WHAT YOU NEED
•
Screwdriver
• Wire Cutters
• Wiring Supplies as Specified
by Electrical Code
• 1x 60W E26 A19 bulb
INSTALLATION INSTRUCTIONS
WHAT WE PROVIDE
•
Mounting Hardware
• 10” Wire with lamp holder
• Metal shade
COLLECTION
1
CERTIFICATION: cULus DRY
NO. 23776
NOSTALGIA
23776
APPLICATION MODEL NO.
Pendant Fixture
IMPORTANT SAFETY INSTRUCTIONS
MESURES DE SECURITE A RESPECTURE
Before assembling your ACCESS LIGHTING fixture, please make sure that
you carefully read through this instruction sheet. Save this instruction sheet
and refer to it when additions to or changes in the fixture
configuration are made.
Lisez attentivement ce manuel d’instructions. Enregistrer cette feuille
d'instructions et de s'y référer lorsque les ajouts ou changements dans
la configuration de montage sont faites.
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH
CIRCUIT CONDUCTOR.
CONSULTER UN ELECTRICIEN QUALIFIE POUR VOUS ASSURER QUE LES
CONDUCTEURS DE LA DERIVATION SONT ADEQUATS
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONTSTRUCTION
AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION PERTINENT,
PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET SON FONCTIONNEMENT
AINSI QUE LES RISQUES INHERENTS
NOTE: The important safeguards and instructions that appear in this
manual are not meant to cover all possible conditions and situations
that may occur. It must be understood that common sense, caution and
care, are factors that can’t be built into any product. These factors must
be supplied by the person(s) caring for and operating the fixture.
Read all instructions
Do not install this fixture in hazardous locations.
N'installez pas cet appareil dans des emplacements dangereux.
Do not install any fixture assembly closer than 6 inches from any
curtain or similar combustible material.
Laisser une distance d’au moins 6 pouces entre ce luminaire et la toute
surface combustible.
"WARNING Risk of Fire and Electric Shock."
“CAUTION: Risque d’ Incendie et de Choc Electriques.”
GENERAL INFORMATION
All electrical connections must be in accordance with all ordinances,
Local and the U.S. National Electrical Codes (NEC). These fixtures are
intended for mounting to a standard 4” metal octagon outlet box.
The box must be directly supported by the building structure and U.L.
Recognized.
STEP BY STEP INSTRUCTIONS
Before starting your installation disconnect the Power by turning off the
Circuit Breaker or by removing the fuse at the fuse box. Just turning the
light off at the light switch is not sufficient to prevent electrical shock.
MAKE WIRE CONNECTION
If there is an existing fixture remove it.
Expose the supply wires from the J-box.
Gently pull the supply wires through the hole in the
crossbar plate. Connect the black supply wire to
the black fixture wire. Secure with the supplied wire nuts.
Connect the white supply wire to the white fixture wire.
Secure with the supplied wire nuts. Attach the green
J-Box wire around green hexagonal head screw or
connect it to the green supply grounding wire of the
fixture. Secure all wires with electrical tape
(not supplied). Tuck all wires carefully into the J-Box.
1
WHAT YOU NEED
•
Screwdriver
• Wire Cutters
• Wiring Supplies as Specified
by Electrical Code
• 1x 60W E26 A19 bulb
2
4
2
CERTIFICATION: cULus DRY NO.
23776
3
MOUNT CROSSBAR
Install the crossbar and mount it to the J-Box with
the supplied screws.
MOUNT THE CANOPY AND INSERT
THE BULB
Fit the canopy up to the crossbar and secure with
the supplied screw nut.
Insert the bulb.
MAXIMUM WATTAGE 60W.
DO NOT EXCEED THE RECOMMENDED WATTAGE AS
STATED ON THE WARNING LABEL AND
INSTRUCTION SHEETS.
Please ensure that the fitting is cool and
switched off before replacing the bulb.
DO NOT use bulbs that exceed the
maximum wattage, stated on caution label.
CAUTION
RESTORE THE ELECTRICITY AND
CHECK THE OPERATION OF YOUR
NEW ACCESS LIGHTING FIXTURE
N
L
GND
-
1
-
2
Access Lighting Nostalgia 23766 Guide d'installation
- Taper
- Guide d'installation
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Access 28030-1C-BS/AMB Mode d'emploi
-
Access Lighting 50184-BS/OPL Guide d'installation
-
Access Lighting 20292LEDDLP-SAT/FST Manuel utilisateur
-
-
-
-
-
-
-
