Generac XG4000 0057781 Manuel utilisateur

Marque: Generac

Modèle: XG4000 0057781

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

www.generac.com or 1-888-436-3722

Owner's Manual

XG4000 Series Portable Generator



DEADLY EXHAUST FUMES! ONLY use OUTSIDE

far away from windows, doors and vents!



NOT INTENDED FOR USE IN CRITICAL LIFE

SUPPORT APPLICATIONS.



SAVE this Manual. Provide this manual to any

operator of the generator.

Introduction ..............................................................................1

Read this Manual Thoroughly ..................................................1

Safety Rules ............................................................................1

Standards Index .......................................................................3

General Information .................................................................4

1.1 Unpacking ................................................................................4

1.1.1 Accessory Box ............................................................4

1.2 Assembly .................................................................................4

1.2.1 Assembling the Wheel Kit and Frame Foot ...................4

Operation .................................................................................5

2.1 Know the Generator .................................................................5

2.2 Hourmeter - No Reset ..............................................................6

2.3 Hourmeter - With Reset............................................................6

2.4 Cord Sets and Connection Plugs ..............................................6

2.4.1 120 VAC,20 Amp, GFCI Duplex Receptacle ..................6

2.4.2 120/240 VAC, 20 Amp Receptacle ..............................7

2.5 How to Use the Generator ........................................................7

2.5.1 Grounding the Generator When Used as a Portable ......7

2.5.2 Connecting the Generator to a Building's

Electrical System .........................................................8

2.5.3 Neutral to Frame Grounding .........................................8

2.5.4 Connecting Electrical loads ..........................................8

2.6 Don’t Overload the Generator ...................................................8

2.7 Wattage Reference Guide .........................................................9

2.8 Before Starting the Generator ...................................................9

2.8.1 Adding Engine Oil ........................................................9

2.8.2 Adding Gasoline ........................................................10

2.9 To Start the Engine .................................................................10

2.10 Stopping the Engine ...............................................................11

2.11 Low Oil Pressure Shutdown System .......................................11

2.11.1 Restarting..................................................................11

Maintenance ..........................................................................11

3.1 Performing Scheduled Maintenance .......................................11

3.2 Maintenance Schedule ...........................................................11

3.3 Product Specifications ...........................................................11

3.3.1 Generator Specifications .............................................11

3.3.2 Engine Specifications .................................................11

3.3.3 Emissions Information ................................................12

3.4 General Recommendations ....................................................12

3.4.1 Generator Maintenance ...............................................12

3.4.2 To Clean the Generator ...............................................12

3.4.3 Engine Maintenance ...................................................12

3.4.4 Checking Oil Level ......................................................12

3.4.5 Changing the Oil and Oil Filter .....................................12

3.4.6 Replacing the Spark Plug ............................................13

3.5 Service Air Filter .....................................................................13

3.6 Clean Spark Arrestor Screen ..................................................13

3.7 General ..................................................................................14

3.8 Long Term Storage.................................................................14

3.9 Other Storage Tips .................................................................14

Troubleshooting .....................................................................15

4.1 Troubleshooting Guide ............................................................15

Notes .....................................................................................16

Warranty ................................................................................18

MANUAL DEL USUARIO .................................... 23

MANUEL DE L'UTILISATEUR ............................. 45

Table of Contents

INTRODUCTION

Thank you for purchasing this model by Generac Power Systems,

Inc. This model is a compact, high performance, air-cooled,

engine driven generator designed to supply electrical power to

operate electrical loads where no utility power is available or in

place of utility due to a power outage.

READ THIS MANUAL THOROUGHLY

If any portion of this manual is not understood, contact the

nearest Authorized Dealer for starting, operating and servicing

procedures.

The operator is responsible for proper and safe use of the

equipment. We strongly recommend that the operator read this

manual and thoroughly understand all instructions before using the

equipment. We also strongly recommend instructing other users to

properly start and operate the unit. This prepares them if they need

to operate the equipment in an emergency.

The generator can operate safely, efficiently and reliably only if it

is properly located, operated and maintained. Before operating or

servicing the generator:

• Become familiar with and strictly adhere to all local, state and

national codes and regulations.

• Study all safety warnings in this manual and on the product

carefully.

• Become familiar with this manual and the unit before use.

The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, therefore, not all inclusive.

If using a procedure, work method or operating technique that the

manufacturer does not specifically recommend, ensure that it is

safe for others. Also make sure the procedure, work method or

operating technique utilized does not render the generator unsafe.

THE INFORMATION CONTAINED HEREIN WAS BASED ON

MACHINES IN PRODUCTION AT THE TIME OF PUBLICATION.

GENERAC RESERVES THE RIGHT TO MODIFY THIS MANUAL AT

ANY TIME.

SAFETY RULES

Throughout this publication, and on tags and decals affixed to the

generator, DANGER, WARNING, CAUTION and NOTE blocks are

used to alert personnel to special instructions about a particular

operation that may be hazardous if performed incorrectly or

carelessly. Observe them carefully. Their definitions are as

follows:

INDICATES A HAZARDOUS SITUATION OR ACTION WHICH, IF

NOT AVOIDED, WILL RESULT IN DEATH OR SERIOUS INJURY.

Indicates a hazardous situation or action which, if not

avoided, could result in death or serious injury.

Indicates a hazardous situation or action which, if not

avoided, could result in minor or moderate injury.

NOTE:

Notes contain additional information important to a procedure

and will be found within the regular text body of this manual.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliance with the special

instructions while performing the action or service are essential to

preventing accidents.

Four commonly used safety symbols accompany the DANGER,

WARNING and CAUTION blocks. The type of information each

indicates is as follows:



This symbol points out important safety

information that, if not followed, could

endanger personal safety and/or property of

others.





This symbol points out potential explosion

hazard.



This symbol points out potential fire hazard.



This symbol points out potential electrical

shock hazard.

GENERAL HAZARDS

• NEVER operate in an enclosed area, in a vehicle, or indoors

EVEN IF doors and windows are open.

• For safety reasons, the manufacturer recommends that the

maintenance of this equipment is carried out by an Authorized

Dealer. Inspect the generator regularly, and contact the nearest

Authorized Dealer for parts needing repair or replacement.

• Operate generator only on level surfaces and where it will not be

exposed to excessive moisture, dirt, dust or corrosive vapors.

• Keep hands, feet, clothing, etc., away from drive belts, fans,

and other moving parts. Never remove any fan guard or shield

while the unit is operating.

• Certain parts of the generator get extremely hot during

operation. Keep clear of the generator until it has cooled to

avoid severe burns.

• Do NOT operate generator in the rain.

• Do not alter the construction of the generator or change

controls which might create an unsafe operating condition.

• Never start or stop the unit with electrical loads connected

to receptacles AND with connected devices turned ON. Start

the engine and let it stabilize before connecting electrical

loads. Disconnect all electrical loads before shutting down the

generator.

• Do not insert objects through unit’s cooling slots.

• When working on this equipment, remain alert at all times.

Never work on the equipment when physically or mentally

fatigued.

Introduction

• Never use the generator or any of its parts as a step. Stepping

on the unit can stress and break parts, and may result in

dangerous operating conditions from leaking exhaust gases,

fuel leakage, oil leakage, etc.

NOTE:

This generator is equipped with a spark arrestor muffler. The

spark arrestor must be maintained in effective working order

by the owner/ operator. In the State of California, a spark

arrestor is required by law (Section 4442 of the California

Public Resources Code). Other states may have similar laws.

Federal laws apply on federal lands.

EXHAUST & LOCATION HAZARDS

• Never operate in an enclosed area or indoors! NEVER use

in the home, in a vehicle, or in partly enclosed areas such

as garages, even if doors and windows are open! ONLY use

outdoors and far from open windows, doors, vents, and in an

area that will not accumulate deadly exhaust.

• The engine exhaust fumes contain carbon monoxide, which

you cannot see or smell. This poisonous gas, if breathed in

sufficient concentrations, can cause unconsciousness or even

death.

• Adequate, unobstructed flow of cooling and ventilating air

is critical to correct generator operation. Do not alter the

installation or permit even partial blockage of ventilation

provisions, as this can seriously affect safe operation of the

generator. The generator MUST be operated outdoors.

• This exhaust system must be properly maintained. Do nothing

that might render the exhaust system unsafe or in noncompliance

with any local codes and/or standards.

• Always use a battery operated carbon monoxide alarm indoors,

installed according to the manufacturer's instructions.

• If you start to feel sick, dizzy, or weak after the generator has

been running, move to fresh air IMMEDIATELY. See a doctor, as

you could have carbon monoxide poisoning.

ELECTRICAL HAZARDS

• The generator produces dangerously high voltage when in

operation. Avoid contact with bare wires, terminals, connections,

etc., while the unit is running, even on equipment connected

to the generator. Ensure all appropriate covers, guards and

barriers are in place before operating the generator.

• Never handle any kind of electrical cord or device while

standing in water, while barefoot or while hands or feet are wet.

DANGEROUS ELECTRICAL SHOCK MAY RESULT.

• The National Electric Code (NEC) requires the frame and external

electrically conductive parts of the generator be properly

connected to an approved earth ground. Local electrical codes

may also require proper grounding of the generator. Consult

with a local electrician for grounding requirements in the area.

• Use a ground fault circuit interrupter in any damp or highly

conductive area (such as metal decking or steel work).

• Do not use worn, bare, frayed or otherwise damaged electrical

cord sets with the generator.

• Before performing any maintenance on the generator, disconnect

the engine starting battery (if equipped) to prevent accidental

start up. Disconnect the cable from the battery post indicated

by a NEGATIVE, NEG or (–) first. Reconnect that cable last.

• In case of accident caused by electric shock, immediately shut

down the source of electrical power. If this is not possible,

attempt to free the victim from the live conductor. AVOID

DIRECT CONTACT WITH THE VICTIM. Use a non-conducting

implement, such as a rope or board, to free the victim from the

live conductor. If the victim is unconscious, apply first aid and

get immediate medical help.

FIRE HAZARDS

• Gasoline is highly FLAMMABLE and its vapors are EXPLOSIVE.

Do not permit smoking, open flames, sparks or heat in the

vicinity while handling gasoline.

• Never add fuel while unit is running or hot. Allow engine to

cool completely before adding fuel.

• Never fill fuel tank indoors. Comply with all laws regulating

storage and handling of gasoline.

• Do not overfill the fuel tank. Always allow room for fuel

expansion. If tank is over-filled, fuel can overflow onto a hot

engine and cause FIRE or an EXPLOSION. Never store generator

with fuel in tank where gasoline vapors might reach an open

flame, spark or pilot light (as on a furnace, water heater or

clothes dryer). FIRE or EXPLOSION may result. Allow unit to

cool entirely before storage.

• Wipe up any fuel or oil spills immediately. Ensure that no

combustible materials are left on or near the generator. Keep the

area surrounding the generator clean and free from debris and

keep a clearance of five (5) feet on all side to allow for proper

ventilation of the generator.

• Do not insert objects through unit’s cooling slots.

• Do not operate the generator if connected electrical devices

overheat, if electrical output is lost, if engine or generator sparks

or if flames or smoke are observed while unit is running.

• Keep a fire extinguisher near the generator at all times.

Safety Rules

STANDARDS INDEX

In the absence of pertinent standards, codes, regulations and laws,

the published information listed below may be used as a guideline

for operation of this equipment. Always reference the latest revision

available for the standards listed.

1. National Fire Protection Association (NFPA) 70: The NATIONAL

ELECTRIC CODE (NEC) available from www.nfpa.org

2. National Fire Protection Association (NFPA) 5000: BUILDING

CONSTRUCTION AND SAFETY CODE available from www.

nfpa.org

3. International Building Code available from www.iccsafe.org

4. Agricultural Wiring Handbook available from www.rerc.org ,

Rural Electricity Resource Council P.O. Box 309 Wilmington,

OH 45177-0309

5. ASAE EP-364.2 Installation and Maintenance of Farm Standby

Electric Power available from www.asabe.org, American

Society of Agricultural & Biological Engineers 2950 Niles

Road, St. Joseph, MI 49085

This list is not all inclusive. Check with the Authority Having Local

Jurisdiction (AHJ) for any local codes or standards which may be

applicable to your jurisdiction.

MODEL NO:

SERIAL NO:

CALIFORNIA PROPOSITION 65 WARNING

Engine exhaust and some of its constituents are known

to the State of California to cause cancer, birth defects

and other reproductive harm.

CALIFORNIA PROPOSITION 65 WARNING

This product contains or emits chemicals known to the

State of California to cause cancer, birth defects and

other reproductive harm.

Safety Rules

Unit ID

Locations

1.1 UNPACKING

• Remove all packaging material.

• Remove separate accessory box.

• Remove carton off the generator.

1.1.1 ACCESSORY BOX

Check all contents (Figure 1). If any parts are missing or damaged

locate an authorized dealer at 1-888-436-3722.

