Maytag MDBH969AW Series Manuel utilisateur

Marque: Maytag

Modèle: MDBH969AW Series

Catégorie: Lave-vaisselle

Taper: Manuel utilisateur

INSTALLATION INSTRUCTIONS

UNDERCOUNTER DISHWASHER

PLASTIC GIANT TUB MODELS

INSTRUCTIONS D'INSTALLATION

LAVE-VAISSELLE ENCASTRÉ

MODÈLES À TRÈS GRANDE CUVE EN PLASTIQUE

Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Table des matières . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

W10290309A

Table of Contents

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DISHWASHER SAFETY

You Need to:

• Slowly open dishwasher door while someone grasps the rear of

the dishwasher. Remove shipping materials, drain hose and lower

rack. Close dishwasher door until latched.

• Observe all governing codes and ordinances.

• Install this dishwasher as specified in these instructions.

• Installation should be performed by a qualified service

technician. The dishwasher must be installed to meet all electrical

and plumbing national and local codes and ordinances.

Installation Instructions

(cont.)

Determine Cabinet Opening. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Install The Door Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Choose Attachment Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Move Dishwasher into Cabinet Opening . . . . . . . . . . . . . . . . . . . . . 13

Connect to Water Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Connect to Drain. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Make Direct Wire Electrical Connection. . . . . . . . . . . . . . . . . . . . . . 16

Secure Dishwasher in Cabinet Opening. . . . . . . . . . . . . . . . . . . . . . 18

Complete Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Check Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

If Dishwasher Does Not Operate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Additional Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Dishwasher Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Tools and Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Location Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Product and Cabinet Opening Dimensions . . . . . . . . . . . . . . . . . . . . 4

Drain Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Water Supply Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Electrical Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Prepare Cabinet Opening—Existing Utilities. . . . . . . . . . . . . . . . . . . . 6

Prepare Cabinet Opening—New Utilities. . . . . . . . . . . . . . . . . . . . . . . 6

Prepare and Route Water Line . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Install Drain Hose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Prepare Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Make Power Cord Electrical Connection . . . . . . . . . . . . . . . . . . . . . 11

Wire stripper

Small

tubing cutter

Cordless drill

with ¹⁄₂", ³⁄₄"

and 1¹⁄₂" hole

saw bits

Pliers

UL Listed/CSA

Approved twist-on

wire connectors*

Small level

Utility knife

Phillips

screwdriver

nut drivers or

hex sockets

Measuring tape

or ruler

10" adjustable wrench

that opens to

Flat-blade

screwdriver

wrench

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the recommended tools and parts before starting

installation. Read and follow the instructions provided with any tools

listed here.

All Installations

Tools needed:

*Must be the proper size to connect your household wiring to 16

gauge wiring in dishwasher

Other useful items you may need:

Parts supplied:

Make sure all these parts are included in the literature package.

Parts needed:

Other parts you may also need:

NOTE:

Parts available for purchase in plumbing supply stores.

Check local codes. Check existing electrical supply. See “Electrical

Requirements” section. It is recommended that electrical connections be

made by a licensed electrical installer.

In addition, for first-time installations

Tools needed:

Parts needed:

Location Requirements

Grounded electrical supply required.

Do not run drain lines, water lines or electrical wiring where

they can interfere with or contact dishwasher motor or legs.

The location where the dishwasher will be installed must

provide clearance between motor and flooring. Motor should not

touch the floor.

Do not install dishwasher over carpeted flooring.

Avoid damage from freezing to dishwasher and water lines leading

to dishwasher. Damage from freezing is not covered by the

warranty.

A side panel kit is available from your dealer for installing

your dishwasher at the end of your cabinetry.

A moisture barrier accessory (Part Number 4396277) is available

from your dealer for installing underneath the countertop.

Check location where dishwasher will be installed. The

location must provide:

• easy access to water, electricity and drain.

• convenient access for loading and unloading dishes.

Corner locations require a 2" (5.1 cm) minimum

clearance between the side of the dishwasher door

and the wall or cabinet.

• square opening for proper operation and appearance.

• cabinet front perpendicular to floor.

• level floor. (If floor at front of opening is not level with

floor at rear of opening, shims may be needed to level

dishwasher.)

Helpful Tip: Be sure to accurately measure dimensions

and ensure dishwasher is level if the floor in the dishwasher

opening is uneven (example: flooring extends only partway into

opening).

NOTE: To avoid shifting during dishwasher operation,

shims must be securely attached to the floor.

If dishwasher will be left unused for a period of time or in a

location where it may be subject to freezing, have it winterized by

authorized service personnel.

Make sure pipes, wires and drain hose are within the

shaded area shown in the “Product and Cabinet

Opening Dimensions” section.

Drain hose

Drain hose clamps (2)

(1 large and 1 small)

Phillips-head

screws (2)

Green

Silver

Copper tubing (³⁄₈"

O.D. suggested) or

flexible braided

water supply line

For Direct Wire:

use UL Listed/

CSA Approved

strain relief

to fit ⁷⁄₈" (2.2 cm)

hole

See “Electrical Requirements” section

For Power Supply

Cord: use UL

listed power

supply cord kit

marked for use

with dishwasher

Flashlight

Bath towel

Wood block

Shallow pan

Masking or

duct tape

(38.1– 5 cm)

Screw-type

clamps (3 maximum)

Side mounting kit

for solid surface

countertops

(Part Number

8212560)

Product and Cabinet Opening Dimensions

(61 cm)**

(86.4 cm)

min*

(10.2 cm)

(7.6 cm)

(61 cm)

(4.4 cm)

Check that all surfaces

have no protrusions that would

prohibit dishwasher installation.

(26.7 cm)

(5.1 cm)

(6.4 cm)

(17.2 cm)

(15.9 cm)

lear

Area

(1.9 cm)*

*Insulation may

be compressed.

(not used on all models)

(62.2 cm)

(64.1 cm)

(60.6 cm)

(53.3 cm)

(86 cm) min

with wheels

removed

NOTE: Shaded area of cabinet walls show where utility

connections may be installed.

*Measured from the lowest point on the underside of

countertop. May be reduced to 33⁷⁄₈" (86 cm) by

removing wheels from dishwasher.

**Minimum, measured from narrowest point of

opening.

Drain Requirements

• A new drain hose is supplied with your dishwasher.

If the drain hose is not long enough, use a new drain hose with a

maximum length of 12’ (3.7 m) (Part Number 3385556) that

meets all current AHAM/IAPMO test standards, is resistant to

heat and detergent, and fits the 1" (2.5 cm) drain connector of the

dishwasher.

• Make sure to connect drain hose to waste tee or disposer inlet

above drain trap in house plumbing and 20" (50.8 cm) minimum

above the floor. It is recommended that the drain hose either be

looped up and securely fastened to the underside of the counter,

or be connected to an air gap.

• Make sure to use an air gap if the drain hose is connected to

house plumbing lower than 20" (50.8 cm) above subfloor or floor.

• Use ¹⁄₂" minimum I.D. drain line fittings.

• If required, the air gap should be installed in accordance

with the air gap installation instructions. When connecting the air

gap, a rubber hose (not provided) will be needed to connect to the

waste tee or disposer inlet.

Water Supply Requirements

• A hot water line with 20-120 psi (138-862 kPa) water

pressure can be verified by a licensed plumber.

•120°F (49°C) water at dishwasher.

• ³⁄₈" O.D. copper tubing with compression fitting or

flexible braided water supply line (Part Number 4396897RP)

NOTE:

¹⁄₂" minimum plastic tubing is not recommended.

• A 90° elbow with ³⁄₈" N.P.T. external pipe threads on one

end.

• Do not solder within 6" (15.2 cm) of the water inlet valve.

Use of air gap

Air gap

Electrical Requirements

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electrical Code, ANSI/NFPA

70 - latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169

You must have:

• 120-volt, 60 Hz, AC-only, 15- or 20- amp, fused electrical

supply.

• copper wire only.

We recommend:

• a time-delay fuse or circuit breaker.

• a separate circuit.

If connecting dishwasher

with a power supply cord:

• Use UL listed power supply

cord kit (Part Number 4317824)

marked for use with dishwasher.

• Power supply cord must plug into

a grounded 3 prong outlet, located in the

cabinet next to the dishwasher opening.

Outlet must meet all local codes and

ordinances.

If connecting dishwasher with direct wiring:

• Use flexible, armored or

nonmetallic sheathed,

copper wire with

grounding wire that meets

the wiring requirements for your home and local codes and

ordinances.

• Use a UL Listed/CSA Approved strain relief.

1¹⁄₂"

(3.8 cm)

Power Supply Cord-Drill hole

Preferred location

Optional location

Drill a 1¹⁄₂" (3.8 cm) hole in cabinet side or rear.

See product and cabinet opening dimensions.

NOTE: A grounded 3 prong outlet is required inside a cabinet

next to the dishwasher cabinet opening.

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Disconnect power

Water line

Cable

Do you already have utility

hookups?

Existing utility hookups No existing utility hookups

Yes —Follow instructions in the “Prepare Cabinet

Opening—Existing Utilities” section.

No —

Follow instructions in the “Prepare Cabinet

Opening—New Utilities” section.

INSTALLATION INSTRUCTIONS

Prepare Cabinet Opening—New

Utilities

What type of electrical

connection will you use?

Power Supply Cord:

Follow Option A instructions

Direct Wire:

Follow Option B instructions

Prepare and route the electrical supply

Option A, Power Supply Cord:

“

(15.2 cm)

Water line

Cable

Check water and electrical

placement

If the water line and the cable extend to the locations shown,

proceed to the “Install Drain Hose” section. If they do not reach far

enough, follow the instructions in the “Prepare Cabinet Opening—

New Utilities” section.

Prepare Cabinet Opening—Existing

Utilities

6”

(15

.2 cm)

Direct Wire–Route cable

Route cable from power supply through cabinet hole (cable must

extend to the right front side of cabinet opening).

Tape cable to the floor in area shown. This will keep cable from

moving when dishwasher is moved into cabinet opening.

Woo d

cabinet

Met al

cabinet

Power Supply Cord–Prepare hole

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover hole with grommet (Part Number 302797)

included with power supply cord kit.

¹⁄₂"

(1.3 cm)

Drill hole

Preferred locations

Optional locations

Drill a ¹⁄₂" (1.3 cm) hole in the cabinet side or rear.

Helpful Tip: Routing the water line through the left side of

cabinet opening will make water connection easier.

Hot water line

Measure water supply line

Measure overall length of copper tubing or flexible braided

water supply line. Attach to the hot water line using a

connection configuration that is in compliance with local codes

and ordinances. The water line to the dishwasher should have a

manual shutoff valve.

Prepare and Route Water Line

(1.9 cm)

Direct Wire — Drill hole

Preferred location

Optional location

Drill a ³⁄₄" (1.9 cm) hole in right-hand cabinet side or rear.

See product and cabinet opening dimensions.

Wood

cabinet

Metal

cabinet

Direct Wire–Prepare hole

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover hole with grommet (Part Number 302797

not included)

Helpful Tip: Wiring the dishwasher will be easier if you route the

cable into the cabinet opening from the right-hand side.

Option B, Direct Wire:

Flush water supply line

Slowly turn water shutoff valve to “ON” position. Flush water

into a shallow pan until clear to get rid of particles that could

clog the inlet valve. Turn shutoff valve to “OFF” position.

Drill hole

1¹⁄₂"

(3.8 cm)

If needed, drill a 1¹⁄₂" (3.8 cm) diameter hole in cabinet wall or side

of the opening closest to the sink.

Install Drain Hose

IMPORTANT: Always use a new drain hose. Check local codes

to determine whether an air gap is required.

Drain hose

Route drain hose

Route drain hose as shown through hole in cabinet to the front

center of opening where drain connection will be made. Tape

drain hose to the floor in area shown. This will keep the drain hose

from moving when dishwasher is moved into cabinet opening.

Route water supply line

Slowly route water supply line through hole in cabinet. (If using

copper tubing, it will bend and kink easily, so be gentle.) It

should be far enough into the cabinet opening to connect it to

the dishwasher inlet on the front left side of the dishwasher.

Add 90° elbow fitting to the

water supply line

Connect the ³⁄₈" compression fitting to the water supply

line prior to installing the unit into the cabinet opening.

Attach such that the ³⁄₄" connection is facing upward.

Copper tubing only: Put the tubing into the 90° elbow

fitting as far as it will go (the copper tubing bends and

kinks easily). Slide the nut and ferrule forward and start

the nut onto the elbow threads.

Flexible braided connection: Secure nut to elbow using

⁵⁄₈" open ended wrench or adjustable wrench.

NOTE: Do not use Teflon

®†

tape with compression

fittings.

Slide nut and ferrule

onto tubing

Ferrule

Nut

Copper tubing only: Slide nut, then ferrule, about 1"

(2.5 cm) onto copper tubing.

NOTE: To avoid vibration during operation, route the

water supply line so that it does not touch the

dishwasher base, frame or motor.

†TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

Air gap

Large silver drain

hose clamp

(provided)

Drain trap

Air gap

Large silver drain

hose clamp

Drain hose

Drain trap

Rubber hose

connector

Screw-type clamps

Screw-type clampsScrew-type clamps

Waste tee

No waste disposer – with air gap

1. Connect black end of drain hose to air gap

and cut if needed.

NOTE: Do not cut ribbed section.

2. Attach drain hose to air gap with large silver

drain hose clamp (provided). Use pliers to

squeeze clamp open and move into position.

If the drain hose was cut, use a 1¹⁄₂" to 2"

(3.8 to 5 cm) screw-type clamp (not

provided).

3. Use a rubber hose (not provided) with

screw-type clamps (not provided) to

connect from waste tee to air gap.

Air gap

Large silver drain

hose clamp

(provided)

Disposer inlet

Air gap

Large silver drain

hose clamp

Drain hose

Drain trap

Rubber hose

connector

Disposer inlet

Waste disposer – with air gap

Screw-type clampsScrew-type clampsScrew-type clamps

Black end

Option C, Waste disposer – with air gap

Option D, No waste disposer – with air gap

Connect drain hose to waste tee or waste disposer

using one of the following options:

• Option A, Waste disposer - no air gap

• Option B, No Waste disposer - no air gap

• Option C, Waste disposer - with air gap

• Option D, No waste disposer - with air gap

Connect drain hose

Large silver

drain hose clamp

Drain hose

Drain trapDrain trap

Disposer inletDisposer inlet

Waste disposer – no air gap

1. Using a hammer and screwdriver, knock

plug into disposer.

2. Use needle-nose pliers to remove plug.

3. Attach drain hose to disposer inlet with

large silver drain hose clamp (provided).

Use pliers to squeeze clamp open and

move into position.

Option A, Waste disposer – no air gap

IMPORTANT: The drain hose connection of the disposer or a

waste tee must be made before the drain trap and at least 20"

(50.8 cm) above the floor where the dishwasher will be installed.

Helpful Tip: To reduce vibration of the hose, keep the hose away

from the floor.

Screw-type

clamp

Drain trap

Large silver

drain hose clamp

Drain hose

Drain trap

Waste tee

No waste disposer – no air gap

Waste tee

1. Connect black end of of drain hose to waste

tee and cut if needed.

NOTE: Do not cut ribbed section.

2. Attach black end of drain hose to waste tee

with a large silver drain hose clamp (provided).

Use pliers to squeeze clamp open and move

into position. If the drain hose was cut, use a

1¹⁄₂" to 2" (3.8 to 5 cm) screw-type clamp (not

provided).

Black end

Option B, No waste disposer – no air gap

1. Using a hammer and screwdriver, knock

plug into disposer.

2. Use needle-nose pliers to remove plug.

3. Connect black end of drain hose to air gap

and cut if needed.

NOTE: Do not cut ribbed section.

4. Attach drain hose to air gap with large

silver drain hose clamp (provided). Use

pliers to squeeze clamp open and move

into position. If the drain hose was cut, use

a 1¹⁄₂" to 2" (3.8 to 5 cm) screw-type clamp

(not provided).

5. Use a rubber hose (not provided) with

screw-type clamps (not provided) to

connect from air gap to disposer inlet.

Install strain relief

Remove terminal box cover

Using a ¹⁄₄" hex head socket, nut driver or Phillips screwdriver,

remove terminal box cover. Retain for later use.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

Prepare Dishwasher

Put dishwasher on its back

Helpful Tip: Place cardboard under dishwasher until installed in

cabinet opening to avoid damaging floor covering. Do not use door

panel as a worktable without first covering with a towel to avoid

scratching the door panel.

Using two or more people, grasp sides of dishwasher door frame and

place dishwasher on its back.

Remove panels

Using a ¹⁄₄" hex head socket, nut driver or Phillips screwdriver,

remove the 2 screws attaching access panel and lower panel to

dishwasher.

NOTE: Do not remove tech sheet from access panel.

Install a UL Listed/CSA Approved strain relief. Make sure screw

heads are facing to the left when tightening conduit nut. Strain

relief may be provided with the power supply cord kit.

Tabs

Completed

Install

Attach insulation

Using the precut slots in the insulation, fasten the insulation over the

molded hooks on the tub. Be sure to fasten the insulation down on

both sides of the tub.

What type of electrical

connection will you use?

Power Supply Cord:

Follow Option A instructions

Direct Wire:

Follow Option B instructions

Option A, Power Supply Cord:

Route cord so that it does not touch dishwasher motor to lower

part of dishwasher tub. Pull cord through strain relief in terminal

bow.

Select UL Listed/CSA Approved twist-on wire connectors rated to

connect your power supply cord to 16-gauge dishwasher wiring.

Power Cord—Route cord

into terminal box

Make Power Supply Cord Connection

Remove the green grounding screw and place through the ring

terminal of the green ground wire. Reattach and tighten the

green screw.

Ground

wire

Power Supply Cord—

Connect ground wire

Ground

wire

Washer

Ground

connector

NOTE: Do not pre-twist stranded wire. Twist on wire connector.

Gently tug on wires to be sure both are secured.

Connect wires black to black and white to white, using

UL Listed/CSA Approved twist-on wire connectors.

Power Cord—Connect

remaining wires

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector

in terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

If using Option B, proceed to “Determine Cabinet Opening,” to

continue with the installation of your dishwasher.

Terminal box wire:

white

black

ground connector

Power supply wire:

white

black

ground wire

Wiring configuration

If needed, see website for animated representation of this step.

Visit www.whirlpool.com under FAQ tab.

Tighten strain relief screws to secure cord.

Power Cord—Secure cord

on conduit connector

Place wires inside terminal box. Insert tabs on

left side of cover. Make sure wires are tucked inside box. Close

cover ensuring wires are not pinched. Use ¹⁄₄" nut driver and

previously removed screw to secure cover.

NOTE: Do not plug into outlet until instructed.

Power Cord—Reinstall

terminal box cover

Measure height of cabinet opening from underside of

countertop to floor where dishwasher will be installed (you will

need to measure the lowest point on the underside of the

countertop and the highest point on the floor). Refer to

“Dishwasher Height Adjustment Chart” for wheel position and

the number of turns needed.

Measure cabinet opening

Determine Cabinet Opening

Cabinet

opening height

34" (86.4 cm) 1 10

Removed All the way up

Wheel

position

Number of turns

on front leg

(87.0 cm)

Dishwasher Height Adjustment Chart

NOTE: If the minimum cabinet opening height is less than 34"

(86.4 cm), the rear wheels can be removed for additional

clearance. This will allow the dishwasher to fit into a 33⁷⁄₈"

(86 cm) high cabinet opening, but the dishwasher will be more

difficult to move. (Measurements are approximate. Wheels and

legs are preset at the factory for 34¹⁄₂" [87.6" cm].)

Turn both leveler legs to the same height. Put wheels in the

required position determined from “Dishwasher Height

Adjustment Chart.” (To change wheel position, use a flat-blade

screwdriver to pop out the wheel, then snap into the new

position.)

Adjust wheels and legs

(7 cm

)

(10.1 cm

)

(5 cm

)

Built-up Floors — Add

shims as needed

Option 2, Dishwasher with Stainless Steel Tub Side

Attachment

(for marble, granite or other hard surface countertops)

1. Remove the brackets from the parts package.

2. Break off the end of the bracket along the scored line.

3. With another person holding the dishwasher to keep it

from tipping, open dishwasher door, and place towel

over pump assembly and spray arm of dishwasher.

This will stop screws from falling into pump area when

securing dishwasher to cabinet.

4. Push the plastic buttons out of the side of the tub.

NOTE: Save the buttons to cover the holes after

dishwasher is installed.

Using two or more people, stand the dishwasher up.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

IMPORTANT: The dishwasher must be secured to the

cabinet. There are two brackets, found in the parts bag.

Attach the brackets to the top of the dishwasher if the

countertop if it is wood, laminate or another similar

surface. If your countertop is marble, granite or another

hard surface, install using Option Number 2.

Score

line

Score line

Plastic

button

Install plastic button

5. Push bracket into slot on the side of dishwasher, and

bend tab in toward the side of the dishwasher so that it

keeps the bracket in place.

NOTE: Do not attach the dishwasher. This will be done

later.

Bend

tabs

Bend tab - side mount

Choose Attachment Option

IMPORTANT: Do not scratch the front panel during this

procedure.

Remove the door handle and hardware bag containing

the setscrews and Allen wrench from the cardboard box.

Start setscrews in handle. Place handle on mounting

studs with the setscrews facing down. Push the door

handle tightly against the door. Insert the short end of the

Allen wrench into the setscrews. Tighten the setscrews

¹⁄₄ turn past snug.

Mounting

stud

Mounting stud

Handle

Allen wrench

Setscrew (inside of

door handle standoff)

Install door handle

Install the Door Handle

(on some models)

Option 1, Countertop attachment

1. Remove the brackets from the package and place in

the open slots on the left and right-hand top of the

dishwasher collar as shown.

2. Insert the bracket into the slot on the collar. Using a

pair of pliers, bend the tab down to secure the

bracket in place. Repeat this step for the other side.

NOTE: Do not attach the dishwasher. This will be done

later.

Tabs must point to the right

Install mounting bracket

Bend tab - top mount

Built-up floors (Kitchen floor height is higher than cabinet

opening.) Example: Kitchen floor tile does not extend into

cabinet opening. Add shims as needed in the area shown to

bring the dishwasher up to 34" (86.4 cm) below the countertop.

NOTE: Shims must be securely attached to floor to avoid

movement when the dishwasher is in use.

If the door closes too quickly, decrease the spring tension by

moving the spring end toward the front of the dishwasher.

NOTE: Springs should be in the same notches on left and right

sides.

Closes too quickly—

Decrease spring tension

Door falls open—

Increase spring tension

With another person holding the dishwasher to keep it from

tipping, open and close the door a few times. If the door closes

or falls open under its own weight, the door tension will need to

be adjusted.

Open and close door

Check that water line is on the left side of opening

and drain hose is near the center of the cabinet opening.

Check water and drain

hose position

Move dishwasher close to

cabinet opening

Water

line

Cable

Drain

hose

Direct Wire

Only

IMPORTANT: Double-check correct placement

of utilities. Grasp the sides of the dishwasher at the edges of the

door panel. Tilt dishwasher backward on wheels and move

dishwasher close to cabinet opening.

NOTE: Do not push on the front of the panel or on the console–

they may dent.

Helpful Tip: Temporarily tape utilities to the floor in the

locations shown to keep them from moving when dishwasher is

moved into the cabinet opening.

Move Dishwasher into Cabinet

Opening

Using two or more people, stand dishwasher upright.

NOTE: Do not install kickplate until instructed to do so.

Stand dishwasher upright

Option 3, Dishwasher with Plastic Tub Side Attachment

(for marble, granite or other hard surface countertops)

Order Mounting Bracket Kit Part Number 8212560.

If the door falls open, increase the spring tension by moving the

spring end toward the back of the dishwasher.

NOTE: Springs should be in the same notches on left and right

sides.

IMPORTANT: If wheels were removed, cover the floor when

moving the dishwasher to avoid damage to the floor. Slowly

move dishwasher completely into cabinet opening. Do not kink or

pinch water line, drain hose, power supply cord or direct wire

between dishwasher and cabinet. Remove cardboard from under

dishwasher.

NOTE: It is all right if dishwasher fits tightly into cabinet opening.

Do not remove insulation blanket – the blanket reduces the

sound level.

NOTE: If using power cord, make sure to route end through hole

in cutout before sliding into cabinet opening.

Move dishwasher into

cabinet opening

Insulation

blanket

Insulation

blanket

Align front of dishwasher door panel with front of cabinet doors.

You may need to adjust alignment to be even with your

cabinets.

Align front of dishwasher

with front of cabinet doors

Check for plumb and

adjust legs if needed

Check that leveling legs are firmly against the floor.

Close and latch the door, and place level against the

front panel. Check that dishwasher is centered from front to back

in the opening. If needed, adjust leveling leg until dishwasher is

plumb. Repeat for other side of dishwasher.

Helpful Tip: Push up on front of dishwasher to raise dishwasher

off the ground to adjust front legs. With some installations, it

may be easier to adjust the front leg using the ³⁄₁₆" hex head

socket or adjustable wrench.

Preferred method Optional method

Connect to Water Supply

Tighten 90° elbow fitting to valve

Check level side to side and

adjust legs if needed

Place level against top front opening of tub. Check

that dishwasher is level from side to side. If dishwasher is not

level, adjust front legs up or down until dishwasher is level.

Connect to Drain

Place towel under drain hose to catch any water in drain hose.

Place the small green drain hose clamp onto the small end of

the drain hose. Push the new drain hose into the black drain

hose connector up to the drain hose stop.

Connect drain hose

Drain hose

Green clamp

Black drain hose

connector

Stop

Drain hose stop

Slide clamp onto connector

Drain hose

Green clamp

Black drain hose

connector

Stop

Drain hose stop

Using pliers, squeeze open the small green drain hose clamp

and slide onto connector between stops.

Make Direct Wire Electrical

Connection

Route cable so that it does not touch dishwasher motor or

lower part of dishwasher tub. Pull cable through cable clamp in

terminal box.

Select UL listed or CSA approved twist-on wire connectors

(not included) rated to connect your household wiring to 16-gauge

dishwasher wiring.

Direct Wire—Route cable

into terminal box

Option B, Direct Wire:

Hose clamp final position

Drain hose

Green clamp

Black drain hose

connector

Stop

Drain hose stop

Once connected, remove towel.

If needed, see website for animated representation of this step.

Visit www.whirlpool.com/drain under FAQ tab.

NOTE: If the power supply cord was connected earlier

proceed to “Secure Dishwasher in Cabinet Opening” section.

Place paper towel under 90° elbow fitting. Turn on water

supply and check for leaks. If leak occurs, repeat previous step.

If needed, see website for animated representation

of this step. Visit www.whirlpool.com/watersupply under

FAQ tab.

NOTE: Do not use Teflon tape with compression fittings.

Check for leaks

Be sure rubber washer is properly seated in fitting. Slide the ³⁄₄"

fitting up to the valve and hand tighten to avoid unintentional

cross-threading. Hand tighten until the coupling is tight. Using

pliers, check the tightness of the coupling. An additional ¹⁄₄ to ¹⁄₂

turn may be required to seal the rubber gasket.

NOTE: Do not overtighten. Damage to the coupling can result.

Form bare ground wire into a U-shaped hook. Wrap ground wire

hook clockwise around ground connector screw and under the

washer. Securely tighten ground connector.

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector

in terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

Ground

wire

Direct Wire—Connect

ground wire

Ground

wire

Washer

Ground

connector

Terminal box wire:

white

black

ground connector

Power supply wire:

white

black

ground wire

Wiring configuration

If needed, see website for animated representation

of this step. Visit www.whirlpool.com/electrical under FAQ

tab.

NOTE: Do not pre-twist stranded wire. Twist on UL Listed/CSA

Approved wire connector. Gently tug on wires to be sure both

are secured.

Connect wires black to black and white to white, using UL

Listed/CSA Approved twist-on wire connectors (not included).

Direct Wire—Connect

remaining wires

Tighten strain relief screws to secure cable.

Direct Wire—Secure cable

in conduit connector

Place wires inside terminal box. Insert tabs on left side of cover.

Make sure wires are tucked inside box. Close cover ensuring

wires are not pinched. Use

¹⁄₄" nut driver and previously

removed screw to secure cover.

Direct Wire—Reinstall

terminal box cover

Secure Dishwasher in Cabinet

Opening

Double check dishwasher

alignment in cabinet opening

Open dishwasher door, remove lower dish rack, and place towel

over pump assembly and lower spray arm of dishwasher. This

will keep the screws from falling into pump area when you are

securing dishwasher to countertop.

Check that dishwasher is still level front to back and side to side

in cabinet opening.

IMPORTANT: If you have solid countertops such as Corian

†

granite, etc., you must use side mounting kit (Part Number

8212560). Follow kit instructions. (Brackets included with kit.)

Remove lower dish rack

and place towel

NOTE: Do not drop screws into bottom of dishwasher.

Locate brackets on top of dishwasher and secure dishwasher to

countertop with two, #10 x ¹⁄₂" Phillips-head screws (included).

The dishwasher must be secured to keep it from shifting when

door is opened.

Secure dishwasher

Check that top of door does not contact screws, brackets, or

countertop. If it does, adjust leveling legs.

Check door clearance

Check inner spacing

Open door and check that space between dishwasher cabinet

opening and tub is equal on both sides. If spacing is not equal,

loosen bracket screws secured and shift tub. Tighten bracket

screws.

†Corian is a registered trademark of E.I. Du Pont De Nemours and Company.

Remove towel from dishwasher. Reinstall the lower dish rack.

Remove towel and replace

lower dishwasher rack

If needed, see website for animated representation

of this step. Visit www.whirlpool.com/anchoring under FAQ

tab.

Check that grounding clip is attached to the lower panel.

Position the lower panel behind the access panel. On some

models there is insulation on the access panel which must

fall behind the insulation on the lower panel.

Reinstall access panels

ounding

clip

Grounding

clip

Insulation

(on some models)

Lower

panel

Access

panel

Complete Installation

Check that the lower edge of the lower panel contacts

the floor. Adjust if necessary.

Check lower panel edge

Hold the two panels together and place them against

dishwasher leg. Using a Phillips or ¹⁄₄" screwdriver, reinstall

the screws through the holes in the access panel and the

slots in the lower panel.

Reinstall access panels

Tighten access panel screws.

Tighten screws

First try the solutions suggested here to possibly avoid the cost

of a service call.

• Has the circuit breaker tripped or the house fuse

blown?

• Is the door closed tightly and latched?

• Has the cycle been set correctly to start the dishwasher?

• Is the water turned on?

If none of these work, call 1-800-253-1301, or in Canada, call

1-800-807-6777.

For Roper models, call 1-800-447-6737, or in Canada call

1-800-807-6777.

If Dishwasher Does Not Operate

Expect longer wash times. Your new dishwasher will average 2

to 3 hours per load, but use nearly 40% less energy than older

models. Designed with a low wattage, low energy consumption

motor, your dishwasher washes longer to ensure exceptional

cleaning. Certain models are equipped with an optical water

sensor so the first cycle will run longer to calibrate to optical

sensor. Selecting certain options could increase cycle time past

3.5 hours.

Rinse Aid is necessary for good drying results:

This dishwasher is designed to be used with rinse aid for good

drying performance and controlling hard water deposit buildup.

Energy efficient dishwashers use less water and energy so they

depend on the water sheeting action of rinse aid for good

drying performance.

Start/Resume light may flash:

When pressing Start/Resume, you must make sure the door is

closed within 3 seconds. If you do not, the Start/Resume light

will flash until you press it again. (You must also do this when

adding a dish during the middle of a cycle.)

NOTE: If a braided supply hose is used, replace inlet hose after

5 years to reduce the risk of hose failure. Record hose installation

or replacement dates on the hose for future reference.

Additional Tips

❏

Read the Dishwasher User Instructions that came with your

dishwasher.

❏

Check that all parts have been installed and no steps were

skipped. Check that you have all tools used.

❏

Start dishwasher and allow it to complete the shortest wash

cycle. After the first 2 minutes unlatch door, wait 5 seconds,

then open door. Check to see that there is water in the

bottom of the dishwasher tub. Check that dishwasher is

working properly.

If dishwasher is not working properly, disconnect power or

unplug dishwasher and see “If Dishwasher Does Not

Operate” section.

Check Operation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result

in death, fire, or electrical shock.

Plug into a grounded 3 prong outlet. Check that power supply

cord does not touch dishwasher motor or lower part of

dishwasher tub.

Power supply cord—Plug into

a grounded 3 prong outlet

Reconnect electrical power at the fuse box or circuit

breaker box.

Reconnect power

Reconnect Power

La page charge ...

Maytag MDBH969AW Series Manuel utilisateur

Marque: Maytag

Modèle: MDBH969AW Series

Catégorie: Lave-vaisselle

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag MDBH969AW Series User manual

Maytag MDBH969AW Series Manuel utilisateur

Maytag MDBH969AW Series Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents