1
2
3
4
5
6
TE 700-AVR
en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 1
fr Moded'emploioriginal ............................... 14
es Manual de instrucciones original . . . . . . . . . . . . . . . . . . . . . . . 28
pt Manual de instruções original . . . . . . . . . . . . . . . . . . . . . . . . . . 44
*428076* 428076 English 1
Original operating instructions
1 Information about the operating instructions
1.1 About these operating instructions
• Read these operating instructions before the product is used or operated
for the first time. This is a prerequisite for safe, trouble-free handling and
use of the product.
• Observe the safety instructions and warnings in these operating instruc-
tions and on the product.
• Always keep the operating instructions with the product and make sure
that the product is accompanied by these operating instructions only,
when the product is given to other persons.
1.2 Explanation of symbols
1.2.1 Warnings
Warnings alert persons to hazards that occur when handling or using the
product. The following signal words are used:
DANGER
DANGER !
▶Draws attention to imminent danger that will lead to serious personal
injury or fatality.
WARNING
WARNING !
▶Draws attention to a potential threat of danger that can lead to serious
injury or fatality.
CAUTION
CAUTION !
▶Draws attention to a potentially dangerous situation that could lead to
personal injury or damage to the equipment or other property.
1.2.2 Symbols in the operating instructions
The following symbols are used in these operating instructions:
Comply with the operating instructions
Instructions for use and other useful information
Dealing with recyclable materials
Do not dispose of electric equipment and batteries as household
waste
Hilti Liion battery
2 English 428076 *428076*
Hilti charger
1.2.3 Symbols in illustrations
The following symbols are used in illustrations:
These numbers refer to the illustrations at the beginning of these
operating instructions.
The numbering reflects the sequence of operations shown in the
illustrations and may deviate from the steps described in the text.
Item reference numbers are used in the overview illustration and
refer to the numbers used in the key in the product overview sec-
tion.
These characters are intended to specifically draw your attention to
certain points when handling the product.
1.3 Symbols on the product
1.3.1 Symbols on the product
The following symbols are used on the product:
Chiseling
Chisel positioning
Protection class II (double-insulated)
Wear protective gloves
1.4 Product information
Hilti products are designed for professional use and may be operated,
serviced and maintained only by trained, authorized personnel. This
personnel must be specifically informed about the possible hazards. The
product and its ancillary equipment can present hazards if used incorrectly
by untrained personnel or if used not in accordance with the intended use.
The type designation and serial number are printed on the rating plate.
▶Write down the serial number in the table below. You will be required to
state the product details when contacting Hilti Service or your local Hilti
organization to inquire about the product.
Product information
Breaker TE 700AVR
Generation 01
Serial no.
*428076* 428076 English 3
2 Safety
2.1 General power tool safety warnings
WARNING Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow all instruc-
tions listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
Work area safety
▶Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
▶Do not operate power tools in explosive atmospheres, such as in
the presence of flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
▶Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
Electrical safety
▶Power tool plugs must match the outlet. Never modify the plug in
any way. Do not use any adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
▶Avoid body contact with earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators. There is an increased risk
of electric shock if your body is earthed or grounded.
▶Do not expose power tools to rain or wet conditions. Water entering
a power tool will increase the risk of electric shock.
▶Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase the risk
of electric shock.
▶When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
▶If operating a power tool in a damp location is unavoidable, use
a residual current device (RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
Personal safety
▶Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired
or under the influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in serious personal
injury.
4 English 428076 *428076*
▶Use personal protective equipment. Always wear eye protection.
Protective equipment such as a dust mask, non-skid safety shoes, hard
hat or hearing protection used for appropriate conditions will reduce
personal injuries.
▶Prevent unintentional starting. Ensure the switch is in the off-
position before connecting to power source and/or battery pack,
picking up or carrying the tool. Carrying power tools with your finger
on the switch or energising power tools that have the switch on invites
accidents.
▶Remove any adjusting key or wrench before turning the power tool
on. A wrench or a key left attached to a rotating part of the power tool
may result in personal injury.
▶Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
▶Dress properly. Do not wear loose clothing or jewellery. Keep your
hair and clothing away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
▶If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used.
Use of dust collection can reduce dust-related hazards.
▶Do not let familiarity gained from frequent use of tools allow you
to become complacent and ignore tool safety principles. A careless
action can cause severe injury within a fraction of a second.
Power tool use and care
▶Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at
the rate for which it was designed.
▶Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous
and must be repaired.
▶Disconnect the plug from the power source and/or remove the
battery pack, if detachable, from the power tool before making any
adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool
accidentally.
▶Store idle power tools out of the reach of children and do not
allow persons unfamiliar with the power tool or these instructions
to operate the power tool. Power tools are dangerous in the hands of
untrained users.
▶Maintain power tools and accessories. Check for misalignment or
binding of moving parts, breakage of parts and any other condition
that may affect the power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents are caused by poorly
maintained power tools.
*428076* 428076 English 5
▶Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
▶Use the power tool, accessories and tool bits etc. in accordance
with these instructions, taking into account the working conditions
and the work to be performed. Use of the power tool for operations
different from those intended could result in a hazardous situation.
▶Keep handles and grasping surfaces dry, clean and free from oil and
grease. Slippery handles and grasping surfaces do not allow for safe
handling and control of the tool in unexpected situations.
Service
▶Have your power tool serviced by a qualified repair person using
only identical replacement parts. This will ensure that the safety of the
power tool is maintained.
2.2 Hammer safety warnings
▶Wear ear protectors. Exposure to noise can cause hearing loss.
▶Use auxiliary handles, if supplied with the tool. Loss of control can
cause personal injury.
▶Hold power tool by insulated gripping surfaces, when performing an
operation where the cutting accessory may contact hidden wiring
or its own cord. Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give the operator
an electric shock.
2.3 Additional safety instructions for breakers
Personal safety
▶Use the product and accessories only when they are in perfect working
order.
▶Never tamper with or modify the product or accessories in any way.
▶When chiseling into ceilings, walls and floors, always make sure that you
have a safe and firm stance. A sudden break-through can affect your
balance!
▶Apply appropriate safety measures at the opposite side of the workpiece
in work that involves breaking through. Parts breaking away could fall
out and / or fall down causing injury to other persons.
▶You and the other persons in the vicinity must wear suitable eye
protection, a hard hat, ear protection, protective gloves and light
respiratory protection while the product is in use.
▶Wear protective gloves when changing the accessory tool. Touching the
accessory tool can result in cuts and burns.
▶Wear eye protection. Flying fragments can injure the body and eyes.
6 English 428076 *428076*
▶Dust produced by grinding, sanding, cutting and drilling can contain
dangerous chemicals. Some examples are: lead or lead-based paints;
brick, concrete and other masonry products, natural stone and other
products containing silicates; certain types of wood, such as oak,
beech and chemically treated wood; asbestos or materials that contain
asbestos. Determine the exposure of the operator and bystanders
by means of the hazard classification of the materials to be worked.
Implement the necessary measures to restrict exposure to a safe level,
for example by the use of a dust collection system or by the wearing
of suitable respiratory protection. The general measures for reducing
exposure include:
▶working in an area that is well ventilated,
▶avoidance of prolonged contact with dust,
▶directing dust away from the face and body,
▶wearing protective clothing and washing exposed areas of the skin
with water and soap.
▶Take frequent breaks and do physical exercises to improve the blood
circulation in your fingers. High vibration during long periods of work can
lead to disorders of the blood vessels and nervous system in the fingers,
hands and wrists.
Electrical safety
▶Before beginning work, check the working area for concealed electric
cables or gas and water pipes. External metal parts of the product could
give you an electric shock or cause an explosion if you accidentally
damage an electric cable or a gas or water pipe.
Power tool use and care
▶Wait until the product has come to a complete stop before you lay it
down.
3 Description
3.1 Overview of the product 1
@Chuck
;Function selector switch
=Power level selection switch
%On/off switch
&Grip
(Indicators
)Supply cord
+Air vents
§Knob
/Side handle
:Theft protection indicator (op-
tional)
∙Service indicator
$Power level indicator
*428076* 428076 English 7
3.2 Intended use
The product described is an electrically powered breaker for medium-duty
chiseling work. It is designed for removing and breaking up concrete,
masonry and stone.
▶Operation is permissible only when connected to a power source
providing a voltage and frequency in compliance with the information
given on the type identification plate.
3.3 Active Vibration Reduction (AVR)
The breaker is equipped with an Active Vibration Reduction (AVR) system,
which reduces vibration significantly.
3.4 Service indicator
The breaker is equipped with a service indicator LED.
Status Meaning
The service indicator lights red. End of service interval – servicing is
due.
A fault has occurred in the tool.
The service indicator blinks red. The overheating prevention cut-out
has been activated.
The voltage provided by the electric
supply is too high.
Bring the product to Hilti Service in good time. This will help to ensure
that it’s always ready for use.
3.5 Power level indicator
The breaker is equipped with a power level indicator LED.
Chiseling power can be reduced to approx. 70% by pressing the power
level selector switch. The power level LED then lights up, indicating reduced
power.
3.6 Restart interlock
The tool doesn’t restart automatically when the power returns after an
interruption in the supply. The on/off switch must first be released and then
pressed again to restart.
3.7 Items supplied
Breaker, side handle, operating instructions.
You can find other system products approved for your product at your
local Hilti Center or online at: www.hilti.com
8 English 428076 *428076*
4 Technical data
4.1 Breaker
For details of the rated voltage, frequency, current and input power,
please refer to the power tool’s country-specific type identification plate.
When powered by a generator or transformer, the generator or transformer’s
power output must be at least twice the rated input power shown on the rating
plate of the power tool. The operating voltage of the transformer or generator
must always be within +5% and -15% of the rated voltage of the power tool.
Single impact energy 11.5 J
Weight 17.4 lb
(7.9 kg)
5 Operation
5.1 Preparations at the workplace
CAUTION
Risk of injury! Inadvertent starting of the product.
▶Unplug the supply cord before making adjustments to the power tool or
before changing accessories.
Observe the safety instructions and warnings in this documentation and on
the product.
5.2 Fitting the side handle 2
CAUTION
Risk of injury! Loss of control over the breaker.
▶Check that the side handle is fitted correctly and tightened securely.
1. Slide the side handle clamping band over the tool holder from the front
and into the recess provided.
2. Bring the side handle into the desired position.
3. Secure the side handle by turning the knob until the clamping band is
tight.
5.3 Fitting the accessory tool 3
WARNING
Risk of injury! The accessory tool gets hot during use and may also have
sharp edges.
▶Wear protective gloves when changing the tool.
*428076* 428076 English 9
DANGER
Risk of fire! Risk of contact between the hot accessory tool and highly
inflammable materials.
▶Do not lay the hot accessory tool down on highly inflammable materials.
Check the accessory tool for damage or uneven wear each time before
use and replace it if necessary.
Use only the recommended grease supplied by Hilti. Use of unsuitable
grease may cause damage to the product.
1. Apply a little grease to the connection end of the accessory tool.
2. Push the accessory tool into the chuck as far as it will go, turning it and
applying light pressure until it engages with an audible click.
▶The product is ready for use.
Use only the recommended grease supplied by Hilti. Use of
unsuitable grease may cause damage to the product.
5.4 Removing the accessory tool 4
DANGER
Risk of fire! Risk of contact between the hot accessory tool and highly
inflammable materials.
▶Do not lay the hot accessory tool down on highly inflammable materials.
WARNING
Risk of injury! The tool becomes hot as a result of use.
▶Wear protective gloves when changing the tool.
1. Pull the chuck back.
2. Remove the accessory tool.
Use only the recommended grease supplied by Hilti. Use of
unsuitable grease may cause damage to the product.
5.5 Positioning the chisel 5
The chisel can be adjusted to 24 different positions (in 15° increments).
This ensures that flat chisels and shaped chisels can always be set to
the optimum working position.
▶Set the function selector switch to and position the chisel as desired.
10 English 428076 *428076*
5.6 Locking the chisel
▶Set the function selector switch to and rotate the chisel until it
engages.
5.7 Setting the chiseling power
Chiseling power can be reduced to approx. 70% by pressing the power
level selector switch. The power level LED then lights up, indicating
reduced power.
Chiseling power can be adjusted only when the power tool is switched
on and ready for use. To reselect full chiseling power, press the chiseling
power level selector switch again. Switching off and then on again also
causes the power tool to return to full chiseling power.
▶Press the power level selector switch.
6 Types of work
WARNING
Risk of electric shock! Severe injury and burns can result if any attempt
is made to operate the tool without an earth/ground conductor and ground
fault circuit interrupter correctly connected.
▶Irrespective of whether mains power or generator power is used, always
make sure that an earth/ground conductor and ground fault circuit
interrupter are present in the power supply and that these are correctly
connected.
▶Do not use the product unless these safety measures are in place and
fully operational.
WARNING
A damaged supply cord presents a hazard! Do not touch the supply cord
or extension cord if damaged while working. Disconnect the supply cord
plug from the power outlet.
▶Check the appliance’s supply cord at regular intervals and have it
replaced by a qualified specialist if found to be damaged.
Full approval must be obtained from the site engineer or architect prior to
beginning the work.
6.1 Chiseling 6
▶Set the function selector switch to the position.
*428076* 428076 English 11
7 Care and maintenance
WARNING
Electric shock hazard! Attempting care and maintenance with the supply
cord connected to a power outlet can lead to severe injury and burns.
▶Always unplug the supply cord before carrying out care and maintenance
tasks.
Care
• Carefully remove stubborn dirt from the tool.
• Clean the air vents carefully with a dry brush.
• Use only a slightly damp cloth to clean the casing. Do not use cleaning
agents containing silicone as they can attack the plastic parts.
Maintenance
WARNING
Danger of electric shock! Improper repairs to electrical components may
lead to serious injuries including burns.
▶Repairs to the electrical section of the tool or appliance may be carried
out only by trained electrical specialists.
• Check all visible parts and controls for signs of damage at regular
intervals and make sure that they all function correctly.
• Do not operate the product if signs of damage are found or if parts
malfunction. Have it repaired immediately by Hilti Service.
• After cleaning and maintenance, fit all guards or protective devices and
check that they function correctly.
To help ensure safe and reliable operation, use only genuine Hilti spare
parts and consumables. Spare parts, consumables and accessories
approved by Hilti for use with the product can be found at your local
Hilti Store or online at: www.hilti.group.
7.1 Cleaning the dust shield
▶Clean the dust shield on the chuck with a dry, clean cloth at regular
intervals.
▶Clean the sealing lip by wiping it carefully and then grease it again lightly
with Hilti grease.
▶It is essential that the dust shield is replaced if the sealing lip is damaged.
8 Transport and storage
• Do not transport electric tools with accessory tools fitted.
• Always unplug the supply cord before storing an electric tool or appliance.
• Store tools and appliances in a dry place where they cannot be accessed
by children or unauthorized persons.
12 English 428076 *428076*
• Check electric tools or appliances for damage after long periods of
transport or storage.
9 Troubleshooting
If the trouble you are experiencing is not listed in this table or you are unable
to remedy the problem by yourself, please contact Hilti Service.
9.1 Troubleshooting
Trouble or fault Possible cause Action to be taken
The breaker doesn’t
start.
Electronics initialization
in progress (takes up to
4 seconds after plugging
in).
▶Switch the power tool
off and then on again.
The electronic restart
interlock is activated
after an interruption in
the electric supply.
▶Switch the power tool
off and then on again.
Interruption in the elec-
tric supply.
▶Plug in another electric
tool or appliance
and check whether it
works.
The generator is in sleep
mode.
▶Apply a load to
the generator by
connecting a second
power consumer (e.g.
worklight). Switch the
tool off and then on
again.
The tool is faulty or ser-
vicing is due.
▶Have the product
repaired only by Hilti
Service.
No hammering ac-
tion.
The power tool is too
cold.
▶Bring the tip of the
accessory tool into
contact with the
working surface,
switch the power
tool on and allow it
to run. If necessary,
repeat the procedure
until the hammering
mechanism begins to
operate.
*428076* 428076 English 13
Trouble or fault Possible cause Action to be taken
No hammering ac-
tion.
Chuck not sufficiently
greased.
▶Inject 1-2 strokes
of grease from the
dispenser into the
chuck. Use genuine
Hilti grease. Then fit
the accessory tool and
distribute the grease
in the chuck by pulling
the accessory tool in
and out several times.
The service indicator
lights red.
The tool is faulty or ser-
vicing is due.
▶Have the product
repaired only by Hilti
Service.
The service indicator
blinks red.
The overheating preven-
tion cut-out has been
activated.
▶Allow the tool to cool
down. Clean the
air vents. Running
under no load is still
possible.
The voltage provided by
the electric supply is too
high.
▶Use a different power
outlet. Check the
electric supply.
The breaker
switches itself off
while running.
The overheating preven-
tion cut-out has been
activated.
▶Allow the tool to cool
down. Clean the
air vents. Running
under no load is still
possible.
The breaker doesn’t
achieve full power.
Power reduction is ac-
tive.
▶Press the power level
selector switch (ob-
serve the power level
indicator). Unplug the
power tool from the
electric supply and
then plug it back in.
The extension cord is
too long or its gauge is
inadequate.
▶Use an extension cord
of an approved length
and / or of adequate
gauge.
The voltage provided by
the electric supply is too
low.
▶Connect the power
tool to a different
power source.
14 Français 428076 *428076*
Trouble or fault Possible cause Action to be taken
The chisel cannot
be released from the
chuck.
The chuck is not pulled
back fully.
▶Pull the tool lock back
as far as it will go and
remove the insert tool.
10 Disposal
Most of the materials from which Hilti tools and appliances are manu-
factured can be recycled. The materials must be correctly separated before
they can be recycled. In many countries, your old tools, machines or appli-
ances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti
representative for further information.
▶Do not dispose of power tools, electronic equipment or batteries as
household waste!
11 Manufacturer’s warranty
▶Please contact your local Hilti representative if you have questions about
the warranty conditions.
Mode d'emploi original
1 Indications relatives au mode d'emploi
1.1 À propos de ce mode d'emploi
• Avant de mettre l'appareil en marche, lire impérativement ce mode
d'emploi. C'est la condition préalablement requise pour assurer la
sécurité du travail et un maniement sans perturbations.
• Bien respecter les consignes de sécurité et les avertissements du présent
mode d'emploi ainsi que celles figurant sur le produit.
• Toujours conserver le mode d'emploi à proximité du produit et uni-
quement transmettre le produit à des tiers accompagné de ce mode
d'emploi.
1.2 Explication des symboles
1.2.1 Avertissements
Les avertissements attirent l'attention sur des dangers liés à l'utilisation du
produit. Les termes de signalisation suivants sont utilisés :
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
dans d''autres langues
- English: Hilti 700-AVR User manual
- español: Hilti 700-AVR Manual de usuario
- português: Hilti 700-AVR Manual do usuário
Documents connexes
-
Hilti 428944 Mode d'emploi
-
Hilti TE 800 Manuel utilisateur
-
-
Hilti TE 1000-AVR Mode d'emploi
-
-
-
-
Hilti TE 500 Mode d'emploi
-
-