Legrand LMDL-600 Guide d'installation

Marque: Legrand

Modèle: LMDL-600

Taper: Guide d'installation

Wattstopper

DLM Wireless Photosensor with IPv6/Bluetooth

Low Energy Technology

Installation Instructions • Instructions d’Installation • Instrucciones de Instalación

No: 27365 – 03/20 rev.5

Catalog Number • Numéro de Catalogue • Número de Catálogo: LMDL-600

Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China

SPECIFICATIONS

Light sensor range ..................................................................... 1 to 1,500 fc

Power Supply ............................. Battery powered, CR123A Lithium Ion, 3 VDC

Connection to DLM Network .... Wireless via LMRC-611 series room controllers

Wireless Radio ...........................................Single, Concurrent 802.15.4 and

...................................................... Bluetooth Low Energy, 2.4GHz

Wireless Communication

IPv6 Mesh (6LoWPAN) Range .............................................. up to 60 ft.

Bluetooth low energy Range .................................................up to 30 ft.

60 ft. max. between LMDL-600 and room controller

Wireless Encryption ............................................ AES-128 bit symmetric key

Environment:

Operating Temperature ........................................32° to 104°F (0° to 40°C)

Storage Temperature ......................................... 23° to 140°F (-5° to 60°C)

Relative Humidity ..............................................5 to 95% (non condensing)

Other:

Plenum Rating ................................................................................... UL2043

Compliance/Regulatory

FCC, RoHS, Bluetooth, IC certified

UL and cUL listed (E101196)

Patent Pending

UNIT DESCRIPTION

The DLM Wireless photo sensor is a wireless battery

powered light sensor intended for operation with Wireless

room controllers. It is an open loop photo sensor that

measures daylight in foot candles to automatically switch or

dim zones of lighting. The sensor sends light level signals

to LMRC-611 room controllers to adjust connected lighting

loads.

Sensor Installation and Conguration Overview

1. Mount the photosensor so that the Daylight Viewing

Port directly views the daylight entering the space

through a window or a skylight. See Placement

Guidelines and Mounting the Photosensor.

2. Turn ON power to the room controller.

3. Use LMCS-100 or the DLM Configuration App software

to complete the configuration process. The LMDL-600

will not operate properly until the configuration and

calibration is successful.

4. Ensure there is a minimum 5fc of ambient light in the

space.

5. From LMCS or the App, select the room network

you’d like to calibrate and select the LMDL to start the

calibration process. You will need a light level meter in

order to record the fc data of the space for each prompt

in the software. Place the light meter at the task level.

6. After following the software prompts, once calibrated,

you can adjust switch overrides and other features by

selecting the LMRC that the LMDL is paired to.

Application Note: Depending on external factors (such as

environment, fixture location and dimming curve of the load)

an adjustment factor may be needed to achieve the target

light level after calibration. If the calibrated LMDL and fixture

combination outputs less light than the target light level

(set in the LMRC parameter), adjust the ‘target light level’

parameter by increasing to an appropriate amount.

IMPORTANT: You must wake the device (press the Config

button) before commissioning. If the LMDL is paired to a

room with LMCS, LMCS is required to calibrate the sensor.

If the LMDL is paired to a room with the DLM Configuration

App, please calibrate with the DLM Configuration App.

Sensor Params

LMPX-600

LMPC-600

Mode Auto On

Blink On

Load Type Dim

LMBR-650

For networking

and managing

rooms, floors,

and building

(optional

)

LMRC-61

1MCC

Wireless

Dimmer and/or

Scene Switch

LMDL-600

Wireless

Photosensor

IPv6 Mesh for

networking of DLM

rooms and devices

over 6LoWPAN

Bluetooth low energy

communication for

mobile App suppor

DLM Configuration App

on a mobile device

WIRELESS DLM CONNECTION

NOTE: The LMDL cannot be

used in a Hybrid DLM Room.

The LMDL must be used with

wireless room controllers.

Distance Recommendations:

30’ max between LMDL-600 and mobile device

60’ max. between LMDL-600 and room controller or bridge

10’ minimum and 100’ maximum between LMBR-650 and room

controller

The LMDL-600 switches or dims electric light in response to daylight. It is important to select a location where the photosensor

measures daylight contribution only. For proper operation the photosensor should not see any electric light contribution.

When the primary source of daylight is a window (sidelighting), the LMDL-600 is typically ceiling mounted between one to three feet

away from the window. The figure below shows a typical placement location for a sidelit application.

WARNING: DO NOT USE THE DLM LOCAL NETWORK TO CONTROL LOADS OTHER THAN LIGHTING IF THE

LOAD IS NOT IN VIEW OF A PERSON AT ALL CONTROL LOCATIONS. DO NOT USE DLM TO CONTROL ANY

LOAD THAT MIGHT BE DANGEROUS OR CAUSE A HAZARDOUS SITUATION IF ACCIDENTALLY ACTIVATED.

PLACEMENT GUIDELINES

60°

Mount photosensor close to window

to see only daylight contribution.

Sensor must not view

electric light output.

LMDL-600

45°

Window

Light Fixture

IMPORTANT INSTALLATION INFORMATION

To ensure a successful installation and startup of a wireless system, the following steps must be taken by the

installing contractor. Failure to document all device address and locations may delay completion of startup

and result in additional startup charges.

Key Requirement: Document every Device’s MAC Address (at least the last 4 alphanumeric characters). An

additional MAC address label is included for the installer to use on a floor plan map. The last four characters are

repeated in a larger font, in bold. Keep this document so that the commissioning tech has access at a later date.

MOUNTING THE PHOTOSENSOR

The LMDL-600 in a ceiling or open ceiling environment so that the daylight view port directly views daylight entering the space through a

window or skylight.

NOTE: The LMDL-600 operates on an included CR123A battery. Before mounting, pull the battery tab on the back of the unit to activate

the battery and power the unit.

The photosensor can be mounted using one of thee possible methods:

• Mounted to the ceiling using the included plastic mounting plate

• Mounted to a hanging threaded rod, for open ceiling environments, using the included threaded rod adapter

• Recessed mounting, using the optional LMDL-600-RPM Recessed Plenum Mounting Kit

NOTE: The LMDL-600 has a rotating cover which allows the daylight port to be adjusted to point directly at the window or skylight. The

cover can be rotated approximately 170°, so mount the photosensor so it points in the general direction of the window/skylight

and then adjust the cover.

Twist to

Lock

Ceiling Mount

1. Attach the mounting plate to the ceiling with the

three included 1” mounting screws.

2. Twist the LMDL-600 clockwise to lock it onto

the mounting plate.

Light Fixture

Skylight

LMDL-600

60°

NOTE: Pull protective battery tab

before installation to power

the sensor.

Pull Tab

Rotate sensor window

so that it points towards

window or skylight

Examples of labels

Twist to

Lock

Mounting Bracket

Threaded hole - 3/8"-16

Threaded hole - 1/4"-20

Threaded Rod Size

3/8"-16, 1/4"-20,

or 1/2”-13

Threaded hole - 1/2"-13

Threaded Rod Mount

The threaded rod adapter can mount to a 3/8” - 16 or

1/4” - 20 hanging threaded rod.

1. Screw the adapter onto the rod.

2. Attach the mounting plate to the adapter using

the included 10mm screw.

3. Twist the LMDL-600 clockwise to lock it onto

the mounting plate.

SETTING UP A ROOM NETWORK BY PAIRING DEVICES

Pair wireless devices to a room controller to create an individual room network and enable Plug N’ Go operation.

Device pairing can be done by using by using the DLM Config App or Push-to-Pair (PtP) mode on the room controller and all other

wireless devices. Because the app is needed for commissioning the LMDL-600, you may find it easier to use the DLM Config app.

To pair devices in a network, they must all have the same wireless channel and Network ID. By default the channel is 15 and the

Network ID is 1. Using Push-to-Pair mode, the Network ID for all devices being paired is migrated to a new number, so that only those

device communicate with each other. The channel number will remain at 15.

NOTE: LMCS-100 software, version 4.7 or later can also be used to pair devices. However, LMCS-100 requires use of an LMBR-650.

Using LMCS, it is possible to change the channel as well as Network ID.

DEVICE PAIRING, COMMISSIONING, AND UNIT ADJUSTMENT USING THE DLM CONFIG APP

The DLM Config App is available for both iOS® and Android® devices. Search “DLM Config” on your device to download.

The app provides the ability to pair various devices in a room. The app is also required in order to configure and calibrate the LMDL-

600, which must be done before it will function correctly in the room. Additionally, you can modify load binding and edit various DLM

parameters within the app.

For details on the features and operation, download the DLM Config App User Guide from the

wattstopper web site at :

https://www.legrand.us/wattstopper.aspx

NOTE: LMCS-100 software, version 4.7 or later can also be used to pair devices, commission the LMDL-600, and edit DLM

parameters. However, LMCS-100 requires use of an LMBR-650.

Twist to

Lock

Spring

Arm

Cut hole with 3 1/8” hole saw

Twist to

Lock

Spring

Arm

Cut hole with 3 1/8” hole saw

Recessed Mount, using the LMDL-600-RPM

1. Using a 3 1/8” hole saw, cut a hole in the ceiling.

2. Raise the spring loaded arms so they fit through the hole.

3. Release the arms. The LMDL-600 will loosely clamp to the ceiling.

4. Hold the edges of the recessed mounting plate to prevent it from

moving, then twist the LMDL-600 clockwise to lock it onto the mounting

plate.

12 Gauge

Wire Hanger

Hanger attachment

feature, for use when

local safety or seismic

requirements are

applicable.

Note: Once the

sensor is attached

to the recessed

mount, the sensor

will be firmly

in place.

DEVICE PAIRING USING PUSH-TO-PAIR MODE

Push-to-Pair in a room with a single LMRC-611 Room Controller

NOTE: Once you enter PtP mode on the room controller, a three minute timer begins. If the

Config button on any device in the room is pressed, the timer resets and begins the

three minute countdown again. If no Config button is pressed within three minutes, the

room controller will exit PtP mode.

1. Enter PtP mode on the room controller. Press the Config button three times (within

three seconds) until the LED on the room controller flashes green.

2. Enter PtP mode on the LMDL-600. Using a pointed tool, press the Config button three

times. As with the room controller, the LED on the switch will flash green.

3. Pair the LMDL-600. Press the Config button on the LMDL-600 one more time to pair it to

the room controller. The load connected to the room controller will toggle once (if the load is OFF, it will turn ON; if ON, it will turn

OFF) to indicate that pairing was successful. Also, the LMDM-601’s blinking LED will turn to solid green as another indicator of a

successful pairing.

NOTE: If there are any wireless sensors, dimmers, or additional switches in the room, repeat steps 2 and 3 for each of those

devices so that all devices are paired together in the same network. For each device, the load will toggle during step 3.

4. Exit PtP mode. From any device, press the Config button 3 times. After a few seconds, the LED on each Room controller, switch

or sensor currently in PtP mode will flash white and reboot, leaving the default network and migrating to the new network. Then,

the LED on the room controller will flash blue and the pairing process finishes.The default Network ID on all devices will change to

a new number, based on the last four digits of the Mac address on the room controller, and now those devices will communicate

only with each other and not any devices which have not been paired.

NOTE: It is important to exit PtP mode within the three minute time limit mentioned above. If you do not, none of the device

pairings will be remembered and you have to start the process over from the beginning.

Push-to-Pair in a room with multiple LMRC-611s

In a room with multiple loads, there may be more than one LMRC-611. They can all be paired to the same room network, allowing the

scene switch to set each load to different levels per scene. One of the room controllers will become the master, determining the Network

ID and channel settings for all the devices in the network.

1. Enter wireless Push-to-Pair (PtP) mode on all room controllers. Press the Config button three times on each LMRC-611 to put them

all in PtP mode. The green LEDs will flash on all room controllers. The first room controller placed into PtP will become the master.

2. Pair the room controllers together. Press the Config button one more time on each room controller except for the master. This

indicates to the rooms controllers that they will be paired with each other.

The master room controller’s LED blink rate will double once the first device is paired to it. This faster blink rate is convenient when

multiple room controllers are present on the same network.The LED will turn solid on the other controllers being paired.

NOTE: If there are more than two room controllers, you have the choice of either placing them all in PtP mode and then pairing

them, or pairing the first two controllers and then repeating steps 1 and 2 for each additional controller, leaving the master

controller in PtP mode the entire time.

3. Enter PtP mode on the LMDL-600. Press the Config button three times. As with the room controller, the LED on the switch will

flash green. Also, the LMDM-601’s blinking LED will turn to solid green as another indicator of a successful pairing.

4. Pair the LMDL-600. Press the Config button on the LMDL-600 one more time to pair it to the room controller. The load connected

to the room controller will toggle once (if the load is OFF, it will turn ON; if ON, it will turn OFF) to indicate that pairing was

successful.

NOTE: If there are any wireless sensors, dimmers, or additional switches in the room, repeat steps 2 and 3 for each of those

devices so that all devices are paired together in the same network. For each device, the load will toggle during step 3.

5. Exit PtP mode. From any device, press the Config button 3 times. After a few seconds, the LED on each Room controller, switch

or sensor currently in PtP mode will flash white and reboot, leaving the default network and migrating to the new network. Then,

the LED on the room controller will flash blue and the pairing process finishes.The default Network ID on all devices will change

to a new number, based on the last four digits of the Mac address on the master room controller, and now those devices will

communicate only with each other and not any devices which have not been paired.

NOTE: It is important to exit PtP mode within the three minute time limit mentioned above. If you do not, none of the device

pairings will be remembered and you have to start the process over from the beginning.

Pairing a device to an existing network

If you need to add the LMDL-600 to an existing in room network, follow the procedure below:

1. Enter wireless Push-to-Pair (PtP) mode on the room controller or any currently paired battery device. Press the Config

button three times (within three seconds).The LED on the room controller and any paired battery devices that are currently awake

will flash green.

2. Enter PtP mode on the LMDL-600. Using a pointed tool, press the Config button three times. As with the room controller, the LED

on the switch will flash green.

3. Pair the devices. Press the Config button on the LMDL-600 one more time to pair the LMDL-600 to the room controller. The load

connected to the room controller will toggle once (if the load is OFF, it will turn ON; if ON, it will turn OFF) to indicate that pairing

was successful.

Press here

to pair with

room controller

4. From any device, press the Config button 3 times. After a few seconds, the LED on the LMDM-601 will flash white and reboot,

leaving the default network and migrating to the new network. Then the LED on the room controller will flash blue while it

completes the pairing process. The Network ID of the LMDL-600 will change to the value used by the previously paired devices

and the room controller also returns to that value.

RESETTING THE LMDL-600

When you reset the LMDL-600, the Channel and Network ID will return to their default values, and if the switch was previously paired, it

will no longer be connected to that room network. All DLM parameters are also returned to their default values.

There are two ways to reset the LMDL-600:

• Press the Config button 10 times. The LED will blink green each time the Config button is

pressed. After the 10th press, the LED will turn red then briefly turn white indicating it is

rebooting.

• On the back of the sensor, is a small hole that will fit a paper clip. Use a paper clip to depress

the button inside that hole and hold for 10 seconds. When you first press the reset button, the

LED will blink red once, then after the 10 second will reboot and the LED will briefly turn white,

indicating it is rebooting.

NOTE: You can also reset the LMDL-600 from the DLM Config App or LMCS (the LMDL-600 must be

woken up before resetting).

LED INDICATORS

LED Color Function

White Unit Boot Up

Green, 1 Blink Config Button Pressed

Blinking Green Push to Pair Mode

Red, 1 Blink Indicates low battery. It will only blink if the Config button is pressed.

Also blinks if Reset button on back is pressed

Blinking Red Push n’ Learn Mode (not applicable to LMDL-600 but will blink if other devices are in PnL)

Paper Clip

Reset Hole

800.879.8585

www.legrand.us/wattstopper

No. 27365 – 03/20 rev. 5

Wattstopper warranties its products to be free

of defects in materials and workmanship for a

period of five (5) years. There are no obligations

or liabilities on the part of Wattstopper for

consequential damages arising out of, or in

connection with, the use or performance of this

product or other indirect damages with respect

to loss of property, revenue or profit, or cost of

removal, installation or reinstallation.

Wattstopper garantit que ses produits sont

exempts de défauts de matériaux et de fabrication

pour une période de cinq (5) ans. Wattstopper

ne peut être tenu responsable de tout dommage

consécutif causé par ou lié à l’utilisation ou

à la performance de ce produit ou tout autre

dommage indirect lié à la perte de propriété, de

revenus, ou de profits, ou aux coûts d’enlèvement,

d’installation ou de réinstallation.

Wattstopper garantiza que sus productos

están libres de defectos en materiales y mano

de obra por un período de cinco (5) años. No

existen obligaciones ni responsabilidades por

parte de Wattstopper por daños consecuentes

que se deriven o estén relacionados con el

uso o el rendimiento de este producto u otros

daños indirectos con respecto a la pérdida

de propiedad, renta o ganancias, o al costo

de extracción, instalación o reinstalación.

WARRANTY INFORMATION INFORMATIONS RELATIVES À LA GARANTIE INFORMACIÓN DE LA GARANTÍA

FCC REGULATORY STATEMENTS

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

This device complies with FCC and IC safety levels of radio frequency (RF) exposure for Mobile devices.

This device is only authorized for use in a mobile application. At least 20 cm of separation distance between this device and the user’s body must be

maintained at all times.

Any changes or modifications not expressly approved by The Watt Stopper Inc. could void the user’s authority to operate the equipment.

DÉCLARATION FCC

Ce dispositif est conforme à la section 15 des règlements de la FCC. On peut s’en servir sous réserve des deux conditiond suivantes.

1)Ce dispositif ne provoque pas d’interférences nuisibles; 2) Il doit être en mesure d’accepter toute interférence reçue, y compris les interférences qui

peuvent causer un fonctionnement indésirable.

REMARQUE: Ce matériel a été mis à l’essai et a été jugé conforme aux limites d’un dispositif numérique de classe A, conformément à la section

15 des règlements de la FCC. Ces limites visent à offrir une protection raisonnable contre les interférences nuisibles dans un

environnement commercial. Ce matériel génère, utilise et peut émettre des radiofréquences et, s’il n’est pas installé ou utilisé

conformément aux directives, peut causer des interférences nuisibles aux communications radio. L’utilisation de cet équipement

dans une zone résidentielle est susceptible de provoquer des interférences nuisibles, dans un tel cas l’utilisateur devra corriger les

interférences à ses frais.

Cet appareil est conforme aux niveaux de sécurité FCC et IC de l’exposition aux radiofréquences (RF) pour les appareils mobiles.

Cet appareil n’est autorisé que pour une application mobile. Au moins 20 cm de distance de séparation entre cet appareil et le corps de l’utilisateur

doivent être maintenu en tout temps.

Tout changement ou modification non expressément approuvé par The Watt Stopper Inc. pourrait annuler le droit de l’utilisateur à utiliser l’équipement

The Bluetooth® word mark and logos are registered trademarks owned by the

Bluetooth SIG, Inc. and any use of such marks by Wattstopper is under license.

Google Play and the Google Play

logo are trademarks of Google Inc.

The Apple logo, iPhone, iPod touch, and iTunes are trademarks

of Apple Inc., registered in the U.S. and other countries.