Contents include:

• 2 – Axle Pins • Oil Filter

• 2 – Wheel Spacers • Air Filter

• 2 – Hair Pins • Spark Plug

• 2 – Wheels • Spark Plug Wrench

• 1 – Frame Foot • Shop Towel

• 1 – Frame Bolt • 1 Quart SAE 30 Oil Bottle

• 1 – Frame Flat Washer • Oil Funnel

• 3 – Flange Nuts • 2 – Vibration Mounts

Figure 1 – Accessory Box

1.2 ASSEMBLY

Read entire Owner's Manual before attempting to assemble or

operate the generator. The generator requires some assembly

prior to using it. If problems arise when assembling the generator,

please call the Generator Helpline at 1-888-436-3722.

1.2.1 ASSEMBLING THE WHEEL KIT AND FRAME FOOT

The wheel kit is designed to greatly improve the portability of the

generator. You will need the following tools to install the wheel kit:

• Pliers

• 1/2" (13mm) Wrench

• Socket Wrench with a 1/2" (13mm) socket.

NOTE:

The wheels are not intended for over-the-road use.

Refer to Figure 2 and install the wheel kit and frame foot as follows:

1. Slide the Axle Pin through the Wheel, Wheel Spacer (Washer)

and the Frame.

2. Install the Hair Pin to the Axle Pin to secure the wheel. Repeat

for the opposite side.

3. Secure the Vibration Mounts to the Frame Foot with the

included locking nuts.

4. To install the Frame Foot, remove the lock nut from the

Vibration Mount stud.

5. Place the Frame Foot on the Vibration Mount stud and

re-install the lock nut. Tighten the nut completely.

6. Install the Frame Bolt through the Frame Washer, Frame and

Frame foot. Secure with a flange nut.

Figure 2 – Wheel and Foot Assembly

ASSEMBLE

FRAME

FOOT

RE-USE THIS

NUT FROM

VIBRATION

MOUNT

SECURE WHEEL

AND AXLE WITH

HAIR PIN

SLIDE AXLE

THROUGH WHEEL

AND WHEEL

SPACER

WHEEL SPACER

(WASHER)

FRAME

BOLT

FRAME

WASHER

FLANGE

NUT

INSTALL FRAME FOOT

General Information

2.1 KNOW THE GENERATOR

Read the Owner’s Manual and Safety Rules before operating

this generator.

Compare the generator to Figure 3 to become familiarized with the

locations of various controls and adjustments. Save this manual

for future reference.

1. Run/Stop Switch – Controls the operation of the generator.

2. Fuel Shut Off – Valve between fuel tank and carburetor. Turn

off and run carburetor out of fuel for extended storage.

3. Panel LED's – Provide illumination of the control panel while

the generator is operating.

4. 120/240 Volt AC, 20 Amp Locking Receptacle – Supplies

electrical power for the operation of 120 and/or 240 Volt AC,

20 Amp, single-phase, 60 Hz, electrical lighting, appliance,

tool and motor loads.

5. 120 Volt AC, 20 Amp, GFCI Duplex Receptacle – Supplies

electrical power for the operation of 120 Volt AC, 20 Amp,

single-phase, 60 Hz electrical lighting, appliance, tool and

motor loads. It also provides protection with an Integral

Ground Fault Circuit Interrupter, complete with a press to

"Test" and "Reset" button.

6. Circuit Breakers (AC) – The push-to-reset circuit breakers

(49 state model) or the 2-pole circuit breaker (CSA/CARB

models) are rated at 20 Amps; this protects the generator

against electrical overload.

7. Hourmeter – Provides operating hours for Service Intervals.

8. PowerBar – Indicates the amount of power being used from

the generator; each section is approximately 20%.

9. Fuel Tank – Tank holds 4.5 U.S. gallons of fuel.

10. Fuel Gauge – Shows fuel level in tank.

11. Handles – Pivot and retract for storage. Press the spring-

loaded button to move handles.

12. Oil Fill – Check oil level and add oil here.

13. Grounding Lug – Ground the generator to an approved earth

ground here. See "Grounding the Generator" for details.

14. Muffler – Includes the spark arrestor and quiets the engine.

15. Spark Plug – Ignites Air/Fuel Mixture (Side panel must be

removed).

16. Engine Oil Filter – Filters engine oil; see Section 3.1 for the

proper service intervals.

17. Choke – Used when starting a cold engine.

18. Air Cleaner – Filters intake air as it is drawn into the engine.

19. Oil Drain – Drain valve to remove used oil from the engine

crankcase.

20. Recoil Starter – Use to start engine manually.

*21. Carbon Canister - Absorbs fuel tank vapors.

22. Roll Over Valve - Passes fuel vapors to the carbon canister.

23. Recovery Hose - Installed between the engine air intake, the

carbon canister and the Roll Over Valve.

* California model only.

Figure 3 – Generator Locations and Controls

49 State

CSA/CARB

Operation

2.2 HOURMETER - NO RESET

The Hourmeter tracks hours of operation for scheduled

maintenance:

There will be a one time break in "CHG OIL" message that flashes

with the elapsed time in hours and tenths after the first 30 hours

of operation.

This message will actually begin flashing at 29 hours and disable

itself at 31 hours providing a two hour window to perform the

service.

There will be a subsequent "CHG OIL" message every 100 hours.

The message will flash one hour before and one hour after each

100 hour interval, again providing a two hour window to perform

service.

Every 200 hours the "SVC" icon on the lower left hand corner of

the display will flash. The message will flash one hour before and

one hour after each 200 hour interval providing a two hour window

to perform service.

When the hour meter is in the Flash Alert mode, the maintenance

message will always alternate with elapsed time in hours and

tenths. The hours will flash four times, then alternate with the

maintenance message four times until the meter resets itself.

• 100 hours - CHG OIL — Oil Change Interval (Every 100 hrs)

• 200 hours - SVC — Air Filter Interval (Every 200 hrs)

2.3 HOURMETER - WITH RESET

The Hourmeter tracks hours of operation for scheduled maintenance

(see chart).

Operation: Push and release the reset button to toggle between

screens. The hours count backwards from the set interval as

shown in the chart.

When the meter reaches 5 hours,the text "CHG OIL" (or "SVC AIR

FILTER" or "CHG PLUG") will flash continually for two minutes.

After this time, the meter will go back to displaying the total hours

of the unit (for 2 minutes). This cyle will repeat for the entire 5

hours.

When the service interval reaches zero hours, the text "NOW"

replaces the hours remaining.

For a new generator for instance, the message will say "CHG OIL"

then flash "in 30". This means that in 30 hours, the oil will need to

be changed. Pressing the button a few more times will bring the

meter back to the screen that shows the total hours run.

Reset: Toggle to the alert that you wish to reset then hold the

button down for 9 seconds. The maintenance hours are reset when

the display shows "0000.0".

NOTE:

The hour glass graphic will flash on and off when the engine

is running. This signifies that the meter is tracking hours of

operation.

Figure 4 – Hourmeter

HOUR GLASS

GRAPHIC

RESET BUTTON

(IF EQUIPPED)

0000.0

2.4 CORD SETS AND CONNECTION PLUGS

2.4.1 120 VAC, 20 AMP, GFCI DUPLEX RECEPTACLE

This is a 120 Volt outlet protected against overload by a 20 Amp

push-to-reset circuit breaker (Figure 5). Use each socket to power

120 Volt AC, single phase, 60 Hz electrical loads requiring up to a

combined 2400 watts (2.4 kW) or 20 Amps of current. Use only

high quality, well-insulated, 3-wire grounded cord sets rated for

125 Volts at 20 Amps (or greater). A cord set 15 feet or shorter

is preferred.

Keep extension cords as short as possible to prevent voltage drop

and possible overheating of wires.

Operation

Hourmeter (With Reset) Chart

Message Frequency of Message Interval Duration of message

CHG OIL Initial break-in period First 30 Hours

ON/OFF for 2 minutes in a 5

hour period

CHG OIL Re-occuring 100 hours

SVC AIR FILTER Re-occuring 200 hours

CHG PLUG Re-occuring 200 hours

Figure 5 - 120 Volt AC, 20 Amp, GFCI Duplex Receptacle

2.4.2 120/240 VAC, 20 AMP RECEPTACLE

Use a NEMA L14-20 plug with this receptacle (rotate to lock/

unlock). Connect a suitable 4-wire grounded cord set to the plug

and to the desired load. The cord set should be rated for 250 Volts

AC at 20 Amps (or greater) (Figure 6).

Figure 6 - 120/240 Volt AC, 20 Amp Receptacle

Use this receptacle to operate 120 Volt AC, 60 Hz, single phase

loads requiring up to 2400 watts (2.4 kW) of power at 20 Amps

or 240 Volt AC, 60 Hz, single phase loads requiring up to 4000

watts (4.0 kW) of power at 16.6 Amps. The outlet is protected by

a circuit breaker.

2.5 HOW TO USE THE GENERATOR

See the "To Start the Engine" section for how to safely start and

stop the generator and how to connect and disconnect loads. If

there are any problems operating the generator, please call the

generator helpline at 1-888-436-3722.



Never operate in an enclosed area or indoors!

NEVER use in the home, in a vehicle, or in

partly enclosed areas such as garages, EVEN

IF doors and windows are open! ONLY use

outdoors and far from open windows, doors,

vents, and in an area that will not accumulate

deadly exhaust.



The engine exhaust fumes contain carbon

monoxide, which can you cannot see or smell.

This poisonous gas, if breathed in sufficient

concentrations, can cause unconsciousness or

even death.



Adequate, unobstructed flow of cooling and

ventilating air is critical to correct generator

operation. Do not alter the installation or permit

even partial blockage of ventilation provisions,

as this can seriously affect safe operation

of the generator. The generator MUST be

operated outdoors.



This exhaust system must be properly

maintained. Do nothing that might render the

exhaust system unsafe or in noncompliance

with any local codes and/or standards.



Always use a battery operated carbon

monoxide alarm indoors, installed according to

the manufacturers instructions.

2.5.1 GROUNDING THE GENERATOR WHEN USED AS A

PORTABLE

This generator has an equipment ground that connects the

generator frame components to the ground terminals on the AC

output receptacles (see NEC 250.34 (A) for explanation). This

allows the generator to be used as a portable without grounding

the frame of the generator as specified in NEC 250.34.

Special Requirements

There may be Federal or State Occupational Safety and Health

Administration (OSHA) regulations, local codes, or ordinances that

apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or the

local agency having jurisdiction:

• In some areas, generators are required to be registered with local

utility companies.

• If the generator is used at a construction site, there may be

additional regulations which must be observed.

Operation

2.5.2 CONNECTING THE GENERATOR TO A BUILDING’S

ELECTRICAL SYSTEM

Connections for standby power to a building’s electrical system

must be made by a qualified electrician and in strict compliance

with all national and local electrical codes and laws. The

connection must isolate the generator power from utility power or

other alternative power sources.

NOTE:

Because the generator equipment ground is bonded to the AC

neutral wires in the generator (see Figure 8), either a 3-pole

transfer switch or a 2 pole transfer switch with a switching

neutral kit is required to connect this generator to a building

load. In this application the generator becomes a separately

derived system (see NEC 250.20 (D)), and must be grounded

in accordance with the national or local electrical code

requirements.

Grounding the Generator in a Building Standby Application

The National Electrical Code requires that the frame and

external electrically conductive parts of this generator be

properly connected to an approved earth ground (Figure 7).

Local electrical codes also require grounding of the unit. For

that purpose, connecting a No. 10 AWG (American Wire Gauge)

stranded copper wire to the grounding lug and to an earth-driven

copper or brass grounding rod (electrode) provides adequate

protection against electrical shock. However, local codes may

vary widely. Consult with a local electrician for grounding

requirements in the area.

Proper grounding of the generator will help prevent electrical

shock in the event of a ground fault condition in the generator

or in connected electrical devices. Proper grounding also helps

dissipate static electricity, which often builds up in ungrounded

devices.

Figure 7 - Grounding the Generator

CONNECT GENERATOR GROUND HERE

2.5.3 NEUTRAL TO FRAME GROUNDING

If service work is performed on the alternator, DO NOT discard

the white jumper wires from the terminal block to the alternator

ground, located on the rear bearing carrier. Always make sure

the wires are properly connected before using the generator after

alternator service work is done (Figure 8).

Figure 8 - Neutral to Frame Ground Wires

DO NOT DISCARD

THESE WIRES!

NEUTRAL TO

FRAME GROUND



Failure to reconnect these wires may create a

potential shock hazard when the generator is

running!

2.5.4 CONNECTING ELECTRICAL LOADS

DO NOT connect 240 Volt loads to 120 Volt receptacles.

DO NOT connect 3 phase loads to the generator.

DO NOT connect 50 Hz loads to the generator.

• Let engine stabilize and warm up for a few minutes after

starting.

• Plug in and turn on the desired 120 or 240 Volt AC, single

phase, 60 Hz electrical loads.

• Add up the rated watts (or amps) of all loads to be connected

at one time. This total should no be greater than (a) the rated

wattage/amperage capacity of the generator or (b) circuit

breaker rating of the receptacle supplying the power. See “Don’t

Overload the Generator

2.6 DON’T OVERLOAD THE GENERATOR

Overloading a generator in excess of its rated wattage capacity

can result in damage to the generator and to connected electrical

devices. Observe the following to prevent overloading the unit:

• Add up the total wattage of all electrical devices to be connected

at one time. This total should NOT be greater than the

generator's wattage capacity.

• The rated wattage of lights can be taken from light bulbs. The

rated wattage of tools, appliances and motors can usually be

found on a data label or decal affixed to the device.

• If the appliance, tool or motor does not give wattage, multiply

volts times ampere rating to determine watts (volts x amps =

watts).

Operation

• Some electric motors, such as induction types, require about

three times more watts of power for starting than for running.

This surge of power lasts only a few seconds when starting

such motors. Make sure to allow for high starting wattage when

selecting electrical devices to connect to the generator:

1. Figure the watts needed to start the largest motor.

2. Add to that figure the running watts of all other connected

loads.

The Wattage Reference Guide is provided to assist in determining

how many items the generator can operate at one time.

2.7 WATTAGE REFERENCE GUIDE

NOTE:

All figures are approximate. See data label on appliance for

wattage requirements.

Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Running Watts

*Air Conditioner (12,000 Btu). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1700

*Air Conditioner (24,000 Btu). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3800

*Air Conditioner (40,000 Btu). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6000

Battery Charger (20 Amp) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

Belt Sander (3") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000

Chain Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Circular Saw (6-1/2") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800 to 1000

*Clothes Dryer (Electric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5750

*Clothes Dryer (Gas) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

*Clothes Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1150

Coffee Maker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1750

*Compressor (1 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000

*Compressor (3/4 HP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1800

*Compressor (1/2 HP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1400

Curling Iron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

*Dehumidifier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650

Disc Sander (9"). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Edge Trimmer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

Electric Blanket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400

Electric Nail Gun. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Electric Range (per element). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1500

Electric Skillet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1250

*Freezer . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .700

*Furnace Fan (3/5 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 875

*Garage Door Opener. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 to 750

Hair Dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Hand Drill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 to 1100

Hedge Trimmer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450

Impact Wrench. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

Iron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

*Jet Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800

Lawn Mower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Light Bulb. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Microwave Oven. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700 to 1000

*Milk Cooler. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1100

Oil Burner on Furnace. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300

Oil Fired Space Heater (140,000 Btu) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400

Oil Fired Space Heater (85,000 Btu) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225

Oil Fired Space Heater (30,000 Btu) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150

*Paint Sprayer, Airless (1/3 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600

Paint Sprayer, Airless (handheld) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150

Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 to 200

*Refrigerator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

Slow Cooker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200

*Submersible Pump (1-1/2 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2800

*Submersible Pump (1 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000

*Submersible Pump (1/2 HP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1500

*Sump Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800 to 1050

*Table Saw (10") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1750 to 2000

Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 to 500

Toaster. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000 to 1650

Weed Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

* Allow 3 times the listed watts for starting these devices.

2.8 BEFORE STARTING THE GENERATOR

Prior to operating the generator, engine oil and gasoline will need

to be added, as follows:

2.8.1 ADDING ENGINE OIL

All oil should meet minimum American Petroleum Institute (API)

Service Class SJ, SL or better. Use no special additives. Select

the oil's viscosity grade according to the expected operating

temperature (also see chart).

• Above 40° F, use SAE 30

• Below 40° F and down to 10° F, use 10W-30

• Below 10° F, use synthetic 5W-30

10W-30

10W - 3 0

SAE 30

SAE 3 0

Synthetic 5W-30

Sy n t heti c 5W-3 0



Any attempt to crank or start the engine

before it has been properly serviced with the

recommended oil may result in an engine

failure.

• Place generator on a level surface (not to exceed 15° in any

direction).

• Clean area around oil fill and remove oil fill cap.

• Slowly fill engine with oil through the oil fill opening until it

reaches the full mark. Stop filling occasionally to check oil

level. Engine oil is full when level is up to the threads of the oil

fill plug (Figure 9).

• Install oil fill cap and finger tighten securely.

• Check engine oil level before starting each time thereafter.

Operation

Figure 9 - Oil Level

2.8.2 ADDING GASOLINE





Never fill fuel tank indoors. Never fill fuel tank

when engine is running or hot. Avoid spilling

gasoline on a hot engine. Allow engine to cool

entirely before filling fuel tank.





Do not overfill the fuel tank. Always leave room

for fuel expansion. If the fuel tank is overfilled,

fuel can overflow onto a hot engine and cause

FIRE or EXPLOSION. Wipe up any spilled fuel

immediately.





Do not light a cigarette or smoke when filling

the fuel tank. Gasoline is highly FLAMMABLE

and its vapors are EXPLOSIVE.

• Use regular UNLEADED gasoline with the generator engine. Do

not use premium gasoline. Do not mix oil with gasoline.

• Do not use gasoline with more than 10% alcohol such as E85

or Methanol.

• Clean area around fuel fill cap, remove cap.

• Slowly add unleaded regular gasoline to fuel tank. Fill to bottom

of screen filter. Be careful not to overfill (Figure 10).

• Install fuel cap and wipe up any spilled gasoline.

Figure 10 – Fuel Fill Level

DO NOT FILL

ABOVE LIP!

IMPORTANT: It is important to prevent gum deposits from forming

in fuel system parts such as the carburetor, fuel hose or tank

during storage. Alcohol-blended fuels (called gasohol, ethanol

or methanol) can attract moisture, which leads to separation and

formation of acids during storage. Acidic gas can damage the fuel

system of an engine while in storage. To avoid engine problems,

the fuel system should be emptied before storage of 30 days or

longer. See the "Storage" section. Never use engine or carburetor

cleaner products in the fuel tank as permanent damage may occur.

2.9 TO START THE ENGINE



Never start or stop engine with electrical

devices plugged into the receptacles AND

devices turned on.

• Unplug all electrical loads from the unit's receptacles before

starting the engine.

• Place generator on a level surface (not to exceed 15° in any

direction).

• Open the fuel shut-off valve (Figure 11).

Figure 11 – Fuel Shut-Off Valve

• Slide engine CHOKE knob outward to “Full Choke” position

(Figure 12).

Figure 12 – Choke Operation

Operation

NOTE:

The engine switch must be in the ON position.

• To start manually, firmly grasp the recoil handle and pull slowly

until increased resistance is felt. Pull rapidly up and away to

start engine. Then follow the same choke sequence listed

above.

• When the engine starts, slide choke knob to “1/2 Choke”

position until the engine runs smoothly and then fully in to the

“Run” position. If engine falters, slide choke knob back out to

“1/2 Choke” position until the engine runs smoothly and then

to “Run” position.

NOTE:

If engine fires, but does not continue to run, pull choke knob to

“Full Choke” and repeat starting instructions.



Do not overload the generator. Also, do

not overload individual panel receptacles.

These outlets are protected against overload

with push-to-reset-type circuit breakers. If

amperage rating of any circuit breaker is

exceeded, that breaker opens and electrical

output to that receptacle is lost. Read “Don’t

Overload the Generator” carefully.

2.10 STOPPING THE ENGINE

1. Shut off all loads, then unplug the electrical loads from

generator panel receptacles. Never start or stop the engine

with electrical devices plugged in and turned on.

2. Let engine run at no-load for several minutes to stabilize the

internal temperatures of engine and generator.

3. Move Run/Stop switch to “Off” position.

4. Close fuel valve.

2.11 LOW OIL PRESSURE SHUTDOWN SYSTEM

The engine is equipped with a low oil pressure sensor that shuts

down the engine automatically when the oil pressure drops below

5 psi. A delay built into the low oil shutdown system allows oil

pressure to build during starting. The delay allows the engine to

run for about 10 seconds before sensing oil pressure. If the engine

shuts down by itself and the fuel tank has enough gasoline, check

engine oil level.

2.11.1 RESTARTING

If trying to restart the engine within 10 seconds after a low oil

pressure shut down, the engine may NOT start. The system needs

5 to 10 seconds to reset.

If the engine is restarted after such a shutdown and the low oil

pressure has not been corrected (i.e. adding oil), the engine will

run for about 10 seconds as described above and then stop.

3.1 PERFORMING SCHEDULED MAINTENANCE

It is important to perform service as specified in the Maintenance

Schedule for proper generator operation, and to ensure that the

generator complies with the applicable emission standards for the

duration of its useful life. Service and repairs may be performed by

any capable person or repair shop. Additionally, emissions critical

maintenance must be performed as scheduled in order for the

Emissions Warranty to be valid. Emissions critical maintenance

consists of servicing the air filter and spark plugs in accordance

with the Maintenance Schedule.

3.2 MAINTENANCE SCHEDULE

Follow the calendar intervals. More frequent service is required

when operating in adverse conditions noted below.

Check Oil Level At Each Use

Change Oil and Oil Filter‡ *Every Season/Every 100 Hours

Clean Spark Arrestor Screen Every Season/Every 100 Hours

Service Air Filter **Every Season/Every 200 Hours

Replace Spark Plug Every Season/Every 200 Hours

‡ Change oil after first 30 hours of operation then every season.

* Change oil and oil filter every month when operating under heavy load or in high

temperatures.

** Clean more often under dirty or dusty operating conditions. Replace air filter

parts if very dirty.

3.3 PRODUCT SPECIFICATIONS

3.3.1 GENERATOR SPECIFICATIONS

Rated Max. Power ...................................................................3.6 kW**

Surge Power ...............................................................................4.5 kW

Rated AC Voltage ......................................................................120/240

Rated Max AC Load

Current @ 240V .............................................................15.0 Amps**

Current @ 120V .............................................................30.0 Amps**

Rated Frequency .................................................... 60 Hz @ 3600 RPM

Phase ................................................................................Single Phase

** Maximum wattage and current are subject to, and limited by, such factors

as fuel Btu content, ambient temperature, altitude, engine condition, etc..

Maximum power decreases about 3.5% for each 1,000 feet above sea level;

and will also decrease about 1% for each 6° C (10° F) above 16° C (60° F)

ambient temperature.

3.3.2 ENGINE SPECIFICATIONS

Rated Horsepower @ 3600 RPM .........................................................6

Displacement ............................................................................216.5cc

Spark Plug Type ...................................Champion RC14YC or Equivalent

Spark Plug Gap ............................................... 0.030 inch or (0.76 mm)

Gasoline Capacity ......................................................... 4.5 U.S. gallons

Oil Type....................................See Chart in "Adding Engine Oil" Section

Oil Capacity ................................................ w/ Filter Change = 0.8 Qts.

Run Time/Fuel Consumption-1/2 Load

3.6 kW .............................................. 14 Hours / .35 gallons per hour

Class I Emission Certified

Maintenance

3.3.3 EMISSIONS INFORMATION

The Environmental Protection Agency (and California Air Resource

Board for generators certified to CA standards) require(s) that

this generator comply with exhaust and evaporative emission

standards. Locate the emissions compliance decal on the engine

to determine what standards the generator meets. This generator

is certified to operate on gasoline. The emission control system

consists of the following:

• Air Induction System

– Intake Pipe/Manifold

– Air Cleaner

• Fuel System

– Carburetor

– Fuel Tank/Cap

– Fuel Lines

– Evaporative Vent Lines

– Carbon Canister (for CA engines only)

• Ignition System

– Spark Plug

– Ignition Module

• Exhaust System

– Exhaust Manifold/Muffler

3.4 GENERAL RECOMMENDATIONS

The warranty of the generator does not cover items that have been

subjected to operator abuse or negligence. To receive full value

from the warranty, the operator must maintain the generator as

instructed in this manual.

Some adjustments will need to be made periodically to properly

maintain the generator.

All adjustments in the Maintenance section of this manual should

be made at least once each season. Follow the requirements in the

"Maintenance Schedule".

NOTE:

Once a year replace the spark plug and replace the air filter.

A new spark plug and clean air filter assure proper fuel-air

mixture and help the engine run better and last longer.

3.4.1 GENERATOR MAINTENANCE

Operate and store the unit in a clean dry environment where it will

not be exposed to excessive dust, dirt, moisture or any corrosive

vapors. Cooling air slots in the generator must not become clogged

with snow, leaves, or any other foreign material.

Check the cleanliness of the generator frequently and clean when

dust, dirt, oil, moisture or other foreign substances are visible on

its exterior surface.



Never insert any object or tool through the air

cooling slots, even if the engine is not running.

NOTE:

DO NOT use a garden hose to clean generator. Water can

enter the engine fuel system and cause problems. In addition,

if water enters the generator through cooling air slots, some

water will be retained in voids and crevices of the rotor

and stator winding insulation. Water and dirt buildup on the

generator internal windings will eventually decrease the

insulation resistance of these windings.

3.4.2 TO CLEAN THE GENERATOR

• Use a damp cloth to wipe exterior surfaces clean.

• A soft, bristle brush may be used to loosen caked on dirt, oil, etc.

• A vacuum cleaner may be used to pick up loose dirt and debris.

• Low pressure air (not to exceed 25 psi) may be used to

blow away dirt. Inspect cooling air slots and openings on the

generator. These openings must be kept clean and unobstructed.

3.4.3 ENGINE MAINTENANCE



When working on the generator, always

disconnect spark plug wire from spark plug and

keep the wire away from the spark plug.

3.4.4 CHECKING OIL LEVEL

See the “BEFORE STARTING THE GENERATOR” section for

information on checking the oil level. The oil level should be

checked before each use, or at least every eight hours of operation.

Keep the oil level maintained.

3.4.5 CHANGING THE OIL AND OIL FILTER

Change the oil and filter after the first 30 hours of operation.

Change the oil every 100 hours or every season thereafter. If

running this unit under dirty or dusty conditions, or in extremely

hot weather, change the oil more often.



Hot oil may cause burns. Allow engine to

cool before draining oil. Avoid prolonged

or repeated skin exposure with used oil.

Thoroughly wash exposed areas with soap.

Use the following instructions to change the oil after the engine

cools down:

1. Clean area around oil drain plug.

2. Remove oil drain plug from engine and oil fill plug to drain oil

completely into a suitable container.

3. When oil has completely drained, install oil drain plug and

tighten securely.

4. Place a suitable container beneath the oil filter and turn filter

counterclockwise to remove. Discard according to local

regulations.

5. Coat gasket of new filter with clean engine oil. Turn filter

clockwise until gasket contacts lightly with filter adapter. Then

tighten an additional 3/4 turn.

Maintenance

6. Fill engine with recommended oil. (See “Before Starting the

Generator” for oil recommendations).

7. Wipe up any spilled oil.

8. Dispose of used oil at a proper collection center.

3.4.6 REPLACING THE SPARK PLUG

Use Champion RC14YC spark plug or equivalent. Replace the

plug every 200 hours. This will help the engine start easier and

run better.

1. Stop the engine and pull the spark plug wire off of the spark

plug.

2. To gain access, remove the four (4) screws and remove the

side panel.

3. Clean the area around the spark plug and remove it from the

cylinder head.

4. Set the spark plug's gap to .76 mm (0.030 in.). Install the

correctly gapped spark plug into the cylinder head (Figure 13).

5. Push the boot firmly on the spark plug and install side panel.

Figure 13 - Spark Plug Gap

3.5 SERVICE AIR FILTER

The engine will not run properly and may be damaged if using a

dirty air filter. Clean or replace the air filter paper filter every 200

hours or once a year (Figure 14). Clean or replace more often if

operating under dusty conditions.

To clean or replace paper air filter:

1. Remove air filter cover; then remove the paper filter.

2. Clean paper filter by tapping it gently on a solid surface. If the

filter is too dirty, replace it with a new one. Dispose of the old

filter properly.

3. Clean air filter cover, then insert new paper filter into the base

of the air filter. Re-install air filter cover.

NOTE:

To order a new air filter, please contact the nearest authorized

service center at 1-888-436-3722.

Figure 14 – Air Filter

Base

Cover

Filter

3.6 CLEAN SPARK ARRESTOR SCREEN

The engine exhaust muffler has a spark arrestor screen. Inspect

and clean the screen every 100 hours or at least once each year

(Figure 15). If unit is used regularly, inspect and clean more often.



If using the generator on any forest-covered,

brush-covered or grass-covered unimproved

land, it must be equipped with a spark arrestor.

The spark arrestor must be maintained in good

condition by the owner/operator.

Clean and inspect the spark arrestor when the engine is at ambient

temperature as follows:

1. Insert a flat blade screwdriver through the slot on the side of

the muffler heat shield to access the spark arrestor clamp.

Loosen the clamp and remove the spark arrestor screen from

the muffler.

2. Inspect screen and replace if torn, perforated or otherwise

damaged. DO NOT USE a defective screen. If screen is not

damaged, clean it with commercial solvent.

3. Replace the spark arrestor and tighten the clamp.

Maintenance

Figure 15 — Spark Arrestor Screen

INSERT SCREWDRIVER

THROUGH SLOT IN HEAT

SHIELD TO ACCESS

ARRESTOR SCREEN CLAMP

ARRESTOR

SCREEN CLAMP

SPARK

ARRESTOR

SCREEN

3.7 GENERAL

The generator should be started at least once every 30 days and

be allowed to run at least 30 minutes. If this cannot be done and

the unit must be stored for more than 30 days, use the following

information as a guide to prepare it for storage.





NEVER store engine with fuel in tank indoors

or in enclosed, poorly ventilated areas where

fumes may reach an open flame, spark or pilot

light as on a furnace, water heater, clothes

dryer or other gas appliance.



Allow unit to cool entirely before storage.

3.8 LONG TERM STORAGE

It is important to prevent gum deposits from forming in essential

fuel system parts such as the carburetor, fuel hose or tank during

storage. Also, experience indicates that alcohol-blended fuels

(called gasohol, ethanol or methanol) can attract moisture, which

leads to separation and formation of acids during storage. Acidic

gas can damage the fuel system of an engine while in storage.

To avoid engine problems, the fuel system should be emptied

before storage of 30 days or longer, as follows:

1. Remove all gasoline from the fuel tank.





Drain fuel into approved container outdoors,

away from open flame. Be sure engine is cool.

Do not smoke in the vicinity or light a cigarette.

2. Start and run engine until engine stops from lack of fuel

3. Allow the engine to cool to the touch and then drain the oil

from the crankcase. Refill with the recommended grade.

4. Remove spark plug and pour about 1/2 ounce (15 ml) of

engine oil into the cylinder. Cover spark plug hole with rag. Pull

the recoil starter a couple times to lubricate the piston rings

and cylinder bore.



Avoid spray from the spark plug hole when

cranking engine.

5. Install and tighten the spark plug. Do not connect the spark

plug wire.

6. Clean the generator outer surfaces. Check that cooling air

slots and openings on generator are open and unobstructed.

7. Store the unit in a clean, dry place.

3.9 OTHER STORAGE TIPS

• Do not store gasoline from one season to another.

• Replace the gasoline can if it starts to rust. Rust and/or dirt in

the gasoline will cause problems with the carburetor and fuel

system.

• If possible, store the unit indoors, in a garage or shed, and

cover it to give protection from dust and dirt. BE SURE TO

EMPTY THE FUEL TANK.

• If it is not practical to empty the fuel tank and the unit is to

be stored for some time, use a commercially available fuel

stabilizer added to the gasoline to increase the life of the

gasoline.

• Cover the unit with a suitable protective cover that does not

retain moisture.



NEVER cover the generator while engine and

exhaust area are warm. Allow unit to cool

entirely.

Maintenance

PROBLEM CAUSE CORRECTION

Engine is running, but no AC output

is available.

1. Circuit breaker is open.

2. Poor connection or defective cord set.

3. Connected device is bad.

4. Fault in generator.

5. GFCI trips the 20 Amp outlets.

1. Reset circuit breaker.

2. Check and repair.

3. Connect another device that is in good condition.

4. Contact Authorized Service Facility.

5. Repair the "short" and reset the GFCI.

Engine runs good but bogs down

when loads are connected.

1. Short circuit in a connected load.

2. Generator is overloaded.

3. Engine speed is too slow.

4. Shorted generator circuit.

1. Disconnect shorted electrical load.

2. See “Don’t Overload the Generator” .

3. Contact Authorized Service Facility.

4. Contact Authorized Service Facility.

Engine will not start; or starts and

runs rough.

1. Fuel shut-off is OFF.

2. Dirty air filter.

3. Out of gasoline.

4. Stale gasoline.

5. Spark plug wire not connected to spark plug.

6. Bad spark plug.

7. Water in gasoline.

8. Over-choking.

9. Low oil level.

10. Excessive rich fuel mixture.

11. Intake valve stuck open or closed.

12. Engine has lost compression.

1. Turn Fuel shut-off ON.

2. Clean or replace air filter.

3. Fill fuel tank.

4. Drain fuel tank and fill with fresh fuel.

5. Connect wire to spark plug.

6. Replace spark plug.

7. Drain fuel tank; fill with fresh fuel.

8. Put choke knob to No Choke position.

9. Fill crankcase to proper level.

10. Contact Authorized Service Facility.

11. Contact Authorized Service Facility.

12. Contact Authorized Service Facility.

Engine shuts down during

operation.

1. Out of gasoline.

2. Low oil level.

3. Fault in engine.

1. Fill fuel tank.

2. Fill crankcase to proper level.

3. Contact Authorized Service Facility.

Engine lacks power. 1. Load is too high.

2. Dirty air filter.

3. Engine needs to be serviced.

1. See “Don’t Overload the Generator”.

2. Replace air filter.

3. Contact Authorized Service Facility.

Engine “hunts” or falters. 1. Choke is opened too soon.

2. Carburetor is running too rich or too lean.

1. Move choke to halfway position until engine runs

smoothly.

2. Contact Authorized Service Facility.

4.1 TROUBLESHOOTING GUIDE

Troubleshooting

Notes

Warranty

U.S. EPA EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The United States Environmental Protection Agency (EPA) and Generac Power Systems, Inc. (Generac) are pleased to explain the Emission Control

System Warranty (ECS Warranty) on your new 2011 and later equipment. New equipment that use small spark-ignited engines must be designed, built,

and equipped to meet stringent anti-smog standards for the federal government. Generac will warrant the emission control system on your equipment

for the period of time listed below provided there has been no abuse, neglect, unapproved modification or improper maintenance of your equipment.

The emission control system on this equipment includes all components whose failure would increase the emissions of any regulated pollutant. These

components are listed in the Emissions Information section of this manual.

MANUFACTURER’S WARRANTY COVERAGE:

This ECS Warranty is valid for two years, or for the same period as specified in the Generac Limited Warranty, whichever is longer. For equipment with

hour meters, the warranty period is a number of hours equal to half the Useful Life to which the equipment is certified, or the warranty period specified

above in years, whichever is less. The Useful Life can be found on the Emission Control Label on the engine. If, during such warranty period, any

emission-related part on your equipment is found to be defective in materials or workmanship, repairs or replacement will be performed by a Generac

Authorized Warranty Service Dealer.

OWNER'S WARRANTY RESPONSIBILITIES:

As the equipment owner, you are responsible for the completion of all required maintenance as listed in your factory supplied Owner's Manual. For

warranty purposes, Generac recommends that you retain all receipts covering maintenance on your generator, but Generac cannot deny warranty

solely due to the lack of receipts.

You should be aware that Generac may deny any and/or all warranty coverage or responsibility if your equipment, or a part/component thereof, has

failed due to abuse, neglect, improper maintenance, or unapproved modifications.

You are responsible for contacting a Generac Authorized Warranty Dealer as soon as a problem occurs. The warranty repairs should be

completed in a reasonable amount of time, not to exceed 30 days.

Warranty service can be arranged by contacting either your selling dealer or a Generac Authorized Warranty Service Dealer. To locate the Generac

Authorized Warranty Service Dealer nearest you, call our toll free number below, or email [email protected].

1-800-333-1322

IMPORTANT NOTE: This warranty statement explains your rights and obligations under the Emission Control System Warranty, which is provided to

you by Generac pursuant to federal law. See also the "Generac Limited Warranties for Generac Power Systems, Inc.," which is enclosed herewith on a

separate sheet, also provided to you by Generac. Note that this warranty shall not apply to any incidental, consequential or indirect damages caused

by defects in materials or workmanship or any delay in repair or replacement of the defective part(s). This warranty is in place of all other warranties,

expressed or implied. Specifically, Generac makes no other warranties as to the merchantability or fitness for a particular purpose. Any implied

warranties which are allowed by law, shall be limited in duration to the terms of the express warranty provided herein. Some states do not allow

limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

The ECS Warranty applies only to the emission control system of your new equipment. Both the ECS Warranty and the Generac Warranty describe

important rights and obligations with respect to your new engine.

Warranty service can be performed only by a Generac Authorized Warranty Service Facility. When requesting warranty service, evidence must be

presented showing the date of the sale to the original purchaser/owner.

If you have any questions regarding your warranty rights and responsibilities, you should contact Generac at the following address:

ATTENTION WARRANTY DEPARTMENT

GENERAC POWER SYSTEMS, INC.

P.O. BOX 297 • WHITEWATER, WI 53190

Part 1 of 2