Bose LIFESTYLE V35 Setup Manual

Taper
Setup Manual

Ce manuel convient également à

©2010 Bose Corporation, The Mountain,
F
ramingham, MA 01701-9168 USA
AM324443 Rev.00
LIFESTYLE
®
V35/V25 HOME ENTERTAINMENT SYSTEMS
LIFESTYLE
®
T20/ T10 HOME THEATER SYSTEMS
Setup Guide | Guía de instalación | Guide d'installation
Cover_8.5x6.5_Setup Guide_3L.fm Page 1 Monday, November 9, 2009 2:47 PM
ii
EnglishTAB 6TAB 8 TAB 7 TAB 3TAB 5 TAB 2TAB 4
SAFETY INFORMATION
Please read this guide
Please take the time to follow the instructions in this guide
carefully. They will help you set up and use your system properly
so you can enjoy its advanced features. Please save this guide for
future reference.
The lightning flash with arrowhead symbol within an
equilateral triangle alerts the user to the presence of
uninsulated, dangerous voltage within the system enclosure
that may be of sufficient magnitude to constitute a risk of
electric shock.
The exclamation point within an equilateral triangle alerts
the user to the presence of important operating and
maintenance instructions in this guide.
WARNINGS:
To reduce the risk of fire or electrical shock, do not expose the
product to rain or moisture.
Do not expose this apparatus to dripping or splashing, and do not
place objects filled with liquids, such as vases, on or near the
apparatus. As with any electronic products, use care not to spill
liquids into any part of the system. Liquids can cause a failure
and/or a fire hazard.
Do not place any naked flame sources, such as lighted candles,
on or near the apparatus.
Keep the remote control battery away from children. It may cause a
fire or chemical burn if mishandled. Do not recharge, disassemble,
heat above 100ºC (212ºF), or incinerate. Dispose of used batteries
promptly. Replace only with a battery of the correct type and model
number.
Contains small parts that may be a choking hazard.
Not suitable for children under age 3.
CAUTIONS:
Make no modifications to the system or accessories. Unauthorized
alterations may compromise safety, regulatory compliance, and
system performance, and may void the warranty.
Long-term exposure to loud music may cause hearing damage.
It is best to avoid extreme volume when using headphones,
especially for extended periods.
Notes:
Where the mains plug or appliance coupler is used as the discon-
nect device, such disconnect device shall remain readily operable.
The product must be used indoors. It is neither designed nor tested
for use outdoors, in recreation vehicles, or on boats.
This product is intended to be used only with the power supply
provided.
The product label is located on the bottom of the product.
Additional safety information
See the additional instructions on the Important Safety Information
sheet enclosed in the shipping carton.
Batteries
Please dispose of used batteries properly, following any
local regulations. Do not incinerate.
Class B emissions
This device complies with FCC and Industry Canada RF radiation
exposure limits set forth for general population. It must not be
co-located or be operating in conjunction with any other antennas
or transmitters.
Th
is product conforms to all EU Directive requirements as
applicable by law. The complete Declaration of Conformity
can be found at www.Bose.com/compliance.
©2010 Bose Corporation. No part of this work may be reproduced,
modified, distributed, or otherwise used without prior written permission.
ResoluteVigilantSetup.book Page ii Monday, December 7, 2009 11:59 AM
1
TAB 5TAB 4TAB 6TAB 8TAB 7English TAB 3TAB 2 TAB 5TAB 4TAB 6TAB 8TAB 7English TAB 3TAB 2
SYSTEM SETUP
Welcome
Thank you for choosing a Bose
®
LIFESTYLE
®
system
for your home. This guide provides step-by-step
instructions for setting up your new system. There
are two phases to the setup process:
Physical setup phase: Placing the system
components and connecting them together.
Interactive setup phase: Completing your setup
following the interactive steps on your TV screen
provided by the Unify
TM
intelligent integration system.
Unpacking
The parts of your new system are packaged in four
numbered kits plus a small box containing the
appropriate power cords:
Control console kit
Acoustimass
®
module kit
• Speaker kit
Interactive kit
Power cord kit (used with kits 1 and 2)
Starting with Kit 1, unpack each kit and set up its
contents before unpacking the next one.
Be sure to save all of the packing materials. These
provide the safest means for any necessary shipping
or transporting.
If any part appears damaged, do not attempt to use
it. Notify Bose or your authorized Bose dealer
immediately. For Bose contact information, refer
to the address sheet included in Kit 4.
1
1
2
3
4
ResoluteVigilantSetup.book Page 1 Monday, December 7, 2009 11:59 AM
2
SYSTEM SETUP
EnglishTAB 6TAB 8 TAB 7 TAB 3TAB 5 TAB 2TAB 4
Control console kit
What you need for the following steps:
1. Place the control console on a flat, stable surface
near your TV.
Note: Until your system is completely installed, it may be
helpful to keep the control console positioned for easy
access to its rear connection panel.
1
1
Control console
Power cord
Power supply
HDMI cable
Audio input cable
From the
power
cord kit
From Kit 1
Control
console
ResoluteVigilantSetup.book Page 2 Monday, December 7, 2009 11:59 AM
3
SYSTEM SETUP
TAB 5TAB 4TAB 6TAB 8TAB 7English TAB 3TAB 2
2. Plug one end of the HDMI cable into an HDMI
INPUT connector on your TV.
If an HDMI cable is already connected to an
HDMI input on your TV, you can use this one.
Just disconnect the other end.
3. Plug the other end of the HDMI cable you are using
into the connector labeled HDMI OUT Video to
TV on the control console.
HDMI OUT
Video to TV
ResoluteVigilantSetup.book Page 3 Monday, December 7, 2009 11:59 AM
4
SYSTEM SETUP
EnglishTAB 6TAB 8 TAB 7 TAB 3TAB 5 TAB 2TAB 4
4. Plug one end of the audio input cable into the
Acoustimass
®
Module connector on the control
console.
Make sure the flat surface with the arrow on the
plug faces up.
Leave the other end of the cable on the floor.
You will be asked to connect it while setting up
the next kit.
5. Plug the power supply output cord into the control
console Power connector.
6. Remove a power cord
from the power cord kit.
7. Plug one end of the power cord into the power
supply. Make sure you push the plug in as far as
it can go.
8. Plug the other end of the power cord into a live
AC (mains) power outlet.
9. Continue with Kit on the next page.
Acoustimass
Module
Power supply
output cord
AC
power
cord
Power
Power
supply
2
ResoluteVigilantSetup.book Page 4 Monday, December 7, 2009 11:59 AM
5
SYSTEM SETUP
TAB 5TAB 4TAB 6TAB 8TAB 7English TAB 3TAB 2
Acoustimass
®
module kit
What you need for the following steps:
1. Place the Acoustimass module on the floor at the
same end of the room as the TV. Make sure there is
a live AC outlet nearby.
2. Lay the module on its side and locate the
connector panel.
2
Acoustimass module
Power cord
From the
power
cord kit
From Kit 2
Acoustimass
module
Connector
panel
ResoluteVigilantSetup.book Page 5 Monday, December 7, 2009 11:59 AM
6
SYSTEM SETUP
EnglishTAB 6TAB 8 TAB 7 TAB 3TAB 5 TAB 2TAB 4
CAUTION: DO NOT
stand the Acoustimass
®
module on its front or
back end.
3. Plug the free end of the audio input cable into the
Media Center connector on the Acoustimass
module.
Make sure the flat surface with the arrow faces the
front of the module.
4. Remove a power cord
from the power cord kit.
5. Plug one end of the power cord into the AC Power
connector on the Acoustimass module. Make sure
you push the plug in as far as it can go.
6. Plug the other end of the power cord into a live
AC (mains) power outlet.
7. Continue with Kit on the next page.
Media Center
AC Power
3
ResoluteVigilantSetup.book Page 6 Monday, December 7, 2009 11:59 AM
7
SYSTEM SETUP
TAB 5TAB 4TAB 6TAB 8TAB 7English TAB 3TAB 2
Speaker kit
What you need for the following steps:
From Kit 3: System speakers
(one set of the three types shown)
Note: You can place system speakers on wall brackets or
floor stands. To purchase these accessories, contact your
local Bose dealer or visit www.Bose.com.
3
Jewel Cube
®
speakers
(5) Left or right, front or rear, and center front speaker
(1) Center front speaker
Direct/Reflecting
®
cube speaker arrays
Virtually Invisible
®
single cube speakers
(4) Left or right, front
or rear speaker
(1) Center front speaker(4) Left or right, front
or rear speaker
Left front (L)
White
Center front (C)
Brown
Rear speaker cables
Left rear (LR)
Light green
Right rear (RR)
Purple
Front speaker cables
Right front (R)
Light blue
ResoluteVigilantSetup.book Page 7 Monday, December 7, 2009 11:59 AM
8
SYSTEM SETUP
EnglishTAB 6TAB 8 TAB 7 TAB 3TAB 5 TAB 2TAB 4
1. Place the center front speaker on a stable and level
surface directly above or below the center of your
TV screen as in the following example.
2. Place one speaker to the left and one to the right of
the TV.
Keep each speaker within 3 ft (1 m) of the TV
screen to prevent too much separation of the
sound from the picture. Vary this distance to suit
your room conditions and personal preference.
If placing the speakers in an enclosed bookcase
shelf, position them at the front edge of the shelf.
If you have Jewel Cube
®
or Direct/Reflecting
®
cube speakers, rotate the cubes so that one
cube of each speaker points forward into the
room and the other points at a side wall to
create reflected sound.
ResoluteVigilantSetup.book Page 8 Monday, December 7, 2009 11:59 AM
9
SYSTEM SETUP
TAB 5TAB 4TAB 6TAB 8TAB 7English TAB 3TAB 2
3. Place the rear speakers toward the back of the
room behind the viewers at ear height (when
seated) or higher, if possible.
Make sure the 50 ft (15.2 m) rear speaker cables
will reach from the speakers to the Acoustimass
®
module.
Aim the speakers away from the listeners to pre-
vent them from pinpointing the exact location of the
sound source.
If you have Jewel Cube
®
or Direct/Reflecting
®
cube speakers, rotate the cubes so that one
cube of each speaker points forward into the
room and the other points at a side wall to
create reflected sound.
4. Locate the colored connectors on the bottom panel
of the Acoustimass module.
5. Plug the speaker cables into the Acoustimass
module connectors. Be sure to match each cable
plug to each connector by the color code.
Left rear
(LR)
Right rear
(RR)
Colored connectors
ResoluteVigilantSetup.book Page 9 Monday, December 7, 2009 11:59 AM
10
SYSTEM SETUP
EnglishTAB 6TAB 8 TAB 7 TAB 3TAB 5 TAB 2TAB 4
6. Locate the speaker position markings on the free
ends of the speaker cables.
7. Using the speaker position markings, run each
cable out to its respective speaker as in the
following setup example of a room.
Speaker position marking
(L, C, R, LR, or RR)
FRONT
SPEAKERS
REAR
SPEAKERS
ResoluteVigilantSetup.book Page 10 Monday, December 7, 2009 11:59 AM
11
SYSTEM SETUP
TAB 5TAB 4TAB 6TAB 8TAB 7English TAB 3TAB 2
8. Connect the speaker cable to the type of speaker
you have.
9. Put the Acoustimass
®
module in its final position:
Upright (BEST) or on either side (ALTERNATE).
With the front opening facing into the room.
At least 18 in (45 cm) from any TV to avoid
magnetic interference with the TV image. Move
it farther away if you still notice interference.
CAUTION: Do not put electronic media, such as video or
audio tapes, on or next to the module for long periods of
time. The magnetic field surrounding the module may
erase some or all of the recorded material.
CAUTION: DO NOT BLOCK the
ventilation openings on the module.
This can cause it to overheat.
10. Continue with Kit on the next page.
For Jewel Cube
®
speakers:
Insert the plug into the speaker
connector.
For Direct/Reflecting
®
and
Virtually Invisible
®
single
cube speakers:
Press the button and insert the
wires. Connect the red-collared
wire to the red connector.
Connect the other wire to the
black connector.
Note: The rear speaker cables
for Direct/Reflecting
®
and
Virtually Invisible
®
cube speakers
are webbed together. You can
pull them apart as needed.
ALTERNATE
BEST
4
ResoluteVigilantSetup.book Page 11 Monday, December 7, 2009 11:59 AM
12
SYSTEM SETUP
EnglishTAB 6TAB 8 TAB 7 TAB 3TAB 5 TAB 2TAB 4
Interactive kit
What you need for the following steps:
Congratulations! At this point you have set up the
control console, the Acoustimass
®
module, and the
speakers. You are now ready to turn on your system
and enter the interactive phase of the setup process
using the Unify
TM
intelligent integration system.
IMPORTANT!
Before you start, make sure your speakers and
Acoustimass module are in their final
positions.
Do not connect any devices to the control
console at this time. The instructions provided
on your TV will tell you when to do this.
1. Slide the battery compartment cover off the back
of the remote control.
2. Install four AA (IEC LR6) batteries, matching the
polarity markings (+ and –) to the markings inside
the battery compartment.
3. Slide the battery cover back into place.
4
Remote control
with batteries
ADAPTiQ
®
audio
calibration
headset
From Kit 4
AA (IEC LR6) batteries (4)
Battery compartment cover
ResoluteVigilantSetup.book Page 12 Monday, December 7, 2009 11:59 AM
13
SYSTEM SETUP
TAB 5TAB 4TAB 6TAB 8TAB 7English TAB 3TAB 2
4. Press the power button ( ) on the control console
to turn on your system.
Because the system is in a low power state when
in standby, it takes several seconds to start. When
the power light changes from blinking to steady
green, your system is ready to use.
5. Turn on your TV.
6. Using the remote that came with your TV, change
the TV input to the one that is connected to your
LIFESTYLE
®
system.
7. Follow the instructions on your TV screen. You will
be prompted to do the following:
Select your language.
Optimize the audio from your system using the
ADAPTiQ
®
audio calibration system.
Connect audio/video devices to the
control console.
Configure your Bose
®
remote to control your
connected devices.
Other Kit 4 items
The remaining items in Kit 4 may or may not be
required to set up your LIFESTYLE
®
system. For more
information on using these accessories or adding other
devices to your system at another time, see the
operating guide.
Power
light
L
IFESTYLE
®
V35/V25
H
OME
E
NTERTAINMENT
S
YSTEMS
L
IFESTYLE
®
T20/ T10
H
OME
T
HEATER
S
YSTEMS
Operating Guide | Guía del usuario | Guide d’utilisation
L
IFESTYLE
®
V35/V25
H
OME
E
NTERTAINMENT
S
YSTEMS
L
IFESTYLE
®
T20/ T10
H
OME
T
HEATER
S
YSTEMS
Operating Guide | Guía del usuario | Guide d’utilisation
L
IFESTYLE
®
V35/V25
H
OME
E
NTERTAINMENT
S
YSTEMS
L
IFESTYLE
®
T20/ T10
H
OME
T
HEATER
S
YSTEMS
Operating Guide | Guía del usuario | Guide d’utilisation
L
IFESTYLE
®
V35/V25
H
OME
E
NTERTAINMENT
S
YSTEMS
L
IFESTYLE
®
T20/ T10
H
OME
T
HEATER
S
YSTEMS
Operating Guide | Guía del usuario | Guide d’utilisation
L
IFESTYLE
®
V35/V25
H
OME
E
NTERTAINMENT
S
YSTEMS
L
IFESTYLE
®
T20/ T10
H
OME
T
HEATER
S
YSTEMS
Operating Guide | Guía del usuario | Guide d’utilisation
L
IFESTYLE
®
V35/V25
H
OME
E
NTERTAINMENT
S
YSTEMS
L
IFESTYLE
®
T20/ T10
H
OME
T
HEATER
S
YSTEMS
Operating Guide | Guía del usuario | Guide d’utilisation
L
IFESTYLE
®
V35/V25
H
OME
E
NTERTAINMENT
S
YSTEMS
L
IFESTYLE
®
T20/ T10
H
OME
T
HEATER
S
YSTEMS
Operating Guide | Guía del usuario | Guide d’utilisation
L
IFESTYLE
®
V35/V25
H
OME
E
NTERTAINMENT
S
YSTEMS
L
IFESTYLE
®
T20/ T10
H
OME
T
HEATER
S
YSTEMS
Operating Guide | Guía del usuario | Guide d’utilisation
L
IFESTYLE
®
V35/V25
H
OME
E
NTERTAINMENT
S
YSTEMS
L
IFESTYLE
®
T20/ T10
H
OME
T
HEATER
S
YSTEMS
Operating Guide | Guía del usuario | Guide d’utilisation
Stereo audio cable
IR emitter cable
AM antenna*
FM antenna*
iPod/iPhone-
compatible
dock*
USB flash drive
(for system
updating only)
Operating guide
Rubber feet
for Acoustimass
®
module
Rubber feet
for front center
speaker
*For LIFESTYLE
®
V25 and V35 systems only.
ResoluteVigilantSetup.book Page 13 Monday, December 7, 2009 11:59 AM
14
SYSTEM SETUP
EnglishTAB 6TAB 8 TAB 7 TAB 3TAB 5 TAB 2TAB 4
Applying rubber feet
When placing the Acoustimass
®
module on bare floors,
you can attach the included rubber feet to the bottom
of the module for greater stability and to protect your
floor.
Vibration can cause speakers to move, particularly if
placed on a smooth surface like glass or highly
polished wood. If you are placing the center speaker on
such a surface, you can attach the included rubber feet
to the bottom of the speaker for greater stability.
If you have setup problems
If you experience any difficulties during the setup
process, such as an unrecognized device remote or
a connection error, you can reactivate the interactive
setup mode at any time and correct or change part of
your system setup. See “Using the Setup Mode” in
your system operating guide.
For help in trying to resolve any problems, see the
troubleshooting table in your system operating guide.
Contacting customer service
For additional help in solving problems, contact Bose
®
Customer Service. See the address sheet included in
Kit 4.
Bottom panel
Rubber feet
for
Acoustimass
module
Rubber feet
for
front center
speaker
Bottom panel
of center
speaker
Applicable only for LIFESTYLE
®
V25 and V35
home entertainment systems
“Made for iPod” means that an electronic
accessory has been designed to connect
specifically to iPod and has been certified by
the developer to meet Apple performance
standards.
Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards.
iPod and iPhone are trademarks of Apple, Inc., registered in
the U.S. and other countries. All other marks are registered
trademarks and trademarks of Bose Corporation.
ResoluteVigilantSetup.book Page 14 Monday, December 7, 2009 11:59 AM
©2010 Bose Corporation, The Mountain,
F
ramingham, MA 01701-9168 USA
AM324443 Rev.00
LIFESTYLE
®
V35/V25 HOME ENTERTAINMENT SYSTEMS
LIFESTYLE
®
T20/ T10 HOME THEATER SYSTEMS
Setup Guide | Guía de instalación | Guide d'installation
L
IFESTYLE
®
235/135
HOME ENTERTAINMENT
SYSTEMS
L
IFESTYLE
®
V35/V25
HOME ENTERTAINMENT
SYSTEMS
L
IFESTYLE
®
T20/T10
HOME THEATER
SYSTEMS
Operating Guide | Guía del usuario | Guide d’utilisation
2012 Bose Corporation, The Mountain,
Framingham, MA 01701-9168 USA
AM348139 Rev 00
LIFESTYLE
®
235/135/V35/V25 HOME ENTERTAINMENT SYSTEMS AND LIFESTYLE
®
T20/T10 HOME THEATER SYSTEMS
Operating Cover Defender_5.5x8.5_AIM_3L.fm Page 1 Thursday, December 1, 2011 4:44 PM
ii – English
SAFETY INFORMATION
Please read this guide
Please take the time to follow the instructions in this guide carefully. They will help you set up and
use your system properly so you can enjoy its advanced features. Please save this guide for future
reference.
All Bose products must be used in accordance with local, state, federal, and industry regulations.
The lightning flash with arrowhead symbol within an equilateral triangle alerts the user to the
presence of uninsulated, dangerous voltage within the system enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle alerts the user to the presence of
important operating and maintenance instructions in this guide.
WARNINGS:
To reduce the risk of fire or electrical shock, do not expose the product to rain or moisture.
Do not expose this apparatus to dripping or splashing, and do not place objects filled with liquids,
such as vases, on or near the apparatus. As with any electronic products, use care not to spill liquids
into any part of the system. Liquids can cause a failure and/or a fire hazard.
Do not place any naked flame sources, such as lighted candles, on or near the apparatus.
Contains small parts that may be a choking hazard. Not suitable for children under
age 3.
CAUTIONS:
Make no modifications to the system or accessories. Unauthorized alterations may
compromise safety, regulatory compliance, and system performance, and may void the warranty.
Long-term exposure to loud music may cause hearing damage. It is best to avoid extreme volume
when using headphones, especially for extended periods.
Notes:
Where the mains plug or appliance coupler is used as the disconnect device, such disconnect device
shall remain readily operable.
The product must be used indoors. It is neither designed nor tested for use outdoors, in recreation
vehicles, or on boats.
This product is intended to be used only with the power supply provided.
The product label is located on the bottom or the back of the product.
The interconnect cables included with this system are not approved for in-wall installation. Please
check your local building codes for the correct type of wire and cable required for in-wall installation.
Please dispose of used batteries properly, following any local regulations.
Do not incinerate.
Additional safety information
See the additional instructions on the Important Safety Information sheet enclosed in the shipping
carton.
Bose Corporation hereby declares that this product is in compliance with the essential
requirements and other relevant provisions of the Directive 1999/5/EC and other applicable
Directives. The complete Declaration of the Conformity can be found at:
www.Bose.com/compliance
Th
is product conforms to all EU Directive requirements as applicable by law. The complete
Declaration of Conformity can be found at www.Bose.com/compliance.
Defender OpG.book Page ii Thursday, November 10, 2011 11:44 AM
English – iii
Note
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, you are encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a different circuit than the one to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by Bose Corporation could void the users
authority to operate this equipment.
These devices comply with FCC and Industry Canada RF radiation exposure limits set forth for the
general population. They must not be co-located or be operating in conjunction with any other
antennas or transmitters.
These devices comply with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) This device may not cause interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation of the
device.
The 135 Speaker array has an output power of 6 mW @ 2406-2474 MHz.
The 135 Acoustimass Module has an output power of 2 mW @ 2406-2474 MHz.
Designed with UEI
®
Technology™ Under License from Universal Electronics Inc. ©UEI 2000-2011.
HDMI
TM
and the HDMI logo are trademarks or registered trademarks of HDMI Licensing, LLC in the
United States and other countries.
iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks of Apple, Inc., registered in
the U.S. and other countries.
Xbox is a trademark of Microsoft Corporation.
TiVo is a trademark of TiVo, Inc. or its subsidiaries.
Other trademarks are property of their respective owners.
Manufactured under license from Dolby Laboratories. Dolby and the double-D
symbol are registered trademarks of Dolby Laboratories.
Names and Contents of Toxic or Hazardous Substances or Elements
Part Name
Toxic or Hazardous Substances and Elements
Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent (CR(VI)) Polybrominated Biphenyl (PBB) Polybrominated diphenylether (PBDE)
PCBs
X0 0 0 0 0
Metal parts
X0 0 0 0 0
Plastic parts
00 0 0 0 0
Speakers
X0 0 0 0 0
Cables
X0 0 0 0 0
0
: Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in SJ/T 11363-2006.
X
: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T 11363-2006.
SAFETY INFORMATION
Defender OpG.book Page iii Thursday, November 10, 2011 11:44 AM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63

Bose LIFESTYLE V35 Setup Manual

Taper
Setup Manual
Ce manuel convient également à

dans d''autres langues