Generac 7117 Manuel utilisateur

Marque: Generac

Modèle: 7117

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

GP2200i Portable Generator

Owner’s Manual

SAVE THIS MANUAL FOR FUTURE REFERENCE

004472

(000209b)

WARNING

Loss of life. This product is not intended to

be used in a critical life support application.

Failure to adhere to this warning could result

in death or serious injury.

WWW.GENERAC.COM

1-888-GENERAC

(1-888-436-3722)

MODEL:________________________

SERIAL:________________________

DATE PURCHASED:______________

Table of Contents

Section 1 Introduction and Safety 1

Introduction ..................................... 1

Safety Rules .................................... 1

Safety Symbols and Meanings ........ 1

Exhaust and Location Hazards ....... 2

Electrical Hazards ........................... 3

Fire Hazards .................................... 3

Standards Index .............................. 3

Section 2 General Information and

Setup .............................................. 4

Know Your Generator ..................... 4

Emissions ........................................ 5

Connection Plugs ............................ 6

Off/Run/Choke Switch ..................... 6

USB Outlet ...................................... 6

Economy Switch .............................. 6

Generator Status Lights .................. 6

Circuit Protectors ............................. 6

Remove Contents from Carton ....... 7

Add Engine Oil ................................ 7

Fuel ................................................. 8

Section 3 Operation .......................9

Operation and Use Questions .........9

Before Starting Engine ....................9

Prepare Generator for Use ..............9

Grounding the Generator When In Use

Know Generator Limits ....................9

Transporting/Tipping of the Unit ....10

Starting Pull Start Engines .............10

Restarting Hot Engines ..................11

Low Oil Level Shutdown System ...11

Charging a 12 VDC Battery ...........11

Parallel Operation ..........................12

Section 4 Maintenance and

Troubleshooting ..........................13

Maintenance ..................................13

Maintenance Schedule ..................13

Preventive Maintenance ................13

Engine Maintenance ......................13

Storage ..........................................16

Troubleshooting .............................17

(000393)

WARNING

Operating, servicing and maintaining this

equipment can expose you to chemicals

including engine exhaust, carbon monoxide,

phthalates, and lead, which are known to the

State of California to cause cancer and birth

defects or other reproductive harm. To

minimize exposure, avoid breathing exhaust,

do not idle the engine except as necessary,

service your equipment in a well-ventilated

area and wear gloves or wash your hands

frequently when servicing your equipment.

For more information go to

www.P65Warnings.ca.gov.

Owner’s Manual for Portable Generator 1

Section 1 Introduction and Safety

Introduction

Thank you for purchasing a Generac Power

Systems Inc. product. This unit has been

designed to provide high-performance, effi-

cient operation, and years of use when main-

tained properly.

If any section of the manual is not understood,

contact your nearest Independent Authorized

Service Dealer (IASD), or contact Generac

Customer Service at 1-888-GENERAC (1-

888-436-3722), or www.generac.com with any

questions or concerns.

The owner is responsible for proper mainte-

nance and safe use of the equipment. Before

operating, servicing or storing this generator:

• Study all warnings in this manual and on

the product carefully.

• Become familiar with this manual and the

unit before use.

• Refer to the Assembly section of the man-

ual for instructions on final assembly proce-

dures. Follow the instructions completely.

Save these instructions for future reference.

ALWAYS supply this manual to any individual

that will use this machine.

The information in this manual is accurate

based on products produced at the time of

publication. The manufacturer reserves the

right to make technical updates, corrections,

and product revisions at any time without

notice.

Safety Rules

The manufacturer cannot anticipate every

possible circumstance that might involve a

hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, there-

fore, not all inclusive. If using a procedure,

work method or operating technique that the

manufacturer does not specifically recom-

mend, verify that it is safe for others. Also

make sure the procedure, work method or

operating technique utilized does not render

the equipment unsafe.

Throughout this publication, and on tags and

decals affixed to the generator, DANGER,

WARNING, CAUTION and NOTE blocks are

used to alert personnel to special instructions

about a particular operation that may be haz-

ardous if performed incorrectly or carelessly.

Observe them carefully. Their definitions are

as follows:

NOTE: Notes contain additional information

important to a procedure and will be found

within the regular text of this manual.

These safety warnings cannot eliminate the

hazards that they indicate. Common sense

and strict compliance with the special instruc-

tions while performing the action or service

are essential to preventing accidents.

Safety Symbols and Meanings

• If you start to feel sick, dizzy, or weak after

the generator has been running, move to

fresh air IMMEDIATELY. See a doctor, as

you could have carbon monoxide poison-

ing.

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

(000001)

DANGER

Indicates a hazardous situation which, if not avoided,

will result in death or serious injury.

(000002)

WARNING

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

(000003)

CAUTION

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

DANGER

Using a generator indoors CAN KILL YOU IN MINUTES.

Generator exhaust contains carbon monoxide. This is

a poison you cannot see or smell.

NEVER use inside a home

or garage, EVEN IF doors

and windows are open.

Only use OUTSIDE and

far away from windows,

doors, and vents.

000657

(000103)

DANGER

Asphyxiation. Running engines produce carbon

monoxide, a colorless, odorless, poisonous gas.

Carbon monoxide, if not avoided,

will result in death or serious injury.

2 Owner’s Manual for Portable Generator

• For safety reasons, it is recommended that

the maintenance of this equipment be per-

formed by an IASD. Inspect the generator

regularly, and contact the nearest IASD for

parts needing repair or replacement.

Exhaust and Location Hazards

• If you start to feel sick, dizzy, or weak after

the generator has been running, move to

fresh air IMMEDIATELY. See a doctor, as

you could have carbon monoxide poison-

ing.

• NEVER run a generator indoors or in a

partly enclosed area such as garages.

• ONLY use outdoors and far away from win-

dows, doors, vents, crawl spaces and in an

area where adequate ventilation is avail-

able and will not accumulate deadly

exhaust gas.

• Using a fan or opening a door will not pro-

vide sufficient ventilation.

• Point muffler exhaust away from people

and occupied buildings.

(000179b)

DANGER

Asphyxiation. The exhaust system must be properly

maintained. Do not alter or modify the exhaust system

as to render it unsafe or make it noncompliant with

local codes and/or standards. Failure to do so will

result in death or serious injury.

(000104)

DANGER

Electrocution. Water contact with a power source,

if not avoided, will result in death or serious injury.

(000116)

DANGER

Electrocution. Turn utility and emergency

power supplies to OFF before connecting power

source and load lines. Failure to do so will result

in death or serious injury.

(000146)

WARNING

Equipment and property damage. Do not alter

construction of, installation, or block ventilation for

generator. Failure to do so could result in unsafe

operation or damage to the generator.

(000178a)

Asphyxiation. Always use a battery operated carbon

monoxide alarm indoors and installed according to

the manufacturer’s instructions. Failure to do so

could result in death or serious injury.

WARNING

(000250)

WARNING

Equipment and property damage. Do not operate unit on

uneven surfaces, or areas of excessive moisture, dirt, dust

or corrosive vapors. Doing so could result in death, serious

injury, property and equipment damage.

(000111)

WARNING

Moving Parts. Keep clothing, hair, and appendages

away from moving parts. Failure to do so could

result in death or serious injury.

(000108)

WARNING

Hot Surfaces. When operting machine, do not

touch hot surfaces. Keep machine away from

combustables during use. Hot surfaces

could result in severe burns or fire.

(000142a)

Personal injury. Do not insert any object through the

air cooling slots. Generator can start at any time and

could result in death, serious injury, and unit damage.

WARNING

Risk of injury. Do not operate or service this machine

if not fully alert. Fatigue can impair the ability to service

this equipment and could result in death or serious

injury.

(000215)

WARNING

Injury and equipment damage. Do not use generator

as a step. Doing so could result in falling, damaged

parts, unsafe equipment operation, and could result

in death or serious injury.

(000216)

CAUTION

(000291)

Equipment damage. Do not attempt to start or operate

a unit in need of repair or scheduled maintenance.

Doing so could result in serious injury, death, or

equipment failure or damage.

WARNING

(000103)

DANGER

Asphyxiation. Running engines produce carbon

monoxide, a colorless, odorless, poisonous gas.

Carbon monoxide, if not avoided,

will result in death or serious injury.

(000179b)

DANGER

Asphyxiation. The exhaust system must be properly

maintained. Do not alter or modify the exhaust system

as to render it unsafe or make it noncompliant with

local codes and/or standards. Failure to do so will

result in death or serious injury.

(000146)

WARNING

Equipment and property damage. Do not alter

construction of, installation, or block ventilation for

generator. Failure to do so could result in unsafe

operation or damage to the generator.

(000178a)

Asphyxiation. Always use a battery operated carbon

monoxide alarm indoors and installed according to

the manufacturer’s instructions. Failure to do so

could result in death or serious injury.

WARNING

Owner’s Manual for Portable Generator 3

Electrical Hazards

• The National Electric Code (NEC) requires

the frame and external electrically conduc-

tive parts of the generator be properly con-

nected to an approved earth ground. Local

electrical codes may also require proper

grounding of the generator. Consult with a

local electrician for grounding requirements

in the area.

• Use a ground fault circuit interrupter in any

damp or highly conductive area (such as

metal decking or steel work).

• Once generator has been started outside,

connect electrical loads to extension

cord(s) inside.

Fire Hazards

• Allow at least 5 feet of clearance on all

sides of the generator when operating to

prevent overheating and fire.

• Do not operate the generator if connected

electrical devices overheat, if electrical out-

put is lost, if engine or generator sparks, or

if flames or smoke are observed while unit

is running.

• Keep a fire extinguisher near the generator

at all times.

Standards Index

1. National Fire Protection Association

(NFPA) 70: The NATIONAL ELECTRIC

CODE (NEC) available from www.nfpa.org

2. National Fire Protection Association

(NFPA) 5000: BUILDING CONSTRUC-

TION AND SAFETY CODE available from

www.nfpa.org

3. International Building Code available from

www.iccsafe.org

4. Agricultural Wiring Handbook available

from www.rerc.org, Rural Electricity

Resource Council P.O. Box 309 Wilming-

ton, OH 45177-0309

5. ASAE EP-364.2 Installation and Mainte-

nance of Farm Standby Electric Power

available from www.asabe.org, American

Society of Agricultural & Biological Engi-

neers 2950 Niles Road, St. Joseph, MI

49085

6. CSA C22.2 100-14 Electric motors and

generators for installation and use, in

accordance with the Rules of the Cana-

dian Electrical Code

7. ANSI/PGMA G300 Safety and Perfor-

mance of Portable Generators. Portable

Generator Manufacturer’s Association,

www.pgmaonline.com

This list is not all inclusive. Check with the

Authority Having Jurisdiction (AHJ) for any

local codes or standards which may be appli-

cable to your jurisdiction.

(000144)

DANGER

Electrocution. Contact with bare wires,

terminals, and connections while generator

is running will result in death or serious injury.

(000104)

DANGER

Electrocution. Water contact with a power source,

if not avoided, will result in death or serious injury.

(000145)

DANGER

Electrocution. In the event of electrical accident,

immediately shut power OFF. Use non-conductive

implements to free victim from live conductor. Apply

first aid and get medical help. Failure to do so will

result in death or serious injury.

(000105)

DANGER

Explosion and Fire. Fuel and vapors are extremely

flammable and explosive. Add fuel in a well

ventilated area. Keep fire and spark away. Failure to

do so will result in death or serious injury.

(000166b)

DANGER

Explosion and Fire. Do not overfill fuel tank. Fill to

1/2 inch from top of tank to allow for fuel expansion.

Overfilling may cause fuel to spill onto engine causing

fire or explosion, which will result in death or

serious injury.

(000142a)

Personal injury. Do not insert any object through the

air cooling slots. Generator can start at any time and

could result in death, serious injury, and unit damage.

WARNING

Fire risk. Fuel and vapors are extremely

flammable. Do not operate indoors. Doing so

could result in death, serious injury, or

property or equipment damage.

(000281)

WARNING

Explosion and fire risk. Do not smoke near unit.

Keep fire and spark away. Failure to do so could

result in death, serious injury, or property or

equipment damage.

(000282)

WARNING

Explosion and Fire. Do not smoke while

refueling unit. Failure to do so could result in

death, serious injury, or property or equipment

damage.

(000284a)

4 Owner’s Manual for Portable Generator

Section 2 General Information and Setup

Figure 2-1. Features and Controls

TABLE 1. Generator Components

Figure 2-2. Control Panel

Know Your Generator

Replacement owner’s manuals are available

at www.generac.com.

002320

004707

1 Off/Run/Choke Switch

2 Economy Switch

3 120V, 20A Receptacle

4 Circuit Protector (if equipped)

5 Parallel Outlets

6 Grounding Location

7 1.5A, 5VDC USB Outlet

8 DC Receptacle (battery charger)

9Low Oil Warning

10 Overload Warning

11 AC Power Light

12 Carrying Handle

13 Fuel Tank Vent

14 Fuel Cap

15 Recoil Starter

16 Spark Arrestor

17 Muffler Cover

18 Service Door

19 Spark Plug Cover

004468

10 11

5 6

(000100a)

WARNING

Consult Manual. Read and understand manual

completely before using product. Failure to

completely understand manual and product

could result in death or serious injury.

Owner’s Manual for Portable Generator 5

Emissions

The United States Environmental Protection

Agency (US EPA) (and California Air

Resources Board (CARB), for engines/equip-

ment certified to California standards) requires

that this engine/equipment complies with

exhaust and evaporative emissions stan-

dards. Locate the emissions compliance decal

on the engine to determine applicable stan-

dards. For emissions warranty information,

please reference the included emissions war-

ranty. It is important to follow the maintenance

specifications in the manual to ensure that the

engine complies with the applicable emissions

standards for the duration of the product’s life.

TABLE 2. Product Specifications

Generator Specifications 2200i

Rated Power 1700 W

Starting Power 2200 W

Rated AC Voltage 120V

Rated AC Load at 120V 14.1 Amps**

Rated Frequency 60 Hz

Dimensions L x W x H (in/mm) 19.8 x 11.5 x 17.9 (504 x 293 x 454)

Weight (dry) 48 lb. (21.8 kg)

** Operating Temperature Range: -13 deg. C (8 deg. F) to 40 Deg. C (104 Deg. F). When operated

above 25 deg. C (77 deg. F) there may be a decrease in power.

** Maximum wattage and current are subject to, and limited by, such factors as fuel Btu content,

ambient temperature, altitude, engine condition, etc.. Maximum power decreases about 3.5% for

each 1,000 feet above sea level; and will also decrease about 1% for each 6° C (10° F) above 16°

C (60° F) ambient temperature.

Engine Specifications 2200i

Engine Type Single Cylinder, 4-stroke

Displacement 80 cc

Spark Plug Part Number 0K95530157

Spark Plug Type E6TC / E6RTC / BPR6HS or equivalent

Spark Plug Gap (in/mm) 0.024-0.028 (0.6-0.7)

Fuel Capacity / Type 4.5 L (1.18 U.S. gallons) / Unleaded

Oil Type

See

Add Engine Oil

Oil Capacity 0.35 L (0.36 qt.)

Run Time at 50% Load 7.0 Hours

* Go to www.generac.com or contact an IASD for replacement parts.

6 Owner’s Manual for Portable Generator

Connection Plugs

120 VAC, Duplex Receptacle

The 120 Volt outlet is overload protected by

the 15 Amp push button circuit protector. See

Figure 2-3. Each receptacle will power 120

Volt AC, single phase, 60 Hz electrical loads

requiring up to 1700 watts (1.7 kW).

Figure 2-3. 120 VAC, Duplex Receptacle

Off/Run/Choke Switch

This controls the ON/OFF functions, choke

and fuel valve operation. See Figure 2-4.

• The OFF position (1) stops the engine and

shuts off fuel flow.

• The RUN position (2) is for normal opera-

tion and to gradually reduce the use of the

choke.

• The CHOKE position (3) switches the fuel

valve on to start the engine.

NOTE: The CHOKE is not required to start a

warm engine.

Figure 2-4. Dial (example)

USB Outlet

The 5 VDC, 1.5 Amp USB outlet allows

charging of compatible electronic devices.

Economy Switch

The economy switch has 2 modes of opera-

tion:

• On: The quietest mode and best when run-

ning appliances or equipment that are

resistive loads (non-motor starting), (exam-

ple: TV, video game, light, radio).

• Off: Best when running a both inductive

(motor-starting loads) and resistive (non-

motor starting loads), especially when

these loads are turning on and off (exam-

ple: RV, air conditioner, hairdryer).

Generator Status Lights

See Figure 2-5.

• Overload LED (orange): Indicates system

overload (2). During motor starting it is nor-

mal for the overload LED to illuminate for a

few seconds. If LED stays illuminated and

the ready LED turns off, the engine will con-

tinue to run without output power. Remove

all applied loads and determine if attached

devices exceed recommended output

power. Check for faulty or shorted connec-

tions. To restore electrical output, turn dial

OFF to reset. Start engine. If condition was

corrected, the orange LED will not illumi-

nate and electrical output will be restored.

Loads can be applied once the green LED

illuminates. If the orange LED returns, con-

tact an IASD.

• Low Oil Level LED (red): Illuminates when

oil level is below safe operating level.

Engine shuts down (1).

• Power LED (green): Indicates output from

generator (3) (unless there is a low oil or

overload condition).

Figure 2-5. Status Indicators

Circuit Protectors

The AC receptacles are protected by an AC

circuit protector. The DC receptacles are pro-

tected by a DC circuit protector. If the genera-

tor is overloaded or an external short circuit

occurs, the circuit protector will trip. If this

occurs, disconnect all electrical loads to deter-

mine the cause of the problem before using

the generator again. Reduce the load if the cir-

cuit protector is tripped.

000424

002347

002335

1 2 3

Owner’s Manual for Portable Generator 7

NOTE: Continuous tripping of the circuit pro-

tector may cause damage to generator or

equipment.

Push the button of the protector to reset the

circuit protector.

Remove Contents from Carton

1. Open carton completely by cutting each

corner from top to bottom.

2. Remove and verify carton contents prior to

assembly. Carton contents should contain

the following:

TABLE 3. Accessories

3. Call Generac Customer Service at 1-888-

GENERAC (1-888-436-3722) with the unit

model and serial number for any missing

carton contents.

4. Record model, serial number, and date of

purchase on front cover of this manual.

Add Engine Oil

NOTE: The generator is shipped without oil in

the engine. Add oil slowly and verify oil level

often during filling process to ensure overfilling

does not occur.

1. Place generator on a level surface.

2. Remove screws and side cover. See Fig-

ure 2-6.

Figure 2-6. Remove Side Cover

3. Clean area around oil fill and oil drain plug.

4. Remove oil fill cap and wipe dipstick clean.

See Figure 2-7.

Figure 2-7. Remove Dipstick

5. Insert funnel into oil fill opening. Add rec-

ommended engine oil as necessary. Cli-

mate determines proper engine oil

viscosity. See chart to select correct vis-

cosity.

NOTE: Use petroleum based oil (supplied) for

engine break-in before using synthetic oil.

6. To check oil level, remove funnel and

insert dipstick into oil filler neck. See Fig-

ure 2-8.

Item Qty.

Main Unit 1

Owner’s Manual 1

Engine Oil 1

Oil Funnel 1

DC Charging Cable 1

Tool Kit 1

Product Registration Card 3

Service Warranty 1

Emissions Warranty 1

(000135)

CAUTION

Engine damage. Verify proper type and quantity of

engine oil prior to starting engine. Failure to do so

could result in engine damage.

002542

002404

SAE 30

10W-30

Synthetic 5W-30

000399

8 Owner’s Manual for Portable Generator

Figure 2-8. Safe Operating Range

7. Remove dipstick and verify oil level is

within safe operating range.

NOTE: Verify oil level often during filling pro-

cess to ensure overfilling does not occur.

8. Install oil fill cap/dipstick and hand-tighten.

9. Replace side cover and screws.

Fuel

Fuel requirements are as follows:

• Clean, fresh, unleaded gasoline.

• Minimum rating of 87 octane/87 AKI (91

RON).

• Up to 10% ethanol (gasohol) is acceptable.

• DO NOT use E85.

• DO NOT use a gas oil mix.

• DO NOT modify engine to run on alternate

fuels. Stabilize fuel prior to storage.

1. Verify unit is OFF and cooled entirely prior

to fueling.

2. Place unit on level ground in a well venti-

lated area.

3. Clean area around fuel cap and turn vent

on fuel cap to ON. See Figure 2-9.

Figure 2-9.Fuel Cap

4. Turn cap slowly to remove.

5. Slowly add recommended fuel. Do not

overfill.

NOTE: Fill to red insert inside filler neck. See

Figure 2-10.

6. Install fuel cap.

7. Turn vent on fuel cap to OFF for transpor-

tation and storage to avoid fuel spills.

Figure 2-10. Internal Fuel Tank Level

NOTE: Allow spilled fuel to evaporate before

starting unit.

IMPORTANT NOTE: It is important to pre-

vent gum deposits from forming in fuel

system parts such as the carburetor, fuel

hose or tank during storage. Alcohol-

blended fuels (called gasohol, ethanol or

methanol) can attract moisture, which

leads to separation and formation of acids

during storage. Acidic gas can damage the

fuel system of an engine while in storage.

To avoid engine problems, the fuel system

should be emptied before storage of 30

days or longer. See the Storage section.

Never use engine or carburetor cleaner

products in the fuel tank as permanent

damage may occur.

001792

(000105)

DANGER

Explosion and Fire. Fuel and vapors are

extremely flammable and explosive. Add fuel

in a well ventilated area. Keep fire and spark

away. Failure to do so will result in death

or serious injury.

(000166b)

DANGER

Explosion and Fire. Do not overfill fuel tank. Fill to

1/2 inch from top of tank to allow for fuel expansion.

Overfilling may cause fuel to spill onto engine causing

fire or explosion, which will result in death or

serious injury.

(000362)

Explosion and Fire. Verify fuel cap vent is set to

ON for operation, and OFF for transportation and

storage. Failure to do so could result in poor unit

performance, death, or serious injury.

WARNING

001112

002543

Owner’s Manual for Portable Generator 9

Section 3 Operation

Operation and Use Questions

Call Generac Customer Service at 1-888-

GENERAC (1-888-436-3722) with questions

or concerns about equipment operation and

maintenance.

Before Starting Engine

1. Verify engine oil level is correct.

2. Verify fuel level is correct.

3. Verify unit is secure on level ground, with

proper clearance and is in a well ventilated

area.

Prepare Generator for Use

Grounding the Generator When

In Use

The generator is equipped with an equipment

ground connecting the generator frame and

the ground terminals on the AC output recep-

tacles (see NEC 250.34 (A). This allows the

generator to be used as a portable without

grounding the frame of the generator as spec-

ified in NEC 250.34. See Figure 3-1.

• Neutral Floating

Figure 3-1.Grounding the Generator

The generator (stator winding) is isolated from

the frame and from the AC receptacle ground

pin. Electrical devices that require a grounded

receptacle pin connection will not function if

the receptacle ground pin is not functional.

Know Generator Limits

Overloading a generator can result in damage

to the generator and connected electrical

devices. Observe the following to prevent

overload:

• Add up the total wattage of all electrical

devices to be connected at one time. This

total should NOT be greater than the gener-

ator's wattage capacity.

• The rated wattage of lights can be taken

from light bulbs. The rated wattage of tools,

appliances, and motors can be found on a

data label or decal affixed to the device.

• If the appliance, tool, or motor does not

give wattage, multiply volts times ampere

rating to determine watts (volts x amps =

watts).

• Some electric motors, such as induction

types, require about three times more watts

of power for starting than for running. This

surge of power lasts only a few seconds

when starting such motors. Make sure to

allow for high starting wattage when select-

ing electrical devices to connect to the gen-

erator:

1. Figure the watts needed to start the largest

motor.

2. Add to that figure the running watts of all

other connected loads.

Asphyxiation. Running engines produce

carbon monoxide, a colorless, odorless,

poisonous gas. Carbon monoxide, if not

avoided, will result in death or serious injury.

(000103)

DANGER

(000179b)

DANGER

Asphyxiation. The exhaust system must be properly

maintained. Do not alter or modify the exhaust system

as to render it unsafe or make it noncompliant with

local codes and/or standards. Failure to do so will

result in death or serious injury.

WARNING

(000118a)

Risk of fire. Do not use generator without

spark arrestor installed. Failure to do so

could result in death or serious injury.

(000178a)

Asphyxiation. Always use a battery operated carbon

monoxide alarm indoors and installed according to

the manufacturer’s instructions. Failure to do so could

result in death or serious injury.

WARNING

(000110)

WARNING

Risk of Fire. Hot surfaces could ignite

combustibles, resulting in fire. Fire could

result in death or serious injury.

(000108)

WARNING

Hot Surfaces. When operating machine, do not

touch hot surfaces. Keep machine away from

combustibles during use. Hot surfaces could

result in severe burns or fire.

(000136)

CAUTION

Equipment and property damage. Disconnect electrical

loads prior to starting or stopping unit. Failure to do so

could result in equipment and property damage.

004468

10 Owner’s Manual for Portable Generator

Wattage Reference Guide is provided to assist

in determining how many items the generator

can operate at one time.

NOTE: All figures are approximate. See data

label on appliance for wattage requirements.

Wattage Reference Guide

Transporting/Tipping of the Unit

Do not store or transport the unit at an angle

greater than 15 degrees.

Starting Pull Start Engines

1. Turn fuel cap vent ON. See Figure 2-9.

2. See Figure 3-2. Rotate the Off/Run/Choke

dial to CHOKE (1).

3. Switch Economy switch to OFF.

4. Firmly grasp recoil handle and pull slowly

until increased resistance is felt. Pull rap-

idly up and away.

Figure 3-2.Off/Run/Choke Positions

Device Running

Watts

*Air Conditioner (12,000 Btu) 1700

*Air Conditioner (24,000 Btu) 3800

*Air Conditioner (40,000 Btu) 6000

Battery Charger (20 Amp) 500

Belt Sander (3") 1000

Chain Saw 1200

Circular Saw (6-1/2") 800 to 1000

*Clothes Dryer (Electric) 5750

*Clothes Dryer (Gas) 700

*Clothes Washer 1150

Coffee Maker 1750

*Compressor (1 HP) 2000

*Compressor (3/4 HP) 1800

*Compressor (1/2 HP) 1400

Curling Iron 700

*Dehumidifier 650

Disc Sander (9") 1200

Edge Trimmer 500

Electric Blanket 400

Electric Nail Gun 1200

Electric Range (per element) 1500

Electric Skillet 1250

*Freezer 700

*Furnace Fan (3/5 HP) 875

*Garage Door Opener 500 to 750

Hair Dryer 1200

Hand Drill 250 to 1100

Hedge Trimmer 450

Impact Wrench 500

Iron 1200

*Jet Pump 800

Lawn Mower 1200

Light Bulb 100

Microwave Oven 700 to 1000

*Milk Cooler 1100

Oil Burner on Furnace 300

Oil Fired Space Heater (140,000

Btu)

400

Oil Fired Space Heater (85,000 Btu) 225

Oil Fired Space Heater (30,000 Btu) 150

*Paint Sprayer, Airless (1/3 HP) 600

Paint Sprayer, Airless (hand-held) 150

Radio 50 to 200

*Refrigerator 700

Slow Cooker 200

*Submersible Pump (1-1/2 HP) 2800

*Submersible Pump (1 HP) 2000

*Submersible Pump (1/2 HP) 1500

*Sump Pump 800 to 1050

*Table Saw (10") 1750 to 2000

Television 200 to 500

Toaster 1000 to 1650

Weed Trimmer 500

* Allow 3 times the listed watts for starting these

devices.

(000183)

WARNING

Recoil Hazard. Recoil could retract unexpectedly.

Kickback could result in death or serious injury.

(000136)

CAUTION

Equipment and property damage. Disconnect electrical

loads prior to starting or stopping unit. Failure to do so

could result in equipment and property damage.

002347

Owner’s Manual for Portable Generator 11

5. See Figure 3-2. When engine starts, rotate

Off/Run/Choke dial to RUN (2). Choke

operation is reduced as Off/Run/Choke

dial is rotated towards RUN.

NOTE: If engine fires, but does not continue to

run, rotate the Off/Run/Choke dial to OFF and

repeat starting instructions.

IMPORTANT NOTE: Do not overload gener-

ator or individual panel receptacles. See

Figure 3-3. If an overload occurs, the over-

load LED (A) will illuminate and AC output

ceases. To correct, see Generator Status

Lights. Read Know Generator Limits care-

fully.

Figure 3-3.Shutdown Fault

Generator Shut Down

1. Shut off all loads and unplug electrical

loads from generator panel receptacles.

2. Let engine run at no-load for several min-

utes to stabilize internal temperatures of

engine and generator.

3. See Figure 3-2 Rotate Off/Run/Choke dial

to OFF (3).

4. Turn fuel cap OFF.

Restarting Hot Engines

1. See Figure 3-2. Turn Off/Run/Choke dial

from STOP to RUN. This will open the fuel

valve and permit starting.

2. Firmly grasp recoil handle and pull slowly

until increased resistance is felt. Pull rap-

idly up and away.

Low Oil Level Shutdown System

The engine is equipped with a low oil level

sensor that shuts down the engine automati-

cally when the oil level drops below a speci-

fied level to prevent engine damage. See

Figure 3-3 (B). The engine will not run until the

oil has been filled to the proper level.

If the engine shuts down and there is sufficient

fuel, check engine oil level.

Charging a 12 VDC Battery

NOTE: A battery may lose some of its charge

when not in use for prolonged periods of time.

The DC charging output is not regulated. The

circuit protector does not prevent over

charging a battery. Battery charging should be

done in a dry location.

1. Start generator and turn Economy switch

OFF.

2. Plug Battery Charging Cable into Battery

Charger Output jack, located on the con-

trol panel. See Figure 3-4.

3. Connect positive (+) battery clamp (red

wire) to battery FIRST.

4. Connect negative (-) battery clamp (black

wire) to battery SECOND.

NOTE: This receptacle can not recharge 6-

volt batteries and can not be used to crank an

engine having a discharged battery.

Figure 3-4. Battery Charger Input Jack

002335

(000136)

CAUTION

Equipment and property damage. Disconnect electrical

loads prior to starting or stopping unit. Failure to do so

could result in equipment and property damage.

(000136)

CAUTION

Equipment and property damage. Disconnect electrical

loads prior to starting or stopping unit. Failure to do so

could result in equipment and property damage.

(000137a)

WARNING

Explosion. Batteries emit explosive gases while charging.

Keep fire and spark away. Wear protective gear when

working with batteries. Failure to do so could result in

death or serious injury.

(000138a)

WARNING

004469

WARNING

Environmental Hazard. Always recycle batteries at an

official recycling center in accordance with all local

laws and regulations. Failure to do so could result in

environmental damage, death or serious injury.

(000228)

12 Owner’s Manual for Portable Generator

Parallel Operation

For output power up to 3230W, two inverters

can operate in parallel using Generac’s Paral-

lel Kit (optional). See the Parallel Kit Opera-

tor’s Manual or contact an IASD.

NOTE: All connections to the parallel kit

should be made while both inverters are

turned off and all loads disconnected.

1. Make sure the Engine Economy Switch is

in the same position on both generators.

2. Make appropriate parallel connections to

the outlets on each Generac inverter as

outlined in the owner’s manual supplied

with the kit.

NOTE: Do not disconnect any parallel kit con-

nections once the units are running.

3. Start both units per starting instructions.

Once the green output indicator illumi-

nates, devices can be connected and

turned on using the parallel kit outlet.

4. Follow Generator Shut Down instructions.

NOTE: For inverters, load applied to the paral-

lel kit is not to exceed 3230 watts due to a 5%

power loss when paralleling. See manual.

NOTE: Only use Generac approved parallel

kit.

Owner’s Manual for Portable Generator 13

Section 4 Maintenance and Troubleshooting

Maintenance

Regular maintenance will improve perfor-

mance and extend engine/equipment life.

Generac Power Systems, Inc. recommends

that all maintenance work be performed by an

Independent Authorized Service Dealer

(IASD). Regular maintenance, replacement,

or repair of the emissions control devices and

systems may be performed by any repair shop

or person of the owner’s choosing. To obtain

emissions control warranty service free of

charge, the work must be performed by an

IASD. See the emissions warranty.

NOTE: Call 1-888-GENERAC (1-888-436-

3722) with questions about component

replacement.

Maintenance Schedule

Follow maintenance schedule intervals,

whichever occurs first according to use.

NOTE: Adverse conditions will require more

frequent service.

NOTE: All required service and adjustments

should be each season as detailed in the fol-

lowing chart.

Preventive Maintenance

Dirt or debris can cause improper operation

and equipment damage. Clean generator

daily or before each use. Keep area around

and behind muffler free from combustible

debris. Inspect all cooling air openings on

generator.

• Use a damp cloth to wipe exterior surfaces

clean.

• Use a soft bristle brush to loosen caked on

dirt, oil, etc.

• Use a vacuum to pick up loose dirt and

debris.

• Low pressure air (not to exceed 25 psi)

may be used to blow away dirt. Inspect

cooling air slots and openings on generator.

These openings must be kept clean and

unobstructed.

NOTE: DO NOT use a garden hose to clean

generator. Water can enter engine fuel system

and cause problems. If water enters generator

through cooling air slots, some water will be

retained in voids and crevices of rotor and sta-

tor winding insulation. Water and dirt buildup

on generator internal windings will decrease

insulation resistance of windings.

Engine Maintenance

Engine Oil Recommendations

To maintain the product warranty, the engine

oil should be serviced in accordance with the

recommendations of this manual. For your

convenience, maintenance kits designed and

intended for use on this product are available

from the manufacturer that include engine oil,

oil filter, air filter, spark plug(s), a shop towel

and funnel. These kits can be obtained from

an Independent Authorized Service Dealer

(IASD).

At Each Use

Check engine oil level

Every 50 Hours

Clean/Replace Air Filter**

Change oil ǂ

Every 100 Hours or Every Season*

Replace Spark Plug

Clean Spark Arrestor

Valve Clearance Adjustment

Every 200 Hours or Every Season

Inspect/clean air cleaner filter**

Replace Fuel Filter +

ǂ Change oil after first 30 hours of operation,

then every 50 hours.

+ To be performed by IASD.

* Change oil every month when operating

under heavy load or in high temperatures.

** Clean more often under dirty or dusty oper-

ating conditions. Replace air filter parts if

they cannot be adequately cleaned.

*** Check valve clearance and adjust if neces-

sary after first 50 hours of operation and

every 100 hours thereafter.

(000142a)

Personal injury. Do not insert any object through the

air cooling slots. Generator can start at any time and

could result in death, serious injury, and unit damage.

WARNING

(000141)

WARNING

Accidental start-up. Disconnect spark plug wires when

working on unit. Failure to do so could result in death

or serious injury.

14 Owner’s Manual for Portable Generator

Inspect Engine Oil Level

Inspect engine oil level prior to each use, or

every 8 hours of operation.

1. Place generator on a level surface.

2. Clean area around oil fill, and oil drain

plug.

3. Remove oil fill cap and wipe dipstick clean.

See Figure 4-1.

Figure 4-1. Engine Oil Fill

4. To check oil level, insert dipstick into oil

filler neck without screwing it in. See Fig-

ure 4-2.

Figure 4-2. Safe Operating Range

5. Remove dipstick and verify oil level is

within safe operating range.

6. Add recommended engine oil as neces-

sary.

NOTE: Verify oil level often during filling pro-

cess to ensure overfilling does not occur.

7. Replace oil fill cap and hand-tighten.

NOTE: Some units have more than one oil fill

location. It is only necessary to use one oil fill

point.

Change Engine Oil

When using generator under extreme, dirty,

dusty conditions, or in extremely hot weather,

change oil more frequently.

NOTE: Don’t pollute. Conserve resources.

Return used oil to collection centers.

Change oil while engine is still warm from run-

ning, as follows:

1. Place generator on a level surface.

2. Remove screws and side cover. See Fig-

ure 4-3.

Figure 4-3. Remove Side Cover

3. Disconnect the spark plug wire from the

spark plug and place the wire where it

cannot contact spark plug.

4. Clean area around oil fill and oil drain plug.

5. Remove oil fill cap and wipe dipstick clean.

6. Tip unit and drain oil completely into a suit-

able container.

7. Once oil is sufficiently drained from unit, tip

unit back to a level position.

8. Insert funnel into oil fill opening. See Fig-

ure 4-4. Add recommended engine oil as

necessary.

Figure 4-4. Oil Fill Opening With Funnel

SAE 30

10W-30

Synthetic 5W-30

000399

(000139)

WARNING

Risk of burns. Allow engine to cool before

draining oil or coolant. Failure to do so could

result in death or serious injury.

002404

001792

(000141)

WARNING

Accidental start-up. Disconnect spark plug wires when

working on unit. Failure to do so could result in death

or serious injury.

002542

002350

Owner’s Manual for Portable Generator 15

9. To check oil level, remove funnel and

insert dipstick into oil filler neck without

screwing it in. See Figure 4-2.

10. Remove dipstick and verify oil level is

within safe operating range.

NOTE: Verify oil level often during filling pro-

cess to ensure overfilling does not occur.

11. Replace oil fill cap and hand-tighten.

12. Wipe up any spilled oil.

13. Replace side cover and screws.

14. Properly dispose of oil in accordance with

all applicable regulations.

Air Filter

Engine will not run properly and may be dam-

aged if run with a dirty air filter. Service air fil-

ter more frequently in dirty or dusty conditions.

To service air filter:

1. Remove screws and side cover. See Fig-

ure 4-3.

2. Unscrew bolt (A) and remove air filter

cover. See Figure 4-5.

3. Wash filter (B) in soapy water. Squeeze

dry in clean cloth (DO NOT TWIST).

4. Clean air filter cover before installation.

5. Replace side cover and screws.

NOTE: To order a new air filter, contact the

nearest authorized service center at 1-888-

436-3722.

Figure 4-5. Air Filter Assembly

Service Spark Plug

To service spark plug:

1. Remove spark plug cover. See Figure 2-1.

2. Clean area around spark plug.

3. Remove and inspect spark plug.

4. Inspect electrode gap with wire feeler

gauge and reset spark plug gap to 0.6 -

0.7mm (0.024 - 0.028 in). See Figure 4-6.

Figure 4-6. Spark Plug

NOTE: Replace spark plug if electrodes are

pitted, burned or porcelain is cracked. Use

ONLY recommended replacement plug. See

Product Specifications.

5. Install spark plug finger tight, and tighten

an additional 3/8 to 1/2 turn using spark

plug wrench.

Inspect Muffler and Spark Arrester

NOTE: It is a violation of California Public

Resource Code, Section 4442, to use or oper-

ate the engine on any forest-covered, brush-

covered, or grass-covered land unless the

exhaust system is equipped with a spark

arrester, as defined in Section 4442, main-

tained in effective working order. Other states

or federal jurisdictions may have similar laws.

Contact original equipment manufacturer,

retailer, or dealer to obtain a spark arrester

designed for exhaust system installed on this

engine.

NOTE: Use ONLY original equipment replace-

ment parts.

Inspect muffler for cracks, corrosion, or other

damage. Remove spark arrester, if equipped,

inspect for damage or carbon blockage.

Replace parts as required.

Inspect Spark Arrester Screen

Clean Spark Arrestor Screen

The engine exhaust muffler has a spark arres-

tor screen. Inspect and clean the screen every

100 hours of operation or every season,

whichever comes first.

To service spark arrestor:

1. See Figure 4-7. Remove the clamp to

remove retainer.

2. Slide spark arrestor screens out from the

muffler outlet tube.

3. Inspect screens and replace if torn, perfo-

rated or otherwise damaged. Do NOT use

a defective screen. If screen is not dam-

aged, clean with a commercial solvent.

002351

000211

(000108)

WARNING

Hot Surfaces. When operating machine, do not

touch hot surfaces. Keep machine away from

combustibles during use. Hot surfaces could

result in severe burns or fire.

16 Owner’s Manual for Portable Generator

4. Replace the screens, and retainer, and

secure with clamp.

Figure 4-7. Spark Arrestor Screen

Valve Clearance

Important: Please contact an Independent

Authorized Service Dealer for service assis-

tance. Proper valve clearance is essential for

prolonging the life of the engine.

Check valve clearance after the first fifty-hours

of operation. Adjust as necessary.

• Intake — 0.10 ± 0.02mm (cold), (0.004" ±

0.001" inches)

• Exhaust — 0.10 ± 0.02mm (cold) (0.004" ±

0.001" inches)

Storage

General

It is recommended to start and run the genera-

tor for 30 minutes, every 30 days. If this is not

possible, refer to the following list to prepare

unit for storage.

• DO NOT place a storage cover on a hot

generator. Allow unit to cool to room tem-

perature before storage.

• DO NOT store fuel from one season to

another unless properly treated.

• Replace fuel container if rust is present.

Rust in fuel will cause fuel system prob-

lems.

• Cover unit with a suitable protective, mois-

ture resistant cover.

• Store unit in a clean, dry area.

• Always store generator and fuel away from

heat and ignition sources.

Prepare Fuel System/Engine for

Storage

Fuel stored over 30 days can go bad and

damage fuel system components. Keep fuel

fresh, use fuel stabilizer.

If fuel stabilizer is added to fuel system, pre-

pare and run engine for long term storage.

Run engine for 10-15 minutes to circulate sta-

bilizer throughout fuel system. Adequately

prepared fuel can be stored up to 24 months.

NOTE: If fuel has not been treated with fuel

stabilizer, it must be drained into an approved

container. Run engine until it stops from lack

of fuel. Use of fuel stabilizer in fuel storage

container is recommended to keep fuel fresh.

1. Change engine oil.

2. Remove spark plug.

3. Pour tablespoon (5-10cc) of clean engine

oil or spray a suitable fogging agent into

cylinder.

4. Pull starter recoil several times to distrib-

ute oil in cylinder.

5. Install spark plug.

6. Pull recoil slowly until resistance is felt.

This will close valves so moisture cannot

enter engine cylinder. Gently release

recoil.

Change Oil

Change engine oil before storage. See,

Change Engine Oil.

002352

(000143)

DANGER

Explosion and Fire. Fuel and vapors are extremely

flammable and explosive. Store fuel in a well

ventilated area. Keep fire and spark away. Failure

to do so will result in death or serious injury.

(000109)

WARNING

Risk of Fire. Verify machine has properly

cooled before installing cover and storing

machine. Hot surfaces could result in fire.

(000181)

WARNING

Vision Loss. Eye protection is required to avoid

spray from spark plug hole when cranking engine.

Failure to do so could result in vision loss.

Owner’s Manual for Portable Generator 17

Troubleshooting

PROBLEM CAUSE CORRECTION

Engine won't start. 1. Dial turned off.

2. Out of fuel.

3. Defective spark plug.

4. Plugged fuel filter.

5. Defective or stuck Dial assem-

bly.

6. Incorrect engine oil level.

7. Defective ignition coil.

8. Fuel cap vent OFF.

9. Carb is flooded.

10. Throttle plate closed.

1. Turn on Dial.

2. Fill fuel tank.

3. Replace spark plug.

4. Replace fuel and fuel filter.

5. Contact IASD.

6. Check/fill engine oil.

7. Contact IASD.

8. Turn fuel cap vent ON.

9. Drain carb.

10. Open throttle plate (push

toward back of unit).

Engine starts, then shuts

down.

1. Out of fuel.

2. Incorrect engine oil level.

3. Contaminated fuel.

4. Defective low oil level switch.

5. Fuel cap vent OFF.

1. Fill fuel tank.

2. Check engine oil level.

3. Contact IASD.

4. Contact IASD.

5. Turn fuel cap vent ON.

Engine will not start; or

starts and runs rough.*

1. Choke is stuck or left on.

2. Dirty or clogged air filter.

3. Defective or dirty spark plug.

4. Dirty fuel filter.

5. Dirty or gummed up carburet-

tor.

6. Unit not warmed up.

7. Fuel cap vent OFF.

8. Spark arrestor clogged.

1. Turn choke off.

2. Clean or replace air filter.

3. Replace spark plug.

4. Replace fuel and fuel filter.

5. Clean carburetor.

6. Gradually adjust Dial and

reduce choke until engine runs

smoothly in RUN position.

7. Turn fuel cap vent ON.

8. Clean spark arrestor.

No AC output. 1. Generator is overloaded.

2. Inverter module is overheated.

3. Short circuit in electrical

device.

4. Defective inverter assembly.

1. Disconnect all loads. Shut

down generator to reset mod-

ule. Reduce loads, restart

generator.

2. Verify service door is ON. Let

cool 15 minutes by running

engine without AC output.

Press and hold Reset button

on control panel, restart gener-

ator.

3. Verify condition of extension

cords and items being pow-

ered. Press and hold Reset

button on control panel.

4. Contact IASD.

Fuel leaks from drain

hoses.

1. Carburetor drain in bowl is not

closed.

1. Turn valve clockwise to close.

* Engine speed increases and decreases — This is normal as generator starts up and loads vary.

Part No. 10000010470 Rev. C 04/02/2018

Specifications are subject to change without notice.

No reproduction allowed in any form without prior

written consent from Generac Power Systems, Inc.

Generac Power Systems, Inc.

S45 W29290 Hwy. 59

Waukesha, WI 53189

1-888-GENERAC (1-888-436-3722)

www.generac.com

La page charge ...

Generac 7117 Manuel utilisateur

Marque: Generac

Modèle: 7117

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Generac 7117 User manual
español: Generac 7117 Manual de usuario

Generac 7117 Manuel utilisateur

Generac 7117 Manuel utilisateur

dans d''autres langues

Documents connexes