Norcold N1095 Guide d'installation

Marque: Norcold

Modèle: N1095

Catégorie: Cheminées

Taper: Guide d'installation

For N109X and N109XXX models: 10 cu.ft., 2-way R.V. refrigerators.

For N109XIM and N109XIMXX models: 10 cu.ft., 2-way R.V. refrigerators with ice maker.

The letter “X”, in the model numbers above, stands for a letter or numeral which means a

refrigerator option.

NORCOLD, Inc.

P.O. Box 4248

Sidney, OH 45365-4248

Part No. 635490E(4/1/2020)

English

Installation Manual

Norcold Customer Support Dept.

Telephone: 800-543-1219

Fax: 734-769-2332

Web Site: www.norcold.com

Improper installation, adjustment, alteration, service or maintenance can

cause injury or property damage. Refer to this manual. For assistance

or additional information, contact a qualied installer, service agency, or

the gas supplier.

WARNING

FIRE OR EXPLOSION HAZARD

If you smell gas:

1. Open Windows

2. Do not attempt to light appliance.

3. Do not touch electrical switches.

4. Extinguish any open ame

5. Shut o fuel supply.

6. Evacuate immediately and call emergency services.

Failure to follow these instructions could result in re or explosion, which could cause

property damage, personal injury, or death.

WARNING

FOR YOUR SAFETY

Do not store or use gasoline or other ammable vapors and liquid in the

vicinity of this or any other appliance.

DO NOT install this refrigerator in below deck marine applications. Do not install this refrigerator in a

xed indoor cabin or other dwelling applications. This refrigerator must use only NORCOLD designed and

approved outside air intake and exhaust ventilation for correct and safe operation. Any other ventilation

could cause lethal combustion exhaust fumes and/or explosive propane gas fumes to be in the living area

and/or to be below deck.

WARNING

Installation Manual 2

Table of Contents

Safety Awareness

Safety Instructions

Safety Awareness ..................................................................................................................................................................................... 2

Safety Instructions ....................................................................................................................................................................................2

Certication and Code Requirements.......................................................................................................................................................3

Ventilation Requirements..........................................................................................................................................................................4

Key Refrigerator Dimensions....................................................................................................................................................................5

Assemble the Enclosure for the Refrigerator............................................................................................................................................5

Install the Lower and Upper Vents............................................................................................................................................................6

Rear Wall Installation ..............................................................................................................................................................................10

Reverse the Door Swing-Nonmetal Doors (optional) .............................................................................................................................10

Reverse the Door Swing-Metal Doors (optional) ....................................................................................................................................13

Install the Decorative Door Panels (nonmetal door models) ..................................................................................................................15

Install the Refrigerator ............................................................................................................................................................................16

Connect the Ice Maker (N109XIM, and N109XIMXX models)................................................................................................................17

Connect the water supply line .........................................................................................................................................................17

Connect the Electrical Components .......................................................................................................................................................17

Connect the 120 volts AC supply ....................................................................................................................................................18

Connect the 12 volts DC supply ......................................................................................................................................................18

Connect the Low Ambient Heater (optional) ...........................................................................................................................................19

Connect the Propane Gas Components.................................................................................................................................................19

Connect the propane gas supply system ........................................................................................................................................19

Examine the gas supply system for leaks .......................................................................................................................................20

Ignition and Start Up ............................................................................................................................................................................... 21

Ignition and start up ......................................................................................................................................................................... 21

Do a test of the gas safety valve .....................................................................................................................................................21

Shut down .......................................................................................................................................................................................22

Fault Codes ...........................................................................................................................................................................................22

Read this manual carefully and understand the contents before you install the refrigerator.

Be aware of possible safety hazards when you see the safety alert symbol on the refrigerator and in this manual. A signal word follows

the safety alert symbol and identies the danger of the hazard. Carefully read the descriptions of these signal words to fully know their

meanings. They are for your safety.

This signal word means a hazard, which if ignored, can cause dangerous personal injury, death, or much

property damage.

This signal word means a hazard, which if ignored, can cause small personal injury or much property

damage.

- This refrigerator is not approved for use as a free standing refrigerator. It is equipped for the use of propane gas only

and can not be changed to use any other fuels (natural gas, butane, etc.).

- Incorrect installation, adjustment, alteration, or maintenance of this refrigerator can cause personal injury, property

damage, or both.

- Obey the instructions in this manual to install intake and exhaust vents.

- Do not install the refrigerator directly on carpet. Put the refrigerator on a metal or wood panel that extends the full

width and depth of the refrigerator.

WARNING

CAUTION

Installation Manual 3

- Do not allow anything to touch the refrigerator cooling system.

- Propane gas can ignite and cause an explosion that can result in property damage, personal injury, or death. Do not

smoke or create sparks. Do not use an open ame to examine the propane gas supply line for leaks. Always use two

wrenches to tighten or loosen the propane gas supply line connections.

- Make sure the electrical installation obeys all applicable codes. See “Certication and Code Requirements” section.

- Do not bypass or change the refrigerator’s electrical components or features.

- Do not spray liquids near electrical outlets, connections, or the refrigerator components. Many liquids are electrically

conductive and can cause a shock hazard, electrical shorts, and in some cases re.

- The refrigerator cooling system is under pressure. Do not try to repair or to recharge a defective cooling system.

- The cooling system contains sodium chromate. The breathing of certain chromium compounds can cause cancer. The

cooling system contents can cause severe skin and eye burns, and can ignite and burn with an intense ame. Do not

bend, drop, weld, move, drill, puncture, or hit the cooling system.

- The rear of the refrigerator has sharp edges and corners. To prevent cuts or abrasions when working on the

refrigerator, use caution and wear cut resistant gloves.

Certication and Code Requirements

This refrigerator is certied by CSA International as meeting the

latest edition of ANSI Z21.19 / CSA 1.4 standards for installation in

mobile homes or recreational vehicles.

The refrigerator must be installed in accordance with this

“Installation Manual” in order for the Norcold limited warranty to be

in eect. In addition, the installation must conform to the following,

as applicable:

In the United States and Canada:

- Local codes, or in the absence of local codes, the National Fuel Gas Code, ANSI Z223.1/NFPA 54, the Natural Gas and Propane

installation Code, CSA B149.1, ANSI A119.2 Recreational Vehicles Code, and CSA Z240 RV Series, Recreational Vehicles.

- A manufactured home (mobile home) installation must conform with the Manufactured Home Construction and Safety Standard,

Title 24 CFR, Part 3280 [formerly the Federal Standard for Mobile Home Construction and Safety, Title 24 (part 280), and the

current CSA Z240.4, Gas-equipped Recreational Vehicles and Mobile Housing.

- If an external power source is utilized, the appliance, when installed, must be electrically grounded in accordance with local codes

or, in the absence of local codes, the National Electrical code, and ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.2.

Parts 1 and 2.

All propane gas supply piping and ttings must obey local, state, and national codes about type and size. These components must also

obey the current NFPA 501C section 2-4, and in Canada with the current CAN 1-6.10 Standard.

Art01290

CAUTION

Installation Manual 4

Ventilation Requirements

The completed installation must:

- Make sure there is sucient intake of fresh air for combustion.

- Make sure the living space is completely isolated from the combustion system of the refrigerator.

- Make sure there is complete and unrestricted ventilation of the ue exhaust which, in gas mode, can produce carbon

monoxide. The breathing of carbon monoxide fumes can cause dizziness, nausea, or in extreme cases, death.

- Make sure the refrigerator is completely isolated from its heat generating components through the correct use of

baes and panel construction.

Certied installation needs one lower intake vent and one upper exhaust vent. Install the vents exactly as written in this manual. Any

other installation method voids both the certication and the factory warranty of the refrigerator.

The bottom of the opening for the lower intake vent, which is also the service access door, must be even with or immediately below the

oor level. This allows any leaking propane gas to escape to the outside and not to collect at oor level.

CSA International certication allows the refrigerator to have zero (0) inch minimum clearance at the sides, rear, top, and bottom. While

there are no maximum clearances specied for certication, the following maximum clearances are necessary for correct refrigerator

performance:

Bottom 0 inch min. 0 inch max.

Each Side 0 inch min 1/2 inch max.

Top 0 inch min. 1/4 inch max.

Rear 0 inch min. 1 inch max.

These clearances plus the lower and upper vents cause the natural air draft that is necessary for good refrigeration. Cooler air comes

in through the lower vent, goes up around the refrigerator coils where it removes the excess heat from the refrigerator components, and

goes out through the upper vent. If this air ow is blocked or decreased, the refrigerator will not cool correctly.

Each NORCOLD model is certied by CSA International for correct ventilation. Install only the certied vents that are listed in this

manual.

WARNING

Installation Manual 5

Art01735

Key Refrigerator Dimensions

These key refrigerator dimensions are for your reference as

necessary (See Art01735).

Refrigerator cabinet width w/o trim:

23.47 in. max. ............................................................. 1

Refrigerator width overall w/ trim:

24.8 in......................................................................... 2

Refrigerator cabinet to side trim:

0.84 in......................................................................... 3

Refrigerator cabinet height w/o trim:

59.85 in. max. ............................................................. 4

Refrigerator height overall w/ trim:

62.0 in......................................................................... 5

Refrigerator cabinet to top/bottom trim:

1.13 in......................................................................... 6

Enclosure wall to hinges:

3.10 in......................................................................... 7

Refrigerator cabinet to center of handles:

40.5 in......................................................................... 8

Assemble the Enclosure for the

Refrigerator

1. Make sure the enclosure is 59.88 - 60.01 inches high x

23.50 - 23.63 inches wide x 24 inches deep.

2. Make sure the oor is solid and level.

- The oor must be metal or a wood panel and extend the

full width and depth of the enclosure.

- The oor must be able to support the weight of the refrigerator and its contents.

3. Make sure there are no adjacent heat sources such as a furnace vent, a hot water heater vent, etc.

4. If there is more than 1/2 inch between either side of the refrigerator and the inside of the enclosure:

- Fill the space with berglass insulation or add a bae to eliminate the excess clearance.

- Make sure that the rear of the batt-type insulation is between 18 - 19 inches from the face of the enclosure.

- Securely attach the batt-type insulation to the enclosure so that it remains in this position during refrigerator installation, if it

becomes wet, and in windy conditions.

Installation Manual 6

Install the Lower and Upper Vents

1. Using the following chart, decide which vents and rough opening (RO) sizes to use:

Certied Vent P/N RO Height RO Width

Upper Roof Exhaust Cap 622293 N/A N/A

Upper Roof Exhaust Vent 616319 24 in. 5 1/4 in.

Upper Exhaust & Lower Intake Plastic 621156 13 3/4 in. 21 1/2 in.

Lower Square Corner Intake 616010 9 3/4 in. 19 3/8 in.

2. Install the lower intake vent (See Art01602):

The lower intake vent is also the service access opening for the components

on the rear of the refrigerator.

Make sure the bottom of the opening of the lower intake vent is

even with or immediately below the oor level. This allows any

leaking propane gas to escape to the outside and not to collect at

oor level.

- Make sure the bottom of the opening of the lower intake vent [9] is even with or

immediately below the oor level.

- Align the lower intake vent vertically below the coils [10] and the condenser [11] of the

refrigerator.

3. Install the upper exhaust vent:

Make sure that no sawdust, insulation, or other construction debris is

on the refrigerator or in the enclosure. Debris can cause a combustion

hazard and prevent the refrigerator from operating correctly.

Tighten the screws of the upper roof exhaust cap to 10 inch-pounds max. Also

make sure that the air ow around the upper roof exhaust cap is not blocked

or decreased by other roof mounted features such as a luggage carrier, an air

conditioner, a solar panel, etc.

- If the design of the vehicle allows, install the roof exhaust vent [12] directly above the

condenser [11] of the refrigerator (See Art01676):

- Install a bae [13] to prevent stagnant hot air in the area [14] above the refrigerator.

- Make sure there is less than 1/4 inch clearance [15] between the bae and the

top of the refrigerator.

- Make sure the bae is the full width of the inside of the enclosure.

- If the design of the vehicle does not allow you to install the roof exhaust vent directly above the condenser [11] of the refrigerator

(See Art01677):

- Align the roof exhaust vent [12] above the condenser [11] of the refrigerator and move it inboard as necessary.

- Install two baes [13] to prevent stagnant hot air in the area [14] above the refrigerator.

- Make sure the baes are the full width of the inside of the enclosure.

Art01602

WARNING

CAUTION

NOTICE

Installation Manual 7

Art01676

Art01677

- Make sure that the baes are no more than 45° from vertical [20].

- Put one bae between the top rear edge of the refrigerator and the inside edge of the upper exhaust vent opening.

- Put the other bae between the outside edge of the upper exhaust vent opening and the side wall of the vehicle.

- If the depth of the enclosure is 24 inches or more and is less than 25 inches, no baes are necessary at the rear of the enclosure.

- If the depth of the enclosure is 25 inches or more and is less than 26 inches, add two baes [16] to the rear of the enclosure (See

Art01676 and Art01677).

- Put one bae 18 inches to 18 1/2 inches above the bottom of the enclosure [17] (4 1/4 inches to 4 3/4 inches above the top of

the lower intake vent opening REF) [18] .

- Put the other bae at the lowest edge of the condenser [11] of the refrigerator.

- Make sure that the baes are 1 inch or less [19] from the coils [10] and condenser [11] of the refrigerator.

- Make sure that the baes are the full width of the inside of the enclosure.

Installation Manual 8

- If the depth of the enclosure is more than 26 inches, install a wood or an aluminum or galvanized sheet solid box bae [21] in the

rear of the enclosure (See Art01681 and Art01682).

- Make sure that the bottom of the solid box bae is 18 inches to 18 1/2 inches above the bottom of the enclosure [17] (4 1/4

inches to 4 3/4 inches above the top of the lower intake vent opening REF) [18] .

- Make sure that the back of the solid box bae is perpendicular to the bottom of the enclosure.

- Make sure that the back of the solid box bae is either against the top of the enclosure or against the angled bae [13]

(depending on the vehicle design).

- Make sure that the solid box bae is one inch or less [19] from the coils [10] and condenser of the refrigerator.

- Make sure that the solid box bae is the full width of the inside of the enclosure.

Art01681

Art01682

Installation Manual 9

- If the design of the vehicle does not allow you to install a roof exhaust vent, install an upper

side-wall exhaust vent.

The refrigerator is 23.7 in. min. to 24.0 in. max. from the rear of the breaker

to the rear of the condenser [22] and 54.1 in. min. to 54.4 in. max. from the

bottom of the refrigerator to the bottom of the refrigerator condenser [23]

(See Art01678).

- Install the upper side-wall exhaust vent [24] (See Art01679 and Art01680).

- Make sure the distance [25] from the bottom of the enclosure to the top of the rough

opening for the upper exhaust vent is at least 62 inches.

- Align the upper exhaust vent horizontally above the lower intake vent [9] of the

refrigerator.

- To prevent stagnant hot air in the area above the refrigerator, install an aluminum or

galvanized steel sheet bae [13] between the top of the refrigerator and the top of

the upper exhaust vent.

- Make sure there is less than 1/4 inch clearance between the bae and the top

of the refrigerator [16] and that the bae overlaps the refrigerator 1 inch or

less.

- Make sure that the bae is against the wall of the vehicle at the top of the

upper exhaust vent and 1/4 inch or less from the top of the opening for the

upper exhaust vent [15].

- Make sure the bae is the full width of the inside of the enclosure

- When using an upper side-wall exhaust vent:

- If the depth of the enclosure is more than 24 inches and less than 26 inches [27], install a bent aluminum or galvanized steel

sheet bae [26] to the rear of the enclosure (See Art01679).

Art01678

Art01679

13 15 11

213

Art01680

1513

213

NOTICE

Installation Manual 10

Reverse the Door Swing-Nonmetal Doors (optional)

This refrigerator has cabinet hinges that allow you to change the direction the

door opens by moving the hinges on a diagonal to the opposite side. Reverse

the door swing before installing the refrigerator in the vehicle.

1. Pull o both the upper [40] and lower [128] trim pieces if they are already

installed (See Art01688 and Art01689).

2. Remove the doors (See Art01731):

- Remove the storage bins from the doors.

Do not mix the upper and lower hinge pins because they are

dierent.

- Remove and save the upper hinge pin [63] from each

door.

- Pull the door latch and remove each door from the

refrigerator.

- Make sure that the bend of the bae is the full width of the inside of the enclosure.

- Make sure that the bend of the bae is ush with the bottom edge of the upper intake vent door frame.

- Make sure that the top edge of the bae is 1/4 inch [213] below the bottom of the condenser and that there is 1/4 inch or

less clearance [15] between the rear of the condenser and the bae.

- If the depth of the enclosure is more than 26 inches [27], install a wood or an aluminum or galvanized steel sheet solid box

bae [21] between the lower intake vent and the upper exhaust vent (See Art01680).

- Make sure that the solid box bae is the full width of the inside of the enclosure.

- Make sure that the bottom of the solid box bae is 18 inches to 18 1/2 inches above the bottom of the enclosure [17] (4

1/4 inches to 4 3/4 inches above the top of the lower intake vent opening REF) [18] .

- Make sure that the back of the solid box bae is perpendicular to the bottom of the enclosure.

- Make sure that the horizontal top of the solid box bae is even with the bottom edge of the upper exhaust vent [24].

- Make sure that the horizontal top edge of the bae is 1/2 inch [213] or less below and 1/4 inch or less behind the lower

rear corner of the condenser.

- Make sure that there is 1/4 inch or less clearance [15] between the rear of the condenser and the bae.

For rear wall installations please refer to special instructions 620918 for additional required instructions.

211

128

208

Art01688

210

Art01689

NOTICE

Rear wall Installation

Installation Manual 11

3. Remove the upper mounting ange and the lower mounting

ange (See Art01683):

- Remove and save the four screws [41] from the upper

mounting ange [210] and from the lower mounting ange

[211].

4. Change the position of the cabinet hinges and the strike plate

(See Art00983 and Art01685):

- Remove and save the screws from the strike plate [65a].

- Remove and save the top and bottom of the three screws [41]

that are beside the strike plate.

- Do not remove the center screw.

- Put each of the outside cabinet hinges [250a] on the other side of the refrigerator [250b].

- Make sure that the oset of these hinges is positioned down on upper cabinet hinge and

up on the lower cabinet hinge.

- Attach each of these hinges with screws.

- Remove and save the screws from the center cabinet hinges [251a].

- Reverse each center hinge and put on the other side of the refrigerator [251b].

- Attach each of these hinges with screws.

- Remove and save the screw [41] from the front box [68] (See Art00983).

- Pull the front box away from the refrigerator and out from under the controls [69].

- Reverse the front box and put it on the opposite side of the controls.

- Attach the front box to the refrigerator with the screw [41] that was removed before.

- Put the strike plate on the opposite side of the refrigerator [65b].

- Put the two screws [41] into the holes that are beside the strike plate.

rt01731

Art01683

210

212

211

rt00983

Installation Manual 12

5. Change the position of the door handles (See Art01727):

- Remove the screw(s) [41] and door handle [10] from each door.

- Reverse each door handle and put the lower door handle on the upper door

and the upper door handle on the lower door.

- Attach each door handle with the screws.

6. Install the upper mounting ange and the lower mounting ange in the original

positions (See Art01683):

Make sure that both foam pads [212] remain in

position on each mounting ange to complete the

combustion seal. If the seal is not complete, exhaust

fumes can be present in the living area of the vehicle.

The breathing of exhaust fumes can cause dizziness,

nausea, or in extreme cases, death.

- Make sure that both foam pads [212] remain in position on each mounting

ange to complete the combustion seal.

- Attach the upper mounting ange [210] and the lower mounting ange [211]

with four screws [41].

The lower mounting ange has more bends than the upper

mounting ange.

- Securely tighten the screws.

7. Reinstall the doors (See Art01731):

- Turn the lower hinge pins into the lower cabinet hinges [67].

To prevent damage to the threads of the hinge pins, turn the

hinge pins by hand until tight and then tighten with a screwdriver.

Apply Loctite removable thread locker (blue) to the threads of the

hinge screws before assembly to prevent loosening during use.

Do not allow Loctite to contact any of the plastic surfaces of the

refrigerator because it can damage those surfaces.

- Put each door down onto the lower hinge pin.

- Align the holes in the upper hinges and hold in this position.

- Turn the upper hinge pin into the upper hinge [66] of each door.

- Tighten the hinge pins.

- Put the storage bins in the doors.

8. To install the upper and lower trim pieces refer to the “Install the Refrigerator” section of

this manual.

Art01685

250b

65a

251b

250a

251a

65b

250b

250a

Art01727

WARNING

CAUTION

NOTICE

Installation Manual 13

Reverse the Door Swing-Metal Doors (optional)

This refrigerator has door hinges that allow you to change the direction the door

opens by moving the hinges on a diagonal to the opposite side. Reverse the

door swing before installing the refrigerator in the vehicle.

1. Pull o both the upper [40] and lower [128] trim pieces if they are already

installed (See Art01688 and Art01689).

2. Remove the doors (See Art01684):

- Remove the storage bins from the doors.

- Remove and save both hinge pins [71] from each door.

- Remove and save both hinge bushings [74] from each door.

- Pull the door latch and remove each door away from the

refrigerator.

3. Remove the upper mounting ange and the lower

mounting ange (See Art01683):

- Remove and save the four screws [41] from the upper

mounting ange [212] and from the lower mounting

ange [211].

4. Change the position of the cabinet hinges and the strike

plate (See Art00983 and Art01685):

- Remove and save the screws from the strike plate [65a].

- Remove and save the top and bottom of the three screws

[41] that are beside the strike plate.

- Do not remove the center screw.

- Remove and save the screws [41] from the outside cabinet hinges [250a].

- Put each of these hinges on the other side of the refrigerator [250b].

- Make sure that the oset of these hinges is positioned down on upper cabinet hinge and up

on the lower cabinet hinge.

- Attach each of these hinges with screws.

- Remove and save the screws from the center cabinet hinges [251a].

- Reverse each center hinge and put on the other side of the refrigerator [251b].

- Attach each of these hinges with screws.

211

128

208

Art01688

210

Art01689

Art01684

250

251

Installation Manual 14

- Remove and save the screw [41] from the front box [68] (See

Art00983).

- Pull the front box away from the refrigerator and out from under

the controls [69].

- Reverse the front box and put it on the opposite side of the

controls.

- Attach the front box to the refrigerator with the screw [41] that

was removed before.

- Put the strike plate on the opposite side of the refrigerator

[65b].

- Put the two screws into the holes that are beside the strike

plate.

5. Change the position of the door handles and the door hinges

(See Art01695 and Art00985):

- Remove the plastic cap that is opposite the upper hinge of the

upper door.

- Remove the cap screw [72] from the door handle [70] and the

door hinges [73].

- Remove the round head screw(s) [41] and door handle from

each door.

- Remove the upper hinge of each door.

- Put each of these hinges on the other side of the door as the

lower hinge.

- Attach each of these hinges with the cap screws that were

removed from the other side.

- The recommended torque for each cap screw [72] is 35 in.-lbs.

- Remove the lower hinge of each door.

- Put each of these hinges on the other side of the door as the upper hinge.

- Attach each of these hinges with the cap screws that were removed from the other side.

- Reverse each door handle and put the lower door handle on the upper door and the upper

door handle on the lower door.

- Attach each door handle with a cap screw [72] and two screws [41].

- Put the plastic cap into the hole that is opposite the upper hinge of the upper door.

Art01683

210

212

211

rt00983

Installation Manual 15

6. Install the upper mounting ange and the lower mounting ange in the original

positions (See Art01683):

Make sure that both foam pads [212] remain in

position on each mounting ange to complete the

combustion seal. If the seal is not complete, exhaust

fumes can be present in the living area of the vehicle.

The breathing of exhaust fumes can cause dizziness,

nausea, or in extreme cases, death.

- Make sure that both foam pads [212] remain in position on each mounting

ange to complete the combustion seal.

- Attach the upper mounting ange [210] and the lower mounting ange [211]

with four screws [41].

The lower mounting ange has more bends than the upper

mounting ange.

- Securely tighten the screws.

7. Reinstall the doors (See Art01684):

- Make sure each hinge bushing [74] is in the correct position.

- Put each hinge bushing into the bottom side of each door hinge.

- Put each door in the position on the refrigerator.

To prevent damage to the threads of the hinge pins, turn

the hinge pins by hand until tight and then tighten with a

screwdriver.

Apply Loctite removable thread locker (blue) to the

threads of the hinge screws before assembly to prevent

loosening during use. Do not allow Loctite to contact any of the plastic surfaces of the refrigerator

because it can damage those surfaces.

- Align the hinges and put the hinge pins [71] into each door hinge.

- Tighten the hinge pins.

- Put the storage bins in the doors.

8. To install the upper and lower trim pieces refer to the “Install the Refrigerator” section of this manual

Art01685

250b

65a

251b

250a

251a

65b

250b

250a

Install Decorative Door Panels (non-metal door models)

The doors are made to accept decorative panels. The decorative panels must be 3/16 inch or less in thickness. Install

the decorative door panels in the refrigerator doors before installing the refrigerator in the vehicle.

- Make an upper door panel that is 21 19/32 inches wide x 14 17/32 inches high.

- Make a lower door panel that is 21 19/32 inches wide x 38 5/8 inches high.

- Pull the panel retainer [37] o each door (See Art00965).

- Push the decorative door panel [38] into the slots of the door [39].

- Push each panel retainer into the slot on the edge of the door.

Art00965

WARNING

NOTICE

CAUTION

NOTICE

Installation Manual 16

Install the Refrigerator

1. Put the refrigerator in position (See Art01687, Art01688, and Art01689):

Make sure the combustion seal [28] is not broken, is completely around the

refrigerator mounting anges, and is between the mounting anges and

the wall of the enclosure If the seal is not complete, exhaust fumes can be

present in the living area of the vehicle. The breathing of exhaust fumes can

cause dizziness, nausea, or in extreme cases, death.

Be careful when you put the refrigerator into position. The refrigerator has vacuum

insulating panels. If punctured, these panels lose insulation value which decreases

the cooling performance of the refrigerator.

- Push the refrigerator completely into the enclosure.

- Put two mounting screws [41] through the lower mounting ange on the front of the refrigerator and

into the enclosure wall.

- Put two mounting screws [41] through the upper mounting ange on the front of the refrigerator and

into the enclosure wall.

2. Install the upper and lower trim pieces:

These trim pieces are not the same. Make sure that the notch [20] in the upper and

lower trim pieces t around the upper and lower cabinet hinge.

- Align the tabs of each trim piece with the rectangular holes of each mounting ange.

- Push the lower trim piece [128] onto the front of the lower mounting

ange [211] until you feel both ends engage and hear a “snap” sound.

- Push the upper trim piece [40] onto the front of the upper mounting

ange [210] until you feel both ends engage and hear a “snap” sound.

- Put screws through mounting ange on the rear of the refrigerator and

into the oor.

Art01687

211

128

208

Art01688

210

Art01689

NOTICE

WARNING

Installation Manual 17

The ice maker is assembled to the refrigerators at the factory as optional equipment. If the refrigerator does not have a factory installed

ice maker, one can not be added to the refrigerator at a later time.

The refrigerator installer must connect a cold water supply line to the solenoid valve at the rear of the refrigerator. The following are

necessary to connect the icemaker:

- 1/4 in. OD copper tubing for the water supply line.

- 1/4 in. OD plastic tubing for the water supply line.

- 1/4 in. shut o valve in the water supply line. This should be easily accessible through the

lower intake vent.

Connect the water supply line:

Install a 1/4 in. OD water supply line [43] from the water shut o valve of the vehicle to the

solenoid water valve [44] at the rear of the refrigerator (See Art01014):

A brass compression nut [45], a brass sleeve, a plastic sleeve [46] , and a

brass insert [47] are supplied and attached to the rear of the refrigerator (See

Art01755).

- Put the compression nut and then the sleeve onto the water supply line [43].

- For copper tubing, use the brass sleeve.

- For plastic tubing, use the plastic sleeve [46].

- For plastic tubing with .040 in. wall thickness, also use the brass insert [47].

- Flush the water supply line until the water is clear.

- Put the tubing into the water valve until it is against the stop of the adapter.

- Tighten the compression nut by hand (hard nger tight).

- Using two wrenches, tighten the compression nut 1 ½ to 2 turns.

- Open the water shut o valve of the vehicle.

- Examine the connections for leaks.

Connect the Ice Maker (N109XIM, and N109XIMXX models)

Art01014

Connect the Electrical Components

AC Operation 120 volts AC voltage (132 volts max. - 108 volts min.)

12 volts DC control voltage (15.4 volts max. - 10.5 volts min.)

This refrigerator operates on these electrical sources. Operation out of these limits may damage the refrigerator’s electrical circuit

parts and will void the warranty.

The rear of the refrigerator cooling system has hot surfaces and sharp surfaces that can damage electrical

wiring. Make sure that there is a good clearance between all electrical wiring and the cooling system of the

refrigerator. Position any electrical wiring within the refrigerator enclosure opposite the burner side of the

refrigerator. Do not put any electrical wiring through the roof exhaust vent. Failure to correctly position

electrical wiring can result in electrical shock or re.

WARNING

NOTICE

Installation Manual 18

Connect the 120 volts AC supply:

Connect the AC power cord(s) only to a grounded three-prong receptacle. Do not remove the round ground prong

from any of the AC power cords. Do not use a two prong adapter or an extension cord with any of the AC power cords.

Operation of the refrigerator without correct ground can cause dangerous electrical shock or death if you are touching

the metal parts of the refrigerator.

Put the AC power cord(s) into a grounded three-prong receptacle:

- Make sure the receptacle is positioned within easy reach of the lower intake vent.

- Make sure the power cord(s) does not touch the burner cover, the ue pipe, or any hot component that could damage the insulation

of the power cord.

Connect the 12 volts DC supply:

As the distance from the vehicle battery to the refrigerator increases, the correct AWG wire size and fuse size also increases. If the

wire size is too small for the distance, a voltage drop occurs.

1. Determine the min. wire size and the max. fuse size to use:

If you use an incorrect wire size and/or fuse size, electrical re can result.

- Use a minimum of 18 AWG wire and a maximum 6 Amp fuse.

- If the wire size is larger than the min. size, use the correct fuse per RVIA A119.2 standard or local codes.

2. Install a fuse in DC power supply wires between the battery and the refrigerator:

- Put fuse as close to the battery as possible.

3. Connect the DC power supply wires (See Art00966):

- Attach a 1/4 inch Quick Connect terminal to each DC power supply wire.

Do not use the chassis of the refrigerator or the vehicle frame as one of

the conductors. Attach the DC power supply wires only to the battery and

the power board [49] of the refrigerator.

- Push the positive DC power wire [50] onto the power board terminal that is marked

12VDC.

- Push the DC ground wire [51] onto the power board terminal that is marked GND.

- Make sure each DC power supply wire is on the correct polarity terminal.

Art00966

121

NOTICE

WARNING

NOTICE

Installation Manual 19

Connect the Propane Gas Components

This refrigerator operates on propane gas at a pressure of 11 inches Water Column Propane.

The controls operate on 12 volts DC (10.5 volts min. - 15.4 volts max.). Operation out of these limits can damage the refrigerator

electrical circuit parts and will void the warranty

Connect the propane gas supply system:

Be very careful when working on or near the propane gas system.

- Do not smoke, or use an open ame near the propane gas system.

- Do not use an open ame to examine for leaks.

WARNING

Connect the Low Ambient Heater (optional)

Connect the low ambient heater wires to the 12 volts DC supply. The black

(+) wire of the low ambient heater is 16 AWG and the brown (-) wire is 18

AWG.

1. Cut the 12V input (+) wire behind the quick connect [269]; strip both ends

(See Art02316).

2. Solder the wires with the 16AWG black wire [266].

3. Wrap the soldered wires with black electrical tape [268]; BE SURE there

are no exposed strands.

4. Cut the 12V ground wire behind the quick connect [269]; strip both ends

(See Art02317).

5. Solder the wires with the 18AWG wire [267].

6. Wrap the soldered wires with black electrical tape [268] ; BE SURE there

are no exposed strands.

7. Connect 12V supply to the input wires.

This kit supplies DC voltage to the heater any time the

ambient temperature is low enough. Extended storage

during cold weather will drain the vehicle batteries. To

prevent battery drain, remove the 3 amp fuse from the low

ambient heater.

Art02316

268

269

266

Art02317

268

269

267

NOTICE

Installation Manual 20

- Do not connect the refrigerator to the propane gas tank without a pressure regulator between them.

- To avoid a propane gas leak, always use two wrenches to tighten or loosen the propane gas supply line connections.

- Leaking propane gas can ignite or explode and result in dangerous personal injury or death.

Connect the gas supply line to the refrigerator:

- Make sure that all tubing and ttings obey all local, state, and national codes about size and type.

- Make sure that all exible metal connectors obey the current CAN1-6.10 Standard.

- Make sure that the materials used for the gas supply line obey both the current ANSI A 119.2 (NFPA 1192) and CSA Z240

Standards on Recreational Vehicles. Norcold recommends the use of 3/8 inch copper tubing as the gas supply line and requires a

3/8 inch SAE (UNF 5/8-18) male are tting as the connection to the refrigerator.

- Put the propane gas supply line up through the oor of the enclosure.

- Make sure the hole through the oor is large enough allow clearance for the gas supply line.

- Put a weather resistant seal (grommet, sealant, etc.) around the gas supply line where it goes through the oor to prevent vibration

and abrasion.

- Make sure that the propane gas supply line does not interfere with removal of the burner box cover or block the door opening of the

burner box cover.

- To prevent vibration and abrasion, make sure that the gas supply line is not against anything in the enclosure.

- Attach the gas supply line to the combination gas valve of the refrigerator.

Examine the gas supply system for leaks:

Do not allow the leak detecting solution to touch the electrical components. Many liquids are electrically

conductive and can cause electrical shorts and in some cases, re.

Use a leak detecting solution to examine the gas supply line and all propane gas connections for leaks.

If you use compressed air for the test:

- The pressure of the compressed air at the manual shut o valve of the refrigerator must not be more than 1/2 psig (14 inches Water

Column).

- If the pressure of the compressed air is more than 1/2 psig (14 inches Water Column), remove the gas supply line from the

combination gas valve of the refrigerator before the test.

- If the pressure of the compressed air is equal to or less than 1/2 psig (14 inches Water Column), close the manual shut o valve of

the refrigerator before the test.

WARNING

La page charge ...

Norcold N1095 Guide d'installation

Marque: Norcold

Modèle: N1095

Catégorie: Cheminées

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Norcold N1095 Installation guide

Norcold N1095 Guide d'installation

Norcold N1095 Guide d'installation

dans d''autres langues

Documents connexes