Magic Chef CDB7000AWB4 Guide d'installation

Marque: Magic Chef

Modèle: CDB7000AWB4

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Ce manuel convient également à

INSTALLATIONINSTRUCTIONS

UNDERCOUNTERDISHWASHER

PLASTICGIANT TUBMODELS

INSTRUCTIONSD'INSTALLATION

LAVE-VAISSELLESOUSCOMPTOIR

MODELESA TRESGRANDE CUVE EN PLASTIQUE

Table of Contents .............................................................. 2

Table des matieres .......................................................... 21

W10329310A

TABLEOF CONTENTS

DISHWASHER SAFETY ............................................................................... 2

INSTALLATION REQUIREMENTS ............................................................. 3

Tools and Parts ......................................................................................... 3

Location Requirements ............................................................................. 3

Drain Requirements .................................................................................. 5

Water Supply Requirements ..................................................................... 5

Electrical Requirements ............................................................................ 5

INSTALLATION INSTRUCTIONS ............................................................... 6

Prepare Cabinet Opening--Existing Utilities ............................................ 6

Prepare Cabinet Opening-- New Utilities ................................................. 6

Prepare and Route Water Line ................................................................. 7

Install Drain Hose ...................................................................................... 8

Prepare Dishwasher ................................................................................ 10

INSTALLATION INSTRUCTIONS (CONT.)

Make Power Supply Cord Connection .................................................. 11

Determine Cabinet Opening ................................................................... 13

Choose Attachment Option .................................................................... 13

Move Dishwasher Close to Cabinet Opening ........................................ 14

Connect to Water Supply ....................................................................... 16

Connect to Drain ..................................................................................... 16

Make Direct Wire Electrical Connection ................................................. 17

Secure Dishwasher in Cabinet Opening ................................................ 18

Complete Installation .............................................................................. 19

Check Operation ..................................................................................... 20

If Dishwasher Does Not Operate ............................................................ 20

Additional Tips ........................................................................................ 20

DISHWASHERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

You Need to:

• Slowly open dishwasher door while someone grasps the rear

of the dishwasher. Remove shipping materials, drain hose and

lower rack. Close dishwasher door until latched.

• Observe all governing codes and ordinances.

• Install this dishwasher as specified in these instructions.

• Installation should be performed by a qualified service

technician. The dishwasher must be installed to meet all

electrical and plumbing national and local codes and

ordinances.

INSTALLATION

REQUIREMENTS

Gather the recommended tools and parts before starting

installation. Read and follow the instructions 3rovided with any

tools listed here.

All Installations

Toolsneeded:

%0"and I/4"

nut drivers or

heX soCkets

Measuring tape

or ruler

10" adjustable wrenc

that opens to

11/8,!(2,9 cm)

UL LiSted/CSA _

APPrOVed twist-on U

wire connectors*

*Must be the proper size to connect your household wiring to

16-gauge wiring in dishwasher.

Other useful items you may need:

Parts supplied:

Silver Green

Make sure all these parts are included in the literature package.

Parts needed:

%" compr ×¾, hose fitting

For part or kit, see local

retailer or call Whirlp0ol

Parts! 1,800-442-9991, Part

Number W10273460

Other parts you may also need:

1'/2" " Sidem0unting kit

--2

(38:!_ 5 cm) for solid surface Idu_

_Screw:type I c0untertops I

[clamPs(3 maximum)J (Part Number I8212560) J

NOTE: Parts available for purchase in plumbing supply stores.

Check local codes. Check existing electrical supply. See

"Electrical Requirements" section. It is recommended that

electrical connections be made by a licensed electrical installer.

In addition, for first-time installations

Tools needed:

with 1/2i[3/4_ Y/_ ] _

and 11/2 hole _/_ ] Sma

sawbks _ ] tubing cutter wire stripper

Parts needed:

CopPer tubing (3/_'! See "Electrical Requirements,, secti0nl

O.D Suggested)or

flexibebadedlr i For Direct Wire'., For Power Supply

water suna v ne use UL Dsted/ Cord: use UL

CSA Approved Listed/CSA

I strain App[oved power

tttt,tt. Ito fit % (2,2 €m) supply cord kit

hole marked for use with

dishwasher

Grounded electrical supply required.

Do not run drain lines, water lines or electrical wiring where they

can interfere with or contact dishwasher motor or legs.

The location where the dishwasher will be installed must provide

clearance between motor and flooring. Motor should not touch

the floor.

Do not install dishwasher over carpeted flooring.

Shelter dishwasher and water lines leading to dishwasher against

freezing. Damage from freezing is not covered by the warranty.

A side panel kit is available from your dealer for installing your

dishwasher at the end of your cabinetry.

A moisture barrier accessory (Part Number 4396277) is available

from your dealer for installing underneath the countertop.

Check location where dishwasher will be installed. The location

must provide:

• easy access to water, electricity and drain.

convenient access for loading and unloading dishes.

Corner locations require a 2" (5.1 cm) minimum clearance

between the side of the dishwasher door and the wall or

cabinet.

• square opening for proper operation and appearance.

• cabinet front perpendicular to floor.

• level floor. (If floor at front of opening is not level with floor

at rear of opening, shims may be needed to level

dishwasher.)

Helpful Tip: Be sure to accurately measure dimensions and

ensure dishwasher is level if the floor in the dishwasher opening is

uneven (example: Flooring extends only partway into opening).

NOTE: To avoid shifting during dishwasher operation, shims must

be securely attached to the floor.

If dishwasher will be left unused for a period of time or in a

location where it may be subject to freezing, have it winterized by

authorized service personnel.

Make sure pipes, wires and drain hose are within the shaded area

shown in the "Product and Cabinet Opening Dimensions" section.

i ¸¸¸¸¸¸ql

*Insulation may

be compressed.

(not used on all models)

NOTE: Shaded area of cabinet walls show

where utility connections may

be instal ed.

*Measured from the lowest point on the

underside of countertop. May be reduced to

33%" (86 cm) by removing wheels from

dishwasher.

**Minimum, measured from narrowest point of opening.

Check that all surfaces',

have no protrusions that wpuld

prohibit dishwasher installation,

A new drain hose is supplied with your dishwasher. If drain

hose is not long enough, use a new drain hose with a

maximum length of 12 ft (3.7 m) (Part Number 3385556) that

meets all current AHAM/IAPMO test standards, is resistant to

heat and detergent, and fits the 1" (2.5 cm) drain connector of

the dishwasher.

Make sure to connect drain hose to waste tee or disposer inlet

above drain trap in house plumbing and 20" (50.8 cm)

minimum above the floor. It is recommended that the drain

hose either be looped up and securely fastened to the

underside of the counter, or be connected to an air gap.

Make sure to use an air gap if the drain hose is connected to

house plumbing lower than 20" (50.8 cm) above subfloor or

floor.

Use 1/2"minimum I.D. drain line fittings.

If required, the air gap should be installed in accordance with

the air gap installation instructions. When you are connecting

the air gap, a rubber hose (not provided) will be needed to

connect to the waste tee or disposer inlet.

pp)y 58eq(s emen s

A hot water line with 20 to 120 psi (188 to 862 kPa) water

pressure can be verified by a licensed plumber.

120°F (49°C) water at dishwasher.

3/8"O.D. copper tubing with compression fitting or flexible

braided water supply line (Part Number 4396897RP).

NOTE: 1/2"minimum plastic tubing is not recommended.

A 90° elbow with 3/4"hose connection with rubber washer.

Do not solder within 6" (15.2 cm) of the water inlet valve.

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electrical Code, ANSI/NFPA

70 - latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02269

You must have:

• 120-volt, 60 Hz, AC-only, 15- or 20-amp, fused electrical

supply.

• Copper wire only.

We recommend:

• A time-delay fuse or circuit breaker.

• Aseparate circuit.

If connecting dishwasher with a

power supply cord:

Use UL Listed power supply cord kit

(Part Number 4317824) marked for

use with dishwasher.

Power supply cord must plug into a grounded

3 prong outlet, located in the cabinet next to

the dishwasher opening. Outlet must meet all

local codes and ordinances.

If connecting dishwasher with direct wiring:

• Use flexible, armored or nonmetallic

sheathed, copper wire with

grounding wire that meets the

wiring requirements for your home

and local codes and ordinances.

• Use a UL Listed/CSA Approved strain relief.

INSTALLATIONINSTRUCTIONS

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

I Disconnect electrical power at the fuse boxoi Circuit I

! breaker box before installing diShWaSher. J

i5; ¢i£; ,){(i_)_,_ii;iii i:i!_;;_ii' i!__;i;iiii;;i ii¸i¸__i¸Ii!!!!;;;;;;;;;i;;S;;;;;;;;;!iiI;@;IS¸;()i,);i;iii!;i;i;i!S;£;!{i£;;i;i/;#ii;ii;)i;;i_)iq iii;;;%

shUt off the water supply to the dishWaSher.

;;;i;sss£;;;£s ;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;! ;;i%;

hookups?

_Folow instructi0ns !n the !,Prepare Cabinet

Opening--EXisting Utiities section:

NouFoloW instruCtions in the Prepare cabinet

openiig_New Ut!lities 'seCtiOn:

_: Existing Utility hookups ity hookups

Water line _

Existng Ulliies

If the water line and the cable extend to the locations shown,

proceed to the "Install Drain Hose" section. If they do not reach far

enough, follow the instructions in the "Prepare Cabinet Opening--

New Utilities" section.

''%s% = i .,_

ew U _s

Prepare and route the electrical supply

connection will you use?

Option A, Power Supply Cord:

NOTE: A grounded 3 prong outlet is required inside a cabinet next

to the dishwasher cabinet opening.

S Power Supply Cord--Drill

Uptonal location

Drill a 1Y2"(3.8 cm) hole in cabinet side or rear.

See "Product and Cabinet Opening Dimensions" section.

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover hole with grommet included with power

supply cord kit.

Option B, Direct Wire:

Helpful Tip: Wiring the dishwasher will be easier if you route the

cable into the cabinet opening from the right-hand side.

irect Wire m Drill ho

Optional_locatior

:Y4!'

ii: iliiii!i

Drill a3/4"(1.9 cm) hole in right-hand cabinet side or rear.

See "Product and Cabinet Opening Dimensions" section.

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover hole with grommet (Part Number 302797 -

not provided).

Route cable from power supply through cabinet hole (cable must

extend to the right front side of cabinet opening). Tape cable to

the floor in area shown. This will prohibit cable from moving when

dishwasher is moved into cabinet opening.

P epcs_e c_s_d_8o_e 4£:_<___ e

Helpful Tip: Routing the water line through the left side of cabinet

opening will make water connection easier.

Drill a V2"(1.3 cm) hole in the cabinet side or rear.

_, ;s;;;;;;; xxx> ; ; ;s;;;;;;;;;;;;;;;; s¸;;;;;;;;;;;;;_;s; s;;;;;__ ;;;;;s;; ;;;;;;;s;;;;;;;;;;;;s ;;ss _; s;;;;;;;;;;;;;;;

_, _ '_i_!'iii_i_!!__!_!ii!i_Ii?_!!!!_i_!iiiiiiiiii

Measure overall length of copper tubing or flexible braided water

supply line. Attach to the hot water line using a connection

configuration that is in compliance with local codes and

ordinances. The water line to the dishwasher should have a

manual shutoff valve.

Slowlyroutewatersupplylinethroughholeincabinet.(Ifyouare

usingcoppertubing,itwillbendandkinkeasily,sobegentle.)It

shouldbefarenoughintothecabinetopeningtoconnectittothe

dishwasherinletonthefrontleftsideofthedishwasher.

Slowlyturnwatershutoffvalveto"ON"position.Flushwaterinto

ashallowpanuntilcleartogetridofparticlesthatcouldclogthe

inletvalve.Turnshutoffvalveto"OFF"position.

Coppertubingonly:Slidenut,thenferrule,about1"(2.5cm)onto

coppertubing.

NOTE:Toavoidvibrationduringoperation,routethewatersupply

linesothatitdoesnottouchthedishwasherbase,frameormotor.

Connectthe3/8"compressionfittingtothewatersupplylineprior

toinstallingtheunitintothecabinetopening.Attachsuchthatthe

3/4"connectionisfacingupwardasshownabove.

Coppertubingonly:Putthetubingintothe90°elbowfittingasfar

asitwillgo(thecoppertubingbendsandkinkseasily).Slidethe

nutandferruleforwardandstartthenutontotheelbowthreads.

Flexiblebraidedconnection:Securenuttoelbowusing3/8"open

endedwrenchoradjustablewrench.

NOTE:DonotuseTeflon®ttapewithcompressionfittings.

IMPORTANT:Alwaysuseanewdrainhose.Checklocalcodesto

determinewhetheranairgapisrequired.

Ifneeded,drilla1V2"(3.8 cm) diameter hole in cabinet wall or side

of the opening closest to the sink.

Route drain hose as shown through hole in cabinet to the front

center of opening where drain connection will be made. Tape

drain hose to the floor in area shown. This will prohibit it from

moving when dishwasher is moved into cabinet opening.

1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

Connect drain hose to waste tee Or Waste disp0ser

using one 0fthe f011owing OPtiOnS:

: Opt!0n A; waste d!sP0se[, n0 air gap

Opti0nB;' N0 waste disposer _ no air gap

Option C, Waste disposer, with air gap

Option D, N0 waste diSP0ser _with air gap

IMPORTANT: The drain hose connection of the disposer or a

waste tee must be made before the drain trap and at least 20"

(50.8 cm) above the floor where the dishwasher will be installed.

Helpful Tip: To reduce vibration of the hose, keep the hose away

from the floor.

Option A, Waste disposer - no air gap

_i_iiii!iiii¸_ii!ii¸!__!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!i¸!;!;i; ;!i

1. Using a hammer and screwdriver,

knock plug into disposer.

2. Use needle-nose pliers to remove

plug.

Attach drain hose to disposer inlet

with large silver drain hose clamp

(provided). Use pliers to squeeze

clamp open and move into position.

Option B, No waste disposer - no air gap

iiii .....

1. Connect black end of drain hose to

waste tee and cut if needed.

NOTE: Do not cut ribbed section.

2. Attach black end of drain hose to

waste tee with a large silver drain

hose clamp (provided). Use pliers to

squeeze clamp open and move into

position. If the drain hose was cut,

use a 1_/2"to 2" (3.8 to 5 cm) screw-

type clamp (not provided).

Option C, Waste disposer - with air gap

i iii

Drain trap

1. Using a hammer and screwdriver,

knock plug into disposer.

2. Use needle-nose pliers to remove

plug.

3. Connect black end of drain hose to

air gap and cut if needed.

NOTE: Do not cut ribbed section.

Attach drain hose to air gap with

large silver drain hose clamp

(provided). Use pliers to squeeze

clamp open and move into position.

If the drain hose was cut, use a 1W'

to 2" (3.8 to 5 cm) screw-type clamp

(not provided).

Use a rubber hose (not provided)

with screw-type clamps (not

provided) to connect from air gap to

disposer inlet.

Option D, No waste disposer - with air gap

Connect black end of drain hose to

air gap and cut if needed.

NOTE: Do not cut ribbed section.

Attach drain hose to air gap with

large silver drain hose clamp

(provided). Use pliers to squeeze

clamp open and move into position.

If the drain hose was cut, use a 1V2"

to 2" (3.8 to 5.1 cm) screw-type

clamp (not provided).

Use a rubber hose (not provided)

with screw-type clamps (not

provided) to connect from waste tee

to air gap.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Using the precut slots in the insulation, fasten the insulation over

the molded hooks on the tub. Be sure to fasten the insulation

down on both sides of the tub.

Helpful Tip: Place cardboard under dishwasher until installed in

cabinet opening to avoid damaging floor covering. Do not use

door panel as a worktable without first covering with a towel to

avoid scratching the door panel.

Using two or more people, grasp sides of dishwasher door frame

and place dishwasher on its back.

Using a flat-blade screwdriver, turn the plastic fasteners 1/4turn to

unlock them. Remove panel. Do not remove tech sheet from

access panel.

Using a 1/4"hex head socket, nut driver or Phillips screwdriver,

remove terminal box cover. Retain for later use.

Install a UL Listed/CSA Approved strain relief. Make sure screw

heads are facing to the left when tightening conduit nut. Strain

relief is provided with the power supply cord kit.

connection will you use?

__ Power Supply Cord:

Follow Option A instructions

Direct Wi re"

- , Follow Option B instructions

NOTE: If using Option B, proceed to "Determine Cabinet

Opening," to continue with the installation of your dishwasher.

Option A, Power Supply Cord:

Route cord so that it does not touch dishwasher motor to lower

part of dishwasher tub. Pull cord through strain relief in terminal

box.

Select UL Listed/CSA Approved twist-on wire connectors rated to

connect your power supply cord to 16-gauge dishwasher wiring.

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in

terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

2_ Power Supply Cord=

Connect ground wire

.... l

he)

Remove the green grounding screw and place through the ring

terminal of the green ground wire. Reattach and tighten the green

screw.

NOTE: Do not pre-twist stranded wire. Twist on wire connector.

Gently tug on wires to be sure both are secured.

Connect wires black to black and white to white, using UL

Listed/CSA Approved twist-on wire connectors.

If needed, see website for animated representation of this step.

Visit www.whirlpool.com under FAQ tab.

41 Power Cord-Secure cor

--" on strain relief

Tighten strain relief screws to secure cord.

Place wires inside terminal box. Insert tabs on left side of cover.

Make sure wires are tucked inside box. Close cover ensuring

wires are not pinched. Use 1/4"nut driver and previously removed

screw to secure cover.

NOTE: Do not plug into outlet until instructed to do so.

Measure height of cabinet opening from underside of countertop

to floor where dishwasher will be installed (you will need to

measure the lowest point on the underside of the countertop and

the highest point on the floor). Refer to "Dishwasher Height

Adjustment Chart" for wheel position and the number of turns

needed.

! II

33%" (86.0 cm) Removed All the way up

u |

34" (86,4 cm) .1 10

• j

NOTE: If the minimum cabinet opening height is less than

34" (86.4 cm), the rear wheels can be removed for additional

clearance. This will allow the dishwasher to fit into a 337/8'' (86 cm)

high cabinet opening, but the dishwasher will be more difficult to

move. (Measurements are approximate. Wheels and legs are

preset at the factory for 34W' [87.6 cm].)

Turn both leveler legs to the same height. Put wheels in the

required position determined from "Dishwasher Height

Adjustment Chart." To change wheel position, use a flat-blade

screwdriver to pop out the wheel, then snap into the new position.

Built-up floors: If the kitchen floor is higher than the cabinet

opening's floor - for example, the kitchen floor tile does not

extend into the cabinet opening - add shims as needed in the area

shown to bring the dishwasher up to 34" (86.4 cm) below the

countertop.

NOTE: Shims must be securely attached to floor to avoid

movement when the dishwasher is in use.

C,_OOS@ A _'_ ..... _:_' C_'ss_t ....

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Using 2 or more people, stand the dishwasher up.

IMPORTANT: The dishwasher must be secured to the cabinet.

There are two brackets found in the parts bag. Attach the

brackets using Option Number 1 if the countertop is wood,

laminate or another similar surface. If your countertop is marble,

granite or another hard surface, install using Option Number 2.

Option 1, Countertop Attachment

11 Insert bracket

Remove the brackets from the package and insert into the open

slots on the left and right-hand top of the dishwasher collar as

shown.

Using a pair of pliers, bend the tab down to secure the bracket in

place. Repeat this step for the other side.

NOTE: Do not attach the dishwasher. This will be done later.

Option 2, Side Attachment

For marble, granite, or other hard surface countertops

Order Mounting Bracket Kit Part Number 8212560.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

1JStand dishwasher upright

Using 2 or more people, stand dishwasher upright.

NOTE: Do not install kick plate until instructed to do so.

IMPORTANT: Double-check correct placement of utilities. Grasp

the sides of the dishwasher at the edges of the door panel. Tilt

dishwasher backward on wheels and move dishwasher close to

cabinet opening.

NOTE: Do not push on the front of the panel or on the console.

Panel or console may dent.

Helpful Tip: Temporarily tape utilities to the floor in the locations

shown to prohibit them from moving when dishwasher is moved

into the cabinet opening.

Check that water line is on the left side of opening and drain hose

is near the center of the cabinet opening.

Open and close door

With another person holding the dishwasher to keep it from

tipping, open and close the door a few times. Ifthe door closes or

falls open under its own weight, the door tension will need to be

adjusted.

If the door closes too quickly, decrease the spring tension by

moving the spring end toward the front of the dishwasher.

NOTE: Springs should be in the same notches on left and right

sides.

Door falls open m

Increase spring tension

If the door falls open, increase the spring tension by moving the

spring end toward the back of the dishwasher.

NOTE: Springs should be in the same notches on left and right

sides.

IMPORTANT: If wheels were removed, cover the floor when

moving the dishwasher. Slowly move dishwasher completely into

cabinet opening. Do not kink or pinch water line, drain hose,

power supply cord or direct wire between dishwasher and

cabinet. Remove cardboard from under dishwasher.

NOTES:

• It is all right if dishwasher fits tightly into cabinet opening. Do

not remove insulation blanket- the blanket reduces the sound

level.

• If using power cord, make sure to route end through hole in

cutout before sliding dishwasher into cabinet opening.

Align front of dishwasher door panel with front of cabinet doors.

You may need to adjust alignment to be even with your cabinets.

Check that leveling legs are firmly against the floor. Close and

latch the door, and place level against the front panel. Check that

dishwasher is centered from front to back in the opening. If

needed, adjust leveling leg until dishwasher is plumb. Repeat for

other side of dishwasher.

Helpful Tip: Push up on front of dishwasher to raise dishwasher

off the ground to adjust front legs. With some installations, it may

be easier to adjust the front leg using the 3A6"hex head socket or

adjustable wrench.

Place level against top front opening of tub. Check that

dishwasher is level from side-to-side. If dishwasher is not level,

adjust front legs up or down until dishwasher is level.

Be sure rubber washer is properly seated in fitting. Slide the 3/4"

fitting up to the valve and hand tighten to avoid cross-threading.

Hand tighten until the coupling is tight.

Using pliers, check the tightness of the coupling. An additional 1/4

to 1/2turn may be required to seal the rubber gasket.

NOTE: Do not overtighten. Damage to the coupling can result.

Place paper towel under 90° elbow fitting. Turn on water supply

and check for leaks. If leak occurs, repeat previous step.

If needed, see website for animated representation of this step.

Visit www.whirlpool.com/watersupply under FAQ tab.

NOTE: Do not use Teflon ®ttape with compression fittings.

t®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

Place towel under drain hose to catch any water in drain hose.

Place the small green drain hose clamp onto the small end of the

drain hose. Push the new drain hose into the black drain hose

connector up to the drain hose stop.

Using pliers, squeeze open the small green drain hose clamp and

slide onto connector between stops.

Drain hose

Black drain hose

connector --

Green clamp

After hose is connected, remove towel.

If needed, see website for animated representation of this step.

Visit www.whirlpool.com/drain under FAQ tab.

..... _ ......(gti @C__s_ _._s:J_'_S_ss_s,, s.,_,._

NOTE: Ifthe power supply cord was connected earlier, proceed to

"Secure Dishwasher in Cabinet Opening" section.

Option B, Direct Wire:

Route cable so that it does not touch dishwasher motor or lower

part of dishwasher tub. Pull cable through UL Listed/CSA

Approved strain relief in terminal box. Strain relief is not supplied

with the dishwasher. Owner must purchase a 7/8"screw-in type

strain relief.

Select UL Listed/CSA Approved twist-on wire connectors (not

included) rated to connect your household wiring to 16-gauge

dishwasher wiring.

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in

terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Form bare ground wire into a U-shaped hook. Wrap ground wire

hook clockwise around ground connector screw and under the

washer. Securely tighten ground connector.

NOTE: Do not pre-twist stranded wire. Twist on UL listed/CSA

approved wire connector. Gently tug on wires to be sure both are

secured.

Connect wires black to black and white to white, using UL

Listed/CSA Approved twist-on wire connectors (not included).

If needed, see website for animated representation of this step.

Visit www.whirlpool.com/electrical under FAQ tab.

Tighten strain relief screws to secure cable.

Place wires inside terminal box. Insert tabs on left side of cover.

Make sure wires are tucked inside box. Close cover ensuring

wires are not pinched. Use 1/4"nut driver and previously removed

screw to secure cover.

Check that dishwasher is still level front-to-back and side-to-side in

cabinet opening.

IMPORTANT: If you have solid countertops such as Corian% granite,

etc., you must use side mounting kit (Part Number 8212560). Follow

kit instructions. (Brackets included with kit.)

Open dishwasher door, remove lower dish rack, and place towel over

pump assembly and lower spray arm of dishwasher. This will keep

screws from falling into pump area when you are securing dishwasher

to countertop.

NOTE: Do not drop screws into bottom of dishwasher.

Locate brackets on top of dishwasher and secure dishwasher to

countertop with two, #10 x 1/2"Phillips-head screws (included). The

dishwasher must be secured to keep it from shifting when door is

opened.

1-®Corian is a registered trademark of E.I. Du Pont De Nemours and Company.

Check that top of door does not contact screws, brackets or

countertop. If it does, adjust leveling legs.

Open door and check that space between dishwasher cabinet

opening and tub is equal on both sides. If spacing is not equal,

loosen bracket screws secured and shift tub. Tighten bracket

screws.

Remove towel from dishwasher. Reinstall the lower dish rack.

If needed, see website for animated representation of this step.

Visit www.whirlpool.com/anchoring under FAQ tab.

lJ Reinstall_ccess panel and

Insul

(on some models

Place the plastic access panel against the dishwasher leg.

Check that the lower edge of the access panel touches the floor.

Adjust if necessary.

Using a flat-blade screwdriver, turn the fasteners /4 turn to lock

into place. The fastener's slot will be straight up and down when

properly locked.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Plug intoa grounded 3 prong outlet. Check that power supply

cord does not touch dishwasher motor or lower part of

dishwasher tub.

Reconnect Power

• Read the Dishwasher User Instructions that came with your

dishwasher.

Check that all parts have been installed and no steps were

skipped. Check that you have all tools used.

Start dishwasher and allow it to complete the shortest wash

cycle. After the first 2 minutes, unlatch door, wait 5 seconds,

then open door. Check that there is water in the bottom of the

dishwasher tub. Check that dishwasher is working properly.

If the dishwasher is not working properly, disconnect power or

unplug dishwasher and see "If Dishwasher Does Not Operate"

section.

First try the solutions suggested here to possibly avoid the cost of

a service call.

• Has the circuit breaker tripped or the house fuse blown?

• Is the door closed tightly and latched?

• Has the cycle been set correctly to start the dishwasher?

• Is the water turned on?

If none of these possible solutions work, call 1-800-253-1301, or

in Canada, call 1-800-807-6777.

Expect longer wash times. Your new dishwasher will average

2-3 hours per load, but use nearly 40% less energy than older

models. Designed with a low wattage, low energy consumption

motor, your dishwasher washes longer to ensure exceptional

cleaning. Certain models are equipped with an optical water

sensor so the first cycle will run longer to calibrate to optical

sensor. Selecting certain options could increase cycle time past

3.5 hours.

Rinse Aid is necessary for good drying results:

This dishwasher is designed to be used with rinse aid for good

drying performance and controlling hard water deposit buildup.

Energy efficient dishwashers use less water and energy, so they

depend on the water sheeting action of rinse aid for good drying

performance.

Start/Resume light may flash:

When pressing Start/Resume, you must make sure the door is

closed within 3 seconds. If you do not close the door within

3 seconds, the Start/Resume light will flash until you press it

again. (You must also do this when adding a dish during the

middle of a cycle.)

NOTE: If a braided supply hose is used, replace inlet hose after

5 years to reduce the risk of hose failure. Record hose installation

or replacement dates on the hose for future reference.

La page charge ...

Magic Chef CDB7000AWB4 Guide d'installation

Marque: Magic Chef

Modèle: CDB7000AWB4

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Magic Chef CDB7000AWB4 Installation guide

Magic Chef CDB7000AWB4 Guide d'installation

Ce manuel convient également à

Magic Chef CDB7000AWB4 Guide d'installation

dans d''autres langues

Autres documents