Toro TimeCutter MX 4275T 107 cm Zero Turn Riding Mower 74691 Manuel utilisateur

Form No. 3465-221 Rev A

T imeCutter

®

MR4275T or MR5075T Zero T urn Riding

Mower

74691 , 74695

T imeCutter

®

MR4275T oder MR5075T Nullwendekreis-

Aufsitzrasenmäher

74691 , 74695

T ondeuse autoportée à rayon de braquage zéro

T imeCutter

®

MR4275T ou MR5075T

74691 , 74695

T imeCutter

®

MR4275T en MR5075T zero-turn zitmaaier

74691 , 74695

www .T oro.com.

*3465-221*

Form No. 3465-205 Rev A

T imeCutter

®

MR4275T or

MR5075T Zero T urn Riding

Mower

Model No. 74691 —Serial No. 414500000 and Up

Model No. 74695 —Serial No. 414500000 and Up

Register at www .T oro.com.

Original Instructions (EN)

*3465-205*

This product complies with all relevant European

directives; for details, please see the separate product

specic Declaration of Conformity (DOC) sheet.

Gross or Net T orque: The gross or net torque

of this engine was laboratory rated by the engine

manufacturer in accordance with the Society of

Automotive Engineers (SAE) J1940 or J2723. As

congured to meet safety , emission, and operating

requirements, the actual engine torque on this class

of mower will be signicantly lower . Please refer to

the engine manufacturer ’ s information included with

the machine.

The enclosed engine owner's manual is supplied

for information regarding the US Environmental

Protection Agency (EP A) and the California Emission

Control Regulation of emission systems, maintenance,

and warranty . Replacements may be ordered through

the engine manufacturer .

Introduction

This rotary-blade, riding lawn mower is intended to be

used by homeowners in residential applications. It is

designed primarily for cutting grass on well-maintained

lawns. Using this product for purposes other than

its intended use could prove dangerous to you and

bystanders.

Read this information carefully to learn how to operate

and maintain your product properly and to avoid

injury and product damage. Y ou are responsible for

operating the product properly and safely .

V isit www .T oro.com for product safety and operation

training materials, accessory information, help nding

a dealer , or to register your product.

Whenever you need service, genuine T oro parts, or

additional information, contact an Authorized Service

Dealer or T oro Customer Service and have the model

and serial numbers of your product ready . Figure 1

identies the location of the model and serial numbers

on the product. W rite the numbers in the space

provided.

Important: W ith your mobile device, you can

scan the QR code on the serial number decal (if

equipped) to access warranty , parts, and other

product information.

g297763

Figure 1

Under the seat

1. Model and serial number location

W rite the product model and serial numbers in the

space below:

Model No.

Serial No.

This manual uses 2 words to highlight information.

Important calls attention to special mechanical

information and Note emphasizes general information

worthy of special attention.

The safety-alert symbol ( Figure 2 ) appears both in

this manual and on the machine to identify important

safety messages that you must follow to avoid

accidents. This symbol will appear with the word

Danger ,W arning , or Caution .

•Danger indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury .

•W arning indicates a potentially hazardous

situation which, if not avoided, could result in

death or serious injury .

•Caution indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderate injury .

sa-black

Figure 2

1. Safety-alert symbol

81 1 1 L yndale A venue South

Bloomington, MN 55420

2

Contact us at www .T oro.com.

Printed in the USA

Contents

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

General Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Slope Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Safety and Instructional Decals . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1

Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Attachments/Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Before Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Before Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Performing Daily Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Breaking in a New Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Using the Safety-Interlock System . . . . . . . . . . . . . . . . . . . . 14

Positioning the Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Adjusting the MyRide® Suspension

System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Adjusting the Motion-Control Levers . . . . . . . . . . . . . . . . . 15

Converting to Side Discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

During Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

During Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Operating the Mower Blade-Control Switch

(PT O) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Operating the Throttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Operating the Choke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Starting the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Shutting Of f the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Using the Motion-Control Levers . . . . . . . . . . . . . . . . . . . . . . . 22

Driving the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Using the Smart Speed

T M

Control

System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Using the Side Discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Adjusting the Height of Cut . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Adjusting the Anti-Scalp Rollers . . . . . . . . . . . . . . . . . . . . . . . . 25

Operating T ips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

After Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

After Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Cleaning the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Pushing the Machine by Hand . . . . . . . . . . . . . . . . . . . . . . . . . . 27

T ransporting the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Maintenance Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Recommended Maintenance Schedule(s) . . . . . . . . . . . 31

Pre-Maintenance Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Releasing the Mower-Deck Curtain . . . . . . . . . . . . . . . . . . 32

Raising the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Greasing the Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Engine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Engine Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Servicing the Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Servicing the Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Servicing the Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Cleaning the Blower Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Fuel System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Replacing the In-Line Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . 38

Electrical System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Electrical System Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Servicing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Servicing the Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Drive System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Checking the T ire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Releasing the Electric Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Adjusting the T racking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Belt Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Inspecting the Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Replacing the Mower Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Mower Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Blade Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Servicing the Cutting Blades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Leveling the Mower Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Removing the Mower Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Installing the Mower Deck . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Replacing the Grass Deector . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

W ashing the Underside of the Mower

Deck .............................................................. 51

Disposing of W aste . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Storage Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Storing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

T roubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

3

Safety

This machine has been designed in accordance with

EN ISO 5395.

General Safety

This product is capable of amputating hands and

feet and of throwing objects. Always follow all safety

instructions to avoid serious personal injury or death.

•Read and understand the contents of this

Operator ’ s Manual before starting the engine.

•Keep bystanders and children away .

•Do not allow children or untrained people to

operate or service the machine. Allow only people

who are responsible, trained, familiar with the

instructions, and physically capable to operate or

service the machine.

•Do not operate the machine near drop-of fs,

ditches, embankments, water , or other hazards, or

on slopes greater than 15°.

•Do not put your hands or feet near moving

components of the machine.

•Do not operate the machine without all guards,

safety switches, and other safety protective

devices in place and functioning properly .

•Shut of f the engine, remove the key , and wait

for all moving parts to stop before leaving the

operator ’ s position. Allow the machine to cool

before servicing, adjusting, fueling, cleaning, or

storing it.

4

Slope Indicator

g01 1841

Figure 3

Y ou may copy this page for personal use.

1. The maximum slope you can operate the machine on is 15 degrees . Use the slope chart to determine the degree of slope of

hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line

to match the recommended slope.

2. Align this edge with a vertical surface, a tree, building, fence pole, etc.

3. Example of how to compare slope with folded edge

5

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger . Replace any decal that is damaged or missing.

decalbatterysymbols

Battery Symbols

Some or all of these symbols are on your battery .

1. Explosion hazard 6. Keep bystanders away

from the battery .

2. No re, open ame, or

smoking

7. W ear eye protection;

explosive gases can

cause blindness and other

injuries.

3. Caustic liquid/chemical

burn hazard

8. Battery acid can cause

blindness or severe burns.

4. W ear eye protection. 9. Flush eyes immediately

with water and get medical

help fast.

5. Read the Operator's

Manual .

10. Contains lead; do not

discard

decaloemmarkt

Manufacturer's Mark

1. This mark indicates that the blade is identied as a part

from the original machine manufacturer .

Decal 99-3943 is for models with 127 cm (50 inch)

decks only .

decal99-3943

99-3943

1. Belt routing

2. Engine

Decal 105-7015 is for models with 107 cm (42 inch)

decks only .

decal105-7015

105-7015

1. Belt routing

6

Decal 1 12-9840 is for models with 127 cm (50 inch)

decks only .

decal1 12-9840

1 12-9840

1. Read the Operator's

Manual .

3. Remove the ignition key

and read the instructions

before servicing or

performing maintenance.

2. Height of cut

decal121-2989b

121-2989

1. Bypass lever position for

pushing the machine

2. Bypass lever position for

operating the machine

decal130-0731

130-0731

1. W arning—thrown object

hazard; keep the deector

shield in place.

2. Cutting hazard of hand or

foot, mower blade—keep

away from moving parts.

decal132-0872

132-0872

1. Thrown object

hazard—keep bystanders

away from the machine.

3. Severing hazard of hand

or foot—keep away from

moving parts.

2. Thrown object hazard,

raised deector—do not

operate the machine with

an open deck; use a

bagger or a deector .

4. Entanglement

hazard—keep away

from moving parts; keep

all guards and shields in

place.

Decal 138-6074 is molded into the fuel tank.

decal138-2456

138-6074

1. Read the Operator ’ s

Manual .

3. Do not overll the fuel

tank.

2. Park the machine on a

level surface when lling

the fuel tank.

7

decal139-2388

139-2388

1. Slow

3. Fast

2. Hauling

Decal 139-2391 is for models without an hour meter .

decal139-2391

139-2391

1. Fast

2. Slow

decal139-2394

139-2394

1. T raction controls 4. Neutral

2. Fast 5. Reverse

3. Slow

6. Parking brake

decal139-2395

139-2395

1. Parking brake 4. Neutral

2. Fast 5. Reverse

3. Slow

6. T raction controls

decal139-2397

139-2397

decal140-2748

140-2748

decal142-5864

142-5864

8

decal132-0869

132-0869

Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum

recommended slope indicated on the decal. Review the instructions for operating the machine on slopes in the Operator ’ s Manual as

well as the conditions in which you would operate the machine to determine whether you can operate the machine in the conditions on

that day and at that site. Changes in the terrain can result in a change in slope operation for the machine.

1. W arning—read the

Operator's Manual .

3. Cutting/dismemberment

hazard of the hand, mower

blade; entanglement

hazard of the hand,

belt—stay away from

moving parts; keep all

guards and shields in place.

5. T ipping hazard—do not

use dual ramps when

loading onto a trailer; use

1 ramp wide enough for

the machine; use a ramp

with a slope less than 15°;

back up the ramp when

loading the machine and

drive forward of f the ramp

when unloading.

7. T ipping hazard—do not use

the machine near drop-of fs

or on slopes greater than

15°; only operate across

slopes less than 15°.

2. W arning—read the

Operator's Manual before

performing maintenance;

engage the parking brake,

remove the key , and

disconnect the spark plug.

4. Thrown object

hazard—keep bystanders

away; pick up debris

before operating; keep the

deector in place.

6. Runover hazard—do not

carry passengers; look

behind you when mowing

in reverse.

9

Product Overview

g367815

Figure 4

1. Engine 4. Motion-control levers

7. Smart Speed ™lever

10. Rear drive wheel

2. Operator seat

5. Front caster wheel

8. Height-of-cut lever 1 1. Control panel

3. Fuel-tank cap

6. Deck-lift pedal (certain

models only)

9. Deector

12. MyRide ™adjustment lever

10

Controls

Become familiar with all the controls before you start

the engine and operate the machine.

Control Panel

g293303

Figure 5

1. Throttle control 3. Blade-control switch

(power takeof f)

2. Choke control

4. Key switch

Key Switch

The key switch, used to start and shut of f the engine,

has 3 positions: O FF , R UN , and S TART (Figure 5 ).

Throttle Control

The throttle controls the engine speed, and it has a

continuous-variable setting from the S LOW to F AST

position ( Figure 5 ).

Choke Control

Use the choke control to start a cold engine ( Figure 5 ).

Blade-Control Switch (Power

T akeoff)

The blade-control switch, represented by a

power-takeof f (PT O) symbol, engages and

disengages power to the mower blades ( Figure 5 ).

Motion-Control Levers

Use the motion-control levers to drive the machine

forward, reverse, and turn either direction ( Figure 4 ).

Park Position

Move the motion-control levers outward from the

center to the P ARK position when exiting the machine

to engage the electric brake ( Figure 24 ). Always

position the motion-control levers into the P ARK

position when you stop the machine or leave it

unattended.

MyRide® Adjustment Lever

Use the MyRide® adjustment lever to adjust the seat

suspension ( Figure 4 ).

Smart Speed ™Control System

Lever

The Smart Speed ™Control-System lever , located

below the operating position, gives you a choice to

drive the machine at 3 speed ranges— trim, tow , and

mow ( Figure 27 ).

Fuel-Presence W indow

Y ou can use the fuel window , located on the left side

of the machine, to verify the presence of fuel in the

tank ( Figure 6 ).

g292100

Figure 6

1. Fuel-presence window

1 1

Height-of-Cut Lever

Use the height-of-cut lever to lower and raise the deck

from the seated position. Moving the lever up (toward

you) raises the deck from the ground and moving the

lever down (away from you) lowers the deck toward

the ground. Adjust the height-of-cut only while the

machine is not moving ( Figure 28 ).

Foot Pedal Deck-Lift System

Certain Models Only

The foot pedal deck-lift system allows you to lower and

raise the deck from the seated position. Y ou can use

the foot pedal to lift the deck briey to avoid obstacles

or assist in adjusting the height of cut ( Figure 4 ).

Specications

Specications and design are subject to change

without notice.

42in Mower Deck 50in Mower Deck

Cutting width 107 cm (42 inches) 127 cm (50 inches)

Width with

deector down

135 cm (53 inches) 155 cm (61 inches)

Width with

deector raised

123 cm (48.5

inches)

130 cm (51 inches)

Length

185 cm (73 inches) 186 cm (73 inches)

Height

1 12 cm (44 inches) 109 cm (43 inches)

W eight

332 kg (731 lb) 353 kg (779 lb)

Attachments/Accessories

A selection of T oro approved attachments and

accessories is available for use with the machine

to enhance and expand its capabilities. Contact

your Authorized Service Dealer or authorized T oro

distributor or go to www .T oro.com for a list of all

approved attachments and accessories.

T o ensure optimum performance and continued safety

certication of the machine, use only genuine T oro

replacement parts and accessories. Replacement

parts and accessories made by other manufacturers

could be dangerous, and such use could void the

product warranty .

Operation

Note: Determine the left and right sides of the

machine from the normal operating position.

Before Operation

Before Operation Safety

General Safety

•Do not allow children or untrained people to

operate or service the machine. Local regulations

may restrict the age of the operator . The owner

is responsible for training all operators and

mechanics.

•Inspect the area where you will use the machine,

and remove all objects that could interfere with

the operation of the machine or that the machine

could throw .

•Become familiar with the safe operation of the

equipment, operator controls, and safety signs.

•Check that operator-presence controls, safety

switches, and guards are attached and working

properly . Do not operate the machine unless they

are functioning properly .

•Shut of f the engine, remove the key , and wait

for all moving parts to stop before leaving the

operator ’ s position. Allow the machine to cool

before servicing, adjusting, fueling, cleaning, or

storing it.

•Before mowing, inspect the machine to ensure

that the cutting assemblies are working properly .

•Evaluate the terrain to determine the appropriate

equipment and any attachments or accessories

required to operate the machine properly and

safely .

•W ear appropriate clothing, including eye

protection; long pants; substantial, slip-resistant

footwear; and hearing protection. T ie back long

hair and do not wear loose clothing or loose

jewelry .

•Do not carry passengers on the machine.

•Keep bystanders and pets away from the machine

during operation. Shut of f the machine and

attachment(s) if anyone enters the area.

•Do not operate the machine unless all guards and

safety devices, such as the deectors and the

entire grass catcher , are in place and functioning

properly . Replace worn or deteriorated parts when

necessary .

12

Fuel Safety

•Fuel is extremely ammable and highly explosive.

A re or explosion from fuel can burn you and

others and can damage property .

– T o prevent a static charge from igniting the

fuel, remove the machine from the truck or

trailer and refuel it on the ground, away from

all vehicles. If this is not possible, place a

portable fuel container on the ground, away

from all vehicles, and ll it; then refuel the

machine from the fuel container rather than

from a fuel-dispenser nozzle.

– Fill the fuel tank outdoors on level ground, in

an open area, and when the engine is cold.

Wipe up any fuel that spills.

– Do not handle fuel when smoking or around an

open ame or sparks.

– Do not remove the fuel cap or add fuel to the

tank while the engine is running or hot.

– If you spill fuel, do not attempt to start the

engine. A void creating a source of ignition until

the fuel vapors have dissipated.

– Store fuel in an approved container and keep

it out of the reach of children.

•Fuel is harmful or fatal if swallowed. Long-term

exposure to vapors can cause serious injury and

illness.

– A void prolonged breathing of vapors.

– Keep your hands and face away from the

nozzle and the fuel-tank opening.

– Keep fuel away from your eyes and skin.

•Do not store the machine or fuel container where

there is an open ame, spark, or pilot light, such

as on a water heater or on other appliances.

•Do not operate the machine without the entire

exhaust system in place and in proper working

condition.

•Keep the fuel-dispenser nozzle in contact with

the rim of the fuel tank or container opening at

all times until fueling is complete. Do not use a

nozzle lock-open device.

•If you spill fuel on your clothing, change your

clothing immediately .

•Do not overll the fuel tank. Replace the fuel cap

and tighten it securely .

•Clean grass and debris from the cutting unit,

muf er , drives, grass catcher , and engine

compartment to help prevent res. Clean up oil or

fuel spills.

Adding Fuel

Recommended Fuel

T ype Unleaded gasoline

Minimum octane rating

87 (US) or 91 (research

octane; outside the US)

Ethanol

No more than 10% by volume

Methanol None

MTBE (methyl tertiary butyl

ether)

Less than 15% by volume

Oil Do not add to the fuel

Use only clean, fresh (no more than 30 days old), fuel

from a reputable source.

Using Stabilizer/Conditioner

Use fuel stabilizer/conditioner in the machine to keep

the fuel fresh longer when used as directed by the

fuel-stabilizer manufacturer .

Important: Do not use fuel additives containing

methanol or ethanol.

Add the amount of fuel stabilizer/conditioner to fresh

fuel as directed by the fuel-stabilizer manufacturer .

Filling the Fuel T ank

1. Park the machine on a level surface.

2. Move the motion-control levers outward to the

PARK position.

3. Shut of f the engine and remove the key .

4. Clean around the fuel-tank cap.

5. Fill the fuel tank to the bottom of the ller neck

(Figure 7 ). Do not ll the fuel tank completely

full.

13

g293796

Figure 7

Performing Daily

Maintenance

Before starting the machine each day , perform the

Each Use/Daily procedures listed in Maintenance

( page 30 ) .

Breaking in a New Machine

New engines take time to develop full power . Mower

decks and drive systems have higher friction when

new , placing additional load on the engine. Allow

40 to 50 hours of break-in time for new machines to

develop full power and best performance.

Using the Safety-Interlock

System

W ARNING

If the safety-interlock switches are

disconnected or damaged, the machine could

operate unexpectedly , causing personal

injury .

• Do not tamper with the interlock switches.

• Check the operation of the interlock

switches daily and replace any damaged

switches before operating the machine.

Understanding the

Safety-Interlock System

The safety-interlock system is designed to prevent the

engine from starting unless:

•The blade-control switch (PT O) is disengaged.

•The motion-control levers are in the P ARK position.

The safety-interlock system also is designed to shut

of f the engine whenever the control levers are out of

the P ARK position and you rise from the seat.

T esting the Safety-Interlock

System

T est the safety-interlock system before you use the

machine each time. If the safety system does not

operate as described below , have an Authorized

Service Dealer repair the safety system immediately .

1. Sit on the seat, move the motion-control levers

in the P ARK position, and move the blade-control

switch to the O Nposition. T ry starting the

engine; the engine should not crank.

2. Sit on the seat and move the blade-control switch

to the O FF position. Move either motion-control

lever to the center , unlocked position. T ry

starting the engine; the engine should not crank.

Repeat with the other motion-control lever .

3. Sit on the seat, move the blade-control switch

to the O FF position, and lock the motion-control

levers in the P ARK position. Start the engine.

While the engine is running, engage the

blade-control switch, and rise slightly from the

seat; the engine should shut of f.

4. Sit on the seat, move the blade-control switch

to the O FF position, and lock the motion-control

levers in the P ARK position. Start the engine.

While the engine is running, move the

motion-control levers to the center , unlocked

position and rise slightly from the seat; the

engine should shut of f.

14

Positioning the Seat

The seat can move forward and backward. Position

the seat where you have the best control of the

machine and are most comfortable ( Figure 8 ).

g027632

Figure 8

Adjusting the MyRide®

Suspension System

Y ou can adjust the MyRide® suspension system for a

smooth and comfortable ride. The slots for adjusting

the suspension have detent positions for reference,

ranging from a soft to a rm ride ( Figure 9 ).

1. Park the machine on a level surface, disengage

the blade-control switch, and move the

motion-control levers outward to the P ARK

position.

2. Shut of f the engine, remove the key , and wait

for all moving parts to stop before leaving the

operating position.

3. Step of f the machine.

4. While standing on the right side of the machine,

move the adjustment lever left toward the –

symbol for a softer suspension.

Move the adjustment lever right toward the +

symbol for a rmer suspension.

g292102

Figure 9

1. MyRide adjustment lever 3. Firmer suspension

2. Softer suspension

Adjusting the

Motion-Control Levers

Adjusting the Height

Y ou can adjust the motion-control levers higher or

lower for maximum comfort ( Figure 10 ).

g333847

Figure 10

15

Adjusting the T ilt

Y ou can adjust the motion-control levers forward or

rearward for your comfort.

1. Loosen the upper bolt holding the control lever

to the control-arm shaft.

2. Loosen the lower bolt just enough to pivot the

control lever forward or rearward.

g333846

Figure 1 1

3. T ighten both bolts to secure the control lever in

the new position.

4. Repeat the adjustment for the other control lever .

Converting to Side

Discharge

The mower deck and mower blades shipped with the

machine were designed for optimum mulching and

side-discharge performance.

Install the fasteners from the loose parts bag into the

empty holes after removing the recyling baf es.. This

ensures that no holes are left open when operating

the mower deck.

W ARNING

Open holes in the machine expose you and

others to thrown debris that can cause severe

injury .

• Never operate the machine without

hardware mounted in all holes in the

machine housing.

• Install the hardware in the mounting holes

when you remove the mulching bafe.

Machines with 107 cm (42-inch)

Mower Decks

1. Park the machine on a level surface, disengage

the blade-control switch, and move the

motion-control levers outward to the P ARK

position.

2. Shut of f the engine, remove the key , and wait

for all moving parts to stop before leaving the

operating position.

3. Remove the mower deck; refer to Removing the

Mower Deck ( page 49 ) .

4. Remove the 2 locknuts (5/16 inch) from the

welded posts of the baf e ( Figure 12 ).

g296990

Figure 12

1. Locknut—5/16 inch (4) 3. Baf e

2. Carriage bolt—5/16 x 3/4

inch (2)

4. W elded post (2)

5. Remove the 2 carriage bolts and 2 locknuts

securing the baf e to the deck and remove the

baf e ( Figure 12 )

6. Locate the 2 bolts in loose parts and use the

existing locknuts to install these fasteners into

the holes used for the welded posts ( Figure 12 )

to prevent ying debris.

Note: Install the bolt upward, through the

underside of the deck and use an existing

locknut to secure from the topside.

7. Install the mower deck; refer to Installing the

Mower Deck ( page 50 ) .

16

Machines with 127 cm (50-inch)

Mower Decks

1. Park the machine on a level surface, disengage

the blade-control switch, and move the

motion-control levers outward to the P ARK

position.

2. Shut of f the engine, remove the key , and wait

for all moving parts to stop before leaving the

operating position.

3. Remove the mower deck; refer to Removing the

Mower Deck ( page 49 ) .

4. Remove the 3 locknuts (5/16 inch) from the

welded posts of the right baf e ( Figure 13 ).

g297022

Figure 13

1. Locknut—5/16 inch (4) 3. Carriage bolt—5/16 x 3/4

inch

2. Right baf e 4. W elded post (3)

5. Remove the 2 carriage bolts and 2 locknuts

securing the right baf e to the deck and remove

the baf e ( Figure 13 ).

6. Locate the 3 bolts in loose parts and use the

existing locknuts and install these fasteners into

the holes used for the welded posts ( Figure 13 )

to prevent ying debris.

Note: Install the bolt upward, through the

underside of the deck and use an existing

locknut to secure from the topside.

7. Remove the 2 locknuts (5/16 inch) from the

welded posts of the left baf e ( Figure 14 ).

g297021

Figure 14

1. Locknut—5/16 inch (3) 3. W elded post (2)

2. Left baf e 4. Carriage bolt—5/16 x 3/4

inch

8. Remove the carriage bolt and locknut securing

the left baf e to the deck and remove the baf e

(Figure 14 ).

9. Locate the 2 bolts in loose parts and use the

existing locknuts and install these fasteners into

the holes shown in Figure 14 on the mower deck

to prevent ying debris.

Note: Install the bolt upward, through the

underside of the deck and use an existing

locknut to secure from the topside.

10. Remove the nut from the grass deector rod

under the mower deck ( Figure 15 ).

17

g297046

Figure 15

1. Grass deector

3. Nut

2. Grass deector rod 4. Cutof f baf e

1 1. Use the nut to install the cutof f baf e to the grass

deector rod, using the outer hole in the baf e

(Figure 15 ).

12. Install the mower deck; refer to Installing the

Mower Deck ( page 50 ) .

During Operation

During Operation Safety

General Safety

•The owner/operator can prevent and is responsible

for accidents that may cause personal injury or

property damage.

•Use your full attention while operating the

machine. Do not engage in any activity that

causes distractions; otherwise, injury or property

damage may occur .

•Do not operate the machine while ill, tired, or

under the inuence of alcohol or drugs.

•Contacting the blade can result in serious personal

injury . Shut of f the engine, remove the key , and

wait for all moving parts to stop before leaving the

operating position. When you turn the key to the

OFF position, the engine should shut of f and the

blade should stop. If not, stop using your machine

immediately and contact an Authorized Service

Dealer .

•Operate the machine only in good visibility and

appropriate weather conditions. Do not operate

the machine when there is the risk of lightning.

•Keep your hands and feet away from the cutting

units. Keep clear of the discharge opening.

•Do not mow with the discharge deector

raised, removed, or altered unless there is a

grass-collection system or mulch kit in place and

working properly .

•Do not mow in reverse unless it is absolutely

necessary . Always look down and behind you

before moving the machine in reverse.

•Use extreme care when approaching blind

corners, shrubs, trees, or other objects that may

block your view .

•Stop the blades whenever you are not mowing.

•If the machine strikes an object or starts to vibrate,

immediately shut of f the engine, remove the key

(if equipped), and wait for all moving parts to stop

before examining the machine for damage. Make

all necessary repairs before resuming operation.

•Slow down and use caution when making turns

and crossing roads and sidewalks with the

machine. Always yield the right-of-way .

•Before you leave the operating position, do the

following:

– Park the machine on a level surface.

– Disengage the power takeof f and lower the

attachments.

– Engage the parking brake.

– Shut of f the engine and remove the key .

– W ait for all moving parts to stop.

•Operate the engine only in well-ventilated areas.

Exhaust gases contain carbon monoxide, which

is lethal if inhaled.

•Never leave a running machine unattended.

•Attach towed equipment to the machine only at

the hitch point.

•Do not operate the machine unless all guards and

safety devices, such as the deectors and the

entire grass catcher , are in place and functioning

properly . Replace worn or deteriorated parts when

necessary .

•Use only accessories and attachments approved

by T oro.

•This machine produces sound levels in excess

of 85 dBA at the operator ’ s ear and can cause

hearing loss through extended periods of

exposure.

18

La page charge ...

Toro TimeCutter MX 4275T 107 cm Zero Turn Riding Mower 74691 Manuel utilisateur

Ce manuel convient également à

Toro TimeCutter MX 4275T 107 cm Zero Turn Riding Mower 74691 Manuel utilisateur

dans d''autres langues

Documents connexes