Wacker Neuson VP1030A Manuel utilisateur

Operator's manual

Vibratory plate

WP, VP

Model WP, VP

Document 5100027606

Issue 10.2015

Version 01

Language en

100_0000_0001.fm 2

Manufacturer

Wacker Neuson Produktion GmbH & Co. KG

Preussenstrasse 41

80809 Munich

www.wackerneuson.com

Tel.: +49-(0)89-354 02-0

Fax: +49-(0)89-354 02-390

Original operator's manual

Table of contents

5100021600IVZ.fm 3

1 Preface ....................................................................................................................................5

2 Introduction ............................................................................................................................6

2.1 Using the manual......................................................................................................................... 6

2.2 Storage location of the manual .................................................................................................... 6

2.3 Accident prevention regulations................................................................................................... 6

2.4 More information.......................................................................................................................... 6

2.5 Target group ................................................................................................................................ 6

2.6 Explanation of symbols................................................................................................................ 6

2.7 Wacker Neuson Contact partner ................................................................................................. 7

2.8 Disclaimer.................................................................................................................................... 7

2.9 Product identification of the machine........................................................................................... 7

3 Safety ......................................................................................................................................8

3.1 Policy ........................................................................................................................................... 8

3.2 Areas of responsibility of the operator ......................................................................................... 9

3.3 Operator responsibilities.............................................................................................................. 9

3.4 Personnel qualification................................................................................................................. 9

3.5 General sources of danger .......................................................................................................... 9

3.6 General safety instructions .......................................................................................................... 9

3.7 Specific safety instructions – Vibratory plates ........................................................................... 10

3.8 General safety instructions - Combustion engines .................................................................... 11

3.9 General safety instructions – fuel, lubricants and coolants........................................................ 11

3.10 Maintenance .............................................................................................................................. 12

3.11 Personal Protective Equipment ................................................................................................. 12

3.12 Safety devices ........................................................................................................................... 13

3.13 Behavior in dangerous situations............................................................................................... 13

4 Safety and information labels ............................................................................................14

5 Setup and function ..............................................................................................................16

5.1 Standard package ..................................................................................................................... 16

5.2 Application areas ....................................................................................................................... 16

5.3 Short description........................................................................................................................ 16

5.4 Versions..................................................................................................................................... 16

6 Components and operator's controls ................................................................................17

6.1 Components .............................................................................................................................. 17

6.2 Operator's controls .................................................................................................................... 17

7 Transport ..............................................................................................................................18

7.1 Loading and transport................................................................................................................ 18

8 Operation and use ...............................................................................................................20

8.1 Initial operation .......................................................................................................................... 20

8.2 Before commissioning ............................................................................................................... 20

8.3 Notes about operation ............................................................................................................... 20

8.4 Commissioning .......................................................................................................................... 21

8.5 Operation................................................................................................................................... 22

8.6 Decommissioning ...................................................................................................................... 22

9 Maintenance .........................................................................................................................23

9.1 Maintenance table ..................................................................................................................... 24

9.2 Maintenance jobs....................................................................................................................... 24

10 Troubleshooting ..................................................................................................................31

10.1 Fault table.................................................................................................................................. 31

Inhalt

Table of contents

4 5100021600IVZ.fm

11 Accessories ......................................................................................................................... 32

12 Technical data ..................................................................................................................... 33

12.1 WP1540 ..................................................................................................................................... 33

12.2 WP1550 ..................................................................................................................................... 34

12.3 Combustion engine.................................................................................................................... 35

EC declaration of conformity .....................................................................................36

DIN EN ISO 9001 certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

1 Preface

100_0000_0002.fm 5

1 Preface

This operator's manual contains information and procedures for the safe operation and safe

maintenance of your Wacker Neuson machine. For your own safety and to protect against injuries, you

must read the safety instructions carefully, familiarize yourself with them and observe them at all times.

This operator's manual is not a manual for extensive maintenance or repair work. Such work should be

carried out by Wacker Neuson service or by technically trained personnel.

When building this machine, great value was placed on the safety of its operator. However, an improper

operation or improper maintenance can pose dangers. Please operate and maintain your

Wacker Neuson machine in accordance with the information in this operator's manual. Your attention will

be rewarded with trouble-free service and a high level of availability.

Defective machine parts must be exchanged immediately!

Please contact your Wacker Neuson contact partner for questions regarding the operation or

maintenance.

All rights are reserved, in particular the right of duplication and distribution.

This operator's manual — even in part — may only be reproduced, used, copied or distributed with the

express, prior written consent from Wacker Neuson .

Any type of reproduction, distribution or storage on data carriers in any form or type that is not approved

by Wacker Neuson represents a violation of the valid copyright and you will be prosecuted.

We reserve the express right to technical modifications that are used to improve our machines or to raise

the safety standard, even without special notice.

2 Introduction

100_0000_0013.fm 6

2 Introduction

2.1 Using the manual

This manual is to be considered part of the machine and should be carefully stored during the entire

service life of the machine. This manual shall be transferred to subsequent owners or users of the

machine.

2.2 Storage location of the manual

This manual is part of the machine and must be kept in the immediate vicinity of the machine and made

accessible to staff at all times.

If this manual is lost, or if a second copy is required, there are two options to obtain a replacement:

 Download from the Internet www.wackerneuson.com

 Contact your Wacker Neuson contact partner.

2.3 Accident prevention regulations

In addition to the notes and safety instructions in this manual, the local accident prevention regulations

as well as the national health and safety regulations apply.

2.4 More information

This manual applies to various machine types from one product series. For this reason, some figures

may vary slightly in appearance from the machine purchased. Depending on the model, there may be

descriptions of components that are not included in the standard package.

The information contained in this manual is based on machines manufactured up to the time of printing.

Wacker Neuson reserves the right to change this information.

The manufacturer shall immediately include any modifications or additions in this manual.

2.5 Target group

Individuals working with this machine must be regularly trained on the dangers of handling the machine.

This operator's manual is intended for the following persons:

Operating personnel:

These individuals have been trained on the machine and informed about the possible dangers in the

event of improper conduct.

Technically trained personnel:

These people have professional training as well as additional knowledge and experience. They are able

to assess the tasks assigned to them and recognize possible dangers.

2.6 Explanation of symbols

This manual contains specially emphasized safety instructions in the following categories: DANGER,

WARNING, CAUTION and NOTE.

Before performing any work on or with this machine, the notes and safety instructions must be read and

understood. All notes and safety instructions in this manual must be passed on to the maintenance,

repair, and transport personnel.

DANGER

This combination of symbol and signal word indicates a hazardous situation that will lead

to death or serious injury if it is not avoided.

WARNING

This combination of symbol and signal word indicates a hazardous situation that can lead

to death or serious injury if it is not avoided.

CAUTION

This combination of symbol and signal word indicates a hazardous situation that can lead

to minor injury or damage to the machine if it is not avoided.

2 Introduction

100_0000_0013.fm 7

2.7 Wacker Neuson Contact partner

Depending on the country, the Wacker Neuson contact partner is a Wacker Neuson service, a

Wacker Neuson affiliate, or a Wacker Neuson dealer.

On the Internet at www.wackerneuson.com

The manufacturer's address can be found at the beginning of this manual.

2.8 Disclaimer

For the following violations, Wacker Neuson dismisses any liability for personal injury or material

damage:

 Failure to follow this manual.

 Unintended use.

 Deployment of untrained personnel.

 Using non-approved spare parts and accessories.

 Improper handling.

 Structural modifications of any kind.

 Failure to observe the "General Terms and Conditions" (GT&Cs).

2.9 Product identification of the machine

Data of the nameplate

The nameplate contains information that uniquely identifies this machine. This information is required for

ordering spare parts and when inquiring about technical issues.

 Enter information about the machine in the following table:

NOTE

Supplementary information.

Item Designation Your information

1 Group and model

2 Year of manufacture

3 Serial number

4 Version no.

5 Item number

3 Safety

100_0202_si_0010.fm 8

3 Safety

3.1 Policy

In keeping with the latest technological developments

The machine has been built in keeping with the latest technological developments and the recognized

technical safety rules. Nevertheless, improper use can result in hazards to life and limb of the user or

third parties as well as damage to the equipment and other material assets.

Proper use

The machine may only be used for the following purposes:

 Soil compaction.

 Asphalt compaction.

 Vibration of sett paving (paving stones).

The machine may not be used for the following purposes:

 Compaction of very cohesive soils.

 Compaction of frozen soils.

 Compaction of hard, non-compressible soils.

 Compaction of non-load-bearing soils.

Use in accordance with the intended purpose also includes the observation of all safety instructions in

this manual as well as complying with the prescribed care and maintenance instructions.

Any other use or extended use is considered not in accordance with the intended purpose. The

manufacturer's liability and warranty are canceled for any damage resulting from improper use. The risk

lies entirely with the operator.

Structural changes

Structural modifications may not be undertaken without the written permission of the manufacturer.

Unapproved structural changes may result in risks to the operator and/or third parties as well as damage

to the machine.

In the case of unauthorized structural changes, the liability and warranty of the manufacturer are no

longer applicable.

The following cases are considered structural changes:

 Opening the machine and the permanent removal of components.

 Installing spare parts that do not originate from Wacker Neuson or are not comparable in the design

system and quality of the original parts.

 Attaching any accessories that do not originate from Wacker Neuson.

Spare parts or accessories that originate from Wacker Neuson can be safely mounted. They can be

found on the Internet under www.wackerneuson.com.

NOTE

Read and comply with all notes and safety instructions in this manual. Failure to comply

with these instructions can cause electric shock, fire and/or serious injuries as well as

damage to the machine and/or damage to other objects. Keep safety instructions and

notes for the future.

3 Safety

9 100_0202_si_0010.fm

3.2 Areas of responsibility of the operator

The operator is the individual who personally operates this machine for industrial or commercial

purposes or who entrusts a third party with the use. The operator bears legal responsibility for his/her

protection as well as that of third parties.

The user must make the operator's manual available to the operator and ensure that this has been read

and understood.

The manual must be kept next to the machine or place of use.

The operator must hand over the manual to subsequent operators or owners of the machine.

The country-specific regulations, standards, and guidelines on accident prevention and environmental

protection must be observed. The operator's manual must be supplemented with additional instructions

that take regulatory, national or generally applicable safety standards into consideration.

3.3 Operator responsibilities

 Know and implement the applicable industrial safety regulations.

 Use a risk assessment to identify the dangers that result from the working conditions at the site of

application.

 Create operating instructions for the operation of this machine.

 Periodically check whether the user instructions correspond to the current state of regulations.

 Clearly regulate and specify responsibilities for operation, troubleshooting, maintenance, and

cleaning.

 Regularly train employees and inform them about potential hazards.

 Provide employees with the necessary equipment.

3.4 Personnel qualification

This machine may only be installed and operated by trained personnel.

Faulty operation, misuse or operation by untrained personnel can endanger health of the operator or

third parties and lead to damage to or total loss of the machine.

In addition, the operator should be:

 Physically and mentally fit.

 Not under the influence of drugs, alcohol or medication that can impair responsiveness.

 Familiar with the safety instructions in this manual.

 Familiar with the intended use of this machine.

 Have reached the minimum age of 18 to operate this machine.

 Be instructed in the independent operation of the machine.

 Be authorized to operate machines and systems independently according to the standards of safety

engineering.

3.5 General sources of danger

Residual dangers in particular are hazards when dealing with machines that, despite a safe design,

cannot be eliminated.

These residual dangers are not obvious and may be the source of a possible injury or health hazard.

If unforeseeable residual dangers occur, the operation of the machine is to be stopped immediately and

the competent supervisor is to be informed. This supervisor shall make the following decisions and

initiate everything required to eliminate the occurring risk.

If necessary, the machine manufacturer is to be informed.

3.6 General safety instructions

The safety instructions in this chapter include the "General Safety Instructions", which should be

reported in the manual in accordance with the applicable standards. There may be information that is

not relevant to this machine.

3 Safety

100_0202_si_0010.fm 10

3.6.1 Working area

 Before beginning work, familiarize yourself with the working environment, e.g. the load-bearing

capacity of the floor or obstacles in the vicinity.

 Make working area safe for the public transport sector.

 Necessary fuse protection of walls and ceilings, e.g. in trench applications.

 Keep the working area tidy. Cluttered or dark working areas can lead to accidents.

 Using this machine in an explosive atmosphere is prohibited.

 When using this machine, children and unauthorized individuals must be kept away. Distraction can

lead to loss of control of the machine.

 Always protect the machine against tilting, rolling, sliding, and crashing. Risk of injury!

3.6.2 Service

 The machine should only be maintained/repaired by technically trained personnel.

 Use only original spare parts and accessories. This ensures the operational safety of the machine.

3.6.3 Personal safety

 Working under the influence of drugs, alcohol, or drugs can lead to serious injuries.

 Protective equipment should be worn for all work. Appropriate personal protective equipment

considerably reduces the risk of injury.

 Remove any tools before the machine is put into operation. Tools that are located on a rotating

machine part can be ejected and cause serious injury.

 Always ensure good footing.

 In the case of extensive work with this machine, long-term vibration-induced damage cannot be ruled

out. For exact values of vibration measurement, refer to the Technical Data chapter.

 Wear suitable clothing. Keep loose clothing, gloves, jewelry, and long hair away from moving/rotating

machine parts. Danger of being pulled!

 Ensure that no other individuals are in the danger zone!

3.6.4 Handling and use

 Handle machines with care. Do not operate machines with defective components or operator's

controls. Immediately replace defective components or operator's controls. Machines with defective

components or operator's controls carry a high risk of injury!

 The operator's controls of the machine shall not be improperly locked, manipulated, or changed.

 The machine, accessories, and tools should be used in accordance with these instructions.

 Store unused machines out of reach of children. The machine may only be operated by authorized

personnel.

 After operation, store the cooled-down machine in a locked, clean, frost-protected, and dry location

that is inaccessible to children and other unauthorized individuals.

3.7 Specific safety instructions – Vibratory plates

3.7.1 External influences

In the case of the following external influences, the vibratory plate may not be operated:

 In heavy rain on sloped surfaces. Risk of slipping!

 Oil field environments – methane leaks from bottom. Explosion hazard!

 In dry, flammable vegetation. Fire hazard!

 In potentially explosive areas. Explosion hazard!

3 Safety

11 100_0202_si_0010.fm

3.7.2 Operational safety

 When operating the machine, make sure that no gas, water, or electric lines are damaged.

 The machine must not be operated in tunnels or enclosed spaces.

 Pay maximum attention near drops or slopes. Risk of crashing!

 The operator must not leave the machine while it is in operation.

 Do not leave the machine unattended. Risk of injury!

 Delimit spacious workspace and restrict access to unauthorized individuals. Risk of injury!

 Machine operators must ensure that people in the working area keep a minimum distance of 2 meters

from the running machine.

 Do not use any starting aid sprays. These can cause misfires as well as engine damage. Fire hazard!

 Always approach gradients from below when operating the machine on sloped surfaces. The

machine could slip or tip over.

 Do not exceed max. allowable slanting position of the machine – possible failure of the engine

lubrication, see chapter Technical Data.

3.7.3 Minimum safety distances

Compaction work near buildings can cause damage to buildings. Therefore, all potential effects and

vibrations on surrounding buildings must be checked in advance.

The relevant rules and regulations for measuring, evaluating and reducing vibration emissions -

especially the DIN 4150-3 - must be considered.

Wacker Neuson assumes no liability for any damage to buildings.

3.8 General safety instructions - Combustion engines

The following notes must be observed:

 Before starting work, check the engine to ensure there are no leaks and cracks in the fuel lines, tank

and fuel cap.

 Do not operate a defective engine. Replace damaged parts immediately.

 The pre-set engine speed may not be adjusted. This could lead to engine damage.

 Make sure that the exhaust system of the engine is free of debris. Fire hazard!

 Switch off the engine and allow to cool before refueling.

 Use the correct fuel type. The fuel may not be mixed with other liquids.

 Use clean filling aids for refueling. Do not spill fuel. Immediately wipe up any spilled fuel.

 The engine may not be started near spilled fuel. Explosion hazard!

 For operation in partially closed spaces, sufficient ventilation and aeration must be ensured. Do not

inhale exhaust fumes. Risk of poisoning!

 The engine surface and exhaust system can quickly become extremely hot. Risk of burns!

3.9 General safety instructions – fuel, lubricants and coolants

The following notes must be observed:

 Always wear safety glasses and protective gloves when handling fuel, lubricants, and coolants. If

hydraulic oil, fuel, oil, or coolant gets into your eyes, see a doctor immediately.

 Avoid direct skin contact with fuel, lubricants and coolants. Immediately rinse skin with soap and

water.

 Do not eat or drink while working with fuel, lubricants and coolants.

 Contaminated hydraulic oil or fuel from dirt or water can lead to premature wear or failure of the

machine.

 Dispose of spilled fuel, lubricants and coolants according to the applicable provisions for

environmental protection.

 If fuel, lubricants and coolants escape from the machine, do not operate the machine any longer and

have it repaired immediately by the Wacker Neuson contact partner.

NOTE

This machine is outfitted with an EPA-certified engine.

Changing the revolutions per minute (RPM) impacts the EPA-certification and the

emissions. Settings for this engine may only be changed by a professional.

For more information, contact the manufacturer or your Wacker Neuson contact partner.

3 Safety

100_0202_si_0010.fm 12

3.10 Maintenance

The following notes must be observed:

 This machine may not be maintained, repaired, adjusted or cleaned while switched on.

 Adhere to maintenance intervals.

 After each maintenance or repair, the safety devices on this machine must be reattached.

 Observe the maintenance schedule. Non-listed work must be taken over by the service department

of the Wacker Neuson contact partner.

 Immediately replace worn or damaged machine parts. Only use spare parts from Wacker Neuson.

 Keep the machine clean.

 Missing, damaged, or illegible safety warning labels should be replaced immediately. Safety stickers

contain important information for the protection of the operator.

 Maintenance jobs must be performed in a clean and dry vicinity (e.g. workshop).

3.11 Personal Protective Equipment

NOTE

To prevent personal injury when handling this machine, personal protective equipment

must be worn when working on or around this machine.

Pictogram Significance Description

Wear safety shoes! Safety shoes provide protection from bruises, falling

objects, and slipping.

Wear protective gloves! Protective gloves provide protection from abrasion,

cuts, punctures, and hot surfaces.

Wear ear protection! Ear protection provides protection from permanent

hearing impairment.

NOTE

With this machine, the permissible, country-specific noise limit (personal rating level) may

be exceeded. Therefore, ear protection must be worn. For exact values of noise

emissions, refer to the Technical Data section.

Work particularly cautiously and pay attention when wearing ear protection, as your ability

to hear noises, such as screams or signal tones, is restricted.

Wacker Neuson recommends always wearing ear protection.

3 Safety

13 100_0202_si_0010.fm

3.12 Safety devices

Safety devices protect the user of this machine from being exposed to existing hazards. These are

barriers (separating protective devices) or other technical measures. This prevents the user from being

exposed to a danger. The source of danger will be eliminated in certain situations or the danger will be

reduced.

This machine has the following safety equipment:

3.13 Behavior in dangerous situations

Preventive measures:

 Always be prepared for accidents.

 Keep first aid equipment on hand.

 Make sure that all employees are familiar with accident reporting, first aid, and rescue facilities.

 Keep access routes clear for emergency vehicles.

 Make sure that employees receive first aid training.

Measures in the case of an emergency:

 Immediately take the machine out of operation.

 Remove injured and other people from the danger zone.

 Initiate first aid measures.

 Alert rescuers.

 Keep access routes clear for emergency vehicles.

 Inform the person responsible at the site of application.

Item Description

1 Belt guard

NOTE

Always tighten loosened screwed connections with the prescribed torque setting.

1

4 Safety and information labels

100_0202_ls_0011.fm 14

4 Safety and information labels

The following labels are located on the machine:

WARNING

Illegible symbols

Over time, labels and signs on the machines can become dirty or otherwise

unrecognizable.

 Keep all safety, warning, and operating instructions on the machine in a legible

condition.

 Replace damaged labels and signs immediately.

WP VP

1

2

3

5

4

6

7

8

9

1

2

3

4

5

6

8

9

4 Safety and information labels

15 100_0202_ls_0011.fm

Item Label Description

1 Start/Stop.

2 Use personal protection equipment in order to prevent injuries

and health hazards.

 Ear protection.

 Read operator's manual.

 Start/Stop description.

3 Falling machines can cause serious injury.

 Only lift machine at the central lifting point with certified lifting

gear and tackle (safety load hook).

 Do not lift the machine on the central lifting point with an

excavator bucket.

4 Falling machines can cause serious injury.

 Do not lift the machine at the control handle.

5 Flames are prohibited.

6 Guaranteed sound power level.

7 Patent pending.

8 US Machines Warning.

9 US Machines Danger.

0219260

0

2

0

2

1

9

1

8

1

5 Setup and function

100_0202_sf_0012.fm 16

5 Setup and function

5.1 Standard package

The standard package includes:

 Vibratory plate

 The control handle is included separately for the vibratory plate WP.

 The vibratory plate VP is complete.

 Operator's manual

5.2 Application areas

The vibratory plate is used for compacting soil. It is used in gardening and landscaping as well as civil

engineering, road construction, and paving.

5.3 Short description

The vibratory plate is a machine used to compact soils.

The vibration required for the compaction is generated by the exciter firmly connected to the base plate.

This exciter is designed as a single directional, front mounted exciter with circular vibrations.

The drive motor attached to the engine console drives the exciter. The torque is firmly transferred

through the centrifugal clutch and the exciter V-belt.

At low engine speeds, the centrifugal clutch interrupts the force flow to the exciter and thereby allows a

flawless idling of the drive motor. The revolutions per minute (RPM) of the drive motor can be changed

at the throttle lever from full throttle to idling and to stop.

The engine console and base plate are connected to each other through 4 vibration-absorbing rubber

metal buffers. This damping prevents a transfer of the very high frequencies to the engine console. The

functionality of the drive motor therefore remains preserved, despite the high compaction performance.

The drive motor works through a recoil starter, draws the combustion air through a dry-type air cleaner

and is air-cooled.

5.4 Versions

This operator's manual covers the following models:

Versions Description

W Water tank

6 Components and operator's controls

17 100_0202_cp_0008.fm

6 Components and operator's controls

6.1 Components

6.2 Operator's controls

Always keep the display and operator's controls on the machine clean, dry, and free of oil and grease.

Operator's controls, such as the ON/OFF switch, throttle control handles, etc. may not be locked,

manipulated or changed without permission.

WP VP

Item Designation Item Designation

1 Drive motor 5 Belt guard

2 Base plate 6 Water tank (optional)

3 Exciter 7 Handle grip (VP)

4 Protective frame (WP) 8 Nameplate

WP VP WP/VP

Item Designation Item Designation

1 Control handle 4 Fuel cock

2 Throttle lever 5 Choke lever

3 Handle recoil starter 6 Engine switch

1

2

3

4

5

6

8

1

2

3

5

6

7

8

1

6

1

6

2

5

4

3

7 Transport

100_0202_tr_0011.fm 18

7 Transport

7.1 Loading and transport

Previous conditions

 To transport the vibratory plate, only use suitable lifting gear with a minimum load-bearing capacity

of 150 kg.

 Always switch off the engine during transport!

 Attach suitable tackle to the intended central lifting point.

Carry out preparations

During loading and transport, the control handle must be folded down.

WARNING

Improper handling may result in injury or serious material damage.

 Please read and follow all safety instructions in this operator's manual.

DANGER

Danger from falling.

Falling machines can cause serious injury e.g. through crushing.

 Only use suitable and tested lifting gear and tackle (safety load hooks) of sufficient

lifting capacity.

 Only lift the machine from the central lifting point.

 Reliably secure the machine to the lifting gear.

 Do not lift the machine with a crane by the control handle and handle grip.

 Evacuate danger zone while lifting, do not stop under suspended loads.

WARNING

Risk of fire and explosion from fuel.

Escaping fuel may catch fire and cause serious burns.

 Lift and transport the machine upright.

NOTE

Wacker Neuson recommends emptying the fuel tank prior to transport.

7 Transport

19 100_0202_tr_0011.fm

Lifting and lashing down the machine

1. To lift the motor, hang suitable tackle at the central lifting point.

2. Carefully load machine into or onto a stable means of transport.

3. After loading the machine, lash down the machine to prevent it from rolling off, slipping, or tipping

over. Attach tie-down lugs to the designated lashing points.

NOTE

Appoint a specialist flagman for a safe lifting operation.

WP VP

Item Designation

1 Central lifting point

WP VP

1

8 Operation and use

100_0202_op_0014.fm 20

8 Operation and use

8.1 Initial operation

8.1.1 WP

The supplied control handle needs to be attached prior to initial operation.

1. Align the control handle on the provided bores.

2. Tighten the control handle on the left and right with the screws. The torque setting is 86 Nm.

8.1.2 VP

The machine is delivered fully assembled and is ready for operation out of the box.

8.2 Before commissioning

8.2.1 Inspection before commissioning

 Check the machine and components for damage. In the event of visible damage, do not operate the

machine and immediately contact Wacker Neuson service.

 Ensure that loose packaging material has been removed from the machine.

 Check the fuel level.

 Check the engine oil level.

 Check the fuel lines for leak tightness.

 Check to ensure the screwed connections are firmly seated.

8.3 Notes about operation

WARNING

Improper handling may result in injury or serious material damage.

 Please read and follow all safety instructions in this operator's manual.

Item Designation

1 Control handle

NOTE

Perform control procedures according to the Maintenance chapter. If necessary, top off

missing fuel, lubricants and coolants, see chapterTechnical Data.

WARNING

Danger of tipping

There is a serious risk of injury from slipping or tipping over of the machine.

Near edges, at least 2/3 of the machine must be on a load-bearing surface.

 Turn off the machine and lift it back onto a load-bearing surface.

1

La page charge ...

Wacker Neuson VP1030A Manuel utilisateur

Wacker Neuson VP1030A Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents