Electrolux EFME617STT Guide d'installation

EN FRONT LOAD DRYER

FR SÉCHEUSE Á CHARGEMENT FRONTAL

ES SECADORA DE CARGA FRONTAL

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION

INSTRUCCIONES DE INSTALACIÓN

A04173601A August 2015

22 Important Safety Instructions

Recognize safety symbols, words

and labels

Safety items throughout this manual are

labeled with a WARNING or CAUTION

based on the risk type as described:

• Destroy the carton and plastic bags after the dryer is unpacked. Children might use them for play.

Cartons covered with rugs, bedspreads, or plastic sheets can become airtight chambers causing

suﬀ ocation. Place all materials in a garbage container or make materials inaccessible to children.

• Clothes dryer installation and service must be performed by a qualiﬁ ed installer, service agency or

the gas supplier.

• Install the clothes dryer according to the manufacturer’s instructions and local codes.

• The electrical service to the dryer must conform with local codes and ordinances and the latest

edition of the National Electrical Code, ANSI/NFPA 70, or in Canada, the Canadian electrical

code C22.1 part 1.

• The gas service to the dryer must conform with local codes and ordinances and the latest edition

of the National Fuel Gas Code ANSI Z223.1/NFPA 54, or in Canada, thw Natural Gas and Propane

Installation Code, CSA B149.1. An individual manual shut-oﬀ valve must be installed within 6 ft (1.83

m) of the dryer in accordance with the National Fuel Gas Code, ANSI Z223.1/NFPA 54.

• The dryer is designed under ANSI Z 21.5.1 or ANSI/UL 2158 - CAN/CSA C22.2 No. 112 (latest edi-

tions) for HOME USE only. This dryer is not recommended for commercial applications such as

restaurants, beauty salons, etc.

• Do not install a clothes dryer with ﬂ exible plastic or ﬂ exible foil venting material. Flexible venting

materials are known to collapse, be easily crushed and trap lint. These conditions will obstruct

clothes dryer airﬂ ow and increase the risk of ﬁ re.

• Do not stack a dryer on top of washer already installed on pedestal. Do not stack washer on top

of dryer. Do not stack washer on top of another washer.

• The instructions in this manual and all other literature included with this dryer are not meant to

cover every possible condition and situation that may occur. Good safe practice and caution

MUST be applied when installing, operating and maintaining any appliance.

Save these instructions for future reference.

This symbol alerts you to situations that may

cause bodily injury or property damage.

Table of contents

This symbol alerts you to situations that may

cause serious body harm, death or property

damage.

WARNING

For your safety the information in this manual must be followed to minimize the risk of ﬁ re or

explosion or to prevent property damage, personal injury or loss of life. Do not store or use

gasoline or other ﬂ ammable vapors and liquids in the vicinity of this or any other appliance.

Important Safety Instructions .....................................2

Installation Requirements ........................................ 3-9

Installation Instructions ..........................................10-17

Reversing Door ..........................................................18-19

Options ............................................................................. 20

WARNING  RISK OF FIRE

Read all of the following instructions before installing and using this appliance:

3

Installation Requirements

Adjustable

pliers

4 inch, rigid metal or

semi-rigid metal exhaust duct work

4 inch rigid metal or

Adjustable

wrench

Metal foil tape

(not duct tape)

External

vent hood

or

Carpenter’s level

Phillips, straight, &

square bit screwdrivers

Optional universal

accessory

wrench

Pipe wrench

for gas

supply

gas line

shutoff valve

(gas dryer)

or

LP-resistant

thread tape

(for natural gas

or LP supply)

½” NPT union flare

adapters (x2) and

flexible gas supply line

(gas dryer)

3-wire or 4-wire

240 volt cord kit

(electric dryer)

4 in.

(10.2 cm)

clamp

Tools and materials needed for installation:

Please read and save this

guide

Thank you for choosing Electrolux, the premium

brand in home appliances. These Installation

Instructions are part of our commitment to

customer satisfaction and product quality

throughout the life of your new appliance.

Questions?

Installation Checklist

240v Electric Supply (Electric Dryer)

 Approved NEMA 10-30 or 14-30 service

cord with all screws tight on terminal

block

 Approved strain relief installed

 Terminal access cover installed before

initial operation

Door Reversal

 Follow detailed instructions in this guide

 Test hinge and latch for function

Electrical Power

 House power turned on

 Dryer plugged in

Final Checks

 Installation Instructions and Use and

Care Guide read thoroughly

 Door latches and drum tumbles when

cycle starts

 Registration card sent in

Exhaust Venting

 Free-ﬂ owing, clear of lint buildup

 4 inch (102 mm) rigid or semi-rigid ducting

of minimal length and turns

 NO foil or plastic venting material

 Approved vent hood exhausted to

outdoors

Leveling



Dryer is level, side-to-side and front-to-

back

 Cabinet is setting solid on all corners

Gas Supply (Gas Dryer)

 Manual shutoﬀ valve present in supply

 All connections sealed with approved

sealer and wrench tight

 Conversion kit for LP system

 Gas supply turned on

 No leaks present at all connections -

check with soapy water, NEVER check with

ﬂ ame

For toll-free telephone support in the U.S.:

1-877-4ELECTROLUX (1-877-435-3287) and in

Canada: 1-800-265-8352.

For online support and product information visit

www.electroluxappliances.com.

WARNING

FIRE HAZARD

●Failure to follow safety warnings exactly

could result in serious injury, death, or

property damage.

●Do not install a booster fan in dryer exhaust

duct.

●Install all clothes dryers in accordance with

the installation instructions in this manual.

4Installation Requirements

Electrical system requirements

ELECTRICAL REQUIREMENTS FOR ELECTRIC

DRYER:

CIRCUIT - Individual 30 amp. branch circuit

fused with 30 amp. time delay fuses or circuit

breakers. Use separately fused circuits for

washer and dryer. DO NOT operate a washer

and a dryer on the same circuit.

POWER SUPPLY - 3-wire or 4-wire, 120/240 volt,

single phase, 60 Hz, Alternating Current.

3-WIRE POWER SUPPLY CORD (not supplied)

OUTLET RECEPTACLE - NEMA 14-30R

receptacle to be located so the power supply

cord is accessible when the dryer is in the

installed position.

GROUNDING CONNECTION - See “Grounding

requirements” in Electrical Installation section.

OUTLET RECEPTACLE - NEMA 10-30R

receptacle to be located so the power supply

cord is accessible when the dryer is in the

installed position.

GROUNDING CONNECTION - See “Grounding

requirements” in Electrical Installation section.

The dryer MUST employ a 3-conductor power

supply cord NEMA 10-30 type SRDT rated at

240 volt AC minimum, 30 amp, with 3 open

end spade lug connectors with upturned

ends or closed loop connectors and marked

for use with clothes dryers. For 3-wire cord

connection instructions see ELECTRICAL

CONNECTIONS FOR A 3-WIRE SYSTEM.

4-WIRE POWER SUPPLY CORD (not supplied)

The dryer MUST employ a 4-conductor

power supply cord NEMA 14-30 type SRDT

or DRT (as required) rated at 240 volt AC

minimum, 30 amp, with 4 open end spade

lug connectors with upturned ends or closed

loop connectors and marked for use with

clothes dryers. For 4-wire cord connection

instructions see ELECTRICAL CONNECTIONS

FOR A 4-WIRE SYSTEM.

ELECTRICAL REQUIREMENTS FOR GAS DRYER:

CIRCUIT - Individual, properly polarized and

grounded 15 amp. branch circuit fused with 15

amp. time delay fuse or circuit breaker.

POWER SUPPLY - 2-wire, with ground, 120 volt,

single phase, 60 Hz, Alternating Current.

POWER SUPPLY CORD - The dryer is equipped

with a 120 volt 3-wire power cord.

GROUNDING CONNECTION - See “Grounding

requirements” in Electrical Installation section.

Grounding type

wa

ll receptacl

ll receptacle

Po

wer cord with

3-prong

gr

ounded plug

Do not,

under

an

y cir

cumstances,

cut,

remo

ve

ve,

or b

ypass th

ypass the

gr

ounding pr

ong.

3-wire receptacle

(NEMA type 10-30R)

4-wire receptacle

(NEMA type 14-30R)

NOTE

Because of potentially inconsistent voltage

capabilities, the use of this dryer with power

created by gas powered generators, solar

powered generators, wind powered generators

or any other generator other than the local utility

company is not recommended.

NOTE

Dryers manufactured for sale in Canada have

factory-installed, 4-wire power supply cord

(NEMA 14-30).

NOTE

A 120/208 volt, single phase, 60 Hz, Alternating

Current supply may be used on dryers marked

for use on the rating plate.

IMPORTANT

This dryer is internally grounded to neutral un-

less it was manufactured for sale in Canada.

Only a 4-conductor cord shall be used when

the appliance is installed in a location where

grounding through the neutral conductor is

prohibited. Grounding through the neutral link

is prohibited for: (1) new branch circuit installa-

tions, (2) mobile homes, (3) recreational ve-

hicles, and (4) areas where local codes do not

permit grounding through the neutral.

5

Installation Requirements

Gas supply requirements

Exhaust system requirements

If your present system is made up of plastic duct

or metal foil duct, replace it with a rigid or semi-

rigid metal duct. Also, ensure the present duct is

free of any lint prior to installing dryer duct.

Use only 4 inch (102 mm) diameter (minimum)

rigid or ﬂ exible metal duct and approved vent

hood which has a swing-out damper(s) that

open when the dryer is in operation. When the

dryer stops, the dampers automatically close to

prevent drafts and the entrance of insects and

rodents. To avoid restricting the outlet, maintain

a minimum of 12 inches (30.5 cm) clearance

between the vent hood and the ground or any

other obstruction.

