Modern Forms WS-54127 Cadence Mode d'emploi

Marque: Modern Forms

Modèle: WS-54127 Cadence

Taper: Mode d'emploi

INSTALLATION INSTRUCTIONS

541-Bath Light

WS-54127/WS-54139

HARDWARE

modernforms.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2020

Wire Connector

Qty:3+1Extra

Mounting Screw

Qty:2+1 Extra

Plastic Anchor

Qty:4+2Extra

Wood Screw

Qty: 4+2Extra

Square Plate

Qty:2pcs

Wire Connector

Qty:2+1Extra

Round Plate

Qty:2pcs

Mounting Bracket A

Qty:1pc

Mounting Bracket B

Qty:2pcs

Driver

Qty:1pc

ABCDE

FGHIJ



• Read all instructions before installing.

• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.

• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

• Retain installation instructions for future maintenance reference.

All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or

accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could

result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are

damaged or missing.

 Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal

areas clean all external surfaces of the xture once every two weeks with a wet cloth.

Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.

• Lisez toutes les instructions avant l’installation.

• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux

règlements locaux.

• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.

Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement

avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce

produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez

contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.

Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons

aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec

un chion humide.

INSTALLATION INSTRUCTIONS

541-Bath Light

WS-54127/WS-54139

FIG. 1

Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2020

modernforms.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

PREPARATION

MOUNTING WITH JUNCTION BOX (Fig. 1)

4. Choose between a square or round plate (F orG).

Note:

thread the driver's output wire through the hole of the plate.

9. I

Note

DIMMING WIRING INFORMATION (Fig. 4)

Square/Round Plate

Junction Box Screw

Mounting Screw

Mounting Hole

Junction Box

Cover

LED Tube

Driver

Cross Bar

Wire Connector

House Wire

Wire Connector

Driver Output Wire

Ground Wire

Plastic Anchor

Wood Screw

Mounting Bracket B

Mounting Screw

Mounting Bracket A

Standard

Driver Input Wire

>4”

Junction Box

Wall

12. This xture features electronic low voltage (ELV) or 0-10V dimming capabilities. See notes below for specic dimming wires information.

13. To utilize ELV dimming: use wires black (hot), white (neutral) and green ground wire (ground).

14. To utilize 0-10V dimming: use wire purple (dim+), pink or gray (dim-), black (hot), white (neutral) and green ground wire (ground).

滚滚长江东逝水

Purple - Dim+

Black - Hot

White - Neutral

Black - Output -

Red - Output +

INSTALLATION INSTRUCTIONS

541-Bath Light

WS-54127/WS-54139

FIG. 2

Fixture Wires

Black or

Fixture Wires

White or

Ribbed

Fixture Wires

Bare wire

(Ground)

House Wires

Black

(Hot)

House Wires

White

(Neutral)

House Wires

Green or Bare Copper

(Ground)

FIG. 3 Wiring

Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Nov. 2020

modernforms.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

Mounting Backplate Dimension

FIG.4 Driver Wiring

MOUNTING WITHOUT JUNCTION BOX (Fig. 2)

insert the plastic anchors (D).

3d1.28

Mounting Hole Dimensions

WS-54127 24

WS-54139 36

WS-54127 24

WS-54139 36

0.94

Access hole

Junction Box

0.45

Access hole Driver Output Wire

Standard

LED driver

Black - Hot

White - Neutral

Black - Output -

Red - Output +

Mounting hole

Plastic Anchor

Wood Screw

Wire Connector

Power feed

Mounting Screw

Cover

LED Tube

Mounting Bracket B

Mounting hole

Pink or Gray -Dim

Remote

LED

1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2023 G0

modernforms.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

INSTALLATION INSTRUCTION

Trimless Junction Box Cover

MKCP-3040-WT

OVERALL COMPONENT DIMENSIONS

CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER BEFORE

BEGINNING.

-Read all instructions before installing.

-System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.

-When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

-Retain installation instructions for future maintenance reference.

WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or

accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern Forms

could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are

damaged or missing.

MISE EN GARDE: POUR ÉVITER TOUT CHOC ÉLECTRIQUE, ASSUREZVOUS QUE LE DISJONCTEUR SOIT MIS HORS TENSION AVANT DE

COMMENCER.

-Lisez toutes les instructions avant l’installation.

-Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux règlements

locaux.

-Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.

ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement avec

les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus pour ce

produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez

contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.

COMPONENT OVERVIEW

The trimless junction box cover is intended for installation to NEC approved 4” square junction boxes recessed in drywall and ush with the

support structure. It may be covered with spackle and/or plaster to conceal junction box visibility. It is to be connected to compatible Modern

Forms xtures. Refer to specications sheets for more information.

TYP

HARDWARE

Wire Connector

Qty: 3 (+1 Extra)

½” Plastic Spacer

Qty: 2

⁄”-40 x 1⁄” Long

Mounting Screw

Qty: 2 (+1 Extra)

¾” Plastic Spacer

Qty: 2

#8-32 x ¾” Long

Junction Box Screw

Qty: 2 (+1 Extra)

1” Plastic Spacer

Qty: 2

NOTE: This accessory is supplied with an optional mounting C-ring for

xture connection via ⁄” K.O. hole. This component may be omitted

from the installation if mounting xtures using #8 screw holes.

2Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2023 G0

modernforms.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

INSTALLATION INSTRUCTION

Trimless Junction Box Cover

MKCP-3040-WT

FIG. 1

FIG. 2

FIG. 4

TRIMLESS JUNCTION BOX COVER INSTALLATION:

The trimless junction box cover is compatible with NEC approved

4” square junction boxes recessed in drywall and ush with the

support structure.

1. Install compatible junction box (by others) to the framing

structure. Ensure the junction box is ush with the base or front

of framing structure (See FIG. 1).

2. Install the mounting plate to the junction box (See FIG. 2).

Ensure the spacer alignment base is facing outward.

FIG. 3

105mm

FIG. 5 FIG. 6

3. Determine the drywall thickness and select the appropriate

spacer to install between the mounting plate and the trimless

junction box cover (See FIG. 3).

NOTE: Only 1 matching pair of spacers are to be used per

installation.

4. Using the mounting screws provided, attach the trimless

junction box cover to the mounting plate (See FIG. 4).

5. Make a 4⁄” square cutout in drywall at the intended trimless

junction box cover location and proceed to install to framing

structure (See FIG. 5). Apply and nish spackle up to the center

hole of trimless junction box cover. Ensure #8 holes on the

cover are free of spackle. (See FIG. 6).

Mounting Plate

Plastic

Spacers

Trimless Junction Box Cover

Cover Mounting Screws

Ground Wire

Example: ½” Drywall (No Spacer)

⁄”½”

Spacer Alignment

Base

Spacer

Height

Drywall

Thickness

No Spacer ½”

½” ⁄”

¾” 1”

1” 1¼”

Junction Box

Screws

3Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2023 G0

modernforms.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760