Generac XP6500E 0059340 Manuel utilisateur

www.generac.com or 1-888-436-3722

Owner's Manual

XP Series Portable Generator



DEADLY EXHAUST FUMES! ONLY use OUTSIDE far away

from windows, doors and vents!



NOT INTENDED FOR USE IN CRITICAL LIFE SUPPORT

APPLICATIONS.



SAVE this Manual. Provide this manual to any operator of

the generator.

Introduction ............................................................. 1

Read this Manual Thoroughly ................................. 1

Safety Rules ........................................................... 1

Standards Index .............................................................3

General Information ................................................ 4

1.1 Unpacking ......................................................................4

1.1.1 Accessory Box (6.5, 8 & 10kW) ........................4

1.2 Assembly .......................................................................4

1.2.1 Assembling the Wheel Kit ..................................4

1.2.2 Battery Connection (if equipped) ........................4

Operation ................................................................ 5

2.1 Know the Generator .......................................................5

2.1.1 Cold Weather Operation/De-icer .........................8

2.2 Hour Meter - With Reset .................................................9

2.3 Connection Plugs ...........................................................9

2.3.1 250 VAC, 20 Amp Duplex Receptacle ................9

2.3.2 120/240 VAC, 30 Amp Receptacle .....................9

2.3.3 120/240 VAC, 50 Amp Receptacle (10kW) ......10

2.3.4 Ground Fault Sensing Module ..........................10

2.3.5 120 VAC, 30 Amp Receptacle ..........................10

2.4 Automatic Idle Control (if equipped)..............................11

2.5 Voltage Selector Switch (3.6 & 6.5kW only) .................11

2.6 How to Use the Generator ............................................11

2.6.1 System Ground ................................................11

2.6.2 Grounding the Generator ..................................12

2.6.3 Connecting Electrical Loads .............................12

2.7 Overload Prevention .....................................................12

2.8 Wattage Reference Guide .............................................12

2.9 Before Starting the Generator .......................................13

2.9.1 Adding Engine Oil ............................................13

2.9.2 Adding Gasoline ...............................................13

2.10 Starting the Engine (electric start only) .........................14

2.11 Starting Pull Start Engines ............................................14

2.12 Stopping the Engine .....................................................14

2.13 Low Oil Level Shutdown System ..................................15

2.14 Charging the Battery (if equipped) ................................15

Maintenance ......................................................... 15

3.1 Performing Scheduled Maintenance .............................15

3.2 Maintenance Schedule .................................................15

3.3 Product Specifications ..................................................16

3.3.1 Generator Specifications ..................................16

3.3.2 Engine Specifications .......................................16

3.3.3 Emissions Information .....................................16

3.4 General Recommendations ...........................................17

3.4.1 Generator Maintenance ....................................17

3.4.2 To Clean the Generator .....................................17

3.4.3 Engine Maintenance .........................................17

3.4.4 Checking Oil Level ...........................................17

3.4.5 Changing the Oil and Oil Filter ..........................17

3.4.6 Replacing the Spark Plug(s) .............................17

3.4.7 Battery Replacement (if equipped) ...................18

3.4.8 Air Filter Replacement ......................................18

3.4.9 Clean Spark Arrestor Screen ............................19

3.4.10 Adjusting Valve Clearance ................................19

3.5 General ........................................................................20

3.6 Long Term Storage .......................................................20

Troubleshooting .................................................... 21

4.1 Troubleshooting Guide ..................................................21

Manual del Usuario............................................... 23

Manuel de l'utilisateur .......................................... 47

(000004)

WARNING

California Proposition 65. Engine exhaust and some of

its constituents are known to the state of California to

cause cancer, birth defects, and other reproductive

harm.

(000005)

WARNING

California Proposition 65. This product contains or

emits chemicals known to the state of California to

cause cancer, birth defects, and other reproductive

harm.

Table of Contents

INTRODUCTION

Thank you for purchasing this model by Generac Power Systems,

Inc. This model is a compact, high performance, air-cooled,

engine driven generator designed to supply electrical power to

operate electrical loads where no utility power is available or in

place of utility due to a power outage.

READ THIS MANUAL THOROUGHLY

If any portion of this manual is not understood, contact the nearest

Authorized Dealer for starting, operating and servicing procedures.

The operator is responsible for proper and safe use of the

equipment. We strongly recommend that the operator read this

manual and thoroughly understand all instructions before using

the equipment. We also strongly recommend instructing other

users to properly start and operate the unit. This prepares them

if they need to operate the equipment in an emergency. Save

these instructions for future reference. If you loan this device

to someone, ALWAYS loan these instructions to the individual

as well.

The generator can operate safely, efficiently and reliably only if it

is properly located, operated and maintained. Before operating or

servicing the generator:

• Become familiar with and strictly adhere to all local, state and

national codes and regulations.

• Study all safety warnings in this manual and on the product

carefully.

• Become familiar with this manual and the unit before use.

The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, therefore, not all inclusive.

If using a procedure, work method or operating technique that the

manufacturer does not specifically recommend, ensure that it is

safe for others. Also make sure the procedure, work method or

operating technique utilized does not render the generator unsafe.

THE INFORMATION CONTAINED HEREIN WAS BASED ON

MACHINES IN PRODUCTION AT THE TIME OF PUBLICATION.

GENERAC RESERVES THE RIGHT TO MODIFY THIS MANUAL AT

ANY TIME.

SAFETY RULES

Throughout this publication, and on tags and decals affixed to the

generator, DANGER, WARNING, CAUTION and NOTE blocks are

used to alert personnel to special instructions about a particular

operation that may be hazardous if performed incorrectly or

carelessly. Observe them carefully. Their definitions are as follows:

(000001)

DANGER

Indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

(000002)

WARNING

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

(000003)

CAUTION

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

NOTE: Notes contain additional information important to a

procedure and will be found within the regular text body of this

manual.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliance with the special

instructions while performing the action or service are essential to

preventing accidents.

Four commonly used safety symbols accompany the DANGER,

WARNING and CAUTION blocks. The type of information each

indicates is as follows:



This symbol points out important safety

information that, if not followed, could

endanger personal safety and/or property of

others.





This symbol points out potential explosion

hazard.



This symbol points out potential fire hazard.



This symbol points out potential electrical

shock hazard.

Introduction

1

GENERAL HAZARDS

• NEVER operate in an enclosed area, in a vehicle, or indoors

EVEN IF doors and windows are open.

• For safety reasons, the manufacturer recommends that the

maintenance of this equipment is carried out by an Authorized

Dealer. Inspect the generator regularly, and contact the nearest

Authorized Dealer for parts needing repair or replacement.

• Operate generator only on level surfaces and where it will not be

exposed to excessive moisture, dirt, dust or corrosive vapors.

(000111)

WARNING

Moving Parts. Keep clothing, hair, and appendages

away from moving parts. Failure to do so could

result in death or serious injury.

• Certain parts of the generator get extremely hot during

operation. Keep clear of the generator until it has cooled to

avoid severe burns.

• Do NOT operate generator in the rain.

• Do not alter the construction of the generator or change

controls which might create an unsafe operating condition.

(000116)

DANGER

Electrocution. Turn utility and emergency

power supplies to OFF before connecting power

source and load lines. Failure to do so will result

in death or serious injury.

• Do not insert objects through unit’s cooling slots.

• When working on this equipment, remain alert at all times.

Never work on the equipment when physically or mentally

fatigued.

• Lifting Warning Hazard: A falling generator can result in death,

bodily injury, and/or property damage. Stand clear of generator.

Lift is designed to carry only the weight of the generator. DO

NOT overload lifting bracket. Apply lifting strap or hook through

lift bar hole(s) only. DO NOT lift while generator is running.

• Never use the generator or any of its parts as a step. Stepping

on the unit can stress and break parts, and may result in

dangerous operating conditions from leaking exhaust gases,

fuel leakage, oil leakage, etc.

• On electric start models, disconnect the POSITIVE (+) battery

cable from the engine starter OR the NEGATIVE (-) battery

cable from the battery terminal, whichever is easier, before

transporting the generator.

NOTE: This generator is equipped with a spark arrestor muffler.

The spark arrestor must be maintained in effective working

order by the owner/ operator. In the State of California, a spark

arrestor is required by law (Section 4442 of the California

Public Resources Code). Other states may have similar laws.

Federal laws apply on federal lands.

EXHAUST & LOCATION HAZARDS

• Never operate in an enclosed area or indoors! NEVER use in

the home, in a vehicle, or in partly enclosed areas such as

garages, EVEN IF doors and windows are open! ONLY use

outdoors and far from open windows, doors, vents, and in an

area that will not accumulate deadly exhaust.

(000103)

DANGER

Asphyxiation. Running engines produce carbon

monoxide, a colorless, odorless, poisonous gas.

Carbon monoxide, if not avoided,

will result in death or serious injury.

• Adequate, unobstructed flow of cooling and ventilating air

is critical to correct generator operation. Do not alter the

installation or permit even partial blockage of ventilation

provisions, as this can seriously affect safe operation of the

generator. The generator MUST be operated outdoors.

• This exhaust system must be properly maintained. Do nothing

that might render the exhaust system unsafe or in noncompliance

with any local codes and/or standards.

• Always use a battery operated carbon monoxide alarm indoors,

installed according to the manufacturer's instructions.

• If you start to feel sick, dizzy, or weak after the generator has

been running, move to fresh air IMMEDIATELY. See a doctor, as

you could have carbon monoxide poisoning.

ELECTRICAL HAZARDS

• The generator produces dangerously high voltage when in

operation. Avoid contact with bare wires, terminals, connections,

etc., while the unit is running, even on equipment connected

to the generator. Ensure all appropriate covers, guards and

barriers are in place before operating the generator.

• Never handle any kind of electrical cord or device while

standing in water, while barefoot or while hands or feet are wet.

DANGEROUS ELECTRICAL SHOCK MAY RESULT.

• The National Electric Code (NEC) requires the frame and external

electrically conductive parts of the generator be properly

connected to an approved earth ground. Local electrical codes

may also require proper grounding of the generator. Consult

with a local electrician for grounding requirements in the area.

Safety Rules

2

• Use a ground fault circuit interrupter in any damp or highly

conductive area (such as metal decking or steel work).

• Do not use worn, bare, frayed or otherwise damaged electrical

cord sets with the generator.

• Before performing any maintenance on the generator, disconnect

the engine starting battery (if equipped) to prevent accidental

start up. Disconnect the cable from the battery post indicated

by a NEGATIVE, NEG or (–) first. Reconnect that cable last.

• In case of accident caused by electric shock, immediately shut

down the source of electrical power. If this is not possible,

attempt to free the victim from the live conductor. AVOID

DIRECT CONTACT WITH THE VICTIM. Use a non-conducting

implement, such as a rope or board, to free the victim from the

live conductor. If the victim is unconscious, apply first aid and

get immediate medical help.

FIRE HAZARDS

(000105)

DANGER

Explosion and Fire. Fuel and vapors are extremely

ammable and explosive. Add fuel in a well

ventilated area. Keep re and spark away. Failure to

do so will result in death or serious injury.

• Never add fuel while unit is running or hot. Allow engine to cool

completely before adding fuel.

• Never fill fuel tank indoors. Comply with all laws regulating

storage and handling of gasoline.

• Do not overfill the fuel tank. Always allow room for fuel

expansion. If tank is over-filled, fuel can overflow onto a hot

engine and cause FIRE or an EXPLOSION. Never store generator

with fuel in tank where gasoline vapors might reach an open

flame, spark or pilot light (as on a furnace, water heater or

clothes dryer). FIRE or EXPLOSION may result. Allow unit to

cool entirely before storage.

• Wipe up any fuel or oil spills immediately. Ensure that no

combustible materials are left on or near the generator. Keep

the area surrounding the generator clean and free from debris

and keep a clearance of five (5) feet (1.5 meters) on all sides to

allow for proper ventilation of the generator.

• Do not insert objects through unit cooling slots.

• NEVER operate the generator if connected electrical devices

overheat, if electrical output is lost, if engine or generator sparks

or if flames or smoke are observed while unit is running.

• Keep a fire extinguisher near the generator at all times.

• DO NOT operate in a hazardous location where there may be a

risk of expolsion of petrol fumes, leaking fuel or explosive dusts.

STANDARDS INDEX

1. National Fire Protection Association (NFPA) 70: The NATIONAL

ELECTRIC CODE (NEC) available from www.nfpa.org

2. National Fire Protection Association (NFPA) 5000: BUILDING

CONSTRUCTION AND SAFETY CODE available from www.

nfpa.org

3. International Building Code available from www.iccsafe.org

4. Agricultural Wiring Handbook available from www.rerc.org ,

Rural Electricity Resource Council P.O. Box 309 Wilmington,

OH 45177-0309

5. ASAE EP-364.2 Installation and Maintenance of Farm Standby

Electric Power available from www.asabe.org, American

Society of Agricultural & Biological Engineers 2950 Niles

Road, St. Joseph, MI 49085

This list is not all inclusive. Check with the Authority Having Local

Jurisdiction (AHJ) for any local codes or standards which may be

applicable to your jurisdiction.

MODEL NO:

SERIAL NO:

Unit ID Location

Safety Rules

3

4

1.1 UNPACKING

• Remove all packaging material.

• Remove separate accessory box.

• Remove carton off the generator.

1.1.1 ACCESSORY BOX

Check all contents (Figure 1). If any parts are missing or damaged

locate an authorized dealer at 1-888-436-3722.

Contents include:

• 2 – Wheels*** • Oil Funnel

• 2 – Hair Pins*** • 2 – Frame Feet***

• Spark Plug (Qty. 2 for 10kW) • 12 Volt Adaptor Plug Charger***

• Air Filter • Spark Plug Wrench

• Oil Filter • Shop Towel

• 4 – Hex Nuts • 2 – Axle Brackets

• 2 – 5/8" Flat Washers (thin)* • 2 – 5/8" Flat Washers (thick)*

• 4 – Bolts x 45mm** • 4 – Bolts x 50mm**

• 2 – 1 Quart SAE 30 Oil Bottles (Qty. 1 for XP4000)

* 6.5 and 8kW Only

** 10kW Only

*** All except 3.6kW

1.2 ASSEMBLY

Read entire Owner's Manual before attempting to assemble or

operate the generator. The generator requires some assembly

prior to using it. If problems arise when assembling the generator,

please call the Generator Helpline at 1-888-436-3722.

1.2.1 ASSEMBLING THE WHEEL KIT

The wheel kit is designed to greatly improve the portability of the

generator. A 10mm and a 13mm wrench are needed to install the

frame feet and axle bracket.

NOTE: The wheel kit is not intended for over-the-road use.

6.5, 8, and 10kW

Refer to Figure 1 and install the feet and wheels as follows:

1. Align the holes in the frame foot to the holes in the frame.

Secure foot with two hex nuts and the 45mm long bolts.

Repeat procedure for other foot.

2. Align the holes in the axle bracket to the holes in the frame.

Secure bracket with 50mm long bolts. Repeat procedure for

other bracket.

3. Slide the axle through the axle bracket holes.

4. Slide on one 5/8” flat washer (thick), the wheel, and a 5/8” flat

washer (thin) onto the axle.

5. Secure with hair pin and repeat for the other wheel.

Figure 1 – Wheel Assembly (6.5, 8 & 10kW)

BOLT X 45MM

LONG

FRAME FOOT

BOLT X 50MM

LONG

HEX NUT

AXLE

BRACKET

HAIR PIN

WHEEL

AXLE

5/8” FLAT WASHER

(THICK)

5/8” FLAT WASHER

(THIN)

1.2.2 BATTERY CONNECTION (IF EQUIPPED)

NOTE: The battery shipped with the generator has been fully

charged. A battery may lose some of its charge when not in use

for prolonged periods of time. If the battery is unable to crank

the engine, plug in the 12V charger included in the accessory

box (see the Charging a Battery section). RUNNING THE

GENERATOR WILL CHARGE THE BATTERY.

The unit has been deliberately shipped with the battery cables

disconnected. You will need two 8mm wrenches to secure the

battery cables.

See Figure 2 for connection details.

1. Cut off cable ties securing the battery cables.

2. First, connect the red battery cable and the red battery charger

wire to the positive (+) battery terminal. Use the supplied

screw and lock nut.

3. Connect the black battery cable and the black battery charger

wire to the negative (-) battery terminal. Use the supplied

screw and lock nut.

4. Make sure all connections are secure. Slide the rubber boots

over the terminals and connection hardware.

General Information

5

Figure 2 - Battery Connections

2.1 KNOW THE GENERATOR

Read the Owner’s Manual and Safety Rules before operating

this generator.

Compare the generator to Figures 3 through 7 to become

familiarized with the locations of various controls and adjustments.

Save this manual for future reference.

1. 120 Volt AC, 20 Amp, Duplex Receptacle – Supplies electrical

power for the operation of 120 Volt AC, 20 Amp, single-phase,

60 Hz electrical lighting, appliance, tool and motor loads.

2. 120/240 Volt AC, 30 Amp Locking Receptacle – Supplies

electrical power for the operation of 120 and/or 240 Volt AC,

30 Amp, single-phase, 60 Hz, electrical lighting, appliance,

tool and motor loads.

3. Circuit Breakers (AC) (6.5 & 8kW) – Each receptacle is

provided with a push-to-reset circuit breaker to protect the

generator against electrical overload.

4. 2-Pole Circuit Breaker (6.5, 8 & 10kW) – this 30 Amp 2-pole

circuit breaker protects the 120/240 Volt locking receptacle.

NOTE: The 10kW uses both a 30 and 42 Amp 2-pole circuit

breaker.

5. 120 Volt AC, 30 Amp Locking Receptacle – Supplies

electrical power for the operation of 120 Volt AC, 30 Amp,

single-phase, 60Hz electrical lighting, appliance, tool and

motor loads.

6. Idle Control – with the switch in the “ON” position, the idle

control runs the engine at normal (high) speeds when there

is an electrical load present and runs the engine at idle (low)

speeds when a load is not present.

7. Fuse (6.5, 8 & 10kW) – this 1.5 Amp fuse protects the

Battery Charger Input jack.

8. Ground Fault Sensing Module – supplies ground fault to

protect electrical power for all receptacles on the control

panel.

9. GFCI Circuit Breaker – Use to reset the full control panel GFCI

electrical system.

10. 10. Voltage Selector Switch (3.6 & 6.5kW only) - Allows the

user to choose between 120/240 volts, or 120 volt only. When

in the 120 volt only position, the total generator output is

available through any of the 120 volt outlets. In the 120/240V

position, receptacles of 120 and 240 volts AC can be used

simultaneously. The voltage selector switch provides the user

with more usable power and improved flexibility.

NOTE: NEVER switch the voltage selector switch with the main

breaker turned on! Doing this can cause arcing and can damage

the generator. First turn off all tools and appliances, turn off the

main circuit, and then operate the voltage selector switch.

11. Hour Meter – Tracks hours of operation and alerts to service

intervals.

12. 120/240 Volt AC, 50 Amp Receptacle (10kW only) - Supplies

electrical power for the operation of 120/240 Volt AC, 42 Amp,

Single Phase, 60 Hz welder or motor loads.

13. Choke Knob – Used when starting a cold engine.

14. Start Switch (6.5, 8, & 10kW) - Use to start engine from the

starter motor.

NOTE: The switch must be in the “On” position when starting

the engine from the recoil starter.

15. 3600 Watt On/Off Switch

16. Spark Plug(s) - See the Maintenance Schedule and Engine

Specification sections for details.

17. Oil Filter - See the Maintenance Schedule and Engine

Specification sections for details.

18. Summer/Winter Valve (10kW Engine ONLY) - Directs hot

engine air to the carburetor when the engine is running in cold

weather conditions. Move the valve to the left when operating

in temperatures above 40 ºF

(4.4 °C). When operating in

temperatures below 40 ºF (4.4 °C), move the summer/winter

valve to the right.

19. Oil Dipstick (10kW ONLY) - Check oil level in the engine.

Always make sure that the oil level is at the FULL mark before

starting engine.

20. Oil Drain – Use to drain engine oil.

21. Oil Fill – Add oil here.

22. Air Filter – Filters intake air as it is drawn into the engine.

23. Recoil Starter (3.6, 6.5 & 8kW) - Use to start engine

manually.

24. Muffler – Quiets the engine.

25. Spark Arrestor – Reduces fire hazards by containing sparks.

26. Grounding Lug – Ground the generator to an approved earth

ground here. See "Grounding the Generator" for details.

27. Handles – Pivot and retract for storage. Press the spring-

loaded button to move handles.

28. Fuel Tank – See generator Specifications for tank capacity.

29. Gas Cap – Fuel fill location.

30. Fuel Gauge – Shows fuel level in tank.

31. Battery (6.5, 8 & 10kW) - Powers the electric starter motor.

32. Battery Charger Input (6.5, 8 & 10kW) - This receptacle

allows the capability to recharge the battery from the adaptor

plug charger.

33. Lifting Device – use to lift and store the generator after use.

See Lifting Safety notes in the beginning of this manual.

Operation

6

Operation

000293

Figure 3 - 3,600 Watt Control Panel

15 11 1 8 9

34

6 5 3 2 10

2 1 5 10

000294

Figure 4 - 6,500 Watt Control Panel

14

13

34

32 7 4 6 3 11 8 9

7

Operation

000296

Figure 6 - 10,000 Watt Control Panel

000295

Figure 5 - 8,000 Watt Control Panel

14

13

34

2 15 11

32 7 46 3 8 9

11

32 1

4

5

12

7

34

3 35

9

8 2

6

8

34. Fuel Shut Off – Valve between fuel tank and carburetor.

35. Fuse (10kW ONLY) - This 5 Amp fuse protects the starting

circuit from overload.

2.1.1 COLD WEATHER OPERATION/DE-ICER

Under certain weather conditions (temperatures below 40 °F (4.4

°C) and a high dew point), the engine may experience icing of the

carburetor and/or the crankcase breather system. To eliminate

this problem, this generator engine is fitted with a winter/summer

valve. This directs hot air into the carburetor during cold weather

operation. Always make sure the winter/summer valve is in the

correct location relative to the weather conditions (Figure 8).

Figure 8 – Winter/Summer Valve

Operation

220cc Engine for

3.6kW Model

410cc Engine for

6.5 & 8kW Models

530cc Engine for

10kW Model

Figure 7 - Generator Controls

9

2.2 HOUR METER - WITH RESET

The Hour Meter tracks hours of operation for scheduled

maintenance (see chart) (Figure 9).

Operation: Push and release the reset button (A) to toggle

between screens. The hours count backwards from the set interval

as shown in the chart.

When the meter reaches 5 hours,the text "CHG OIL" (or "SVC AIR

FILTER" or "CHG PLUG") will flash continually for two minutes.

After this time, the meter will go back to displaying the total hours

of the unit (for 2 minutes). This cyle will repeat for the entire 5

hours.

When the service interval reaches zero hours, the text "NOW"

replaces the hours remaining.

For a new generator for instance, the message will say "CHG OIL"

then flash "in 30". This means that in 30 hours, the oil will need to

be changed. Pressing the button a few more times will bring the

meter back to the screen that shows the total hours run.

Reset: Toggle to the alert that you wish to reset then hold the

button down for 9 seconds. The maintenance hours are reset when

the display shows "0000.0".

NOTE: The hour glass graphic (B) will flash on and off when

the engine is running. This signifies that the meter is tracking

hours of operation.

Figure 9 – Hour Meter

0000.0

000205

2.3 CORD SETS AND CONNECTION PLUGS

2.3.1 120 VAC, 20 AMP, DUPLEX RECEPTACLE

This is a 120 Volt outlet protected against overload by a 20 Amp

push-to-reset circuit breaker (Figure 10). Use each socket to

power 120 Volt AC, single phase, 60 Hz electrical loads requiring

up to a combined 2400 watts (2.4 kW) or 20 Amps of current. Use

only high quality, well-insulated, 3-wire grounded cord sets rated

for 125 Volts at 20 Amps (or greater).

Keep extension cords as short as possible, preferably less than 15

feet (4.5 m) long, to prevent voltage drop and possible overheating

of wires.

Figure 10 - 120 Volt AC, 20 Amp, Duplex Receptacle

2.3.2 120/240 VAC, 30 AMP RECEPTACLE

Use a NEMA L14-30 plug with this receptacle (rotate to lock/

unlock). Connect a suitable 4-wire grounded cord set to the plug

and to the desired load. The cord set should be rated for 250 Volts

AC at 30 Amps (or greater) (Figure 11).

Operation

Hour Meter (With Reset) Chart

Message Frequency of Message Interval Duration of message

CHG OIL Initial break-in period First 30 Hours

ON/OFF for 2 minutes in a 5

hour period

CHG OIL Re-occuring 100 hours

SVC AIR FILTER Re-occuring 200 hours

CHG PLUG Re-occuring 200 hours

A

B

10

Figure 11 - 120/240 VAC, 30 Amp Receptacle

Use this receptacle to operate 120 Volt AC, 60 Hz, single phase

loads requiring up to 3600 watts (3.6 kW) of power at 30 Amps or

240 Volt AC, 60 Hz, single phase loads requiring up to 7200 watts

(7.2 kW) of power at 30 Amps. The outlet is protected by a 2-pole

circuit breaker.

2.3.3 120/240 VAC, 50 AMP RECEPTACLE (10KW)

Use a NEMA 14-50 plug with this receptacle. Connect a 4-wire

cord set rated for 250 Volts AC at 50 Amps to the plug (Figure 12).

Use this receptacle to operate 120/240 Volt AC, 60 Hz electrical

loads requiring up to 10,000 watts (10.0 kW) of power at 41.6

Amps for 240 volts or two independent 120 Volt loads. This

receptacle is protected by a 42 Amp 2-pole circuit breaker.

Figure 12 - 120/240 VAC, 50 Amp Receptacle

50 A

NOTE: Receptacles may be marked with rating values greater

than generator output capacity.

2.3.4 GROUND FAULT SENSING MODULE

This unit is equipped with a ground fault circuit interrupter (GFCI).

This device meets applicable federal, state and local codes. The

ground fault sensing module covers all receptacles.

In the event of a ground fault, the GFCI will trip and quickly stop the

flow of electricity to prevent serious injury.

Definition: The GFCI constantly monitors electricity flowing in a

circuit. If the current flowing through the circuit varies from what

is returning by even a small amount, the GFCI instantly switches

power off by tripping the main circuit breaker on the generator's

control panel.

A GFCI does NOT protect against circuit overloads, short circuits,

or shocks. For example, electric shock can still occur if a person

touches charged electrical wires while standing on a non-

conducting surface, such as a wood floor.

Test the GFCI outlet before each use as follows (Figure 13):

1. Start the generator.

2. Plug a test lamp into duplex receptacle, the lamp should be on.

3. Press the “Test” button on the GFCI to trip the device. The main

breaker should ‘trip’, this being indicated by the movement of

the actuator handle to the ‘OFF’ position.

4. This should stop the flow of electricity making the lamp shut

off. If the main breaker does not ‘trip’, the GFCI is not working

and the generator should not be used. Contact a local service

dealer.

5. To restore the flow of electricity, set the main breaker actuator

handle to the ‘ON’ position. The handles should remain

latched in this position. If it does not, either the GFCI or the

main breaker is failing and should be replaced. Contact a local

service dealer.

6. This GFCI is protected against overload by a 35A/240V main

breaker.

Figure 13 - Testing the GFCI

000361

2.3.5 120 VAC, 30 AMP RECEPTACLE

Use a NEMA L5-30 plug with this receptacle (rotate to lock/

unlock). Connect a suitable 3-wire cord set to the plug and to the

desired load. The cord set should be rated for 250 Volts AC at 30

Amps (or greater) (Figure 14).

Use this receptacle to operate 120 Volt AC, 60Hz, single phase

loads requiring up to 7200 watts (7.2kW) of power at 30 Amps.

The outlet is protected by a 30 Amp push-to-reset circuit breaker.

Operation

11

Operation

Figure 14 - 120 VAC, 30 Amp Receptacle

2.4 AUTOMATIC IDLE CONTROL (IF EQUIPPED)

This feature is designed to greatly improve fuel economy. When

this switch is turned “On,” the engine will only run at its normal

fast governed engine speed when electrical load is connected.

When the load is removed, the engine will run at a reduced speed.

With the switch “Off,” the engine runs at the normal fast engine

speed all the time. Always have the switch OFF when starting and

stopping the engine (Figure 13).

2.5 VOLTAGE SELECTOR SWITCH (3.6 & 6.5KW

ONLY)

Allows the user to choose between 120/240 volts, or 120 volt

only. When in the 120 volt only position, the total generator output

is available through any of the 120 volt outlets. In the 120/240V

position, receptacles of 120 and 240 volts AC can be used

simultaneously. The voltage selector switch provides the user with

more usable power and improved flexibility.

NOTE: NEVER switch the voltage selector switch with the main

breaker turned on! Doing this can cause arcing and can damage

the generator. First turn off all tools and appliances, turn off the

main circuit, and then operate the voltage selector switch.

2.6 HOW TO USE THE GENERATOR

If there are any problems operating the generator, please call the

generator helpline at 1-888-436-3722.



Never operate in an enclosed area or indoors! NEVER

use in the home, in a vehicle, or in partly enclosed areas

such as garages, even if doors and windows are open!

ONLY use outdoors and far from open windows, doors,

vents, and in an area that will not accumulate deadly

exhaust.

(000103)

DANGER

Asphyxiation. Running engines produce carbon

monoxide, a colorless, odorless, poisonous gas.

Carbon monoxide, if not avoided,

will result in death or serious injury.



Adequate, unobstructed flow of cooling and ventilating

air is critical to correct generator operation. Do not

alter the installation or permit even partial blockage of

ventilation provisions, as this can seriously affect safe

operation of the generator. The generator MUST be

operated outdoors.



This exhaust system must be properly maintained. Do

nothing that might render the exhaust system unsafe or

in noncompliance with any local codes and/or standards.



Always use a battery operated carbon monoxide alarm

indoors, installed according to the manufacturer's

instructions.

2.6.1 SYSTEM GROUND

The generator has a system ground that connects the generator

frame components to the ground terminals on the AC output

receptacles.

NOTE: This generator system ground IS bonded to the neutral in

the generator (see applicable unit wiring diagram).

Special Requirements

There may be Federal or State Occupational Safety and Health

Administration (OSHA) regulations, local codes, or ordinances

that apply to the intended use of the generator. Please consult a

qualified electrician, electrical inspector, or the local agency having

jurisdiction:

• In some areas, generators are required to be registered with

local utility companies.

• If the generator is used at a construction site, there may be

additional regulations which must be observed.

12

Operation

Connecting to a Building’s Electrical System through a

Transfer Switch

IMPORTANT: Connections for standby power to a building’s

electrical system must be made by a qualified electrician. The

connection must isolate the generator power from utility power, or

other alternative power sources, and must comply with all related

laws and codes.

NOTE: This generator system ground IS bonded to the neutral in

the generator (see applicable unit wiring diagram).

2.6.2 GROUNDING THE GENERATOR

Local electrical codes may require proper grounding of the unit. For

that purpose, connecting a No. 10 AWG (American Wire Gauge)

stranded copper wire to the grounding lug and to an earth-driven

copper or brass grounding rod (electrode) provides adequate

protection against electrical shock. However, local codes may vary

widely. Consult with a local electrician for grounding requirements

in the area. Proper grounding of the generator will help prevent

electrical shock in the event of a ground fault condition in the

generator or in connected electrical devices. Proper grounding

also helps dissipate static electricity, which often builds up in

ungrounded devices.

Figure 15 - Grounding the Generator

2.6.3 CONNECTING ELECTRICAL LOADS

DO NOT connect 240 Volt loads to 120 Volt receptacles. DO NOT

connect 3-phase loads to the generator. DO NOT connect 50 Hz

loads to the generator.

• Let engine stabilize and warm up for a few minutes after

starting.

• Plug in and turn on the desired 120 or 240 Volt AC, single

phase, 60 Hz electrical loads.

• Add up the rated watts (or amps) of all loads to be connected

at one time. This total should not be greater than (a) the rated

wattage/amperage capacity of the generator or (b) circuit

breaker rating of the receptacle supplying the power. See "Don't

Overload the Generator".

2.7 OVERLOAD PREVENTION

Overloading a generator in excess of its rated wattage capacity

can result in damage to the generator and to connected electrical

devices. Observe the following to prevent overloading the unit:

• Add up the total wattage of all electrical devices to be connected

at one time. This total should NOT be greater than the

generator's wattage capacity.

• The rated wattage of lights can be taken from light bulbs. The

rated wattage of tools, appliances and motors can usually be

found on a data label or decal affixed to the device.

• If the appliance, tool or motor does not give wattage, multiply

volts times ampere rating to determine watts (volts x amps =

watts).

• Some electric motors, such as induction types, require about

three times more watts of power for starting than for running.

This surge of power lasts only a few seconds when starting

such motors. Make sure to allow for high starting wattage when

selecting electrical devices to connect to the generator:

1. Figure the watts needed to start the largest motor.

2. Add to that figure the running watts of all other connected

loads.

The Wattage Reference Guide is provided to assist in determining

how many items the generator can operate at one time.

NOTE: All figures are approximate. See data label on appliance

for wattage requirements.

2.8 WATTAGE REFERENCE GUIDE

Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Running Watts

*Air Conditioner (12,000 Btu). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1700

*Air Conditioner (24,000 Btu). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3800

*Air Conditioner (40,000 Btu). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6000

Battery Charger (20 Amp). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

Belt Sander (3") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000

Chain Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Circular Saw (6-1/2") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .800 to 1000

*Clothes Dryer (Electric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5750

*Clothes Dryer (Gas) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

*Clothes Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1150

Coffee Maker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1750

*Compressor (1 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000

*Compressor (3/4 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1800

*Compressor (1/2 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1400

Curling Iron. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

*Dehumidifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650

Disc Sander (9"). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Edge Trimmer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

Electric Blanket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400

Electric Nail Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Electric Range (per element). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1500

Electric Skillet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1250

*Freezer . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..700

*Furnace Fan (3/5 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 875

*Garage Door Opener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .500 to 750

Hair Dryer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Hand Drill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .250 to 1100

Hedge Trimmer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450

Impact Wrench. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

13

Iron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

*Jet Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800

Lawn Mower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Light Bulb. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Microwave Oven. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .700 to 1000

*Milk Cooler. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1100

Oil Burner on Furnace. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300

Oil Fired Space Heater (140,000 Btu) . . . . . . . . . . . . . . . . . . . . . . . . 400

Oil Fired Space Heater (85,000 Btu) . . . . . . . . . . . . . . . . . . . . . . . . . 225

Oil Fired Space Heater (30,000 Btu) . . . . . . . . . . . . . . . . . . . . . . . . . 150

*Paint Sprayer, Airless (1/3 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 600

Paint Sprayer, Airless (handheld). . . . . . . . . . . . . . . . . . . . . . . . . . . . 150

Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 to 200

*Refrigerator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

Slow Cooker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200

*Submersible Pump (1-1/2 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2800

*Submersible Pump (1 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000

*Submersible Pump (1/2 HP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1500

*Sump Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .800 to 1050

*Table Saw (10") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1750 to 2000

Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 to 500

Toaster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1000 to 1650

Weed Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

* Allow 3 times the listed watts for starting these devices.

2.9 BEFORE STARTING THE GENERATOR

Prior to operating the generator, engine oil and gasoline will need

to be added, as follows:

2.9.1 ADDING ENGINE OIL

All oil should meet minimum American Petroleum Institute (API)

Service Class SJ, SL or better. Use no special additives. Select

the oil's viscosity grade according to the expected operating

temperature (also see chart).

• Above 40 °F

(4.4 °C), use SAE 30

• Below 40 °F

(4.4 °C) and down to 10 °F (-12 °C), use 10W-30

• Below 10 °F (-12 °C), use synthetic 5W-30

10W-30

SAE 30

Synthetic 5W-30



Any attempt to crank or start the engine before it has

been properly serviced with the recommended oil may

result in an engine failure.

3.6 - 8kW Portables

1. Place generator on a level surface (not to exceed 15° in any

direction).

2. Clean area around oil fill and remove oil fill cap.

3. Slowly fill engine with oil through the oil fill opening until it

reaches the full mark. Stop filling occasionally to check oil

level. The engine is full when the oil level reaches the bottom

threads of the mating oil fill cap.

4. Install the oil fill cap and finger tighten securely.

5. Check engine oil level before starting each time thereafter.

10kW Portables

1. Place generator on a level surface (not to exceed 15° in any

direction).

2. Clean area around oil fill and remove oil dipstick

3. Slowly fill engine with oil through the oil dipstick tube. Stop

filling occasionally to check oil level. The engine is full when

the oil reaches the full mark on the dipstick.

4. Install the oil dipstick.

5. Check engine oil level before starting each time thereafter.

2.9.2 ADDING GASOLINE

Use care when fueling the generator. Only fill the fuel tank when the

generator has cooled entirely. Use fresh unleaded gasoline with a

minimum Research Octane Number (RON) of 87.

NOTE: Do not use any gasoline containing more than 10%

Ethanol. NEVER fill the fuel tank with E85 or a mixture of oil and

gasoline designated for two-cycle engines.

(000105)

DANGER

Explosion and Fire. Fuel and vapors are extremely

ammable and explosive. Add fuel in a well

ventilated area. Keep re and spark away. Failure to

do so will result in death or serious injury.

Use regular UNLEADED gasoline with the generator engine. Do not

use premium gasoline. Do not mix oil with gasoline.

1. Clean area around fuel fill cap, remove cap.

2. Slowly add unleaded regular gasoline to fuel tank. Do not fill

above inner lip. Be careful not to overfill (Figure 16).

3. Install fuel cap and wipe up any spilled gasoline.

IMPORTANT: It is important to prevent gum deposits from forming

in fuel system parts such as the carburetor, fuel hose or tank

during storage. Alcohol-blended fuels (called gasohol, ethanol

or methanol) can attract moisture, which leads to separation and

formation of acids during storage. Acidic gas can damage the fuel

system of an engine while in storage. To avoid engine problems,

the fuel system should be emptied before storage of 30 days or

longer. See the "Storage" section. Never use engine or carburetor

cleaner products in the fuel tank as permanent damage may occur.

Operation

14

Figure 16 - Fuel Tank

DO NOT Fill Above Lip

Fuel

Fuel Tank

2.10 STARTING THE ENGINE (ELECTRIC START

ONLY)



Never start or stop engine with electrical devices

plugged into the receptacles AND devices turned on.

1. Unplug all electrical loads from the unit's receptacles before

starting the engine.

2. Make sure the unit is in a level position (not to exceed 15° in

any direction).

3. Locate the Idle Control ON/OFF switch on the control panel

and set it to the “OFF” position (Figure 17).

4. Open the fuel shut-off valve (Figure 18 (A)).

Figure 17 - Idle Control Switch

5. Pull the CHOKE knob outward to “Full Choke” position (Figure

18 (B)).

6. To start engine, press and hold the Start/Run/Stop switch in

the “Start” position. The engine will crank and attempt to start.

When the engine starts, release the switch to the run position.

7. When the engine starts, push choke knob in to “1/2 Choke”

position until the engine runs smoothly and then fully in to the

“Run” position. If engine falters, pull the choke knob back out

to “1/2 Choke” position until the engine runs smoothly and

then to “Run” position.

8. The 3.6 - 8kW portables are also equipped with a manual

recoil starter which may be used if the battery is discharged.

IMPORTANT: Do not overload the generator. Also, do not overload

individual panel receptacles. These outlets are protected against

overload with push-to-reset and 2-pole type circuit breakers. If

amperage rating of any circuit breaker is exceeded, that breaker

opens and electrical output to that receptacle is lost. Read “Don’t

Overload the Generator” carefully.

2.11 STARTING PULL START ENGINES



Never start or stop engine with electrical devices

plugged into the receptacles AND devices turned on.

1. Unplug all electrical loads from the unit's receptacles before

starting the engine.

2. Make sure the unit is in a level position (not to exceed 15° in

any direction).

3. OPEN the fuel shut-off valve (Figure 18 (A)).

4. Turn the OFF/ON/START switch to the "ON" position (6.5,

8Kw).

5. Pull the choke knob outward (Figure 18 (B)); or the ON/OFF

switch to the "ON" position (3.6kW).

Figure 18 - Fuel Shut-off Valve

000297

6. To start engine, firmly grasp the recoil handle and pull slowly

until increased resistance is felt. Pull rapidly up and away.

7. When engine starts, move the choke knob to the 1/2-CHOKE

position until engine runs smoothly and then fully to the RUN

position. If engine falters, move choke back out to 1/2-CHOKE

until engine runs smoothly and then to RUN.

NOTE: If engine fires, but does not continue to run, move choke

to FULL CHOKE and repeat starting instructions.

IMPORTANT: Do not overload the generator. Also, do not overload

individual panel receptacles. These outlets are protected against

overload with push-to-reset and 2-pole type circuit breakers. If

amperage rating of any circuit breaker is exceeded, that breaker

opens and electrical output to that receptacle is lost. Read “Don’t

Overload the Generator” carefully.

2.12 STOPPING THE ENGINE

1. Shut off all loads, then unplug the electrical loads from

generator panel receptacles. Never start or stop the engine

with electrical devices plugged in and turned on.

2. Let engine run at no-load for several minutes to stabilize the

internal temperatures of engine and generator.

3. Move START/RUN/STOP switch to the "OFF" position (6.5, 8

or 10kW); or the ON/OFF switch to the "OFF" position (3.6kW).

4. Close fuel valve.

Operation

B

A

15

2.13 LOW OIL LEVEL SHUTDOWN SYSTEM

The engine is equipped with a low oil level sensor that shuts down

the engine automatically when the oil level drops below a specified

level. If the engine shuts down by itself and the fuel tank has

enough gasoline, check engine oil level.

If the system senses a low oil level during operation, the engine

shuts down. The engine will not run until the oil has been refilled

to the proper level.

2.14 CHARGING THE BATTERY (IF EQUIPPED)



 Storage batteries give off explosive hydrogen gas while

recharging. An explosive mixture will remain around the

battery for a long time after it has been charged. The

slightest spark can ignite the hydrogen and cause an

explosion. Such an explosion can shatter the battery and

cause blindness or other serious injury.



Never permit smoking, open flame, sparks or any

other source of heat around a battery. Wear protective

goggles, rubber apron and rubber gloves when working

around a battery. Battery electrolyte fluid is an extremely

corrosive sulfuric acid solution that can cause severe

burns. If spill occurs flush area with clear water

immediately.

NOTE: The battery shipped with the generator has been fully

charged. A battery may lose some of its charge when not in

use for prolonged periods of time. If the battery is unable

to crank the engine, plug in the 12V charger included in the

accessory box (see section "Charging the Battery"). RUNNING

THE GENERATOR WILL CHARGE THE BATTERY.

Use battery charger plug to keep the battery charged and ready for

use. Battery charging should be done in a dry location.

1. Plug charger into “Battery Charger Input” jack, located on the

control panel. Plug wall receptacle end of the battery charger

into a 120 Volt AC wall outlet (Figure 19).

2. Unplug battery charger from wall outlet and control panel jack

when generator is going to be in use.

NOTE: Do not use the battery charger for more than 48 hours

at one charge. If the battery is completely discharged, start the

unit per the "Starting Pull Start Engines" section and recharge

the battery by running the unit.

Figure 19 - Battery Charger Jack

BATTERY

CHARGER

INPUT

3.1 PERFORMING SCHEDULED MAINTENANCE

It is important to perform service as specified in the Maintenance

Schedule for proper generator operation, and to ensure that the

generator complies with the applicable emission standards for the

duration of its useful life. Service and repairs may be performed by

any capable person or repair shop. Additionally, emissions critical

maintenance must be performed as scheduled in order for the

Emissions Warranty to be valid. Emissions critical maintenance

consists of servicing the air filter and spark plugs in accordance

with the Maintenance Schedule.

3.2 MAINTENANCE SCHEDULE

Follow the calendar intervals. More frequent service is required

when operating in adverse conditions noted below.

Check Oil Level At Each Use

Change Oil and Oil Filter‡ *Every 100 hours or Every Season

Check Valve Clearance ***Every Season

Service Air Filter ** Every 200 hours or Every Season

Replace Spark Plug Every 200 hours or Every Season

Clean Spark Arrestor Screen Every 100 hours or Every Season

‡ Change oil after first 30 hours of operation then every season.

* Change oil and oil filter every month when operating under heavy load or in high

temperatures.

** Clean more often under dirty or dusty operating conditions. Replace air filter

parts if they cannot be adequately cleaned.

*** Check valve clearance and adjust if necessary after first 50 hours of

operation and every 100 hours thereafter.

15

Maintenance

16

3.3 PRODUCT SPECIFICATIONS

3.3.1 GENERATOR SPECIFICATIONS

3.6kW

Rated Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6kW

Surge Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5kW

Rated AC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120/240

Rated Max AC Load

Current @ 240V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Amps**

Current @120V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Amps**

Rated Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Hz @3600 RPM

Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single Phase

6.5 kW

Rated Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5kW**

Surge Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.13kW**

Rated AC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120/240

Rated Max AC Load

Current @ 240V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27.1 Amps**

Current @120V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54.2 Amps**

Rated Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Hz @3600 RPM

Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single Phase

8.0 kW

Rated Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.0kW**

Surge Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10kW**

Rated AC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120/240

Rated Max AC Load

Current @ 240V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33.3 Amps**

Current @120V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66.7 Amps**

Rated Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Hz @3600 RPM

Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single Phase

10.0 kW

Rated Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10kW**

Surge Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12kW**

Rated AC Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120/240

Rated Max AC Load

Current @ 240V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41.7 Amps**

Current @120V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83.3 Amps**

Rated Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . .60 Hz @3600 RPM

Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single Phase

** Maximum wattage and current are subject to, and limited by, such factors

as fuel Btu content, ambient temperature, altitude, engine condition, etc..

Maximum power decreases about 3.5% for each 1,000 feet above sea level;

and will also decrease about 1% for each -12 °C (10° F) above 15.5 °C (60 °F)

ambient temperature.

3.3.2 ENGINE SPECIFICATIONS

3.6kW

Displacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .216.5cc

Spark Plug Type. . . . . . . . . . . . . . . . . . Champion RC14YC or Equivalent

Spark Plug Part Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0E7585

Spark Plug Gap . . . . . . . . . . . . . . . . . . . . . . . . . . .0.030 inch (0.76mm)

Gasoline Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 U.S. Gallons

Oil Type . . . . . . . . . . . . . . . . . . See Chart in “Adding Engine Oil” Section

Oil Capacity . . . . . . . . . . . . . . . . . . . w/Filter Change = 0.8 Qts (0.75 L)

w/out Filter Change = 0.5 Qts (0.47 L)

Oil Filter Part Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 070185B

Run Time (50% Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9.5 hours

Class I Emission Certified

6.5 & 8.0 kW

Displacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407cc

Spark Plug Type. . . . . . . . . . . . . . . . . . Champion RC14YC or Equivalent

Spark Plug Part Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0E7585

Spark Plug Gap . . . . . . . . . . . . . . . . . . . . . . . . . . .0.030 inch (0.76mm)

Gasoline Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 U.S. Gallons

Oil Type . . . . . . . . . . . . . . . . . . See Chart in “Adding Engine Oil” Section

Oil Capacity . . . . . . . . . . . . . . . . . . . . w/Filter Change = 1.5 Qts (1.4 L)

w/out Filter Change = 1.2 Qts (1.0 L)

Oil Filter Part Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 070185B

Run Time (50% Load . . . . . . . . . . . . .11 hours (6.5kW), 10 hours (8kW)

Class II Emission Certified

10.0 kW

Displacement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 530cc

Spark Plug Type. . . . . . . . . . . . . . . . . . . . . . NGK BPR6HS or Equivalent

Spark Plug Part Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0E9368

Spark Plug Gap . . . . . . . . . . . . . . . . . . . . . . . . . . .0.030 inch (0.76mm)

Gasoline Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . .9.25 U.S. Gallons

Oil Type . . . . . . . . . . . . . . . . . . See Chart in “Adding Engine Oil” Section

Oil Capacity . . . . . . . . . . . . . . . . . . . . w/Filter Change = 1.8 Qts (1.7 L)

w/out Filter Change = 1.5 Qts (1.4 L)

Oil Filter Part Number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 070185B

Run Time (50% Load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 hours

Class II Emission Certified

3.3.3 EMISSIONS INFORMATION

The Environmental Protection Agency (and California Air Resource

Board for generators certified to CA standards) require(s) that

this generator comply with exhaust and evaporative emission

standards. Locate the emissions compliance decal on the engine

to determine what standards the generator meets. This generator

is certified to operate on gasoline. The emission control system

consists of the following:

• Air Induction System

– Intake Pipe / Manifold

– Air Cleaner

• Fuel System

– Carburetor

– Fuel Tank / Cap

– Fuel Lines

– Evaporative Vent Lines

– Carbon Canister (for CA engines only)

• Ignition System

– Spark Plug

– Ignition Module

• Exhaust System

– Exhaust Manifold

– Muffler

– Catalyst (for CA engines only).

16

Maintenance

17

3.4 GENERAL RECOMMENDATIONS

The warranty of the generator does not cover items that have been

subjected to operator abuse or negligence. To receive full value

from the warranty, the operator must maintain the generator as

instructed in this manual.

Some adjustments will need to be made periodically to properly

maintain the generator.

All adjustments in the Maintenance section of this manual should

be made at least once each season. Follow the requirements in the

"Maintenance Schedule".

NOTE: Once a year replace the spark plug(s) and replace the

air filter. A new spark plug(s) and a clean air filter assure proper

fuel-air mixture, and help the engine run better and last longer.

3.4.1 GENERATOR MAINTENANCE

Generator maintenance consists of keeping the unit clean and dry.

Operate and store the unit in a clean dry environment where it will

not be exposed to excessive dust, dirt, moisture or any corrosive

vapors. Cooling air slots in the generator must not become clogged

with snow, leaves, or any other foreign material.

Check the cleanliness of the generator frequently and clean when

dust, dirt, oil, moisture or other foreign substances are visible on

its exterior surface.



Never insert any object or tool through the air cooling

slots, even if the engine is not running.

NOTE: DO NOT use a garden hose to clean generator. Water

can enter the engine fuel system and cause problems. In

addition, if water enters the generator through cooling air

slots, some water will be retained in voids and crevices of the

rotor and stator winding insulation. Water and dirt buildup on

the generator internal windings will eventually decrease the

insulation resistance of these windings.

3.4.2 TO CLEAN THE GENERATOR

• Use a damp cloth to wipe exterior surfaces clean.

• A soft, bristle brush may be used to loosen caked on dirt, oil,

etc.

• A vacuum cleaner may be used to pick up loose dirt and debris.

• Low pressure air (not to exceed 25 psi

(172 kPa)) may be

used to blow away dirt. Inspect cooling air slots and openings

on the generator. These openings must be kept clean and

unobstructed.

3.4.3 ENGINE MAINTENANCE

(000130)

WARNING

Accidental Start-up. Disconnect the negative battery

cable, then the positive battery cable when working

on unit. Failure to do so could result in death or serious

injury.

3.4.4 CHECKING OIL LEVEL

See the “Before Starting the Generator” section for information on

checking the oil level. The oil level should be checked before each

use, or at least every eight hours of operation. Keep the oil level

maintained.

3.4.5 CHANGING THE OIL AND OIL FILTER

Change the oil and oil filter after the first 30 hours of operation.

Change the oil every 100 hours or every season thereafter. If

running this unit under dirty or dusty conditions, or in extremely

hot weather, change the oil more often.



Hot oil may cause burns. Allow engine to cool before

draining oil. Avoid prolonged or repeated skin exposure

with used oil. Thoroughly wash exposed areas with soap.

Use the following instructions to change the oil after the engine

cools down:

1. Clean area around oil drain plug.

2. Remove oil drain plug from engine and oil fill plug (or dipstick)

to drain oil completely into a suitable container.

3. When oil has completely drained, install oil drain plug and

tighten securely.

4. Place a suitable container beneath the oil filter and turn filter

counterclockwise to remove. Discard according to local

regulations.

5. Coat gasket of new filter with clean engine oil. Turn filter

clockwise until gasket contacts lightly with filter adapter. Then

tighten an additional 3/4 turn.

6. Fill engine with recommended oil. (See “Before Starting the

Generator” for oil recommendations).

7. Wipe up any spilled oil.

8. Replace oil fill plug (or dipstick).

9. Dispose of used oil at a proper collection center.

3.4.6 REPLACING THE SPARK PLUG(S)

See Engine Specifications for recommended spark plug(s).

Replace the plug once each year. This will help the engine start

easier and run better.

1. Stop the engine and pull the spark plug wire(s) off of the spark

plug(s).

2. Clean the area around the spark plug(s) and remove it from the

cylinder head(s).

3. Set the spark plug's gap to 0.70-0.80 mm (0.028-0.031 in.).

Install the correctly gapped spark plug(s) into the cylinder

head(s) (Figure 20).

17

Maintenance

18

Figure 20 - Spark Plug Gap

000211

3.4.7 BATTERY REPLACEMENT (IF EQUIPPED)

The battery shipped with the generator has been provided fully

charged. Caution must be taken when connecting the battery.

NOTE: A battery may lose some of its charge when not in

use for prolonged periods of time. The battery may have to be

recharged before the first use. (See the "Know the Generator"

section.)

NOTE: For the 3.6kW - 8kW, order battery part number 0G9449.

For the 10kW, order battery part number 0H1663.

1. To replace the battery:

2. Slide the boots off of the battery terminals.

3. Disconnect the BLACK battery cable and the black battery

charger wire from the battery Negative terminal (–).

4. Disconnect the RED battery cable and the red battery charger

wire from the battery Positive terminal (+).

5. Remove the battery strap.

To install a new battery:

1. Reverse the steps above.

2. Double check all connections to ensure they are in the correct

location and secure. See Figure 3.

3. Secure battery with battery strap.

Battery Type: CP12-10, 12V, 10AH

3.4.8 AIR FILTER REPLACEMENT

The engine will not run properly and may be damaged if using

a dirty air cleaner. Clean or replace the air cleaner paper filter

once a year. Clean or replace more often if operating under dusty

conditions (Figures 21 through 23).

To clean or replace paper air filter:

1. Remove air cleaner cover and remove paper filter.

2. Clean paper filter by tapping it gently on a solid surface. If the

filter is too dirty, replace it with a new one. Dispose of the old

filter properly.

3. Clean air cleaner cover, then insert new paper filter into the

base of the air cleaner. Re-install air cleaner cover.

NOTE: To order a new air filter, please contact the nearest

authorized service center at 1-800-333-1322.

Figure 21 - 3.6kW Air Filter (Part Number 078601)

Base

Cover

Filter

Figure 22 - 6.5 & 8kW Air Filter (Part Number 073111)

BASE

FILTER

COVER

Figure 23 - 10kW Air Filter (Part Number 073111)

Maintenance

La page est en cours de chargement...

Generac XP6500E 0059340 Manuel utilisateur

Generac XP6500E 0059340 Manuel utilisateur

dans d''autres langues