PowerStroke PS907000 Le manuel du propriétaire

Marque: PowerStroke

Modèle: PS907000

Catégorie: Groupes électrogènes

Taper: Le manuel du propriétaire

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

6,800 WATT GENERATOR

GÉNÉRATEUR DE 6 800 WATTS

GENERADOR 6 800 WATTS

PS907000

Series / Série / Serie

120V AC

CUSTOMER SERVICE (USA)

1-877-617-3501

SERVICE CLIENTELE (Canada)

1-877-617-3501

SERVICIO AL CLIENTE (Mexico)

01 800 843 1111

To register your POWERSTROKE product, please visit:

http://register.powerstroketools.com/

Pour enregistrer votre produit de POWERSTROKE, s’il

vous plaît la visite : http://register.powerstroketools.com/

Para registrar su producto de POWERSTROKE, por favor

visita: http://register.powerstroketools.com/

NEUTRAL BONDED TO FRAME

CONNECTEUR NEUTRE RELIÉ AU CADRE

PUNTO NEUTRO CONECTADO AL MARCO

SAVE THIS MANUAL FOR FUTURE REFERENCE

Your generator has been engineered and manufactured to our high standard for dependability, ease of operation, and operator

safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using this

product. If you do not understand the warnings and instructions in the operator’s manual, do not use this product.

Ce générateur a été conçu et fabriqué conformément à nos strictes

normes de fiabilité, simplicité d’emploi et sécurité d’utilisation.

Correctement entretenu, cet outil vous donnera des années de

fonctionnement robuste et sans problème.

AVERTISSEMENT :

Pour réduire les risques de blessures, l’utilisateur doit lire

et veiller à bien comprendre le manuel d’utilisation avant

d’employer ce produit. Si tous les avertissements et toutes les

consignes de sécurités et instructions du manuel d’utilisation

ne sont pas bien compris, ne pas utiliser ce produit.

Su generador diseñado y fabricado de conformidad con nuestras

estrictas normas para brindar fiabilidad, facilidad de uso y seguri-

dad para el operador. Con el debido cuidado, le brindará muchos

años de sólido funcionamiento y sin problemas.

ADVERTENCIA:

Para reducir el riesgo de lesiones, el usuario debe leer y

comprender el manual del operador antes de usar este

producto. Guarde este manual del operador y estúdielo

frecuentemente para lograr un funcionamiento seguro y

continuo de este producto.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

NOTICE AVIS AVISO

Do not use E15 or E85 fuel (or

fuel containing greater than 10%

ethanol) in this product. It is a

violation of federal law and will damage the unit and void

your warranty.

Ne pas utiliser d’essence E15 ou E85 (ou un carburant

contenant plus de 10 % d’éthanol) dans ce produit. Une

telle utilisation représente une violation de la loi fédérale et

endommagera l’appareil et annulera la garantie.

No utilice combustibles E15 o E85 (ni combustibles que

contengan más de 10 % de etanol) con este producto. Esto

constituye una violación a la ley federal, dañará la unidad

y anulará la garantía.

See this fold-out section for all of the figures

referenced in the operator’s manual.

Consulter l’encart à volets afin d’examiner toutes les figures

mentionnées dans le manuel d’utilisation.

Consulte esta sección desplegable para ver todas las figuras

a las que se hace referencia en el manual del operador.

Fig. 1

G - 240 volt AC 30 amp receptacle (prise 240 V

c.a. 30 A, 240 V de CA 30 A receptáculos)

H - 240 volt AC circuit breaker (disjoncteur de

c.a. 240 V, disyuntor de circuito de CA 240 V)

I - Cord retainers (retenue de cordon, retén

para el cordón)

J - Battery (pile, batería)

K - Engine switch with lock button (commutateur

du moteur avec bouton de verrouillage,

interruptor del motor con botón del seguro)

L - Oil cap/dipstick (bouchon/jauge d’huile,

tapa de relleno de aceite/varilla medidora de

aceite)

M- Oil drain plug (huiler le bouchon d’égout,

tapón de drenaje del aceite)

N - Battery maintainer charging cable (câble de

charge de mainteneur de batterie, cable de

carga del mantenedor de carga de la batería)

O - Engine battery charge circuit fuse (cuicuit de

fusible de charge pour la batterie du moteur,

fusible del circuito de carga de la batería del

motor)

P - Battery maintainer fuse (fusible de

mainteneur de batterie, fusible del

mantenedor de carga de la batería)

Q - Analog hour meter (compteur d’heures

analogique, horómetro analógico)

- Recoil starter grip (poignée du démarreur à

rappel, mango del arrancador retráctil)

S - Air filter (filtre à air, filtro de aire)

T - Handle lock pin (goupille de verrouillage de

poignée, pasador de seguro del mango)

U - Choke (d’étranglement, anegador)

A - Muffler (silencieux, silenciador)

B - Ground terminal (borne de terre, terminal de

conexión a tierra)

C - Fuel tank vapor vent (évent de vapeur du

réservoir de carburant, respirador del vapor

del tanque de combustible)

D - Fuel cap (bouchon de carburant, tapa del

tanque de combustible)

E - Fuel tank (réservoir de carburant, tanque de

combustible)

F - 120 volt AC 20 amp receptacles (prises 120

V c.a. 20 A, 120 V de CA 20 A receptáculos)

120V AC

LKJ

120V AC

iii

Fig. 2

Fig. 3

Fig. 4

A - Bolt (boulon, perno)

B - Frame (cadre, armazón)

C - Washer (rondelle, arandela)

D - Frame support with foot (support de cadre

avec pied, apoyo de bastidor con pie)

E - Flange nut (écrou à épaulement, tuerca de

brida)

F - Lock nut (écrou frein, tuerca de bloqueo)

G - Rubber foot (patin en caoutchouc, pie de

goma)

Fig. 5

A - Lock nut (écrou frein, tuerca de bloqueo)

B - U-bracket (support en U, soporte en “U”)

C - Wheel (roué, rueda)

D - Wheel spacer (écarteur de roué, espaciador

de rueda)

E - Washer (rondelle, arandela)

F - Bolt (boulon, perno)

A - Handle (poignée, mango)

B - Bolt (boulon, perno)

C - Spacer (separador, espaciador)

D - Washer (rondelle, arandela)

