Samsung DW80N3030US/AA Guide d'installation

DW80N3030 Series

DD81-02614A-01

DW80N3030 Series

23 "(604mm)

33 "(858mm)

2 "(58.5mm)

6 "(154mm)

24"(610mm)

minimum

34 "(867mm)

minimum

24 inches deep and 34 inches high.

24"(610mm)

minimum

3

4

3

4

5

16

1

16

1

8

1

8

2 (6 mm)

24 "(625mm)

20 "(520.7mm)

1

2

5

8

4

3

4"

29

Kick Plate

For the hot water supply line – We strongly recommend using ⅜" minimum O.D. copper tubing with

a compression fitting or a flexible stainless steel braided hot water supply line.

Do not use plastic tubing. Plastic tubing can deteriorate over time and cause a leak inside the tube

fitting.

You also need a 90° Fitting with ¾" N.P.T. external pipe threads on one end and a fitting sized to fit

your hot water supply line (copper tubing/compression fitting or braided hose) on the other.

For the power cable, we recommend a jacketed 12-2 cable with ground. Note that some local codes

may require the cable to have a BX style metal jacket.

⅜"

Cable Tie

(for the Drain hose1)

Nut connector & seal

(for ¾" 90° ﬁ tting)

15

existing

The location must have sufficient space for the dishwasher door to open easily and provide

Using a 2 inch hole saw, cut a hole into the side of the cabinet that hold the sink as

1

2

s

Drain hose1

Drain hose2

Connect drain

through the hole on the side wall so it can be connected to the drain outlet at the sink.

When you install the dishwasher, ensure there is nothing in the drain hose, and be

careful not to damage the drain hose during installation.

hose

2 to drain hose 1 using the provided clamp. Then run drain hose 2

rear

STEP 6 PREPARING THE DISHWASHER

1.

Use the provided nut connector to connect the water hose to the dishwasher.

Follow these steps:

1 2 3

A

B

C

E

F

D

1) Disconnect the 90° ﬁ tting (A) from the hose (B).

2) Remove the seal (C) and the nut (D) from the 90° ﬁ tting.

3) From the provided nut connector, separate the seal (E) and the nut (F), and then

assemble them to the 90° ﬁ tting as shown in the ﬁ gure. You must insert the smaller side

of the seal.

Then, insert the ¾" 90 degree ﬁ tting into the inlet valve (see Figure 4-B). Tighten until the ¾"

ﬁ tting is tight. Do not over tighten.

2.

3.

5.

6.

Hot Water Supply LineHot Water Supply Line

Elbow( 3/4" (9.5 mm))Elbow( 3/4" (9.5 mm))

Inlet valveInlet valve

Drain Hose2

Drain Hose1

4

If the leveling legs are rotated to the right (counter

clockwise),they are lo sened and the front of the

dishwasher is raised. And the maximum height be

raised is about 38mm(1 ").If they are rotated to the

left (clockwise),they are tightened and the front of

the dishwasher is lowered.

1

2

legs.

o

Drain hose2

1

2

3

4

Drain hose2

Only qualified electricians should perform electrical

To avoid a fire hazard,make sure electrical work is

inserting

La page charge ...

Samsung DW80N3030US/AA Guide d'installation

Samsung DW80N3030US/AA Guide d'installation

dans d''autres langues

Documents connexes