Worx WG748E Battery-Powered Lawn Mower Manuel utilisateur

Catégorie
Scarificateurs de pelouse
Taper
Manuel utilisateur
WG748E WG748E.X
P08
P18
P29
P40
P51
P62
P73
P84
P94
P104
P113
P125
P137
P148
P160
P170
P181
Cordless Lawn Mower
Schnurloser Rasenmäher
Tondeuse à gazon sans fil
Tosaerba senza fili
Cortacésped a batería
Corta-relva sem fios
Snoerloze graasmaaier
Ledningsfri plæneklipper
Batteridrevet gressklipper
Sladdlös gräsklippare
Bezprzewodowa kosiarka do trawników
 μ μ
Vezetékmentes fűnyíró
Maşină de tuns iarba fără fir
Bezdrátová travní sekačka
Akumulátorová kosačka na trávu
Brezžična kosilnica
EN
D
F
I
ES
PT
NL
DK
NOR
SV
PL
GR
HU
RO
CZ
SK
SL
Original Instruction
Originalbetriebsanleitung
Notice originale
Istruzioni originali
Manual original
Manual original
Oorspronkelijke gebruiksaanwijzing
Original brugsanvisning
Original driftsinstruks
Bruksanvisning i original
Instrukcja oryginalna
 Ω ΩΩ ΔΩ
Eredeti használati utasítás
Instrucţiuni originale
Původní návod k používání
Pôvodný návod na použitie
Izvirna navodila
EN
D
F
I
ES
PT
NL
DK
NOR
SV
PL
GR
HU
RO
CZ
SK
SL
10
11 12
9
8
7
6
1
2
3
4
5
2
1 1
C2 C3
A1 A2
C1
B
1
2
F2 G1
D1 D2
F1
E
1
2
1
2
13
14
100%
0%
J
G2 H
I2I1
1
2
7 — 80mm
6 — 70mm
5 — 60mm
4 — 50mm
3 — 40mm
2 — 30mm
1 — 20mm
15
K1
1
1
2
M-1
M-2
M-3
N1
N2
K2
M
L
17
18
16
8
Cordless Lawn Mower EN
PRODUCT SAFETY
GENERAL SAFETY WARNINGS
WARNING Read all
safety warnings and all
instructions.
Failure to follow
the warnings and instructions
may result in electric shock,
fire and/or serious injury.
Carefully read the
instructions for the safe
operation of the machine.
Save all warnings and
instructions for future
reference.
- This appliance is not
intended for use by persons
(including children) with
reduced physical, sensory
or mental capabilities,
or lack of experience
and knowledge, unless
they have been given
supervision or instruction
concerning use of the
appliance by a person
responsible for their safety.
- Children should be
supervised to ensure that
they do not play with the
appliance.
- The appliance is only to be
used with the power supply
unit provided with the
appliance.
IMPORTANT
READ CAREFULLY BEFORE
USE
KEEP FOR FUTURE
REFERENCE
Safe operation practices
Training
a) read the instructions
carefully. Be familiar with
the controls and the proper
use of the equipment;
b)never allow children or
people unfamiliar with
these instructions to
use the lawnmower. Local
regulations can restrict the
age of the operator;
c)never mow while people,
especially children, or pets
are nearby;
d) keep in mind that the
operator or user is
responsible for accidents
or hazards occurring
to other people or their
property
Preparation
a) While mowing, always
wear substantial footwear
and long trousers. Do not
operate the equipment
when barefoot or wearing
open sandals;
b) thoroughly inspect the
9
Cordless Lawn Mower EN
area where the equipment
is to be used and remove
all objects which can be
thrown by the machine;
c) Before using, always
visually inspect to see that
the blades, blade bolts and
cutter assembly are not
worn or damaged. Replace
worn or damaged blades
and bolts in sets to preserve
balance. Replace damaged
and unreadable labels.
Operation
a) mow only in daylight or in
good artificial light;
b) avoid operating the
equipment in wet grass,
where feasible;
c) always be sure of your
footing on slopes;
d) walk, never run;
e) for wheeled rotary
machines, mow across the
face of slopes, never up
and down;mow across the
face of slopes, never up and
down.
f) exercise extreme caution
when changing direction on
slopes;
g) do not mow excessively
steep slopes;
h) use extreme caution when
reversing or pulling the
lawnmower towards you;
i) stop the blade(s) if the
lawnmower has to be
tilted for transportation
when crossing surfaces
other than grass, and
when transporting the
lawnmower to and from the
area to be mowed;
j) never operate the
lawnmower with defective
guards , or without safety
devices, for example
deflectors and/or grass
catchers, in place;
k) switch on the motor
carefully according to
instructions and with feet
well away from the blade(s);
l) do not tilt the lawnmower
when switching on the
motor, except if the
lawnmower has to be tilted
for starting. In this case,
do not tilt it more than
absolutely necessary and
lift only the part which is
away from the operator;
m)do not put hands or feet
near or under rotating parts.
Keep clear of the discharge
opening at all times;
n) not to touch the blades
before the disabling device
has been removed and
the blades have come to a
10
Cordless Lawn Mower EN
complete stop;
o) Do not start the lawnmower
when standing in front of
the discharge opening.
p) Do not transport the
lawnmower while the power
source is running.
q) Stop the lawnmower,and
remove the disabling
device. Make sure that all
moving parts have come to
a complete stop.
whenever leaving the
machine unattended,
before clearing a blockage,
before checking, cleaning
or working on the machine,
after striking a foreign
object. Inspect the
machine for damage
and make repairs before
restarting and operating the
lawnmower
If the lawnmower starts to
vibrate abnormally (check
immediately)
- inspect for damage.
- replace or repair any
damaged parts.
- check and tighten any loose
parts.
Maintenance and storage
a)keep all nuts, bolts and
screws tight to be sure
the equipment is in safe
working condition;
b)check the grass cacher
frequently for wear or
deterioration;
c)replace worn or damaged
parts for safety. Use only
genuine replacement parts
and accessories.
d)Be careful during adjusting
of the lawnmower to
prevent entrapment of the
fingers between moving
blades and fixed parts of
the lawnmower.
e)Always allow the
lawwnmower to cool down
before storing.
f) When servicing the blades
be aware that, even though
the power source is
switched off, the blades can
still be moved.
SAFETY WARNINGS FOR
BATTERY PACK
a) Do not dismantle, open
or shred cells or battery
pack.
b) Do not short-circuit a
battery pack. Do not
store battery packs
haphazardly in a box or
drawer where they may
short-circuit each other
or be short-circuited by
conductive materials.
11
Cordless Lawn Mower EN
When battery pack is not
in use, keep it away from
other metal objects, like
paper clips, coins, keys,
nails, screws or other small
metal objects, that can
make a connection from
one terminal to another.
Shorting the battery
terminals together may
cause burns or a fire.
c) Do not expose battery
pack to heat or fire.
Avoid storage in direct
sunlight.
d) Do not subject battery
pack to mechanical
shock.
e) In the event of battery
leaking, do not allow
the liquid to come into
contact with the skin or
eyes. If contact has been
made, wash the affected
area with copious
amounts of water and
seek medical advice.
f) Keep battery pack clean
and dry.
g) Wipe the battery pack
terminals with a clean
dry cloth if they become
dirty.
h) Battery pack needs to
be charged before use.
Always refer to this
instruction and use
the correct charging
procedure.
i) Do not maintain battery
pack on charge when not
in use.
j) After extended periods
of storage, it may be
necessary to charge and
discharge the battery
pack several times
to obtain maximum
performance.
k) Do not use any battery
pack which is not
designed for use with the
equipment.
l) Recharge only with
the charger specified
by WorxNITRO. Do not
use any charger other
than that specifically
provided for use with the
equipment.
m)Keep battery pack out of
the reach of children.
n) Retain the original
product literature for
future reference.
o)Remove the battery from
the equipment when not
in use.
p) Dispose of properly.
q) Do not mix cells of
different manufacture,
capacity, size or type
12
Cordless Lawn Mower EN
within a device.
r) Keep the battery away
from microwaves and
high pressure.
SYMBOLS
Read instruction handbook before
operation this machine
Keep bystanders away.
Beware of sharp blades. Blades
continue to rotate after the motor
is switched off- Remove disabling
device before maintenance
Batteries may enter water cycle if
disposed improperly, which can
be hazardous for ecosystem. Do
not dispose of waste batteries as
unsorted municipal waste.
Do not burn
Li-Ion battery This product has been
marked with a symbol relating to
‘separate collection’ for all battery
packs and battery pack. It will
then be recycled or dismantled in
order to reduce the impact on the
environment. Battery packs can be
hazardous for the environment and
for human health since they contain
hazardous substances.
Waste electrical products should
not be disposed of with household
waste. Please recycle where
facilities exist. Check with your Local
Authority or retailer for recycling
advice.
Wear protective gloves.
Remove battery from the socket
before carrying out any adjustment,
servicing or maintenance.
Remove the key
Blade continues to rotate after
the machine is switched off. Wait
until all machine components have
completely stopped before touching
them
COMPONENT LIST
1. OPERATING BAIL
2. HANDLE BAR
3. GRASS COLLECTION BAG
4. CUTTING HEIGHT ADJUSTMENT LEVER
5. CUTTING HEIGHT ADJUSTMENT POINTER
6. FRONT HANDLE
7. BATTERY PACK COVER
8. REAR HANDLE
9. SAFETY FLAP
10. SAFETY LOCKOUT BUTTON
11. QUICKRELEASE BUTTON
12. MULCHING INSERT
13. BATTERY PACK SEE FIG. F2
14. SAFETY KEY SEE FIG. F2
15. POWER INDICATOR LIGHTSEE FIG. H
16. BLADE BOLT SEE FIG. N1
13
Cordless Lawn Mower EN
17. BLADE SEE FIG.N1
18. SPACER SEE FIG. N1
*Not all the accessories illustrated or described are
included in standard delivery.
TECHNICAL DATA
Type WG748E WG748E.X (7- designation of machin-
ery, representative of Cordless Lawn Mower)
WG748E WG748E .X**
Voltage 40V Max.(2x20V Max.)***
No load speed 2800/min
Deck width 48 cm
Cutting width 46 cm
Front wheel diameter 200 mm
Rear wheel diameter 230 mm
Cutting height 20 – 80 mm
Cutting height positions 7
Grass collection capacity 55 L
Machine Weight (bare tool) 25.3 kg
** X=1-999, A-Z, M1-M9 are only used for different
customers, there are no safe relevant changes between
these models.
*** Voltage measured without workload. Initial battery
voltage reaches maximum of 20 volts. Nominal voltage is
18 volts.
Category Type Capacity
20V Battery WA3014 4.0 Ah
20V Charger WA3883 4.0 A
We recommend that you purchase your accessories from
the same store that sold you the tool. Choose the type
according to the work you intend to undertake. Refer to the
accessory packaging for further details. Store personnel
can assist you and offer advice.
NOISE DATA
A weighted sound pressure LpA = 78.4 dB(A)
KpA 3.0 dB (A)
A weighted sound power LwA = 91.6 dB(A)
KwA 3.0 dB (A)
Wear ear protection
VIBRATION INFORMATION
Typical weighted vibration ah <2.5 m/s
Uncertainty K = 1.5 m/s
WARNING The vibration emission value during actual
use of the power tool can differ from the declared
value depending on the ways in which the tool is used
dependant on the following examples and other variations
on how the tool is used:
How the tool is used and the materials being cut or drilled.
The tool being in good condition and well maintained.
Using the correct accessory for the tool and ensuring it is
sharp and in good condition.
The tightness of the grip on the handles and if any anti
vibration accessories are used.
And the tool is being used as intended by its design and
these instructions.
This tool may cause hand-arm vibration syndrome if its
use is not adequately managed
WARNING To be accurate, an estimation of exposure
level in the actual conditions of use should also take
account of all parts of the operating cycle such as the times
when the tool is switched off and when it is running idle but
not actually doing the job. This may significantly reduce the
exposure level over the total working period.
Helping to minimise your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades.
Maintain this tool in accordance with these instructions and
keep well lubricated (where appropriate).
If the tool is to be used regularly then invest in anti vibration
accessories.
Plan your work schedule to spread any high vibration tool use
across a number of days.
OPERATION INSTRUCTION
NOTE: Read instruction handbook before
operation this machine.
INTENDED USE
This product is intended for domestic lawn mowing.
ASSEMBLY & OPERATION
ACTION FIGURE
ASSEMBLY
14
Cordless Lawn Mower EN
Assembling the handle bar &
Adjusting Handle’s height
NOTE: Press and hold
Quick-release button during
operation.
See Fig. A1, A2
Assembling the grass
collection bag See Fig. B
Assembling the grass
collection bag to the lawn
mower
NOTE: Depress the grass
collection bag slightly to
ensure that it is completely
installed.
NOTE: Take the mulching insert
out of the lawn mower before
fitting the grass collection bag.
See Fig. C1, C2, C3
Removing/emptying grass
collection bag
WARNING! Always check
the safety flap close the
discharge outlet before using.
Never lift the safety flap when
the lawn mower is being used
without fitted grass collection
bag.
See Fig. D1,D2
Installing mulching insert See Fig. E
Removing /fitting the battery
pack
Insert the safety key before
installing the battery pack.
NOTE: This machine will only
run when sp - batteries are
installed. It is recommended to
use the same AH batteries and
charge the two batteries at the
same time.
When you use two batteries
with different AH, the machine
will only run to the lower
common denominator.
See Fig. F1, F2
Checking the battery charge
condition
NOTE: Fig. G1 only applies for
the battery pack with battery
indicator light.
See Fig.G1
Charging the battery pack
NOTE: The batteries are
shipped uncharged. Each
battery must be fully charged
before the first mow.
Always fully charge the two
batteries at same time.
More details can be found in
chargers manual.
See Fig.G2
OPERATION
Power indicator light
See details in BATTERY STATUS
part
IMPORTANT:
When only one light is
illuminated, your battery
is overly discharged, even
though the machine may
still be capable to work.
Continuing to operate
your machine with the
battery in this discharged
condition may reduce the
life and performance of your
battery.
When no light is illuminated,
at least one battery is not
fully installed or battery
may be defective, please
double check the batteries
are fully seated into
position.
See Fig.H
Starting and Stopping See Fig.I1,I2
Adjusting the cutting height
WARNING! Stop, release
Operating Bail and wait
until the motor stops before
adjusting height. The blades
continue to rotate after the
machine is switched off, a
rotating blade can cause injury.
Do not touch rotating blades.
See Fig. J
Storage See Fig. ,K1,K2
BATTERY STATUS (See Fig. H)
Before starting or after use, press the button beside
the power indicator light on the machine to check the
battery capacity.
During operation, the battery capacity will be indicated
automatically by the battery power indicator. The
indicator constantly senses and displays the battery
condition as follows.
Charge the machine with 2 battery packs with different
AH ,the power indicator light displays the battery
condition with the lower one of the two batteries.
Battery indicator
light status Battery condition
Five green lights
( ) are
illuminated.
The two batteries are in a highly
charged condition.
Two, three or four
green lights are
illuminated.
The two batteries have a remain-
ing charge. The more lights are
illuminated, the more battery
capacity.
15
Cordless Lawn Mower EN
Only one green
light ( ) is
illuminated.
The battery level of at least one
battery pack is very low. Please
check and charge the battery
pack.
No light is
illuminated.
At least one battery is not fully
installed or battery may be defec-
tive.
Only one light is
flashing twice per
cycle.
At least one battery is over
discharged (please refer to the
battery charge condition), please
recharge the two batteries at
once before use again or storage.
Only one light is
flashing three times
per cycle.
At least one battery is hot, wait
for them cool down before start
again.
Only one light is
flashing four times
per cycle.
The machine is over load. Raise
the cutting height or push slowly.
MULCHING MOWING TIPS
While mulching, your new mower is designed to cut the
grass clippings into small pieces and distribute them
back into the lawn. Under normal conditions, the mulched
grass will biodegrade quickly and deliver nutrients to the
lawn. Please review the following recommendations for
optimum mulching performance.
1) Avoid mowing when the grass is wet from rain or dew.
Wet grass may form clumps which interfere with the
mulching action and reduce the runtime. The best time
to mow the grass is in the late afternoon when the grass
is dry and the newly cut area will not be exposed to
direct sunlight.
2) For the best mulching performance, set the cutting
height to remove about one third of the grass blade
length, ideally no more than 40mm at one time. If the
lawn is overgrown, it may be necessary to increase the
cutting height to reduce the pushing effort and prevent
overloading the motor. For extremely heavy mulching,
it is advisable to first cut at a high cut height setting,
and then re-cut to the final cut height. Otherwise, make
narrower cuts and mow slowly.
3) For the best performance, keep the mower housing
free of built-up grass. From time to time turn off mower
and wait for the blades to come to a complete stop.
Then Remove the safety key and turn mower on its
side. Using an object such as a stick, wipe out any
accumulation of grass around the blade area. Be careful
of the sharp edges of the blade. Ensure to clean the
blade area often when cutting wet or new grass and
every time after the machine is used.
4) Certain types of grass or grass conditions may require
that an area be mulched a second time to fully disperse
the grass throughout the lawn. If cutting a second time,
it is advisable to cut perpendicular (across) the first cut
pattern. DO NOT CHANGE CUT PATTERN IN ANY WAY
THAT WOULD CAUSE MOWING DOWN A HILL.
5) Change your cutting pattern from week to week. This
will help prevent matting and graining of the lawn.
CUTTING AREA
The cutting area can be affected by several factors, such
as cutting height, lawn humidity, grass length and density.
Besides, starting and stopping the mower too many times
during operation will reduce the cutting area.
The table below gives the relationship between cutting
conditions and cutting area.
Cutting Height Recommend lot size
(maximum)
Cutting off 8cm to 6cm With 2*20V / 4.0Ah batteries
up to 500m
2
*
* Used with two fully charged battery packs.
TIPS:
1) It is recommended to mow your lawn more frequently,
walk at normal pace, and not to start/stop the mower
too often during operation.
2) For best performance, please ensure use two fully
charged battery packs at the same time and always cut
off 1/3 or less of the grass height.
3) Walk slowly when cutting long grass, so as to have more
effective cutting and properly discharge the clippings.
4) Avoid cutting wet grass, otherwise it will stick to the
underside of the deck and the clippings cannot be
collected or discharged properly.
5) A higher cutting height shall be applied to new or thick
grass and it will extend the battery duration.
MAINTENANCE
WARNING: Stop the mower, remove the safety
key and batteries before removing the grass
collection bag.
Note: To ensure long and reliable service, perform the fol-
lowing maintenance procedures regularly. Check for obvious
defects such as a loose, dislodged or a damaged blade, loose
fittings, and worn or damaged components. Check that
the covers and guards are all undamaged and are correctly
attached to mower. Carry out any necessary maintenance or
repairs before operating mower. If the mower should happen
to fail despite regular maintenance, please call our customer
helpline for advice.
BLADE SHARPENING
KEEP BLADE SHARP FOR BEST MOWER PERFORMANCE. A
DULL BLADE DOES NOT CUT GRASS CLEANLY OR MULCH
PROPERLY.
WEAR PROPER EYE PROTECTION WHILE REMOVING, SHARP-
ENING, AND INSTALLING BLADE. ENSURE THAT SAFETY KEY
AND BATTERIES ARE REMOVED.
Sharpening the blade twice during a mowing season is
usually sufficient under normal circumstances. Sand causes
the blade to dull quickly. If your lawn has sandy soil, more
16
Cordless Lawn Mower EN
frequent sharpening may be required.
REPLACE BENT OR DAMAGED BLADE IMMEDIATELY.
WHEN SHARPENING THE BLADE (See Fig. L)
1. Make sure blade remains balanced.
2. Sharpen blade at the original cutting angle.
3. Sharpen cutting edges on both ends of blade to keep it
balanced, removing equal amounts of material from both
ends.
Note:
1. Be sure the mower is turned off . Remove the key and
batteries.
2. Place the mower in stand up storage mode.
BLADE BALANCING (See Fig. M)
Check balance of blade by placing center hole in blade M-1
over a screwdriver shank M-2, clamped horizontally in a vise
M-3. If either end of the blade rotates downward, file that
end. Blade is properly balanced when neither end drops.
BLADE MAINTENANCE (See Fig. N1, N2)
Replace yourMower Blade after 50 hours mowing or 2 years,
which ever is the sooner-regardless of condition.
Follow these procedures to remove and replace the Blade.
You will need garden gloves (not provided) and a spanner
wrench (not provided) to remove the Blade. Make sure safety
key and batteries are not installed. Wedge a block of wood
between the blade and the mower deck to prevent the blade
from turning and unscrew the Blade Bolt counter-clockwise
using a spanner wrench, and then remove the Blade.
To re-assemble, position the Blade with the cutting edges
towards the ground. Then securely tighten the Blade Bolt.
STORAGE (See Fig. K1,K2)
Stop the mower, and always remove the Safety Key and bat-
teries. Clean the exterior of the machine thoroughly using a
soft brush and cloth. Do not use water, solvents or polishes.
Remove all grass and debris, especially from the ventilation
slots.
Turn the machine on its side and clean the blade area. If
grass cuttings are compacted in the blade area, remove with
a wooden or plastic implement.
Store the machine in a dry place. Do not place other objects
on top of the machine.
To aid storage, Press and hold Quick-release button, and fold
the Handle bar.
ENVIRONMENTAL
PROTECTION
Waste electrical products must not be disposed of
with household waste. Please recycle where facilities
exist. Check with your local authorities or retailer for
recycling advice.
TROUBLESHOOTING
PROBLEM SOLUTION
1. Mower doesn’t
run when
Operating Bail is
activated.
A. Check to make sure safety key has
been installed and is fully seated
and that Safety lock-out button is
completely pushed.
B. Release Operating Bail to turn
mower off. Remove safety key and
batteries, turn mower over and check
that blade is free to turn. If not free,
return to an authorized servicer.
Blade should turn freely.
C. Has battery been fully charged?
Plug in charger and wait for green
light to come on.
2. Motor stops
while mowing. A. Release Operating Bail to turn
mower off. Remove safety key and
batteries,turn mower over and check
that blade is free to turn. If not free,
return to an authorized servicer.
Blade should turn freely.
B. Raise cutting height of wheels to
highest position and start mower.
C. Has battery been fully charged?
Plug in charger and wait for green
light to come on.
D. Avoid overloading the mower. Slow
down the cutting pace by pushing
mower slower or raise the cut height.
Or both.
3. Mower runs
but cutting
performance is
unsatisfactory,
or does not cut
entire lawn.
A. Has battery been fully charged? Plug
in charger and wait for green light to
come on.
B. Release Operating Bail to turn mower
off. Remove safety key and batteries.
Turn mower over and check: Blade for
sharpness - Keep blade sharp. Deck and
discharge chute for clogging.
C. Wheel height adjustment may be set
too low for grass condition. Raise cutting
height.
4. Mower is too
hard to push. A. Raise cutting height to reduce
deck drag on grass. Check each
wheel for free rotation.
17
Cordless Lawn Mower EN
5. Mower is
abnormally
noisy and
vibrates.
A. Release Operating Bail to turn
mower off. Remove safety key
and batteries. Turn mower on
side and check blade to ensure it
has not been bent or damaged. If
blade is damaged, replace with a
replacement blade. If the underside
of the deck is damaged return mower
to an Authorized service center.
B. If there is no visible damage to the
blade and the mower still vibrates:
Release Operating Bail to turn mower
off, Remove safety key and batteries,
and remove blade. Rotate blade 180
degrees and retighten. If mower
still vibrates, return the mower to an
authorized service center.
6. Battery
charger LED’s
not on.
A. Check plug connection.
B. Replace charger.
7. Battery
charger LED
does not flip to
green.
A. Battery needs to be diagnosed.
Take to authorized service center.
8. Mower not
picking up
clippings with
the Grass
Collection Bag.
A. Remove mulch plate when
bagging.
B. Chute clogged. Release Operating
Bail to turn mower off. Remove safety
key and batteries. Clear chute of
grass clippings.
C. Too much cut grass. Raise cutting
height of wheels to shorten length
of the cut.
D. Bag full. Empty bag more often.
9. When
mulching there
are clippings
visible.
A. Too much cut grass. Raise cutting
height of wheels to shorten length of
the cut. Do not cut off more than 1/3
of total length.
B. Check blade for sharpness. Always
keep blade sharp.
10. Low or
diminished run-
time after many
uses
A. Return to Authorized Service
location - may need new battery.
11. The battery
charger LED
flashes red and
the battery can’t
be charged.
A. The battery overheats after
continuous use. Remove battery
from the charger and allow it to cool
to 42°C or less.
DECLARATION OF CONFORMITY
We,
Positec Germany GmbH
Postfach 32 02 16, 50796 Cologne, Germany
On behalf of Positec declare that the product
Description WorxNITRO Cordless Lawn Mower
Type WG748E WG748E.X (7- designation of
machinery, representative of Cordless Lawn Mower)
Function mowing grass
Complies with the following Directives,
2006/42/EC, 2014/30/EU
2011/65/EU&(EU)2015/863
2000/14/EC amended by 2005/88/EC
2000/14/EC amended by 2005/88/EC
Conformity assessment procedure as per Annex VI.
Measured Sound Power Level 91.6 dB(A)
Declared Guaranteed Sound Power Level 94
dB(A)
The notified body involved
Name: Intertek, Deutschland GmbH (notified body
0905)
Address: Stangenstraße 1, 70771 LEINFELDEN-
ECHTERDINGEN
Standards conform to,
EN 60335-1, EN 60335-2-77, EN 62233, EN ISO 3744, EN
55014-1, EN 55014-2
The person authorized to compile the technical file,
Name: Marcel Filz
Address Positec Germany GmbH
Postfach 32 02 16, 50796 Cologne, Germany
2021/10/11
Allen Ding
Deputy Chief Engineer, Testing & Certification
Positec Technology (China) Co., Ltd
18, Dongwang Road, Suzhou Industrial
Park, Jiangsu 215123, P. R. China
18
Schnurloser Rasenmäher D
PRODUKTSICHERHEIT
ALLGEMEINE
SICHERHEITSHINWEISE
WARNUNG Lesen Sie
alle
Sicherheitshinweise und
Anweisungen. Versäumnisse
bei der Einhaltung der
Sicherheitshinweise und
Anweisungen können
elektrischen Schlag, Brand
und/oder schwere
Verletzungen verursachen.
Lesen Sie die
Bedienungsanleitung
zum sicheren Betrieb
des Gerätes aufmerksam
durch.
Bewahren Sie alle
Sicherheitshinweise und
Anweisungen für die
Zukunft auf.
- Dieses Gerät ist nicht dafür
bestimmt, durch Personen
(einschließlich Kinder)
mit eingeschränkten
physischen, sensorischen
oder geistigen Fähigkeiten
oder mangels Erfahrung
und/oder mangels Wissen
benutzt zu werden, es sei
denn, sie werden durch
eine für ihre Sicherheit
zuständige Person
beaufsichtigt oder erhielten
von ihr Anweisungen, wie
das Gerät zu benutzen ist.
- Kinder sollten beaufsichtigt
werden um Sicherzustellen,
dass sie nicht mit dem
Ladegerät spielen.
- Das Gerät darf nur mit dem
mitgelieferten Netzteil
verwendet werden.
WICHTIG
VOR GEBRAUCH BITTE
GENAU DURCHLESEN
FÜR SPÄTERE BEZUGNAHME
AUFBEWAHREN
Sicherer Betrieb
Training
a) Die Anweisungen
aufmerksam durchlesen.
Machen Sie sich mit den
Bedienelementen und
dem vorschriftsmäßigen
Gebrauch des Rasenmähers
vertraut.
b) Niemals Kindern oder
mit diesen Anweisungen
nicht vertrauten Personen
erlauben, den Rasenmäher
zu benutzen. Nationale
Vorschriften können das
Alter der Bedienperson
möglicherweise
beschränken.
c) Niemals mähen,
während sich Personen,
insbesondere Kinder, oder
19
Schnurloser Rasenmäher D
Tiere in unmittelbarer Nähe
aufhalten.
d) Bedenken Sie, dass der
Bediener oder Benutzer bei
Unfällen oder Gefährdungen
anderer Personen oder
deren Eigentum die
Verantwortung trägt!
Vorbereitung
a) Tragen Sie beim Mähen
stets festes Schuhwerk
und eine lange Hose. Den
Rasenmäher nicht barfuß
oder mit offenen Sandalen
benutzen.
b) Inspizieren Sie die Gegend,
in der die Ausrüstung
eingesetzt werden soll,
gründlich und entfernen Sie
alle Objekte, die durch die
Maschine aufgeschleudert
werden könnten.
c) Vor der Benutzung immer
durch Augenschein
prüfen, ob Messer,
Messerschrauben und
Schneidbalken abgenutzt
oder beschädigt sind.
Abgenutzte Messer und
Schrauben nur im ganzen
Satz auswechseln, um
Unwuchten zu vermeiden.
Tauschen Sie beschädigte
und unleserliche Etiketten
aus.
Betrieb
a) Nur bei Tageslicht oder
gutem künstlichen Licht
mähen.
b) Nach Möglichkeit nicht in
nassem Gras arbeiten.
c) Auf schrägen Flächen stets
auf sicheren Tritt achten.
d) Gehen Sie; rennen Sie
niemals mit dem Gerät;
e) Mähen Sie bei
Rotormaschinen mit Rädern
Abhänge niemals auf hinaus
oder hinab, sondern immer
seitlich am Hang entlang;
f) Beim Richtungswechsel
an Abhängen äußerst
vorsichtig sein.
g) Keine besonders steilen
Abhänge mähen.
h) Beim Rückwärtsgehen oder
Ziehen des Rasenmähers
äußerst vorsichtig sein.
i) Die Messer müssen stehen,
wenn der Rasenmäher
für den Transport gekippt
werden muss, wenn nicht
mit Gras bepflanzte Flächen
überquert werden und beim
Transport vom und zu dem
zu mähenden Bereich.
j) Den Rasenmäher auf
keinen Fall mit defekten
Schutzvorrichtungen oder
Schutzblechen, oder ohne
20
Schnurloser Rasenmäher D
ordnungsgemäß montierte
Sicherheitseinrichtungen
wie z. B. Prallbleche und/
oder Grasfangvorrichtung
betreiben.
k) Den Motor wie in den
Anweisungen beschrieben
starten und dabei darauf
achten, dass die Füße
ausreichend weit von den
Messern entfernt sind.
l) Den Rasenmäher beim
Starten des Motors nicht
kippen, es sei denn,
es ist für das Anlaufen
erforderlich. In diesem
Fall nur so weit wie nötig
und nur auf der Bediener
abgewandten Seite kippen.
m) Hände und Füße nicht
in die Nähe oder unter
rotierende Teile bringen.
Bei Rotormäher die
Austragsöffnung unbedingt
freihalten.
n) Sie dürfen die Klingen
nicht berühren, bevor die
Sperrvorrichtung entfernt
worden ist und die Klingen
vollständig zum Stillstand
gekommen sind;
o) Starten Sie den
Rasenmäher nicht, wenn
Sie vor der Auslassöffnung
stehen.
p) Transportieren Sie den
Rasenmäher nicht, wenn die
Stromquelle eingeschaltet
ist.
q) Stoppen Sie den
Rasenmäher und
entfernen Sie die
Deaktivierungsvorrichtung
.
Stellen Sie sicher, dass
die beweglichen Teile zum
vollständigen Stillstand
gekommen sind.
Sie die Maschine
unbeaufsichtigt lassen,
Sie ein Hindernis
wegräumen,
Sie die Maschine
überprüfen, säubern oder
an der Maschine arbeiten,
nach der Kollision mit
einem Fremdkörper.
Den Rasenmäher
auf Beschädigungen
untersuchen und wenn
notwendig instand setzen
lassen
Falls der Rasenmäher
plötzlich ungewöhnlich
stark zu vibrieren beginnt
(sofort prüfen)
– Auf Schädenhininspizieren.
– Beschädigte Teile
austauschen oder
reparieren.
Lose Teile überprüfen und
festziehen.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192

Worx WG748E Battery-Powered Lawn Mower Manuel utilisateur

Catégorie
Scarificateurs de pelouse
Taper
Manuel utilisateur