E - Lock nut (écrou frein, tuerca de bloqueo)

Fig. 6

DEF

aBaB

A - Socket wrench (clé à douille, llave de

casquillo)

B - Combination wrench (clé mixte, llave de

combinación)

C - Phillips screwdriver (tournevis cruciforme,

destornillador Phillips)

OFF

ENGINE

SWITCH

START

120V AC

Fig. 7

A - Lanyard (bracelet, correa)

B - Handle lock pin (goupille de blocage de la

poignée, pasador de seguro del mango)

C - Frame (cadre, armazón)

Fig. 8

A - Lanyard (bracelet, correa)

B - Hole (trou, agujero)

C - Handle (poignée, mango)

D - Handle lock pin (goupille de blocage de la

poignée, pasador de seguro del mango)

Fig. 10

Fig. 9

A - Oil cap/dipstick (bouchon/ jauge d’huile,

tapa de relleno de aceite/varilla medidora de

aceite)

B - Oil fill hole (orifice de remplissage d’huile,

agujero de llenado de aceite)

Fig. 11

A - Engine switch (contacteur du moteur,

interruptor del motor)

B - Fuel cap (bouchon de carburant, tapa del

tanque de combustible)

C - Fuel tank (réservoir de carburant, tanque de

combustible)

- Recoil starter grip (poignée du démarreur à

rappel, mango del arrancador retráctil)

Fig. 12

A - Fuel valve (robinet de carburant, válvula de

combustible)

B - Recoil starter grip (poignée de démarreur à

rappel, mango del arrancador retráctil)

Fig. 13

A - Push choke in to the open position (mettre le

d’étranglement en position ouvert, coloque

del anegador en la posición abierto)

B - Pull choke out to the closed position (tirez

le l’étrangleur en position fermé, tire del

anegador a la posición cerrado)

00000

OFF

START

ENGINE SW.

CIRCUIT PROTECTOR

ON OFF

120V AC/CA 120V AC/CA

120V/240 AC/CA

NEUTRAL FLOATING

NEUTRAL FLOTAS

Cor d

Retainer

Cor d

Retainer

A - Battery bracket (support de pile, soporte de

la batería)

B - Positive (+) terminal [borne positive (+), tapa

del terminal positiva (+)]

C - Negative (–) terminal [borne négative (–),

terminal negativa (–)]

D - Black wire (–) [fil noir (–), cable negro (–)]

E - Screw (vis, tornillo)

F - Washer (rondelle, arandela)

G - Nut (écrou, tuerca)

H - Red wire (+) [fil rouge (+), cable rojo (+)]

ECGF

OFF

OFF (aRRET,

aPaGaDO)

ON (MaRCHE,

ENCENDIDO)

A - Spark plug (bougie, bujía)

B - Spark plug cap (capuchon de bougie, tapa

de la bujía)

Fig. 17

A - Fuel line (conduite de carburant, conducto

de combustible)

B - Petcock (petit robinet, llave de purga)

C - Fuel valve (robinet de carburant válvula de

combustible)

D - Off (arret, apagado)

E - On (marche, encendido)

Fig. 19

Fig. 20

Fig. 14 aB

A - Carburetor drain screw (vis de vidange

du carburateur, tornillo de drenaje del

carburador)

Fig. 18

OFF

A - Fuel line (conduites de carburant, conducto

de combustible)

B - Fuel filter (filtre à carburant, filtro de

combustible)

Fig. 21

Fig. 16

A - Oil drain plug (huiler le bouchon d’égout,

tapón de drenaje del aceite)

B - Oil cap/dipstick (bouchon/ jauge d’huile,

tapa de relleno de aceite / varilla medidora

de aceite)

Fig. 15

A - Air filter cover (couvercle du filtre à air, tapa

del filtro de aire)

B - Filter element (élément du filter, elemento de

filtro)

C - Latches (loquets, broches)

D - Air filter unit (unité de filtre à air, unidad del

filtro de aire)

Fig. 23

A - Battery maintainer (mainteneur de charge

pour batterie, cargador mantenedor para

baterías)

B - Battery charging cable (câbles du charge de

pile, cable para cargar la batería)

C - Cover (couvercle, tapa)

D - Fuse (fusible, fusible)

120V AC

Fig. 22

OFF

A - Engine switch (contacteur du moteur,

interruptor del motor)

B - Off (arret, apagado)

C - Start (démarrage, arranque)

D - Lock button (bouton de verrouillage, botón

del seguro)

A - Fuse holder (porte-fusible, portafusibles)

B - Spring (ressort, resorte)

C - Fuse (fusible, fusible)

Page 2 — English

Introduction .................................................................................................................................................................... 2

Important Safety Instructions .....................................................................................................................................3-4

Specific Safety Rules ..................................................................................................................................................... 4

Symbols ......................................................................................................................................................................5-7

Electrical .....................................................................................................................................................................8-9

Features ...................................................................................................................................................................... 10

Assembly ................................................................................................................................................................11-13

Operation ................................................................................................................................................................13-15

Maintenance ...........................................................................................................................................................16-18

Troubleshooting ........................................................................................................................................................... 19

Warranty ..................................................................................................................................................................20-21

Parts Ordering / Service..................................................................................................................................Back Page

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product, making it easy to maintain and operate.

DANGER:

GROUNDING THE GENERATOR

To reduce the risk of shock or electrocution, generator must be properly grounded.

The nut and ground terminal on the frame must always be used to connect the genera-

tor to a suitable ground source. The ground path should be made with #8 size wire. Con-

nect the terminal of the ground wire between the lock washer and the nut, and tighten

the nut fully. Connect the other end of the wire securely to a suitable ground source.

The National Electric Code contains several practical ways in which to establish a good

ground source. If a steel or iron rod is used, it should be at least 5/8 in. diameter, and if a

nonferrous rod is used, it should be at least 1/2 in. diameter and be listed as material for

grounding. Drive the rod or pipe to a depth of 8 ft. If a rock bottom is encountered less than

4 ft. down, bury the rod or pipe in a trench.

All electrical tools and appliances operated from this generator must be properly grounded by use of

a third wire or be “Double Insulated.”

It is recommended to:

1. Use electrical devices with 3-prong grounded plugs.

2. Use an extension cord intended for outdoor use with a 3-pole receptacle and a 3-prong plug at opposite ends to

ensure continuity of the ground protection from the generator to the appliance.

Check and adhere to all applicable federal, state, and local regulations relating to grounding specifications. Consult a

qualified electrician or service personnel if the grounding instructions are not completely understood or if in doubt as

to whether the generator is properly grounded.

TABLE OF CONTENTS

INTRODUCTION

Page 3 — English

IMPORTANT SAFETY INSTRUCTIONS

DANGER:

Carbon Monoxide. Using a generator indoors CAN KILL

YOU IN MINUTES.

Generator exhaust contains high levels of carbon mon-

oxide (CO), a poisonous gas you cannot see or smell. If

you can smell the generator exhaust, you are breathing

CO. But even if you cannot smell the exhaust, you could

be breathing CO.

Never use a generator inside homes, garages, crawl-

spaces, or other partly enclosed areas. Deadly levels

of carbon monoxide can build up in these areas. Us-

ing a fan or opening windows and doors does NOT

supply enough fresh air.

ONLY use a generator outdoors and far away from

open windows, doors, and vents. These openings

can pull in generator exhaust.

Even when you use a generator correctly, CO may

leak into the home. ALWAYS use a battery-powered or

battery-backup CO alarm in the home.

If you start to feel sick, dizzy, or weak after the generator

has been running, move to fresh air RIGHT AWAY. See

a doctor. You could have carbon monoxide poisoning.

WARNING:

Read and understand all instructions. Failure to follow

all instructions listed below could result in electrocution,

fire, and/or carbon monoxide poisoning, which can cause

death or serious injury.

DANGER:

National Electric Code requires generator to be grounded

to an approved earth ground. Before using the ground ter-

minal, consult a qualified electrician, electrical inspector,

or local agency having jurisdiction for local codes or or-

dinances that apply to the intended use of the generator.

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be

followed during installation and maintenance of the genera-

tor and batteries.

Do not connect to a building’s electrical system unless

the generator and transfer switch have been properly

installed and the electrical output has been verified by

a qualified electrician. The connection must isolate the

generator power from utility power and must comply with

all applicable laws and electrical codes.

Do not allow children or untrained individuals to use this

unit.

Do not start or operate the engine in a confined space,

building, near open windows, or in other unventilated space

where dangerous carbon monoxide fumes can collect.

Carbon monoxide, a colorless, odorless, and extremely

dangerous gas, can cause unconsciousness or death.

Keep all bystanders, children, and pets at least 10 feet

away.

Wear sturdy and dry shoes or boots. Do not operate while

barefoot.

Do not operate generator when you are tired or under the

influence of drugs, alcohol, or medication.

Keep all parts of your body away from any moving parts

and all hot surfaces of the unit.

Do not touch bare wire or receptacles.

Do not use generator with electrical cords which are worn,

frayed, bare, or otherwise damaged.

Before storing, allow the engine to cool and drain fuel

from the unit.

Do not operate or store the generator in rain, snow, or

wet weather.

Store the generator in a well-ventilated area with the fuel

tank empty. Fuel should not be stored near the generator.

Empty fuel tank, close fuel valve, and restrain the unit

from moving before transporting in a vehicle.

Allow engine to cool for five minutes before refueling.

To reduce the risk of fire and burn injury, handle fuel with

care. It is highly flammable.

Do not smoke while handling fuel.

Store fuel in a container approved for gasoline.

Position the unit on level ground, stop engine, and allow

to cool before refueling.

Loosen fuel cap slowly to release pressure and to keep

fuel from escaping around the cap.

Tighten the fuel cap securely after refueling.

Wipe spilled fuel from the unit.

Never attempt to burn off spilled fuel under any circum-

stances.

Generators vibrate in normal use. During and after the

use of the generator, inspect the generator as well as

extension cords and power supply cords connected to

it for damage resulting from vibration. Have damaged

items repaired or replaced as necessary. Do not use plugs

or cords that show signs of damage such as broken or

cracked insulation or damaged blades.

For power outages, permanently installed stationary gen-

erators are better suited for providing back-up power to

the home. Even a properly connected portable generator

can become overloaded. This may result in overheating

or stressing the generator components, possibly leading

to generator failure.

Page 4 — English

IMPORTANT SAFETY INSTRUCTIONS

SPECIFIC SAFETY RULES

Use only authorized replacement parts and accessories

and follow instructions in the Maintenance section of this

manual. Use of unauthorized parts or failure to follow

maintenance instructions may create a risk of shock or

injury.

Maintain the unit per maintenance instructions in this

Operator’s Manual.

Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace damaged parts.

WARNING:

When this generator is used to supply a building

wiring system: generator must be installed by a quali-

fied electrician and connected to a transfer switch as

a separately derived system in accordance with NFPA

70, National Electrical Code. The generator shall be

connected through a transfer switch that switches all

conductors other than the equipment grounding con-

ductor. The frame of the generator shall be connected to

an approved grounding electrode. Failure to isolate the

generator from power utility can result in death or injury

to electric utility workers.

Do not use this generator to provide power for emergency

medical equipment or life support devices.

This generator has a neutral bonded condition. This

means the neutral conductor is electrically connected to

the frame of the machine.



Exhaust contains poisonous carbon monoxide, a colorless,

odorless gas. Breathing exhaust can cause loss of con-

sciousness and can lead to death. If running in a confined

or partially-enclosed area, the air may contain a danger-

ous amount of carbon monoxide. To keep exhaust fumes

from building up, always provide adequate ventilation.



Always use a battery-powered carbon monoxide detec-

tor when running the generator. If you begin to feel sick,

dizzy, or weak while using the generator, shut it off and

get to fresh air immediately. See a doctor. You may have

carbon monoxide poisoning.



Place the generator on a flat, stable surface with a slope

of no more than 4°.



Operate in a well-ventilated, well-lit area isolated from

working areas to avoid noise interference.



Operating the generator in wet conditions could result in

electrocution. Keep the unit dry.



Keep the generator a minimum of 3 feet away from all

types of combustible material.



Do not operate generator near hazardous material.



Do not operate generator at a gas or natural gas filling

station.



Do not touch the muffler or cylinder during or immediately

after use; they are HOT and will cause burn injury.

Do not allow the generator’s gas tank to overflow when

filling. Fill to 1 in. below the top neck of the gasoline tank

to allow for fuel expansion. Do not cover the fuel tank cap

when the engine is running. Covering the fuel tank cap

during use may cause engine failure and/or damage to

the tool.



Do not smoke when filling the generator with gasoline.



Shut down the engine and allow to cool completely before

adding gasoline or lubricant to the generator.



Do not remove the oil dipstick or the fuel tank cap when

the engine is running.



Pay close attention to all safety labels located on the

generator.



Keep children a minimum of 10 feet away from the gen-

erator at all times.



The unit operates best in temperatures between 23°F and

104°F with a relative humidity of 90% or less.



Operating voltage and frequency requirement of all

electronic equipment should be checked prior to plug-

ging them into this generator. Damage may result if the

equipment is not designed to operate within a +/- 10%

voltage variation, and +/- 3 hz frequency variation from

the generator name plate ratings. To avoid damage, al-

ways have an additional load plugged into the generator

if solid state equipment (such as a television set) is used.

A power line conditioner is recommended for some solid

state applications.

 When battery pack is not in use, keep it away from other

metal objects like paper clips, coins, keys, nails, screws,

or other small metal objects that can make a connection

from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

For outdoor use only.



Save these instructions. Refer to them frequently and use

them to instruct others who may use this product. If you loan

someone this product, loan them these instructions also.

Page 5 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Wet Conditions Alert Do not expose to rain or use in damp locations.

Electric Shock Failure to use in dry conditions and to observe safe practices can

result in electric shock.

Toxic Fumes

Running generator gives off carbon monoxide, an odorless, color-

less, poison gas. Breathing carbon monoxide can cause nausea,

fainting, or death.

Fire/Explosion Fuel and its vapors are extremely flammable and explosive. Fire

or explosion can cause severe burns or death.

Hot Surface To reduce the risk of injury or damage, avoid contact with any hot

surface.

Lifting Hazard To reduce the risk of serious injury, avoid attempting to lift the

generator alone.

Ground Consult with local electrician to determine grounding requirements

before operation.

Electrocution Failure to properly ground generator can result in electrocution,

especially if the generator is equipped with a wheel kit.

Recycle Symbol

This product uses lead acid (Pb) batteries. Local, state or federal

laws may prohibit disposal of batteries in ordinary trash. Consult

your local waste authority for information regarding available re-

cycling and/or disposal options.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

NOTICE: (Without Safety Alert Symbol) Indicates important information not related to an

injury hazard, such as a situation that may result in property damage.

Page 6 — English

You WILL be KILLED or SERIOUSLY HURT if you do not

follow the Operator’s Manual instructions.

Risk of Fire. Do not add fuel while the product is operat-

ing.

Generator is a potential source of electric shock. Do not

expose to moisture, rain, or snow. Do not operate with

wet hands or feet.

Exhaust contains poisonous carbon monoxide gas that

can cause unconsciousness or DEATH. Operate in well-

ventilated, outdoor areas away from open windows or

doors.

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

hrs Hours Time

gal Gallon Volume

qt Quart Volume

SAFETY LABELS

The information below can be found on the generator. For

your safety, please study and understand all of the labels

before starting the generator.

If any of the labels come off the unit or become hard to read,

contact an authorized service center for replacement.

Failure to properly ground generator can result in elec-

trocution, especially if the generator is equipped with a

wheel kit.

Do not expose to rain or use in damp locations.

Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide. This is a

poison you cannot see or smell.

NEVER use inside a home or garage, EVEN IF doors and

windows are open.

Only use OUTSIDE and far away from windows, doors,

and vents.

Page 7 — English

WARNING

ADVERTENCIA

AVERTISSEMENT

HOT SURFACE

SURFACES TRÉS CHAUDE

SUPERFICIES CALIENTE

FUEL WARNING

No smoking when filling with gasoline.

Do not overfill. Full level is 1 in. below the

top of the fuel neck. Stop the engine for

five minutes before refueling to avoid the

heat from the muffler igniting fuel vapors.

ENGINE LUBRICANT WARNING

You must add lubricant before first op-

erating the generator. Always check the

lubricant level before each operation. The

lubricant level should always register be-

tween the hatched areas on the dipstick. The unit is equipped with a sensor which

will automatically shut off the engine if the lubricant level falls below a safe limit.

GROUNDING WARNING

National Electric Code requires generator to be grounded to an approved earth

ground.

HOT SURFACE WARNING

Do not touch the muffler or aluminum

cylinder of the engine. They are very HOT

and will cause severe burns. Don’t put

any flammable or combustible materials

in the direct path of the exhaust.

SYMBOLS

CLEARANCE WARNING

While operating and storing, keep at

least 3 feet of clearance on all sides

of this product, including overhead.

Allow a minimum of 30 minutes of

“cool down” time before storage. Heat

created by muffler and exhaust gases

could be hot enough to cause serious

burns and/or ignite combustible objects.

SPARK ARRESTOR

Operation of this equipment may create sparks that can start

fires around dry vegetation. A spark arrestor may be required.

The operator should contact local fire agencies for laws or

regulations relating to fire prevention requirements.

Page 8 — English

EXTENSION CORD CABLE SIZE

Refer to the table below to ensure the cable size of the extension cords you use are capable of carrying the required load.

Inadequate size cables can cause a voltage drop, which can burn out the appliance and overheat the cord.

Current in

Amperes

Load in Watts Maximum Allowable Cord Length

At 120V At 240V #8 Wire #10 Wire #12 Wire #14 Wire #16 Wire

2.5 300 600 1000 ft. 600 ft. 375 ft. 250 ft.

5 600 1200 500 ft. 300 ft. 200 ft. 125 ft.

7.5 900 1800 350 ft. 200 ft. 125 ft. 100 ft.

10 1200 2400 250 ft. 150 ft. 100 ft. 50 ft.

15 1800 3600 150 ft. 100 ft. 65 ft.

20 2400 4800 175 ft. 125 ft. 75 ft.

25 3000 6000 150 ft. 100 ft.

30 3600 7200 125 ft. 65 ft.

40 4800 9600 90 ft.

ELECTRIC MOTOR LOADS

It is characteristic of common electric motors in normal operation to draw up to six times their running current while starting.

This table may be used to estimate the watts required to start electric motors; however, if an electric motor fails to start or

reach running speed, turn off the appliance or tool immediately to avoid equipment damage. Always check the requirements

of the tool or appliance being used compared to the rated output of the generator.

Motor Size (H.P.) Running Watts Watts Required to Start Motor

Universal Capacitor Split Phase

1/8 275 N/A 850 1200

1/6 275 600 850 2050

1/4 400 800 1050 2400

1/3 450 950 1350 2700

1/2 600 1000 1800 3600

3/4 850 1200 2600 —

1 1100 N/A 3300 —

NOTICE:

Operating voltage and frequency requirement of all electronic equipment should be checked prior to plugging them into

this generator. Damage may result if the equipment is not designed to operate within a +/- 10% voltage variation, and

+/- 3 hz frequency variation from the generator name plate ratings. To avoid damage, always have an additional load

plugged into the generator if solid state equipment (such as a television set) is used. A power line conditioner is recom-

mended for some solid state applications.

ELECTRICAL

Page 9 — English

GENERATOR CAPACITY

Make sure the generator can supply enough continuous (run-

ning) and surge (starting) watts for the items you will power

at the same time. Follow these simple steps.

1. Selecttheitemsyouwillpoweratthesametime.

2. Totalthecontinuous(running)wattsoftheseitems.This

is the amount of power the generator must produce to

keep the items running. See the wattage reference chart

at right.

3. Estimatehowmanysurge(starting)wattsyouwillneed.

Surge wattage is the short burst of power needed to start

electric motor-driven tools or appliances such as a circular

saw or refrigerator. Because not all motors start at the

same time, total surge watts can be estimated by adding

only the item(s) with the highest additional surge watts to

the total rated watts from step 2.

NOTICE:

Do not overload the generator’s capacity. Exceeding the

generator’s wattage/amperage capacity may damage

the generator and/or electrical devices connected to it.

ELECTRICAL

POWER MANAGEMENT

To prolong the life of the generator and attached devices,

it is important to take care when adding electrical loads to

the generator. There should be nothing connected to the

generator outlets before starting its engine. The correct and

safe way to manage generator power is to sequentially add

loads as follows:

1. With nothing connected to the generator, start the engine

as described later in this manual.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

Never add more loads than the generator capacity. Take

special care to consider surge loads in generator capacity

as previously described.

Application/Equipment Estimated

Run Watts

Estimated

Starting

Watts

Emergency / Home Standby

Clock Radio 50 50

Lights (qty. 4 x 75 W) 300 300

Refrigerator 700 2200

Furnace Fan 800 2350

Water Well Pump 1000 1500

Microwave 1000 1000

Sump Pump 1050 2200

Electric Range (per element) 2100 2100

Job Site

ElectricDrill−1/2HP 600 900

AirlessSprayer−1/3HP 600 1200

Quartz Halogen Work Light 1000 1000

Reciprocating Saw 960 1920

AirCompressor−1HP 1600 4500

CircularSaw−7-1/4in. 1400 2300

Planer/Jointer−6in 1800 1800

MiterSaw−10in. 1800 1800

TableSaw/RadialArmSaw−10in. 2000 2000

*Wattages listed are approximate. Check tool or appliance for actual wattage.

Example:

Tool or Appliance Running

Watts*

Additional

Starting Watts*

Window AC,

10,000 BTU 1200 1800

Refrigerator 700 2200

1/3 HP Well Pump 1000 2000

27 in. Television 500 0

Light (75 Watts) 75 0

3475 Total

Running Watts

2200 Highest

Starting Watts

Total Running Watts 3475

Highest Starting Watts + 2200

Total Starting Watts Required 5675

Page 10 — English

KNOW YOUR GENERATOR

See Figure 1.

The safe use of this product requires an understanding of the

information on the product and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

AC CIRCUIT BREAKERS

The circuit breakers are provided to protect the generator

against electrical overload.

AIR FILTER

The air filter helps to limit the amount of dirt and dust drawn

into the unit during operation.

ANALOG HOUR METER

The analog hour meter operates whenever the engine is

running and keeps track of how many hours the unit has

been used.

BATTERY CHARGING FUSES

The engine battery charge circuit fuse and the battery main-

tainer fuse protect the battery.

BATTERY MAINTAINER

Using the battery maintainer when storing the generator helps

keep your generator’s battery charged and ready at all times.

CHOKE

The choke is used when starting a cold engine.

CORD RETAINERS

Use the cord retainers to prevent plugs from being

accidentally pulled out of the receptacles.

ENGINE SWITCH

The engine switch is used either alone or in combination

with the recoil starter grip to start the generator.

FUEL TANK

The fuel tank has a capacity of 8 gallons.

FUEL VALVE

Fuel flow from the fuel tank to the engine is turned on and

off using the fuel valve.

GROUND TERMINAL

The ground terminal is used to assist in properly ground-

ing the generator to help protect against electrical shock.

Consult with a local electrician for grounding requirements

in your area.

LOW OIL SHUT DOWN PROTECTOR

The low oil sensor causes the engine to stop if the level of

oil in the crankcase is insufficient.

OIL CAP/DIPSTICK

Remove the oil fill cap to check and add lubricant to the

generator when necessary.

OIL DRAIN PLUG

When changing the engine lubricant, unscrew and remove the

oil drainage bolt to allow old engine lubricant to be drained.

RECEPTACLES

Your generator has the following single phase, 60 Hz outlets:

four 120 Volt AC, 20 Amp receptacles, and one 240 Volt AC,

30 Amp receptacle. These can be used for operating appro-

priate appliances, electrical lighting, tools, and motor loads.

RECOIL STARTER GRIP

The recoil starter grip is used (along with the engine switch)

to start the generator’s engine.

FEATURES

PRODUCT SPECIFICATIONS

ENGINE

Engine Type .........................................GX390, 389cc, OHV

Fuel Volume ................................................................ 8 gal.

GENERATOR

Rated Voltage .....................................................120V/240V

Rated Amps ..................................................... 56.7A/28.3A

Rated Output ........................................................... 6800 W

Starting Watts .......................................................... 8500 W

Rated Frequency ........................................................60 Hz

DIMENSIONS

Length ........................................................................ 31 in.

Width ....................................................................... 20.6 in.

Height ...................................................................... 23.8 in.

Weight ................................................................. 209.4 lbs.

Page 11 — English

UNPACKING

This product requires assembly.

 Carefully cut the box down the sides then remove the

machine and any accessories from the box. Make sure

that all items listed in the loose parts list are included.

NOTE: This machine is heavy and requires a minimum of

two people to lift. To avoid back injury, lift with your legs

and not your back.

WARNING:

Do not use this product if any parts on the Loose Parts

List are already assembled to your product when you

unpack it. Parts on this list are not assembled to the

product by the manufacturer and require customer instal-

lation. Use of a product that may have been improperly

assembled could result in serious personal injury.

 Inspect the unit carefully to make sure no damage oc-

curred during shipping.

 Do not discard the packing material until you have carefully

inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-877-617-3501 for assistance.

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

WARNING:

Do not attempt to operate the generator until assembly

is complete. Failure to comply could result in possible

serious personal injury.

LOOSE PARTS LIST

See Figure 2

The following items are included with the generator:

Key

No. Description Qty.

1 Bolt (3/8-16 x 4-1/4 in.) ................................... 2

2 Washer (3/8 in.) ................................................ 2

3 Spacer (.38 ID) ................................................. 2

4 Wheel ............................................................... 2

5 Lock Nut (3/8-16) ............................................. 2

6 Handle Lock Pin .............................................. 2

7 Lanyard ............................................................ 2

8 Lock Nut (1/4-20) ............................................. 2

9 Washer (1/4 in.) ................................................ 2

10 Rubber Foot .................................................... 2

11 Bolt (1/4-20 x 1-1/2 in.) ................................... 2

12 Flange Nut (5/16-18) ........................................ 2

13 Washer (5/16 in.) .............................................. 6

14 Bolt (5/16-18 x 1 in.) ........................................ 2

15 Frame Support ................................................ 1

16 Engine Lubricant.............................................. 1

17 Bolt (5/16-18 x 2-1/4 in.) ................................. 2

18 Lock Nut (5/16) ................................................ 2

19 Handle ............................................................. 2

20 Handle Bracket Spacers.................................. 2

21 Battery Maintainer ........................................... 1

Operator’s Manual (not shown) ....................... 1

TOOLS NEEDED

See Figure 3.

The following tools (not included or drawn to scale) are

needed for assembly:

8 mm, 11 mm, 13 mm, and 14 mm Socket Wrenches and/

or Combination Wrenches

Phillips Screwdriver

NOTE: Do not put fuel or lubricant in the generator before

installing the feet, frame support, and wheels.

INSTALLING FEET ON THE FRAME SUPPORT

See Figure 4.

Locate the following items:

2 rubber feet

2 lock nuts (1/4-20)

2 washers (1/4 in.)

2 bolts (1/4-20 x 1-1/2 in.)

Insert bolt through foot, then through frame support as

shown.

Thread washer over the bolt, then install lock nut. Tighten

nut securely.

NOTE: Be careful not to overtighten so that foot material

collapses.

Repeat with remaining foot.

ASSEMBLY

Page 12 — English

INSTALLING THE FRAME SUPPORT

See Figure 4.

Install the frame support on the bottom of the generator

frame on the same side as the handle.

Locate the following items:

Frame support

2 flange nuts (5/16-18)

2 washers (5/16 in.)

2 bolts (5/16-18 x 1 in.)

Raise the end of the generator where the recoil starter is

located high enough to gain access to the frame bottom;

securely position props underneath to support.

Align the holes on the frame support with the holes on

the generator frame.

Insert the bolt through the hole in the generator frame so

it extends down through the frame support.

Slide a washer on the bolt, then install flange nut and

tighten securely.

Repeat on other side.

INSTALLING THE WHEELS

See Figure 5.

Wheels are provided to assist in moving the generator to

the desired location and should be installed on the side

opposite the handle.

Locate the following items:

2 bolts (3/8-16 x 5-1/4 in.)

2 washers (3/8 in.)

2 spacers (.38 ID)

2 wheels

2 lock nuts (3/8-16)

Raise the end of the generator opposite the handle

high

enough to gain access to the frame bottom; securely

position props underneath to support.



Insert a wheel spacer into the center of the wheel.



Place a washer on the bolt, then slide bolt through the

wheel.



Slide the bolt through the U-bracket frame on generator.



nstall nut and tighten securely.

Repeat the process on the other side to install second

wheel.

ATTACHING THE HANDLE

See Figure 6.

Locate the following items:

2 handles

2 bolt (5/16-8 x 3/4 in.)

4 washers (5/16)

2 lock nuts (5/16)

2 handle bracket spacers

Place handle and spacer on the frame.

Place a washer on a bolt, then slide bolt through the

handle, the frame and the spacer.

Slide a washer on the bolt, then install nut and tighten

securely.

Repeat the process on the other side to install second

handle.

LOCKING THE HANDLE

See Figures 7 - 8.

Locate the following items:

2 handle lock pins

2 lanyards

Attach the lanyard to the handle lock pin and the handle

as shown in figure 7.

Extend the handle, then insert the pin through the hole

in the handle and the generator frame to secure handle

in place.

Repeat the process on the other side to lock the other

handle.

CAUTION:

Do not attempt to lift the unit by the handle assembly. If

it is necessary to lift the generator, always grasp by the

frame. Use proper lifting techniques to avoid back injury.

RELEASING THE HANDLES

Remove the handle lock pins and lower the handles to

the down position.

WARNING:

To reduce the risk of electrocution or explosion, do not

short circuit the battery terminals or charge in a sealed

container. Keep sparks and flame away.

WARNING:

Keep metal objects away from the battery terminals.

Metal objects can make a connection from one terminal

to another. Shorting the battery terminals together may

cause sparks, burns, or a fire.

ASSEMBLY

Page 13 — English

ASSEMBLY

CONNECTING/DISCONNECTING BATTERY

See Figure 9.

The battery cables must be connected before the electric

start feature of the generator can be operated.

To connect battery cables:

Connect the red wire to the positive (+) terminal first, then

connect the black wire to the negative (–) terminal. Make

sure all connections are tight.

NOTE: Be careful not to short across the terminals when

installing. Shorting the terminals together can cause

sparks, damage to the battery or generator, or even burns

or explosions.

Cover the terminals with the rubber covers.

When removing the battery for replacement: disconnect

the negative (black) post, then the positive (red) post, being

careful not to short across the terminals. Always abide by the

safety warnings provided with the battery. Remove the bat-

tery and dispose of according to local and state regulations.

OPERATION

DANGER:

Carbon Monoxide. Using a generator indoors CAN KILL

YOU IN MINUTES.

Generator exhaust contains high levels of carbon mon-

oxide (CO), a poisonous gas you cannot see or smell. If

you can smell the generator exhaust, you are breathing

CO. But even if you cannot smell the exhaust, you could

be breathing CO.

Never use a generator inside homes, garages, crawl-

spaces, or other partly enclosed areas. Deadly levels

of carbon monoxide can build up in these areas. Us-

ing a fan or opening windows and doors does NOT

supply enough fresh air.

ONLY use a generator outdoors and far away from

open windows, doors, and vents. These openings

can pull in generator exhaust.

Even when you use a generator correctly, CO may

leak into the home. ALWAYS use a battery-powered or

battery-backup CO alarm in the home.

If you start to feel sick, dizzy, or weak after the generator

has been running, move to fresh air RIGHT AWAY. See

a doctor. You could have carbon monoxide poisoning.

DANGER:

Failure to properly ground generator can result in elec-

trocution, especially if the generator is equipped with a

wheel kit. National Electric Code requires generator to be

properly grounded to an approved earth ground. Call an

electrician for local grounding requirements.

WARNING:

Do not allow familiarity with this product to make you

careless. Remember that a careless fraction of a second

is sufficient to inflict serious injury.

WARNING:

Do not use any attachments or accessories not recom-

mended by the manufacturer of this product. The use of

attachments or accessories not recommended can result

in serious personal injury.

APPLICATIONS

This generator is designed to supply electrical power for

operating compatible electrical lighting, appliances, tools,

and motor loads.

BEFORE OPERATING THE UNIT

Only use OUTSIDE and far away from windows, doors,

and vents.

NEVER use inside a home or garage, EVEN IF doors and

windows are open.

Always position the generator on a flat firm surface.

SPECIAL REQUIREMENTS:

There may be General or State Occupational Safety and

Health Administration (OSHA) regulations, local codes or

ordinances that apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or

the local agency having jurisdiction:

In some areas, generators are required to be registered

with local utility companies.

If the generator is used at a construction site, there may

be additional regulations which must be observed.

Page 14 — English

CHECKING/ADDING LUBRICANT

See Figure 10.

NOTICE:

Attempting to start the engine before it has been properly

filled with lubricant will result in equipment failure.

Engine lubricant has a major influence on engine perfor-

mance and service life. For general, all-temperature use,

SAE 10W-30 is recommended. Always use a 4-stroke motor

lubricant that meets or exceeds the requirements for API

service classification SJ.

NOTE: Non-detergent or 2-stroke engine lubricants will

damage the engine and should not be used.

Unscrew the oil cap/dipstick and remove.

Wipe dipstick clean and re-seat in hole; do not re-thread.

Remove dipstick again and check lubricant level. Lubri-

cant level should fall between the hatched areas on the

dipstick.

If level is low, add engine lubricant until the fluid level rises

to the upper portion of the dipstick.

Replace and secure the oil cap/dipstick.

USING FUEL STABILIZER

Fuel gets old, oxidizes, and breaks down over time. Adding

a fuel stabilizer (not included) extends the usable life of fuel

and helps prevent deposits from forming that can clog the

fuel system. Follow fuel stabilizer manufacturer’s directions

for correct ratio of stabilizer to fuel.

Mix fuel stabilizer and gasoline prior to filling the tank

by using a gas can or other approved fuel container and

shaking gently to combine.

NOTE: To control the amount of fuel stabilizer being added

to the engine, always mix fuel stabilizer with gasoline

before fueling the tank rather than adding fuel stabilizer

directly into the generator’s fuel tank.

Replace and secure the fuel tank cap.

Start and run the engine for at least 5 minutes to allow

stabilizer to treat the entire fuel system.

OXYGENATED FUELS

NOTICE:

Do not use E15 or E85 fuel (or fuel containing greater

than 10% ethanol) in this product. It is a violation of

federal law and will damage the unit and void your

warranty.

Fuel system damage or performance problems resulting

from the use of an oxygenated fuel containing more than

the percentage of oxygenates stated below are not covered

under warranty.

Ethanol. Gasoline containing up to 10% ethanol by volume

(commonly referred to as E10) is acceptable. E15 and E85

are not.

CHECKING/ADDING FUEL

See Figure 11.

WARNING:

Gasoline and its vapors are highly flammable and ex-

plosive. To prevent serious personal injury and property

damage, handle gasoline with care. Keep away from igni-

tion sources, handle outdoors only, do not smoke while

adding fuel, and wipe up spills immediately.

When adding gas to the generator, make sure the unit is

sitting on a flat, level surface. If the engine is hot, let the

generator cool before adding gas. ALWAYS fill the fuel tank

outdoors with the machine turned off.

Remove the fuel cap.

Fill the fuel tank to 1 in. below the top of the fuel neck.

Replace and secure the fuel cap.

NOTE: Always use unleaded gasoline with a pump octane

rating of 86 or higher. Never use old, stale, or contaminated

gasoline, and do not use an oil/gas mixture. Do not allow dirt

or water into the fuel tank. Do not use E85 fuel.

ELECTRIC START

This generator model is provided with both electric start and

recoil start capabilities. Avoid prolonged cranking, as it can

damage the engine.

The battery provided is a nominal 12 volt sealed recharge-

able lead-acid battery and can be operated in any position

without leakage. It complies with non-spillable battery

regulations. Its convenient size offers a 30% reduction over

conventional batteries.

NOTE: Brand new generators are shipped with the battery

connections disconnected. The positive and negative ter-

minals must be connected to the battery before the Electric

Start feature will work.

For initial battery connection, see Connecting/Disconnect-

ing Battery.

OPERATION

Page 15 — English

STARTING THE ENGINE

See Figures 11 - 14.

NOTICE:

On a level surface with the engine off, check the lubricant

level before each use of the generator.

NOTE: If location of generator is not level, the unit may not

start or may shut down during operation.

Unplug all loads from the generator.

Turn the fuel valve to the ON position.

Pull the choke out to the START position.

NOTE: If engine is warm or the temperature is above

50˚F,pushthechokeintotheRUN position.

Put the engine switch in the ON ( I ) position.

 Slide down and hold the lock button while pushing the

engine switch to the START position.

NOTE: The battery may require charging before the gen-

erator can be started using only the engine switch. The

generator can be started by pulling the recoil starter grip.

Once the generator is started, the battery will charge as

the unit runs.

The generator can also be started by pulling the recoil

starter grip until the engine runs (a maximum of 6 times).

NOTE: Do not allow the grip to snap back after starting;

return it gently to its original place.

Allow the engine to run for 15-30 seconds, then move

the choke to the RUN position.

STOPPING THE ENGINE

See Figures 11 - 13.

To stop the engine under normal operating conditions:

Remove any load from the generator and allow the engine

to stabilize.

Turn the fuel valve to the OFF position.

Put the engine switch in the OFF ( O ) position.

To stop the engine in an emergency situation:

Put the engine switch in the OFF ( O ) position.

WARNING:

While operating and storing, keep at least 3 feet of clear-

ance on all sides of this product, including overhead.

Allow a minimum of 30 minutes of “cool down” time

before storage. Heat created by muffler and exhaust

gases could be hot enough to cause serious burns and/

or ignite combustible objects.

HIGH ALTITUDE OPERATION

Specific modifications are needed for high-altitude operation.

Please contact your authorized service center for important

information regarding these modifications. Operating this

engine without the proper altitude modification may increase

the engine’s emissions and decrease fuel economy and

performance.

OPERATION

Page 16 — English

WARNING:

When servicing, use only identical replacement parts. Use

of any other parts could create a hazard or cause product

damage.

Only the parts shown on the parts list are intended to be repaired

or replaced by the customer. All other parts should be replaced

at an authorized service center.

GENERAL MAINTENANCE

Keep the generator in a clean and dry environment where it is

not exposed to dust, dirt, moisture, or corrosive vapors. Do not

allow the cooling air slots in the generator to become clogged

with foreign material such as leaves, etc.

Do not use a garden hose to clean the generator. Water enter-

ing the fuel system or other internal parts of the unit can cause

problems that will decrease the life of the generator.

To clean the unit:

Use a soft bristle brush and/or vacuum cleaner to loosen

and remove dirt and debris.

Clean air vents with low pressure air that does not exceed

25 psi.

Wipe the exterior surfaces of the generator with a damp

cloth.

CHECKING/CLEANING AIR FILTER

See Figure 15.

For proper performance and long life, keep air filter clean.

Release latches on side of air filter cover. Remove cover and

set aside.

Remove the filter element.

If the filter element is dirty, clean with warm, soapy water.

Rinse and let dry.

Apply a light coat of engine lubricant to the element, then

squeeze it out.

Replace the element in the air filter unit.

Replace the air filter cover and latch to secure.

NOTE: Do not run the generator without the air filter. Rapid

engine wear will result.

CHANGING ENGINE LUBRICANT

See Figure 16.

Remove the oil cap/dipstick.

Place a container underneath the oil drain plug to collect

used lubricant as it drains.

Unscrew the oil drain plug and remove.

Allow lubricant to drain completely.

NOTE: Drain the lubricant while the engine is still warm but

not hot. Warm lubricant will drain quickly and more com-

pletely.

WARNING:

Do not change engine lubricant while it is hot. Accidental

contact with hot engine lubricant could result in serious burns.

Reinstall the oil drain plug and tighten securely.

Refill with lubricant following the instructions in the Checking/

Adding Lubricant section. For amount of lubricant needed

to refill, see Product Specifications earlier in this manual

or the accompanying engine manual, if applicable.

Reinstall the oil cap/dipstick.

NOTE: Used lubricant should be disposed of at an approved

disposal site. See your local oil retailer for more information.

SPARK PLUG MAINTENANCE

See Figure 17.

The spark plug must be properly gapped and free of deposits

in order to ensure proper engine operation. To check:

Remove the spark plug cap.

Clean any dirt from around base of spark plug.

Remove spark plug using wrench (not included).

Inspect spark plug for damage, and clean with a wire brush

(not included) before reinstalling. If insulator is cracked or

chipped, spark plug should be replaced. For replacement

spark plug, see Product Specifications earlier in this manual

or the accompanying engine manual, if applicable.

Measure plug gap. The correct gap is 0.028−0.031 in.

(0.7-0.8 mm). To widen gap, if necessary, carefully bend the

ground (top) electrode. To lessen gap, gently tap ground

electrode on a hard surface.

Seat spark plug in position; thread in by hand to prevent

cross-threading.

Tighten with wrench to compress washer. If spark plug is

new, use 1/2 turn to compress washer appropriate amount. If

reusing old spark plug, use 1/8 to 1/4 turn for proper washer

compression.

NOTE: An improperly tightened spark plug will become very

hot and could damage the engine.

SPARK ARRESTOR

See Figure 18.

Inspect the spark arrestor for breaks or holes. Re-

place if necessary. To purchase a replacement spark

arrestor contact Powerstroke customer service at

1-877-617-3501.

Use a brush (not provided) to remove carbon deposits from

the spark arrestor screen as needed.

DRAINING FUEL TANK/CARBURETOR

See Figures 19 - 20.

To help prevent gum deposits in the fuel system, drain the fuel

from the tank and carburetor before storing.

DRAINING THE FUEL TANK

Turn the engine switch OFF ( O ).

Turn the fuel valve to the OFF position.

Remove the fuel line from the petcock by squeezing the ends

of the retaining clip and sliding the fuel line off.

Install one end of a drain line over the petcock, and place

the other end in a fuel container large enough to catch the

fuel being drained from the tank.

Turn the fuel valve to the ON position.

MAINTENANCE

La page charge ...

PowerStroke PS907000 Le manuel du propriétaire

Marque: PowerStroke

Modèle: PS907000

Catégorie: Groupes électrogènes

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: PowerStroke PS907000 Owner's manual
español: PowerStroke PS907000 El manual del propietario

PowerStroke PS907000 Le manuel du propriétaire

PowerStroke PS907000 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents