Samsung DW80N3030US/AA Guide d'installation

Taper
Guide d'installation
DW80N3030 Series
DD81-02614A-01
DW80N3030 Series
23 "(604mm)
33 "(858mm)
2 "(58.5mm)
6 "(154mm)
24"(610mm)
minimum
34 "(867mm)
minimum
24 inches deep and 34 inches high.
24"(610mm)
minimum
3
4
3
4
5
16
1
16
1
8
1
8
2 (6 mm)
24 "(625mm)
20 "(520.7mm)
1
2
5
8
4
3
4"
29
Kick Plate
For the hot water supply line – We strongly recommend using ⅜" minimum O.D. copper tubing with
a compression fitting or a flexible stainless steel braided hot water supply line.
Do not use plastic tubing. Plastic tubing can deteriorate over time and cause a leak inside the tube
fitting.
You also need a 90° Fitting with ¾" N.P.T. external pipe threads on one end and a fitting sized to fit
your hot water supply line (copper tubing/compression fitting or braided hose) on the other.
For the power cable, we recommend a jacketed 12-2 cable with ground. Note that some local codes
may require the cable to have a BX style metal jacket.
⅜"
Cable Tie
(for the Drain hose1)
Nut connector & seal
(for ¾" 90° fi tting)
15
existing
The location must have sufficient space for the dishwasher door to open easily and provide
Using a 2 inch hole saw, cut a hole into the side of the cabinet that hold the sink as
1
2
s
Drain hose1
Drain hose2
Connect drain
through the hole on the side wall so it can be connected to the drain outlet at the sink.
When you install the dishwasher, ensure there is nothing in the drain hose, and be
careful not to damage the drain hose during installation.
hose
2 to drain hose 1 using the provided clamp. Then run drain hose 2
rear
STEP 6 PREPARING THE DISHWASHER
1.
Use the provided nut connector to connect the water hose to the dishwasher.
Follow these steps:
1 2 3
A
B
C
E
F
D
1) Disconnect the 90° fi tting (A) from the hose (B).
2) Remove the seal (C) and the nut (D) from the 90° fi tting.
3) From the provided nut connector, separate the seal (E) and the nut (F), and then
assemble them to the 90° fi tting as shown in the fi gure. You must insert the smaller side
of the seal.
Then, insert the ¾" 90 degree fi tting into the inlet valve (see Figure 4-B). Tighten until the ¾"
tting is tight. Do not over tighten.
2.
3.
5.
6.
Hot Water Supply LineHot Water Supply Line
Elbow( 3/4" (9.5 mm))Elbow( 3/4" (9.5 mm))
Inlet valveInlet valve
Drain Hose2
Drain Hose1
4
If the leveling legs are rotated to the right (counter
clockwise),they are lo sened and the front of the
dishwasher is raised. And the maximum height be
raised is about 38mm(1 ").If they are rotated to the
left (clockwise),they are tightened and the front of
the dishwasher is lowered.
1
2
legs.
o
Drain hose2
1
2
3
4
Drain hose2
Drain hose2
Only qualified electricians should perform electrical
To avoid a fire hazard,make sure electrical work is
inserting
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

Samsung DW80N3030US/AA Guide d'installation

Taper
Guide d'installation

dans d''autres langues