Bosch HBN5450UC/08 Guide d'installation

Marque: Bosch

Modèle: HBN5450UC/08

Catégorie: Micro-ondes

Taper: Guide d'installation

installation Manual

Guide d'installation

Manual de instalaci6n

Built-in Ovens

Models: HBL33, HBL34, HBN34, HBL35, HBN35, HBL54, HBN54,

HBL56, HBN56, HBL57, HBL8450, HBL8650, HBL8750

,,lllllllllllllllh_

_,,_ ,, ,

,,,,,,,,,,,,,,,,,,

....._,_f;'

' ,,,u

_' illlllllllllllllllll,i.... _

,,,,,,,,,,,,,,,,,,.....

,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,

Table of Contents

Safety ....................................................... 1

Important Safety Instructions ..................................... 1

Preparation .................................................. 2

Before you Begin ............................................... 2

Tools and Parts Needed ...................................................... 2

Parts Included .............................................................. 2

General Information .......................................................... 2

Dimensions for 27" Wall-Mounted Units ............................. 3

Dimensions for 27" under the counter ............................................ 4

Dimensions for 30" Wall-Mounted Units ............................. 5

Dimensions for 30" under the counter ............................................ 7

Removing Packaging ............................................ 7

For Convection Microwave Combination Units ..................................... 7

Preparing Oven ............................................................. 8

Microwave Combination Units Adjustment Feature .................................. 9

Installation ................................................. 10

Electrical Installation ........................................... 10

Oven Installation ............................................... 11

Testing Operation .............................................. 11

Service ..................................................... 12

Before Calling Service ....................................................... 12

This Bosch Appliance is made by BSH

Home Appliances Corporation

1901 Main Street, Suite 600

Irvine, CA 92614

Questions?

1-800-944-2904

www.boschappliances.com

We look forward to hearing from you!

Safety

Important Safety

Instructions

READ AND SAVE THESE

INSTRUCTIONS

WARNING:

If the information in this manual is not followed exactly, fire

or shock may result causing property damage or personal

injury.

WARNING:

Do not repair or replace any part of the appliance unless

specifically recommended in the manuals. Improper

installation, service or maintenance can cause injury or

property damage. Refer to this manual for guidance. All

other servicing should be done by a qualified technician.

Appliance Handling Safety

Do not lift appliance by door handle. Remove the door for

easier handling and installation. See instructions in Use

and Care Manual.

Unit is heavy and requires at least two people or proper

equipment to move.

Hidden surfaces may have sharp edges. Use caution when

reaching behind or under appliance.

Safety Codes and Standards

This appliance complies with one or more of the following

Standards:

• UL 858, The Standard for the Safety of Household

Electric Ranges

• UL 923, The Standard for the Safety of Microwave

Cooking Appliances

• UL 507, The Standard for the Safety of Electric Fans

ANSI Z21.1, The American National Standard for

Household Cooking Gas Appliances

CAN/CSA-C22.2 No. 113-M1984 Fans and Ventilators

CAN/CSA-C22.2 No. 61-M89 Household Cooking

Ranges

It is the responsibility of the owner and the installer to

determine if additional requirements and/or standards

apply to specific installations.

Electric Safety

Before you plug in an electrical cord, be sure all controls

are in the OFF position.

If required by the National Electrical Code (or Canadian

Electrical Code), this appliance must be installed on a

separate branch circuit.

Installer - show the owner the location of the circuit

breaker or fuse. Mark it for easy reference.

Important - Save these instructions for the local electrical

inspector's use.

Before installing, turn power OFF at the service panel. Lock

service panel to prevent power from being turned ON

accidentally.

Refer to data plate for more information. See "Data Plate"

under "Service" for data plate location.

Be sure your appliance is properly installed and grounded

by a qualified technician. Installation, electrical connections

and grounding must comply with all applicable codes.

Related Equipment Safety

Remove all tape and packaging before using the appliance.

Destroy the packaging after unpacking the appliance.

Never allow children to play with packaging material.

Never modify or alter the construction of the appliance. For

example, do not remove leveling legs, panels, wire covers

or anti-tip brackets/screws.

English 1

Transport

To avoid damage to the oven vent, use the transport

method shown in the picture below.

Preparation

Before you Begin

Tools and Parts Needed

• Phillips head screwdriver

• Measuring tape

• Drill with bit (1/8")

Parts Included

• Phillips head screws (6)

General Information

Power Requirements

The outlet must be properly grounded in accordance with

all applicable codes.

English 2

Dimensions for 27"

Wall-Mounted Units

Single Oven 27"

24"

(610ram)

251/2"

24t3/16"

23W8" (606mm)

(718mm)

J 22" (559mm)

It is good practice, when oven is installed at the end of a

cabinet run, adjacent to a perpendicular wall or cabinet

door, to allow at least 114" space between the side of the

oven and the wall/door.

For oven support, install 2x4's extending front to back flush

with the bottom and the side of the opening. The supporting

base must be well secured to the floor/cabinet and level.

Note:

The conduit box must be installed either above or below the

unit. If the conduit box is installed below the unit, a 2"

diameter hole or space is required between the back wall

and the right rear of the 2x4 supports.

The cabinet base must be flat and capable of supporting a

weight of at least 193 Ibs (87 kg).

Double Oven 27"

251/2"

513f4"

(131 imm)

It is good practice, when oven is installed at the end of a

cabinet run, adjacent to a perpendicular wall or cabinet

door, to allow at least 114"space between the side of the

oven and the wall/door.

For oven support, install 2x4's extending front to back flush

with the bottom and the side of the opening. The supporting

base must be well secured to the floor/cabinet and level.

Note:

The conduit box must be located above the unit to facilitate

connecting and servicing.

The cabinet base must be flat and capable of supporting a

weight of at least 361 Ibs (164 kg).

English 3

Combo Oven with Microwave and

Warming Drawer 27"

6 1 318"

(1559mm)

595/8"

(1514turn)

mino 43N"

max, 12318"(315mm)

It is good practice, when oven is installed at the end of a

cabinet run, adjacent to a perpendicular wall or cabinet

door, to allow at least 114" space between the side of the

oven and the wall/door.

For oven support, install 2x4's extending front to back flush

with the bottom and the side of the opening. The supporting

base must be well secured to the floor/cabinet and level.

The cabinet base must be flat and capable of supporting a

weight of at least 369 Ibs (167 kg).

27" Under-the-counter units

24"

(610ram)

43/4"

(121mm)

It is good practice, when oven is installed at the end of a

cabinet run, adjacent to a perpendicular wall or cabinet

door, to allow at least 114"space between the side of the

oven and the wall/door.

For oven support, install 2x4's extending front to back flush

with the bottom and the side of the opening. The supporting

base must be well secured to the floor/cabinet and level.

The cabinet base must be flat and capable of supporting a

weight of at least 193 Ibs (87 kg).

English 4

Dimensions for 30"

Wall-Mounted Units

Single Oven 30"

281/2"

It is good practice, when oven is installed at the end of a

cabinet run, adjacent to a perpendicular wall or cabinet

door, to allow at least 114" space between the side of the

oven and the wall/door.

For oven support, install 2x4's extending front to back flush

with the bottom and the side of the opening. The supporting

base must be well secured to the floor/cabinet and level.

Note:

The conduit box must be installed either above or below the

unit. If the conduit box is installed below the unit, a 2"

diameter hole or space is required between the back wall

and the right rear of the 2x4 supports.

The cabinet base must be flat and capable of supporting a

weight of at least 212 Ibs (96 kg).

Double Oven 30"

2713/16"

(706ram)

28112"

It is good practice, when oven is installed at the end of a

cabinet run, adjacent to a perpendicular wall or cabinet

door, to allow at least 114"space between the side of the

oven and the wall/door.

For oven support, install 2x4's extending front to back flush

with the bottom and the side of the opening. The supporting

base must be well secured to the floor/cabinet and level.

Note:

The conduit box must be located above the unit to facilitate

connecting and servicing.

The cabinet base must be flat and capable of supporting a

weight of at least 390 Ibs (177 kg).

English 5

Combo Oven with Microwave 30"

(1270mm)

It is good practice, when oven is installed at the end of a

cabinet run, adjacent to a perpendicular wall or cabinet

door, to allow at least 114" space between the side of the

oven and the wall/door.

For oven support, install 2x4's extending front to back flush

with the bottom and the side of the opening. The supporting

base must be well secured to the floor/cabinet and level.

Note:

The conduit box must be located above the unit to facilitate

connecting and servicing.

The cabinet base must be flat and capable of supporting a

weight of at least 310 Ibs (141 kg).

Combo Oven with Microwave and

Warming Drawer 30"

It is good practice, when oven is installed at the end of a

cabinet run, adjacent to a perpendicular wall or cabinet

door, to allow at least 114"space between the side of the

oven and the wall/door.

For oven support, install 2x4's extending front to back flush

with the bottom and the side of the opening. The supporting

base must be well secured to the floor/cabinet and level.

Note:

The conduit box must be located above the unit to facilitate

connecting and servicing.

The cabinet base must be flat and capable of supporting a

weight of at least 429 Ibs (195 kg).

English 6

Dimensions for 30" Under-the-counter

Units

Removing Packaging

• Cut straps on outside of box.

• Remove cardboard box.

• Remove all top and side cardboard and Styrofoam

braces.

• Place oven in front of cabinets where it is to be

installed.

• Unscrew unit from Left and Right Brackets as show in

"Left and Right Packaging Bracket Removal."

Left Packaging Bracket Removal

It is good practice, when oven is installed at the end of a

cabinet run, adjacent to a perpendicular wall or cabinet

door, to allow at least 114" space between the side of the

oven and the wall/door.

For oven support, install 2x4's extending front to back flush

with the bottom and the side of the opening. The supporting

base must be well secured to the floor/cabinet and level.

The cabinet base must be flat and capable of supporting a

weight of at least 212 Ibs (96 kg).

Right Packaging Bracket Removal

Note:

Different models use different packaging materials. Actual

brackets may look differently. Bracket remains in packaging

base. Unit should stay on packaging base until ready to be

lifted into cabinet cutout.

English 7

For Convection Microwave Combination Units

(for Convection Microwave Combination Units Only)

Preparing Oven

Place oven in front of cabinets where it is to be installed.

Rest it on a jack or other sturdy support so that it is in line

with the cabinet cutout.

Remove Convection Microwave Shipping Bracket Screw

prior to installation.

English 8

Microwave Combination Units

Adjustment Feature

Remove Convection Microwave Shipping Bracket screw

prior to installation as shown in "Convection Microwave

Shipping Bracket Screw Removal."

Note: To adjust the fit between the microwave frame and

kitchen cabinet, refer to the following diagrams and

charts.

Note: Fixed position screws may be moved to adjustable

slots when necessary.

This illustration shows models with convection microwave.

Your model may vary.

Adjustment Description Number of

Screws

A Frame Up and 4

Down

B Frame Back and 8

Forward

English 9

..................................................................................................................................................................................................................................................................................................._iii_iii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_!ii_ _iiiiii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_ii!_iiiiii__i_

Installation

Electrical Installation

All model ovens on the front cover are dual rated, designed

to be connected to either 208/240V AC, 60 Hz, 4 wire,

single-phase power supply.

Model Circuit Required

208V, 60 Hz 240V, 60 Hz

HBL33, HBN34, 25 AMP 30 AMP

HBL34

HBN54, HBL54

30 AMP

HBL84

HBN35, HBL35 40 AMP

HBN56, HBL56, 30 AMP 40 AMP

HBL8650,

HBL57, 50 AMP

HBL8750

The electrical supply should be a 4-wire single-phase AC.

Install a suitable conduit box (not furnished). An

appropriately-sized, UL-listed conduit connector must be

used to correctly attach the conduit to the junction box.

Important: Local Codes may vary; installation, electrical

connections and grounding must comply with all applicable

local codes.

If local codes permit grounding through the electrical

supply neutral, connect both the white neutral wire and the

bare ground wire from the oven to the white neutral

electrical supply wire.

Electrical Connection

The four-wire connection is preferred, but where local

codes permit, the three wire connection is also acceptable.

Four-wire Connection

Junction box.\ Cable from

\\ power supply

Red wires

White wires

Ungrounded Neutral

"""-..\ Black wires

Bare or green wires Cable

from oven "\ U.L.-listed conduit connector

• Connect the red oven wire to the red electrical supply

wire (hot wire).

• Connect the black oven wire to the black electrical

supply wire (hot wire).

• Connect the white neutral oven wire to the white

neutral (not bare ground) electrical supply wire.

• Connect the bare ground oven wire to the bare ground

electrical supply wire.

Three-wire Connection

Juncti°n b°x _eer f_°pmply

Whitewires Redwires_ _ _ Grounded Neutral

from oven

• Connect red wire from oven to red wire in junction box.

• Connect black wire from oven to black wire in junction

box.

• Connect both green ground wire and white wire from

oven to white (or gray) neutral wire in junction box.

The conduit cable, where connected at the oven, swivels.

Rotate conduit cable upward (or downward) and direct

through hole prepared in cabinet to attach to J-Box.

To maintain serviceability, the flex conduit must not be

shortened and should be routed to permit temporary

removal of the oven.

English 10

Oven Installation

Note:

Before installing the oven, be sure to verify the cabinet

dimensions and electrical connections.

Removing the Oven Door

For ease of installation, some oven doors may be removed

to reduce the weight of the oven by 30 Ibs (14 kg) per door,

before installing into the cabinet. See instructions below.

,_ CAUTION:

When removing the door:

Make sure oven is cool and power to the

oven has been turned off before

removing the door. Failure to do so could

result in burns.

• The oven door is heavy and fragile. Use

both hands to remove the oven door. The

door front is glass. Handle carefully to

avoid breaking.

• Grasp only the sides of the oven door. Do

not grasp the handle as it may swing in

your hand and cause damage or injury.

• Failure to grasp the oven door firmly and

properly could result in personal injury or

product damage.

• To avoid injury from hinge bracket

snapping closed, be sure that both levers

are securely in place before removing the

door. Also, do not force door open or

closed - the hinge could be damaged and

injury could result.

• Do not lay removed door on sharp or

pointed objects as this could break the

glass. Lay on a flat, smooth surface,

positioned so that the door cannot fall

over.

To remove the oven door:

, Be sure to read the

above CAUTION

before attempting to

remove the door.

2. Open the door

completely.

3. Flip levers on hinges

toward you.

4. Holding the door firmly

on both sides and

using both hands,

close the door gently

until it stops against

the levers, about 30°

from the closed

position.

5. Carefully lift the door

up and out of the

hinge slots. Hold

firmly; the door is

heavy.

6. Place the door in a

convenient and stable

location for cleaning.

Installing the Oven

1. Liftor slide unit into cabinet cutout. Do not lift appliance

by door handle.

2. Push straight in until oven trim is flush with cabinet

wall, being careful not to crimp flexible conduit between

oven and cabinet back wall. The oven should be

straight and level, not crooked.

3. Install supplied screws through tap holes in trim. (2

screws for single ovens, 4 screws for double/combo

ovens)

English 11

To replace the oven door:

Hold the door firmly in

both hands.

Hold the door at a 30°

angle from the closed

position and insert

hinges into the slots.

You may need to rock

the door forward and

backward slightly to

seat the hinge feet.

The door may need to

be removed and re-

inserted until the

hinges sit correctly in

the slots.

4. Open door all the way

to expose hinges,

levers, and slots.

5. Push levers forward

and down until seated

on the bracket.

Close and open door

slowly to be sure it is

correctly and securely

in place. Door must be

straight, not crooked.

Testing Operation

1. Turn on power at the breaker.

2. Test the oven mode.

Select the BAKE mode. See the Use and Care Manual

for detailed operation instructions.

3. Verify that the oven light comes on and the oven begins

to preheat.

4. Test the door lock.

Set the SELF CLEAN mode. Confirm that the door

locks when the lock icon appears in the display.

5. If installing a double oven, test the second oven as

well.

6. If any of the tests do not result as explained above,

contact Bosch service for assistance. Otherwise, the

installation is complete at this time.

Service

Before Calling Service

See Use and Care Manual for troubleshooting information.

Refer to the Warranty in the Use and Care Manual.

To reach a service representative, see the contact

information at the front of the manual. Please be prepared

with the information printed on your product data plate

when calling.

Data Plate

The data plate shows the model and serial number. Refer

to the data plate on the appliance when requesting service.

The data plate is located on the underside of the control

panel:

English 12

English13

Table des mati res

Sdcuritd ..................................... 1

Consignes de securit6 importantes ................................... 1

Prdparation .................................. 3

Avant de commencer ............................................. 3

Outils et pieces necessaires ................................................... 3

Pieces incluses ............................................................. 3

Appareils electrom6nagers de 27 po ................................. 3

Informations generales ....................................................... 3

Appareils electrom6nagers de 30 po ................................. 6

Pourenlever I'emballage ........................................... 9

Caracteristique d'adjustement pour combine micro-ondes a convection ........... 9

Installation ................................. 11

Installation electrique ............................................ 12

Raccordement electrique ..................................................... 12

Installation du four ............................................... 13

Test de contr61e ................................................ 14

Ddpannage ................................. 15

Avant d'appeler le service de depannage ........................................ 15

Cet appareil 61ectromenager de Bosch est fait par

BSH Home Appliances Ltd.

6696 Financial Drive, Unit 3

Mississauga, ON L5N 7J6

Questions ?

1-800-944-2904

www. bosch-home.ca

Nous attendons de vos nouvelles !

S6curitd

Consignes de

sdcuritd

importantes

LIRE ET CONSERVER CES

CONSIGNES

AVERTISSEMENT:

si les informations de ce manuel ne sont pas suivies _ la

lettre, un incendie ou un choc 61ectrique peuvent se

produire et sont susceptibles de causer des dommages

mat@iels ou des 16sions corporelles.

AVERTISSEMENT:

ne pas r6parer ni remplacer des pi_ces de I'appareil

moins que cela ne soit express6ment recommand6 dans le

manuel. Toute installation, r6paration ou maintenance

inad6quate peut entrafner des blessures ou des

dommages mat@iels. Consulter ce manuel pour obtenir

des conseils sur la fagon de proc6der. Tousles travaux

d'entretien doivent 6tre confi6s _ un technicien qualifi6.

Securite de manipulation de rappareil

Ne pas soulever I'appareil par la poign6e de la porte.

Enlever la porte pour faciliter la manipulation et I'installation

de I'appareil. Voir les instructions du Manuel d'utilisation et

d'entretien.

Cet appareil est Iourd et il faut au moins deux personnes ou

1'6quipement appropri6 pour le d6placer.

Les surfaces cach6es peuvent comporter des ar_tes vives.

Faites attention en 6tendant le bras derri@e I'appareil ou

en dessous.

Codes et normes de securite

Cet appareil est conforme _ une ou plusieurs des normes

suivantes :

• UL 858, Norme pour la s6curit6 des cuisini_res

61ectriques domestiques

• UL 923, Norme pour la s6curit6 des appareils de

cuisson _ micro-ondes

• UL 507, Norme pour la s6curit6 des ventilateurs

61ectriques

• ANSI Z21.1, Norme nationale am6ricaine pour les

appareils de cuisson _ gaz domestiques

CAN/CSA-C22.2 No. 113-M 1984, Ventilateurs et

soufflantes

CAN/CSA-C22.2 No. 61-M89, Cuisini@es pour usage

m6nager

II incombe au propri6taire et _ I'installateur de d6terminer si

des exigences et/ou normes additionnelles s'appliquent

pour des installations sp6cifiques.

Securite electrique

Avant de brancher le cordon 61ectrique, v@ifier que toutes

les commandes sont dans la position "OFF" (Arr6t).

S'il y a lieu, conform6ment au Code national de 1'61ectricit6

(ou au Code canadien de 1'61ectricit6),cet appareil doit 6tre

install6 sur un circuit de d@ivation s6par6.

Installateur - indiquer au propri6taire I'emplacement du

disjoncteur ou du fusible. Identifier sa position pour pouvoir

le retrouver facilement plus tard.

Important - Conserver ces instructions pour I'usage de

I'inspecteur local en 61ectricit6.

Avant I'installation, couper le courant au panneau de

service. Verrouiller le panneau de service pour 6viter que le

courant ne soit accidentellement r6tabli.

Pour plus d'informations, se reporter _ la plaque

signal6tique. Pour connaftre I'emplacement de la plaque

signal6tique, voir "Plaque signal6tique" sous "Entretien".

S'assurer que I'appareil est ad6quatement install6 et mis

la terre par un technicien qualifi6. L'installation, les

connexions 61ectriques et la mise _ la terre doivent 6tre

conformes _ tousles codes applicables.

Securite apparentee concernant I'equipement

Retirer le ruban adh6sif et I'emballage avant d'utiliser

I'appareil. D6truire I'emballage apr_s avoir d6ball6

Frangais 1

I'appareil.Nejamaislaisserlesenfantsjoueravecles

mat@iauxdeconditionnement.

Nejamaismodifiernialt@erlaconfigurationdeI'appareil.

Parexemple,nepasretirerlespiedsdenivellement,les

panneaux,lescouverclesdec_blageoulesfixations/vis

antibasculement.

Transport

Pour 6viter tout dommage _ 1'6vent du four, utiliser la

m6thode de transport illustr6e ci-dessous.

Frangais 2

Prdparation

Avant de commencer

Outils et pieces necessaires

• Toumevis _ t_te Phillips

• Ruban _ mesurer

• Perceuse avec foret (1/8 po)

Pieces incluses

• Vis cruciformes (6)

Informations gen6rales

Exigences electriques

• La prise doit _tre correctement reli6e _ la terre selon

tous les codes applicables.

Fran9ais 3

Appareils dlectromdnagers

de 27 po

La prise doit _tre correctement reli6e _ la terre selon tous

les codes applicables.

Four unique de 27 po

Fours doubles de 27 po

Lorsque le four est install6 _ I'extr6mit6 d'une s6rie de

placards, adjacent _ un mur perpendiculaire ou _ une porte

de placard, il est recommand6 de laisser au moins 1/4 po

(0,6 cm) d'espace entre la paroi du four et lemur ou la

porte.

Pour le soutien du four, installer des montants de 2 pouces

sur 4 qui s'6tendent de I'avant _ I'arri_re et viennent

affleurer le fond et le c6t6 de I'ouverture. Le socle de

soutien doit 6tre bien fix6 au plancher ou au coffret et 6tre

de niveau.

Remarque : la boTte de connexions doit _tre install6e soit

au-dessus, soit au-dessous de I'appareil. Si la boTte de

connexions est install6e sous I'appareil, un espace ou une

ouverture de 2 po (5,8 cm) de diam_tre est requis entre le

mur arri_re et la partie arri_re droite des montants de

support de 2 pouces sur 4.

Le socle du coffret doit _tre plate et apte _ soutenir un

poids d'au moins 193 Ib (87 kg).

51314"

(!31imm)

Lorsque le four est install6 _ I'extr6mit6 d'une s6rie de

placards, adjacent _ un mur perpendiculaire ou _ une porte

de placard, il est recommand6 de laisser au moins 1/4 po

(0,6 cm) d'espace entre la paroi du four et lemur ou la

porte.

Pour le soutien du four, installer des montants de 2 pouces

sur 4 qui s'6tendent de I'avant _ I'arri_re et viennent

affleurer le fond et le c6t6 de I'ouverture. Le socle de

soutien doit 6tre bien fix6 au plancher ou au coffret et 6tre

de niveau.

Remarque : la bofte de connexions doit 6tre situ6e au-

dessus de I'appareil pour faciliter les branchements et

I'entretien.

Le socle du coffret doit _tre plate et apte _ soutenir un

poids d'au moins 361 Ib (164 kg).

Frangais 4

La page charge ...

Bosch HBN5450UC/08 Guide d'installation

Marque: Bosch

Modèle: HBN5450UC/08

Catégorie: Micro-ondes

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Bosch HBN5450UC/08 Installation guide
español: Bosch HBN5450UC/08 Guía de instalación

Bosch HBN5450UC/08 Guide d'installation

Bosch HBN5450UC/08 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents