

under-the-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.

• Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children.

Charge the parent unit battery before use

The parent unit runs on rechargeable battery or AC power. To continuously monitor your

baby, keep the parent unit connected to AC power.

• Before using the baby monitor for the ﬁrst time, charge the parent unit battery for 12 hours. When

the parent unit battery is fully charged, the battery icon becomes solid .

• The standby time varies depending on your actual use.

After the parent unit is fully charged, press Power until the welcoming screen appears.

The battery icon indicates the battery status (see the following table).

Battery indicators Battery status Action

The screen displays and .

The LED light ﬂashes.

The battery has very little

charge and may be used

for only a short time.

Charge

without

interruption

(about 30

minutes).

The battery icon becomes solid . The battery is fully

charged. To keep the battery

charged, connect it to AC

power when not in use.

1 set for RM7756HD

2 sets for RM7756-2HD

Slide the switch to ON to power on your baby unit.

• When powering up, the baby unit’s status LED turns on.

It will turn off after a while and keeps off.

• The status LED is set to off by default. If you want to

keep the LED on, press MENU, then go to

> Status LED and turn it on.

NOTE:

Camera lens and surface may get

warm during normal operation.

WARM

Parent unit overview

1LINK LED light

• On when the parent unit is linked to the

baby unit.

• Flashes when the link to the baby unit

is lost.

2 LED light

• On when the parent unit is connected to

AC power, and the battery is charging.

• Flashes when the parent unit battery is

low and needs to be charged.

33- level sound indicator light

• Green: low sound level is detected by

the baby unit.

• Green and amber: moderate sound

level is detected by the baby unit.

• Green, amber and red: high sound level

is detected by the baby unit.

4TALK /

• Press and hold to talk to the baby unit.

• While in a sub-menu, press to exit.

5MENU | SELECT

• Press to enter the main menu.

• While in a menu, press to choose an

item, or save a setting.

6 | | | Arrow keys

• Press to navigate leftward, upward,

rightward or downward, within the

main menu and sub-menus.

• While viewing a zoomed image, press

to move the image leftward, upward,

rightward or downward.

7 |

• Increase or decrease parent unit

volume.

8 Zoom

• Press to zoom in/out.

• While in a sub-menu, press to view the

help menu.

9 Power | LCD ON/OFF

10 Microphone

11 Antenna

12 Speaker

13 Power jack

14 RESET

• Force reboot the parent unit.

15 Stand

Mobile access

Connecting Wi-Fi to

enhance local access

Install MyVTech Baby Pro mobile app

1. Browse the App Store or the Google Play store .

2. Search for the mobile app with the keyword “myvtech baby pro“.

3. Download and install the MyVTech Baby Pro mobile app to your mobile device.

Scan the QR codes on the right to get the app.

• Make sure your mobile device meets the minimum

requirement for the mobile app.

Minimum requirement

The mobile app is compatible with:

• AndroidTM 6.0 or later; and

• iOS 12 or later.

Download the free MyVTech Baby Pro mobile app and install it to a

mobile device, then use your mobile device and the mobile app to

monitor your areas remotely.

1. Press MENU when the parent unit is idle.

2. Go to > Connect Mobile Phone.

3. Scan the QR code in the parent unit to download the app into your

mobile device.

4. Follow the instructions in the mobile app to set up and pair your baby

unit to the mobile app.

Alternatively, you can download the mobile app from the App Store or

Google Play store.

Download app for mobile access

After installing the mobile app, follow the instructions in the mobile app and parent

unit to set up and pair your baby unit.

In your mobile device:

1. Tap to run the mobile app in your mobile device, and then create a user account.

2. We recommend that you use common webmail services, such as Google Gmail for

registration of your user account. Check your email (and Spam folder), and activate

your new camera account via the email link, then sign in to your account.

3. Follow the instructions in the mobile app to pair the camera. Tap , then Add Camera

in the mobile app to get started.

The applied nameplate is located at the bottom of the baby unit’s base.

When using your equipment, basic safety precautions should

always be followed to reduce the risk of ﬁre, electric shock and

injury, including the following:

1. Follow all warnings and instructions marked on the product.

2. Adult setup is required.

3. CAUTION: Do not install the baby unit at a height above 6.5

feet (2 meters).

4. This product is intended as an aid. It is not a substitute for

responsible and proper adult supervision and should not be

used as such.

5. This product is not intended for use as a medical monitor.

6. Do not use this product near water. For example, do not use

it next to a bath tub, wash bowl, kitchen sink, laundry tub or

swimming pool, or in a wet basement or shower.

7. CAUTION: Use only the battery provided. There may be a risk

of explosion if a wrong type of battery is used for the parent

unit. The battery cannot be subjected to high or low extreme

temperature and low air pressure at high altitude during use,

storage or transportation. Disposal of battery into ﬁre or a hot

oven, or mechanically crushing or cutting or the battery can

result in an explosion. Leaving the battery in an extremely

high temperature surrounding environment can result in an

explosion or the leakage of ﬂammable liquid of gas. Battery

subjected to extremely low air pressure may result in an

explosion or the leakage of ﬂammable liquid or gas. Dispose

of used battery according to the information in The RBRC seal.

8. Use only the adapters included with this product. Incorrect

adapter polarity or voltage can seriously damage the product.

Power adapters information:

Baby Unit Output: 5V DC 1000mA

VTech Telecommunications Ltd.

Model: VT05EUS05100

Parent Unit Output: 5V DC 2A

VTech Telecommunications Ltd.

Model: VT07EUS05200

Rechargeable battery information:

3.7V 5000mAh, 18.5Wh Lithium-ion battery

Zhuhai Great Power Energy Co., Ltd.

Model: GSP806090-5Ah-3.7V-1S1P

9. The power adapter is intended to be correctly oriented in a

vertical or ﬂoor mount position. The prongs are not designed

to hold the plug in place if it is plugged into a ceiling, under-

the-table or cabinet outlet.

10. For pluggable equipment, the socket-outlet (power adapter)

shall be installed near the equipment and shall be easily

accessible.

11. Unplug this product from the wall outlet before cleaning.

Do not use liquid or aerosol cleaners. Use a damp cloth for

cleaning.

12. Do not cut off the power adapters to replace them with other

plugs, as this causes a hazardous situation.

13. Do not allow anything to rest on the power cords. Do not

install this product where the cords may be walked on or

crimped.

14. This product should be operated only from the type of power

source indicated on the marking label. If you are not sure of

the type of power supply in your home, consult your dealer or

local power company.

15. The equipment is to be supplied from an identiﬁed USB port

complying with the requirements of Limited Power Source.

16. Do not overload wall outlets or use an extension cord.

17. Do not place this product on an unstable table, shelf, stand or

other unstable surfaces.

18. This product should not be placed in any area where proper

ventilation is not provided. Slots and openings in the back or

bottom of this product are provided for ventilation. To protect

them from overheating, these openings must not be blocked

by placing the product on a soft surface such as a bed, sofa

or rug. This product should never be placed near or over a

radiator or heat register.

19. Never push objects of any kind into this product through

the slots because they may touch dangerous voltage points

or create a short circuit. Never spill liquid of any kind on the

product.

20. To reduce the risk of electric shock, do not disassemble this

product, but take it to an authorized service facility. Opening

or removing parts of the product other than speciﬁed access

doors may expose you to dangerous voltages or other risks.

Incorrect reassembling can cause electric shock when the

product is subsequently used.

21. You should test the sound reception every time you turn on

the units or move one of the components.

22. Periodically examine all components

for damage.

23. There is a very low risk of privacy loss when using certain

electronic devices, such as baby monitors, cordless

telephones, etc. To protect your privacy, make sure the

product has never been used before purchase, reset the baby

monitor periodically by powering off and then powering on

the units, and power off the baby monitor if you will not use it

for some time.

24. Children should be supervised to ensure that they do not play

with the product.

25. The small parts of this monitor can be swallowed by babies or

small children. Keep these parts out of reach of children.

26. The product is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have

been given supervision or instruction concerning use of the

appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

• Use and store the product at a temperature between 32oF and

104oF.

• Burn hazard, ﬁre hazard, explosion hazard associated with

mishandling of the battery.

• Do not expose the product to extreme cold, heat or direct

sunlight. Do not put the product close to a heating source.

• Warning—Strangulation Hazard—Children

have STRANGLED in cords. Keep this cord out of

the reach of children (more than 3 ft (0.9m) away).

Do not remove this tag.

• Never place the camera unit(s) inside the baby’s crib or

playpen. Never cover the camera unit(s) or parent unit with

anything such as a towel or a blanket.

• Other electronic products may cause interference with your

camera unit. Try installing your camera unit as far away from

these electronic devices as possible: wireless routers, radios,

cellular telephones, intercoms, room monitors, televisions,

personal computers, kitchen appliances and cordless

telephones.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent

research entity, led a multidisciplinary evaluation of the

interference between portable wireless devices and implanted

cardiac pacemakers. Supported by the U.S. Food and Drug

Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches from the

pacemaker.

• Should NOT place wireless devices directly over the

pacemaker, such as in a breast pocket, when it is turned ON.

WTR’s evaluation did not identify any risk to bystanders with

pacemakers from other persons using wireless devices.

Electromagnetic ﬁelds (EMF)

This VTech product complies with all standards regarding

electromagnetic ﬁelds (EMF). If handled properly and according

to the instructions in this user’s manual, the product is safe to be

used based on scientiﬁc evidence available today.

Important safety instructions

Raise the parent unit

antenna for better

reception

Press and hold

Status icons

Direct mode

Parent unit, baby unit 1 and baby unit 2

(*For RM7756-2HD only) are connected

to each others directly.

Wi-Fi Router mode

Parent unit, baby unit 1 and baby unit 2

(*For RM7756-2HD only) are connected to

home Wi-Fi network.

Baby unit 1 and 2 are being viewed in

Patrol mode (*For RM7756-2HD only).

Baby unit 1 and 2 are being viewed in

Split mode (*For RM7756-2HD only).

Night vision is turned on.

Motion detection alert is turned on.

Sound detection alert is turned on.

Melodies and soothing sounds are

playing.

Night light is turned on.

Auto night light brightness is activated.

Temperature alert is turned on.

Parent unit is muted.

Battery indicator.

Local access

Baby unit overview

1Light sensor

2Camera lens

3Infrared LEDs

• Allow you to see clearly in a dark environment.

4Microphone

5Night Light

6 Night Light Control Key

• Go to Night Light section to learn more.

7ON/OFF switch

• Power it on or off.

8LED indicator

• Red is steadily on when the baby unit is

connecting to the parent unit in direct mode.

• Green is steadily on when the baby unit is

connected in Wi-Fi router mode.

• Red ﬂashes slowly during video streaming in

direct mode.

• Green ﬂashes slowly during video streaming

in Wi-Fi router mode.

9Speaker

10 Temperature sensor

11 PAIR

• Press and hold for three seconds to enter

pairing mode.

• Reset the baby unit to factory default.

1. Press and hold PAIR key until you hear a

beep sound.

2. Release the PAIR key, and then press the

PAIR key again ﬁve times until you hear

another beep sound.

3. The baby unit will sound another beep

when the reset completes. Then, the

baby unit will reboot.

12 Power jack

13 Wall mount slots

To ensure that your baby monitor is always at its best performance, the parent unit will

prompt you to update its software and the baby unit ﬁrmware when there are new versions

available.

• Follow the instructions on the parent unit screen to update your baby monitor. If you skip

the updates, the parent unit and baby unit will be updated automatically when the parent

unit is powered off, and then powered on again.

• To check if your device is running on the latest software or to update your device software, go to:

> Software Update

Connect your baby monitor to Wi-Fi

• You must connect your video monitor to your secured home Wi-Fi network in order to receive

the latest software and ﬁrmware updates. To set it up, go to:

> Conﬁgure Wi-Fi

Auto software and rmware update

Night Light

On the baby unit:

You can control the night light remotely on the parent unit or directly on the baby unit.

On the parent unit:

1. Press MENU.

2. Press or to scroll to Night Light

menu, then press MENU or to enter.

3. Press or to choose below options:

Night Light Control Key

Single Tap: Turn on/off

Tap and hold: Adjust night light brightness

Turn on/off night light

Change night light color

Adjust night light brightness

Set night light timer

To keep this product working well and looking good, follow these guidelines:

• Avoid placing it near heating appliances and devices that generate electrical noise (for example,

motors or ﬂuorescent lamps).

• DO NOT expose it to direct sunlight or moisture.

• Avoid dropping the product or treating it roughly.

• Clean with a soft damp cloth.

• DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap.

• DO NOT use cleaning spray or liquid cleaners.

• Make sure the parent unit and the baby unit are dry before you connect them to the mains again.

• Clean the USB charging port of dust, dirt, and lint regularly.

When you are not going to use the video monitor for some time, store the parent unit, the baby unit

and the adapters in a cool and dry place.

Below are the questions most frequently asked about the video monitor.

Can I turn the parent

unit display screen

off but keep hearing

sounds from the baby

unit?

Yes, press | LCD ON/OFF on the parent unit to turn off the screen. The parent

unit display will also dim automatically after being inactive for some time. In both

instances, you will still be able to hear all sounds from the baby unit.

Press any key to turn the screen back on.

Why is the baby

unit not responding

normally?

Try the following (in the order listed) for a common cure:

1. Disconnect the power to the baby unit.

2. Wait a few minutes before connecting power back to the baby unit.

3. Reboot the parent unit.

Why is my screen in

black and white?

The baby unit has a light sensor that measures ambient light. When the

ambient light is dim, such as during night time or in a dark room, the baby unit

activates its infrared LEDs, and displays the camera images in black and white

night vision.

Why does my baby unit

show ofﬂine? Why is the

connection lost every

now and then?

The baby unit may have lost connection to the Wi-Fi router. Check your

network and router settings.

Other electronic products may cause interference with your baby unit. Try

installing your baby unit as far away from these electronic devices as possible.

Why can’t I hear a

sound/Why can’t I hear

my baby crying?

The parent unit speaker volume may be too low. Press on the parent unit

to increase the volume.

You may have set a low sound sensitivity level. Set the sound sensitivity to a

higher level. For details, go to www.vtechphones.com for online help topics.

Frequently asked questions

General product care

Storage

Test the sound level and position the baby monitor

Basic operation

If you plan to install your baby unit in a designated

location, and use your home Wi-Fi network to

connect your video monitor, you need to test

which of your selected monitoring areas within the

house have good Wi-Fi signal strength. After you

have powered on your parent unit, you can use

your parent unit’s Wi-Fi signal strength indicator

to assist in checking. Once you have identiﬁed the

suitable location, you can install your baby unit.

Adjust the distance between your baby unit and

the Wi-Fi router if needed.

• Depending on surroundings and obstructing factors,

such as the effect distance and internal walls have on

signal strength, you may experience reduced Wi-Fi

signal. To improve the Wi-Fi signal strength, adjust the

distance or direction of your parent unit. Check with

your parent unit again.

test the location for the baby unit

Talk to your baby via the baby unit

1. Press and hold the TALK key.

2. When the icon displays on

screen, speak to your parent unit.

Your voice is transmitted to the

baby unit.

3. When ﬁnished talking, release

the TALK key to hear your baby

again.

Turn on/off baby unit's status LED

Turn on or turn off the baby unit status LED

indicator. Go to:

> Status LED.

Zoom

Press to zoom in or out in a ﬁxed

zoom sequence. indicates that the

image is magniﬁed 3 times.

Adjust speaker volume

Press | to adjust the parent unit

speaker volume level received from the

baby unit.

After powering up your video monitor, the parent unit streams live video in direct mode.

We recommend you follow the instructions on screen to set up home Wi-Fi network

with your monitor for functionality enhancements and mobile access. See Auto software

and ﬁrmware update and Download app for mobile access in this quick start guide.

Use the menu

Press MENU on the parent unit to enter the

main menu, choose a menu item, or save a

setting. You can use the parent unit menu

for advanced settings or operations, such

as to play or stop the baby unit lullaby, or

adjust the baby unit sound sensitivity.

While in the menu:

• Press | | | to scroll among the

menu options.

• Press SELECT to select an item.

• Press TALK to return to the live video.

• Press to go to the Help & info page.

You can reset the parent unit by pressing the

RESET key at the back of the unit.

Insert a pin into the RESET hole on the back of

the parent unit, and then press the key inside.

Turn on/off the parent unit screen

You can turn on or turn off the parent unit

screen without powering off the unit. You

will still hear sounds from the baby unit.

• Press | LCD ON/OFF on the parent unit

to turn off the screen.

• Press any key on the parent unit to turn

the screen on again.

Testing the sound level of the baby monitor

• This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and should

not be used as such.

• For hearing protection, make sure the parent unit is more than 3 feet away from the baby

unit. If you hear any high-pitched noise from the parent unit, move the parent unit further

until the noise stops. You can also press on the parent unit to lower or mute the noise.

• Increase the parent unit speaker volume if you cannot hear the sounds transmitted from the baby unit.

< 3ft (1m)

> 3ft (1m)

Muted

Press and hold

For RM7756-2HD only

Monitoring Modes

When more than one baby unit is paired to the parent unit, you can choose to view

different baby units in three monitoring modes. Learn more about each below:

Change the monitoring mode:

1. Press MENU when the parent unit is idle.

2. Press MENU or to enter Monitoring Mode menu.

3. Press or to choose between Single , Split , and Patrol monitoring

mode options. Press SELECT to conﬁrm.

Single Mode

The screen displays images only from the selected baby

unit in full screen.

Split Mode The screen displays images from all paired baby units at

the same time in split view.

Patrol Mode The screen displays a single cam view that transitions to a

different baby unit every 10 seconds.

2. Adjust the angle of the baby unit to aim

at your baby.

1. Place the baby unit more than 3 feet away

from your baby.

3. To avoid causing high-pitched screeching noise from your baby monitor:

• Make sure your baby unit and parent unit are more than 3 feet apart; OR

• Turn down the volume of your parent unit.

Positioning the baby monitor

• Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the baby’s

crib or playpen.

Driven by system updates, the software, online help topics, and online FAQs will be

updated periodically.

For operations and guides to help you using your HD video monitor, and for latest

information and supports, go and check the online help topics and online FAQs.

Use your smartphone or mobile device to access our online help.

Go to https://help.vtechphones.com/RM7756HD or

https://help.vtechphones.com/RM7756-2HD;OR Scan the QR code on the right.

Launch the camera app or QR code scanner app on your smartphone or tablet. Hold

the device’s camera up to the QR code and frame it. Tap the notiﬁcation to trigger

the redirection of the online help.

- If the QR code is not clearly displayed, adjust your

camera’s focus by moving your device closer or

further away until it is clear.

If you would like to contact us, visit

https://help.vtechphones.com/cs or scan the QR code.

You can also call our Customer Support at 1-844-848-8324 (1-844-84-VTECH) [in US]

or 1-888-211-2005 [in Canada] for help.

Need help?

RM7756-2HD

RM7756HD

Press and hold

> 3ft

mount the baby unit (optional)

1. Place the wall mount bracket on a

wall and then use a pencil to mark

two holes in parallel. Remove the

wall mount bracket and drill two

holes in the wall (5.5mm drill bit).

NOTESNOTE

Notes

• Check for reception strength and

camera angle of the baby unit before

drilling the holes.

• The types of screws and plugs you need

depend on the composition of the wall.

You may need to purchase the screws

and plugs separately to mount your

baby units.

2. If you drill the holes into a stud, go

to step 3.

• If you drill the holes into an

object other than a stud, insert

the wall plugs into the holes.

Tap gently on the ends with a

hammer until the wall plugs are

ﬂush with the wall.

3. Align the wall mount bracket and screws with

the holes in the wall as shown. Tighten the screw

in the middle hole ﬁrst, so that the wall mount

bracket position is ﬁxed. You can tighten the

other screw in the top hole.

3. Insert the screws into the holes and

tighten the screws until only 6.5mm inch

of the screws are exposed.

4. Place the baby unit on the wall

mount bracket, and then slide it

forward until it locks into place. Align

the holes on the wall mount bracket

with the screws on the wall, and slide

the wall mount bracket down until it

locks into place.

5. You can maximize your baby unit viewing angles by tilting the wall mount bracket.

Hold the baby unit, and then rotate the knob in an anticlockwise direction. This will loosen the joint of the wall mount bracket.

Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob in a clockwise direction to tighten the

joint and secure the angle.

4. Place the baby unit on the wall mount bracket,

and then slide it forward until it locks into place.

Connect the power adapter to the baby unit .

CABLE MANAGEMENT

VTech cares about your privacy and peace of mind. That’s why we’ve put together a list of industry-

recommended best practices to help keep your wireless connection private and your devices protected

when online. We recommend you carefully review and consider complying with the following tips.

Ensure your wireless connection is secure.

• Before installing a device, ensure your router’s wireless signal is encrypted by selecting the “WPA2-

PSK with AES” setting in your router’s wireless security menu.

Change default settings.

• Change your wireless router’s default wireless network name (SSID) to something unique.

• Change default passwords to unique, strong passwords. A strong password:

- Is at least 10 characters long.

- Is complex.

- Does not contain dictionary words or personal information.

- Contains a mix of uppercase letters, lowercase letters, special characters and numbers.

Keep your devices up to date.

• Download security patches from manufacturers as soon as they become available. This will ensure

you always have the latest security updates.

• If the feature is available, enable automatic updates for future releases.

Disable Universal Plug and Play (UPnP) on your router.

• UPnP enabled on a router can limit the effectiveness of your ﬁrewall by allowing other network

devices to open inbound ports without any intervention or approval from you. A virus or other

malware program could use this function to compromise security for the entire network.

For more information on wireless connections and protecting your data, please review the following

resources from industry experts:

1. Federal Communications Commission: Wireless Connections and Bluetooth Security Tips –

www.fcc.gov/consumers/guides/how-protect-yourself-online.

2. U.S. Department of Homeland Security: Before You Connect a New Computer to the Internet –

www.us-cert.gov/ncas/tips/ST15-003.

3. Federal Trade Commission: Using IP Cameras Safely –

https://www.consumer.ftc.gov/articles/0382-using-ip-cameras-safely.

4. Wi-Fi Alliance: Discover Wi-Fi Security –

http://www.wi-ﬁ.org/discover-wi-ﬁ/security.

Protect your privacy and online security

1 2 3

FCC and IC regulations

FCC Part 15

NOTE: This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of

the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modiﬁcations to this equipment not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a

user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC

criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of approximately 8 in

(20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face.

This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B)

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s

licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must

accept any interference, including interference that may cause undesired operation of the device.

The term ‘’IC:‘’ before the certiﬁcation/registration number only signiﬁes that the Industry Canada technical speciﬁcations were met.

This product meets the applicable Innovation, Science and Economic Development Canada technical speciﬁcations.

RF radiation exposure statement

The product complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be

installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons’ body. Use of other accessories

may not ensure compliance with FCC RF exposure guidelines. This equipment complies also with Industry Canada RSS-102 with respect

to Canada’s Health Code 6 for Exposure of Humans to RF Fields.

