Simplicity 076052-00 Guide d'installation

GE Generator Systems

Liquid-Cooled

Generator System

Installation and

Start-Up Manual

NOT

FOR REPRODUCTION

2

Thank you for purchasing this quality-built GE generator. We’re pleased that you’ve placed your confidence in the GE

brand. When operated and maintained according to the instructions in the operator’s manual, your generator will

provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with generator

systems and how to avoid them. This generator system is designed and intended only for use as an optional standby

system that provides an alternate source of electric power and to serve loads such as heating, refrigeration systems,

and communication systems that, when stopped during any power outage, could cause discomfort or inconvenience.

Save these original instructions for future reference.

This standby generator requires professional installation before use. The installer should follow the

instructions completely. Installations must strictly comply with all applicable codes, industry standards and regulations.

Where to Find Us

You never have to look far to find support and service for your generator. For quick service when you need it

most fill out the information below and keep your original receipt with this manual. You may contact Customer

Service, toll-free at 888‑575‑8226 between 8:00 AM and 5:00 PM CT., or click on SERVICE & SUPPORT at

www.homestandbygeneratorsystems.com, which provides a list of authorized dealers.

For Future Reference

Please fill out the information below and keep with your receipt to assist in unit identification for future purchase issues.

Date of Purchase: _____________________________

Generator

Model Number _____________________________

Model Revision _____________________________

Serial Number _____________________________

Engine

Serial Number _____________________________

NOT

FOR REPRODUCTION

3

Table of Contents

Safety Rules................................................4

Installation ................................................7

Owner Responsibilities ......................................

7

Installing Dealer/Contractor Responsibilities............................7

Unpacking Precautions................................................7

Shipment Contents ...................................................8

Installation Checklist..................................................8

Generator Placement .................................................9

Exhaust Side of Generator.............................................9

Placement of Standby Generator to

REDUCE THE RISK OF CARBON MONOXIDE POISONING ..................10

Placement of Standby Generator to REDUCE THE RISK OF FIRE...........12

Other General Location Guidelines ....................................16

Electrical and Fuel Inlet Locations.....................................17

The Gaseous Fuel System ............................................20

Fuel Pipe Sizing......................................................21

Fuel Conversion .....................................................21

Fuel Pressure........................................................21

Power Loss..........................................................21

Fuel Consumption ...................................................22

System Connectors ..................................................23

Grounding the Generator.............................................25

Final Installation Considerations ......................................27

Initial Start‑up (No Load) .............................................28

Operation.................................................29

Automatic Operation Sequence .......................................29

Setting Exercise Timer ...............................................29

Installation Inspection ...............................................30

Schematic Diagram..................................................31

Wiring Diagram .....................................................39

NOT

FOR REPRODUCTION

4

Safety Rules

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation and maintenance of the generator and batteries.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a degree

or level of hazard seriousness. A safety symbol may be used

to represent the type of hazard. The signal word NOTICE is

used to address practices not related to personal injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE addresses practices not related to personal injury.

Important Safety Instructions

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings

in this manual, and the tags and decals affixed to the unit

are, therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that it

is safe for you and others. You must also make sure that the

procedure, work method or operating technique that you

choose does not render the generator system unsafe.

Fire

Toxic Fumes

Explosive Pressure

Rotating Fan Blade

Lift Hazard Read Manual

Exploding BatteryRotating Belt/Pulley

Chemical BurnAuto Start

Hot SurfaceRotating Parts

Electrical ShockExplosion

WARNING Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide could result in death, serious

injury, headache, fatigue, dizziness, vomiting, confusion,

seizures, nausea or fainting.

• Operate this product ONLY outdoors in an area that will not

accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors, ventailation

intakes, soffit vents, crawl spaces, open garage doors or other

openings that can allow exhaust gas to enter inside or be drawn

into a potentially occupied building or structure.

• Carbon monoxide detector(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions/

recommendations. Smoke alarms cannot detect carbon

monoxide gas.

WARNING The engine exhaust from this product contains

chemicals known to the State of California to cause cancer, birth

defects, or other reproductive harm.

WARNING Certain components in this product and related

accessories contain chemicals known to the State of California

to cause cancer, birth defects, or other reproductive harm. Wash

hands after handling.

NOT

FOR REPRODUCTION

5

WARNING Storage batteries give off explosive hydrogen gas

during recharging.

Slightest spark will ignite hydrogen and

cause explosion, resulting in death, serious

injury and/or property damage.

Battery electrolyte fluid contains acid and is extremely caustic.

Contact with battery contents could cause severe chemical burns.

A battery presents a risk of electrical shock and high short

circuit current.

• DO NOT dispose of battery in a fire. Recycle battery.

• DO NOT allow any open flame, spark, heat, or lit cigarette during

and for several minutes after charging a battery.

• DO NOT open or mutilate the battery.

• Wear protective goggles, rubber apron, rubber boots and

rubber gloves.

• Remove watches, rings, or other metal objects.

• Use tools having insulated handles.

WARNING Generator produces hazardous voltage.

Failure to properly ground generator could result

in electrocution.

Failure to isolate generator from power utility could result

in death or serious injury to electric utility workers due to

backfeed of electrical energy.

• DO NOT touch bare wires or bare receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT handle generator or electrical cords while standing in

water, while barefoot, or while hands or feet are wet.

• If you must work around a unit while it is operating, stand on an

insulated dry surface to reduce the risk of a shock hazard.

• DO NOT allow unqualified persons or children to operate or

service generator.

• In case of an accident caused by electrical shock, immediately

shut down the source of electrical power and contact the local

authorities. Avoid direct contact with the victim.

• Despite the safe design of the residential generator, operating

this equipment imprudently, neglecting its maintenance or being

careless could cause possible injury or death.

• Remain alert at all times while working on this equipment.

Never work on the equipment when you are physically or

mentally fatigued.

• Before performing any maintenance on the generator, disconnect

the battery cable indicated by a NEGATIVE, NEG or (‑) first. When

finished, reconnect that cable last.

• After your system is installed, the generator may crank and start

without warning any time there is a power failure. To prevent

possible injury, always set the generator’s system switch to OFF,

remove the service disconnect from the disconnect box AND

remove the 15 Amp fuse BEFORE working on the equipment.

WARNING Propane and Natural Gas are extremely flammable

and explosive, which could cause burns, fire or

explosion resulting in death, serious injury and/or

property damage.

• Install the fuel supply system according to NFPA 37 and other

applicable fuel-gas codes.

• Before placing the generator into service, the fuel system lines

must be properly purged and leak tested.

• After the generator is installed, you should inspect the fuel

system periodically.

• NO leakage is permitted.

• DO NOT operate engine if smell of fuel is present or other

explosive conditions exist.

• DO NOT smoke around the generator. Wipe up any oil spills

immediately. Ensure that no combustible materials are left in the

generator compartment. Keep the area near the generator clean

and free of debris.

WARNING Hazardous Voltage - Contact with power lines could

cause electric shock or burn, resulting in death or

serious injury.

Lifting Hazard / Heavy Object - Could result in

serious injury.

• If lifting or hoisting equipment is used, DO NOT contact any

power lines.

• DO NOT lift or move generator without assistance.

• Use lifting pipes as described in Lifting the Generator.

• DO NOT lift unit by roof as damage to generator will occur.

WARNING Moving parts could crush and cut.

Starter and other rotating parts

could entangle hands, hair, clothing,

or accessories resulting in serious injury.

• NEVER operate generator without protective housings, covers, or

guards in place.

• DO NOT wear loose clothing, jewelry or anything that could be

caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

• Before servicing, remove 15 Amp fuse from control panel and

disconnect Negative (NEG or ‑) battery cable.

NOT

FOR REPRODUCTION

6

CAUTION Excessively high operating speeds could result in

minor injury and/or equipment damage.

Excessively low speeds impose a heavy load on generator.

• DO NOT tamper with governed speed. Generator supplies correct

rated frequency and voltage when running at governed speed.

• DO NOT modify generator in any way.

WARNING Exhaust heat/gases could ignite combustibles

or structures resulting in death, serious injury and/or property

damage.

Contact with muffler area could cause burns resulting in

serious injury.

• DO NOT touch hot parts and AVOID hot

exhaust gases.

• Allow equipment to cool before touching.

• Exhaust outlet side of weatherproof enclosure must have at least

5 ft. (1.5m) minimum clearance from any structure, shrubs, trees

or any kind of vegetation.

• Standby generator weatherproof enclosure must be at least

5 ft. (1.5m) from windows, doors, any wall opening, shrubs or

vegetation over 12 inches (30.5 cm) in height.

• Standby generator weatherproof enclosure must have a minimum

of 5 ft. (1.5 m) overhead clearance from any structure, overhang,

or trees.

• DO NOT place weatherproof enclosure under a deck or other type

of structure that may confine airflow.

• Use only flexible fuel line provided. Connect provided fuel line to

generator. DO NOT use with or substitute any other flexible

fuel line.

• Smoke detector(s) MUST be installed and maintained indoors

according to the manufacturer’s instructions/recommendations.

Carbon monoxide alarms cannot detect smoke.

• Keep at least minimum distances shown in General Location

Guidelines to insure for proper generator cooling and

maintenance clearances.

• Replacement parts must be the same and installed in the same

position as the original parts.

WARNING Hot pressurized coolant could cause serious injury

and/or property damage.

• DO NOT open radiator cap when hot.

• Before servicing, allow coolant to cool.

CAUTION Installing the 15A fuse could cause the engine

to start at any time without warning resulting in minor or

moderate injury.

• Observe that the 15 Amp fuse has been removed from the control

panel for shipping.

• DO NOT install this fuse until all plumbing and wiring has been

completed and inspected.

NOTICE Improper treatment of generator could damage it and

shorten its life.

• Use generator only for intended uses.

• If you have questions about intended use, contact your

authorized dealer.

• Operate generator only on level surfaces.

• Adequate, unobstructed flow of cooling and ventilating air is

critical to correct generator operation.

• The access panels/door must be installed whenever the unit

is running.

• DO NOT expose generator to excessive moisture, dust, dirt, or

corrosive vapors.

• Remain alert at all times while working on this equipment.

Never work on the equipment when you are physically or

mentally fatigued.

• DO NOT start engine with air cleaner or air cleaner cover removed.

• DO NOT insert any objects through cooling slots.

• DO NOT use the generator or any of its parts as a step. Stepping

on the unit could cause stress and break parts. This may result in

dangerous operating conditions from leaking exhaust gases, fuel

leakage, oil leakage, etc.

• If connected devices overheat, turn them off and disconnect them

from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively;

-unit makes unusual noises.

NOTICE Exceeding generators wattage/amperage capacity could

damage generator and/or electrical devices connected to it.

• Start generator and let engine stabilize before connecting

electrical loads.

NOT

FOR REPRODUCTION

7

 • Readandfollowtheinstructionsgiveninthe

Operator’s Manual.

 • Followaregularscheduleinmaintaining,caring

for and using your generator, as specified in the

Operator’s Manual.

Owner Responsibilities

The system is equipped with an optional water heater that is

activated when ambient temperature is less than 80°F AND

utility power is present at the transfer switch.

If you need more information on this matter, please call

888-575-8226, between 8:00 AM and 5:00 PM CT.

 • Readandobservethesafetyrules.

 • InstallonlyanULapprovedtransferswitchthatis

compatible with the generator.

 • Readandfollowtheinstructionsgiveninthis

Installation and Start-up Manual.

 • Installationmuststrictlycomplywithallapplicable

codes, industry standards, laws, and regulations.

 • Allowsufficientroomonallsidesofgeneratorfor

maintenance and servicing.

Installing Dealer/Contractor Responsibilities

The unit is shipped ready for installation on a prepared

reinforced cement slab or engineered base. Avoid

damage from dropping, bumping, collision, etc. Store and

unpack carton with the proper side up, as noted on the

shipping carton.

Unpacking Precautions

Installation

This product is intended for use as an optional generator

system which provides an alternate source of electric power

and to serve loads such as heating, refrigeration systems,

and communication systems that, when stopped during any

power outage, could cause discomfort or inconvenience. This

product does not qualify for emergency standby as defined

by NFPA 70 (NEC).

Every effort has been made to ensure that information in this

manual is accurate and current. However, we reserve the

right to change, alter, or otherwise improve the product and

this document at any time without prior notice.

Only current licensed electrical and plumbing

professionals should attempt generator system

installations. Installations must strictly comply with all

applicable codes, industry standards and regulations.

After removing the carton, carefully inspect the generator for

any damage that may have occurred during shipment.

If loss or damage is noted at time of delivery, have the

person(s) making delivery note all damage on the freight bill

and affix his signature under the consignor’s memo of loss or

damage. If loss or damage is noted after delivery, separate

the damaged materials and contact the carrier for claim

procedures. Missing or damaged parts are not warranted.

Delivery Inspection

NOT

FOR REPRODUCTION

8

The generator system is supplied with:

 • Fully-servicedcoolantsystem

 • Fully-servicedoil/lubricatingsystem

 • Flexiblefuelhook-uphose

 • Installationandstart-upmanual

 • Operator’smanual

 • Accessdoorkeys

 • Spare15AmpATO-typefuse

 • Ten-pincontrolpanelconnector

 • Touchuppaint

 • RemoteLEDindicatorkit(LED/plate/screws)

Not Supplied:

 • Carbonmonoxidedetector(s)

 • Smokedetector(s)

 • Startingbattery

 • Reinforcedconcretepad

 • Connectingwireandconduit

 • Fuelsupplyvalves/plumbing

 • Two60”lengthsof2”Schedule40pipe(NOTconduit)

for lifting

 • Crane,liftingstraps,chainsorcables

 • Holepunchesfor7gasteel

 • Torquescrewdriver,5to50inch-poundrange

 • Voltage/frequencymeter

 • Variouscommonandspecialtoolsandequipment

Shipment Contents

Proper installation of the generator requires the completion

of the following tasks:

Carbon Monoxide (CO) Detector

Carbon Monoxide (CO) detector in working order.

Smoke Detector in working order.

Placement

Required permits have been obtained.

Generator placed in a Carbon Monoxide (CO) safe zone.

See Placement of Standby Generator to Reduce the

Risk of Carbon Monoxide Poisoning.

Generator placed in a fire safe zone. See Placement of

Standby Generator to Reduce the Risk of Fire.

Generator placed in a water damage safe zone. See

Other General Location Guidelines.

Generator placed in a utility safe zone. See Other

General Location Guidelines.

Generator placed in a debris free zone. See Other

General Location Guidelines.

Fuel

Generator is connected to fuel source with flexible fuel

line, has no fuel leaks and conforms to local codes. See

The Gaseous Fuel System.

Proper fuel pressure has been measured with all gas

appliances operating. See The Gaseous Fuel System.

Electrical

Generator neutral is connected to Automatic

Transfer Switch. See Generator AC Connection

System.

Generator is grounded. See Grounding the

Generator.

Generator is connected to the transfer switch with

the specified wiring. See Utility Circuit Connection

and Transfer Switch Communication.

Generator is connected to the transfer switch with

the specified wiring. #18AWG twisted pair wiring

from the generator control panel to the transfer

switch is installed in a separate conduit from

high voltage wires unless the insulation rating on

all wiring is rated for 600V See Transfer Switch

Communication.

Dipswitches in most transfer switches must be set

to correspond to the wattage of the generator. See

Transfer Switch Operator/Installation Manual.

Operation

Correct battery type is installed and fully charged.

See Final Installation Considerations.

Generator engine oil level is at full mark. See Final

Installation Considerations.

Utility was shut off to test the operation of generator

and transfer switch. Note any fault codes and make

corrections as required.

Installation Checklist

NOT

FOR REPRODUCTION

9

Before installing the generator, consult with the owner and

convey the following requirements, which must be satisfied

before the installation is complete.

There are two equally important safety concerns in regards

to carbon monoxide poisoning and fire. There are also

several general location guidelines that must be met before

the installation is considered complete.

Generator Placement

WARNING Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide could result in death, serious

injury, headache, fatigue, dizziness, vomiting, confusion,

seizures, nausea or fainting.

• Operate this product ONLY outdoors in an area that will not

accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors, ventailation

intakes, soffit vents, crawl spaces, open garage doors or other

openings that can allow exhaust gas to enter inside or be drawn

into a potentially occupied building or structure.

• Carbon monoxide detector(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions/

recommendations. Smoke alarms cannot detect carbon

monoxide gas.

Exhaust Side of Generator

 • Exhaustoutletsideofweatherproofenclosure

 • Weatherproofenclosureoppositeexhaustside

A

B

A

NOT

FOR REPRODUCTION

10

Placement of Standby Generator to REDUCE THE RISK OF CARBON MONOXIDE POISONING

The arrows in the figure below point to POTENTIAL points of entry for Carbon Monoxide Gas.

All fossil fuel burning equipment, such as standby

generators, contains carbon monoxide (CO) gas in the engine

exhaust. CO gas is odorless, colorless and tasteless and is

unlikely to be noticed until a person is overcome. CO gas can

kill you so it is required that the following is included as part

of the installation:

 • Installgeneratoroutdoorsinanareathatwillnot

accumulate deadly exhaust gas.

 • DONOTinstallgeneratorwhereexhaustgascould

accumulate and enter inside or be drawn into a

potentially occupied building or structure.

 • BylawitisrequiredinmanystatestohaveaCarbon

Monoxide (CO) detector in operating condition in

homes and other structures occupied by people.

Carbon monoxide detector(s) (A) MUST be

installed and maintained indoors according to the

manufacturer’s instructions / recommendations.

A CO monitor is an electric device that detects

hazardous levels of CO. When there is a buildup of

CO, the monitor will alert the occupants by flashing

visual indicator light and alarm. Smoke alarms cannot

detect CO gas.

 • Nearbystructuresmaybeexposedtotheengine

exhaust from your standby generator and must be

considered when installing your standby generator.

 • Ensureexhaustgasiskeptawayfrom:

B overhead doors

C doors

D windows (not shown)

E other openings that can allow exhaust gas to enter

inside or be drawn into a potenially occupied building

or structure.

A

B

C

D

E

B BC

NOT

FOR REPRODUCTION

11

 • Directthestandbygeneratorexhaustawayfromor

parallel to the building or structure. DO NOT direct the

generator exhaust towards a potentially occupied

building, structure, windows, doors, ventilation

intakes, soffit vents, crawl spaces, open garage

doors or other openings where exhaust gas could

accumulate and enter inside or be drawn into a

potentially occupied building or structure.

 • DONOTplacestandbygeneratorinanyareawhere

leaves or debris normally accumulates. Position

standby generator in an area where winds will carry

the exhaust gas away from any potentially occupied

building or structure.

NOT

FOR REPRODUCTION

12

Placement of Standby Generator to REDUCE THE RISK OF FIRE

The National Fire Protection Association (NFPA) standard

NFPA 37 establishes criteria for minimizing the hazard

of fire during the installation and operation of stationary

combustion engines. NFPA 37 limits the spacing of an

enclosed generator from openings in walls, structures and

combustible materials outside the enclosure.

The placement requirements provided are based on

compliance to NFPA 37 2010 section 4.1.4.

WARNING Exhaust heat/gases could ignite combustibles or

structures resulting in death, serious injury and/or

property damage.

• Exhaust outlet side of weatherproof enclosure must have at least

5 ft (1.5 m) minimum clearance from any structure, shrubs, trees

or any kind of vegetation.

• Standby generator weatherproof enclosure must be at least

5 ft (1.5 m) from windows, doors, any wall opening, shrubs or

vegetation over 12 inches (30.5 cm) in height.

• Standby generator weatherproof enclosure must have a minimum

of 5 feet (1.5 m) overhead clearance from any structure, overhang

or trees.

• DO NOT place weatherproof enclosure under a deck or other type

of structure that may confine airflow.

• USE ONLY flexible steel fuel line provided. Connect provided fuel

line to generator, DO NOT use with or substitute any other flexible

fuel line.

• Smoke detector(s) MUST be installed and maintained indoors

according to the manufacturer’s instructions/ recommendations.

Carbon monoxide alarms cannot detect smoke.

• DO NOT place weatherproof enclosure in manner other than

shown in illustrations.

Examples of standby generator locations to reduce the

risk of fire:

Legend for Generator Locations to reduce the risk of fire.

A

Standby weatherproof enclosure must be at least 5 ft

(1.5 m) from windows, doors, any wall opening, shrubs

or vegetation over 12 inches (30.5 cm) in height.

B

Exhaust outlet side of weatherproof enclosure must

have at least 5 ft (1.5 m) minimum clearance from any

structure, shrubs, trees or any kind of vegetation.

C

Standby weatherproof enclosure must have a

minimum of 5 feet (1.5 m) overhead clearance from

any structure, overhang or trees.

NOTICE DO NOT place weatherproof enclosure under a deck

or other type of covered structure that may confine airflow.

Vertical Clearances

A

C

NOT

FOR REPRODUCTION

13

Legend for Generator Locations to reduce the risk of fire.

A

Standby weatherproof enclosure must be at least 5 ft

(1.5 m) from windows, doors, any wall opening, shrubs

or vegetation over 12 inches (30.5 cm) in height.

B

Exhaust outlet side of weatherproof enclosure must

have at least 5 ft (1.5 m) minimum clearance from any

structure, shrubs, trees or any kind of vegetation.

Typical Installations with Structure Without a Fire Rating

C

Standby weatherproof enclosure must have a

minimum of 5 feet (1.5 m) overhead clearance from

any structure, overhang or trees.

NOTICE DO NOT place weatherproof enclosure under a deck

or other type of covered structure that may confine airflow.

A

AA

A

5 ft (1.5 m) min.

Standby

5 ft (1.5 m) min.

5 ft (1.5 m) min. 5 ft (1.5 m) min.

Exhaust

A

5 ft (1.5 m) min.

Standby

5 ft (1.5 m) min.

Exhaust

B

NOT

FOR REPRODUCTION

14

Typical Installation with Single Structure Having a Fire Resistance Rating of at Least 1 Hour

Legend for Generator Locations to reduce the risk of

fire:

- Standby weatherproof enclosure must be at

least 5 ft. (1.5 m) from windows, doors, any wall

opening, shrubs, or vegetation over 12 inches

(30.5 cm) in height.

- Exhaust oulet side of weatherproof enclosure

must have at least 5 ft. (1.5 m) minimum

clearance from any structure, overhang or trees.

- Standby weatherproof enclosure must have a

minimum of 5 ft. (1.5 m) overhead clearance from

any structure, overhang, or trees.

NOTICE DO NOT place weatherproof enclosure under

a deck or other type of coverend structure that may

confine airflow.

5 ft (1.5 m) min.

Standby

5 ft (1.5 m) min.

Standby

A

B

3 ft (0.9 m) min.

2 ft (0.6 m) min.

Exhaust

B

Exhaust

B

A

B

C

NOT

FOR REPRODUCTION

15

Typical Installation with Dual Structure Having a Fire Resistance Rating of at Least 1 Hour

Legend for Generator Locations to reduce the risk of

fire:

- Standby weatherproof enclosure must be at

least 5 ft. (1.5 m) from windows, doors, any wall

opening, shrubs, or vegetation over 12 inches

(30.5 cm) in height.

- Exhaust oulet side of weatherproof enclosure

must have at least 5 ft. (1.5 m) minimum clearance

from any structure, overhang or trees.

- Standby weatherproof enclosure must have a

minimum of 5 ft. (1.5 m) overhead clearance from

any structure, overhang, or trees.

NOTICE DO NOT place weatherproof enclosure under

a deck or other type of coverend structure that may

confine airflow.

5 ft (1.5 m) min.

Standby

A

3 ft (0.9 m) min.

2 ft (0.6 m) min.

B

Exhaust

B

Exhaust

A

B

C

NOT

FOR REPRODUCTION

16

Other General Location Guidelines

 • Placethestandbygeneratorinapreparedlocation

that is flat and has provisions for water drainage.

 • Installthestandbygeneratorinalocationwhere

sump pump discharge, rain gutter down spouts, roof

run-off, landscape irrigation, or water sprinklers will

not flood the unit or spray the enclosure and enter

any air inlet or outlet openings.

 • Installthestandbygeneratorwhereitwillnotaffector

obstruct any services (including covered, concealed

and underground), such as telephone, electric, fuel

(natural gas / LPG vapor), irrigation, air conditioning,

cable, septic, sewer, well and so forth.

 • Installthestandbygeneratorwhereleaves,grass,

snow, etc will not obstruct air inlet and outlet

openings. If prevailing winds will cause blowing or

drifting, you may need to construct a windbreak to

protect the unit.

NOT

FOR REPRODUCTION

17

Concrete Slab

At the appropriate location, construct a concrete slab:

 • 28daycompressionstrengthof3000psi(200MPa)

 • Minimum5”(13cm)thick

 • Minimum6”(15cm)widerthanenclosureonallsides

(shown as D in figure)

 • StrengthenslabwithNo.6reinforcingbars(on

12”(30.5cm)centers)or8ga.steelwirefabric(6”

(15cm) centers).

Avoid placing reinforcement in entrance stub-up area (shown

as (B ).

Attach unit to slab at four corner locations (A) with minimum

5/16”diameter(8mm)masonryanchorboltslongenoughto

secure the unit.

The fuel inlet location (C) ,the concrete slab, and the

exhaust outlet (E) are shown for reference.

34-1/4”

87cm

14-3/4”

37.5cm

92”

233.7cm

51”

129.5cm

6”

15.2cm

5”

12.7cm

7-1/2”

19cm

C

D

A

B

Electrical and Fuel Inlet Locations

A through-slab power cable stub-up is preferred (see

figure above). If stub-up’s are not used, (F) indicates the

recommended location for punching holes for attaching

power conduit. The 1 inch N.P.T. fuel inlet connector (C) is

shown for reference.

C

A Holes located in base to anchor to pad

B Stub up Area

C Fuel Inlet

D Concrete slab

D Exhaust Outlet

B

C

D

A

D

C

B

A

F

C

F

E

NOT

FOR REPRODUCTION

18

Remove circuit breaker box bottom plate prior to positioning

generator.Two60”lengthsof2”Schedule40pipe(A ,

supplied by the installer, are required to lift the generator

onto cement pad. Insert pipes through the lifting holes (B)

located near the unit’s base.

Use a spreader bar to ensure that the chains, straps or

cables DO NOT touch the generator’s roof. Retouch any

chipped paint with supplied touch-up paint.

Lifting the Generator

The generator weighs more than 1,700 pounds (771 kg).

Proper tools, equipment and qualified personnel should be

used in all phases of handling and moving the generator.

A B

WARNING Hazardous Voltage - Contact with power lines could

cause electric shock or burn, resulting in death or

serious injury.

Lifting Hazard / Heavy Object - Could result in

serious injury.

• If lifting or hoisting equipment is used, DO NOT contact any

power lines.

• DO NOT lift or move generator without assistance.

• Use lifting pipes as described in Lifting the Generator.

• DO NOT lift unit by roof as damage to generator will occur.

A

B

NOT

FOR REPRODUCTION

19

The generator is equipped with an enclosure that has

several access doors, as shown. The doors are named for a

significant component located behind them, as follows:

A - Fuel Inlet port (shown for reference)

B - Control Panel door (may be one door)

C - Exhaust opening (shown for reference)

D - Coolant/Oil Fill door

E - Battery door

F - Muffler door

The Coolant Fill, Battery and Control Panel doors must be

installed whenever the unit is running to assure proper

cooling, reduce noise and for added safety. The enclosure

also includes muffler and radiator access panels, used for

cleaning those components. Those panels should remain

closed at all other times.

Access Ports

Each generator is shipped with a set of identical keys. These

keys fit the locks that secure the access ports.

To open access door:

1. Insert key into lock of access door handle and turn

key one quarter turn counterclockwise.

2. Grasp door’s handle and turn one quarter turn

counterclockwise to open. Remove key.

3. Coolant Fill door is unlocked in the same manner. It

can be used for adding coolant or oil.

To close access door:

1. Close door and turn door’s handle one quarter

turn clockwise.

2. Insert key into lock of door handle and turn key one

quarter turn clockwise. Remove key.

Additional force may be required to fully close and lock

the doors because they create a pressurized seal for the

generator enclosure.

WARNING Contact with muffler area could cause burns

resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

C

E

D

A

B

F

A

B

C

D

E

F

NOT

FOR REPRODUCTION

20

 • Aminimumofoneaccessible,approvedmanual

shutoff valve (F) shall be installed in the fuel supply

line within 6 ft (1.8 m) of the generator.

 • Amanualfuelshut-offvalvelocatedintheinteriorof

the building.

 • Wherelocalconditionsincludeearthquake,

tornado, unstable ground, or flood hazards, special

consideration shall be given to increase strength and

flexibility of piping supports and connections.

 • Pipingmustbeofthecorrectsizetomaintainthe

required supply pressures and volume flow under

varying generator load conditions with all gas

appliances connected to the fuel system turned on

and operating.

 • Useapipesealantorjointcompoundapprovedfor

use with NG/LPG on all threaded fittings to reduce the

possibility of leakage.

 • Installedpipingmustbeproperlypurgedand

leak tested, in accordance with applicable codes

and standards.

The information below is provided to assist gaseous fuel

system technicians in planning installations. In no way

should this information be interpreted to conflict with

applicable fuel gas codes. Consult with your local fuel

supplier or Fire Marshall if questions or problems arise.

TO THE INSTALLER: Consult with the generator owner(s) and

convey any technical considerations that might affect their

installation plans before applying these general guidelines.

The following general rules apply to gaseous fuel

system piping:

 • Thepipingshouldbeofamaterialthatconforms

to federal and local codes, rigidly mounted and

protected against vibration.

 • Pipingshouldbeprotectedfromphysicaldamage

where it passes through flower beds, shrub beds, and

other cultivated areas where damage could occur.

 • Installtheflexible,gaseoushose(B)(supplied)

between the generator Fuel Inlet port and rigid

piping to prevent thermal expansion or contraction

from causing excessive stress on the piping material.

 • Aunion(C)orflangedconnectionshallbeprovided

downstream from this valve to permit removal

of controls.

 • Amanometerportshouldbeprovided(D).Adigital

manometer, P/N 19495, is available at your Briggs &

Stratton service center. When the initial test runs are

complete, the manometer is removed and the port

is plugged. The manometer port permits temporary

installation of a manometer to ensure that the

engine receives the correct fuel pressure to operate

efficiently throughout its operating range.

 • Wheretheformationofhydratesoriceisknownto

occur, piping should be protected against freezing.

The termination of hard piping should include a

sediment trap (E) where condensate is not likely

to freeze.

The Gaseous Fuel System

WARNING Propane and Natural Gas are extremely flammable

and explosive, which could cause burns, fire or

explosion resulting in death, serious injury and/or

property damage.

• LP gas is heavier than air and will settle in low areas.

• Natural gas is lighter than air and will collect in high areas.

• The slightest spark could ignite these fuels and cause an explosion.

• DO NOT light a cigarette or smoke.

NOTICE The supplied flexible gaseous pipe is not to be installed

underground or in contact with the ground.

• The entire flexible gaseous pipe must be visible for periodic

inspection and must not be concealed within nor contact nor run

through any wall, floor, or partition.

A

B

C

D

E

F

A Generator Fuel Inlet

B Flexible Fuel Hose

C Union Fitting

D Manometer Test Port

E Sediment Trap

F Manual Shut-off Valve

A

B

C

D

E

F

B

C

D

E

F

A

NOT

FOR REPRODUCTION

La page est en cours de chargement...

Simplicity 076052-00 Guide d'installation

Ce manuel convient également à

Simplicity 076052-00 Guide d'installation

dans d''autres langues

Autres documents