Generac 17 kW 0056130 Manuel utilisateur

INSTALLATION

GUIDELINES

Air-cooled Generators

TABLE OF CONTENTS

Introduction ..................................................Inside Front Cover

General Hazards ................................................................... IFC

Generator Installation ............................................................... 1

Before Installation ...................................................................... 1

NFPA Standards ......................................................................... 1

Other Published Standards ....................................................... 1

Grounding the Generator .......................................................... 2

Battery Installation ....................................................................2

Vented Batteries ......................................................................... 2

Before You Begin ........................................................................2

Site Preparation and Generator Placement .............................2

Coverting to LP Vapor ............................................................... 3

Installing & Connecting Gas Lines .......................................... 4

Battery Charger Installation ..................................................... 5

External Electrical Connections ............................................... 6

Generator Connections - RTS Load Center

Transfer Switch ....................................................................... 6

Appendix A - RTS Pre-wired Load Center Transfer

Switch Installation & Operational Testing ........................... 8

Battery Installation .................................................................. 9

Operational Testing ............................................................... 10

Appendix B - RTSN Nd RTSE Transfer Switch

Installation & Operational Testing ...................................... 12

Selected Circuit Coverage ..................................................... 12

Whole-house Circuit Coverage ............................................. 13

Battery Charger Installation .................................................. 13

Electrical Connections .......................................................... 13

Operational Testing ............................................................... 14

Appendix C - PowerMaster™ Load Controller

Installation and Operationa Testing .................................... 16

Operational Testing ............................................................... 17

Checking the Priority Load Controller .................................. 20

Appendix D - PowerManager™ Load Shed Transfer

Switch Installation and Operational Testing ...................... 21

Battery Charger Installation .................................................. 22

Electrical Connections .......................................................... 22

Operational Testing ............................................................... 24

Verifying Load Shedding Operation ..................................... 25

Appendix E - GenReady™ Load Center Installation

and Operational Testing ....................................................... 28

Battery Charger Installation .................................................. 28

Electrical Connections .......................................................... 29

Operational Testing ............................................................... 30

Appendix F - Setting the Automatic Exercise

Function ................................................................................. 32

Notes .......................................................................................... 34

Electrical Data .......................................................................... 36

INTRODUCTION

This booklet and the accompanying video are designed to famil-

iarize personnel with the installation process for air-cooled gen-

erators. This booklet does not replace or supersede any informa-

tion contained in any of the other written documents shipped with

the equipment. This booklet should only be use in conjunction

with the Owner’s Manual, Installation Guide and other technical

documents shipped with the equipment.

Future product updates and/or modiﬁ cations will be reﬂ ected in

the written documentation included with Generac equipment.

Always read all accompanying documentation carefully before

attempting to install any generator, transfer switch or related

equipment.

It is essential to comply with all regulations established by the

Occupational Safety and Health Administration (OSHA) and

strict adherence to all local, state and national codes is mandatory.

Study the SAFETY RULES in the Owner’s Manual carefully

before installing, operating or servicing any equipment. Use

this guide ONLY in conjunction with the Owner’s Manual and

Installation Guide shipped with the generator. The generator

can operate safely, efﬁ ciently and reliably only if it is properly

installed, operated and maintained.

The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals afﬁ xed to the unit are, therefore, not all-inclusive.

Despite the safe design of this generator, operating this

equipment imprudently, neglecting its maintenance or being

careless can cause possible injury or death.

Permit only responsible and capable persons to install, operate or

maintain this equipment.

Potentially lethal voltages are generated by these machines.

Ensure all steps are taken to render the machine safe before

attempting to work on the generator.

Caution, risk of electrical shock! The neutral conductor must

be bonded to ground in accordance with the National Electrical

Code, NFPA 70. This unit shall not be used in ﬂ oating output

applications.

GENERAL HAZARDS

For safety reasons, the manufacturer recommends that this equipment

be installed, serviced and repaired by a Service Dealer or other

competent, qualiﬁ ed electrician or installation technician who is

familiar with applicable codes, standards and regulations. The operator

also must comply with all such codes, standards and regulations.

Installation, operation, servicing and repair of this (and related)

equipment must always comply with applicable codes, standards,

laws and regulations. Adhere strictly to local, state and national

electrical and building codes. Comply with regulations the

Occupational Safety and Health Administration (OSHA) has

established. Also, ensure that the generator is installed, operated

and serviced in accordance with the manufacturer’s instructions

1

and recommendations. Following installation, do nothing that

might render the unit unsafe or in noncompliance with the

aforementioned codes, standards, laws and regulations.

Engine exhaust fumes contain carbon monoxide gas, which

can be DEADLY. This dangerous gas, if breathed in sufﬁ cient

concentrations, can cause unconsciousness or even death. For

that reason, adequate ventilation must be provided. Exhaust gases

must be piped safely away from any building or enclosure that

houses the generator to an area where people, animals, etc., will

not be harmed. This exhaust system must be installed properly, in

strict compliance with applicable codes and standards.

Keep hands, feet, clothing, etc., away from drive belts, fans, and

other moving or hot parts. Never remove any drive belt or fan

guard while the unit is operating.

Adequate, unobstructed ﬂ ow of cooling and ventilating air is

critical to prevent buildup of explosive gases and to ensure

correct generator operation. Do not alter the installation or

permit even partial blockage of ventilation provisions, as this can

seriously affect safe operation of the generator. Never install a

generator indoors.

Keep the area around the generator clean and uncluttered. Remove

any materials that could become hazardous. When working on this

equipment, remain alert at all times. Never work on the equipment

when physically or mentally fatigued.

GENERATOR INSTALLATION

These generators are air-cooled, engine-driven generator sets

designed to supply electrical power that operates critical electrical

loads during utility power failure. These generators are factory-

installed in a weather resistant, all metal enclosure and are intended

for outdoor installation only.

BEFORE INSTALLATION

The generator’s rated wattage/amperage capacity must be adequate to

handle all electrical loads that the unit will power. The critical priority

loads may need to be grouped together and wired into a separate

priority circuits distribution panel.

Each generator has a minimum fuel volume requirement. Refer

to the owner’s manuals for the generator fuel consumption.

Verify that the natural gas meter presently installed at the house

will support both the generator fuel load as well as any other

gaseous appliances that will require

fuel to operate if powered by

the generator. If an LP application,

verify that the fuel tank and pipe

is large enough to sustain the necessary volume even during cold

temperatures.

Connecting this generator to an electrical system normally

supplied by an electric utility shall be by means of a transfer

switch, so as to isolate the electric system from the utility

distribution system when the generator is operating. Failure to

isolate the electric system by these means will result in damage

to the generator and may also result in injury or death to utility

workers due to backfeed of electrical energy.

The engine-generator is to be installed over non-combustible

materials and should be located such that combustible materials

are not capable of accumulating under the generator set.

Only qualiﬁ ed, competent installation contractors or electricians

thoroughly familiar with applicable codes, standards and

regulations should install this standby electric power system. The

installation must comply strictly with all codes, standards and

regulations pertaining to the installation.

After the system has been installed, do nothing that might render

the installation in non-compliance with such codes, standards and

regulations.

NFPA STANDARDS

The following published standards booklets pertaining to standby

electric systems are available from the National Fire Protection

Association (NFPA), Batterymarch Park, Quincy, MA 02269:

NFPA No. 37, STATIONARY COMBUSTION

ENGINES AND GAS TURBINES

NFPA No. 54, NATIONAL FUEL GAS CODE

NFPA No. 58, LIQUIFIED PETROLEUM GAS CODE

NFPA 70, National Electrical Code (NEC)

NFPA 99, STANDARD FOR HEALTH CARE

FACILITIES

NFPA 101, LIFE SAFETY CODE

NFPA 110, STANDARD FOR EMERGENCY AND

STANDBY POWER SYSTEMS

NFPA 220, STANDARD TYPES OF BUILDING

CONSTRUCTION

NOTE: It is essential to use the latest version of any standard to

ensure that the generator and its accessories comply with all the

applicable standards and local codes.

OTHER PUBLISHED STANDARDS

In addition to NFPA standards, the following information

pertaining to the installation and use of standby electric systems

is available:

Article X, NATIONAL BUILDING CODE, available •

from the American Insurance Association, 85 John Street,

New York, N.Y. 10038.

AGRICULTURAL WIRING HANDBOOK, obtainable •

from the Food and Energy Council, 909 University

Avenue, Columbia, MO, 65201.

ASAE EP-364.2, INSTALLATION AND •

MAINTENANCE OF FARM STANDBY ELECTRIC

POWER, available from the American Society of

Agricultural Engineers, 2950 Niles Road, St. Joseph, MI

49085.

A52.1, AMERICAN NATIONAL STANDARDS

•

FOR CHIMNEYS, FIREPLACES AND VENTING

SYSTEMS, available from the American National

Standards Institute, 1430 Broadway, New York, NY

10018.

The installer must comply with all applicable state and local

codes.

2

GROUNDING THE GENERATOR

A grounding lug is provided on the generator mounting base for

the purpose of grounding the frame and the external electrically

conductive parts of this equipment to an approved earth ground

and/or grounding rods where required by the National Electrical

Code. Grounding procedures must meet local regulations.

BATTERY INSTALLATION

Standby generators installed with automatic transfer switches will

crank and start automatically when NORMAL (UTILITY) source

voltage is removed or is below an acceptable preset level. To

prevent such automatic start-up and possible injury to personnel,

do not connect battery cables until certain that normal source

voltage at the transfer switch is correct and the system is ready to

be placed into operation.

Storage batteries give off explosive hydrogen gas. This gas can

form an explosive mixture around the battery for several hours

after charging. The slightest spark can ignite the gas and cause

an explosion. Such an explosion can shatter the battery and

cause blindness or other injury. Any area that houses a storage

battery must be properly ventilated. Do not allow smoking, open

ﬂ ame, sparks or any spark producing tools or equipment near the

battery.

Battery electrolyte ﬂ uid is an extremely caustic sulfuric acid

solution that can cause severe burns. Do not permit ﬂ uid to

contact eyes, skin, clothing, painted surfaces, etc. Wear protective

goggles, protective clothing and gloves when handling a battery.

If ﬂ uid is spilled, ﬂ ush the affected area immediately with clear

water.

Do not dispose of the battery in a ﬁ re. The battery is capable of

exploding.

Do not open or mutilate the battery. Released electrolyte can be

toxic and harmful to the skin and eyes.

The battery represents a risk of high short-circuit current. When

working on the battery, always remove watches, rings or other

metal objects, and only use tools that have insulated handles.

VENTED BATTERIES

The electrolyte is a dilute sulfuric acid that is harmful to the

skin and eyes. It is electrically conductive and corrosive. The

following procedures are to be observed:

Wear full eye protection and protective clothing.•

If electrolyte contacts the skin, wash it off immediately with •

water.

If electrolyte contacts the eyes, ﬂ ush thoroughly and •

immediately with water and seek medical attention. Spilled

electrolyte is to be washed down with an acid-neutralizing

agent. A common practice is to use a solution of one pound

(500 grams) bicarbonate of soda to one gallon (4 liters) of

water. The bicarbonate of soda solution is to be added until the

evidence of reaction (foaming) has ceased. The resulting liquid

is to be ﬂ ushed with water and the area dried.

Lead acid batteries present a risk of ﬁ re because they generate •

hydrogen gas. The following procedures are to be followed:

DO NOT SMOKE when near batteries.•

DO NOT cause ﬂ ame or spark in battery area.•

Discharge static electricity from body before touching batteries •

by ﬁ rst touching a grounded metal surface.

Servicing of batteries is to be performed or supervised •

by personnel knowledgeable of batteries and the required

precautions. Keep unauthorized personnel away from batteries.

For recommended batteries, see the Installation Guide. All •

batteries must be at 100 percent state of charge before they are

installed on the generator.

It is important to check the speciﬁ c gravity and electrolyte •

level. Have these procedures performed at the intervals

speciﬁ ed in the “Maintenance” section in the Owner’s Manual.

A negative ground system is used. Battery connections are

shown on the wiring diagrams. Make sure all batteries are

correctly connected and terminals are tight. Observe battery

polarity when connecting batteries to the generator set.

NOTE: Damage could result if the battery connections are made

in reverse.

BEFORE YOU BEGIN

Contact the local inspector or City Hall to be aware of all federal,

state and local codes that could impact the installation. Secure all

required permits before starting the job.

Carefully read and follow all of the procedures and safety

precautions detailed in the installation guide. If any portion of the

installation manual, technical manual or other factory-supplied

documents is not completely understood, contact a dealer for

assistance.

Fully comply with all relevant NEC, NFPA and OSHA standards

as well as all federal, state and local building and electric codes.

As with any generator, this unit must be installed in accordance

with current NFPA 37 and NFPA 70 standards as well as any

other federal, state, and local codes for minimum distances from

other structures.

SITE PREPARATION AND GENERATOR

PLACEMENT

1. Locate the mounting area as close as possible to the transfer

switch and fuel supply.

3

Leave adequate room around the area for service access

(check local code), and place high enough to keep rising

water from reaching the generator.

Choose an open space that will provide adequate and

unobstructed airﬂ ow.

2. Place the unit so air vents won’t become clogged with

leaves, grass, snow or debris. Make sure exhaust fumes

will not enter the building through eaves, windows,

ventilation fans or other air intakes.

Dig a rectangular area approximately ﬁ ve inches deep and about

six inches longer and wider than the footprint of the generator.

Cover with polyurethane ﬁ lm and ﬁ ll with pea gravel or crushed

stone. Compact and level the stone. A concrete pad can be

poured if desired.

3. Inspect the generator for shipping damage and if

necessary, ﬁ le a claim with the shipper.

Remove the bands holding the generator to the wooden

pallet.

4. Make sure the lifting equipment to be used has sufﬁ cient

capacity to safely handle the weight of the generator.

Use nylon lifting straps and connect them to the lifting

eyes on each corner of the base frame to avoid damaging

the enclosure.

5. Set the generator onto the pad so that the gravel bed

extends several inches beyond the generator on all sides.

Make sure the generator is level within ½ inch.

6. Connect an approved ground strap to the grounding lug

on the base frame and to an approved earth ground or

grounding rod as speciﬁ ed by local regulations.

7. Check the engine oil and, if necessary, add enough of the

recommended oil to bring the level up to the FULL mark

on the dipstick. Be careful not to overﬁ ll the crankcase.

CONVERTING TO LP VAPOR

1. The generator was conﬁ gured for natural gas operation

at the factory. Switching over to LP Vapor is a simple

procedure.

4

On models with a single cylinder engine, begin by

disconnecting and removing the battery if installed.

2. Take the plastic T-handle fuel selector in the poly bag

supplied with the generator and locate the selector tab on

the air box cover. Insert the pin end into the hole in the

selector tab and pull outward to overcome spring pressure.

Then twist clockwise 90 degrees and allow the selector to

return in once aligned with the LP position.

3. On 10 kW units, open the roof, loosen the forward clamp

on the air inlet hose, and slide the hose away from the

hose ﬁ tting.

4. Slide the fuel selector pin on the carburetor out towards

the back of the enclosure.

5. Replace the inlet hose and tighten the clamp securely.

6. On all other models, simply remove the air cleaner cover

and slide the fuel selector pin outward from the natural gas

to the LP position.

INSTALLING & CONNECTING GAS LINES

1. Both natural gas and LP Vapor are highly volatile

substances, so strict adherence to all safety procedures,

codes, standards and regulations is essential.

Gas line connections should be made by a certiﬁ ed

plumber familiar with local codes. Always use AGA-

approved gas pipe and a quality pipe sealant or joint

compound.

Verify the capacity of the natural gas meter or the LP

tank in regards to providing sufﬁ cient fuel for both the

generator and other operating appliances.

2. Most applications will require an external manual shutoff

valve on the fuel line.

3. Where the gas line is to enter the generator, install a

T-ﬁ tting to allow for gas pressure monitoring. On one

opening of the ﬁ tting install a ¼” NPT nipple and threaded

plug. In some cases a sediment trap may also be installed.

5

4. When connecting the gas line to the generator, use the

provided section of UL Listed or AGA-approved ﬂ exible

fuel line in accordance with local regulations. The

purpose of the ﬂ exible fuel line is to ensure that vibration

from the generator does not cause a gas leak at one of

the connection points, so it’s important that the line be

installed with as few bends as possible.

5. Never bend the ﬂ exible fuel line to avoid using an elbow.

Bending the ﬂ exible line decreases its ability to absorb

vibrations and defeats its purpose as well as constricts the

actual fuel ﬂ ow.

6. After checking for leaks, check the gas pressure at the

T-ﬁ tting installed earlier to make sure there’s enough

pressure for proper generator operation.

The local gas supplier is responsible for ensuring adequate

pressure, so if the pressure is too low, or if it’s greater than

14 inches of water column, contact the gas supplier.

7. When ﬁ nished checking the gas pressure, close the manual

shutoff valve.

BATTERY CHARGER INSTALLATION

1. If the generator came with a separately packaged battery

charger, it may be necessary to install the charger,

either in

the generator or in the transfer switch. Refer

to documentation

included with the battery charger for

installation and wiring of the battery charger.

For applications with RTSN, RTSE and GenReady transfer

switches the charger needs to be mounted in the generator.

Refer to documentation included with the battery charger

for installation and wiring of the battery charger.

2. For applications with RTS Load Center switches and

RTSS Load Shed transfer switches the charger has already

been installed in the transfer switch. Discard the separately

packed battery charger that came with the generator.

6

EXTERNAL ELECTRICAL CONNECTIONS

1. Drill a 1 ¾ inch hole and feed the conduit through the hole.

2. Remove the knockout in the back of the connection box,

feed the wires through the back of the box and secure the

conduit with the lock nut.

Seal the hole with silicone caulk. Don’t forget to caulk the

hole inside the house as well.

3. Mount the connection box so that it completely covers the hole

in the wall. Caulk around the sides and top of the box to ensure a

good seal.

Connect all wires to the lugs in the connection box (black to

black, red to red and white to white). Attach the green ground

wire to the ground screw and connect the two small plugs to

their mating receptacle ends.

4. Replace the protective cover plate and retaining screw, and

lock the connection box.

5. For 10-20 kW models, locate the metal hasp that is

packaged in the owner’s manual bag. Insert the hasp in the

slot located on the left side of the external circuit breaker

box. Be sure that the clip of the hasp is facing toward the

front of the generator. If desired, lock the external box.

GENERATOR CONNECTIONS – RTS LOAD

CENTER TRANSFER SWITCH

1. If the generator comes with an external connection box

and 5’ seal-tite whip pre-wired and connected to the

generator, no additional connections are necessary at the

generator. Skip the following section and proceed with

Appendix A, RTS Pre-Wired Load Center Transfer Switch

Installation & Operational Testing.

2. If the RTS Load Center transfer switch was purchased

separately from the generator, the 5’ seal-tite whip will

need to be connected to the generator. To complete the

wiring, run the ¾” conduit for the power leads and control

wires from the external connection box to the generator.

7

3. Remove the two screws securing the connection area

cover, and remove the cover.

4. Feed the wires through the back of the generator and

secure the conduit with the lock nut.

5. Run the power leads through the strain relief provided.

6. On 8 kW units, the main breaker is located inside the

generator at the rear of the connection area.

7. For all other models the circuit breaker is attached to the

exterior access panel.

8. Remove the plastic plugs inside the main breaker access

area to allow connection of the power leads to the circuit

breaker.

9. Now connect the red and black power leads to the circuit

breaker. Since this is a single-phase application, it doesn’t

matter which wire is connected to which lug.

10. Connect the green equipment ground wire to the ground

stud and torque to 80 inch lbs.

11. Connect the white neutral wire to the neutral post and

torque to 80 inch lbs.

12. Connect the control wires to the correct terminals. The

terminals are clearly marked N1, N2, 23 and 15B. If

connecting a pre-wired switch a 0 (zero) wire will also be

required.

8

13. If the battery charger was factory mounted in the transfer

switch, 0 (zero) will also need to be connected between

the generator and transfer switch.

14. An improperly connected control wire can damage the

generator control board.

APPENDIX A – RTS PRE-WIRED

LOAD CENTER TRANSFER SWITCH

INSTALLATION & OPERATIONAL TESTING

1. Before beginning any installation, make sure power is shut

OFF to the main distribution panel and carefully read the

Owner’s Manual that came with the transfer switch.

The distributed load center switch must be mounted close

enough to the main distribution panel to accommodate

the two-foot, pre-wired conduit. Make sure no water or

corrosive substances can drip onto the transfer switch

enclosure.

2. Always inspect the switch for shipping damage. Never

mount a transfer switch that shows any evidence of

damage.

3. Protect against impact and mount the switch vertically to

a rigid support structure. Make sure the switch is level and

plumb.

The transfer switch is an open transition switch. Open

transition switches prevent electrical feedback between the

generator and the utility by only allowing load circuits to

be connected to one power supply at a time.

4. Each wire in the pre-wired transfer switch is color-coded

to easily match circuits in the main panel to their new

breakers in the transfer switch.

5. When three-conductor wiring is used, two 120 volt

circuits will often share the same neutral wire. To avoid

overloading the neutral, either move BOTH of the circuits

that share the neutral or don’t move either of them.

6. When moving two circuits with a shared neutral, they

should be connected to adjacent positions (one above the

other) in the transfer switch. That will assure that the two

hot wires are on separate phases and will maintain their

relationship to neutral.

9

7. Choose a circuit to be backed up and remove the power

lead from the breaker.

8. Using UL Listed wire nuts, reconnect the power lead to a

matching breaker in the transfer switch.

9. Make sure each circuit moved is protected by the same

size breaker in the transfer switch. 15 Amp circuits must

be connected to 15 Amp breakers and 20 Amp circuits to

20 Amp breakers.

10. Connect the provided large neutral to the neutral bar in the

distribution panel.

11. Install a 2-pole breaker in the distribution panel to protect

the transfer switch. The required amp rating of the breaker

depends on which transfer switch is used. If installing an

8-circuit, pre-wired load center switch, the breaker cannot

exceed 40 Amps. For all other pre-wired load center

switches the breaker cannot exceed 70 Amps. This breaker

must be compatible with the existing electrical distribution

panel.

Install the breaker in two adjacent empty slots (one above

the other) in the main panel.

12. When all priority circuits have been moved to the transfer

switch, close the main breaker to restore utility power and

make sure utility voltage at the transfer switch is correct.

Refer to NFPA 70-E for the safety equipment required

when working inside a live transfer switch.

13. Before purchasing a battery for the generator, refer to

the generator Owner’s Manual for a list of recommended

batteries. Follow all of the procedures and safety

precautions in the Owner’s Manual when installing the

battery.

BATTERY INSTALLATION

1. Before purchasing a battery for the generator, refer to the

Owner’s Manual for the recommended battery.

• 8 kW: Group 26R, 12 Volt, 350cca minimum

• 10-20 kW: Group 26R, 12 Volt, 525cca minimum

10

2. Follow all of the procedures and safety precautions in the

generator Owner’s Manual when installing the battery.

Verify the switch is in the off position. When preparing

for operational testing, DO NOT connect the battery until

transfer switch connections are complete.

OPERATIONAL TESTING

1. Switch the generator’s main circuit breaker OFF and put

the mode switch in the OFF position.

2. Make sure utility power is OFF and place all of the

priority circuit breakers in the transfer switch in the OFF

position.

3. Locate the transfer handle, insert the metal end into the

slot in the main contactor assembly and pull the handle

DOWN to move the main contacts to the standby power,

or generator position.

NEVER OPERATE THE TRANSFER SWITCH

MANUALLY WHEN LOADS ARE CONNECTED.

4. Put the generator’s mode switch in MANUAL to start

the engine.

Allow the engine to warm up, then switch

the generator’s main breaker to the ON position. The

generator is now supplying electricity to the transfer

switch but is not carrying any load.

5. For all models except the 8 and 10kW check to be sure

that voltage and frequency from the generator is correct. If

line-to-line voltage is not approximately 240 volts, refer to

the Owner’s Manual for the proper adjustment procedures.

On all models, if line-to-neutral voltage is not 120 volts,

check the neutral connection between the generator and

transfer switch.

For 8 kW models check to be sure that the frequency

from the generator is correct. If the frequency is not

approximately 60Hz, refer to the generator Owner’s

Manual for the proper adjustment procedure.

6. When ﬁ nished checking the voltage, switch the generator’s

main circuit breaker OFF and put the mode switch in the

OFF position to shut down the generator.

11

7. Make sure the 2-pole circuit breaker installed in the main

distribution panel is in the OFF position.

8. Use the transfer handle to move the main contacts in the

transfer switch to the UP (utility position). Switch the

2-pole breaker ON in the distribution panel.

9. Now switch the generator’s main breaker ON, and put the

mode switch in AUTO.

10. Shut OFF utility power and make sure the generator starts

automatically.

11. If everything worked properly, switch the main breaker to

ON and make sure that power is automatically transferred

back to the utility.

12. After the engine has completed its cool down cycle and

shut down, shut OFF utility power again.

When the generator is supplying power to the transfer

switch, move the breakers in the switch to the ON

position, one at a time, until the generator has accepted the

entire priority load.

13. With the generator carrying the entire priority load,

recheck gas pressure to verify that it is at the same level it

was before the generator was started.

NOTE: Even if the generator is running smoothly at this

point, a drop in gas pressure indicates that the supply is barely

adequate to supply the generator’s needs. Changes in the

generator load, or additional gas demand by other appliances

may affect the generator’s performance. Verify gas pressure

and pipe sizing.

Unhook the manometer and reinstall the port

plug.

14. Switch the main breaker ON to restore utility power.

The generator will continue to run to allow the engine to

cool down before shutting itself off.

Shut off utility power again. The generator should start and

the entire priority load should transfer to the generator.

Close the main breaker to restore utility power and allow

the engine to cool down and shut itself off.

15. Operational tests are now complete. Refer to – Setting the

Automatic Exercise Function to complete the installation.

12

APPENDIX B – RTSN AND RTSE TRANSFER

SWITCH INSTALLATION & OPERATIONAL

TESTING

1. Before beginning any installation, make sure power is shut

OFF to the main distribution panel and carefully read the

Owner’s Manual that came with the transfer switch.

To simplify the installation process, the transfer switch

should be mounted as close to the main distribution panel

as possible. Make sure no water or corrosive substances

can drip onto the transfer switch enclosure.

2. Always inspect the switch for shipping damage. Never

mount a transfer switch that shows any evidence of

damage.

3. Protect against impact and mount the switch vertically to a

rigid support structure. Make sure the switch is level and

plumb.

Check local codes before wiring the transfer switch. Some

jurisdictions require that wiring inside the switch be done

by a licensed electrician.

4. All wiring must be the correct size and type, and must

conform to all codes, standards and regulations. Refer

to the transfer switch Owner’s Manual and the National

Electrical Code for additional information.

5. As with any product, design changes can occur over time,

so always refer to the schematics in the transfer switch

Owner’s Manual for the required connections and safety

precautions.

6. The transfer switch being used is an open transition

switch. Open transition switches prevent electrical

feedback between the generator and the utility by only

allowing load circuits to be connected to one power supply

at a time.

SELECTED CIRCUIT COVERAGE

1. The generator powers only designated circuits that are

grouped together and wired into a separate priority

distribution panel. The transfer switch is installed between

the main distribution panel and the priority panel.

The amperage rating of the transfer switch must be equal

to or greater than the highest amperage rating of the utility

and generator breakers feeding the switch.

13

WHOLE-HOUSE CIRCUIT COVERAGE

1. The generator will be backing up all electrical loads within

the panel, so the amperage rating of the transfer switch

must be equal to or greater than the amperage rating of the

normal utility service.

Unless a service entrance rated transfer switch is used,

a main service disconnect must be located before the

transfer switch. The transfer switch must be installed

between the utility service entrance and the building

distribution panel.

2. A service entrance rated transfer switch is installed

between the service entrance and the main distribution

panel. The service entrance rated switch becomes the main

service so no service disconnect is needed. The existing

main distribution panel becomes a sub-panel.

3. The grounding that is normally in the main panel must

be accomplished in the service entrance rated switch and

must be disconnected in the existing distribution panel.

Refer to the National Electrical Code (NEC) for complete

information on grounding and bonding.

BATTERY CHARGER INSTALLATION

1. The battery charger is to be installed in the generator when

using an RTSN or RTSE transfer switch. Refer to the

Battery Charger Installation Guide for details.

ELECTRICAL CONNECTIONS

1. Connect the power leads from both the generator and the

utility to the appropriate lugs in the transfer switch. The

lugs are clearly marked in the switch.

N = Normal Utility Supply

E = Generator Connection Panel

T = Load Distribution Panel

2. Neutral wires from both the utility and the generator are

connected to the same neutral lug in the switch.

14

3.

Connect the control wires from the generator to the terminal

block in the transfer switch. The terminals are marked N1,

N2, 23 and (194 or 15B). If the fourth terminal in the transfer

switch is labeled 194, wire 15B from the generator will

connect to terminal 194 in the transfer switch.

4. Complete the transfer switch wiring by connecting the

equipment ground wires from both the utility and the

generator to the ground lug.

5. Being careful to support the lugs, torque the lugs in the

transfer switch to the speciﬁ cations shown on the transfer

switch. Decal located on the inside of the switch door.

OPERATIONAL TESTING

1. If installing the RTSE switch, the service was changed so

make sure the terminations are good before re-energizing the

utility.

2 Switch the main utility breaker OFF. Refer to NFPA 70-E

for the safety equipment required when working inside a

live transfer switch.

3. Energize the utility and check line-to-line and line-to-

neutral voltage at terminals N1 and N2 on the transfer

contactor. If line-to-line voltage is not approximately 240

volts, de-energize utility power and check the terminations

between the utility and N1 and N2.

If line-to-neutral voltage is not approximately 120 volts, de-

energize utility power and check the neutral terminations.

Repeat the same voltage checks on terminals T1 and

T2 to make sure current is ﬂ owing properly through the

contactor.

4. Switch the generator’s main circuit breaker OFF and put

the mode switch in the OFF position.

5. Make sure utility power is OFF and place all of the

individual

circuit

breakers in the main distribution panel in

the OFF position.

15

6. Locate the transfer handle, insert the metal end into

the slot in the main contactor assembly. Pull the handle

DOWN to move the main contacts to the standby power

(generator) position.

NEVER OPERATE THE TRANSFER SWITCH

MANUALLY WHEN LOADS ARE CONNECTED.

7. Put the generator’s mode switch in MANUAL to start the

engine.

Allow the engine to warm up, then switch the generator’s

main breaker to the ON position. The generator is now

supplying electricity to the transfer switch but is not carrying

any load.

8. For all models except the 8 and 10 kW check to be sure

that voltage and frequency from the generator is correct.

If line-to-

line voltage is not approximately 240 volts, refer

to the generator

Owner’s Manual for the proper adjustment

procedures. On all models, if line-to-neutral voltage is

not approximately 120 volts, check the neutral connection

between the generator and transfer switch.

For 8 kW models check to be sure that the frequency

from the generator is correct. If the frequency is not

approximately 60Hz, refer to the generator Owner’s

Manual for the proper adjustment procedure.

9. Switch the generator’s main circuit breaker OFF and put

the mode switch in the OFF position to shut down the

generator.

10. With utility power still OFF, use the transfer handle to

move the main contacts to the UP (utility) position.

11. Close the main breaker to turn utility power ON.

12. Switch the generator’s main breaker to the ON position

and put the mode switch in AUTO.

13. Shut OFF utility power and make sure the generator starts

automatically after the line interrupt delay.

16

14. Switch the utility breaker to ON and make sure that power

is automatically transferred back to the utility.

15. Shut OFF utility power again to automatically start the

generator. When power has transferred to the generator,

close each of the breakers in the distribution panel one at a

time until the generator has accepted the entire load.

16. With the generator carrying the entire load, recheck gas

pressure to verify that it’s at the same level it was before

the generator was started.

NOTE: Even if the generator is running smoothly at this

point, a drop in gas pressure indicates that the supply is barely

adequate to supply the generator’s needs. Changes in the

generator load, or additional gas demand by other appliances

may affect the generator’s performance. Verify gas pressure

and pipe sizing. Unhook the manometer and reinstall the port

plug.

17. Switch the utility breaker ON to restore utility power to

the home.

18. The generator will continue to run to allow the engine to

cool down, then shut itself off.

19. Shut OFF utility power again. The generator should start

and the entire priority load should transfer to the generator.

20. Close the main breaker to restore utility power and allow

the engine to cool down and shut itself off.

Operational tests are now complete. Refer to – Setting the

Automatic Exercise Function to complete the installation.

APPENDIX C – POWERMASTER

™

LOAD

CONTROLLER INSTALLATION AND

OPERATIONAL TESTING

1. The PowerMaster load controller should be mounted as

close to the main distribution panel as possible to avoid

splicing. Refer to the instructions and wiring diagram in

the PowerMaster Technical Manual before beginning the

installation.

2. After making sure that all power supplies are shut off,

remove the power leads from the 240 volt, 2-pole breaker

that controls the selected appliance.

17

3. Using the ring lugs provided and the wire speciﬁ ed in the

PowerMaster Technical Manual, connect one end of new

power leads to one of the contactors in the load controller.

4. Connect the other end of the new power leads to the

appliance breaker in the distribution panel.

5. Connect the power leads that were removed from the

appliance breaker to the load terminals in the controller.

6. Now run 24 volt control wires from the air conditioning

circuit to the terminal strip in the controller.

7. The auxiliary switches that came with the controller

must be installed in the transfer switch. These switches

ensure that the controller will only disconnect the selected

appliances when utility power is off and the generator

is running. Refer to the Technical Manual for speciﬁ c

instructions for installing the auxiliary switches.

8. Connect one end of two control wires to the COMMON

and NORMALLY OPEN pins on the generator side of the

transfer switch.

9. Connect the other ends of the control wires to the

COMMON and NORMALLY OPEN positions of the

selected control circuit in the controller.

If moving a second load to the controller, follow the same

procedure.

OPERATIONAL TESTING

1. Switch the generator’s main circuit breaker OFF and put

the mode switch in the OFF position.

18

2. If using a service entrance rated transfer switch, put the

generator disconnect switch in the ON position if applicable.

3. Make sure utility power is OFF and place all of the

individual circuit breakers in the main distribution panel in

the OFF position.

4. Locate the transfer handle and insert the metal end into the slot in

the main contactor assembly. Pull the handle DOWN to move the

main contacts to the standby power (generator) position.

NEVER OPERATE THE TRANSFER SWITCH

MANUALLY WHEN LOADS ARE CONNECTED.

5. Put the generator’s mode switch in MANUAL to start the

engine.

Allow the engine to warm up, then switch the generator’s

main breaker to the ON position. The generator is now

supplying electricity to the transfer switch but is not

carrying any load.

6. Check voltage and frequency from the generator. If line-to-

line voltage is not 240 volts, refer to the Installation Guide

for the proper adjustment procedures. If line-to-neutral

voltage is not 120 volts, check the neutral connection

between the generator and transfer switch.

Switch the generator’s main circuit breaker OFF and put the

mode switch in the OFF position to shut down the generator.

7. With utility power still OFF, use the transfer handle to

move the main contacts to the UP (utility) position.

8. Close the main breaker to turn utility power ON.

9. Switch the generator’s main breaker to the ON position an

put the mode switch in AUTO.

La page est en cours de chargement...

Generac 17 kW 0056130 Manuel utilisateur

Generac 17 kW 0056130 Manuel utilisateur

dans d''autres langues

Documents connexes