Magic Chef CDB7000AWB4 Guide d'installation

Catégorie
Lave-vaisselle
Taper
Guide d'installation

Ce manuel convient également à

INSTALLATIONINSTRUCTIONS
UNDERCOUNTERDISHWASHER
PLASTICGIANT TUBMODELS
INSTRUCTIONSD'INSTALLATION
LAVE-VAISSELLESOUSCOMPTOIR
MODELESA TRESGRANDE CUVE EN PLASTIQUE
Table of Contents .............................................................. 2
Table des matieres .......................................................... 21
W10329310A
TABLEOF CONTENTS
DISHWASHER SAFETY ............................................................................... 2
INSTALLATION REQUIREMENTS ............................................................. 3
Tools and Parts ......................................................................................... 3
Location Requirements ............................................................................. 3
Drain Requirements .................................................................................. 5
Water Supply Requirements ..................................................................... 5
Electrical Requirements ............................................................................ 5
INSTALLATION INSTRUCTIONS ............................................................... 6
Prepare Cabinet Opening--Existing Utilities ............................................ 6
Prepare Cabinet Opening-- New Utilities ................................................. 6
Prepare and Route Water Line ................................................................. 7
Install Drain Hose ...................................................................................... 8
Prepare Dishwasher ................................................................................ 10
INSTALLATION INSTRUCTIONS (CONT.)
Make Power Supply Cord Connection .................................................. 11
Determine Cabinet Opening ................................................................... 13
Choose Attachment Option .................................................................... 13
Move Dishwasher Close to Cabinet Opening ........................................ 14
Connect to Water Supply ....................................................................... 16
Connect to Drain ..................................................................................... 16
Make Direct Wire Electrical Connection ................................................. 17
Secure Dishwasher in Cabinet Opening ................................................ 18
Complete Installation .............................................................................. 19
Check Operation ..................................................................................... 20
If Dishwasher Does Not Operate ............................................................ 20
Additional Tips ........................................................................................ 20
DISHWASHERSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
You Need to:
Slowly open dishwasher door while someone grasps the rear
of the dishwasher. Remove shipping materials, drain hose and
lower rack. Close dishwasher door until latched.
Observe all governing codes and ordinances.
Install this dishwasher as specified in these instructions.
Installation should be performed by a qualified service
technician. The dishwasher must be installed to meet all
electrical and plumbing national and local codes and
ordinances.
2
INSTALLATION
REQUIREMENTS
Gather the recommended tools and parts before starting
installation. Read and follow the instructions 3rovided with any
tools listed here.
All Installations
Toolsneeded:
%0"and I/4"
nut drivers or
heX soCkets
Measuring tape
or ruler
10" adjustable wrenc
that opens to
11/8,!(2,9 cm)
UL LiSted/CSA _
APPrOVed twist-on U
wire connectors*
*Must be the proper size to connect your household wiring to
16-gauge wiring in dishwasher.
Other useful items you may need:
Parts supplied:
Silver Green
Make sure all these parts are included in the literature package.
Parts needed:
%" compr ×¾, hose fitting
For part or kit, see local
retailer or call Whirlp0ol
Parts! 1,800-442-9991, Part
Number W10273460
Other parts you may also need:
1'/2" " Sidem0unting kit
--2
(38:!_ 5 cm) for solid surface Idu_
_Screw:type I c0untertops I
[clamPs(3 maximum)J (Part Number I8212560) J
NOTE: Parts available for purchase in plumbing supply stores.
Check local codes. Check existing electrical supply. See
"Electrical Requirements" section. It is recommended that
electrical connections be made by a licensed electrical installer.
In addition, for first-time installations
Tools needed:
with 1/2i[3/4_ Y/_ ] _
and 11/2 hole _/_ ] Sma
sawbks _ ] tubing cutter wire stripper
Parts needed:
CopPer tubing (3/_'! See "Electrical Requirements,, secti0nl
O.D Suggested)or
flexibebadedlr i For Direct Wire'., For Power Supply
water suna v ne use UL Dsted/ Cord: use UL
CSA Approved Listed/CSA
I strain App[oved power
tttt,tt. Ito fit % (2,2 m) supply cord kit
hole marked for use with
dishwasher
Grounded electrical supply required.
Do not run drain lines, water lines or electrical wiring where they
can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must provide
clearance between motor and flooring. Motor should not touch
the floor.
Do not install dishwasher over carpeted flooring.
Shelter dishwasher and water lines leading to dishwasher against
freezing. Damage from freezing is not covered by the warranty.
A side panel kit is available from your dealer for installing your
dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part Number 4396277) is available
from your dealer for installing underneath the countertop.
Check location where dishwasher will be installed. The location
must provide:
easy access to water, electricity and drain.
convenient access for loading and unloading dishes.
Corner locations require a 2" (5.1 cm) minimum clearance
between the side of the dishwasher door and the wall or
cabinet.
square opening for proper operation and appearance.
cabinet front perpendicular to floor.
level floor. (If floor at front of opening is not level with floor
at rear of opening, shims may be needed to level
dishwasher.)
Helpful Tip: Be sure to accurately measure dimensions and
ensure dishwasher is level if the floor in the dishwasher opening is
uneven (example: Flooring extends only partway into opening).
NOTE: To avoid shifting during dishwasher operation, shims must
be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it winterized by
authorized service personnel.
Make sure pipes, wires and drain hose are within the shaded area
shown in the "Product and Cabinet Opening Dimensions" section.
i ¸¸¸¸¸¸ql
*Insulation may
be compressed.
(not used on all models)
NOTE: Shaded area of cabinet walls show
where utility connections may
be instal ed.
*Measured from the lowest point on the
underside of countertop. May be reduced to
33%" (86 cm) by removing wheels from
dishwasher.
**Minimum, measured from narrowest point of opening.
Check that all surfaces',
have no protrusions that wpuld
prohibit dishwasher installation,
A new drain hose is supplied with your dishwasher. If drain
hose is not long enough, use a new drain hose with a
maximum length of 12 ft (3.7 m) (Part Number 3385556) that
meets all current AHAM/IAPMO test standards, is resistant to
heat and detergent, and fits the 1" (2.5 cm) drain connector of
the dishwasher.
Make sure to connect drain hose to waste tee or disposer inlet
above drain trap in house plumbing and 20" (50.8 cm)
minimum above the floor. It is recommended that the drain
hose either be looped up and securely fastened to the
underside of the counter, or be connected to an air gap.
Make sure to use an air gap if the drain hose is connected to
house plumbing lower than 20" (50.8 cm) above subfloor or
floor.
Use 1/2"minimum I.D. drain line fittings.
If required, the air gap should be installed in accordance with
the air gap installation instructions. When you are connecting
the air gap, a rubber hose (not provided) will be needed to
connect to the waste tee or disposer inlet.
pp)y 58eq(s emen s
A hot water line with 20 to 120 psi (188 to 862 kPa) water
pressure can be verified by a licensed plumber.
120°F (49°C) water at dishwasher.
3/8"O.D. copper tubing with compression fitting or flexible
braided water supply line (Part Number 4396897RP).
NOTE: 1/2"minimum plastic tubing is not recommended.
A 90° elbow with 3/4"hose connection with rubber washer.
Do not solder within 6" (15.2 cm) of the water inlet valve.
Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electrical Code, ANSI/NFPA
70 - latest edition and all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02269
You must have:
120-volt, 60 Hz, AC-only, 15- or 20-amp, fused electrical
supply.
Copper wire only.
We recommend:
A time-delay fuse or circuit breaker.
Aseparate circuit.
If connecting dishwasher with a
power supply cord:
Use UL Listed power supply cord kit
(Part Number 4317824) marked for
use with dishwasher.
Power supply cord must plug into a grounded
3 prong outlet, located in the cabinet next to
the dishwasher opening. Outlet must meet all
local codes and ordinances.
If connecting dishwasher with direct wiring:
Use flexible, armored or nonmetallic
sheathed, copper wire with
grounding wire that meets the
wiring requirements for your home
and local codes and ordinances.
Use a UL Listed/CSA Approved strain relief.
INSTALLATIONINSTRUCTIONS
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
I Disconnect electrical power at the fuse boxoi Circuit I
! breaker box before installing diShWaSher. J
i5; ¢i£; ,){(i_)_,_ii;iii i:i!_;;_ii' i!__;i;iiii;;i ii¸__i¸Ii!!!!;;;;;;;;;i;;S;;;;;;;;;!iiI;@;IS¸;()i,);i;iii!;i;i;i!S;£;!{i£;;i;i/;#ii;ii;)i;;i_)iq iii;;;%
shUt off the water supply to the dishWaSher.
;;;i;sss£;;;£s ;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;!;! ;;i%;
hookups?
_Folow instructi0ns !n the !,Prepare Cabinet
Opening--EXisting Utiities section:
NouFoloW instruCtions in the Prepare cabinet
openiig_New Ut!lities 'seCtiOn:
_: Existing Utility hookups ity hookups
Water line _
Existng Ulliies
If the water line and the cable extend to the locations shown,
proceed to the "Install Drain Hose" section. If they do not reach far
enough, follow the instructions in the "Prepare Cabinet Opening--
New Utilities" section.
''%s% = i .,_
ew U _s
Prepare and route the electrical supply
connection will you use?
Option A, Power Supply Cord:
NOTE: A grounded 3 prong outlet is required inside a cabinet next
to the dishwasher cabinet opening.
S Power Supply Cord--Drill
Uptonal location
Drill a 1Y2"(3.8 cm) hole in cabinet side or rear.
See "Product and Cabinet Opening Dimensions" section.
6
Wood cabinet: Sand the hole until smooth.
Metal cabinet: Cover hole with grommet included with power
supply cord kit.
Option B, Direct Wire:
Helpful Tip: Wiring the dishwasher will be easier if you route the
cable into the cabinet opening from the right-hand side.
irect Wire m Drill ho
Optional_locatior
:Y4!'
ii: iliiii!i
Drill a3/4"(1.9 cm) hole in right-hand cabinet side or rear.
See "Product and Cabinet Opening Dimensions" section.
Wood cabinet: Sand the hole until smooth.
Metal cabinet: Cover hole with grommet (Part Number 302797 -
not provided).
Route cable from power supply through cabinet hole (cable must
extend to the right front side of cabinet opening). Tape cable to
the floor in area shown. This will prohibit cable from moving when
dishwasher is moved into cabinet opening.
P epcs_e c_s_d_8o_e 4£:_<___ e
Helpful Tip: Routing the water line through the left side of cabinet
opening will make water connection easier.
Drill a V2"(1.3 cm) hole in the cabinet side or rear.
_, ;s;;;;;;; xxx> ; ; ;s;;;;;;;;;;;;;;;; s¸;;;;;;;;;;;;;_;s; s;;;;;__ ;;;;;s;; ;;;;;;;s;;;;;;;;;;;;s ;;ss _; s;;;;;;;;;;;;;;;
_, _ '_i_!'iii_i_!!__!_!ii!i_Ii?_!!!!_i_!iiiiiiiiii
Measure overall length of copper tubing or flexible braided water
supply line. Attach to the hot water line using a connection
configuration that is in compliance with local codes and
ordinances. The water line to the dishwasher should have a
manual shutoff valve.
Slowlyroutewatersupplylinethroughholeincabinet.(Ifyouare
usingcoppertubing,itwillbendandkinkeasily,sobegentle.)It
shouldbefarenoughintothecabinetopeningtoconnectittothe
dishwasherinletonthefrontleftsideofthedishwasher.
Slowlyturnwatershutoffvalveto"ON"position.Flushwaterinto
ashallowpanuntilcleartogetridofparticlesthatcouldclogthe
inletvalve.Turnshutoffvalveto"OFF"position.
Coppertubingonly:Slidenut,thenferrule,about1"(2.5cm)onto
coppertubing.
NOTE:Toavoidvibrationduringoperation,routethewatersupply
linesothatitdoesnottouchthedishwasherbase,frameormotor.
Connectthe3/8"compressionfittingtothewatersupplylineprior
toinstallingtheunitintothecabinetopening.Attachsuchthatthe
3/4"connectionisfacingupwardasshownabove.
Coppertubingonly:Putthetubingintothe90°elbowfittingasfar
asitwillgo(thecoppertubingbendsandkinkseasily).Slidethe
nutandferruleforwardandstartthenutontotheelbowthreads.
Flexiblebraidedconnection:Securenuttoelbowusing3/8"open
endedwrenchoradjustablewrench.
NOTE:DonotuseTeflon®ttapewithcompressionfittings.
IMPORTANT:Alwaysuseanewdrainhose.Checklocalcodesto
determinewhetheranairgapisrequired.
Ifneeded,drilla1V2"(3.8 cm) diameter hole in cabinet wall or side
of the opening closest to the sink.
Route drain hose as shown through hole in cabinet to the front
center of opening where drain connection will be made. Tape
drain hose to the floor in area shown. This will prohibit it from
moving when dishwasher is moved into cabinet opening.
1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.
8
Connect drain hose to waste tee Or Waste disp0ser
using one 0fthe f011owing OPtiOnS:
: Opt!0n A; waste d!sP0se[, n0 air gap
Opti0nB;' N0 waste disposer _ no air gap
Option C, Waste disposer, with air gap
Option D, N0 waste diSP0ser _with air gap
IMPORTANT: The drain hose connection of the disposer or a
waste tee must be made before the drain trap and at least 20"
(50.8 cm) above the floor where the dishwasher will be installed.
Helpful Tip: To reduce vibration of the hose, keep the hose away
from the floor.
Option A, Waste disposer - no air gap
_i_iiii!iiii¸_ii!ii¸!__!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!i¸!;!;i; ;!i
1. Using a hammer and screwdriver,
knock plug into disposer.
2. Use needle-nose pliers to remove
plug.
3.
Attach drain hose to disposer inlet
with large silver drain hose clamp
(provided). Use pliers to squeeze
clamp open and move into position.
Option B, No waste disposer - no air gap
iiii .....
1. Connect black end of drain hose to
waste tee and cut if needed.
NOTE: Do not cut ribbed section.
2. Attach black end of drain hose to
waste tee with a large silver drain
hose clamp (provided). Use pliers to
squeeze clamp open and move into
position. If the drain hose was cut,
use a 1_/2"to 2" (3.8 to 5 cm) screw-
type clamp (not provided).
Option C, Waste disposer - with air gap
i iii
Drain trap
1. Using a hammer and screwdriver,
knock plug into disposer.
2. Use needle-nose pliers to remove
plug.
3. Connect black end of drain hose to
air gap and cut if needed.
NOTE: Do not cut ribbed section.
4=
5=
Attach drain hose to air gap with
large silver drain hose clamp
(provided). Use pliers to squeeze
clamp open and move into position.
If the drain hose was cut, use a 1W'
to 2" (3.8 to 5 cm) screw-type clamp
(not provided).
Use a rubber hose (not provided)
with screw-type clamps (not
provided) to connect from air gap to
disposer inlet.
Option D, No waste disposer - with air gap
,
2.
Connect black end of drain hose to
air gap and cut if needed.
NOTE: Do not cut ribbed section.
Attach drain hose to air gap with
large silver drain hose clamp
(provided). Use pliers to squeeze
clamp open and move into position.
If the drain hose was cut, use a 1V2"
to 2" (3.8 to 5.1 cm) screw-type
clamp (not provided).
Use a rubber hose (not provided)
with screw-type clamps (not
provided) to connect from waste tee
to air gap.
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
Using the precut slots in the insulation, fasten the insulation over
the molded hooks on the tub. Be sure to fasten the insulation
down on both sides of the tub.
Helpful Tip: Place cardboard under dishwasher until installed in
cabinet opening to avoid damaging floor covering. Do not use
door panel as a worktable without first covering with a towel to
avoid scratching the door panel.
Using two or more people, grasp sides of dishwasher door frame
and place dishwasher on its back.
10
Using a flat-blade screwdriver, turn the plastic fasteners 1/4turn to
unlock them. Remove panel. Do not remove tech sheet from
access panel.
Using a 1/4"hex head socket, nut driver or Phillips screwdriver,
remove terminal box cover. Retain for later use.
Install a UL Listed/CSA Approved strain relief. Make sure screw
heads are facing to the left when tightening conduit nut. Strain
relief is provided with the power supply cord kit.
connection will you use?
__ Power Supply Cord:
Follow Option A instructions
Direct Wi re"
- , Follow Option B instructions
J
NOTE: If using Option B, proceed to "Determine Cabinet
Opening," to continue with the installation of your dishwasher.
Option A, Power Supply Cord:
_s
Route cord so that it does not touch dishwasher motor to lower
part of dishwasher tub. Pull cord through strain relief in terminal
box.
Select UL Listed/CSA Approved twist-on wire connectors rated to
connect your power supply cord to 16-gauge dishwasher wiring.
11
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector in
terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
2_ Power Supply Cord=
Connect ground wire
.... l
o
he)
Remove the green grounding screw and place through the ring
terminal of the green ground wire. Reattach and tighten the green
screw.
NOTE: Do not pre-twist stranded wire. Twist on wire connector.
Gently tug on wires to be sure both are secured.
Connect wires black to black and white to white, using UL
Listed/CSA Approved twist-on wire connectors.
If needed, see website for animated representation of this step.
Visit www.whirlpool.com under FAQ tab.
41 Power Cord-Secure cor
--" on strain relief
0
Tighten strain relief screws to secure cord.
Place wires inside terminal box. Insert tabs on left side of cover.
Make sure wires are tucked inside box. Close cover ensuring
wires are not pinched. Use 1/4"nut driver and previously removed
screw to secure cover.
NOTE: Do not plug into outlet until instructed to do so.
12
Measure height of cabinet opening from underside of countertop
to floor where dishwasher will be installed (you will need to
measure the lowest point on the underside of the countertop and
the highest point on the floor). Refer to "Dishwasher Height
Adjustment Chart" for wheel position and the number of turns
needed.
! II
33%" (86.0 cm) Removed All the way up
u |
34" (86,4 cm) .1 10
j
NOTE: If the minimum cabinet opening height is less than
34" (86.4 cm), the rear wheels can be removed for additional
clearance. This will allow the dishwasher to fit into a 337/8'' (86 cm)
high cabinet opening, but the dishwasher will be more difficult to
move. (Measurements are approximate. Wheels and legs are
preset at the factory for 34W' [87.6 cm].)
Turn both leveler legs to the same height. Put wheels in the
required position determined from "Dishwasher Height
Adjustment Chart." To change wheel position, use a flat-blade
screwdriver to pop out the wheel, then snap into the new position.
Built-up floors: If the kitchen floor is higher than the cabinet
opening's floor - for example, the kitchen floor tile does not
extend into the cabinet opening - add shims as needed in the area
shown to bring the dishwasher up to 34" (86.4 cm) below the
countertop.
NOTE: Shims must be securely attached to floor to avoid
movement when the dishwasher is in use.
C,_OOS@ A _'_ ..... _:_' C_'ss_t ....
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
Using 2 or more people, stand the dishwasher up.
IMPORTANT: The dishwasher must be secured to the cabinet.
There are two brackets found in the parts bag. Attach the
brackets using Option Number 1 if the countertop is wood,
laminate or another similar surface. If your countertop is marble,
granite or another hard surface, install using Option Number 2.
Option 1, Countertop Attachment
11 Insert bracket
Remove the brackets from the package and insert into the open
slots on the left and right-hand top of the dishwasher collar as
shown.
13
Using a pair of pliers, bend the tab down to secure the bracket in
place. Repeat this step for the other side.
NOTE: Do not attach the dishwasher. This will be done later.
Option 2, Side Attachment
For marble, granite, or other hard surface countertops
Order Mounting Bracket Kit Part Number 8212560.
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
1JStand dishwasher upright
i
I
i
I
i
Using 2 or more people, stand dishwasher upright.
NOTE: Do not install kick plate until instructed to do so.
IMPORTANT: Double-check correct placement of utilities. Grasp
the sides of the dishwasher at the edges of the door panel. Tilt
dishwasher backward on wheels and move dishwasher close to
cabinet opening.
NOTE: Do not push on the front of the panel or on the console.
Panel or console may dent.
Helpful Tip: Temporarily tape utilities to the floor in the locations
shown to prohibit them from moving when dishwasher is moved
into the cabinet opening.
Check that water line is on the left side of opening and drain hose
is near the center of the cabinet opening.
Open and close door
With another person holding the dishwasher to keep it from
tipping, open and close the door a few times. Ifthe door closes or
falls open under its own weight, the door tension will need to be
adjusted.
14
If the door closes too quickly, decrease the spring tension by
moving the spring end toward the front of the dishwasher.
NOTE: Springs should be in the same notches on left and right
sides.
Door falls open m
Increase spring tension
If the door falls open, increase the spring tension by moving the
spring end toward the back of the dishwasher.
NOTE: Springs should be in the same notches on left and right
sides.
IMPORTANT: If wheels were removed, cover the floor when
moving the dishwasher. Slowly move dishwasher completely into
cabinet opening. Do not kink or pinch water line, drain hose,
power supply cord or direct wire between dishwasher and
cabinet. Remove cardboard from under dishwasher.
NOTES:
It is all right if dishwasher fits tightly into cabinet opening. Do
not remove insulation blanket- the blanket reduces the sound
level.
If using power cord, make sure to route end through hole in
cutout before sliding dishwasher into cabinet opening.
Align front of dishwasher door panel with front of cabinet doors.
You may need to adjust alignment to be even with your cabinets.
Check that leveling legs are firmly against the floor. Close and
latch the door, and place level against the front panel. Check that
dishwasher is centered from front to back in the opening. If
needed, adjust leveling leg until dishwasher is plumb. Repeat for
other side of dishwasher.
Helpful Tip: Push up on front of dishwasher to raise dishwasher
off the ground to adjust front legs. With some installations, it may
be easier to adjust the front leg using the 3A6"hex head socket or
adjustable wrench.
15
Place level against top front opening of tub. Check that
dishwasher is level from side-to-side. If dishwasher is not level,
adjust front legs up or down until dishwasher is level.
Be sure rubber washer is properly seated in fitting. Slide the 3/4"
fitting up to the valve and hand tighten to avoid cross-threading.
Hand tighten until the coupling is tight.
Using pliers, check the tightness of the coupling. An additional 1/4
to 1/2turn may be required to seal the rubber gasket.
NOTE: Do not overtighten. Damage to the coupling can result.
Place paper towel under 90° elbow fitting. Turn on water supply
and check for leaks. If leak occurs, repeat previous step.
If needed, see website for animated representation of this step.
Visit www.whirlpool.com/watersupply under FAQ tab.
NOTE: Do not use Teflon ®ttape with compression fittings.
t®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.
Place towel under drain hose to catch any water in drain hose.
Place the small green drain hose clamp onto the small end of the
drain hose. Push the new drain hose into the black drain hose
connector up to the drain hose stop.
Using pliers, squeeze open the small green drain hose clamp and
slide onto connector between stops.
Drain hose
Black drain hose
connector --
Green clamp
After hose is connected, remove towel.
If needed, see website for animated representation of this step.
Visit www.whirlpool.com/drain under FAQ tab.
16
..... _ ......(gti @C__s_ _._s:J_'_S_ss_s,, s.,_,._
NOTE: Ifthe power supply cord was connected earlier, proceed to
"Secure Dishwasher in Cabinet Opening" section.
Option B, Direct Wire:
Route cable so that it does not touch dishwasher motor or lower
part of dishwasher tub. Pull cable through UL Listed/CSA
Approved strain relief in terminal box. Strain relief is not supplied
with the dishwasher. Owner must purchase a 7/8"screw-in type
strain relief.
Select UL Listed/CSA Approved twist-on wire connectors (not
included) rated to connect your household wiring to 16-gauge
dishwasher wiring.
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector in
terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Form bare ground wire into a U-shaped hook. Wrap ground wire
hook clockwise around ground connector screw and under the
washer. Securely tighten ground connector.
NOTE: Do not pre-twist stranded wire. Twist on UL listed/CSA
approved wire connector. Gently tug on wires to be sure both are
secured.
17
Connect wires black to black and white to white, using UL
Listed/CSA Approved twist-on wire connectors (not included).
If needed, see website for animated representation of this step.
Visit www.whirlpool.com/electrical under FAQ tab.
Tighten strain relief screws to secure cable.
Place wires inside terminal box. Insert tabs on left side of cover.
Make sure wires are tucked inside box. Close cover ensuring
wires are not pinched. Use 1/4"nut driver and previously removed
screw to secure cover.
Check that dishwasher is still level front-to-back and side-to-side in
cabinet opening.
IMPORTANT: If you have solid countertops such as Corian% granite,
etc., you must use side mounting kit (Part Number 8212560). Follow
kit instructions. (Brackets included with kit.)
Open dishwasher door, remove lower dish rack, and place towel over
pump assembly and lower spray arm of dishwasher. This will keep
screws from falling into pump area when you are securing dishwasher
to countertop.
NOTE: Do not drop screws into bottom of dishwasher.
Locate brackets on top of dishwasher and secure dishwasher to
countertop with two, #10 x 1/2"Phillips-head screws (included). The
dishwasher must be secured to keep it from shifting when door is
opened.
1-®Corian is a registered trademark of E.I. Du Pont De Nemours and Company.
18
Check that top of door does not contact screws, brackets or
countertop. If it does, adjust leveling legs.
Open door and check that space between dishwasher cabinet
opening and tub is equal on both sides. If spacing is not equal,
loosen bracket screws secured and shift tub. Tighten bracket
screws.
Remove towel from dishwasher. Reinstall the lower dish rack.
If needed, see website for animated representation of this step.
Visit www.whirlpool.com/anchoring under FAQ tab.
lJ Reinstall_ccess panel and
Insul
(on some models
Place the plastic access panel against the dishwasher leg.
Check that the lower edge of the access panel touches the floor.
Adjust if necessary.
1
Using a flat-blade screwdriver, turn the fasteners /4 turn to lock
into place. The fastener's slot will be straight up and down when
properly locked.
19
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Plug intoa grounded 3 prong outlet. Check that power supply
cord does not touch dishwasher motor or lower part of
dishwasher tub.
Reconnect Power
Read the Dishwasher User Instructions that came with your
dishwasher.
Check that all parts have been installed and no steps were
skipped. Check that you have all tools used.
Start dishwasher and allow it to complete the shortest wash
cycle. After the first 2 minutes, unlatch door, wait 5 seconds,
then open door. Check that there is water in the bottom of the
dishwasher tub. Check that dishwasher is working properly.
If the dishwasher is not working properly, disconnect power or
unplug dishwasher and see "If Dishwasher Does Not Operate"
section.
First try the solutions suggested here to possibly avoid the cost of
a service call.
Has the circuit breaker tripped or the house fuse blown?
Is the door closed tightly and latched?
Has the cycle been set correctly to start the dishwasher?
Is the water turned on?
If none of these possible solutions work, call 1-800-253-1301, or
in Canada, call 1-800-807-6777.
Expect longer wash times. Your new dishwasher will average
2-3 hours per load, but use nearly 40% less energy than older
models. Designed with a low wattage, low energy consumption
motor, your dishwasher washes longer to ensure exceptional
cleaning. Certain models are equipped with an optical water
sensor so the first cycle will run longer to calibrate to optical
sensor. Selecting certain options could increase cycle time past
3.5 hours.
Rinse Aid is necessary for good drying results:
This dishwasher is designed to be used with rinse aid for good
drying performance and controlling hard water deposit buildup.
Energy efficient dishwashers use less water and energy, so they
depend on the water sheeting action of rinse aid for good drying
performance.
Start/Resume light may flash:
When pressing Start/Resume, you must make sure the door is
closed within 3 seconds. If you do not close the door within
3 seconds, the Start/Resume light will flash until you press it
again. (You must also do this when adding a dish during the
middle of a cycle.)
NOTE: If a braided supply hose is used, replace inlet hose after
5 years to reduce the risk of hose failure. Record hose installation
or replacement dates on the hose for future reference.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Magic Chef CDB7000AWB4 Guide d'installation

Catégorie
Lave-vaisselle
Taper
Guide d'installation
Ce manuel convient également à

dans d''autres langues