Chief Chief Manuel utilisateur

Catégorie
Mur
Taper
Manuel utilisateur

Ce manuel convient également à

INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Portrait Adapter Bracket
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
TA410
TA410 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all equipment and accessories mounted on the TA410
bracket does not exceed the weight limits specified in the
installation instructions of the mount to which it is being
attached.
DIMENSIONS
16.50
419.1
.44
11.1
.10
DEPTH ADDED
TO MOUNT
2.7
7.87
200
7.87
200
SHOWN
WITH
INTERFACE
(NOT INCLUDED)
Installation Instructions TA410
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
TA410 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
1/8" (included)
#2
7/16"
1/2"
A (1)
[adapter bracket]
B (4)
5/16-18 x 1/2"
C (4)
[spacer]
G (4) 1/8"
H (1)
#10-24 x 1/2"
D (4)
[washer] E (4)
1/4-20
F (4)
5/16-18
Installation Instructions TA410
5
Installation
1. Remove two hex nuts and mounting buttons from top
interface support of swing arm. (See Figure 1)
Figure 1
2. Attach interface brackets to display according to swing arm
mount installation instructions.
3. Select proper hex nuts to use in Step 4.
Use 5/16-18 hex nuts (E) if installing to TS525 or
iCF50 (large) mount
Use 1/4-20 hex nuts (F) if installing to TS3XX or
iCF30 (medium) mount
4. Use four selected nuts (E or F), four washers (D) and four
spacers (C) to attach adapter bracket (A) to interface
brackets. (See Figure 2)
5. Use four #10-24 x 1/2" button head cap screws (G) to
secure adapter bracket (A) to interface brackets. (See
Figure 2)
Figure 2
6. Install two 5/16-18 x 1/2" Phillips pan machine screws (B)
into top two 200 x 200mm holes on adapter bracket (A).
(See Figure 3)
NOTE: Do not fully tighten screws into bracket! Let screws
hang out at least 1/4" in order to allow the screws to
hang onto faceplate in next step!
Figure 3
(medium interface)
1
X 2
(large interface)
top interface support
top interface support
1
X 2
mounting button
mounting button
(E or F) x 4
4
(D) x 4
(C) x 4
(G) x 4
5
(A)
6
(B) x 2
(A)
top of display
TA410 Installation Instructions
6
7. Hang display onto faceplate inserting two installed Phillips
machine screws (B) into upper mounting holes. (See Figure
4)
8. Secure adapter bracket to faceplate by installing two 5/16-
18 x 1/2" Phillips pan machine screws (B) through lower two
200 x 200mm mounting holes on faceplate and adapter
bracket. (See Figure 4)
9. Tighten all four screws (B) to fully secure adapter bracket
(A) to faceplate.
Figure 4
7
8
(B) x 2
(TS318TU shown)
Installation Instructions TA410
7
TA410 Installation Instructions
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P800.582.6480 / 952.894.6280
F877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P+31 (0)40 2668620
F+31 (0)40 2668615
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief Manufacturing, a products divi-
sion of Milestone AV Technologies
8805-002020 Rev00
2011 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
06/11
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief Chief Manuel utilisateur

Catégorie
Mur
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues