ZyXEL N-4100 Le manuel du propriétaire

www.zyxel.com

Wireless N HotSpot Gateway

Version 1.00

Edition 1, 02/2010

N4100

DEFAULT LOGIN DETAILS

IP Address: http://192.168.1.1

Username: admin

Password: 1234

CONTENTS

ENGLISH 3

DEUTSCH 17

ESPAÑOL 35

FRANÇAIS 53

ITALIANO 71

РУССКИЙ 89

SVENSKA 107

繁體中文

123

ZyXEL Communications Corporation

2

Device Panels

RESET

POWER

LEDs

LAN/WAN Connectors

Antennas

ENGLISH

3

Introduction

The N4100 combines an IEEE 802.11b/g/n wireless access point, router,

4-port switch and service gateway in one box. A "statement printer"

allows you to easily generate subscriber accounts and print account

statements. You can connect it directly to the N4100. The subscriber is a

client with authenticated access to the Internet through the N4100.

In this example, a computer connects to the N4100’s (a) LAN port for

management. You also attach a RADIUS server for subscriber

authentication and a statement printer (c) for statements printing. The

N4100 connects to a broadband modem (b), which then connects to the

Internet. Wireless subscribers have seamless Internet access through

the N4100.

In this guide, you will:

• Make Hardware Connections to set up your device.

• Access the Web Configurator to use the Setup Wizard to configure

the WAN connection, wireless settings, e-mail and authentication

services, and set the billing profile on the N4100. You can also use

the wizard to set how to generate accounts and print statements,

and change the system password and time.

LAN

WLAN

WAN

a

b

c

ENGLISH

4

• Hang the N4100 on a wall.

Hardware Connections

This section shows you how to set up your N4100.

1

2

3

4

ENGLISH

5

1. LAN 1~4: Use Ethernet cables to connect the LAN ports to

computers, switches and a statement printer (optional).

2. WAN: Connect your broadband modem to this port with the Ethernet

cable that came with your modem.

3. Attach the included antennas to the N4100. The antennas should be

perpendicular to the ground and parallel to each other.

4. POWER: Connect the N4100's included power adaptor to the

N4100's power socket.

Check the LEDs (Lights)

Look at the LEDs (lights) on the front panel of the N4100.

• The PWR light (LED) turns on.

• The WAN or LAN light turns on if its corresponding port is properly

connected. The lights blink when the N4100 is sending or receiving

data through the corresponding port.

• The WLAN light stays green when the wireless LAN is enabled. It

blinks when the N4100 is sending/receiving data through the

wireless LAN.

• The SYS light turns on once the N4100 is ready.

6

 If no lights are on, check your connections. Make sure that

you have the power adaptor connected to the N4100 and

plugged in to an appropriate power source. Make sure the

power source is turned on. Turn the N4100 off, wait for a few

seconds and turn it back on. If the LEDs are still off, contact

your local vendor.

Web Configurator

This section shows you how to access and log into the Web

Configurator.

1. From the computer connected to the N4100, open a web browser

such as Internet Explorer or Firefox.

2. Enter http://192.168.1.1 (the

N4100’s default LAN IP address) in

the browser’s address bar.

3. Enter admin as the default user name and 1234 as the default

password. Click Login.

ENGLISH

7

 If the login screen does not display, make sure you allow

web browser pop-up windows, JavaScript and Java

permissions. Your computer should be also set to get an IP

address automatically from a DHCP server. See the User’s

Guide for more information.

Setup Wizard

The wizard setup screens appear automatically after your first login.

1. Fill in the fields with information from your ISP. The screen varies

depending on the encapsulation type you use. Leave fields set to the

default if you don't have that information.

If your ISP didn’t provide you any Internet access information, select

DHCP Client.

8

If your ISP gave you an IP address (and gateway and DNS server

addresses), select

Static IP Setting and enter them.

If your ISP gave you a user name and password, select

PPPoE.

ENGLISH

9

If your ISP gave you a user name, password and IP address(es),

select

PPTP.

2. Enter a unique name (up to 32 printable 7-bit ASCII characters) as

the ESSID to identify the N4100 in the wireless LAN.

Select a channel (range of radio frequencies) that is not being used

by other wireless devices in the area.

Select a security type and enter a key for data encryption. If you set

Security to Disabled, any one within range can access your network

wirelessly.

WPA or WPA2 provides user authentication and data encryption.

Data encryption of WPA or WPA2 is stronger than WEP's. The pre-

shared key is case-sensitive ASCII characters (including spaces and

10

symbols). Use the advanced wireless setup screen if you want to use

WPA or WPA2 with a RADIUS server (see the User's Guide for

details).

WEP provides data encryption only (no user authentication).

3. You can configure a backup e-mail server in the event that a

subscriber's e-mail server is unreachable from the N4100.

ENGLISH

11

4. Select Yes to be able to create and use subscriber accounts that are

used to authenticate clients connecting to the Internet. This wizard

configures authentication and accounting settings for the N4100's

built-in local subscriber database. Use the advanced RADIUS setup

screen to use an external RADIUS server instead (see the User's

Guide for details).

5. Set the type of accounting to use. Set up Internet access time periods

and their prices.

12

6. You can use a statement printer to generate subscriber accounts and

print subscriber statements. If you do so, make sure that no other

devices on your network use the same IP address as the printer

(192.168.1.7 by default). If you need to change the printer port

number or IP address here, make sure you also change it in the

printer, see the printer's user's guide for how to do this.

You can alternatively generate subscriber accounts in the web-based

account generator and print the statements on your regular printer.

7. Select a subscriber billing profile for each button on the "exclusive

printer" (statement printer) or the web-based account generator. The

billing profile defines the maximum Internet access time and charge

per time unit.

Set how many copies of the subscriber statement to print.

Click Customize printout text to tailor the subscriber statements.

See the CUSTOMIZATION > Account Printout section in your

User’s Guide for how to tailor what displays on the subscriber

statements.

ENGLISH

13

For the three button (statement) printer, click I want to setup... to

also configure the web-based account generator settings.

Set the username and password for accessing the account generator.

Click Preview/Operate to open the account generator. The web-

based account generator panel displays. Click one or more of the

buttons to generate accounts.

14

Click View Account List to see the accounts you generated.

8. Change the N4100's management password and update the time.

You can also specify from which IP address the N4100 can be

managed. Click Finish to save your changes and go back to the

System Quick View screen.

ENGLISH

15

Generating and Printing

Subscriber Account Statements

If you have a statement printer connected and turned on, simply press

the buttons to generate and print subscriber account statements. If you

are using a PC-connected printer, do the following.

1. Launch your web browser and go to

http://192.168.1.1 (as in the Web

Configurator section).

2. Enter the web-based account generator

user name and password that you

configured in the wizard (see page 13).

3. Click the buttons in the screen to

generate accounts.

4. The details of each new account display

in a separate window. Click the Print

button to print out the account

statement.

Hardware Installation

In general, the best location for the access point is at the center of your

intended wireless coverage area. For better performance, mount the

N4100 high up in a spot free of obstructions.

Do not block the ventilation holes.

16

Wall-mounted Installation

1. Install the two included screws in the wall 80mm (3.15") apart. Do not

screw the screws all the way into the wall. Leave a small gap between

the head of the screws and the wall.

2. Make sure the screws are securely fixed to the wall and strong

enough to hold the weight of the N4100 with the connection cables.

3. Hang the N4100 on the screws.

DEUTSCH

17

Einführung

Der N4100 vereint einen drahtlosen IEEE 802.11b/g/n Access Point,

Router, 4-Port-Switch und Service-Gateway in einem Gerät. Mit dem

"Belegdrucker" können Sie problemlos Zugangskonten erzeugen und

Kontoberichte ausdrucken. Er kann direkt an den N4100 angeschlossen

werden. Der Benutzer ist ein Client mit authentifiziertem Zugriff auf das

Internet über den N4100.

In diesem Beispiel wird zur Verwaltung ein Computer an den LAN-Port

des N4100 (a) angeschlossen. Sie können auch einen RADIUS-Server

zur Subscriber-Authentifizierung und einen Kontoberichtsdrucker (c)

zum Ausdrucken der Kontenberichte anschließen. Der N4100 wird an

ein Breitbandmodem (b) angeschlossen, das dann wiederum die

Verbindung zum Internet herstellt. Drahtlose Subscribers haben über

den N4100 einen kabellosen Internetzugriff.

In diesem Benutzerhandbuch wird

beschrieben:

• Wie der Anschließen der Hardware Ihr Gerät einrichtet.

LAN

WLAN

WAN

a

b

c

DEUTSCH

18

• Wie Sie auf den Web-Konfigurator zugreifen können, um mit dem

Einrichtungsassistenten die WAN-Verbindung, die

Drahtloseinstellungen, den E-Mail- und Authentifizierungs-Dienst

und das Abrechnungsprofil auf dem N4100 zu konfigurieren. Sie

können mit dem Assistenten auch festlegen, wie die Konten und

Kontenberichte erzeugt werden sollen, und das Systemkennwort

und die Uhrzeit ändern.

• Wie Sie den N4100 an einer Wand installieren.

Anschließen der Hardware

DEUTSCH

19

In diesem Abschnitt wird beschrieben, wie der N4100 eingerichtet wird.

1. LAN 1~4: Schliesen Sie Computer, Switches und den Belegdrucker

(optional) mit einem Ethernet-Kabel an die LAN-Ports eines

Computers an.

1

2

3

4

20

2. WAN: Schließen Sie Ihr Breitband-Modem an diesen Anschluss mit

dem Ethernet Kabel, das mit dem Modem geliefert wurde, an.

3. Schließen Sie die mitgelieferten Antennen an den N4100 an. Die

Antennen sollten senkrecht zum Boden und parallel zueinander

angeordnet sein.

4. POWER: Schließen Sie den Stromadapter des N4100 an den

Stromanschluß des N4100 an.

Die Bedeutung der LED-Anzeigen

Der N4100 verfügt an seiner Vorderseite über eine Reihe von LED-

Anzeigen.

• Die PWR-LED leuchtet.

• Die WAN- oder LAN-LED leuchtet, wenn ein Gerät am

entsprechende Port richtig angeschlossen wurde. Die LEDs

blinken, während der N4100 Daten über den jeweiligen Port sendet

oder empfängt.

• Die WLAN-LED leuchtet grün, wenn das drahtlose LAN aktiviert ist.

Sie blinkt, während der N4100 Daten über die Drahtlosverbindung

sendet/empfängt.

• Die SYS-LED leuchtet, sobald der N4100 bereit ist.

La page charge ...

ZyXEL N-4100 Le manuel du propriétaire

Ce manuel convient également à

ZyXEL N-4100 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents