Modern Forms PD-61760 Kinetic Mode d'emploi

Modern Forms
Marque
Modern Forms
Modèle
PD-61760 Kinetic
Taper
Mode d'emploi
HARDWARE
WARNING
- Read all instructions before installing.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
INSTALLATION INSTRUCTION
1
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
G1 Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. July. 2022
Kinetic - LED Pendant
PD-61760
1WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
HARDWARE
WARNING
- Read all instructions before installing.
-
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
-
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
-
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
INSTALLATION INSTRUCTION
131 - LED Flush Mount
FM-13114
Wire Connector
Qty: 3 pcs + 1 Extra
Junction Box Screw
Qty: 2 pcs + 1 Extra
#8-32x1
Zinc Plating
Mounting Screw
Qty: 1 Extra
5/32-32x1/2
BN
Plastic Anchor
Qty: 3 pcs + 1 Extra
Wood Screw
Qty: 3 pcs + 1 Extra
Ø4x35
A1 B1 C1 D1 E1
PD-16818,PD-16824,PD-16830
168-LED Flush Mount
1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY, 2017
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
HARDWARE
WARNING
- Read all instructions before installing.
-
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
-
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
-
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
INSTALLATION INSTRUCTION
Slat - Vanities & Wall Sconces
WS-80618/WS-80624/WS-80636
Wire
Connector
Qty: 3 pcs
7EAC112201
Mounting
Ring
Qty: 1 pc
7MBC101501
Transformer
Qty: 1 pc
5EN-2460-R2
Junction
Box Screw
Qty: 2 pcs
+ 1 Extra
7MPF0825C1
8-32x1 SS
Conversion
Plate
Qty: 1 pc
4MBA151110BA
Mounting
Screw
Qty: 2 pcs
+ 1 Extra
7MPF0415C2
8-32x9/16 SS
Set
Screw
Qty: 2 Extra
7MPF0308S1
5/32-32x5/16
Nickel Plating
Mounting
Anchor
Qty: 2 pcs
7TDD082401
Tapping
Screw
Qty: 2 pcs
7MPF2204J2
Ø4x22
A1 B1 C1 D1 E1 F1 G1 H1 I1
Wire Connector
Qty: 3 pcs+1 Extra
Junction Box Screw
Qty: 2 pcs+1 Extra
#8-32x1
Zinc Plating
Mounting Screw
Qty: 1 Extra
5/32-32x1/2
BN
G0
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY, 2017
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
HARDWARE
WARNING
- Read all instructions before installing.
-
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
-
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
-
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
INSTALLATION INSTRUCTION
Slat - Vanities & Wall Sconces
WS-80618/WS-80624/WS-80636
Wire
Connector
Qty: 3 pcs
7EAC112201
Mounting
Ring
Qty: 1 pc
7MBC101501
Transformer
Qty: 1 pc
5EN-2460-R2
Junction
Box Screw
Qty: 2 pcs
+ 1 Extra
7MPF0825C1
8-32x1 SS
Conversion
Plate
Qty: 1 pc
4MBA151110BA
Mounting
Screw
Qty: 2 pcs
+ 1 Extra
7MPF0415C2
8-32x9/16 SS
Set
Screw
Qty: 2 Extra
7MPF0308S1
5/32-32x5/16
Nickel Plating
Mounting
Anchor
Qty: 2 pcs
7TDD082401
Tapping
Screw
Qty: 2 pcs
7MPF2204J2
Ø4x22
A1 B1 C1 D1 E1 F1 G1 H1 I1
PD-34865
348-LED Pendant
D
EF
QT
Y:1pcs
Nickl
e Plating
Tube_
A Setion Tube_B Setion Tube_C Setion
H I
Tube_D Setion
QTY:2pcs+1Extra
7TCH421301
Plastic Anchor
Wire Connector
Qty: 3pcs+1 Extra
Junction Bo
x Screw
Qty: 2pcs+
1 Extra
7EAC112201
P3
7MPF082
5F1
#8-32x
1
Nickle Pla
ting
AB
C
QTY:2pcs+1Extra
4EAL572501NI
Nickle Plating
Drop Hanger
G
QTY:2pcs+1Extra
4MBC251006NI
Nickle Plating
Decorative Ring
QTY:1pcs
Nickle Plating
QTY:1pcs
Nickle Plating
QTY:1pcs
Nickle Plating
617 - LED Pendant
PD-61760
Junction
Box Screw
Qty: 2pcs+1Extra
Wire
Connector
Qty:5pcs+1Extra
7EAC112201
P3
Allen Screw
Qty:1pc Extra
7MPF0303K1
1/8-40x 1/8
CE
D
Mounitng Screw
Qty:1pc Extra
4MPF041502PM/
4MPF041502BK
5/32-32x 9/16
G
Allen
Wrench
Qty: 1pc
7MPE155003
1/16x1/16x1 13/16
Black Zinc
F
Wood
Screw
Qty: 4pcs+1pc Extra
7MPF2204J2
Nickel
Ф4X22
B
Plastic Anchor
Qty: 4pcs+1pc Extra
7
TCH421301
Nickel
Ф4X22
A
Kinetic - LED Pendant
PD-61760
INSTALLATION INSTRUCTION
2
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
G1 Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. July. 2022
2WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTION
131 - LED Flush Mount
FM-13114
PREPARATION
1.
2.
CONNECTING THE WIRES (Fig. 2)
3.
4. Drill holes in the ceiling aligned with the key holes located in the mounting plate, insert the plastic anchors (D1).
5. Fig. 2, making sure that all wire connectors (A1) are secured.
back plate using the green screw provided.
After wires are connected, tuck them carefully inside the junction box.
MOUNTING THE FIXTURE (Fig. 1)
6. Secure the mounting plate to the junction box using junction box screws (B1),
fasten it to the wall using wood screw (E1). The side of the mounting back
plate marked “GND” must face out.
7.
8.
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
Plastic Anchor
Wire Connector
Wood Screw
Junction Box Screw
Mounting Screw
Fixture Shade
Mounting Plate
Junction Box
Glass
(RPL-GLA-13114)
Shade
(RPL-SHA-13114)
D1
A1
E1
B1
C1
FIG. 1
Ø
7"
Back Plate Dimensions
GND
Ø
8
3/4"
Ø
23/4"
Ø
31/2"
PD-16818,PD-16824,PD-16830
168-LED Flush Mount
1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY, 2017
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
8-32x1 SS 8-32x9/16 SS Nickel Plating
Junction Box
Mounting Plate
Canopy
Stem
Fixture
Shade
PC Diffuser
Glass
(RPL-GLA-13114)
(RPL-GLA-13120)
(RPL-GLA-13126)
Shade
(RPL-SHA-16818)
(RPL-SHA-16824)
(RPL-SHA-16830)
Diffuser
(RPL-DIF-13114)
(RPL-DIF-13120)
(RPL-DIF-13126)
PD-16818 4 3/4"
PD-16824 4 3/4"
PD-16830 4 3/4"
PD-16818 4 3/4"
PD-16824 4 3/4"
PD-16830 4 3/4"
PD-16818 2 -1/2"
PD-16824 2 -1/2"
PD-16830 2 -1/2"
G0
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JANUARY, 2017
Junction Box
Mounting Plate
Canopy
Stem
Fixture
Shade
PC Diffuser
Glass
(RPL-GLA-13114)
(RPL-GLA-13120)
(RPL-GLA-13126)
Shade
(RPL-SHA-16818)
(RPL-SHA-16824)
(RPL-SHA-16830)
Diffuser
(RPL-DIF-13114)
(RPL-DIF-13120)
(RPL-DIF-13126)
PD-16818 2-1/2"
PD-16824 2-1/2"
PD-16830 2-1/2"
PD-16818 4 3/4"
PD-16824 4 3/4"
PD-16830 4 3/4"
5. Choose number of rods suitable for your application.
7. Connect the canopy, rods and lamp body. Make sure all are tightened.
shown in Fig.2, making sure that all wire connectors (A) are secured. If your
mounting plate using the green screw provided. After wires are connected,
tuck them carefully inside the junction box.
4. Secure the mounting plate to the junction box using junction Box screws(B).The side of the mounting back plate marked “GND”
must face out.
MOUNTING THE FIXTURE (Fig. 1)
ary for installation.
PREPARATION
CONNECTING THE WIRES (Fig. 2)
COMPLETING THE INSTALLATION (Fig. 1, 2)
11. For slope ceiling application, rotate wire at the top of
the stem to ensure luminaries is aiming down.
Secure the mounting plate to the junction box using junction box screws (B1),
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare C
opper
(Ground)
Fig. 2 Wiring
PD-34865
348-LED Pendant
essary for installation.
PREPARATION
Fig.1 Fig.2
Fig.3 Fig.4
O
Allen Wrench
P
Allen
Screw
FDrop Hanger
GDecorative Ring
E
2 e
Plastic Anchor
N
Wire Clamp
K
Fixture
Fixture
Tube_B Setion
B
D
Tube_D Setion
LM
K
K
Tube_C Setion
C
Tube_A Setion
A
Transformer
2 3/8" " "
Transformer
2 3/8" "
Ground Wire
Junction Box
Mounting Plate
H
Wire C nect r
Transformer
2 3/8"
[L 2
"
[W] x
"
[ ]
J
M unting Screw
Fixture
I
Juncti n B x Screw
Cable Gripper
JK
Mounting Screw
QTY: 1 Extra
7MPF0412S1(NI)
#8-32x1/2
Nickle Plating
Lighting Section
QTY:5pcs
with two Connctors
Lighting Section
QTY:1pcs
with male Connctors
Lighting Section
QTY:1pcs
with female Connctors
LMNP
QTY:2pcs+1Extra
4MPE090602NI
Nickle Plating
Wire Clamp
Allen Screw
Qty: 4pcs+1 Extra
7MPF0303K1
1/8"-40×1/8
Nickel Plating
Allen Wrench
Qty: 1 Extra
7MPE155003
O
617 - LED Pendant
PD-61760
Back Plate Dimensions
7MBC382501
Fig.1
3. Remove the mounting screw (G) and Mounting
7. Drill holes in the wall aligned with the key hole located in
the mounting plate, insert the plastic anchor (A).
8. Secure mounting back plate to the junction box using
junction box screws (D), fasten it to the wall using wood
screw (B) The side of the mounting plate marked “GND”
must face out.
* Hook the two hooks on the mounting back plate slot.
Note: The fixture exceeds 100 lbs. and must be installed using an
outlet box U.L. approved for 200lbs.
9. Connect the driver input wires with outlet box wires, making
sure that all wire connectors (C) are secured. If your outlet box
directly to the mounting plate using the green screw provided.
After wires are connected, tuck them carefully inside the junction
box.
making sure that all wire connectors (C) are secured.
mounting screws (G).
12. The lamp ring can rotate 350 degree; rotate them to your desired
angles.
4. Remove two hoods from the safety cord; choose
the number of down rods suitable of your application.
the rods and canopy one by one. Connect the canopy,
rods and
6. Unscrew the Allen screw (F) using Allen wrench (E), pull
out the extra safety cord through clamp, leave a loop for
hooking, then secure the safety cords with clamp by
tightening the Allen screw, hook the hooks into the safety
cord loop.
CONNECTING THE WIRES (Fig. 2)
all the parts on a clear area. Be careful not to
lose any small parts necessary for installation.
PREPARATION
Rod
350°
350°
350°
350°
Mounting Screw
G
Canopy
Mounting Back Plate
Junction Box
D
F
E
Wire Connector
C
Driver
8-7/8" to 9-7/8"
x
3-9/16"
x
1-3/4"
Clamp
Plastic Anchor
A
B
Wood Screw
Cable(
Red/Black)
Hook
Pull
Safety Cords
U.L. Approved 200LB. Max.
Outlet Box and Hardware
( Sold Separately )
1 3/8”
15 1/4”
1 3/4”
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Fig. 2 Wiring
Fig. 3
(Ground)
Fig. 3
Turn to down
13
8"
13
4"
Back Plate Dimensions
DIMMING WIRING INFORMATION(FIG.4)
12. To utilize 0-10V dimming : use wire blue (dim+), white (dim-),brown(hot), blue (neutral),green&yollow (ground) and bare copper ground
wire (ground).
NOTE: Make sure to connect 0-10V prior to power-up the xture in order to allow the 0-10V dimming to function properly.
Kinetic - LED Pendant
PD-61760
INSTALLATION INSTRUCTION
FIG. 4 DRIVER WIRES
Input Output
Brown - Hot
Green & Yollow - Ground
Blue - Neutral
Center +
Bare -
Red +
Black -
Blue- Dim +
White - Dim -
3
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
G1 Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. July. 2022
  • Page 1 1
  • Page 2 2
  • Page 3 3

Modern Forms PD-61760 Kinetic Mode d'emploi

Modern Forms
Marque
Modern Forms
Modèle
PD-61760 Kinetic
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents