Simplicity 071035-02 Guide d'installation

Marque: Simplicity

Modèle: 071035-02

Catégorie: Groupes électrogènes

Taper: Guide d'installation

Not for

Reproduction

100/150/200 Amp Automatic

Transfer Switch

with Service Disconnect and

AC Control Module

Installation and Operators Manual

Questions?

Help is just a moment away!

Call: Transfer Switch Helpline

800-743-4115 Monday - Friday 8:00 AM - 5:00 PM Central Time

80011170 Revision A

Not for

Reproduction

2 BRIGGSandSTRATTON.COM

Thank you for your purchase of this Briggs & Stratton® automatic transfer switch. This product is designed for use with specific home

standby generators and may not function with generators or remote modules produced by other manufacturers. Seek a qualified electrical

professional to determine applicability of this equipment to equipment manufactured by others. When operated and maintained according to

the instructions in this manual, your system will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with this system and how to avoid them.

We have made every effort to provide for a safe, streamlined and cost-effective installation. As each installation is unique, it is impossible

to know of and advise of all conceivable procedures and methods by which installation might be achieved. We do not know all possible

hazards and/or the results of each possible method or procedure. It is important that you read and understand these instructions thoroughly

before attempting to install or operate this equipment. Save these original instructions for future reference.

This transfer switch and optional remote modules require professional installation before use. Refer to the Installation section of this manual

and the installation instructions packaged with the remote modules for instructions on installation procedures. Only licensed electrical

contractors should install transfer switches and remote modules. Installations must strictly comply with all applicable federal, state and local

codes, standards and regulations. Your installer should follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your system. Consult your Yellow Pages. There are many

authorized service dealers who provide quality service. You can also contact Technical Service by phone at 800-743-4115 between 8:00 AM

and 5:00 PM CT, or click on Find a Dealer at BRIGGSandSTRATTON.COM, which provides a list of authorized dealers.

For Future Reference

Please fill out the information below and keep with your receipt to assist in unit identification for future purchase issues.

Not for

Reproduction

Table of Contents

Important Safety Instructions .............................4

Installation..........................................5

Home Owner Responsibilities ..........................................5

Owner Orientation ...................................................5

Installing Dealer/Contractor Responsibilities...............................5

Equipment Description ...............................................5

Delivery Inspection ..................................................6

Mounting Guidelines .................................................6

Power Wiring Interconnections .........................................7

Supervisory Control Terminals .........................................8

System Setup .....................................................10

Setting Dipswitches.................................................10

Supervisory Control Wiring ...........................................11

Testing the Automatic Transfer Switch ..................................11

Controls ...........................................12

Operation..........................................12

Enclosure Door ....................................................12

Troubleshooting .....................................13

Transfer Switch Schematic Diagram .......................14

Transfer Switch Wiring Diagram ..........................15

Product Specfications .................................16

Not for

Reproduction

4 BRIGGSandSTRATTON.COM

Save These Instructions

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation and maintenance of the equipment.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal injury

hazard. A signal word (DANGER, WARNING, or CAUTION) is used

with the alert symbol to designate a degree or level of hazard

seriousness. A safety symbol may be used to represent the type of

hazard. The signal word NOTICE is used to address practices not

related to personal injury.

DANGER indicates a hazard which, if not avoided, will result in

death or serious injury.

WARNING indicates a hazard which, if not avoided, could result

in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could result

in minor or moderate injury.

NOTICE addresses practices not related to personal injury.

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings in this

manual, and the tags and decals affixed to the unit are, therefore,

not all-inclusive. If you use a procedure, work method or operating

technique that the manufacturer does not specifically recommend,

you must satisfy yourself that it is safe for you and others. You

must also make sure that the procedure, work method or operating

technique that you choose does not render the equipment unsafe.

NOTICE Only qualified electricians should attempt installation

of this equipment, which must strictly comply with applicable

codes, standards and regulations.

WARNING Certain components in this product and related

accessories contain chemicals known to the State of California

to cause cancer, birth defects, or other reproductive harm. Wash

hands after handling.

NOTICE Improper treatment of equipment could damage it and

shorten its life.

• Use equipment only for intended uses.

• If you have questions about intended use, ask dealer or contact

Briggs & Stratton Power Products.

• Do not expose equipment to excessive moisture, dust, dirt, or

corrosive vapors.

• Remain alert at all times while working on this equipment. Never

work on the equipment when you are physically or

mentally fatigued.

• If connected devices overheat, turn them off and turn off their

circuit breaker/fuse.

Electrical Shock Read Manual

WARNING Shock Hazard. Installing low and high voltage

wire in same conduit could result in death, serious injury

and/or property damage.

• Do not run low and high voltage wire in the same conduit unless

the insulation rating on ALL wiring is rated for 600V. See NEC

for more information.

WARNING Failure to properly ground equipment could cause

electrocution resulting in death or seriousinjury.

• Do not touch bare wires.

• Do not use equipment with worn, frayed, bare or otherwise

damaged wiring.

• Do not handle electrical cords while standing in water, while

barefoot, or while hands or feet are wet.

• If you must work around a unit while it is operating, stand on an

insulated dry surface to reduce shock hazard.

• Do not allow unqualified persons or children to operate or

service equipment.

• In case of an accident caused by electrical shock, immediately

shut down all sources of electrical power and contact local

authorities. Avoid direct contact with the victim.

WARNING Shock hazard. Equipment contains high voltage

that could result in death, serious injury and/or

property damage.

• DO NOT operate this equipment imprudently or neglect its

maintenance.

Not for

Reproduction

Installation

We sincerely appreciate your patronage and have made significant

effort to provide for a safe, streamlined and cost-effective

installation. Because each installation is unique, it is impossible

to know of and advise the trade of all conceivable procedures and

methods by which installation might be achieved. Neither could we

know of possible hazards and/or the results of each method

or procedure.

For these reasons, only current licensed electrical professionals

should attempt system installations. Installations must strictly

comply with all applicable codes, industry standards and

regulations.

Your equipment is supplied with this Installation Manual and a

separate Operator’s Manual. These are important documents and

should be retained by the owner after the installation has

been completed.

Every effort has been made to make sure that the information

in this manual is both accurate and current. However, the

manufacturer reserves the right to change, alter or otherwise

improve the system at any time without prior notice.

Home Owner Responsibilities

To help you make informed choices and communicate effectively

with your installation contractor(s), read and understand Owner

Orientation before contracting or starting your

equipment installation.

To arrange for proper installation, contact the store at which you

purchased your equipment, your dealer, or your utility

power provider.

The equipment warranty is VOID unless the system is installed by

licensed electrical professionals.

Owner Orientation

The illustrations provided are for typical circumstances and are

meant to familiarize you with the installation options available with

your system.

Local codes, appearance, and distances are the factors that must

be considered when negotiating with an installation professional.

As the distance from the existing electrical service increases,

compensation in wiring materials must be allowed for. This is

necessary to comply with local codes and overcome electrical

voltage drops.

These factors will have a direct effect on the overall price of your

equipment installation.

Your installer must check local codes AND obtain permits before

installing the system.

• Read and follow the instructions given in this manual.

• Follow a regular schedule in caring for and using your

equipment, as specified in this manual.

Installing Dealer/Contractor Responsibilities

• Read and observe the Important Safety Instructions.

• Read and follow the instructions given in this manual.

• The installer may need to provide appropriate rated contactors

based on loads to be controlled.

• Discuss with owner their load priority preferences to decide

on remote module priority settings.

• Check federal, state and local codes and authority having

jurisdiction, for questions on installation.

• Ensure generator is not overloaded with selected loads.

If you need more information about the transfer switch, call

800-743-4115, between 8:00 AM and 5:00 PM CT.

Equipment Description

The transfer switch is designed to transfer selected loads found

in normal residential installations to standby power in the event

of a primary power outage. The load is connected either to utility

power (normal) or home standby power (generator). The transfer

switch monitors utility and generator voltages and will automatically

connect loads to the appropriate source of power.

Only a licensed electrician should complete a home standby

installation. Service conduit and conductors can be wired directly

from the watt-hour meter to the transfer switch. A separate service

entrance disconnect and associated wiring is not required when

installed per applicable federal, state and local codes, standards

andregulations.

Major components of the transfer switch are a 2 pole utility

disconnect circuit breaker, a 2 pole generator disconnect circuit

breaker, a 2 pole double throw transfer switch, transfer switch

control circuit board, fused utility terminals and interconnecting

wiring. All of these components are housed in a NEMA3R

enclosure that is suitable for both indoor and outdoor installations.

The transfer switch is solenoid-operated from utility or generator

inputs and contain suitable mechanical and electrical interlock

switches to eliminate the possibility of connecting the utility service

to the generator output. It has ratings capable of switching full

utility power into the residence. In addition, a manual override lever

is provided for the transfer function.

Not for

Reproduction

6 BRIGGSandSTRATTON.COM

The transfer switch control board has active circuits sensing utility

and generator voltages. It creates a signal for generator start-up,

switch transfer and retransfer when utility is restored. The transfer

switch control board provides status LED’s to indicate the power

source available.

Delivery Inspection

After opening the carton, carefully inspect the transfer

switch components for any damage that may have occurred

duringshipment.

If loss or damage is noted at time of delivery, have the person(s)

making delivery note all damage on the freight bill and affix his

signature under the consignor’s memo of loss or damage. If loss

or damage is noted after delivery, contact the carrier for claim

procedures. Missing or damaged parts are not warranted.

Shipment contents:

• Automatic transfer switch

• Installation and operator’s manuals

• Current transformers (2)

To be supplied by installer:

• Connecting wire and conduit

• Various specialty tools/equipment

Mounting Guidelines

The transfer switch system circuitry is enclosed in a NEMA Type3R

enclosure suitable for indoor/outdoor use. Guidelines for mounting

the enclosure include:

• Install enclosure on a firm, sturdy supporting structure.

• The transfer switch enclosure must be installed with

minimum NEMA3R hardware for conduit connections.

• To prevent switch contact distortion, level and plumb the

enclosure. This can be done by placing washers between the

enclosure and the mounting surface.

• NEVER install the switch or remote modules where any

corrosive substance might drip onto the enclosure.

• Protect the switch at all times against excessive moisture,

dust, dirt, lint, construction grit and corrosivevapors.

A typical automatic transfer switch installation is depicted on

the next page. Examples of remote module installations are also

shown. It is best if the transfer switch is mounted near the utility

meter, either inside or outside. The remote module can be located

anywhere between the main distribution panel and its connected

load, either inside or outside. The remote module must be

accessible for service. Discuss layout suggestions/ changes with

the owner before beginning the system installation process

NOTICE Before drilling conduit entry holes, or any other holes,

cover and protect the switch and electronics to prevent dirt and

metal fragments from entering the mechanical and electrical

components. Failure to do so may result in damage or malfunction

of the switch.

NOTICE Use a vacuum to clean any dirt or metal shavings inside

the transfer switch. Do not use a blower or compressed air to clean

the inside of the transfer switch because debris may become lodged

in the electrical and mechanical components causing damage or

malfunction.

Main

Distribution

Panel

Transfer Switch

w/ Service

Disconnect

Hot Water

Heater

Air

Conditioner

Generator

Watt -

Hourmeter

Service Disconnect

Branch

Circuits

Not for

Reproduction

Power Wiring Interconnections

NOTICE Improper installation could cause damage to the circuit

boards and shorten their life. Installing circuit boards in live

circuits will damage the board and is not covered by warranty.

ALWAYS disconnect ALL sources of power prior to servicing.

• Remove all power prior to installing this equipment. Failure to

do so could cause internal damage to the board when making

electrical connections.

• Turn generator to OFF position.

• Turn off utility power to the standby generator and

transferswitch.

All wiring must be the proper gauge, properly supported and

protected by conduit. All wiring should be done per applicable

federal, state and local codes, standards and regulations. Obey

wire type and torque specifications printed on the terminal blocks,

neutral/ground connectors, and installation instructions.

Use installer supplied 600VAC or greater copper or aluminum wire

of a gauge that complies with the latest version of the National

Electric Code to complete the following connections between utility

power, transfer switch, generator, main distribution panel, and

optional remote modules. Apply the necessary correction factors

and wire size calculations.

1. Set generator’s circuit breaker to OFF position.

2. Set generator’s system switch to OFF position.

3. Remove 15 Amp fuse from generator control panel.

4. Turn off utility power to the standby generator and

transfer switch.

5. Connect utility service to transfer switch’s utility

service disconnect circuit breaker terminals marked

“UTILITYCONNECTION”.

6. Connect utility service neutral to transfer switch

neutralterminal.

7. Connect main distribution panel feeder conductors to transfer

switch terminals marked “LOADCONNECTION”.

8. NOTICE Connect main distribution panel neutral to transfer

switch neutral terminal.

9. Connect main distribution panel ground to transfer switch

“GND” terminal.

Assure grounding electrode conductor is connected and

bonded per applicable federal, state and local codes,

standards and regulations.

10. Connect feeder conductors from transfer switch

“GENERATOR CONNECTION” terminals to generator circuit

breaker LINE1 and LINE2 terminals. Each conductor must

pass through hole of current transformer before making

connection.

11. Plug current transformer leads into “CT1” and “CT2”

terminals (C) on transfer switch control board.

240V

120V

Neutral

Ground

To Transfer Switch

Line 1 Neutral

Ground

Line 2

Generator

Circuit

Breaker

CT1

CT2

DPSW2

DPSW1

WARNING Shock Hazard. Installing low and high voltage

wire in same conduit could result in death, serious injury

and/or property damage.

• Do not run low and high voltage wire in the same conduit unless

the insulation rating on ALL wiring is rated for 600V. See NEC

for more information.

WARNING Shock Hazard. Failure to properly wire equipment could

cause electrocution resulting in death or seriousinjury.

•

DO NOT connect the ground conductor to the neutral connection in the

remote module.

• All modules must have a dedicated neutral connection.

Not for

Reproduction

8 BRIGGSandSTRATTON.COM

12. Connect conductor from transfer switch neutral terminal to

generator NEUTRAL terminal. Observe generator control panel

labeling for terminalidentification.

13. Connect conductor from transfer switch “GND” terminal to

generator control panel “GROUND” terminal.

Assure generator equipment grounding conductor is

connected per applicable federal, state and local codes,

standards and regulations.

14. Using minimum #14 AWG conductors, connect the transfer

switch “UTILITY 240 VAC” terminals (A) to generator’s “240

VAC” terminals via two-pole connector (B) supplied with

generator.

15. Using minimum #18 AWG twisted pair copper or aluminum

conductors, no greater than 200 ft. in length, 300 volt

75°C-90°C, connect “T/R” and “GND” terminals on transfer

switch control board (B) to the generator’s control panel (A)

“TxRx” and “TxRx GND” terminals via ten pin connector or

eight pin terminal. Count down to the proper pin location on

the generator control board since visual alignment with its

decal can bemisleading:

16. Tighten all wire connections/fasteners to proper torque.

See label inside transfer switch enclosure or values listed in

remote module installation instructions for proper

torque values.

The illustration on the following page shows a completed transfer

switch installation. Your actual layout will vary.

Illustration callouts are:

A - From utility watt-hour meter

B - Current transformers

C - Transfer switch enclosure

D - T/R and GND to Generator

E - Transfer switch control board

F - Neutral terminal

G - Neutral bus

H - Ground bus

J - Main distribution panel

K - UTILITY 240VAC to Generator

L - Two pin connector or Two pin terminal block

M - Ten pin connector or Eight pin terminal block

N - Generator circuit breaker

P - Generator

R - Generator Neutral terminal

S - Generator Ground terminal

T - Transfer switch ground terminal

U - Load connection to distribution panel

V - Utility disconnect circuit breaker

W - Utility connection

X - Generator connection

Not for

Reproduction

Typical Transfer Switch shown

LINE1

LINE2

240

VAC

J H

Not for

Reproduction

10 BRIGGSandSTRATTON.COM

System Setup

You must perform the following before operating the system:

• If generator is installed in an area regularly subjected to

temperatures below 40°F (4°C), select a 50 second warm up

time by moving jumper JP2 (C) installed on transfer switch

control board from ‘20’ position to ‘50’position.

• Set the DPSW1 (A) and DPSW2 (B) dipswitches on the

transfer switch control board to match the kW rating of the

home standby generator, as described in SettingDipswitches.

Setting Dipswitches

Dipswitches are used to adjust control board operation based

on generator capacity. DPSW1 and DPSW2 switches are set to

correspond to total system kW rating. Dipswitch DPSW1 (A) has

units of 1,000 watts; Dipswitch DPSW2 (B) has units of

10,000 watts.

Set dipswitches with power removed from the transfer switch to

ensure proper control system operation. If dipswitches are set

when power is present at transfer switch, a power reset needs to be

performed before the new dipswitch settings will take effect. Power

reset is when all power is removed from the transfer switch and

then reintroduced after 30 seconds.

NOTICE A transfer switch fault message will occur on standby

generator control board if dipswitches are not properly established

as noted above.

To properly establish the dipswitches, make sure that only one

dipswitch is set to “ON” position for DPSW1 and one dipswitch for

DPSW2. For example a 20kW generator, set DPSW2 dipswitch

20 to “ON” position and DPSW1 dipswitch 0 to “ON” position.

20,000 plus 0 equal 20,000 watts.

The “On” position for the dipswitches is the switch number ON

THE TRANSFER SWITCH CONTROL BOARD, not on the switch. For

example, for an 18,000 watt generator, set DPSW2 dipswitch 10 to

“On” position. Set DPSW1 dipswitch 8 to “On” position. 10,000 plus

8000 equals 18,000 watts.

Set only one switch to “On” position

on DPSW1 andDPSW2.

Refer to following chart for proper switch selection(s).

NOTICE

Air density is less at high altitudes, resulting in less

available engine power. Specifically, engine power will decrease 3.5%

for each 1,000 feet (300 meters) above sea level and 1% for each 10°

F (5.6°C) above 77°F (25°C). Generators located in these conditions

must have the transfer switch programmed appropriately for this

power decrease.

NOTICE Use extreme caution when setting dipswitches or

damage to control board will result.

• Use a pencil or small piece of plastic to set the dipswitch.

• NEVER use a screwdriver or any type of metal object to set

dipswitches.

CT1

CT2

DPSW2

DPSW1

CA B

kW Rating

Generator

DPSW

#1 “ON”

Position

DPSW

#2 “ON”

Position

7kW 7 0

8kW 8 0

9kW 9 0

10kW* 0 10

11kW* 1 10

12kW 2 10

13kW* 3 10

14kW 4 10

15kW 5 10

16kW 6 10

17kW 7 10

18kW 8 10

19kW 9 10

20kW 0 20

30kW 0 30

45kW 5 40

48kW 8 40

50kW 0 50

60kW 0 60

* For generators with a rating that includes 500 Watts, round down to

next lowest rating

(example: 13.5 kW set to 13kW)

Not for

Reproduction

Supervisory Control Wiring

An air conditioner can be used with the supervisory contacts

on either terminals A-A or B-B. Terminals A-A can only be

used with supervisory control. Large loads can only be used

with contactor control on terminals B-B. Examples of each

system are described below.

1. The terminal strip on control module in transfer switch

has four connections for customer use. There are two

sets of “Normally Closed” contacts available. They will

be activated when generator power is required. These

can be used for supervisory control of large connected

loads on generator. Loads will be allowed to operate if

there is enough generator power available.

NOTE: There are two wireways provided to keep the

supervisory loads separated from each other.

2. Terminals “A-A” on control module are rated for

24VAC and air conditioner contactor control. Contacts

are connected in series with the air conditioner

contactor control circuit.

3. Terminals “B-B” on control module are rated for 1Amp

125 VAC and installer supplied contactor to control

a large load, such as an electric hot water heater.

Contacts are connected in series with the contactor

controlcircuit.

4. Tighten all wire connections/fasteners to proper torque.

See label inside transfer switch enclosure for proper

torquevalues.

Testing the Automatic Transfer Switch

Turn the utility service disconnect circuit breaker feeding the

transfer switch contactor to the OFF position. The system’s

automatic sequence described below will initiate. To return to utility

power, turn the utility service disconnect circuit breaker to the

ON position.

Utility Fail

The generator senses when utility voltage is below 70percent of

nominal. Engine start sequence is initiated after 6second time

delay.

Engine Warm-Up

Time delay to allow for engine warm-up before transfer. Use jumper

on transfer switch control board to select delay of

20seconds or 50 seconds.

Transfer

Transfer from utility to generator supply occurs after voltage is

above set levels. The transfer switch control board LED lights will

change from green (utility) to red (generator) and the Symphony II

status light will change blink status from Blink Blink_Pause_Blink

Blink to Blink_Pause_Blink. Minimum engine run time is 5 minutes

after transfer.

Utility Pickup

Voltage pickup level is 80 percent of nominal voltage.

Retransfer

Retransfer from generator to utility power is approximately 10

seconds after utility voltage supply is above pickup level and

minimum run time is completed. All remote module(s) will remain

OFF for five minutes after the power transfer.

Engine Cool Down

Engine will run for 60 seconds after retransfer.

WARNING Shock Hazard. Equipment contains high voltage

that could cause electrocution resulting in death or

serious injury.

• Testing must only be performed by qualified personnel.

• Do not operate this equipment imprudently, carelessly or neglect

its maintenance.

Air Conditioner Contactor

24 VAC

Contactor

Neutral

120 VAC

Not for

Reproduction

12 BRIGGSandSTRATTON.COM

Controls

Other than a Manual Override lever, there are no operator controls

because this is an automatic transfer switch. The manual override

is to be used only by licensed professionals. Information on handle

use can be obtained by calling Technical Service at 800-743-4115.

Operation

To select automatic transfer operation, do the following:

1. In transfer switch, set utility disconnect circuit breaker

to ON position.

2. In transfer switch, set generator disconnect circuit breaker to

ON position.

3. Install 15 Amp fuse in generator’s control panel.

4. Set generator’s circuit breaker to ON position.

5. Set generator’s system switch to AUTO position.

The system will now be in automatic operation mode.

When the generator is providing power to the transfer switch, the

control module is constantly monitoring generator power. If the air

conditioner is called to run, and there is sufficient generator power

available, the controller will close contacts “A-A” to air conditioner

contactor. Contacts “B B” will open before contacts A-A close. If

loads are too great for the generator, contacts A-A and/or B-B will

open. When air conditioning is not needed, A-A will open. If enough

power is available, B-B will close.

Enclosure Door

To open the transfer switch door, remove the two exterior

thumb screws (A) and carefully lift off door.

To close and secure the door, push door closed against

enclosure making sure that the tab on the enclosure fits into

the slot on the door. While in this position, the door can

rest on the tab (B) at the bottom of the enclosure. Reinstall

both thumb screws to finger tight. Enclosure door MUST be

closed and secured at all times except when system is being

serviced.

When Calling for Assistance

You must have the Model Number and Serial Number from each

transfer switch or remote module ID label at hand if it is necessary

to contact a local service center regarding service or repair. Obtain

this information from the unit ID labels located on or inside device.

For convenience, record the information on the inside front cover of

this manual.

To contact Briggs & Stratton call 800-743-4115, between 8:00 AM

and 5:00 PM CT.

Installation Inspection

Before placing the system into service, inspect the entire installation

carefully.

Not for

Reproduction

Troubleshooting

Problem Cause Correction

Automatic transfer switch does not

transfer to generator

1. Generator breaker open.

2. Generator voltage not acceptable.

1. Reset generator circuit breaker.

2. Refer to generator manual.

Automatic transfer switch does not

transfer to utility

1. Utility disconnect circuit breaker open in

transfer switch.

2. Utility voltage not acceptable.

1. Reset utility disconnect circuit breaker in

transfer switch.

2. Wait for utility voltage to return tonormal.

Generator is still running after switch

transfers to utility power

Engine cool down period. Engine should stop after 1 minute.

Generator or supervised loads (air

conditioner, etc.) are operating

improperly when generator is

supplyingpower

1. A-A or B-B contacts not

operatingcorrectly.

2. Too much load on generator.

3. Current transformer not connected.

4. Broken current transformer.

1. Check A-A or B-B contacts for

proper operation and/or check

control wiring to external load.

2. Decrease load to generator.

3. Plug CT connectors into

controlmodule.

4. Contact local authorized

servicecenter.

Generator is still running after utility

power is restored

1. Minimum engine run time has notelapsed.

2. Fuse(s) in transfer switch isdefective.

1. Wait five minutes for transfer switch to

retransfer to utility power.

2. Contact local authorized servicecenter.

Not for

Reproduction

14 BRIGGSandSTRATTON.COM

Transfer Switch Schematic Diagram

UTILITY

SUPPLY

240 VAC

TO GENERATOR

UTILITY

240 VAC

FUSE

WIRE SCHEMATIC

NEUTRAL

TRANSFER SWITCH

127

556

205 206

CONTROL BOARD

CT1CT2

GND

T/R

N.O.

N.C.

V+

J2 J1 J4J3 J5J6

SYMPHONY II

CONTROLLER

ORG

WHT

YLW

BLK

RED

128

MAIN BREAKER

PANEL

GENERATOR

SUPPLY

240 VAC

MAIN

BREAKER PANEL

Optional

Not for

Reproduction

Transfer Switch Wiring Diagram

TO UTILITY SUPPLY

NEUTRAL

TO GENERATOR

MAIN

BREAKER

PANEL

UTILITY

240 VAC

FUSE

HOLDER

CONTROL BOARD

MAIN BREAKER

PANEL

206

128

RANSFER

SWITCH

127

556

205

CIRCUIT

BREAKER

SERVICE

DISCONNECT

GENERATOR

WIRE DIAGRAM

Optional

SYMPHONY II

CONTROLLER

WHT

BLK

RED

ORGYLW

CT1

CT2

GND

T/R

N.O.

N.C.

V+

GENERATOR

SERVICE

DISCONNECT

Not for

Reproduction

16 BRIGGSandSTRATTON.COM

Automatic Transfer Switch

Product Specfications

Model 071046

Series 200SED

Rated Maximum Load Current

a 25°C (77°F)* ..............................................................200 Amps

Rated AC Voltage. ..............................................................250 Volts

Poles ............................................................................................... 2

Frequency ................................................................................60 Hz

Fault Current Rating ..........25,000 RMS Symmetrical Amperes on Utility Side

................................. 10,000 RMS Symmetrical Amperes on Generator Side

Normal Operating Range ...............-28.8°C (-20°F) to 40°C (104°F)

Weight ........................................................................27 kg (59 lbs)

Model 071036