CORRECT

INCORRECT

The following are speciﬁ c requirements

for proper and safe operation of your

dryer.

1. Installation MUST conform with local codes,

or in the absence of local codes, with the

National Fuel Gas Code, ANSI Z223.1 (latest

edition).

2. The gas supply line should be 1/2 inch (1.27

cm) pipe.

3. If codes allow, ﬂ exible metal tubing may be

used to connect your dryer to the gas supply

line. The tubing MUST be constructed of

stainless steel or plastic-coated brass.

4. The gas supply line MUST have an individual

shutoﬀ valve installed in accordance with the

B149.1, Natural Gas and Propane Installation

Code.

5. A 1/8 inch (0.32 cm) N.P.T. plugged tapping,

accessible for test gauge connection, MUST

be installed immediately upstream of the gas

supply connection to the dryer.

6. The dryer MUST be disconnected from the

gas supply piping system during any pressure

testing of the gas supply piping system at test

pressures in excess of 1/2 psig (3.45 kPa).

7. The dryer MUST be isolated from the gas

supply piping system during any pressure

testing of the gas supply piping system at test

pressures equal to or less than 1/2 psig (3.45

kPa).

8. Connections for the gas supply must comply

with the Standard for Connectors for Gas

Appliances, ANSI Z21.24/CSA 6.10.

WARNING

EXPLOSION HAZARD

Uncoated copper tubing will corrode when

subjected to natural gas, causing gas leaks.

Use ONLY black iron, stainless steel, or plastic-

coated brass piping for gas supply.

WARNING

FIRE HAZARD

Failure to follow these instructions can create

excessive drying times and ﬁ re hazards.

WARNING

FIRE HAZARD

Do not install a clothes dryer with ﬂ exible

plastic or metal foil venting materials. Flexible

venting materials are known to collapse, be

easily crushed and trap lint. These conditions

will obstruct clothes dryer airﬂ ow and increase

the risk of ﬁ re.

6Installation Requirements

The dryer must be connected to an exhaust

outdoors. Regularly inspect the outdoor exhaust

opening and remove any accumulation of lint

around the outdoor exhaust opening and in the

surrounding area.

EXHAUST DIRECTION

Directional exhausting can be accomplished

by installing a quick-turn 90° dryer vent elbow

directly to exhaust outlet of dryer. Dryer vent

elbows are available through your local parts

distributor or hardware store.

Exhaust system requirements, continued

Number of 90° turns

MAXIMUM LENGTH

of 4” (102 mm) Rigid Metal Duct

VENT HOOD TYPE

(Preferred)

4”

(10.2 cm) louvered

2.5”

(6.35 cm)

0 125 ft. (38 m) 110 ft. (33.5 m)

1 115 ft. (35 m) 100 ft. (30.5 m)

2 105 ft. (32 m) 90 ft. (27.5 m)

3 95 ft. (29 m) 80 ft. (24.5 m)

4 85 ft. (26 m) 70 ft. (21.5 m)

NOTE

Use of 90° quick-

turn elbow required

to meet minimum

installation depth.

WARNING

FIRE HAZARD

A clothes dryer must be exhausted outdoors.

Do not exhaust dryer into a chimney, a wall,

a ceiling, an attic, a crawl space or any

concealed space of a building. A clothes

dryer produces combustible lint. If the dryer

is not exhausted outdoors, some ﬁ ne lint

will be expelled into the laundry area. An

accumulation of lint in any area of the home

can create a health and ﬁ re hazard.

WARNING

FIRE HAZARD

Exceeding the length of duct pipe or number

of elbows allowed in the “MAXIMUM LENGTH”

charts can cause an accumulation of lint in

the exhaust system. Plugging the system could

create a ﬁ re hazard, as well as increase drying

times.

WARNING

FIRE HAZARD

●Do not allow combustible materials (for

example: clothing, draperies/curtains, paper)

to come in contact with exhaust system.

The dryer MUST NOT be exhausted into a

chimney, a wall, a ceiling, or any concealed

space of a building which can accumulate

lint, resulting in a ﬁ re hazard.

●Do not screen the exhaust ends of the

vent system, or use any screws, rivets or

other fasteners that extend into the duct

to assemble the exhaust system. Lint can

become caught in the screen, on the

screws or rivets, clogging the duct work and

creating a ﬁ re hazard as well as increasing

drying times. Use an approved vent hood

to terminate the duct outdoors, and seal all

joints with metal foil tape. All male duct pipe

ﬁ ttings MUST be installed downstream with

the ﬂ ow of air.

WARNING

FIRE HAZARD

●Do not install ﬂ exible plastic or ﬂ exible foil

venting material.

●If installing semi-rigid venting, do not exceed

8 ft. (2.4 m) duct length.

See also CLEARANCE

REQUIREMENTS on the

next page.

7

Installation Requirements

In installations where the exhaust system is not

described in the charts, the following method

must be used to determine if the exhaust system

is acceptable:

Exhaust system requirements, continued

CORRECT INCORRECT

1. Connect an inclined or digital manometer

between the dryer and the point the exhaust

connects to the dryer.

2. Set the dryer timer and temperature to air ﬂ uﬀ

(cool down) and start the dryer.

3. Read the measurement on the manometer.

4. The system back pressure MUST NOT be

higher than 1.0 inch of water column. If the

system back pressure is less than 1.0 inch of

water column, the system is acceptable. If

the manometer reading is higher than 1.0 inch

of water column, the system is too restrictive

and the installation is unacceptable.

Although vertical orientation of the exhaust

system is acceptable, certain extenuating

circumstances could aﬀ ect the performance of

the dryer:

●Only the rigid metal duct work should be

used.

●Venting vertically through a roof may expose

the exhaust system to down drafts causing

an increase in vent restriction.

●Running the exhaust system through an

uninsulated area may cause condensation

and faster accumulation of lint.

●Compression or crimping of the exhaust

system will cause an increase in vent

restriction.

●The exhaust system should be inspected and

cleaned a minimum of every 18 months with

normal usage. The more the dryer is used,

the more often you should check the exhaust

system and vent hood for proper operation.

Manufactured or mobile home installation

1. Installation MUST conform to current

Manufactured Home Construction & Safety

Standard, Title 24 CFR, Part 32-80 (formerly

the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD Part

280) or Standard CAN/CSAZ240 MH.

2. Dryer MUST be exhausted outside (outdoors,

not beneath the mobile home) using metal

ducting that will not support combustion.

Metal ducting must be 4 inches (10.16 cm) in

diameter with no obstructions. Rigid metal duct

is preferred.

3. If dryer is exhausted through the ﬂ oor and

area beneath the mobile home is enclosed,

the exhaust system MUST terminate outside

the enclosure with the termination securely

fastened to a non-combustible portion of the

mobile home structure.

4. Refer to previous sections in this guide for

other important exhaust venting system

requirements.

5. When installing a gas dryer into a mobile

home, a provision must be made for outside

make up air. This provision is to be not less

than twice the area of the dryer exhaust

outlet.

6. Installer MUST anchor this (1) dryer or (2)

dryer mounted on pedestal to the ﬂ oor with

approved Mobile Home Installation Kit - P/N

137067200.

Install male ﬁ ttings in correct direction:

WARNING

FIRE HAZARD

Do not install the dryer where gasoline or

other ﬂ ammables are kept or stored. If the

dryer is installed in a garage, it must be a

minimum of 18 inches (45.7 cm) above the ﬂ oor.

Failure to do so can result in death, explosion,

ﬁ re or burns.

8Installation Requirements

MIN INSTALLATION CLEARANCES - Inches (cm)

SIDES REAR TOP FRONT

Alcove 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a

Under-

Counter 0” (0 cm) 0” (0 cm)* 0” (0 cm) n/a

Closet 0” (0 cm) 0” (0 cm)* 0” (0 cm) 1” (2.5 cm)

Clearance requirements

60 sq. in.

(387.1cm²)

3”

(7.6cm)

60 sq. in.

(387.1cm²)

3”

(7.6cm)

INSTALLATION IN A RECESS OR CLOSET

1. A dryer installed in a bedroom, bathroom,

recess or closet, MUST be exhausted

outdoors.

2. No other fuel burning appliance shall be

installed in the same closet as the gas dryer.

3. Your dryer needs the space around it for

proper ventilation.

DO NOT install your dryer in a closet with a

solid door.

4. Closet door ventilation required: A minimum

of 120 square inches (774.2 cm²) of opening,

equally divided at the top and bottom of

the door, is required. Openings should be

located 3 inches (7.6 cm) from bottom and

top of door. Openings are required to be

unobstructed when a door is installed. A

louvered door with equivalent air openings

for the full length of the door is acceptable.

closet door

* F

or other than straight back venting, a quick-turn

90° dryer vent elbow must be installed to achieve

0” (0 cm) installation.

IMPORTANT

DO NOT INSTALL YOUR DRYER:

1. In an area exposed to dripping water or

outside weather conditions.

2. In an area where it will come in contact with

curtains, drapes, or anything that will obstruct

the ﬂ ow of combustion and ventilation air.

3. On carpet. Floor MUST be solid with a maxi-

mum slope of 1 inch (2.5 cm).

NOTE

To achieve an installation with 0” (0 cm)

clearance for the back of the dryer (for other

than straight back venting), a quick-turn 90°

dryer vent elbow must be installed as described

previously in this manual.

0”

(0 cm)

0”

(0 cm)

1”

(2.5 cm)

0”

(0 cm)

9

Installation Requirements

Dryer dimensions

*Connection of water inlet hose on steam dryer adds 3/4 in. (2 cm) to installation depth.

1Power supply cord length on gas dryer or electric Canadian dryer approximately 60 inches (152.5 cm).

2Drain hose length on washer approximately 59 inches (150 cm).

3Power supply cord length on washer approximately 60 inches (152.5 cm).

electrical

supply on

rear of unit1

gas supply

pipe on rear

of gas unit

centerline

height of

rear vent

53.5” (136 cm)*

to clear open door

31.5” (79.5 cm)*

to front of closed door 27.0”

(68.5 cm)

13.5”

(34.5 cm)

to center of

rear vent

ﬂ oor line

freestand dryer

on ﬂ oor

dryer mounted on

optional pedestal

38.0”

(96.5 cm)

53.25”

(135.5 cm)

17.0”

(43 cm)

19.0”

(48 cm)

3.7”

(9.5 cm)

1.5”

(4 cm)

3.75”

(9.5 cm)

electrical

supply on

rear of unit1

gas supply

pipe on rear

of gas unit

centerline

height for

rear vent

53.5” (136 cm)*

to clear open door

31.5” (79.5 cm)*

to front of closed door

75.75”

(192.5 cm)

41.0”

(105 cm)

39.0”

(99 cm)

water supply

connection on

rear of unit

drain hose on

rear of unit2

power cord on

rear of unit3

ﬂ oor line

10 Installation Instructions

Electrical installation

NOTE

Dryers operating on 208 volt power supply will

have longer drying times than dryers operating

on 240 volt power supply.

The following are speciﬁ c requirements for

proper and safe electrical installation of your

dryer. Failure to follow these instructions can

create electrical shock and/or a ﬁ re hazard.

Grounding requirements - Electric dryer (USA)

For a grounded, cord-connected dryer:

1. The dryer MUST be grounded. In the event

of a malfunction or breakdown, grounding

will reduce the risk of electrical shock by

providing a path of least resistance for

electrical current.

2. After you purchase and install a 3 wire or 4

wire power supply cord having an equipment-

grounding conductor and a grounding plug

that matches your wiring system, the plug

MUST be plugged into an appropriate, copper

wired receptacle that is properly installed and

grounded in accordance with all local codes

and ordinances. If in doubt, call a licensed

electrician.

3. DO NOT modify the plug you’ve installed

on this appliance. If it will not ﬁ t the outlet,

have a proper outlet installed by a qualiﬁ ed

electrician.

For a permanently connected dryer:

1. The dryer MUST be connected to a grounded

metal, permanent wiring system; or an

equipment grounding conductor must be run

with the circuit conductors and connected to

the equipment-grounding terminal or lead on

the appliance.

WARNING

ELECTRICAL SHOCK HAZARD

Improper connection of the equipment

grounding conductor can result in a risk

of electrical shock. Check with a licensed

electrician if you are in doubt as to whether

the appliance is properly grounded.

WARNING

ELECTRICAL SHOCK HAZARD

●This appliance MUST be properly grounded.

Electrical shock can result if the dryer is not

properly grounded. Follow the instructions in

this manual for proper grounding.

●Do not use an extension cord with this dryer.

Some extension cords are not designed to

withstand the amounts of electrical current

this dryer utilizes and can melt, creating

electrical shock and/or ﬁ re hazard. Locate

the dryer within reach of the receptacle for

the length power cord to be purchased,

allowing some slack in the cord. Refer to the

pre-installation requirements in this manual

for the proper power cord to be purchased.

WARNING

ELECTRICAL SHOCK HAZARD

●A U.L.-approved strain relief must be

installed onto power cord. If the strain relief

is not attached, the cord can be pulled

out of the dryer and can be cut by any

movement of the cord, resulting in electrical

shock.

●Do not use an aluminum wired receptacle

with a copper wired power cord and plug

(or vice versa). A chemical reaction occurs

between copper and aluminum and can

cause electrical shorts. The proper wiring

and receptacle is a copper wired power

cord with a copper wired receptacle.

11

Installation Instructions

Grounding requirements - Electric dryer (Canada)

Grounding type

wa

ll receptacl

ll receptacle

Po

wer cord with

3-prong

gr

ounded plug

Do not,

under

an

y cir

cumstances,

cut,

remo

ve

ve,

or b

ypass th

ypass the

gr

ounding pr

ong.

Grounding requirements - Gas dryer (USA and Canada)

For a grounded, cord-connected dryer:

1. The dryer MUST be grounded. In the event

of a malfunction or breakdown, grounding

will reduce the risk of electrical shock by

providing a path of least resistance for

electrical current.

2. Since your dryer is equipped with a power

supply cord having an equipment-grounding

conductor and a grounding plug, the plug

must be plugged into an appropriate outlet

that is properly installed and grounded

in accordance with all local codes and

ordinances. If in doubt, call a licensed

electrician.

3. DO NOT modify the plug provided with this

appliance. If it will not ﬁ t the outlet, have

a proper outlet installed by a qualiﬁ ed

electrician.

1. The dryer is equipped with a three-prong

(grounding) plug for your protection against

shock hazard and should be plugged directly

into a properly grounded three-prong

receptacle.

2. The plug must be plugged into an

appropriate outlet that is properly installed

and grounded in accordance with all local

codes and ordinances. If in doubt, call a

licensed electrician.

3. DO NOT modify the plug provided with this

appliance. If it will not ﬁ t the outlet, have

a proper outlet installed by a qualiﬁ ed

electrician.

WARNING

ELECTRICAL SHOCK HAZARD

Improper connection of the equipment

grounding conductor can result in a risk

of electrical shock. Check with a licensed

electrician if you are in doubt as to whether

the appliance is properly grounded.

12

Electrical connection (non-Canada) - 3 wire cord

Installation Instructions

1. Turn oﬀ power supply to outlet.

2. Remove the screw securing the terminal

block access cover in the lower corner on

the back of the dryer.

3. Install a UL-approved strain relief

according to the power cord/strain relief

manufacturer’s instructions in the power

cord entry hole below the access panel. At

this time, the strain relief should be loosely

in place.

4. Thread an UNPLUGGED, UL-approved, 30

amp. power cord, NEMA 10-30 type SRDT,

through the strain relief.

5. Attach the power cord neutral (center wire)

conductor to the SILVER colored center

terminal on the terminal block. Tighten the

screw securely.

6. Attach the remaining two power cord outer

conductors to the outer, BRASS colored

terminals on the terminal block. Tighten both

screws securely.

3-wire receptacle

(NEMA type 10-30R)

Internal ground

(GREEN screw)

Install

UL-approved

strain relief here

Terminal screw

recovery slot

Line 1

(BRASS terminal)

Neutral

(SILVER terminal)

Line 2

(BRASS terminal)

Access cover

screw

Terminal

block

Neutral

(center wire)

30 AMP

NEMA 10-30

7. Follow manufacturer’s guidelines for ﬁ rmly

securing the strain relief and power cord.

8. Reinstall the terminal block cover.

DO NOT remove

internal ground in

a 3-wire system!!

Neutral

terminal

NOTE

If a terminal screw falls during cord installation,

it can be retrieved in the terminal screw

recovery slot below the access panel.

WARNING

ELECTRICAL SHOCK HAZARD

Do not make a sharp bend or crimp wiring/

conductor at connections.

WARNING

ELECTRICAL SHOCK HAZARD

Failure to disconnect power source before

servicing could result in personal injury or even

death.

IMPORTANT

If moving dryer from a 4-wire system and install-

ing it in a 3-wire system, move the internal ground

from the center terminal back to the GREEN

screw next to the terminal block.

13

Installation Instructions

Electrical connection (non-Canada) - 4 wire cord

Internal ground

(GREEN screw)

Install

UL-approved

strain relief here

Terminal screw

recovery slot

Line 1

(BRASS terminal)

Neutral

(SILVER terminal)

Line 2

(BRASS terminal)

Access cover

screw

Terminal

block

4-wire receptacle

(NEMA type 14-30R)

1. Turn oﬀ power supply to outlet.

2. Remove the screw securing the terminal block

access cover in the lower corner on the back

of the dryer.

3. Install a UL-approved strain relief

according to the power cord/strain relief

manufacturer’s instructions in the power

cord entry hole below the access panel. At

this time, the strain relief should be loosely

in place.

4. Thread an UNPLUGGED, UL-approved, 30

amp. power cord, NEMA 14-30 type DRT or

SRDT, through the strain relief.

5. Disconnect the internal (WHITE) dryer

harness ground wire from the (GREEN)

ground screw next to the terminal block.

6. Attach the ground (GREEN) power cord

wire to the cabinet with the ground (GREEN)

screw. Tighten the screw securely.

7. Move the internal dryer harness ground

(WHITE) wire to the terminal block and

attach it along with the neutral (WHITE)

power cord wire conductor to the center,

SILVER colored terminal on the terminal

block. Tighten the screw securely.

8. Attach the RED and BLACK power cord

conductors to the outer, BRASS colored

terminals on the terminal block. Tighten both

screws securely.

Neutral

(WHITE wire)

30 AMP

NEMA 14-30

Ground

(GREEN wire)

9. Follow manufacturer’s guidelines for ﬁ rmly

securing the strain relief and power cord.

10. Reinstall the terminal block cover.

Move internal ground (WHITE)

wire to neutral (SILVER)

terminal for 4-wire system.

Neutral

terminal

GREEN

ground screw

BLACK or

RED power wire

BLACK

or RED

power wire

GREEN

ground wire

WHITE

neutral wire

NOTE

If a terminal screw falls during cord installation,

it can be retrieved in the terminal screw

recovery slot below the access panel.

WARNING

ELECTRICAL SHOCK HAZARD

Do not make a sharp bend or crimp wiring/

conductor at connections.

WARNING

ELECTRICAL SHOCK HAZARD

Failure to disconnect power source before

servicing could result in personal injury or even

death.

14 Installation Instructions

Gas connection

1. Remove the shipping cap from gas pipe at

the rear of the dryer.

2. Connect a 1/2 inch (1.27 cm) I.D. semi-rigid

or approved pipe from gas supply line to the

3/8 inch (0.96 cm) pipe located on the back

of the dryer. Use a 1/2 inch to 3/8 inch (1.27

cm to 0.96 cm) reducer for the connection.

Apply an approved thread sealer that is

resistant to the corrosive action of liqueﬁ ed

gases on all pipe connections.

3. Open the shutoﬀ valve in the gas supply line

to allow gas to ﬂ ow through the pipe. Wait

a few minutes for gas to move through the

gas line.

All connections must be wrench-tightened

Flare

Union

Flare

Union

GAS FLOW

Manual

Shuto

Valve

Closed

Open Flexible

Connector

Inlet Pipe on

Back of Dryer

elppiN

Shuto Valve -

Open position

to dryer

from gas supply

4. Check for gas system leaks with a

manometer. If a manometer is not available,

test all connections by brushing on a soapy

water solution.

WARNING

EXPLOSION HAZARD

NEVER test for gas leaks with an open ﬂ ame.

IMPORTANT

DO NOT connect the dryer to L.P. gas service

without converting the gas valve. An L.P. con-

version kit must be installed by a qualiﬁ ed gas

technician.

IMPORTANT

Installation to the gas service must follow local

codes and ordinances and the latest edition of

the National Fuel Gas Code ANSI Z223.1/NEPA

54 or in Canada, CSA B149.1.

15

Installation Instructions

Water connection (Steam Model only)

1. Turn oﬀ COLD water supply to washer,

2. Remove COLD inlet hose from COLD water

supply and inspect for rubber washer.

Replace washer if it is torn or worn out.

3. Momentarily turn on COLD supply and run

some water into a bucket or container to

clear any contaminants in the line.

4. Remove hose kit from dryer drum and

inspect hose couplings for proper

placement of rubber washers.

RUBBER WASHER

MUST BE PRESENT

AND UNDAMAGED

COLD INLET HOSE

TO WASHER

WATER SUPPLY REQUIREMENTS

Cold water faucet MUST be installed within 42

inches (107 cm) of your dryer’s water inlet. The

faucet MUST be 3/4 inch (1.9 cm) with thread-

ing for laundry hose connection. Water pressure

MUST be between 30 and 120 psi. Your water de-

partment can advise you of your water pressure.

RUBBER WASHERS

MUST BE PRESENT

16 Installation Instructions

WATER INLET

ON DRYER

DIRECT CONNECTION

OR WITH EXTENSION

COLD WATER SUPPLY

HOSE TO WASHER

5. If your installation has room for the COLD

water supply to accept the “Y” connector

directly, thread the “Y” connector to the

COLD water supply and snug it by hand;

then tighten it another 2/3 turn with pliers.

6. If there is not room to install the “Y”

connector directly, thread the short

extension hose on to the COLD water

supply and snug it by hand; then tighten it

another 2/3 turn with pliers.

7. Thread the “Y” connector to the short

extension hose and snug it by hand; then

tighten it another 2/3 turn with pliers.

8. Connect the COLD inlet hose for the washer

to the “Y” connector and snug it by hand;

then tighten it another 2/3 turn with pliers.

9. Connect the straight end of the long hose

from the kit to the other outlet on the “Y”

connector and snug it by hand. Connect

the hose’s 90° coupling to the brass water

inlet on the back of the dryer and snug it by

hand. Tighten each connection of the dryer

inlet hose another 2/3 turn with pliers.

10. Turn on the water and check for leaks at all

connections.

Water connection, continued (Steam Model only)

NOTE

If you were able to install the “Y” connector

directly to the COLD water supply, please skip

to step 8.

17

Installation Instructions

General installation

1. Connect the exhaust duct to the outside

exhaust system. Use of a 4” (102 mm) clamp

(item A) is recommended to connect the

dryer to the exhaust vent system. Use metal

foil tape to seal all other joints.

2. Use a carpenter’s level to level your dryer

front-to-back and side-to-side.

3. Use adjustable pliers to adjust the leveling

legs so the dryer is level front-to-rear and

side-to-side, and stable corner-to-corner.

4. Press down on alternate corners and sides

and feel for the slightest movement. Adjust

the appropriate leg(s) so the dryer sits

solidly on the ﬂ oor on ALL four legs. Keep

the leveling leg extension at a minimum for

best performance of the dryer.

5. Plug the power cord into a grounded outlet.

A

Grounding type

wa

ll receptacl

ll receptacle

Po

wer cord with

3-prong

gr

ounded plug

Do not,

under

an

y cir

cumstances,

cut,

remo

ve

ve,

or b

ypass th

ypass the

gr

ounding pr

ong.

6. Turn on the power at the circuit breaker/fuse

box.

7. Read the Use & Care Guide provided with

the dryer. It contains valuable and helpful

information that will save you time and

money.

8. If you have any questions during initial

operation, please review the “Avoid Service

Checklist” in your Use & Care Guide before

calling for service.

9. Place these instructions in a location near

the dryer for future reference.

IMPORTANT

Be sure the power is oﬀ at a circuit breaker/

fuse box before plugging the power cord into

an outlet.

NOTE

A wiring diagram and technical data sheet are

located under the dryer top panel.

CAUTION

When discarding or storing your old dryer,

remove the door.

18 Reversing Door

A) Removing Latch Cover and Hole Plugs

1. Open the door.

2. Remove plastic hole plugs and save to

reinstall later. You may have to use a nan-

scratching plastic knife if you are unable

to dislodge the plugs manually.

B) Removing Door Assembly

1. Completely open the door to expose all

four hinge screws.

2. Remove all four hinge screws with #2

square bit driver. Save for reinstalling later.

3. Remove both screws from door latch

cover. Save cover and screws for

reinstallation later.

WARNING

ELECTRICAL SHOCK HAZARD

Failure to disconnect power source before

servicing could result in personal injury or

even death.

IMPORTANT

BEFORE YOU REVERSE YOUR DRYER DOOR:

1. Be sure you have adequate swing area

before reversing door.

2. Gather your tools - including a screw

driver with a #2 square bit and plastic

knife (or small, ﬂ at prying tool that won’t

damage paint).

3. Be sure dryer is unplugged from power

source!

x 2

x 4

x 2

3. Grasp the door with both hands and lift

slightly as you pull door and hinge away

from the front panel.

Screwdriver

with #2

square bit

Tools needed for reversal:

Plastic

knife

19

Reversing Door

x 4

x 2

C) Reinstalling Door Assembly

1. Rotate the door and hang the hook upper

hook on the back of the hinge in the

upper hole of the front panel.

D) Reinstalling Latch Cover and Hole Plugs

1. Install door latch cover with screws

removed earlier.

E) Verify Reversed Door Operation

1. Test door for free, smooth swinging

operation and secure latching when

closed.

2. Plug in dryer and close the door. Start

a test cycle: drum should tumble until

door is pulled open or cycle is paused or

canceled.

2. Reinstall and tighten all four screws

removed earlier.

2. Insert plastic hole plugs removed earlier.

20 Options

Accessories

MATCHING STORAGE PEDESTAL*

White Pedestal - P/N EPWD157SIW

Titanium Pedestal - P/N EPWD157STT

A storage pedestal accessory, speciﬁ cally

designed for this dryer may be used to elevate

the dryer for ease of use. This pedestal will add

about 15” (38 cm) to the height of your unit.

*Other colors may be available. Contact the source

where you purchased your dryer.

DRYER STACKING KIT

P/N STACKIT7X

Depending on the model you purchased, a kit for

stacking a matching dryer on top of this washer

may have been included in the initial purchase

of your dryer. If your model did not include a

stacking kit or you desire another stacking kit, you

may order one.

LP CONVERSION KIT

P/N 134709300

Gas dryers intended for use in a location

supplied with LP must use a conversion kit prior

to installation.

MOBILE HOME INSTALLATION KIT

P/N 137067200

Installations in mobile homes require use of

MOBILE HOME INSTALLATION KIT.

DRYING RACK

P/N A04840701

Depending on the model you purchased, a

drying rack may have been included in the

initial purchase of your dryer. If your model did

not include a drying rack or you desire another

drying rack, you may order one.

UNIVERSAL APPLIANCE WRENCH

P/N 137019200

A UNIVERSAL APPLIANCE WRENCH is

available to aid in dryer/washer/pedestal feet

adjustment.

TOUCH UP PAINT PENS

White - P/N 5304468812

Titanium - P/N 5304475700

*Other colors may be available. Contact the source

where you purchased your dryer.

Replacement parts in U.S. and Canada:

If replacements parts are needed for your

dryer, you can contact the source where you

purchased your dryer, call 1-877-4ELECTROLUX

(1-877-435-3287) in the U.S. or 1-800-265-8352

in Canada, or visit our website, www.

electroluxappliances.com, for the Electrolux

Authorized Parts Distributor nearest you.

CAUTION

Failure to use accessories manufactured by (or

approved by) the manufacturer could result in

personal injury, property damage or damage

to the dryer.

WARNING

ELECTRICAL HAZARD

Label all wires prior to disconnection when

servicing controls. Wiring errors can cause

improper and dangerous operation. Verify

proper operation after servicing.

26.5”

(67 cm)

15”

(38 cm)

27”

(68.5 cm)

La page charge ...

Electrolux EFME617STT Guide d'installation

Electrolux EFME617STT Guide d'installation

dans d''autres langues