Wolf DO3050TEST Guide d'installation

E Series Oven

Installation Guide

SPECIFICATIONS, INSTALLATION, AND MORE

E Series Oven

Contents

2

Important Note

3

Product Information

4

Specifications

12

Installation

E Series Oven

Important Note

To make sure this product is installed and operated safely

and efficiently, take note of the following types of

highlighted information throughout this guide:

IMPORTANT NOTE: Highlights information that is

especially important.

CAUTION

Indicates a situation where minor injury or product

damage may occur if instructions are not followed.

WARNING

States a hazard that may cause serious injury or

death if precautions are not followed.

IMPORTANT NOTE: Throughout this guide, dimensions in

parentheses are millimeters unless otherwise specified.

2

|

English

Product Information

Important product information, including the model and

serial number, are listed on the product rating plate. If

service is necessary, contact Wolf Factory Certified

Service with the model number and serial number. For

the name of the nearest Wolf Factory Certified Service or

for questions regarding the installation, visit the Product

Support section of our website, or call Wolf Customer

Care at 800-222-7820.

The rating plate is located near the bottom trim on the

left. The oven door must be open to view the rating plate.

RATING

PLATE

E Series Oven

Product Information

wolfappliance.com

|

3

Installation Requirements

The oven can be installed in a standard or flush inset

application. If a cooktop is installed above an oven, a

minimum of

1

/

4

" (6) is required between the units. The

location of the electrical supply within the oven opening

may require additional cabinet depth.

Base Support Min

Single Oven 250 lb (115 kg)

Double Oven 400 lb (181 kg)

Finish the edges of the opening. They may be visible

when the door is open.

For standard installations, the face trim overlaps stiles and

rails.

Trim Overlap Dimension

Top 1" (25)

Bottom 0"

Sides

11

/

16

" (18)

For flush inset installations, a minimum

1

/

8

" (3) reveal is

required on all sides. To ensure consistent reveals, each

corner of the opening must be exactly 90°.

Dual Installation

Two 30" single ovens can be installed side by side in a

standard or flush inset application. A dual installation kit is

required. To maintain appropriate airflow, the ovens must

be installed into one opening. Any cosmetic or structural

material placed between the ovens will impede airflow

and is not recommended. Refer to the illustrations on the

following pages.

The dual installation kit is available through an authorized

Wolf dealer. For local dealer information, visit the locator

section of our website subzero-wolf.com.

Specifications

Installation Requirements

4

|

English

Electrical Requirements

Installation must comply with all applicable electrical

codes.

Locate the electrical supply flush with the back wall and

within the shaded area shown in the illustrations on pages

6-11. For ease of installation, the electrical supply for the

oven can be placed in an adjacent cabinet within reach of

the conduit.

Performance may be compromised if the electrical supply

is less than 240 volts.

The oven is supplied with a conduit consisting of two

insulated hot lead conductors and a bare ground

conductor. The wiring diagram covering the control

circuit is provided with the oven.

ELECTRICAL REQUIREMENTS-Single Oven

Electrical Supply

grounded, 240/208 VAC,

60Hz

Service 30 amp dedicated circuit

Conduit 4' (1.2 m)

Total Amps 22

Max Connected Load 5.4 kW

ELECTRICAL REQUIREMENTS-Double Oven

Electrical Supply

grounded, 240/208 VAC,

60Hz

Service 50 amp dedicated circuit

Conduit 5' (1.5 m)

Total Amps 45

Max Connected Load 10.8 kW

Specifications

Electrical Requirements

wolfappliance.com

|

5

30" Single Oven Standard

Installation

28

1

/2" (724)

OPENING WIDTH

E

5"

(127)

E

4"

(102)

FRONT VIEWSIDE VIEW

NOTE: Location of electrical supply within opening may require additional cabinet depth.

23

1

/4" (591)

OPENING

DEPTH

TOP VIEW

27

1

/2"

(699)

OPENING

HEIGHT

Specifications

30" Single Oven Standard

Installation

6

|

English

30" Single Oven Flush Inset

Installation

30

1

/8" (765)

FLUSH INSET WIDTH**

*Shaded areas will be visible and should be finished to match cabinetry.

**Dimension provides minimum reveals.

NOTE: Location of electrical supply within opening may require additional cabinet depth.

28

3

/4"

(730)

FLUSH INSET

HEIGHT**

E

5"

(127)

4"

(102)

FRONT VIEWSIDE VIEW

1

/8" (29)

1

/8" (3)

13

/16" (21)

24" (610)

FLUSH INSET

DEPTH

7

/8" (22)

TOP VIEW

E

FINISHED

CLEATS*

Specifications

30" Single Oven Flush Inset

Installation

wolfappliance.com

|

7

30" Double Oven Standard

Installation

28

1

/2" (724)

OPENING WIDTH

E

5"

(127)

4"

(102)

E

FRONT VIEWSIDE VIEW

NOTE: Location of electrical supply within opening may require additional cabinet depth.

49

7

/8"

(1267)

OPENING

HEIGHT

23

1

/4" (591)

OPENING

DEPTH

17" (432)

TYPICAL

TOP VIEW

Specifications

30" Double Oven Standard

Installation

8

|

English

30" Double Oven Flush

Inset Installation

30

1

/8" (765)

FLUSH INSET WIDTH**

E

5"

(127)

4"

(102)

FRONT VIEWSIDE VIEW

51

1

/8"

(1299)

FLUSH INSET

HEIGHT**

1

/8" (29)

1

/8" (3)

13

/16" (21)

24" (610)

FLUSH INSET

DEPTH

17" (432)

TYPICAL

TOP VIEW

E

FINISHED

CLEATS*

*Shaded areas will be visible and should be finished to match cabinetry.

**Dimension provides minimum reveals.

NOTE: Location of electrical supply within opening may require additional cabinet depth.

7

/8" (22)

Specifications

30" Double Oven Flush

Inset Installation

wolfappliance.com

|

9

30" Single Oven Dual

Standard Installation

E

5"

(127)

E E

4"

(102)

E

5"

(127)

4"

(102)

FRONT VIEWSIDE VIEW

NOTE: Location of electrical supply within opening may require additional cabinet depth. A dual installation kit is required for this installation.

23

1

/4" (591)

OPENING

DEPTH

TOP VIEW

27

1

/2"

(699)

OPENING

HEIGHT

58

1

/2" (1486)

OPENING WIDTH

Specifications

30" Single Oven Dual

Standard Installation

10

|

English

30" Single Oven Dual Flush

Inset Installation

E

5"

(127)

4"

(102)

E

5"

(127)

4"

(102)

FRONT VIEWSIDE VIEW

*1" (25) minimum depth. Shaded areas will be visible and should be finished to match cabinetry.

**Dimension provides minimum reveals.

NOTE: Location of electrical supply within opening may require additional cabinet depth. A dual installation kit is required for this installation.

28

3

/4"

(730)

FLUSH INSET

HEIGHT**

1

/8" (29)

1

/8" (3)

13

/16" (21)

24" (610)

FLUSH INSET

DEPTH

7

/8" (22)

60

1

/8" (1527)

FLUSH INSET WIDTH**

TOP VIEW

EE

FINISHED

CLEATS*

Specifications

30" Single Oven Dual Flush

Inset Installation

wolfappliance.com

|

11

Preparation

Before moving the oven, protect any finished flooring and

secure the oven door(s) closed to prevent damage.

Use an appliance dolly to move the oven near the

opening. Place the appliance dolly on the side or back to

prevent damage. Remove and recycle packing materials.

Do not lift or carry the oven by the door handle.

Oven Door Removal

To lighten the load, the oven door(s) can be removed.

Remove only if necessary. Door removal should be done

only by a certified installer or service technician. Do not

lift or carry the oven door by the door handle.

To remove, open the door completely. Rotate both hinge

locks back completely, remove the screw closest to the

hinge on both sides of the door, and pull the door

forward.

To install, slide the door onto the hinges. Rotate the hinge

locks forward completely and install the screws.

HINGE

LOCK

SCREW

Electrical Connection

WARNING

Verify that power is disconnected from the electrical

box before proceeding.

If the electrical supply is located in the opening, electrical

connection must be made prior to placing the oven in the

opening. If the electrical supply is in an adjacent cabinet,

electrical connection can be made after placing the oven

in the opening. The conduit on the back of the unit allows

for a 3-wire or 4-wire installation.

1

Connect the black appliance wire to the black (L1)

power supply.

2

Connect the red appliance wire to the red (L2) power

supply.

3

Connect the bare appliance wire to the green/ground

wire.

4

For a four-wire system, install a wire nut on the white/

neurtral wire.

Installation

Place the oven in the opening and slide into position. To

ensure adequate depth for proper installation, the conduit

must fit into the recessed area along the rear edge of the

oven.

Locate the mounting hole in each side trim. Drill 1/16" (2)

pilot holes and install #6 x 3/4" screws.

Remove and recycle packing materials including the

white protective material behind each rack guide

mounting location.

Installation

Preparation

12

|

English

Door Alignment

To adjust the door, loosen the nuts on both sides of the

door, manually adjust the bottom of the door side to side,

and tighten the nuts.

NUT

Troubleshooting

IMPORTANT NOTE: If the range does not operate properly,

follow these troubleshooting steps:

• Verify electrical power is supplied to the oven.

• Verify proper electrical connections.

• If the oven does not operate properly, contact Wolf

Factory Certified Service. Do not attempt to repair the

oven. Wolf is not responsible for service required to

correct a faulty installation.

Installation

Door Alignment

wolfappliance.com

|

13

Horno de la serie E

Contenido

14

Aviso importante

15

Información del producto

16

Especificaciones

24

Instalación

Horno de la serie E

Aviso importante

Para asegurarse de que este producto se instale y opere

de forma segura y eficiente, tome nota de los siguientes

tipos de información resaltada en este manual:

NOTA IMPORTANTE:: Señala la información que es

especialmente importante.

PRECAUCIÓN

Indica una situación en la que se pueden sufrir

lesiones leves o provocar daños al producto, si no se

siguen las instrucciones.

ADVERTENCIA

Indica peligro de que se produzcan heridas graves o

incluso la muerte si no se siguen las precauciones.

NOTA IMPORTANTE:: En toda esta guía, las dimensiones

entre paréntesis son milímetros, a menos que se

especifique lo contrario.

14

|

Español

Información del producto

La información importante del producto, incluidos el

modelo y el número de serie de la unidad, se encuentra

en la placa de datos del producto. Si es necesario realizar

algún servicio, póngase en contacto con el servicio

certificado de fábrica de Wolf y tenga a mano el número

de modelo y el número de serie. Para obtener los datos

del centro de servicio certificado de fábrica de Wolf más

cercano o si tiene preguntas acerca de la instalación,

visite la sección de soporte del producto en nuestra

página de Internet o llame a la línea de atención al cliente

de Wolf al 800-222-7820.

La placa de datos se encuentra cerca de la moldura

inferior en la izquierda. La puerta del horno debe estar

abierta para ver la placa de datos.

Horno de la serie E

Información del producto

wolfappliance.com

|

15

Requisitos de instalación

El horno se puede instalar en una aplicación estándar o

empotrable. Si se instala una estufa sobre un horno, se

requiere un espacio mínimo de

1

/

4

" (6) entre las unidades.

Es posible que la ubicación del suministro eléctrico al

interior de la abertura del horno requiera de un gabinete

de mayor profundidad.

Soporte de la base Mín

Horno sencillo 250 lb (115 kg)

Horno doble 400 lb (181 kg)

Dé el acabado a los bordes de la abertura. Pueden ser

visibles cuando la puerta está abierta.

Para instalaciones estándar, el ribete frontal se superpone

a los largueros y las guías.

Superposición del ribete Dimensión

Parte superior 1" (25)

Parte inferior 0" (76.2 cm)

Laterales

11

/

16

" (18)

Para las instalaciones empotrables se requiere un margen

mínimo de

1

/

8

" (3) en todos los lados. Para asegurar

márgenes consistentes, cada esquina de la abertura debe

tener exactamente 90º.

Instalación doble

Se pueden instalar dos hornos sencillos de 30”, uno al

lado del otro, en una aplicación estándar o empotrable.

Se requiere kit de instalación doble. Para mantener un

flujo de aire adecuado, los hornos se deben instalar en

una sola abertura. Cualquier elemento cosmético o

estructural que se coloque entre los hornos obstruirá el

flujo de aire y, por lo tanto, no se recomienda. Consulte

las ilustraciones de las páginas siguientes.

El kit de instalación doble está disponible a través de un

distribuidor autorizado de Wolf. Para obtener más

información acerca de los distribuidores locales, consulte

la sección de ubicador en nuestra página web subzero-

wolf.com.

Especificaciones

Requisitos de instalación

16

|

Español

Requisitos eléctricos

REQUISITOS ELÉCTRICOS- Horno sencillo

Suministro eléctrico

Con conexión a tierra,

240/208 V CA, 60Hz

Servicio

Circuito dedicado de 30

amperes

Conducto 4' (1.2 m)

Total de amperes 22

Carga máxima conectada 5.4 kW

REQUISITOS ELÉCTRICOS- Horno doble

Suministro eléctrico

Con conexión a tierra,

240/208 V CA, 60Hz

Servicio

Circuito dedicado de 50

amperes

Conducto 5' (1.5 m)

Total de amperes 45

Carga máxima conectada 10.8 kW

Especificaciones

Requisitos eléctricos

wolfappliance.com

|

17

Instalación estándar de

horno sencillo de 30”

28

1

/2" (724)

ANCHO DE LA ABERTURA

E

5"

(127)

E

4"

(102)

VISTA FRONTALVISTA LATERAL

NOTA: es posible que la ubicación del suministro eléctrico al interior de la abertura requiera de un gabinete de mayor profundidad.

23

1

/4" (591)

PROFUNDIDAD DE

LA ABERTURA

VISTA SUPERIOR

27

1

/2"

(699)

ALTURA DE

LA ABERTURA

Especificaciones

Instalación estándar de

horno sencillo de 30”

18

|

Español

Instalación empotrable de

horno sencillo de 30”

*Las áreas sombreadas serán visibles y se les debe dar un acabado que combine con los gabinetes.

**La dimensión especifica los márgenes mínimos.

NOTA: es posible que la ubicación del suministro eléctrico al interior de la abertura requiera de un gabinete de mayor profundidad.

28

3

/4"

(730)

ALTURA DE

LA INSTALACIÓN

EMPOTRABLE**

E

5"

(127)

4"

(102)

1

/8" (29)

1

/8" (3)

13

/16" (21)

24" (610)

PROFUNDIDAD DE

LA INSTALACIÓN

EMPOTRABLE

7

/8" (22)

E

CORNAMUSAS

TERMINADAS*

30

1

/8" (765)

ANCHO DE LA

INSTALACIÓN EMPOTRABLE**

VISTA FRONTALVISTA LATERAL

VISTA SUPERIOR

Especificaciones

Instalación empotrable de

horno sencillo de 30”

wolfappliance.com

|

19

Instalación estándar de

horno doble de 30”

28

1

/2" (724)

ANCHO DE LA ABERTURA

E

5"

(127)

4"

(102)

E

VISTA FRONTALVISTA LATERAL

NOTA: es posible que la ubicación del suministro eléctrico al interior de la abertura requiera de un gabinete de mayor profundidad.

49

7

/8"

(1267)

ALTURA DE

LA ABERTURA

23

1

/4" (591)

PROFUNDIDAD DE

LA ABERTURA

17" (432)

TÍPICO

VISTA SUPERIOR

Especificaciones

Instalación estándar de

horno doble de 30”

20

|

Español

La page est en cours de chargement...

Wolf DO3050TEST Guide d'installation

Ce manuel convient également à

Wolf DO3050TEST Guide d'installation

dans d''autres langues

Documents connexes

Autres documents