CIARRA CBCB6736G-OW Manuel utilisateur

  • Bonjour ! Je suis un chatbot IA spécialement formé pour vous aider avec le CIARRA CBCB6736G-OW Manuel utilisateur. J’ai déjà parcouru le document et peux vous fournir des réponses claires et précises.
ENGLISH
INSTALLATION AND USER'S MANUAL
Page
1-23
DEUTSCH
BENUTZERHANDBUCH&INSTALLATION
SANLEITUNG
Seite
24-46
FRANÇAIS
MANUEL DE L’UTILISATEUR ET
D’INSTALLATION
Page
47-69
ITALIANO
INSTALLAZIONE E MANUALE
DELL’UTENTE
Pagina
70-92
ESPAÑOL
MANUAL DE USUARIO E
INSTRUCCIONES DE INSTALACIÓN
Página
93-115
NEDERLANDS
INSTALLATIE- EN
GEBRUIKERSHANDLEIDING
Pagina
116-138
SVENSKA
INSTALLATION- OCH
BRUKSANVISNING
Sida
139-161
Phone Scaning, Hood Installing
www.ciarra.store
EN
Dear customer:
Congratulations on purchasing this device. This instruction manual is designed
to provide you with all required instructions related to the installation, use and
maintenance of the appliance. In order to operate the unit correctly and safety,
please read this instruction manual carefully before installation and usage.
The cooker hood use high quality materials, and is made with a streamlined
design. Equipped with large power electric motor and centrifugal fan, it also
provides strong suction power, low noise operation, non-stick grease filter and
easy assembly installation.
Scan the QR code to get access to contact CIARRA Amazon Service if you
have any question.
Scan to contact CIARRA Amazon Service
UK DE FR
IT ES NL
1
E-mail: info@ciarra.store
SE PL
EN
CONTENTS
Safety------------------------------------------------------------3-4
Specifications---------------------------------------------------5
Components-----------------------------------------------------5
Installation---------------------------------------------------6-13
Prepare for Installation---------------------------------------6
Recommended Tools for Installation---------------------7
Install the Hood--------------------------------------------8-12
Activated Carbon Filter Installation----------------------13
Operation---------------------------------------------------14-18
Cleaning and Maintenance----------------------------19-21
Motor
Grease Filter
Fan Blade
Activated Carbon Filter
Stainless Steel Cleaning
Painted Finish Cleaning
Bulb Replacement
Troubleshooting-----------------------------------------------22
Environmental Protection----------------------------------23
2
EN
Safety
! WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
Use this unit only in the manner intended by the manufacturer. If
you have questions, contact the manufacturer at the address or
telephone number listed in the warranty.
Before servicing or cleaning unit, switch power off at service panel
and lock the service disconnecting means to prevent power from
being switched on accidentally. When the service disconnecting
means cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
Installation work and electrical wiring must be done by a qualified
person(s) in accordance with all applicable codes and standards,
including fire-rated construction.
Sufficient air is needed for proper combustion and exhausting of
gases through the flue (chimney) of fuel burning equipment to
prevent back drafting.
When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
Ducted fans must always be vented to the outdoors.
Do not use this unit with any additional solid-state speed control
device.
This unit must be grounded.
When applicable local regulations comprise more restrictive
installation and/or certification requirements, the aforementioned
requirements prevail on those of this document and the installer
agrees to conform to these at his own expense.
TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:
1) Never leave surface units unattended at high settings. Boilovers
cause smoking and greasy spillovers that may ignite. Heat oils
slowly on low or medium settings.
2) Always turn hood ON when cooking at high heat or when flam
being food.
3) Clean ventilating fan frequently. Grease should not be allowed to
accumulate on fan, filters or in exhaust ducts.
4) Use proper pan size. Always use cookware appropriate for the size
of the surface element.
3
EN
Safety
! WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT
OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:
1. SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal
tray, then turn off the burner. BE CAREFUL TO PREVENT
BURNS. IF THE FLAMES DO NOT GO OUT IMMEDIATELY,
EVACUATE AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN — You may be burned.
3. DO NOT USE WATER, including wet dishcloths or towels — This
could cause a violent steam explosion.
4. Use an extinguisher ONLY if:
a) You own a Class ABC extinguisher and you know how to
operate it.
b) The fire is small and contained in the area where it started.
c) The fire department has been called.
d) You can fight the fire with your back to an exit.
! CAUTION
For indoor use only.
For general ventilating use only. Do not use to exhaust hazardous or
explosive materials and vapors.
To avoid motor bearing damage and noisy and/or unbalanced fan blade,
keep drywall spray, construction dust, etc. off range hood.
Your hood motor has a thermal overload which will automatically shut off
the motor if it becomes overheated. The motor will restart when it cools
down. If the motor continues to shut off and restart, have the hood
serviced.
Always follows the cooking equipment manufacturer’s requirements
regarding the ventilation needs.
To reduce the risk of fire and to properly exhaust air, be sure to duct air
outside — Do not exhaust air into spaces within walls or ceiling or into
attics, crawl space or garage.
When installing, servicing or cleaning the unit, it is recommended to wear
safety glasses and gloves.
Please read specification label on product for further information and
requirements.
4
EN
Specifications
Voltage
220V-240V~ 50Hz
Power of Motor
1 x 80W
Power of lamps
1x1W+2.5W(UV)
Cable length
1.5M
Appliance Dimension
595*330*810~1190mm
(W x D x H)
Components
5
EN
Installation
Prepare for installation:
a) If you have an outlet to the outside, your cooker hood can be connected as
below picture by means of an extraction duct (enamel, aluminum, flexible
pipe or inflammable material with an interior diameter of 150mm).
Choose a straight, short duct run to allow the hood to perform most
efficiently. Long duct runs, elbows and transitions will reduce the
performance of the hood. Use as few of them as possible. When possible,
use at least 2 foots straight runs before any turns. Larger ductwork may
be required for best performance with longer duct runs.
b) Before installation, turn the unit off and unplug it from the outlet.
c) The cooker hood should be placed at a distance of 65~75cm above the
cooking plane for best effect.
6
EN
Installation
Recommended Tools for Installation
Measuring tape
Phillips screwdriver no. 2
Flat blade screwdriver (to open knockout holes)
Drill, 1/8” drill bit and 1½” hole saw (to mark holes for ducting and cut
electrical access hole)
Wood shims (2) and wood screws (4) (required for standard installation to
framed cabinet)
Saw (to cut holes for ducted application)
Sheet metal shears (ducted installation only, for duct adjustment)
Pliers (ducted installation only, for duct adjustment)
Metal foil duct tape (for ducted applications)
Scissors (to cut metal foil duct tape)
Pencil
Wire stripper
Strain relief, 1/2” diameter (to secure house wiring cable to the hood)
CAUTION: Before proceeding to the installation, check the contents of
the box. If items are missing or damaged, contact the manufacturer.
Observe all governing codes and ordinances. Have a qualified
technician install the range hood. It is the installer’s responsibility to
comply with installation clearances specified on the model/serial rating
plate. The manufacturer declines all responsibility for improper
installation and does not accept responsibility for appliance warranty in
the event of damage caused by incorrect installation.
7
EN
Installation
Attention: Observe the warning in the instruction sheet concerning the
operation of the appliance when air is discharged from the room.
When the range hood and appliance supplied with energy other than electricity
are simultaneously in operation, the negative pressure in the room must be not
exceed 4 Pa (4×10-5 Bar).
Install the HoodVENT OUTSIDE:
1) If present, remove all protective poly film from the hood and/or parts.
2) Below is the hole drilling installation drawing:
3) According to the 1:1 hole drawing, Drill 3*Ø8mm holes to accommodate
the bracket. Screw and tighten the bracket onto the wall with the screws &
Wall plugs provided.
8
EN
Installation
4) Hang the cooker hood onto the wall bracket.
5) Open the glass panel, take out the grease filter, find the two positioning
holes inside the case in the figure, mark with pen respectively, and then
take down the cooker hood.
9
EN
Installation
6) Drill two 8mm holes in the marked position on the wall with an electric drill,
and then put the wall plug in.
7) Hang the cooker hood on the wall bracket again. After that, use two 4 *
30mm screws to lock the corresponding positioning in the figure.
8) The lower chimney bracket is used to fix the upper decorative chimney and
lower decorative chimney.
Use 2pcs ST4x8mm screws to attach lower and upper chimney together.
Before attaching the bracket to the chimney, decide the location of lower
chimney bracket fixing holes for fixing the lower chimney bracket in the
later step.
Do not fasten screws too much, make sure upper decorative chimney can
be telescopically adjusted after assembled.
10
EN
Installation
9) Put the Aluminum Flex Pipe on the air outlet of the cooker hood and fix the
tube with the Cable Ties.
10) Put the chimney on the cooker hood. Fix the lower chimney bracket on the
wall by 2 screws (4mm x30mm).
11
EN
Installation
11) Then pulling out the upper chimney upwards to the target height. Adjust to
reach the height required.
12) Fix the upper chimney on the upper chimney bracket by 2 screws (4x8mm).
Then fix the upper chimney bracket on the wall. Before fixing the bracket
on the wall, you can decide the upper chimney bracket fixing holes for
installation.
13) Fix the lower chimney with 2 pcs of ST4x8mm screws on the cooker hood.
NOTE:
Connect ductwork to hood and use metal foil duct tape to make joints
secure and air-tight.
Make sure the damper assembly (or round duct plate) enters the ductwork
and that the damper opens and closes freely.
12
EN
Installation
Activated Carbon Filter InstallationVENT INSIDE:
If you do not have an outlet to the outside, exhaust pipe is not required and the
installation is similar to the one shown in section “Installation (Vent outside)”
1. Activated carbon filter can be used to trap odors.
In order to install the activated carbon filter, the grease filter should be
detached first (The front panel opens at an Angle < 90°). Press the lock
and pull it downward.
2. Plug the activated carbon filter into the blower as shown and turn it in
anti-clockwise direction.
3. Install the grease filter. If replacement, please turn it in clockwise direction.
NOTE:
Make sure the filter is securely locked. Otherwise, it would loosen and
cause dangerous.
When activated carbon filter attached, the suction power will be lower.
The activated carbon filter should be changed every 3 months depending
on the conditions of us.
13
EN
Operation
Always turn your hood on before you begin cooking to establish an air
flow in the kitchen.
Electronic button
Operate the hood as follows:
STANDBY MODE
After plug in, When the buzzer makes a sound and all the indicator lights are
on for 1S then go out, the hood enters the standby mode. The [1] button
indicator light continues to flash regularly. If there is no operation for 60s, the
hood enters into sleep mode; If you need to operate, press any button briefly to
start up the cooker hood.
Press the [1] button for more than 1S, the hood will enter the working mode.
Press the corresponding function button to start the corresponding function
mode, and press again to turn off the corresponding function mode.
Low Speed button
It is suitable for simmering and cooking which do not make much steam.
Medium Speed button
Airflow speed is ideally for ventilation in standard cooking operation.
High Speed button
When high density of smoke or steam produced, press high-speed button for
highest effective ventilation.
Booster button
Depress this button to enter into highest speed.
Light button
When lights are OFF, push once on this button to turn ON the lights. Push this
button again to turn OFF the lights.
14
EN
Operation
The function of UV lamp
CAUTION:
1. UV lamp can not be touched by naked hands and can not be taken off.
2. When the front panel is open, UV lamp can not be turned on.
This appliance contains a UV emitter, Don't look straight at the light to
prevent eyes damage.
3. The UV lamp may start slowly in low temperature environment. Please wait
patiently. The lamp will return to normal operation after the temperature
rises.
UV lamp is mainly used for sterilization and disinfection. It is recommended to
turn on the UV lamp when the cooker hood is working (especially when using
the activated carbon internal circulation mode).
In the working mode, long press the [3] button and [B] button at the same time
to turn on UV lamp, and the light button indicator light starts to flash;
Long press the [3] button and [B] button at the same time to turn off the UV
lamp, and the light button indicator will stop flashing.
15
Smart Life APP
Download and Intallation of Smart Life APP
1. You must use Android phone or iPhone to download and use this APP.
2. Search “Smart Life” in the Googel Play store for Android or IOS App Store
to download and install the APP.
Cooker Hood and Smart Life APP pairing
1. When you log in to Smart Life APP for the first time, you need to create a
new account. When creating a new account, follow the app prompts to
register.
2. If you already have an account, you can use existing account to log in.
3. After logging in successfully, follow the steps below to connect the cooker
hood (the operating procedures of Android and IOS systems are the same)
Video Guide
EN
Operation
1. Open the smart life
app, Click Add Device.
2. Choose kitchen
appliances from the
menu bar on the left.
3. Choose kitchen hood.
4. Enter WiFi hotspot and
password, then click
Confirm.
5. When enter this
interface, choose AP
Mode on the top right
corner.
6. Click “Confirm the
indicator is blinking
slowly” and chick “Next”.
16
EN
Operation
7. After clicking “Reconnect”, long press the light key
for dialing on the display interface of the cooker hood.
The dialing process will flash for 2 minutes. If the
dialing is successful, smartlife-xxxx” will appear in
the WiFi setting of the mobile phone.
8. Access your phone's
WLAN Settings, Choose
SmartLife-xxxx and
connect.
9. After connecting to
SmartLife-xxxx, then
return to APP.
10. Connecting to WIFi
hotspot within 1minutes.
11. Displaying this
interface means
connecting successfully.
17
EN
Operation
12. Click “Done” shown as Step 11.
Return to the home interface. If kitchen
hood add in the list of “All Devices”, it
means connection is succeful.
13. Click "Kitchen Hood" enter the
operation interface.
About operation interface:
ON/Off Button
Light Button
When lights are OFF, push once on this button to turn ON the lights.
Push this button again to turn OFF the lights.
Fan Speed Button
You can control the corresponding gears of 1-2-3-P on the cooker hood.
When cooker hood working, could set delay function.
Push this button, the cooker hood will stop working in 5 minutes.
18
Purify ON/Off
Quick Delay Off
1/164