La plaque signalétique appliquée est située au bas du socle de

l’unité du bébé.

Lorsque vous utilisez votre appareil, vous devriez toujours suivre

certaines mesures de précaution de base aﬁn de réduire les risques

d’incendie, d’électrocution et de blessures corporelles, dont ceux

qui suivent:

1. Observez toutes les instructions et mises en garde inscrites sur

l’appareil.

2. L’installation par un adulte est requise.

3. MISE EN GARDE: N’installez pas l’unité du bébé à une hauteur

supérieure à 2 mètres.

4. Ce produit a été conçu pour être un dispositif d’appoint

seulement. Il n’est pas le remplacement d’une supervision

responsable et adéquate par un adulte et ne devrait pas être

utilisé comme telle.

5. Ce produit n’est pas conçu pour être utilisé en tant que moniteur

médical.

6. N’utilisez pas cet appareil près de l’eau ni de toute autre source

d’humidité, par exemple, près d’une baignoire, cuve à lessive,

évier de cuisine, dans un sous-sol humide ni près d’une piscine,

dans un soussol humide ou une douche.

7. MISE EN GARDE: Utilisez uniquement la pile fournie. Un

risque d’explosion pourrait survenir si un mauvais type de

pile est utilisé pour l’unité du parent. La pile ne peut pas être

soumise à des températures extrêmes élevées ou basses et à

une faible pression d’air à haute altitude pendant l’utilisation,

l’entreposage ou le transport. L’élimination de la pile dans le

feu ou dans un four chaud, ou l’écrasement ou le découpage

mécanique de la pile peuvent entraîner une explosion. Laisser

la pile dans un environnement à température extrêmement

élevée peut entraîner une explosion ou la fuite d’un liquide ou

d’un gaz inﬂammable. Une pile soumise à une pression d’air

extrêmement basse peut provoquer une explosion ou une

fuite de liquide ou de gaz inﬂammable. Éliminer la pile usagée

conformément aux informations du Sceau RBRC.

8. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation

d’un adaptateur dont la polarité ou la tension serait inadéquate

risque d’endommager sérieusement le produit et mettre votre

sécurité en péril.

Informations sur les adaptateurs électriques :

Sortie : 5 V CC 1000mA.

VTech Telecommunications Ltd.

Modèle : VT05EUS05100

Sortie : 5 V CC 2A.

VTech Telecommunications Ltd.

Modèle : VT07EUS05200

Informations sur les piles rechargeables :

3.7V 5000mAh, 18.5Wh Lithium-ion batterie

Zhuhai Great Power Energy Co., Ltd.

Modèle : GSP806090-5Ah-3.7V-1S1P

9. Lorsqu’ils sont branchés dans une prise de courant, les

adaptateurs secteur ont été conçus pour être orientés

correctement, soit à la verticale ou au plancher. Les broches

n’ont pas été conçues pour supporter le poids du bloc

d’alimentation et le maintenir en place si celuici est branché dans

une prise au plafond, sous une table ou dans un meuble.

10. Pour les appareils raccordés, la prise de courant (de l’adaptateur

secteur) doit être installée près de l’équipement et doit être

facilement accessible.

11. Débranchez ce produit de la prise de courant avant de

procéder au nettoyage. N’utilisez pas de nettoyants en aérosols.

Utilisez un chiffon humide pour le nettoyer.

12. Ne coupez pas les cordons d’alimentation pour remplacer les

ﬁches, car ceci peut présenter un danger potentiel.

13. Ne laissez aucun objet reposer ni appuyer sur le cordon

d’alimentation. N’installez pas cet appareil dans un endroit où

l’on risque d’écraser le cordon d’alimentation ou de le piétiner.

14. Ne faites fonctionner cet appareil qu’avec le type d’alimentation

indiqué sur l’étiquette. Si vous ne connaissez pas le type

d’alimentation que vous possédez à votre domicile, consultez

votre marchand ou votre compagnie locale d’électricité.

15. L’équipement doit être fourni à partir d’un acquiescement

gauche identiﬁé d’USB aux conditions de la source d’énergie

limitée.

16. Ne surchargez pas les prises de courant murales ni les rallonges

électriques.

17. Ne placez pas cet appareil sur un chariot, meuble, trépied,

support de montage ni table chancelants.

18. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil

ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de

surchauffer, ne bloquez sous aucun prétexte ces ouvertures et

n’empêchez pas l’aération adéquate de l’appareil en le plaçant

sur un lit, divan, tapis ou toute autre surface similaire. De même,

ne le positionnez pas à proximité ni au-dessus d’une source de

chaleur ou d’un calorifère. De plus, ne placez pas l’appareil dans

un endroit avant de vous assurer qu’il y ait une bonne circulation

d’air.

19. N’enfoncez jamais d’objets à travers les ouvertures de cet

appareil, car ils pourraient entrer en contact avec des points de

tension dangereux ou causer des courts-circuits qui peuvent

dégénérer en incendies ou en risques d’électrocution. Ne

renversez jamais de liquide dans ce produit.

20. Aﬁn de réduire les risques d’électrocution, ne démontez pas cet

appareil, mais apportez-le dans un centre de service autorisé.

L’ouverture du boîtier ou le retrait de toutes pièces que contient

cet appareil, à l’exception de l’accès autorisé à certaines portes

ou ouvertures, risque de vous exposer à des points de tension

dangereux ou d’autres dangers. Un remontage incorrect peut

par la suite présenter des risques d’électrocution.

21. Vous devriez tester la réception chaque fois que vous mettez

l’appareil en fonction.

22. Examinez les composantes aﬁn de vériﬁer si celles-ci ne sont pas

endommagées.

23. Il existe un très faible risque de perte de conﬁdentialité

avec certains appareils électroniques (autres écoute-bébés,

téléphones sans ﬁls etc.). Pour l’éviter, s’assurer que le produit

n’a jamais été utilisé avant l’achat, réinitialiser l’unité de façon

périodique, éteindre l’écoute-bébé quand il n’est pas en cours

d’utilisation.

24. Les enfants devraient être supervisés aﬁn de vous assurer qu’ils

ne jouent pas avec l’appareil.

25. Les petites pièces de ce moniteur peuvent être avalées par les

bébés ou les petits enfants. Veuillez tenir ces pièces hors de

portée des enfants.

26. Le produit n’est pas conçu pour être utilisé par des personnes

(incluant des enfants) aux capacités physiques, sensorielles

ou mentales réduites ou qui manquent d’expérience et de

connaissances, à moins qu’on leur ait donné sufﬁsamment

de supervision ou d’instructions relativement à l’utilisation de

l’appareil par une personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

• Utilisez et entreposez le produit à une température entre 0˚ C

(32˚F) et 40˚C (104˚ F).

• Risque de brûlure, risque d’incendie, risque d’explosion associé

à une mauvaise manipulation de la batterie.

• N’exposez pas cet appareil à des froids ou des chaleurs

extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez pas

près d’une source de chauffage.

• Avertissement - Risque de strangulation -

Les enfants se sont ÉTRANGLÉS dans des cordons.

Gardez ce cordon hors de portée des enfants (à plus

de 0,9 m). N’enlevez pas cette étiquette.

• Ne jamais placer le moniteur à l’intérieur du berceau ou du parc

de bébé. Ne jamais couvrir le moniteur ou l’unité (s) portative

avec un article tel une serviette ou une couverture.

• D’autres produits électroniques peuvent causer des

interférences auprès de votre caméra IP. Essayez d’installer

votre caméra IP le plus loin possible de ces dispositifs

électroniques : routeurs sans ﬁl, radios, téléphones cellulaires,

interphones, moniteurs de pièces, téléviseurs, ordinateurs

personnels, appareils électriques de cuisine et téléphones sans

ﬁl.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux dispositifs

numériques sans ﬁl):

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une

ﬁrme de recherche indépendante, a mené une évaluation

pluridisciplinaire des interférences entre les téléphones sans ﬁl

portatifs et les stimulateurs cardiaques implantés dans l’organisme.

Appuyée par l’Administration des aliments et drogues (FDA) des

États-Unis, la ﬁrme WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

• Vous devriez maintenir les dispositifs sans ﬁl à au moins six

pouces du simulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans ﬁl directement sur

le stimulateur cardiaque, tel que dans une poche de chemise,

lorsque celui-ci est en marche.

L’étude effectuée par l’organisme WRS n’a pas identiﬁé de risque

pour les détenteurs de simulateurs cardiaques causés par les gens

qui utilisent dispositifs sans ﬁl à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de VTech est conforme à toutes les normes se rapportant

aux champs électromagnétiques (EMF) standard. Si vous le

manipulez correctement en suivant les instructions de ce guide, son

utilisation sera sécuritaire pendant de nombreuses années, selon les

meilleures évidences scientiﬁques dont nous disposons aujourd’hui.

California Energy Commission battery

charging testing mode

This video monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your video monitor is set up to

comply with the energy-conserving standards right out of the box.

Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging.

Even if the parent unit is paired to camera units, the CEC battery charging testing mode is activated while it is powered off and

charging.

For cETL compliance only

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the

holder of a valid proof of purchase (“Consumer” or “you”)

that the Product and all accessories provided in the sales

package (“Product”) are free from defects in material

and workmanship, pursuant to the following terms and

conditions, when installed and used normally and in

accordance with the Product operating instructions. This

limited warranty extends only to the Consumer for Products

purchased and used in the United States of America and

Canada.

What will VTech do if the Product is not free from defects

in materials and workmanship during the limited warranty

period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service

representative will replace at VTech’s option, without charge,

a Materially Defective Product. If we choose to replace

the Product, we may replace it with a new or refurbished

Product of the same or similar design. We will retain

defective parts, modules, or equipment. Replacement of the

Product, at VTech’s option, is your exclusive remedy. VTech

will return the replacement Products to you in working

condition. You should expect the replacement to take

approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE

(1) YEAR from the date of purchase (90 days on products

purchased as Refurbished*). This limited warranty also

applies to the replacement Product for a period of either (a)

90 days from the date the replacement Product is shipped

to you or (b) the time remaining on the original one-year

warranty (90-day limited warranty on products that are

purchased as Refurbished*); whichever is longer.

*Refurbished products purchased from our online store

carry a 90-day replacement warranty.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident,

shipping or other physical damage, improper installation,

abnormal operation or handling, neglect, inundation, ﬁre,

water or other liquid intrusion; or

2. Product that has been damaged due to repair, alteration

or modiﬁcation by anyone other than an authorized

service representative of VTech; or

3. Product to the extent that the problem experienced is

caused by signal conditions, network reliability, or cable or

antenna systems; or

4. Product to the extent that the problem is caused by use

with non-VTech accessories; or

5. Product whose warranty/quality stickers, product serial

number plates or electronic serial numbers have been

removed, altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for repair

from outside the United States of America or Canada, or

used for commercial or institutional purposes (including

but not limited to Products used for rental purposes); or

7. Product returned without a valid proof of purchase (see

item 2 below); or

8. Charges for installation or set up, adjustment of customer

controls, and installation or repair of systems outside the

unit.

How do you get warranty service?

To obtain warranty service in the USA, please visit our

website at www.vtechphones.com or call 1 (800) 595-9511.

In Canada, go to www.vtechcanada.com or call

1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s

manual - a check of the Product’s controls and features may

save you a service call.

Except as provided by applicable law, you assume the risk

of loss or damage during transit and transportation and are

responsible for delivery or handling charges incurred in the

transport of the Product(s) to the service location. VTech

will return replaced Product under this limited warranty.

Transportation, delivery or handling charges are prepaid.

VTech assumes no risk for damage or loss of the Product in

transit.

What must you return with the Product to get warranty

service?

1. Return the entire original package and contents including

the Product to the VTech service location along with a

description of the malfunction or difﬁculty; and

2. Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model) and

the date of purchase or receipt; and

3. Provide your name, complete and correct mailing

address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement

between you and VTech. It supersedes all other written or

oral communications related to this Product. VTech provides

no other warranties for this Product. The warranty exclusively

describes all of VTech’s responsibilities regarding the Product.

There are no other express warranties. No one is authorized

to make modiﬁcations to this limited warranty and you should

not rely on any such modiﬁcation. State/Provincial Law Rights:

This warranty gives you speciﬁc legal rights, and you may also

have other rights, which vary from state to state or province

to province.

Limitations: Implied warranties, including those of ﬁtness

for a particular purpose and merchantability (an unwritten

warranty that the Product is ﬁt for ordinary use) are limited

to one year from the date of purchase. Some states/

provinces do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you.

In no event shall VTech be liable for any indirect, special,

incidental, consequential, or similar damages (including,

but not limited to lost proﬁts or revenue, inability to use

the Product or other associated equipment, the cost of

substitute equipment, and claims by third parties) resulting

from the use of this Product. Some states/provinces

do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or exclusion

may not apply to you.

Please retain your original sales receipt as proof

of purchase.

Limited warranty

The RBRC seal on the lithium-ion battery indicates that VTech Communications, Inc. is voluntarily participating in an

industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within

the United States and Canada. The program provides a convenient alternative to placing used lithium-ion batteries into

the trash or municipal waste, which may be illegal in your area.

VTech’s participation makes it easy for you to drop off the spent product at local retailers participating in the program

or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Li-ion battery recycling and disposal

bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and

conserving natural resources.

The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.

The RBRC seal

VTech RM7756 Guide de démarrage rapide

Marque: VTech

Modèle: RM7756

Catégorie: Moniteurs vidéo bébé

Taper: Guide de démarrage rapide

Télécharger le PDF

rapport

dans d''autres langues

English: VTech RM7756 Quick start guide

VTech RM7756 Guide de démarrage rapide

VTech RM7756 Guide de démarrage rapide

dans d''autres langues

Documents connexes