ASROCK K7VT4A PRO Le manuel du propriétaire

11

1

ASRock K7VT4A Pro Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any

kind, either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

ASRock Website: http://www.asrock.com

Published December 2004

22

2

ASRock K7VT4A Pro Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

1 PS2_USB_PWR1 Jumper 15 Chassis Fan Connector (CHA_FAN1)

2 CPU Fan Connector (CPU_FAN1) 16 System Panel Connector (PANEL1)

3 CPU Socket 17 Chassis Speaker Connector (SPEAKER 1)

4 North Bridge Controller 18 USB 2.0 Connector (USB67, Blue)

5 184-pin DDR DIMM Slots (DDR1- 2) 19 Floppy Connector (FLOPPY1)

6 ATX Power Connector (ATXPWR1) 20 Internal Audio Connector: CD1 (Black)

7 Secondary IDE Connector (IDE2, Black) 21 Internal Audio Connector: AUX1 (White)

8 Primary IDE Connector (IDE1, Blue) 22 Clear CMOS Jumper (CLRCMOS2)

9 AGP Slot (1.5V_AGP1) 23 JR1 / JL1 Jumpers

10 FSB Select Jumpers 24 Front Panel Audio Connector (AUDIO1)

(FSB_SEL0, FSB_SEL1, FSB_SEL2) 25 PCI Slots (PCI1- 5)

11 South Bridge Controller 26 Game Port Connector (GAME1)

12 Primary Serial ATA Connector (SATA1) 27 Flash Memory

13 Secondary Serial ATA Connector (SATA2) 28 Shared USB 2.0 Header (JUSB45, Blue)

14 Power LED Connector (PWR_LED1) 29 J1 Jumper (FID0, FID1, FID2, FID3, FID4)

33

3

ASRock K7VT4A Pro Motherboard

EnglishEnglish

English

ASRock I/O PlusASRock I/O Plus

ASRock I/O Plus

TMTM

TM

1 Parallel Port 7 2 x USB 2.0 Port (USB0, USB1)

2 RJ-45 Port 8 2 x USB 2.0 Port (USB2, USB3)

3 Line In (Light Blue) 9 Serial Port: COM1

4 Line Out (Lime) 10 PS/2 Keyboard Port (Purple)

5 Microphone (Pink) 11 PS/2 Mouse Port (Green)

6 2 x Shared USB 2.0 Port (USB4, USB5)

44

4

ASRock K7VT4A Pro Motherboard

1.1.

1.

IntroductionIntroduction

Introduction

Thank you for purchasing ASRock K7VT4A Pro motherboard, a reliable motherboard

produced under ASRock’s consistently stringent quality control. It delivers excellent

performance with robust design conforming to ASRock’s commitment to quality and

endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might

be updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest memory and CPU support lists on ASRock website

as well.

ASRock website http://www.asrock.com

1.11.1

1.1

Package ContentsPackage Contents

Package Contents

1 x ASRock K7VT4A Pro Motherboard

(ATX Form Factor: 12.0-in x 7.0-in, 30.5 cm x 17.8 cm)

1 x ASRock K7VT4A Pro Quick Installation Guide

1 x ASRock K7VT4A Pro Support CD

1 x Ultra ATA 66/100/133 IDE Ribbon Cable (80-conductor)

1 x 3.5-in Floppy Drive Ribbon Cable

1 x Serial ATA (SATA) Data Cable

1 x Serial ATA (SATA) HDD Power Cable (Optional)

1 x ASRock I/O Plus

TM

Shield

EnglishEnglish

English

55

5

ASRock K7VT4A Pro Motherboard

EnglishEnglish

English

1.21.2

1.2

SpecificationsSpecifications

Specifications

Platform: ATX Form Factor: 12.0-in x 7.0-in, 30.5 cm x 17.8 cm

CPU: Supports Socket A (462 pins) for

AMD Athlon

TM

/ Athlon

TM

XP / Duron

TM

/ Sempron

TM

processor

Chipsets: North Bridge:

VIA KT400A, FSB@200 / 266 / 333 MHz

South Bridge:

VIA VT8237, Supports USB 2.0, ATA 133, SATA 1.5Gb/s

Memory: 2 DDR DIMM slots: DDR1and DDR2

PC2100 (DDR266) / PC2700 (DDR333)

for 2 DDR DIMM slots, Max. 2GB;

PC3200 (DDR400) for 1 DDR DIMM slot, Max. 1GB

IDE: IDE1: ATA 133 / Ultra DMA Mode 6

IDE2: ATA 133 / Ultra DMA Mode 6

Supports up to 4 IDE Devices

Serial ATA: 2 SATA Connectors, Support 1.5Gb/s Data Transfer Rate

Floppy Port: Supports up to 2 Floppy Disk Drives

Audio: 5.1 Channels AC’97 Audio

LAN: Speed: 802.3u (10/100 Ethernet), Supports Wake-On-LAN

Hardware Monitor: CPU Temperature Sensing

Motherboard Temperature Sensing

CPU Overheat Shutdown to Protect CPU Life

(ASRock U-COP)(see CAUTION 1)

CPU Fan Tachometer

Chassis Fan Tachometer

Voltage Monitoring: +12V, +5V, +3.3V, Vcore

PCI slots: 5 Slots with PCI Specification 2.2

AGP slot: 1 AGP Slot, Supports 1.5V, 8X/4X AGP Card (see CAUTION 2)

USB 2.0: 8 USB 2.0 ports:

include 6 ready-to-use USB 2.0 ports on the rear panel,

plus one on-board header supporting 2 extra USB 2.0 ports

(see CAUTION 3)

ASRock I/O Plus

TM

: 1 PS/2 Mouse Port, 1 PS/2 Keyboard Port,

1 Serial Port: COM1,

1 Parallel Port (ECP/EPP Support)

6 ready-to-use USB 2.0 Ports,

1 RJ-45 Port,

Audio Jack: Line In / Line Out / Microphone

66

6

ASRock K7VT4A Pro Motherboard

BIOS: AMI legal BIOS, Supports “Plug and Play”,

ACPI 1.1 Compliance Wake-Up Events,

SMBIOS 2.3.1 Support,

CPU Frequency Stepless Control

(only for advanced users’ reference, see CAUTION 4)

OS: Microsoft

®

Windows

®

98 SE / ME / 2000 / XP Compliant

CAUTION!

1. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the

motherboard functions properly and unplug the power cord, then plug it

back again. To improve heat dissipation, remember to spray thermal

grease between the CPU and the heatsink when you install the PC system.

2. Do NOT use a 3.3V AGP card on the AGP slot of this motherboard!

It may cause permanent damage!

3. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

XP SP1/2000 SP4. It may not work properly under Microsoft

®

Windows

®

98/ME. Please refer to Microsoft

®

official document at

http://www.microsoft.com/whdc/hwdev/bus/USB/USB2support.mspx

4. Although this motherboard offers stepless control, it is not recommended

to perform over clocking. Frequencies other than the recommended CPU

bus frequencies may cause the instability of the system or damage the

CPU. The CPU host frequency of this motherboard is determined by

jumper-setting. You must adjust “FSB Select Jumpers” according to the

FSB of your AMD CPU before you set the “CPU Host Frequency” con-

figuration as “Manual” in BIOS. See page 9 for the details of “FSB Select

Jumpers” adjustment, and page 25 of “User Manual” in the Support CD for

“CPU Host Frequency” configuration.

EnglishEnglish

English

77

7

ASRock K7VT4A Pro Motherboard

2.2.

2.

InstallationInstallation

Installation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install mother-

board components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the car-

pet or the like. Also remember to use a grounded wrist strap or

touch a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a

grounded antstatic pad or in the bag that comes with the

component.

5. When placing screws into the screw holes to secure the

motherboard to the chassis, please do not over-tighten the screws!

Doing so may damage the motherboard.

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90° angle.

Step 2. Position the CPU directly above the socket such that its marked corner

matches the base of the socket lever.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab

to indicate that it is locked.

Step 5. Install CPU fan and heatsink. For proper installation, please kindly refer to

the instruction manuals of your CPU fan and heatsink vendors.

EnglishEnglish

English

88

8

ASRock K7VT4A Pro Motherboard

2.22.2

2.2

Installation of Memory Modules (DIMM)Installation of Memory Modules (DIMM)

Installation of Memory Modules (DIMM)

K7VT4A Pro motherboard provides two 184-pin DDR (Double Data Rate) DIMM slots.

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break

on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into the

slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully

snap back in place and the DIMM is properly seated.

EnglishEnglish

English

99

9

ASRock K7VT4A Pro Motherboard

2.3 Expansion Slots (PCI and AGP Slots)2.3 Expansion Slots (PCI and AGP Slots)

2.3 Expansion Slots (PCI and AGP Slots)

There are 5 PCI slots and 1 AGP slot on K7VT4A Pro motherboard.

PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

AGP slot: The AGP slot is used to install a graphics card. The ASRock AGP slot has

a special design of clasp that can securely fasten the inserted graphics

card.

Please do NOT use a 3.3V AGP card on the AGP slot of this motherboard!

It may cause permanent damage! For the voltage information of your

graphics card, please check with the graphics card vendors.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the bracket facing the slot that you intend to use. Keep the screw

for later use.

Step 3. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 4. Fasten the card to the chassis with screws.

2.4 Jumpers Setup2.4 Jumpers Setup

2.4 Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on the pins, the jumper is “Open”.

The illustration shows a 3-pin jumper whose

pin1 and pin2 are “Short” when jumper cap

is placed on these 2 pins.

Jumper Setting

FSB Select Jumpers

(FSB_SEL0,

FSB_SEL1,

FSB_SEL2)

(see p.2 item 10)

Note: The CPU FSB frequency of this motherboard is determined by jumper-setting. You must

adjust “FSB Select Jumpers” according to the FSB of your AMD CPU. Please follow the

figures above to set the CPU FSB frequency.

Short Open

EnglishEnglish

English

1010

10

ASRock K7VT4A Pro Motherboard

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.2 item 1) +5VSB (standby) for PS/2 or

USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by power

supply.

JR1 / JL1 Jumpers

(see p.2 item 23)

Note: If JR1 and JL1 Jumpers are short, both the front panel and the rear panel audio

connectors can work.

Clear CMOS Jumper

(CLRCMOS2)

(see p.2 item 22)

Note: CLRCMOS2 allows you to clear the data in CMOS. The data in CMOS includes system

setup information such as system password, date, time, and system setup parameters. To

clear and reset the system parameters to default setup, please turn off the computer and

unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper

cap to short the Clear CMOS jumper for 5 seconds. After shorting the Clear CMOS jumper,

please remove the jumper cap. However, please do not clear the CMOS right after you

update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS,

you must boot up the system first, and then shut it down before you do the clear-CMOS

action.

J1 Jumper

(FID0, FID1, FID2, FID3, FID4)

(see p.2 item 29)

Note: The set of J1 Jumper allows users to adjust the multiplier of CPU. See page 14 of User

Manual in the Support CD for details. However, the system will work well without the

adjustment of multiplier. You do not have to adjust the multiplier for normal usage.

2-pin jumper

EnglishEnglish

English

1111

11

ASRock K7VT4A Pro Motherboard

2.5 Connectors2.5 Connectors

2.5 Connectors

Connectors are NOT jumpers. DO NOT place jumper caps over these

connectors. Placing jumper caps over the connectors will cause perma-

nent damage of the motherboard!

Connector Figure Description

FDD Connector

(33-pin FLOPPY1)

(see p.2 item 19)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

Primary IDE Connector (Blue) Secondary IDE Connector (Black)

(39-pin IDE1, see p.2 item 8) (39-pin IDE2, see p.2 item 7)

80-conductor, ATA 66/100/133 cable

Note: If you use only one IDE device on this motherboard, please set the IDE

device as “Master”. Please refer to the instruction of your IDE device vendor

for the details. Besides, to optimize compatibility and performance, please

connect your hard disk drive to the primary IDE connector (IDE1, blue) and

CD-ROM to the secondary IDE connector (IDE2, black).

Serial ATA Connectors These two Serial ATA (SATA)

(SATA1: see p.2 item 12) connectors support SATA data

(SATA2: see p.2 item 13) cables for internal storage

devices. The current SATA

interface allows up to 1.5 Gb/s

data transfer rate.

Serial ATA (SATA) Either end of the SATA data

Data Cable cable can be connected to the

SATA hard disk or the SATA

connector on the motherboard.

connect the black end

to the IDE devices

connect the blue end

to the motherboard

the red-striped side to Pin1

EnglishEnglish

English

SATA1 SATA2

1212

12

ASRock K7VT4A Pro Motherboard

Serial ATA (SATA) Please connect the black end of

Power Cable SATA power cable to the power

(Optional) connector on the drive. Then

connect the white end of SATA

power cable to the power

connector of the power supply.

USB 2.0 Header ASRock I/O Plus

TM

provides you

(9-pin USB67) 6 ready-to-use USB 2.0 ports on

(see p.2 item 18) the rear panel. If the rear USB

ports are not sufficient, this

USB 2.0 header is available to

support 2 extra USB 2.0 ports.

Shared USB 2.0 Header This USB45 connector is shared

(9-pin JUSB45) with the USB 2.0 ports 4,5 on

(see p.2 item 28) ASRock I/O Plus

TM

. When using

the front panel USB ports by

attaching the front panel USB

cable to this connector

(JUSB45), the USB ports 4,5 on

ASRock I/O Plus

TM

will not be able

to function.

Internal Audio Connectors These connectors allow you to

(4-pin CD1, 4-pin AUX1) receive stereo audio input from

(CD1: see p.2 item 20) sound sources such as a CD-

(AUX1: see p.2 item 21) ROM, DVD-ROM, TV tuner card,

or MPEG card.

Front Panel Audio Connector This is an interface for front panel

(9-pin AUDIO1) audio cable that allows conve-

(see p.2 item 24) nient connection and control of

audio devices.

System Panel Connector This connector accommodates

(9-pin PANEL1) several system front panel

(see p.2 item 16) functions.

CD1AUX1

EnglishEnglish

English

connect to the

power supply

connect to the SATA

HDD power connector

1313

13

ASRock K7VT4A Pro Motherboard

Chassis Speaker Connector Please connect the chassis

(4-pin SPEAKER 1) speaker to this connector.

(see p.2 item 17)

Chassis Fan Connector Please connect a chassis fan

(3-pin CHA_FAN1) cable to this connector and

(see p.2 item 15) match the black wire to the

ground pin.

CPU Fan Connector Please connect a CPU fan cable

(3-pin CPU_FAN1) to this connector and match the

(see p.2 item 2) black wire to the ground pin.

ATX Power Connector Please connect an ATX power

(20-pin ATXPWR1) supply to this connector.

(see p.2 item 6)

Power LED Connector Please connect a 3-pin power

(3-pin PWR_LED1) LED cable to this connector.

(see p.2 item14)

Game Connector Connect a Game cable to this

(15-pin GAME1) connector if the Game port

(see p.2 item 26) bracket is installed.

2.62.6

2.6

Serial ASerial A

Serial A

TT

T

A (SAA (SA

A (SA

TT

T

A) Hard Disks InstallationA) Hard Disks Installation

A) Hard Disks Installation

This motherboard adopts VIA VT8237 southbridge chipset that supports Serial

ATA (SATA) hard disks. You may install SATA hard disks on this motherboard for

internal storage devices. This section will guide you to install the SATA hard disks.

STEP 1: Install the SATA hard disks into the drive bays of your chassis.

STEP 2: Connect the SATA power cable to the SATA hard disk.

STEP 3: Connect one end of the SATA data cable to the motherboard’s SATA

connector.

STEP 4: Connect the other end of the SATA data cable to the SATA hard disk.

EnglishEnglish

English

1414

14

ASRock K7VT4A Pro Motherboard

2.72.7

2.7

Hot Plug and Hot Swap FHot Plug and Hot Swap F

Hot Plug and Hot Swap F

unctions for SAunctions for SA

unctions for SA

TT

T

A HDDsA HDDs

A HDDs

K7VT4A Pro motherboard supports Hot Plug and Hot Swap functions for SATA

devices.

NOTE

What is Hot Plug Function?

If the SATA HDDs are NOT set for RAID configuration, it is called “Hot

Plug” for the action to insert and remove the SATA HDDs while the

system is still power-on and in working condition.

However, please note that it cannot perform Hot Plug if the OS has

been installed into the SATA HDD.

What is Hot Swap Function?

If SATA HDDs are built as RAID1 then it is called “Hot Swap” for the

action to insert and remove the SATA HDDs while the system is still

power-on and in working condition.

2.82.8

2.8

Making An SAMaking An SA

Making An SA

TT

T

A Driver DiskA Driver Disk

A Driver Disk

etteette

ette

If you want to install Windows 2000 or Windows XP on your SATA HDDs, you will

need to make an SATA driver diskette before you start the OS installation.

STEP 1: Insert the ASRock Support CD into your optical drive to boot your system.

(Do NOT insert any floppy diskette into the floppy drive at this moment!)

STEP 2: During POST at the beginning of system boot-up, press <F11> key, and

then a window for boot devices selection appears. Please select CD-

ROM as the boot device.

STEP 3: When you see the message on the screen, “Do you want to generate

Serial ATA driver diskette [YN]?”, press <Y>.

STEP 4: Then you will see these messages,

Please insert a diskette into the floppy drive.

WARNING! Formatting the floppy diskette will

lose ALL data in it!

Start to format and copy files [YN]?

Please insert a floppy diskette into the floppy drive, and press <Y>.

STEP 5: The system will start to format the floppy diskette and copy SATA drivers

into the floppy diskette.

EnglishEnglish

English

1515

15

ASRock K7VT4A Pro Motherboard

Once you have the SATA driver diskette ready, you may start to install Windows 2000 /

Windows XP on your system directly without setting the RAID configuration on your

system, or you may start to use “VT8237 SATA RAID BIOS” to set RAID 0 / RAID 1 / JBOD

configuration before you install the OS. Before you start to configure the RAID function,

you need to check the installation guide in the Support CD for proper configuration. Please

refer to the document in the Support CD, “Guide to SATA Hard Disks Installation and RAID

Configuration”, which is located in the folder at the following path:

.. \ SATA RAID BIOS

You may also set the RAID configuration by using “VIA RAID Tool” in Windows environment.

Please refer to the document in the Support CD, “Guide to VIA RAID Tool”, which is located

in the folder at the following path:

.. \ VIA RAID Tool

3. BIOS Information3. BIOS Information

3. BIOS Information

The Flash Memory on the motherboard stores BIOS Setup Utility. When you start up

the computer, please press <F2> during the Power-On-Self-Test (POST) to enter

BIOS Setup utility; otherwise, POST continues with its test routines. If you wish to

enter BIOS Setup after POST, please restart the system by pressing <Ctl> + <Alt> +

<Delete>, or pressing the reset button on the system chassis.

The BIOS Setup program is designed to be user-friendly. It is a menu-driven program,

which allows you to scroll through its various sub-menus and to select among the

predetermined choices. For the detailed information about BIOS Setup, please refer

to the User Manual (PDF file) contained in the Support CD.

4. Software Suppor4. Software Suppor

4. Software Suppor

t CD informationt CD information

t CD information

This motherboard supports various Microsoft

®

Windows

®

operating systems: 98 SE/

ME / 2000 / XP. The Support CD that came with the motherboard contains necessary

drivers and useful utilities that will enhance motherboard features.

To begin using the Support CD, insert the CD into your CD-ROM drive. It will display

the Main Menu automatically if “AUTORUN” is enabled in your computer. If the Main

Menu does not appear automatically, locate and double-click on the file “ASSETUP.

EXE” from the “BIN” folder in the Support CD to display the menus.

EnglishEnglish

English

1616

16

ASRock K7VT4A Pro Motherboard

1717

17

ASRock K7VT4A Pro Motherboard

®

“

” “ ”

“ ”

“

”

1818

18

ASRock K7VT4A Pro Motherboard

1919

19

ASRock K7VT4A Pro Motherboard

2020

20

ASRock K7VT4A Pro Motherboard

“ ”

La page charge ...

ASROCK K7VT4A PRO Le manuel du propriétaire

ASROCK K7VT4A PRO Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents