Jenn-Air JB36NXFXLE Guide d'installation

JENN-AIR

®

BOTTOM MOUNT

BUILT-IN REFRIGERATOR

REFRIGERADOR EMPOTRADO CON

CONGELADOR EN LA PARTE INFERIOR

DE JENN-AIR

®

RÉFRIGÉRATEUR ENCASTRÉ AVEC

CONGÉLATEUR EN BAS JENN-AIR

®

W10735232A

INSTALLATION GUIDE

For questions about features, operation/performance, parts, accessories, or service,

call 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call 1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.ca.

GUÍA DE INSTALACIÓN

Si tiene preguntas respecto a las características, funcionamiento, rendimiento, partes, accesorios o servicio técnico,

llame al 1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio de internet: www.jennair.com.

En Canadá, llame al 1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio de internet: www.jennair.ca.

GUIDE D’INSTALLATION

Au Canada, pour assistance, installation ou service, composez le 1-800-JENNAIR (1-800-536-6247)

ou visitez notre site Web à www.jennair.ca.

Table of Contents / Índice / Table des matières ...................................................................................2

2

TABLE OF CONTENTS

REFRIGERATOR SAFETY........................................................................... 3

36" SINGLE-DOOR MODELS..................................................................... 4

Accessories...............................................................................................4

36" FRENCH DOOR MODELS.................................................................... 5

Accessories...............................................................................................5

42" FRENCH DOOR MODELS.................................................................... 6

Accessories...............................................................................................6

INSTALLATION REQUIREMENTS ............................................................. 7

Tools and Parts......................................................................................... 7

Location Requirements............................................................................. 8

Electrical Requirements............................................................................9

Water Supply Requirements...................................................................10

Product Dimensions ...............................................................................10

Tipping Radius........................................................................................11

Door Swing Dimensions .........................................................................12

Cabinet and Panel Installation Options..................................................12

Fully Integrated Grille Installation Requirements....................................13

Standard Integrated Grille Installation Requirements............................ 14

Stainless Steel Panel Kit Installation Requirements............................... 15

Custom Wood Overlay Panel Requirements ......................................... 15

Custom Wood Overlay Panel Dimensions............................................. 16

INSTALLATION INSTRUCTIONS............................................................. 17

Unpack the Refrigerator ......................................................................... 17

Move the Refrigerator into House .......................................................... 18

Install Anti-Tip Boards ............................................................................ 18

Connect the Water Supply ..................................................................... 18

Plug in Refrigerator................................................................................. 20

Install Side Trims .................................................................................... 20

Move Refrigerator to Final Location....................................................... 21

Level and Align Refrigerator ................................................................... 21

Install Refrigerator and Panels ............................................................... 22

Install Base Grille .................................................................................... 27

Complete Installation.............................................................................. 27

ÍNDICE

SEGURIDAD DEL REFRIGERADOR........................................................29

MODELOS DE UNA PUERTA, DE 36"..................................................... 30

Accesorios ..............................................................................................30

MODELOS DE DOS PUERTAS CON CONGELADOR

EN LA PARTE INFERIOR, DE 36" ............................................................31

Accesorios ..............................................................................................31

MODELOS DE DOS PUERTAS CON CONGELADOR

EN LA PARTE INFERIOR, DE 42" ............................................................32

Accesorios ..............................................................................................32

REQUISITOS DE INSTALACIÓN..............................................................33

Herramientas y piezas ............................................................................33

Requisitos de ubicación .........................................................................34

Requisitos eléctricos...............................................................................36

Requisitos del suministro de agua .........................................................36

Dimensiones del producto......................................................................37

Arco de vuelco........................................................................................ 38

Medidas de oscilación de las puertas....................................................38

Opciones para la instalación del armario y los paneles.........................39

Requisitos para la instalación de

la rejilla completamente incorporada ..................................................... 40

Requisitos para la instalación de la rejilla incorporada estándar .......... 41

Requisitos de instalación del juego de paneles de acero inoxidable.... 41

Requisitos para los paneles de madera recubiertos a la medida ......... 42

Dimensiones de los paneles de madera recubiertos a la medida......... 43

INSTRUCCIONES DE INSTALACIÓN...................................................... 44

Desempaque el refrigerador................................................................... 44

Cómo introducir el refrigerador en la casa............................................. 45

Cómo instalar los tableros antivuelco .................................................... 45

Conexión del suministro de agua........................................................... 46

Cómo enchufar el refrigerador ............................................................... 47

Instalación de las molduras laterales ..................................................... 48

Cómo mover el refrigerador a su ubicación final................................... 48

Nivelación y alineamiento del refrigerador............................................. 49

Instalación del refrigerador y los paneles............................................... 49

Instalación de la rejilla de la base........................................................... 56

Complete la instalación .......................................................................... 56

TABLE DES MATIÈRES

SÉCURITÉ DU RÉFRIGÉRATEUR ........................................................... 57

MODÈLES AVEC PORTE À BATTANT SIMPLE DE 36".........................58

Accessoires.............................................................................................58

MODÈLES AVEC PORTE À DOUBLE BATTANT DE 36".......................59

Accessoires.............................................................................................59

MODÈLES AVEC PORTE À DOUBLE BATTANT DE 42".......................60

Accessoires.............................................................................................60

EXIGENCES D’INSTALLATION................................................................61

Outillage et pièces ..................................................................................61

Exigences d’emplacement .....................................................................62

Spécifications électriques.......................................................................64

Spécifications de l’alimentation en eau..................................................64

Dimensions du produit............................................................................ 65

Rayon de basculement...........................................................................66

Dimensions pour l’ouverture des portes ................................................66

Options d’installation du placard et du panneau ...................................67

Exigences d’installation d’une grille totalement intégrée.......................68

Exigences d’installation d’une grille intégrée standard ......................... 69

Spécifications pour l’installation de l’ensemble

de panneaux en acier inoxydable .......................................................... 69

Spécifications des panneaux en bois décoratifs personnalisés............ 70

Panneaux décoratifs en bois personnalisés - Dimensions.................... 70

INSTRUCTIONS D’INSTALLATION ......................................................... 72

Déballage du réfrigérateur...................................................................... 72

Déplacement du réfrigérateur dans le domicile ..................................... 72

Installation de planches antibasculement.............................................. 73

Raccordement à l’alimentation en eau................................................... 73

Branchement du réfrigérateur ................................................................ 75

Installation des garnitures latérales........................................................ 75

Déplacement du réfrigérateur à son emplacement définitif................... 76

Réglage de l’aplomb et alignement du réfrigérateur.............................. 76

Installation du réfrigérateur et des panneaux......................................... 77

Installation de la grille de la base ........................................................... 83

Achever l’installation............................................................................... 83

3

REFRIGERATOR SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

4

36" SINGLE-DOOR MODELS

Custom-Made Panel Design

Features custom-made panels and custom hardware provided

by the cabinetmaker for a seamless appearance designed to

blend with existing kitchen cabinetry.

Base Model Numbers: JB36NXFXLE, JB36NXFXRE

Pro-Style

®

Stainless Design

Features stainless steel wrapped doors and Pro-Style

®

handles with

diamond-etched grip.

Base Model Numbers: JB36NXFXLE, JB36NXFXRE

Kit Model Number: JPK36BNXEPS

Accessories

All factory parts are available through your Jenn-Air dealer or by

calling Jenn-Air at 1-800-JENNAIR (1-800-536-6247). In Canada,

call 1-800-807-6777.

Door Handle Kits

For custom wood overlay panels only, handle kits can be ordered.

Follow the kit instructions for installation.

IMPORTANT: These handle kits are not intended for use with

stainless steel door panel kits.

Pro-Style

®

Stainless Steel—BM—W10250641

Euro-Style Stainless Steel—BM—W10250638

Armoire-Style Door Panel Kit

Refer to the installation instructions that come with the Armoire kit,

for custom wood overlay panel dimensions and installation details.

36" Model (Black)—W10663562

Euro-Style Stainless Design

Features stainless steel wrapped doors and new Euro-style

handles designed to compliment the Jenn-Air

®

Euro kitchen

suite or enhance any kitchen decor.

Base Model Numbers: JB36NXFXLE, JB36NXFXRE

Kit Model Number: JPK36BNXESS

5

36" FRENCH DOOR MODELS

Custom-Made Panel Design

Features custom-made panels and custom hardware provided

by the cabinetmaker for a seamless appearance designed to

blend with existing kitchen cabinetry.

Base Model Number: JF36NXFXDE

Pro-Style

®

Stainless Design

Features stainless steel wrapped doors and Pro-Style

®

handles with

diamond-etched grip.

Base Model Number: JF36NXFXDE

Kit Model Number: JPK36FNXEPS

Accessories

All factory parts are available through your Jenn-Air dealer or by

calling Jenn-Air at 1-800-JENNAIR (1-800-536-6247). In Canada,

call 1-800-807-6777.

Door Handle Kits

For custom wood overlay panels only, handle kits can be ordered.

Follow the kit instructions for installation.

IMPORTANT: These handle kits are not intended for use with

stainless steel door panel kits.

Pro-Style

®

Stainless Steel FDBM—W10745429

Euro-Style Stainless Steel FDBM—W10745430

Armoire-Style Door Panel Kit

Follow the kit instructions for installation.

36" Model (Black)—W10663562

Euro-Style Stainless Design

Features stainless steel wrapped doors and new Euro-style

handles designed to compliment the Jenn-Air

®

Euro kitchen

suite or enhance any kitchen decor.

Base Model Number: JF36NXFXDE

Kit Model Number: JPK36FNXESS

6

42" FRENCH DOOR MODELS

Custom-Made Panel Design

Features custom-made panels and custom hardware provided

by the cabinetmaker for a seamless appearance designed to

blend with existing kitchen cabinetry.

Base Model Number: JF42NXFXDE

Pro-Style

®

Stainless Design

Features stainless steel wrapped doors and Pro-Style

®

handles with

diamond-etched grip.

Base Model Number: JF42NXFXDE

Kit Model Number: JPK42FNXEPS

Accessories

All factory parts are available through your Jenn-Air dealer or by

calling Jenn-Air at 1-800-JENNAIR (1-800-536-6247). In Canada,

call 1-800-807-6777.

Door Handle Kits

For custom wood overlay panels only, handle kits can be ordered.

Follow the kit instructions for installation.

IMPORTANT: These handle kits are not intended for use with

stainless steel door panel kits.

Pro-Style

®

Stainless Steel FDBM—W10250642

Euro-Style Stainless Steel FDBM—W10250639

Armoire-Style Door Panel Kit

Follow the kit instructions for installation.

42" Model (Black)—W10663564

Euro-Style Stainless Design

Features stainless steel wrapped doors and new Euro-style

handles designed to compliment the Jenn-Air

®

Euro kitchen

suite or enhance any kitchen decor.

Base Model Number: JF42NXFXDE

Kit Model Number: JPK42FNXESS

7

INSTALLATION REQUIREMENTS

Tools and Parts

IMPORTANT:

■ Installer: Leave Installation Instructions with the homeowner.

■ Homeowner: Keep Installation Instructions for future

reference. Save these Installation Instructions for the local

electrical inspector’s use.

Tools Needed:

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Parts Needed:

■ #8 x 3" (7.6 cm) wood screws (longer screws may be needed) (6)

■ 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood boards (2)

■ Custom wood overlay panels—consult a qualified

cabinetmaker or carpenter to make the custom wood panels.

See “Custom Wood Overlay Panels” for more information.

OR

Panel kit—See “36" Models or 42" French Door Models” for

panel kit information.

■ Flexible, codes-approved water supply tubing, a ferrule, a

union and a ¹⁄₄" (6.35 mm) compression fitting.

Parts Provided:

■ Cordless drill

■ Drill bits

■ Adjustable wrenches (2)

■ Phillips screwdriver

■ Small level

■ ³⁄₃₂" hex key

(panel kits only)

■ ¹¹⁄₃₂" nut driver

■ ³⁄₈" and ¹⁄₂" open-end wrenches

■ ⁵⁄₃₂" and ³⁄₁₆" hex key

■ ¹⁄₄" and ⁵⁄₁₆" socket drivers

■ Tape measure

■ Utility knife

■ Tape (painters)

■ Appliance dolly

Slotted Hex-head Screw

W10141645 (21)

Hex-head Pointed Screw

W10141189 (8)

Hex-head Blunt Screw

W10142233 (4)

Shoulder Washer (use with hex-head

pointed screw)

W10471946 (4)

Phillips-head Flat Screw

8281252 (28)

Round-head Screw

1163283 (24)

Door Adjustment Pin

(preinstalled)

W10234194 (2)

Door Stop Pin

W10234202 (2)

Drawer Panel Bracket

W10606815 (2)

Standard Integrated Grille Bracket

W10182743—Left (1)

W10182741—Right (1)

Fully Integrated Grille

Bracket

W10260890—Left (1)

W10260891—Right (1)

Filler Board “L” Bracket

W10234199 (2)

Panel Top Bracket

W10667450 (2)

Top Grille Lower Trim

W10634858—36" BM (1)

W10606812—42" BM, SxS (1)

8

Location Requirements

IMPORTANT:

■ Observe all governing codes and ordinances.

■ It is recommended that you do not install the refrigerator near

an oven, radiator, or other heat source.

■ Do not install in a location where the temperature will fall

below 55°F (13°C).

■ Floor must support the refrigerator weight, more than 600 lbs

(272 kg), door panels and contents of the refrigerator. Flooring

under refrigerator must be at same level as the room. Face of

cabinetry must be plumb.

■ Ceiling height must allow for side tipping radius. See “Tipping

Radius.”

■ Location should permit door to open fully. See “Door Swing

Dimensions.”

■ Location must permit top grille removal. See “Opening

Dimensions.”

Opening Dimensions

IMPORTANT:

■ The width of the opening (Width A), from side to side, must be

as specified for your model, for at least 2" (5.08 cm) back from

the face of the cabinet.

NOTE: If your opening does not meet this requirement, you

will need to make modifications.

■ A solid soffit or wall cabinet must be installed 84" (213.4 cm)

above the floor. If the solid soffit is higher than 84" (213.4 cm)

or one is not available, then the refrigerator must be braced.

If anti-tip boards are needed, they must be attached to the

rear wall studs so that there is 84" (213.4 cm) from the bottom

of the anti-tip board to the floor. See “Install Anti-Tip Boards”

for more information.

NOTES:

■ A clearance of ¹⁄₂" (1.3 cm) must be maintained above the

top grille so that the top grille can be removed.

■ Do not remove the foam gasket from the top of the

compressor cover unless removal is necessary to fit the

unit under a soffit. Removal of the gasket will cause loss in

cooling efficiency.

■ If installing under a solid soffit, after installation raise the

leveling legs so that the gasket is pressed snugly against

the soffit.

■ For a fully integrated installation, a minimum of 6" (15.24 cm)

of open space above the refrigerator is required. See “Fully

Integrated Installation.” Anti-tip boards are required. See

“Install Anti-Tip Boards” for more information.

■ A grounded 3 prong electrical outlet should be located within

a specified number of inches from the right-hand side

cabinets or end panel. See the chart following the graphic for

the number of inches required for your model. For more

information, see “Electrical Requirements.”

RC Hinge Cover Trim

W10648975—36" BM

(Right)

W10564251—36" FDBM

(Right)

W10606804—42" FDBM

(Right)

FC Hinge Cover Trim

W10611107—36" BM (Left)

W10582015—36" FDBM (Left)

W10606808—42" FDBM (Left)

Panel Templates

W10222281—SxS

W10488115—36" BM

W10704869—36" FDBM

W10488118—42" FDBM

W10489178—Grille

Handle Side Door Trim

W10611106—BM (Left)

W10648977—BM (Right)

W10606802—FDBM (Right)

W10606806—FDBM (Left)

Installation Block

W10234156

Grille—Bottom / Skirt—Grille

W10189198 / W10188549—42" BM

W10189196 / W10188547—36" BM

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

A. Gasket

B. Compressor cover

¹⁄₂"

(1.3 cm)

B

A

9

■ The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible

area. If the water shutoff valve is not in the cabinets, the

plumbing for the water line can come through the floor. See

“Water Supply Requirements” for more information.

Electrical Requirements

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 volt, 60 Hz., AC only, 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground Fault

Circuit Interrupter) protected outlet, nuisance tripping of the

power supply may occur, resulting in loss of cooling. Food quality

and flavor may be affected. If nuisance tripping has occurred, and

if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation or cleaning,

remove the top grille and turn the master power switch to OFF or

disconnect power at the circuit breaker box.

When you are finished, turn ON the master power switch or

reconnect power at the circuit breaker box. Then reset the control

to the desired setting.

Model

Width A

(as shown above)

Dimension B

(as shown above)

36

42

36" (91.4 cm)

42" (106.7 cm)

4" (10.2 cm)

7¹⁄₂" (19.1 cm)

Installation Type Depth C (as shown

above)

Standard Flush

(new installation)

25" (63.5 cm) minimum

Retrofit Installations 24" (60.9 cm) minimum

84" (213.4 cm)

to bottom of solid soffit

77"

(196 cm)

A

Width

(see chart following)

C Depth

B

Dimension

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

10

Water Supply Requirements

IMPORTANT:

■ All installations must meet local plumbing code requirements.

■ There is not enough clearance to achieve a flush installation if

a water shutoff valve is located in the wall behind the

refrigerator.

■ The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible

area. The water supply line, however, must come up through

the floor in the gray shaded area shown.

■ A ½" (12.7 mm) hole for plumbing should be drilled on the

floor at least 6" (15.2 cm) from the right- or left-hand side

cabinet and should be no more than 1" (2.54 cm) away from

the back wall. See “Connect the Water Supply.”

■ The water supply connection is made at the front of the

refrigerator.

■ If additional tubing is needed, use copper tubing and check

for leaks. Install the copper tubing only in areas where the

household temperatures will remain above freezing.

■ Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve

which reduces water flow and also clogs more easily.

NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper

tubing. Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes.

Water Pressure

A cold water supply with water pressure between 30 and 120 psi

(207 and 827 kPa) is required to operate the water dispenser and

ice maker. If you have questions about your water pressure, call a

licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 and

827 kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

■ If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter cartridge.

If you have questions about your water pressure, call a licensed,

qualified plumber.

Product Dimensions

IMPORTANT:

■ The depth from the front face of the doors to the back of the

refrigerator cabinet is 24" (60.96 cm) without panels.

■ The power cord is 84" (213 cm) long.

■ The water supply connection is made at the bottom front of

the refrigerator.

36" Single Door and 36" French Door Bottom Mount

Top View

Front View

■ Width dimensions were measured from hinge edge to clip

edge.

■ When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below

rollers, add 1¹⁄₄" (3.2 cm) to the height dimension.

1"

(2.54 cm)

6"

(15.2 cm)

6"

(15.2 cm)

6"

(15.2 cm)

35³⁄₄"

(90.8 cm)

24"

(61.0 cm)

83¹⁄₈"

(211.1 cm)

35³⁄₄"

(90.8 cm)

11

42" French Door Bottom Mount

Top View

Front View

■ Width dimensions were measured from hinge edge to hinge

edge.

■ When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below

rollers, add 1¹⁄₄" (3.2 cm) to the height dimension.

Tipping Radius

Be sure there is adequate ceiling height to stand the refrigerator

upright when it is moved into place.

■ The dolly wheel height must be added to the tipping radius

when a dolly is used.

NOTE: Tip on side only.

Side Tipping Radius—36" (91.4 cm) Models

Side Tipping Radius—42" (106.7 cm) Models

41³⁄₄"

(106.1 cm)

24"

(61.0 cm)

83¹⁄₈"

(211.1 cm)

41³⁄₄"

(106.1 cm)

A. 88

⁷⁄₈

" (225.7 cm)

A. 91

³⁄₈

" (232.1 cm)

A

12

Door Swing Dimensions

■ The location must permit both doors to open to a minimum of

90°.

■ Allow 4¹⁄₂" (11.4 cm) minimum space between the side of the

refrigerator and a corner wall.

NOTE: More clearance may be required if you are using custom

wood overlay panels, custom handles or extended handles.

36" (91.4 cm) Single Door Models

36" (91.4 cm) and 42" (106.6 cm) French Door Models

Cabinet and Panel

Installation Options

NOTE: Graphics shown below illustrate installation configuration

options given the specified cabinet depths. All possible

configurations are not shown.

Cabinet Depth—25" (63.5 cm)

Framed Cabinetry

Top View

Inset

Top View

Frameless Cabinetry

Top View

Model A B C D

36 58³⁄₄"

(149.2 cm)

56⁵⁄₈"

(143.8 cm)

56⁵⁄₈"

(143.8 cm)

58³⁄₄"

(149.2 cm)

36 FD 41"

(104 cm)

39³⁄₄"

(101 cm)

39³⁄₄"

(101 cm)

41"

(104 cm)

42 FD 44"

(111.8 cm)

42³⁄₄"

(108.6 cm)

42³⁄₄"

(108.6 cm)

44"

(111.8 cm)

90º

B

A

110º

110˚

90˚

110˚

90˚

BA C D

A. Refrigerator door

B. Door panel

C. Side trim

D. Adjacent cabinet

E. Flush return filler

F. 25" (63.5 cm)

A. Refrigerator door

B. Door panel

C. Side trim

D. Adjacent cabinet

E. Flush return filler

F. 25" (63.5 cm)

A. Refrigerator door

B. Door panel

C. Side trim

D. Adjacent cabinet

E. 25" (63.5 cm)

F

B

E

D

C

A

E

D

C

F

A B

D

C

A B

E

13

Cabinet Depth—24" (60.9 cm)

NOTE: A flush installation is not possible with a 24" (60.9 cm)

deep opening.

Framed Cabinetry

Top View

Frameless Cabinetry

Top View

Fully Integrated Grille Installation

Requirements

The refrigerator can be installed fully integrated if the adjacent

cabinetry meets the airflow venting requirements critical to

refrigerator performance. A Fully Integrated Grille installation has

no visible air gap because the grille extends upward to the soffit or

upper cabinet.

IMPORTANT:

■ A Fully Integrated Grille installation requires a minimum of 6"

(15.24 cm) of open space above the refrigerator. This space

must not be blocked in any way, including by soffits.

■ A Fully Integrated Grille installation can be achieved with

either a 24" (60.9 cm) or 25" (63.5 cm) deep opening.

■ A full height grille is used to achieve a Fully Integrated Grille

installation. Use the integrated grille bracket (provided with

refrigerator) to attach the full height grille.

NOTE: A top grille vent is not required with a full height grille.

Integrated Grille Bracket

Fully Integrated Grille Installation—Side View

A. Refrigerator door

B. Door panel

C. Side trim

D. Adjacent cabinet

E. Flush return filler

F. 24" (60.9 cm)

A. Refrigerator door

B. Door panel

C. Side trim

D. Adjacent cabinet

E. 24" (60.9 cm)

E

D

C

F

A B

D

C

A B

E

A. False front (optional)

B. Airflow

C. Full height grille*

D. Door panel*

*C and D are one piece in the Full-height Door

Installation option.

A

B

C

D

14

Fully Integrated Grille Installation Options

Option 1—Open to Ceiling

Option 2—False Front (cabinet face only)

Standard Integrated Grille

Installation Requirements

IMPORTANT:

■ A Standard Integrated Grille installation can be achieved with

either a 24" (60.9 cm) or 25" (63.5 cm) deep opening.

■ A standard grille is used to achieve a Standard Integrated

Grille installation. Use the standard grille bracket (provided

with refrigerator) to attach the standard grille.

■ The grille panel height, shown in the “Standard Integrated

Grille Installation—Side View” graphic, allows for an air gap

critical to refrigerator performance.

Standard Grille Bracket

Standard Integrated Grille Installation—Side View

6" (15.24 cm)

min.

84"

(213.4 cm)

6" (15.24 cm)

min.

84"

(213.4 cm)

A. Top grille filler

B. Soffit

C. Airflow

D. Grille panel

E. Door panel

B

C

D

E

A

15

Standard Integrated Grille Installation—Full Product View

Stainless Steel Panel Kit

Installation Requirements

See the “36" Single Door Models” or the “36" or 42" French Door

Models” section to see the panel kit options available for your

model.

IMPORTANT:

■ A panel kit installation can be achieved with either a 24"

(60.9 cm) or 25" (63.5 cm) deep opening.

■ Refer to the instructions provided with the Stainless Steel

Door Panel Kit to install the door panels and standard grille.

■ The grille panel height, shown in the “Panel Kit Installation—

Side View” graphic, allows for an air gap critical to refrigerator

performance.

Panel Kit Installation—Side View

Panel Kit Installation—Full Product View

Custom Wood Overlay Panel

Requirements

Custom wood overlay panels allow you to blend the exterior of

your refrigerator into the overall kitchen décor and to use custom

handles for additional design flexibility.

In some cases, your cabinet manufacturer may choose to work

with one panel routed for the different dimensions. Follow these

panel dimension and placement instructions to be sure that the

custom wood overlay panels will fit properly.

IMPORTANT:

■ For 36" (91.4 cm) Single Door models, the refrigerator door

wood overlay panel cannot exceed 60 lbs (27.2 kg) and the

freezer drawer overlay panel cannot exceed 25 lbs (11.3 kg).

■ For 36" French Door models, the refrigerator door wood

overlay panel cannot exceed 38 lbs (17.2 kg) and the freezer

drawer overly panel cannot exceed 25 lbs (11.3 kg).

■ For 42" (106.7 cm) French Door models, the refrigerator door

wood overlay panel cannot exceed 38 lbs (17.2 kg) and the

freezer drawer overlay panel cannot exceed 30 lbs (13.6 kg).

■ The weight of the top grille wood overlay panel cannot exceed

7 lbs (3.2 kg) for both models.

■ The required thickness for all panels is ³⁄₄" (1.91 cm).

■ This installation does not require filler or backer panels.

C. Airflow

A. Soffit

B. Airflow

C. Grille panel

D. Door panel

C

A

B

C

D

16

Custom Wood Overlay Panel Dimensions

36" (91.4 cm) Single Door Model—Door and Drawer

Panels

*For Fully-integrated grille or Standard grille installations.

36" (91.4 cm) and 42" (106.7 cm) French Door

Models—Door and Drawer Panels

*For Fully-integrated grille or Standard grille installations.

Model 36" Single Door Bottom Mount

Reveal ³⁄₈" ¹⁄₈"

A 35¹⁄₄" (89.54 cm) 35³⁄₄" (90.81 cm)

B 35¹⁄₄" (89.54 cm) 35³⁄₄" (90.81 cm)

A

B

* 52³⁄₈"

(133.03 cm)

20¹⁄₂"

(52.07 cm)

FREEZER DRAWER PANEL

Maximum Weight: 25 lbs (11.34 kg)

REFRIGERATOR DOOR PANEL

Maximum Weight: 60 lbs (27.2 kg)

Pinch Hazard

Installation of door panels with less than a ³⁄₈" (0.95 cm) gap

between the door panel and the adjacent cabinet increases

the risk of potential pinching.

CAUTION

Model 36" French Door Bottom Mount

Reveal ³⁄₈" ¹⁄₈"

A 17⁹⁄₁₆" (44.6 cm) 17¹³⁄₁₆" (45.2 cm)

B 35¹⁄₄" (89.5 cm) 35³⁄₄" (90.8 cm)

Model 42" French Door Bottom Mount

Reveal ³⁄₈" ¹⁄₈"

A 20⁹⁄₁₆" (52.23 cm) 20¹³⁄₁₆" (52.86 cm)

B 41¹⁄₄" (104.78 cm) 41³⁄₄" (106.05 cm)

A

B

* 52³⁄₈"

(133.03 cm)

20¹⁄₂"

(52.07 cm)

FREEZER DRAWER PANEL

Maximum Weight: 30 lbs (13.6 kg)

REFRIGERATOR

DOOR PANEL

Maximum Weight:

38 lbs (17.2 kg)

A

REFRIGERATOR

DOOR PANEL

Maximum Weight:

38 lbs (17.2 kg)

Pinch Hazard

Installation of door panels with less than a ³⁄₈" (0.95 cm) gap

between the door panel and the adjacent cabinet increases

the risk of potential pinching.

CAUTION

17

Grille Panel

Fully-Integrated Installation—Full Height Grille—Open

Soffit

Standard Integrated Grille Installation—Open or

Closed Soffit

IMPORTANT: The grille panel height, shown in the “Standard

Integrated Grille Installation” graphic, allows for an air gap critical

to refrigerator performance.

Full-Height Door Installation - No Grille - Open Soffit

No grille is used in a full-height door installation. Use an Armoire

kit to disguise the cooling system, located on the top of the

refrigerator, which is visible when the doors are opened. See the

instructions, provided with the Armoire kit, for installation details

and custom wood overlay door dimensions.

INSTALLATION

INSTRUCTIONS

Unpack the Refrigerator

IMPORTANT:

■ Do not remove the film covering until the refrigerator is in its

operating location.

■ All four leveling legs must contact the floor to support and

stabilize the full weight of the refrigerator.

■ Keep the cardboard shipping piece or plywood under the

refrigerator until it is installed in the operating location.

1. Remove and save the literature package and hardware kit

located inside the refrigerator. Remove and save the literature,

grille, and trim taped to the outside of the refrigerator.

NOTE: Do not remove tape and door bracing until the

refrigerator is in its final location.

Model 36 42

Reveal ³⁄₈" ¹⁄₈" ³⁄₈" ¹⁄₈"

C 35¹⁄₄"

(89.54 cm)

35³⁄₄"

(90.81 cm)

41¹⁄₄"

(104.78 cm)

41³⁄₄"

(106.05 cm)

Model 36 42

Reveal ³⁄₈" ¹⁄₈" ³⁄₈" ¹⁄₈"

D 35¹⁄₄"

(89.54 cm)

35³⁄₄"

(90.81 cm)

41¹⁄₄"

(104.78 cm)

41³⁄₄"

(106.05 cm)

E 35¹⁄₄"

(89.54 cm)

35³⁄₄"

(90.81 cm)

41¹⁄₄"

(104.78 cm)

41³⁄₄"

(106.05 cm)

C

6

⁵⁄₈"

(16.83 cm)

Top Grille Panel

E

5

³⁄₄"

(14.55 cm)

Top Grille Panel

D

1" (2.54 cm)

Top Grille Filler

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

18

Move the Refrigerator into House

1. Place an appliance dolly under the left side of the refrigerator

as shown. Place the corner posts from the packing materials

over the trims as appropriate. Slowly tighten the strap.

2. Place pieces of the shipping carton on the floor when rolling

the dolly and refrigerator into the house. Move the refrigerator

close to the built-in opening.

3. Place top of cardboard carton or plywood under refrigerator.

4. Stand the refrigerator up. First, place the left bottom edge of

the refrigerator on the floor, stand the refrigerator upright and

then lower the right-hand side of the refrigerator to the floor.

Install Anti-Tip Boards

IMPORTANT:

■ If a solid soffit is not available, anti-tip boards must be

installed.

■ It is recommended that boards be installed before the

refrigerator is installed.

■ Boards must be long enough to fully cover the width of the

compressor cover.

■ Place the boards so that the bottom surfaces of the boards

are 84" (213 cm) from the floor.

■ During installation, raise the refrigerator up until the top of the

refrigerator is making contact with the bottom of the anti-tip

boards. Do not crush the compressor cover when raising the

rear leveling legs.

NOTE: The foam gasket, on top of the compressor cover, will

compress to fit under the anti-tip board(s). There is no need to

trim the gasket.

To Install Anti-tip Boards

1. Mark the stud locations on rear wall.

2. Securely attach two 2" x 4" x 32" (5 cm x 10 cm x 81 cm)

boards to wall studs behind refrigerator. Use six #8 x 3"

(7.6 cm) (or longer) wood screws. The wood screws must be

screwed into the studs at least 1½" (3.8 cm). The boards must

overlap the compressor cover.

Connect the Water Supply

Read all directions before you begin.

IMPORTANT: If you turn the refrigerator on before the water line is

connected, turn the ice maker OFF.

Connect to Water Line

Parts Needed

■ Minimum 7 ft (2.13 m) flexible, codes-approved water

supply line

Style 1—Shutoff Valve Connection

NOTE: If your water line connection does not look like Style 1, see

“Style 2—Copper Line Connection.”

1. Unplug refrigerator or disconnect power supply.

IMPORTANT:

■ There is not enough clearance to achieve a flush installation if

a water shutoff valve is located in the wall behind the

refrigerator. The water shutoff should be located in the base

cabinet on either side of the refrigerator.

■ Before attaching the tubing to shutoff valve, flush the main

water supply line to remove particles and air in the water line.

Allow enough flow so that water becomes clear. Flushing the

water line may help avoid filters and/or water valves from

becoming clogged.

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not

completely installed.

Keep doors taped closed until refrigerator is

completely installed.

Use two or more people to move and install

refrigerator.

Failure to do so can result in death or serious injury.

A. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards

B. Attach to studs with six #8 x 3" (7.6 cm) screws.

C. Compressor cover

D. Distance from bottom of anti-tip boards to floor

A

B

2" (5 cm)

C

84"

(213.4 cm)

D

19

2. Connect the flexible, codes-approved water supply line to the

water shutoff valve by threading the provided nut onto the

shutoff valve as shown.

3. Place the end of the tubing into a bucket, and turn shutoff

valve ON.

4. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Style 2—Copper Line Connection

NOTE: If there is a water supply line that meets the specifications

in “Water Supply Requirements,” proceed to “Connecting to

Refrigerator.” If not, use the following instructions to connect to

the household cold water supply.

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

■ Make sure it is a cold water pipe.

■ Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and keep normal sediment from collecting in the

valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the refrigerator to the water pipe. Add

7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D.

(outside diameter) copper tubing. Be sure both ends of copper

tubing are cut square.

5. Using a cordless drill, drill a ¹⁄₄" (6.35 mm) hole in the cold

water pipe you have selected.

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the ¹⁄₄" (6.35 mm)

drilled hole in the water pipe and that the washer is under the

pipe clamp. Tighten the packing nut. Tighten the pipe clamp

screws slowly and evenly so washer makes a watertight seal.

Do not overtighten.

IMPORTANT: Before attaching the tubing to shutoff valve, flush

the main water supply line to remove particles and air in the water

line. Allow enough flow so that water becomes clear. Flushing the

water line may help avoid filters and/or water valves from

becoming clogged.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten the

clamp or the sleeve. This will crush the copper tubing.

8. Turn off the shutoff valve on the water pipe. Coil the copper

tubing.

9. Connect the flexible, codes-approved water supply line to the

water shutoff valve by threading the provided nut onto the

shutoff valve.

10. Place the end of the tubing into a bucket, and turn shutoff

valve ON.

11. Check for leaks around the saddle valve. Tighten any nuts or

connections (including connections at the valve) that leak.

Connect to Refrigerator

Parts Supplied

■ ¹⁄₄" to ¹⁄₄" (6.35 mm to 6.35 mm) male-to-male coupling

NOTE: The flexible, codes-approved water supply line should

connect to the supply valve through the floor.

1. Unplug the refrigerator or disconnect power.

2. Connect the 7 ft (2.13 m) flexible codes-approved water tube

to the water supply valve.

3. Flush the main water supply line to remove particles and air in

the water line. Allow enough flow so that water becomes clear.

4. Tape the 7 ft (2.13 m) flexible codes-approved water supply

line to the floor, 7" (17.78 cm) from the left side of the

refrigerator. Tape along the length of the tubing, which will

allow it to pass beneath the refrigerator without interference.

NOTE: Allow a minimum of 26" (66.04 cm) of flexible codes-

approved water supply line to be loose at the front of the

refrigerator for connecting to the refrigerator.

A. Bulb

B. Nut

C. Water tubing

A. Cold water pipe

B. Pipe clamp

C. Copper tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

A

B

C

A

B

C

DEF

G

1"

(2.54 cm)

7"

(17.78 cm)

6"

(15.2 cm)

6"

(15.2 cm)

20

5. Connect the 7 ft (2.13 m) flexible codes-approved water

supply line to the refrigerator.

NOTE: If the main water shutoff valve is behind the

refrigerator, a secondary water shutoff valve may be installed

in line with the water supply line at the front of the product.

6. Turn on the water supply valve and check all connections for

leaks.

Plug in Refrigerator

1. Set control switch at top of cabinet to the OFF position.

2. Plug into a grounded 3 prong outlet.

Install Side Trims

The side trims cover the space between the refrigerator and the

adjacent cabinets. There is a trim piece taped to each side of the

refrigerator. Install each trim piece to the side of the refrigerator to

which it is taped.

1. Remove the tape attaching the trim pieces to the sides of the

refrigerator. Set the trim pieces aside.

IMPORTANT: Custom wood panel (with ¹⁄₈" gap) installations

only - The bulb-shaped edge of the side trim piece will

interfere with the panels. Peel the bulb-shaped, long edge

from the trim piece and discard. See the “Top View” graphic

later in this section.

2. Remove the four screws from the side of the refrigerator

cabinet.

3. Using the original holes and the screws removed in Step 2,

fasten the side trim to the refrigerator cabinet.

NOTE: Make sure to fasten each trim piece to the side of the

refrigerator cabinet from which it was removed. The bulb-

shaped edge should be forward with the notch at the top, as

shown.

Top View

A. Household water line

B. Nut (purchased)

C. Ferrule (purchased)

D. Coupling

E. Bulb

F. N u t

G. Refrigerator water tubing

A

B

C

D

E

F

G

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

A. Side trim screws

A. Side trim

B. Adjacent cabinet

C. Door

D. Bulb-shaped edge

A

B

C

D

La page charge ...

Jenn-Air JB36NXFXLE Guide d'installation

Jenn-Air JB36NXFXLE Guide d'installation

dans d''autres langues

Documents connexes

Autres documents